Fiber Matrix 6400 Setup Guide

Fiber Matrix 6400 Setup Guide
Setup Guide
Fiber Matrix 6400
Configurable Fiber Optic Digital Matrix Switchers
Extron USA - West
Headquarters
+800.633.9876
Inside USA / Canada Only
+1.714.491.1500
+1.714.491.1517 FAX
Extron USA - East
Extron Europe
Extron Asia
Extron Japan
Extron China
Extron Middle East
+800.633.9876
+800.3987.6673
+800.7339.8766
+81.3.3511.7655
+81.3.3511.7656 FAX
+400.883.1568
+971.4.2991800
+971.4.2991880 FAX
+1.919.863.1794
+1.919.863.1797 FAX
+31.33.453.4040
+31.33.453.4050 FAX
+65.6383.4400
+65.6383.4664 FAX
Inside USA / Canada Only
Inside Europe Only
Inside Asia Only
© 2009 Extron Electronics. All rights reserved.
Inside China Only
+86.21.3760.1568
+86.21.3760.1566 FAX
68-1371-50 Rev. B
10 09
Precautions
Safety Instructions • English
This symbol is intended to alert the user of important
operating and maintenance (servicing) instructions in
the literature provided with the equipment.
This symbol is intended to alert the user of the
presence of uninsulated dangerous voltage within
the product’s enclosure that may present a risk of
electric shock.
Caution
Read Instructions • Read and understand all safety and operating
instructions before using the equipment.
Retain Instructions • The safety instructions should be kept for future
reference.
Follow Warnings • Follow all warnings and instructions marked on the
equipment or in the user information.
Avoid Attachments • Do not use tools or attachments that are not
recommended by the equipment manufacturer because they may be
hazardous.
Consignes de Sécurité • Français
Ce symbole sert à avertir l’utilisateur que la
documentation fournie avec le matériel contient des
instructions importantes concernant l’exploitation et
la maintenance (réparation).
Ce symbole sert à avertir l’utilisateur de la présence
dans le boîtier de l’appareil de  tensions dangereuses
non isolées posant des risques d’électrocution.
Attention
Lire les instructions• Prendre connaissance de toutes les consignes de
sécurité et d’exploitation avant d’utiliser le matériel.
Conserver les instructions• Ranger les consignes de sécurité afin de pouvoir
les consulter à l’avenir.
Respecter les avertissements • Observer tous les avertissements et consignes
marqués sur le matériel ou présentés dans la documentation utilisateur.
Eviter les pièces de fixation • Ne pas utiliser de pièces de fixation ni d’outils
non recommandés par le fabricant du matériel car cela risquerait de poser
certains dangers.
Sicherheitsanleitungen • Deutsch
Dieses Symbol soll dem Benutzer in der im
Lieferumfang enthaltenen Dokumentation
besonders wichtige Hinweise zur Bedienung und
Wartung (Instandhaltung) geben.
Dieses Symbol soll den Benutzer darauf aufmerksam
machen, daß im Inneren des Gehäuses dieses
Produktes gefährliche Spannungen, die nicht isoliert
sind und die einen elektrischen Schock verursachen
können, herrschen.
Achtung
Lesen der Anleitungen • Bevor Sie das Gerät zum ersten Mal verwenden,
sollten Sie alle Sicherheits-und Bedienungsanleitungen genau durchlesen
und verstehen.
Aufbewahren der Anleitungen • Die Hinweise zur elektrischen Sicherheit
des Produktes sollten Sie aufbewahren, damit Sie im Bedarfsfall darauf
zurückgreifen können.
Befolgen der Warnhinweise • Befolgen Sie alle Warnhinweise und
Anleitungen auf dem Gerät oder in der Benutzerdokumentation.
Keine Zusatzgeräte • Verwenden Sie keine Werkzeuge oder Zusatzgeräte,
die nicht ausdrücklich vom Hersteller empfohlen wurden, da diese eine
Gefahrenquelle darstellen können.
Instrucciones de seguridad • Español
Este símbolo se utiliza para advertir al usuario
sobre instrucciones importantes de operación y
mantenimiento (o cambio de partes) que se desean
destacar en el contenido de la documentación
suministrada con los equipos.
Este símbolo se utiliza para advertir al usuario sobre
la presencia de elementos con voltaje peligroso sin
protección aislante, que puedan encontrarse dentro
de la caja o alojamiento del producto, y que puedan
representar riesgo de electrocución.
Precaucion
Leer las instrucciones • Leer y analizar todas las instrucciones de operación y
seguridad, antes de usar el equipo.
Conservar las instrucciones • Conservar las instrucciones de seguridad para
futura consulta.
Obedecer las advertencias • Todas las advertencias e instrucciones marcadas
en el equipo o en la documentación del usuario, deben ser obedecidas.
Evitar el uso de accesorios • No usar herramientas o accesorios que no
sean especificamente recomendados por el fabricante, ya que podrian
implicar riesgos.
Warning
Power sources • This equipment should be operated only from the power source
indicated on the product. This equipment is intended to be used with a main power
system with a grounded (neutral) conductor. The third (grounding) pin is a safety
feature, do not attempt to bypass or disable it.
Power disconnection • To remove power from the equipment safely, remove all power
cords from the rear of the equipment, or the desktop power module (if detachable),
or from the power source receptacle (wall plug).
Power cord protection • Power cords should be routed so that they are not likely to be
stepped on or pinched by items placed upon or against them.
Servicing • Refer all servicing to qualified service personnel. There are no userserviceable parts inside. To prevent the risk of shock, do not attempt to service
this equipment yourself because opening or removing covers may expose you to
dangerous voltage or other hazards.
Slots and openings • If the equipment has slots or holes in the enclosure, these are
provided to prevent overheating of sensitive components inside. These openings
must never be blocked by other objects.
Lithium battery • There is a danger of explosion if battery is incorrectly
replaced. Replace it only with the same or equivalent type recommended by
the manufacturer. Dispose of used batteries according to the manufacturer’s
instructions.
Avertissement
Alimentations• Ne faire fonctionner ce matériel qu’avec la source d’alimentation
indiquée sur l’appareil. Ce matériel doit être utilisé avec une alimentation principale
comportant un fil de terre (neutre). Le troisième contact (de mise à la terre) constitue
un dispositif de sécurité : n’essayez pas de la contourner ni de la désactiver.
Déconnexion de l’alimentation• Pour mettre le matériel hors tension sans danger,
déconnectez tous les cordons d’alimentation de l’arrière de l’appareil ou du module
d’alimentation de bureau (s’il est amovible) ou encore de la prise secteur.
Protection du cordon d’alimentation • Acheminer les cordons d’alimentation de
manière à ce que personne ne risque de marcher dessus et à ce qu’ils ne soient pas
écrasés ou pincés par des objets.
Réparation-maintenance • Faire exécuter toutes les interventions de réparationmaintenance par un technicien qualifié. Aucun des éléments internes ne peut être
réparé par l’utilisateur. Afin d’éviter tout danger d’électrocution, l’utilisateur ne doit
pas essayer de procéder lui-même à ces opérations car l’ouverture ou le retrait des
couvercles risquent de l’exposer à de hautes tensions et autres dangers.
Fentes et orifices • Si le boîtier de l’appareil comporte des fentes ou des orifices, ceux-ci
servent à empêcher les composants internes sensibles de surchauffer. Ces ouvertures
ne doivent jamais être bloquées par des objets.
Lithium Batterie • Il a danger d’explosion s’ll y a remplacment incorrect de la batterie.
Remplacer uniquement avec une batterie du meme type ou d’un ype equivalent
recommande par le constructeur. Mettre au reut les batteries usagees conformement
aux instructions du fabricant.
Vorsicht
Stromquellen • Dieses Gerät sollte nur über die auf dem Produkt angegebene
Stromquelle betrieben werden. Dieses Gerät wurde für eine Verwendung mit einer
Hauptstromleitung mit einem geerdeten (neutralen) Leiter konzipiert. Der dritte
Kontakt ist für einen Erdanschluß, und stellt eine Sicherheitsfunktion dar. Diese
sollte nicht umgangen oder außer Betrieb gesetzt werden.
