advertisement
BUILT-IN SINGLE ZONE WINE CELLAR
WKEes 553
BUILT-IN SINGLE ZONE WINE CELLAR WKEes 553
3 Year
Warranty
Model
Type I Category
Finish
°Energy consumption (kWh/yr) I 24hr
Bottle capacity (750ml Bordeaux)
Safety glass door
MagicEye control system I Display
Digital temperature display
Tinted glazed door
WKEes 553
BI I GrandCru
Stainless Steel
°130 I 0.4
18
•
SoftTouch I LCD
Internal
Double
Temperature zones
Temperature range (°C) Min I Max °C
1
5 I 20
Suitable for ambient temperature MinIMax°C 10 I 32
Interior light Dimmable LED
Hand crafted beech wood shelves
Shelves mounted on telescopic rails
Base shelves
Recirculated air cooling
Fresh air supply via activated charcoal filter 1
2
•
1
•
Child proof lock (control panel)
Reversible door hinges
Compressors
Door open warning signal
1
•
•
•
Temperature alarm
Malfunction warning signal
Ventilation switch
Automatic defrosting
Technical Information
•
•
•
•
Default hinge
Gross weight (kg) I Net weight (kg)
Height (mm)
Width (mm)
Depth (mm)
Voltage (V) I Rated Input Power (W)
Made In
Right
32 I 30
450
560
550
220-240 I 120
Austria
KEY: BI = Built-In, ° = Measurements taken at +25°C ambient and +12°C interior temperature tested by Liebherr Germany (not to Australian standards),
= Based on Bordeaux 750ml bottle - capacity may vary depending on bottle shape and size. Door hinging either right or left hand must be nominated for this model.
WKEes 553
Millimetres (mm)
Whilst every effort is made to ensure all specifications and information in this flyer are correct at time of printing, Andi-Co Australia Pty. Ltd. reserve the right to make changes without notification. Where actual appliance measurements, specifications and ratings are crucial, we recommend that the actual appliance installation instructions that accompany each appliance be checked. Andi-Co Australia will not be liable for any loss.
HEAD OFFICE: 1 Stamford Road Oakleigh Vic 3166, T: 1800 685 899, E: [email protected], W: www.andico.com.au
LPF05112015
Important Information
ATTENTION:
CABINET MAKER / INSTALLER / BUILDERS
IMPORTANT INFORMATION ABOUT VENTILATION FOR INTEGRATED APPLIANCES
Following the installation instructions that accompany a Liebherr integrated appliance is extremely important. Ventilation is imperative for the correct operation of Liebherr integrated appliances. It is essential that installers ensure minimum ventilation is provided in accordance with the installation manual that accompanies the actual appliance. Appliance faults resulting from incorrect installation or inadequate ventilation may not be covered by warranty. Please read the below information for a brief overview of installing integrated appliances.
Installation
• In a multiple unit installation each unit must be installed in a separate cabinet.
• Maximum cabinet and door panel thickness is 19mm (where applicable).
• The doors of units with two doors must not be joined together with a single joinery panel (where applicable).
• Joinery door panels must not exceed the admissible weight of the unit door (where applicable).
Ventilation
• Minimum 200cm 2 ventilation openings must be provided at both top and bottom of cabinet.
• The ventilation path must maintain a minimum cross-section of 200cm 2 flow and return into the room.
• Room must be a habitable room (excluding bedrooms) of not less than 50m 3 volume.
• When fitted, each ventilation grill must have a minimum open area of 200cm 2 .
• Ventilation openings provided for other appliances must not adversely affect the refrigeration unit ventilation.
• Failure to provide adequate ventilation can damage the appliance.
General Installation Information
• Power outlet must be accessible. Do not install within the unit cabinet.
• Water supply point must be accessible. Do not install within the unit cabinet.
• Standard water hose length 1.5m. Selected models feature 3.0m hoses. Check specification table for further details.
• 3.0m water hose is available from Andi-Co Australia spare parts at an additional cost.
Operating and installation instructions are available on our website www.andico.com.au. Please note that changes may occur without notice therefore where actual appliance measurements and specifications are crucial, we recommend that the actual appliance installation instructions that accompany the appliance be used.
Design Review Service
Don’t void the appliance warranty with inadequate ventilation. Andi-Co Australia offer a design review service. Send your cabinet plans to [email protected] for assessment. We can assist in identifying any deficiencies in the cabinet and ventilation design before you build. Attachments should be in pdf format and include the unit model number/s and ventilation grill specifications.
Ventilation Grills
To ensure adequate ventilation for your Liebherr appliance, it is paramount to install the right ventilation grills. For ventilation grill recommendations please contact Liebherr customer care on 1300 650 020.
Suitable for models requiring 200cm
2
airflow only
Part No.: YL7427640
Suitable for integrated appliances requiring minimum airflow 200cm 2
61
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project