Stromunterbrechung • Um das Gerät auf sichere Weise vom Netz zu trennen, sollten
Sie alle Netzkabel aus der Rückseite des Gerätes, aus der externen Stomversorgung
(falls dies möglich ist) oder aus der Wandsteckdose ziehen.
Schutz des Netzkabels • Netzkabel sollten stets so verlegt werden, daß sie nicht im
Weg liegen und niemand darauf treten kann oder Objekte darauf- oder unmittelbar
dagegengestellt werden können.
Wartung • Alle Wartungsmaßnahmen sollten nur von qualifiziertem Servicepersonal
durchgeführt werden. Die internen Komponenten des Gerätes sind wartungsfrei.
Zur Vermeidung eines elektrischen Schocks versuchen Sie in keinem Fall, dieses
Gerät selbst öffnen, da beim Entfernen der Abdeckungen die Gefahr eines
elektrischen Schlags und/oder andere Gefahren bestehen.
Schlitze und Öffnungen • Wenn das Gerät Schlitze oder Löcher im Gehäuse aufweist,
dienen diese zur Vermeidung einer Überhitzung der empfindlichen Teile im
Inneren. Diese Öffnungen dürfen niemals von anderen Objekten blockiert werden.
Litium-Batterie • Explosionsgefahr, falls die Batterie nicht richtig ersetzt
wird. Ersetzen Sie verbrauchte Batterien nur durch den gleichen oder einen
vergleichbaren Batterietyp, der auch vom Hersteller empfohlen wird. Entsorgen Sie
verbrauchte Batterien bitte gemäß den Herstelleranweisungen.
Advertencia
Alimentación eléctrica • Este equipo debe conectarse únicamente a la fuente/tipo
de alimentación eléctrica indicada en el mismo. La alimentación eléctrica de este
equipo debe provenir de un sistema de distribución general con conductor neutro
a tierra. La tercera pata (puesta a tierra) es una medida de seguridad, no puentearia
ni eliminaria.
Desconexión de alimentación eléctrica • Para desconectar con seguridad la acometida
de alimentación eléctrica al equipo, desenchufar todos los cables de alimentación
en el panel trasero del equipo, o desenchufar el módulo de alimentación (si fuera
independiente), o desenchufar el cable del receptáculo de la pared.
Protección del cables de alimentación • Los cables de alimentación eléctrica se deben
instalar en lugares donde no sean pisados ni apretados por objetos que se puedan
apoyar sobre ellos.
Reparaciones/mantenimiento • Solicitar siempre los servicios técnicos de personal
calificado. En el interior no hay partes a las que el usuario deba acceder. Para evitar
riesgo de electrocución, no intentar personalmente la reparación/mantenimiento
de este equipo, ya que al abrir o extraer las tapas puede quedar expuesto a voltajes
peligrosos u otros riesgos.
Ranuras y aberturas • Si el equipo posee ranuras o orificios en su caja/alojamiento,
es para evitar el sobrecalientamiento de componentes internos sensibles. Estas
aberturas nunca se deben obstruir con otros objetos.
Batería de litio • Existe riesgo de explosión si esta batería se coloca en la posición
incorrecta. Cambiar esta batería únicamente con el mismo tipo (o su equivalente)
recomendado por el fabricante. Desachar las baterías usadas siguiendo las
instrucciones del fabricante.
Extron’s Warranty
Extron Electronics warrants this product against defects in materials and workmanship
for a period of three years from the date of purchase. In the event of malfunction during
the warranty period attributable directly to faulty workmanship and/or materials,
Extron Electronics will, at its option, repair or replace said products or components,
to whatever extent it shall deem necessary to restore said product to proper operating
condition, provided that it is returned within the warranty period, with proof of
purchase and description of malfunction to:
USA, Canada, South America,
and Central America:
Extron Electronics 1001 East Ball Road
Anaheim, CA 92805, USA
Europe, Africa, and the Middle East:
Extron Electronics, Europe
Beeldschermweg 6C
3821 AH Amersfoort
The Netherlands
Asia:
Extron Electronics, Asia
135 Joo Seng Road, #04-01
PM Industrial Bldg.
Singapore 368363
Japan:
Extron Electronics, Japan
Kyodo Building
16 Ichibancho
Chiyoda-ku, Tokyo 102-0082
Japan
This Limited Warranty does not apply if the fault has been caused by misuse, improper
handling care, electrical or mechanical abuse, abnormal operating conditions or nonExtron authorized modification to the product.
If it has been determined that the product is defective, please call Extron and ask for an
Applications Engineer at (714) 491-1500 (USA), 31.33.453.4040 (Europe), 65.6383.4400
(Asia), or 81.3.3511.7655 (Japan) to receive an RA# (Return Authorization number). This
will begin the repair process as quickly as possible.
Units must be returned insured, with shipping charges prepaid. If not insured, you
assume the risk of loss or damage during shipment. Returned units must include the
serial number and a description of the problem, as well as the name of the person to
contact in case there are any questions.
Extron Electronics makes no further warranties either expressed or implied with respect
to the product and its quality, performance, merchantability, or fitness for any particular
use. In no event will Extron Electronics be liable for direct, indirect, or consequential
damages resulting from any defect in this product even if Extron Electronics has been
advised of such damage.
Please note that laws vary from state to state and country to country, and that some
provisions of this warranty may not apply to you.
安全须知 • 中文
警告
这个符号提示用户该设备用户手册中
有重要的操作和维护说明。
电源 • 该 设 备 只 能 使 用 产 品 上 标 明 的 电 源 。 设 备
必须使用有地线的供电系统供电。 第三条线
(地线)是安全设施,不能不用或跳过。
这个符号警告用户该设备机壳内有暴
拔掉电源 • 为安全地从设备拔掉电源,请拔掉所有设备后
或桌面电源的电源线,或任何接到市电系统的电源线。
露的危险电压,有触电危险。
电源线保护 • 妥善布线, 避免被踩踏,或重物挤压。
注意
阅读说明书 • 用 户 使 用 该 设 备 前 必 须 阅 读 并 理
解所有安全和使用说明。
保存说明书 • 用户应保存安全说明书以备将来使
用。
遵守警告 • 用户应遵守产品和用户指南上的所有安
全和操作说明。
维护 • 所有维修必须由认证的维修人员进行。 设备内部
没有用户可以更换的零件。为避免出现触电危险不要自
己试图打开设备盖子维修该设备。
通风孔 • 有些设备机壳上有通风槽或孔,它们是用来防止
机内敏感元件过热。 不要用任何东西挡住通风孔。
锂电池 • 不正确的更换电池会有爆炸的危险。 必须使用
与厂家推荐的相同或相近型号的电池。 按照生产厂的
建议处理废弃电池。
避免追加 • 不要使用该产品厂商没有推荐的工具或
追加设备,以避免危险。
FCC Class A Notice
This equipment has been tested and found to comply with the limits for a Class A digital device,
pursuant to part 15 of the FCC Rules. Front Panel Operation is subject to the following two
conditions: (1) this device may not cause harmful interference, and (2) this device must accept any
interference received, including interference that may cause undesired operation. The Class A limits
are designed to provide reasonable protection against harmful interference when the equipment
is operated in a commercial environment. This equipment generates, uses, and can radiate radio
frequency energy and, if not installed and used in accordance with the instruction manual, may
cause harmful interference to radio communications. Front Panel Operation of this equipment in
a residential area is likely to cause harmful interference, in which case the user will be required to
correct the interference at his own expense.
N
This unit was tested with shielded cables on the peripheral devices. Shielded cables must be used
with the unit to ensure compliance with FCC emissions limits.
Table of Contents
Chapter One • Introduction ................................................... 1-1
About this Manual..................................................................... 1-2
About the Fiber Matrix 6400 Switchers.............................. 1-2
Configurability and transmission modes.............................. 1-4
Chapter Two • Installation....................................................... 2-1
Rear Panel..................................................................................... 2-2
A note on I/O boards.............................................................. 2-2
Making connections................................................................ 2-4
Front Panel. .................................................................................. 2-6
Chapter Three • Front Panel Operation.......................... 3-1
Creating a Tie............................................................................... 3-2
Viewing Ties (and Muting Outputs).................................... 3-2
Saving or Recalling a Preset. .................................................. 3-3
Locking Out the Front Panel (Executive Mode). .............. 3-3
Chapter Four • Remote Control............................................ 4-1
Selected SIS Commands........................................................... 4-2
Establishing a network (Ethernet) connection..................... 4-2
Connection timeouts...............................................................4-2
Number of connections...........................................................4-3
Verbose mode..........................................................................4-3
Host-to-switcher instructions.................................................4-3
Installing and Starting the Control Program..................... 4-8
Installing the program............................................................ 4-8
Starting the program.............................................................. 4-9
Accessing the HTML Pages.................................................... 4-11
Configuring for Network Communication.......................... 4-11
Loading the start-up page.................................................... 4-13
Chapter Five • Maintenance and Modifications....... 5-1
Removing and Installing an I/O Board or Blank Panel... 5-2
Removing and Installing a Power Supply Module.......... 5-4
Fiber Matrix 6400 Switcher • Table of Contents
Refer also to the Fiber Matrix 6400 Switcher User’s Manual at www.extron.com.
i
Table of Contents, cont’d
Fiber Matrix 6400 Switcher
1
Chapter One
Introduction
About this Manual
About the Fiber Matrix 6400 Switchers
All trademarks mentioned in this manual are the properties of their respective owners.
ii
Fiber Matrix 6400 Switcher • Table of Contents
Refer also to the Fiber Matrix 6400 Switcher User’s Manual at www.extron.com.
Introduction
FOX 500 Tx
V
R
RGB
REMOTE
RS-232 ALARM
Tx Rx
1
FOX 500
Transmitter
•
Perform basic operations
•
Use both the front panel controls and selected
Simple Instruction Set (SIS™) commands
•
Load and start up the Windows®-based Matrix Switchers
Control Program
•
Connect to the built-in HTML pages, which you can use
to operate the switcher
•
Replace the I/O boards and power supplies
About the Fiber Matrix 6400 Switchers
The Fiber Matrix 6400 (figure 1-1) is a configurable matrix
switcher that distributes optical and electrical signals. Fiber
optic I/O boards route signals that are compatible with all
Extron FOX 500 fiber optic product lines. SDI/HD-SDI I/O
boards route serial digital interface (SDI) and high definition
serial digital interface (HD-SDI) signals. The matrix switcher
routes any input signal to any combination of outputs. An
optical input can be tied to optical and/or SDI/HD-SDI outputs
and an SDI/HD-SDI input can be tied to SDI/HD-SDI and/or
optical outputs. The matrix switcher can route multiple input/
output configurations simultaneously.
1-2
Fiber Matrix 6400 Switcher • Introduction
Refer also to the Fiber Matrix 6400 Switcher User’s Manual at www.extron.com.
OUT
IN
OUT
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
R
G
H/HV
V
B
L
RGB
R
IN
OPTICAL
POWER
12V
0.3A MAX
Tx
Rx
OUT
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
S
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
C
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
H
G
F
E
IN
OUT
IN
OUT
IN
OUT
IN
H
G
G
F
H
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
B
C
IN
OUT
IN
OUT
IN
OUT
Tx Rx
L
BUFFERED OUTPUTS
FOX HD-SDI
R
E
OPTICAL
2* 1
NA
REMOTE
RS-232 ALARM
1
2
OPTIONAL FOR
* RETURN
DATA
IN
IN
H
G
D
FOX 500 DVI Rx
RS-232
OVER FIBER
AUDIO OUTPUTS
DVI - D OUTPUT
H
G
F
LINK
Singlemode
IN
H
G
F
E
A
IN
OPTIONAL FOR
* RETURN
DATA
2
FOX 500 DVI
Receiver
H
G
F
E
D
MUTI-RATE SDI INPUTS
F
E
D
C
D
E
D
C
B
B
F
E
D
C
B
A
A
D
C
B
A
OUT
E
G
Tx Rx
A
OUT
C
B
A
OUT
D
F
IN
H
F
G
H
MUTI-RATE SDI OUTPUTS
PRIMARY POWER SUPPLY
REDUNDANT POWER SUPPLY
FOX 500 Receiver
2
100-240V 0.3A
50/60 Hz
RS-232
OVER FIBER
RGB OUTPUTS
Tx Rx
PRIMARY
ANAHEIM, CA
R
G
B
H
V
S
M
Multimode
S
Singlemode
D
SDI / HD-SDI
FOX 500 Rx
L
R
RGB
REMOTE
RS-232 ALARM
Tx Rx
OPTICAL
2* 1
NA
AUDIO OUTPUTS
100-240V
50/60Hz
1.2A MAX.
OPTIONAL FOR
* RETURN
DATA
1
2
OPTIONAL FOR
* RETURN
DATA
FOX HD-SDI
Singlemode
OPTICAL
POWER
12V
0.3A MAX
CONFIG
HD/SDI IN
OUT
IN
OUT
IN
1
Singlemode
OPTICAL
1 2*
NA
1
FOX HD-SDI
Multimode
IN
IN
E
100-240V 0.3A
50/60 Hz
B
OUT
FOX 500 Tx
REMOTE
RS-232 ALARM
Tx Rx
OUT
REDUNDANT
AUDIO INPUTS
OR
OUT
IN
D
C
OUT
M
A
OUT
100-240V
50/60Hz
1.2A MAX.
RS-232
OVER FIBER
INPUT LOOP THRU
IN
1-8
9 - 16
D
LINK
RGB INPUT
About this Manual
Connect the hardware
IN
IN
Singlemode
Tx Rx
•
49 - 56
M
100-240V 0.3A
50/60 Hz
This setup guide helps you to easily and quickly set up and
configure your Extron Fiber Matrix 6400 Switcher. Step by step
instructions show you how to:
41 - 48
S
LINK
to the Fiber Matrix 6400 Switcher User’s Manual,
available on the Extron DVD or at www.extron.com.
33 - 40
M
N For more information on any subject in this guide, refer
OUT
B
A
OPTIONAL FOR
* RETURN
DATA
2
OUT
IN
C
OUT
S
Tx Rx
LINK
L
OPTICAL
1 2*
NA
AUDIO INPUTS
IN
B
IN
OPTICAL
2* 1
NA
REMOTE
RS-232 ALARM
LINK
H/HV
ACT LINK
LAN
Tx Rx
B
OR
REMOTE
RS-232
OVER FIBER
INPUT LOOP THRU
G
OUT
A
OUT
RS232/RS422
RGB INPUT
R
IN
OUT
M
RESET
Multimode
R
Fiber Matrix 6400
Modular Fiber Optic
Matrix Switcher
FOX 500
Transmitter
100-240V 0.3A
50/60 Hz
L
LINK
Tx Rx
AUDIO OUTPUTS
DVI - D OUTPUT
OPTIONAL FOR
* RETURN
DATA
FOX 500 DVI Rx
RS-232
OVER FIBER
OPTICAL
1 2*
2
57 - 64
transceivers when the fiber optic cable is
unplugged.
1
17 - 24
Tx Rx
LINK
REMOTE
RS-232 ALARM
25 - 32
R
100-240V 0.3A
50/60 Hz
FOX 500 DVI Tx
NA
AUDIO INPUTS
LINK
Tx Rx
LOOP - THRU
LINK
RS-232
OVER FIBER
DDC
RESOL
LINK
100-240V 0.3A
50/60 Hz
L
• Plug the attached dust caps into the optical
Multimode
Multimode
DVI - D INPUT
• Do not look into the rear panel fiber optic
cable connectors or into the fiber optic cables
themselves.
FOX 500 DVI
Receiver
FOX 500 DVI
Transmitter
LINK
continuous invisible light, which may be harmful and
dangerous to the eyes; use with caution.
LINK
W The Fiber Matrix 6400’s fiber optic I/O boards output
CONFIG
HD/SDI IN
Tx
Rx
BUFFERED OUTPUTS
FOX HD-SDI
Figure 1-1 — Typical Fiber Matrix 6400 application
The Extron proprietary fiber optic signal, generated by FOX 500
transmitters, can include video, stereo audio, and transmitterto-receiver RS-232 serial communication. The video component
of the signal can be RGB video, Digital Visual Interface (DVI)
video, SDI/HD-SDI video, or low resolution video, depending
on the transmitter and receiver.
The matrix switcher can be remotely controlled via its Ethernet
LAN port or either of two serial ports using either Windowsbased Extron Matrix Switchers Control Program or the SIS.
The switcher has two internal, hot-swappable 100 VAC to
240 VAC, 50-60 Hz, 180-watt power supplies that provide
worldwide power compatibility and reliability.
N Compatible optical signals are digital signals from
270 Mbs through 4.25 Gbps that are sent and received via
fiber optic small form factor pluggable (SFP) modules. The
Fiber Matrix 6400 supports all compatible optical signals,
whether transmitted or received by an Extron FOX system
component or not.
Fiber Matrix 6400 Switcher • Introduction
Refer also to the Fiber Matrix 6400 Switcher User’s Manual at www.extron.com.
1-3
Introduction, cont’d
N The FOX 500 transmitter-to-receiver communications,
including the serial link, occupy one matrix switcher input
and output.
This matrix switcher also supports the FOX 500 return
(receiver-to-transmitter) serial communications, but
returning this signal stream to the transmitter occupies a
separate matrix switcher input and output.
Configurability and transmission modes
The Fiber Matrix is assembled from individual input/output
(I/O) boards. The switcher can include up to eight I/O boards,
each of which supports eight inputs by eight outputs. The three
types of I/O boards are:
•
Singlemode fiber optic 8x8 I/O board, equipped with
removable fiber optic transceiver modules
•
Multimode fiber optic 8x8 I/O board, equipped with
removable fiber optic transceiver modules
•
SDI/HD-SDI 8x8 I/O board, equipped with permanent
BNC connectors
N As listed above, two versions of the fiber optic I/O boards
are documented in this manual. They are categorized by
the type of fiber optic cable, multimode or singlemode,
which defines the effective range of transmission:
•
•
Singlemode — Very long distance, up to 30 km
(18.75 miles)
Multimode — Long distance, up to 150 m (450 feet)
By adding or removing I/O boards, you can expand and
contract the Fiber Matrix from an 8-input by 8-output matrix to
a 64-input by 64-output matrix.
N On a fiber optic I/O board as delivered from Extron, all
transceiver modules are configured the same: either all
multimode or all singlemode. You can mix multimode
and singlemode fiber optic I/O boards in a Fiber Matrix
switcher, but you must ensure that you connect the proper
transmission mode fiber cables to the board.
1-4
Fiber Matrix 6400 Switcher • Introduction
Refer also to the Fiber Matrix 6400 Switcher User’s Manual at www.extron.com.
Fiber Matrix 6400 Switcher
2
Chapter Two
Installation
Rear Panel
Front Panel
Installation
Rear Panel
1
A note on I/O boards
1-8
ACT LINK
D
IN
OUT
IN
OUT
Output 9
Output 10
Input 9
A
C
B
B
Input 10
D
C
Output 12
Input 11
E
G
F
IN
OUT
IN
OUT
Input 12
IN
OUT
ACT LINK
9 - 16
17 - 24
A
2
IN
IN
OUT
IN
IN
OUT
A
IN
OUT
IN
IN
IN
OUT
B
C
D
E
F
IN
OUT
C
G
H
A
B
C
B
C
D
E
F
IN
E
IN
OUT
G
D
IN
OUT
H
OUT
F
MUTI-RATE SDI INPUTS
IN
G
IN
OUT
E
IN
OUT
H
OUT
F
IN
OUT
D
IN
G
IN
OUT
E
IN
OUT
H
OUT
F
IN
OUT
D
IN
OUT
B
IN
OUT
C
IN
G
IN
OUT
E
IN
OUT
H
OUT
F
IN
OUT
D
IN
OUT
B
IN
OUT
IN
G
IN
OUT
E
H
OUT
F
IN
OUT
D
G
IN
OUT
E
IN
OUT
C
OUT
A
A
IN
B
A
OUT
IN
OUT
F
IN
OUT
D
C
OUT
A
OUT
IN
B
IN
OUT
C
OUT
A
OUT
IN
OUT
B
IN
OUT
IN
OUT
3
E
H
F
G
H
G
H
MUTI-RATE SDI OUTPUTS
G
H
A
B
MUTI-RATE SDI INPUTS
C
D
E
F
MUTI-RATE SDI OUTPUTS
REDUNDANT
100-240V
50/60Hz
2A MAX.
PRIMARY POWER SUPPLY
REDUNDANT POWER SUPPLY
5
PRIMARY
ANAHEIM, CA
100-240V
50/60Hz
2A MAX.
IN
6
Input 26
Input 28
Input 30
Input 32
Input 25
Input 27
Input 29
Input 31
Figure 2-1 — Arrangement of inputs and outputs on
the I/O boards
The board position designators correspond to the input and
output numbers served by that position (1 - 8, 9 - 16, and so on).
The location designators, A through H on each board correspond
to the transceiver modules, numbered from left to right, each of
which includes an input and an output.
See figure 2-1. The input and output numbers supported by the
I/O board in location 9 - 16 are as follows: A = 9, B = 10, C = 11,
D = 12, E = 13, F = 14, G = 15, and H = 16.)
2-2
IN
OUT
D
Slot 4
H
OUT
RS232/RS422
33 - 40
No board
installed
SDI/HD-SDI
Inputs 25-32
Outputs 25-32
IN
2
Slot 3
MUTI-RATE SDI INPUTS
OUT
Slot 2
Fiber optic
Inputs 9-16
Outputs 9-16
D
Output 11
LAN
Fiber optic
Inputs 1-8
Outputs 1-8
9 - 16
17 - 24
33 - 40
RS232/RS422
C
IN
OUT
A
25 - 32
LAN
REMOTE
IN
OUT
Slot 1
41 - 48
IN
OUT
25 - 32
4
1
49 - 56
IN
OUT
B
A
RESET
IN
OUT
C
B
IN
OUT
57 - 64
IN
OUT
IN
OUT
1-8
RESET
3
Input 1
Input 2
Input 3
Input 4
Output 1
Output 2
Output 3
Output 4
IN
IN
OUT
A
REMOTE
See figure 2-1. Each I/O board is identified by the input
and output numbers supported by the board position. The
transceiver modules on the I/O boards are identified as A
through H.
OUT
IN
OUT
Fiber Matrix 6400 Switcher • Installation
Refer also to the Fiber Matrix 6400 Switcher User’s Manual at www.extron.com.
6
Figure 2-2 — Fiber Matrix 6400 Switcher rear panel
a
b
c
d
e
f
Fiber optic connectors and LEDs — See page 2-4.
SDI/HDI-SDI BNC connectors — See page 2-5.
Ethernet connection (LAN connector) — See page 2-5.
Remote port — See page 2-5.
Power connectors — See page 2-5.
Power indicator LEDs — See page 2-5.
Fiber Matrix 6400 Switcher • Installation
Refer also to the Fiber Matrix 6400 Switcher User’s Manual at www.extron.com.
2-3
Installation, cont’d
Making connections
a
b
Fiber optic connectors and LEDs —
W This unit outputs continuous invisible light, which
may be harmful and dangerous to the eyes; use with
caution. For additional safety, plug the attached dust
caps into the optical transceivers when the fiber optic
cable is unplugged.
N Ensure that you use the proper fiber cable for your I/O
board. Typically, singlemode fiber has a yellow jacket and
multimode cable has an orange jacket.
N The Fiber Matrix 6400 uses one connector on the block as
an input and the second connector on the same block as a
separate output.
connector —
Ä Input
Connect a fiber optic
FOX 500 Tx
Transmitter
SDI Output connectors — Connect digital
É Multi-rate
displays to these BNC connectors.
c
Computer or control system connection — Wire the interface
cable as a crossover cable.
N The factory default IP address is 192.168.254.254.
d
OPTIONAL FOR
* RETURN
DATA
connector —
Å Output
Connect a fiber optic cable
5
1b
IN
OUT
Fiber Matrix
6400
Switcher
2-4
e
Power connector — Plug the switcher into two grounded AC
sources.
an uninterruptible power source or to a power source that
is completely independent from the primary power source.
f
Primary and Redundant power supply indicator LEDs —
Green — Indicates that the associated power supply is
operating within normal tolerances.
Red — Indicates that the associated power supply is operating
outside the normal tolerances or has failed. See chapter 5,
“Maintenance and Modifications“ to replace the power supply.
LINK
OPTICAL
2* 1
LINK
return, (receiver-to-transmitter)
function, connect the free end
to the Optical 2 connector
on a FOX 500 Tx
transmitter.
FOX 500 Rx
1a
N For reliability, connect the Redundant power cord to either
N Or, for the FOX 500 serial
Output LED — This LED is
always lit.
Pin RS-232 Function RS-422 Function
1
— Not used
—
Not used
2
TX Transmit
TX– Transmit (–)
3
RX Receive
RX– Receive (–)
6
4
— Not used
—
Not used
5
Gnd Ground
Gnd Ground
9
6
— Not used
—
Not used
7
— Not used
RX+ Receive (+)
8
— Not used
TX+ Transmit (+)
9
— Not used
—
Not used
Figure 2-6 — Audio output connector wiring
between each output LC
connector and a FOX 500 Rx or any
other compatible Extron FOX 500
device.
Remote port — If desired, connect a control system or computer
to the rear panel Remote RS-232/RS-422 port.
1
return, (receiver-to-transmitter)
function, connect the free end
to the Optical 2 connector on a
FOX 500 Rx receiver.
Input LED — When lit,
the link is active (light is
received).
Ethernet port — If desired, connect a network WAN or LAN
hub, a control system, or a computer to the Ethernet RJ-45 port.
Network connection — Wire as a patch (straight) cable.
N Or, for the FOX 500 serial
SDI Input connectors — Connect HD-SDI, SDI,
Ç Multi-rate
or 3G-SDI video inputs to these BNC connectors.
LINK
LINK
cable between each Input
LC connector and a
FOX 500 Tx or any other
compatible Extron FOX 500
device.
OPTICAL
1 2*
BNC connectors —
Receiver
OPTIONAL FOR
* RETURN
DATA
Fiber Matrix 6400 Switcher • Installation
Refer also to the Fiber Matrix 6400 Switcher User’s Manual at www.extron.com.
Fiber Matrix 6400 Switcher • Installation
Refer also to the Fiber Matrix 6400 Switcher User’s Manual at www.extron.com.
2-5
Installation, cont’d
Front Panel
Fiber Matrix 6400 Switcher
CONTROL
ENTER
PRESET
VIEW
ESC
CONFIG
POWER SUPPLY
PRIMARY
REDUNDANT
FIBER MATRIX 6400
FIBER OPTIC DIGITAL MATRIX SWITCHER
7
8
Figure 2-7 — Front panel configuration port
g
h
Configuration port — If desired, connect a control system
or computer to the front panel Configuration (RS-232) port.
Use an optional 9-pin D to 2.5 mm mini jack TRS RS-232
cable, part #70-335-01.
Primary and Redundant Power Supply LEDs —
Green — Indicates that the associated power supply is
operating within normal tolerances.
Red — Indicates that the associated power supply is operating
outside the normal tolerances or has failed. See chapter 4,
“Maintenance and Modifications”, to replace the power supply.
3
Chapter Three
Front Panel Operation
Creating a Tie
Viewing Ties (and Muting Outputs)
Saving or Recalling a Preset
Locking Out the Front Panel (Executive Mode)
2-6
Fiber Matrix 6400 Switcher • Installation
Refer also to the Fiber Matrix 6400 Switcher User’s Manual at www.extron.com.
Front Panel Operation
Creating a Tie
Saving or Recalling a Preset
1.
Press and release the Esc button to clear any input button,
output button, or control button indicators that may be lit.
2.
Press and release the desired input button.
1.
Save a
preset
The button lights to indicate the selection.
3.
4.
8
Recall a
preset
1.
toggle mute on and off, press and hold the output button
for 2 seconds.
2.
Press an input button. The buttons for all tied outputs
light.
3.
Press an output button. The buttons for the tied input and
all tied outputs light.
4.
Press the View button. All input and output buttons return
to an unlit state.
PRESET
The Preset button lights.
INPUTS
1 2 3 4 5 6 7
2.
Press and release the desired input or output button.
The button blinks red to indicate that
this preset is selected to save or recall.
Press the View button. Output buttons light for outputs
that have no ties established.
N If an output button blinks, that output is muted. To
PRESET
All input and output buttons with assigned presets light red.
When a preset is saved, the configuration data at
assigned preset locations will be overwritten.
The Enter button blinks to indicate
the need to confirm the change.
Viewing Ties (and Muting Outputs)
Preset button blinks.
Press and release.
ENTER
Press and release the Enter button. All button indicators
turn off.
PRESET
Recall a preset — Press and release the Preset button.
The output buttons blink to indicate the potential ties.
4
2 seconds
Press and hold.
Press and release the desired output button(s).
3
PRESET
5
Save a preset — Press and hold the Preset button until it
flashes.
1
3.
The Enter button blinks
red to indicate the need to
activate the save or recall.
ENTER
Press and release the Enter button.
Locking Out the Front Panel (Executive Mode)
To toggle the lock on and off, simultaneously press and hold the
Enter button and the Esc button for approximately 2 seconds.
Press and hold the Enter and
Esc buttons simultaneously to
toggle executive mode on or off.
C O NT R O L
ENTER PRESET
VIEW
C O NT R O L
ESC
2 seconds
ENTER PRESET
VIEW
ESC
The Preset and View buttons
blink twice to indicate the
mode change.
Release the buttons.
3-2
Fiber Matrix 6400 Switcher • Front Panel Operation
Refer also to the Fiber Matrix 6400 Switcher User’s Manual at www.extron.com.
Fiber Matrix 6400 Switcher • Front Panel Operation
Refer also to the Fiber Matrix 6400 Switcher User’s Manual at www.extron.com.
3-3
Front Panel Operation, cont’d
Fiber Matrix 6400 Switcher
4
Chapter Four
Remote Control
Selected SIS Commands
Installing and Starting the Control Program
Accessing the HTML Pages
3-4
Fiber Matrix 6400 Switcher • Front Panel Operation
Refer also to the Fiber Matrix 6400 Switcher User’s Manual at www.extron.com.
Remote Control
Selected SIS Commands
The switchers have Simple Instruction Set (SIS) commands that
you can use for operation and configuration. You can run these
commands from a PC connected to either of the switcher’s serial
ports or the Ethernet port. See c, d, and g, on pages 2-5 and
2-6, for connection information.
Establishing a network (Ethernet) connection
N If you connect to the switcher via the LAN port, and it
is the first time you have done so, you may change the
controller’s default settings (IP address, subnet mask,
and [optional] administrator name and password). See
"Configuring for Network Communication" for details.
Establish a network connection as follows:
1.
Open a TCP socket to port 23 using the switcher’s IP
address.
N The factory default IP address is 192.168.254.254.
The switcher responds with a copyright message including
the date, the name of the product, the firmware version,
the part number, and the current date/time.
N If the switcher is not password-protected, the device is now
ready to accept SIS commands.
If the switcher is password-protected, a password
prompt appears.
2.
If the switcher is password-protected, enter the appropriate
password.
If the password is accepted, the switcher responds with
Login User or Login Administrator.
If the password is not accepted, the Password prompt
reappears.
Number of connections
A switcher can have up to 200 simultaneous TCP connections,
including all HTTP sockets and Telnet connections. When
the connection limit is reached, the switcher accepts no new
connections until some have been closed. No error message or
indication is given that the connection limit has been reached.
To maximize performance of your switcher, the number of
connections should stay low and unnecessary open sockets
should be closed.
Verbose mode
Telnet connections to a switcher can be used to monitor
for changes that occur on the switcher, such as front panel
operations and SIS commands from other Telnet sockets or a
serial port. For a Telnet session to receive change notices from
the switcher, the Telnet session must be in verbose mode 3. See
the Set verbose mode command on page 4-7. In verbose
mode 3, the Telnet socket reports changes in messages that
resemble SIS command responses.
Host-to-switcher instructions
The switcher accepts SIS commands through either serial port.
SIS commands consist of one or more characters per command
field. They do not require any special characters to begin or end
the command character sequence. Each switcher response to an
SIS command ends with a carriage return and a line feed (CR/
LF = ]), which signals the end of the response character string.
A string is one or more characters.
N The table that begins on the next page is a partial list
of SIS commands. For a complete listing, refer to the
Fiber Matrix 6400 Switcher User's Manual.
Connection timeouts
The Ethernet link times out and disconnects after a designated
period of no communication. By default, this timeout value
is set to 5 minutes, but the value can be changed. See the
Configure port timeout SIS commands on page 4-7.
N Extron recommends leaving the default timeout at
5 minutes and periodically issuing the Query (Q)
command to keep the connection active or disconnecting
the socket and reopening the connection when necessary.
4-2
Fiber Matrix 6400 Switcher • Remote Control
Refer also to the Fiber Matrix 6400 Switcher User’s Manual at www.extron.com.
Fiber Matrix 6400 Switcher • Remote Control
Refer also to the Fiber Matrix 6400 Switcher User’s Manual at www.extron.com.
4-3
ASCII command
(host to switcher)
Response
(switcher to host)
Additional description
Create ties
Refer also to the Fiber Matrix 6400 Switcher User’s Manual at www.extron.com.
Fiber Matrix 6400 Switcher • Remote Control
N • Commands can be entered back-to-back in a string, with no spaces. For example: 1*1!02*02&003*003%4*24$.
•The matrix switchers support 1-, 2-, and 3-digit numeric entries (1*1!, 02*02&, or 003*003%).
N The ! tie command, the & tie command, and the % tie command can be used interchangeably.
N The ! read tie command, & read tie command, and the % read tie command can be used interchangeably.
Tie input X! to output [email protected]
Example (see Note, above):
X!*[email protected]!
1*3!
[email protected]•InX!•All]
Tie input X! to output [email protected]
Example (see Note, above):
X!*[email protected]&
10*4&
[email protected]•InX!•RGB]
Tie input X! to output [email protected]
Example (see Note, above):
X!*[email protected]%
[email protected]•InX!•Vid]
7*5%
Out05•In07•Vid]
[email protected]&
[email protected]%
[email protected]!
X!]
X!]
X!]
Read output tie
Read output tie
Read output tie
N
X! = Input number
[email protected] = Output number
Command
Out03•In01•All]
Out04•In10•RGB]
Tie input X! to output [email protected]
Tie input 1 to output 3.
Tie input X! to output [email protected]
Tie input 10 to output 4.
Tie input X! to output [email protected]
Tie input 7 to output 5.
Input X! is tied to output [email protected]
Input X! is tied to output [email protected]
Input X! is tied to output [email protected]
00 – (maximum number of inputs for your configuration) (00 = untied)
01 – (maximum number of outputs for your configuration)
ASCII command
Response
Additional description
(host to switcher)
(switcher to host)
Channel mute
[email protected]*1B
[email protected]*1]
Mute output [email protected] (no signal is output, but
the light output remains active).
Channel unmute
[email protected]*0B
[email protected]
[email protected]*0]
Read channel mute
Unmute output [email protected] (signal is output).
1 = mute on, 0 = mute off.
Global channel mute
1*B
Global channel unmute
0*B
View output mutes
EVM}
Channel mute commands
Fiber Matrix 6400 Switcher • Remote Control
Refer also to the Fiber Matrix 6400 Switcher User’s Manual at www.extron.com.
X#]
Vmt1]
Vmt0]
X#1, X#2, ... X#n]
Mute all audio outputs.
Unmute all audio outputs.
Each X# response is the mute status of an
output, starting from output 1.
n = the maximum number of outputs for
your configuration.
Save and recall presets
N If you try to recall a preset that is not saved, the matrix switcher responds with the error code E11.
Save current configuration as a
Command character is a comma.
X$,
SprX$]
global preset
Example:
Save current ties as preset 9.
Spr09]
9,
Recall a global preset
Example:
N
[email protected] = Output number
X# = Mute
X$ = Global or room preset #
X$.
5.
RprX$]
Command character is a period.
Rpr05]
Recall preset 5, which becomes the current
configuration.
01 – (maximum number of outputs for your model)
0 = not muted, 1 = muted
00 - 64
Remote Control, cont’d
4-4
Command
4-5
Fiber Matrix 6400 Switcher • Remote Control
Lock all front panel functions
1X
Exe1]
Enable Lock mode 1.
Unlock all front panel functions
0X
Exe0]
Enable Lock mode 0.
View lock status
X
X%]
I
VX^XX&•AX^XX& •SX*1X*2...X*8]
ASCII command
(host to switcher)
Response
Additional description
(switcher to host)
Front panel lock (executive mode)
Refer also to the Fiber Matrix 6400 Switcher User’s Manual at www.extron.com.
Information requests
Information request
VX^XX& shows the number of available
inputs and outputs for this configuration.
AX^XX& has no meaning for this product.
SX*1X*2...X*8 shows the board type
installed in each slot.
Request part number
N
60-878-01]
Query controller firmware version
Q
X(]
1.23]
Example:
N
Q
The factory-installed controller firmware
version is 1.23 (sample value only).
X% = Lock mode
0 = unlocked
1 = locked
X^ = Inputs
Total number of inputs for this switcher
X& = Outputs
Total number of outputs for this switcher
X* = Board installed
0 = No board installed
1 = 8x8 multimode board
2 = 8x8 singlemode board
3 = SDI/HD-SDI board
x = Unknown board or mix of transceivers installed
X( = Firmware version number to second decimal place (x.xx)
Command
ASCII command
Response
(host to switcher)
(switcher to host)
EX1)CI}
ECI}
EX1)CS}
ECS}
EX1)CG}
ECG}
EX1!DH}
EDH}
[email protected]}
ECV}
E0*X1#TC}
E0TC}
E1*X1#TC}
E1TC}
IpiX1)]
X1)]
IpsX1)]
X1)]
IpgX1)]
X1)]
IdhX1!]
X1!]
[email protected]]
[email protected]]
Pti0*X1#]
X1#]
Pti1*X1#]
X1#]
Additional description
IP setup
Set IP address
Fiber Matrix 6400 Switcher • Remote Control
Refer also to the Fiber Matrix 6400 Switcher User’s Manual at www.extron.com.
Read IP address
Set subnet mask
Read subnet mask
Set gateway IP address
Read gateway IP address
Set DHCP on or off
Read DHCP on/off status
Set verbose mode
Read verbose mode
Configure current port timeout
Read current port timeout
Configure global IP port timeout
Read global IP port timeout
N
X1) = IP address
X1! = DHCP
[email protected] = Verbose mode
X1# = Port timeout interval
###.###.###.###
0 =1 off, 1 = on
0 = clear/none (default for Telnet connection)
1 = verbose mode (default for RS-232/RS-422 connection)
2 = tagged responses for queries
3 = verbose mode and tagged for queries
1 (= 10 seconds) - 65000 (default is 30 = 300 seconds = 5 minutes)
Remote Control, cont’d
4-6
Command
4-7
Remote Control, cont’d
Installing and Starting the Control Program
4.
Another way to operate the switcher is via the Windows -based
Matrix Switchers Control Program. This program is contained
on the Extron Software Products DVD (included with the
switcher). Run this program on a PC connected to either of the
switcher’s serial ports or the Ethernet port. See c, d, and g,
on pages 2-5 and 2-6, for connection information. The program
must be installed on a Windows-based computer and cannot be
run from the DVD.
®
N For details on operating the program, refer to the
Fiber Matrix 6400 Switcher User's Manual, chapter 5,
“Matrix Software”.
•
•
•
•
Insert the DVD into the drive. The installation program
should start automatically.
The Extron software DVD window appears.
MATRIX Switcher+ Control Program
MATRIX Switcher+ Help
Uninstall MATRIX Switcher
Check for Matrix Updates
Starting the program
N If you connect to the switcher via the LAN port, and it
is the first time you have done so, you may change the
controller’s default settings (IP address, subnet mask,
and [optional] administrator name and password). See
"Configuring for Network Communication" for details.
Installing the program
1.
Follow the on-screen instructions. The installation
program creates a C:\Program Files\Extron\
Matrix_Switchers directory and an “Extron Electronics\
Matrix Switchers” group folder. It installs the following
four programs:
1.
Click Start > Programs > Extron Electronics > Matrix
Switchers > MATRIX Switcher + Control Pgm.
The Comm Port Selection window appears.
N If the installation program does not self-start, run
Launch.exe from the DVD.
2.
Click the Software tab.
3.
Scroll to the Matrix Switchers program and click
Install.
2.
N For a comm port, check the baud
rate displayed in the Comm Port
Selection window. If you need to
change the baud rate, click the Baud
button and double-click the desired
baud rate.
4-8
Fiber Matrix 6400 Switcher • Remote Control
Refer also to the Fiber Matrix 6400 Switcher User’s Manual at www.extron.com.
Choose the comm (serial) port that is connected to the
switcher or IP [LAN].
Click OK.
If you selected a serial port in step 2, the Matrix Switchers
Control Program is ready for operation.
Fiber Matrix 6400 Switcher • Remote Control
Refer also to the Fiber Matrix 6400 Switcher User’s Manual at www.extron.com.
4-9
Remote Control, cont’d
3.
If you selected IP [LAN] in step 2, the IP Connection
window appears.
Accessing the HTML Pages
Another way to operate the switcher is via its factory-installed
HTML pages, which are always available and cannot be erased
or overwritten. The switcher’s HTML pages are accessible
through its LAN port, connected via a LAN or WAN, using a
Web browser such as Microsoft Internet Explorer. See g, on
page 2-6, for connection information.
Configuring for Network Communication
a. Examine the Matrix IP Address field, which displays
the last Matrix IP address entered.
If necessary, enter the correct IP address in the field.
N 192.168.254.254 is the factory-specified default value for
this field.
b. If the switcher is password-protected, enter the
appropriate administrator or user password in the
Password field.
The first time you connect a PC to a switcher via its LAN port,
you may need to temporarily change the PC’s IP settings in
order to communicate with the controller. Then you must
change the controller’s default settings (IP address, subnet mask,
and [optional] administrator name and password) in order to
use the unit on an intranet (LAN) or on the Internet. After you
have set up the Fiber Matrix 6400 for network communication,
you can reset the PC to its original network configuration.
N The computer and the switcher must both be connected
to the same subnet on a LAN (using a straight-through
cable). Alternatively, you can use a crossover Ethernet
cable to connect the controller directly to the computer.
c. Click Connect. The Matrix Switchers Control Program
is ready for operation.
Use the ARP command to configure the IP address as follows:
1.
Obtain a valid IP address for the Fiber Matrix 6400 from
the network administrator.
2.
Obtain the switcher’s MAC address (UID #) from the label
on its rear panel. The MAC address should have this
format: 00-05-A6-xx-xx-xx.
3.
If the switcher has never been configured and is still
set for factory defaults, go to step 4. If not, perform
a Mode 4 system reset. For detailed information
on reset modes, see “Rear Panel Operations” in the
Fiber Matrix 6400 Switcher User’s Manual.
N The switcher must be configured with the factory default
IP address (192.168.254.254) before the ARP command is
executed, as described below.
4-10
Fiber Matrix 6400 Switcher • Remote Control
Refer also to the Fiber Matrix 6400 Switcher User’s Manual at www.extron.com.
Fiber Matrix 6400 Switcher • Remote Control
Refer also to the Fiber Matrix 6400 Switcher User’s Manual at www.extron.com.
4-11
Remote Control, cont’d
4.
At the PC, access the MS-DOS® command prompt, then
enter the arp –s command. Type in the desired new
IP address for the unit (obtained in step 1) and the unit’s
MAC address (from the unit's rear panel). For example:
arp –s 10.13.197.7 00-05-A6-03-69-B0 and then
press {Enter}.
After receiving the arp -s command, the controller
changes to the new address and starts responding to the
ping requests, as described in step 5.
N You must ping the Fiber Matrix 6400 as shown in step 5
for the IP address change to take place. The response should
show the new IP address, as shown in the following figure.
5.
Execute a ping command by entering “ping” followed by
a space and the new IP address at the command prompt. For example:
ping 10.13.197.7
Loading the start-up page
N If your Ethernet connection to the matrix switcher is
unstable, try turning off the proxy server in your Web
browser. In Microsoft Internet Explorer, click Tools >
Internet Options > Connections > LAN Settings,
uncheck the Use a proxy server... box, and then click OK.
N For details on operating the switcher via HTML pages,
refer to the Fiber Matrix 6400 Switcher User's Manual,
chapter 6, “HTML Operation”.
1.
Start the Web browser program.
2.
Click in the browser’s Address field.
3.
Enter the Matrix IP address in the browser’s Address field.
N 192.168.254.254 is the factory-specified default value for
this field.
4.
Press the keyboard Enter key. The switcher checks to see if
it is password-protected.
If the switcher is not password-protected, it checks and
downloads the HTML start-up page. The switcher is ready
for operation via HTML remote control.
If the switcher is password-protected, it downloads the
Enter Network Password page.
C:\>ping 10.13.197.7
Pinging 10.13.197.7 with 32 bytes of data:
Reply
Reply
Reply
Reply
from
from
from
from
10.13.197.7:
10.13.197.7:
10.13.197.7:
10.13.197.7:
bytes=32
bytes=32
bytes=32
bytes=32
time<10ms
time<10ms
time<10ms
time<10ms
TTL=128
TTL=128
TTL=128
TTL=128
Ping statistics for 10.13.197.7:
Packets: Sent = 4, Received = 4, Lost = 0 (0% loss),
Approximate round trip times in milli-seconds:
Minimum = 0ms, Maximum = 0ms, Average = 0ms
N You can reconnect using either Telnet or a Web browser to
verify that the update was successful.
4-12
6.
After verifying that the IP address change was successful,
enter and issue the “arp –d” command at the DOS prompt. For example:
arp –d 10.13.197.7 removes 10.13.197.7 from the ARP
table
or
arp –d* removes all static IP addresses from the ARP
table.
Fiber Matrix 6400 Switcher • Remote Control
Refer also to the Fiber Matrix 6400 Switcher User’s Manual at www.extron.com.
N A User name entry is not required.
5.
Enter the appropriate administrator or user password in
the Password field and click OK.
6.
The switcher downloads the HTML start-up page. The
switcher is ready for operation via HTML remote control.
Fiber Matrix 6400 Switcher • Remote Control
Refer also to the Fiber Matrix 6400 Switcher User’s Manual at www.extron.com.
4-13
Remote Control, cont’d
Fiber Matrix 6400 Switcher
5
Chapter Five
Maintenance and Modifications
Removing and Installing an I/O Board or Blank Panel
Removing and installing a Power Supply Module
4-14
Fiber Matrix 6400 Switcher • Remote Control
Refer also to the Fiber Matrix 6400 Switcher User’s Manual at www.extron.com.
Maintenance and Modifications
Removing and Installing an I/O Board or Blank
Panel
W The Fiber Matrix 6400 fiber optic I/O boards output
continuous invisible light, which may be harmful and
dangerous to the eyes; use with caution.
• Do not look into the rear panel fiber optic
cable connectors or into the fiber optic cables
themselves.
• Plug the attached dust caps into the optical
transceivers when the fiber optic cable is
unplugged.
Remove and replace and I/O board or blank panel as follows:
N The I/O boards are hot-swappable. You do not need to
power down the switcher to remove an I/O board.
1.
For an I/O board, disconnect any connected cables.
2.
Rotate the left and right knurled knobs to completely
loosen the captive screws.
3.
Gently pull on the knurled knobs/captive screws to loosen
the board or panel from the backplane.
4.
Slide the board or panel out of the chassis (below).
C Do not touch the electronic components or the
connectors on the backplane or on the circuit boards
without being electrically grounded. Handle circuit
boards by their edges only. Electrostatic discharge can
damage circuits, even if you cannot feel, see, or hear it.
N As factory configured, the fiber optic I/O boards are
configured as either 100 percent singlemode or 100 percent
multimode, but you can remove a fiber optic transceiver
module (one input and one output) of one transmission
mode and replace it with a block of the other transmission
mode.
You can mix transmission mode transceiver modules on
a fiber optic I/O board, provided that you ensure that
each fiber cable and connected devices are the appropriate
transmission mode for the transceiver module.
Align with
plastic guides.
IN
T
OU
H
IN
IN
Typically, singlemode fiber has a yellow jacket and
multimode cable has an orange jacket.
T
OU
T
OU
G
IN
H
IN
IN
T
OU
T
OU
F
IN
T
OU
G
IN
T
OU
IN
T
OU
E
T
OU
T
OU
F
IN
G
IN
IN
N For proper cooling and air flow, boards and/or blank panels
should be installed in all locations during normal switcher
operations.
IN
T
OU
T
OU
1-8
9 - 16
ACT LINK
LAN
17 - 24
G
IN
T
T
OU
T
OU
F
IN
G
IN
C
IN
D
IN
LY
IN
IN
T
F
WER
T PO
T
SU
IN
AN
ND
T
OU
E
C
IN
E
PP
OU
OU
B
DU
T
OU
RE
D
IN
T
IN
IN
T
OU
33 - 40
the different arrangement of connectors on the various I/O
boards.
C
IN
T
IN
D
IN
OU
T
OU
41 - 48
B
IN
IN
IN
C
LY
PP
T
OU
49 - 56
A
IN
B
C
T
OU
T
OU
A
T
OU
D
T
OU
T
OU
B
IN
F
T
OU
T
OU
E
OU
A
G
T
OU
IN
OU
T
OU
T
IN
IN
H
IN
OU
IN
T
OU
A
T
OU
OU
T
OU
E
D
IN
T
OU
B
T
25 - 32
IN
T
OU
C
IN
T
OU
IN
OU
N See "A note on I/O boards", on page 2-2, to understand
D
T
OU
B
IN
A
T
OU
F
IN
H
IN
IN
T
T
OU
A
T
OU
OU
H
IN
T
OU
E
C
IN
T
OU
T
SE
IN
T
OU
G
IN
T
OU
RE
IN
T
F
IN
IN
T
OU
E
T
IN
H
IN
T
OU
D
OU
B
T
OU
G
IN
T
IN
T
OU
IN
T
OU
F
IN
OU
C
IN
T
OU
E
D
T
OU
IN
H
IN
T
OU
T
OU
IN
H
IN
WER
Y PO
AR
IM
PR
B
T
SU
OU
A
IN
T
57 - 64
OU
Circuit boards can be replaced to accomodate SDI/HD-SDI
(electric) signals. They can be added or removed to increase or
decrease the I/O configuration (size) of the Fiber Matrix.
A
Tz
AN
60H
ND
DU 50/
RE 0V MAX.
-24 A
100 1.2
Y z
AR 60H
IM 50/
PR0V X.
-24 A MA
100 1.2
EIM,
CA
AH
AN
5-2
Fiber Matrix 6400 Switcher • Maintenance and Modifications
Refer also to the Fiber Matrix 6400 Switcher User’s Manual at www.extron.com.
Knurled
Knobs
5.
Place the removed board on an anti-static surface or in an
anti-static container.
6.
For an I/O board, orient the board to be installed so
that transceiver module A (fiber board) or input BNC A
(SDI/HD-SDI board) is on the left and transceiver module
or output BNC H is on the right.
7.
For an I/O board, align the board with the left and right
chassis guides (above).
Fiber Matrix 6400 Switcher • Maintenance and Modifications
Refer also to the Fiber Matrix 6400 Switcher User’s Manual at www.extron.com.
5-3
Maintenance and Modifications, cont’d
8.
Gently slide the board or blank panel into the enclosure.
For an I/O board, slide the board toward the front panel
until it meets resistance.
9.
Gently seat the board or panel in the backplane.
10. Tighten the left and right knurled knobs/captive screws to
lock the board or panel in place.
N If necessary, use a screwdriver to tighten the knurled
knobs/captive screws.
IN
T
OU
H
IN
IN
T
OU
T
OU
Removing and Installing a Power Supply
Module
H
IN
IN
T
OU
T
OU
F
IN
G
IN
IN
T
OU
T
OU
E
T
OU
F
IN
G
IN
IN
E
1-8
LAN
17 - 24
25 - 32
IN
OU
E
C
IN
RE
D
IN
T
OU
PLY
UP
RS
E
OW
TP
N
DA
N
DU
T
B
IN
F
T
OU
T
IN
T
OU
T
OU
33 - 40
T
OU
E
OU
A
G
IN
T
OU
IN
T
OU
F
IN
IN
D
IN
T
OU
T
OU
C
IN
H
IN
D
IN
T
OU
B
IN
G
IN
T
OU
E
C
IN
T
OU
A
T
OU
T
OU
F
IN
T
OU
T
B
IN
T
OU
IN
T
OU
E
D
IN
H
IN
T
OU
A
9 - 16
ACT LINK
ET
G
T
OU
OU
IN
T
OU
RES
F
T
OU
C
IN
T
OU
T
OU
IN
IN
B
IN
T
OU
IN
T
OU
IN
D
IN
T
H
IN
T
OU
E
C
G
IN
T
OU
OU
T
OU
F
IN
IN
IN
T
OU
T
OU
T
OU
IN
T
OU
D
IN
T
OU
H
IN
T
OU
T
OU
H
IN
T
OU
T
OU
A
B
IN
C
IN
D
IN
T
OU
T
OU
T
41 - 48
OU
A
B
IN
IN
T
OU
49 - 56
The two power supply modules (primary power supply and
redundant power supply) are identical and hot-swappable.
Each power supply module has a 2-color LED, visible on
the rear panel, that indicates the status of the power supply
outputs. If the LED is lit green, the power supply is operating
normally. If the LED is lit red, the supply has failed and should
be replaced at the earliest opportunity.
G
IN
T
OU
N The power supply modules are hot-swappable. Either
C
E
OW
B
IN
YP
AR
IM
PR
57 - 64
T
OU
power supply can be removed without powering down the
switcher. You do not need to power down the switcher to
install a power supply.
A
T
AN Hz
ND /60
DU 50
RE40V MAX.
0-2 A
1.2
10
Y
PLY
UP
RS
T
OU
A
Align with
plastic guides.
Hz
AR
IM 50/60
PRV X.
40 MA
0-2 A
1.2
10
1.
Rotate the left and right knurled knobs to completely
loosen the captive screws.
2.
Gently pull on the handle to loosen the power supply from
the backplane.
3.
Slide the power supply out of the chassis.
4.
Orient the power supply module to be installed with the
LED to the right.
5.
Align the flanges on the power supply module with the
left and right power supply guides (see the next page).
6.
Gently slide the power supply module into the enclosure
until the power supply meets resistance.
7.
Gently seat the power supply in the backplane.
8.
Tighten the left and right knurled knobs/captive screws to
lock the power supply in place.
A
EI
AH
AN
C
M,
Power
LED
Knurled
Knobs
N If necessary, use a screwdriver to tighten the knurled
knobs/captive screws.
5-4
Fiber Matrix 6400 Switcher • Maintenance and Modifications
Refer also to the Fiber Matrix 6400 Switcher User’s Manual at www.extron.com.
Fiber Matrix 6400 Switcher • Maintenance and Modifications
Refer also to the Fiber Matrix 6400 Switcher User’s Manual at www.extron.com.
5-5
Maintenance and Modifications, cont’d
5-6
Fiber Matrix 6400 Switcher • Maintenance and Modifications
Refer also to the Fiber Matrix 6400 Switcher User’s Manual at www.extron.com.
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement