Siemens | Gigaset CE450 IP R | Specifications | Siemens Gigaset CE450 IP R Specifications

Siemens Gigaset CE450 IP R Specifications
BA Cover CE460IP R.qxd
26.01.2007
11:52 Uhr
Seite 1
Issued by
Siemens Home and Office Communication Devices GmbH & Co. KG
Schlavenhorst 66
D-46395 Bocholt
© Siemens Home and Office Communication Devices GmbH & Co. KG 2007
All rights reserved. Subject to availability.
Rights of modification reserved.
www.siemens.com/gigaset
Gigaset
CE460 IP R
cyan magenta yellow black
Liebreich Medienproduktion
CE 450 IP R / IM-Ost english / A31008-M1817-R601_1-7619 / overview.fm / 02.03.2007
The handset at a glance
The handset at a glance
Handset keys
1
14
¨
V
11.01.07
§§§§§§INT§§§§§
11:56
§§§§Menu§
2
3
4
6
12
13
5
10
11
9
7
8
The base station at a glance
1 Display in idle status (example)
2 Battery charge status
e V U (1/3 charged to fully
charged)
= flashes: battery almost flat
e V U flashes: battery charging
3 Control key (page 31)
4 Display keys (page 32)
5 End call key, On/Off key
End call, cancel function, go back one menu
level (press briefly), back to idle status (press
and hold), activate/deactivate handset
(press and hold in idle status)
6 Message key
Access calls list
Flashes: new call
7 Hash key
Keypad lock on/off (press and hold,
page 31)
Toggle between upper/lower case letters
and digits for text entry (page 124)
8 Microphone
9 Star key
Ringer tones on/off (press and hold in idle
status)
10 Connection socket for headset (page 22)
11 Key 1 (press and hold)
Fast access to network mailbox (page 47)
12 Handsfree key
Switch between earpiece and handsfree
mode, open last number redial list (press in
idle status)
Lights up: handsfree talking activated
Flashes: incoming call
13 Talk key
Accept a call, open last number redial list
(press in idle status)
14 Signal strength
¦ § ¨ (low to high)
¥ flashes: no reception
Base station key
Version 2, 21.12.2006
1 Paging key
Lights up: base station is connected with the
mains power supply
Flashes: data transfer to LAN/WAN connection
Press briefly: start paging (page 50)
Press and hold:
set base station to registration mode to register the handset (page 48)
1
1
CE 450 IP R / IM-Ost english / A31008-M1817-R601_1-7619 / CE450IP_R_laenderIVZ.fm / 02.03.2007
Contents
Contents
VoIP telephony via Gigaset.net
The handset at a glance . . . . . . . . 1
The base station at a glance . . . . 1
Safety precautions . . . . . . . . . . . . 4
Gigaset CE 460 IP R – more than
just a telephone . . . . . . . . . . . . . . 5
VoIP – making calls via
the Internet . . . . . . . . . . . . . . . . . . 6
Base station components . . . . . . . 6
First steps . . . . . . . . . . . . . . . . . . . . 8
Pack contents . . . . . . . . . . . . . . . . . . . . 8
Setting up the handset for use . . . . . . . 8
Installing the base station . . . . . . . . . 11
Connecting the base station . . . . . . . 12
Configuring the Internet connection on
the base station router . . . . . . . . . . . . 15
Making settings for VoIP telephony on
the base station phone . . . . . . . . . . . 17
Belt clip and headset . . . . . . . . . . . . . 22
Menu trees . . . . . . . . . . . . . . . . . . 23
Phone menu . . . . . . . . . . . . . . . . . . . . 23
Router Web configurator menu . . . . . 26
Phone Web configurator menu . . . . . 27
Making calls . . . . . . . . . . . . . . . . . 28
Making an external call . . . . . . . . . . .
Ending a call . . . . . . . . . . . . . . . . . . . .
Accepting a call . . . . . . . . . . . . . . . . .
Call display . . . . . . . . . . . . . . . . . . . . .
Handsfree talking . . . . . . . . . . . . . . . .
Muting the handset . . . . . . . . . . . . . .
28
28
29
29
30
30
Version 2, 21.12.2006
Operating the handset . . . . . . . . 31
Activating/deactivating the handset .
Activating/deactivating the
keypad lock . . . . . . . . . . . . . . . . . . . . .
Control key . . . . . . . . . . . . . . . . . . . .
Display keys . . . . . . . . . . . . . . . . . . . .
Reverting to idle status . . . . . . . . . . . .
Menu guidance . . . . . . . . . . . . . . . . .
Correcting incorrect entries . . . . . . . .
2
31
31
31
32
32
33
33
34
Searching for subscribers in the
Gigaset.net directory . . . . . . . . . . . . . 34
Calling a Gigaset.net subscriber . . . . . 37
Network services - VoIP . . . . . . . 38
Settings for all calls . . . . . . . . . . . . . . . 38
Functions during a call . . . . . . . . . . . . 39
Using the directory and lists . . 40
Directory . . . . . . . . . . . . . . . . . . . . . . . 40
Last number redial list . . . . . . . . . . . . 43
Opening lists with the message key . . 44
Using the network mailbox . . . 47
Configuring the network mailbox for fast
access . . . . . . . . . . . . . . . . . . . . . . . . . 47
Network mailbox message . . . . . . . . . 47
Using several handsets . . . . . . . 48
Registering handsets . . . . . . . . . . . . . .
De-registering handsets . . . . . . . . . . .
Changing a handset's internal number
Changing the name of a handset . . . .
Locating a handset ("paging") . . . . . .
Making internal calls . . . . . . . . . . . . . .
48
49
49
50
50
50
Handset settings . . . . . . . . . . . . 52
Changing the display language . . . . .
Setting the display . . . . . . . . . . . . . . .
Activating/deactivating auto answer .
Adjusting the loudspeaker volume . . .
Changing ringer tones . . . . . . . . . . . .
Advisory tones . . . . . . . . . . . . . . . . . .
Using the handset as an alarm clock .
Restoring the handset to the factory
settings . . . . . . . . . . . . . . . . . . . . . . . .
52
52
53
53
53
54
55
56
Setting the base station . . . . . . 56
Changing the system PIN of the base
station phone . . . . . . . . . . . . . . . . . . . 56
Restoring the base station to the factory
settings . . . . . . . . . . . . . . . . . . . . . . . . 56
Activating/deactivating the on
hold music . . . . . . . . . . . . . . . . . . . . . . 57
Activating/deactivating
repeater mode . . . . . . . . . . . . . . . . . . 58
Updating the base station phone's
firmware . . . . . . . . . . . . . . . . . . . . . . . 58
CE 450 IP R / IM-Ost english / A31008-M1817-R601_1-7619 / CE450IP_R_laenderIVZ.fm / 02.03.2007
Contents
Making VoIP settings . . . . . . . . . 59
Phone Web configurator . . . . . . 85
Setting the base station phone's IP address
in LAN . . . . . . . . . . . . . . . . . . . . . . . . . 59
Entering/changing the first VoIP account
with the connection assistant . . . . . . 61
Entering/changing the first VoIP account
without the connection assistant . . . 61
Activating/deactivating display of VoIP
status codes . . . . . . . . . . . . . . . . . . . . 63
Checking the base station phone's MAC
address . . . . . . . . . . . . . . . . . . . . . . . . 63
Connecting the PC to the phone Web
configurator . . . . . . . . . . . . . . . . . . . . 85
Logging in, setting the Web configurator
language . . . . . . . . . . . . . . . . . . . . . . . 86
IP Configuration . . . . . . . . . . . . . . . . . 87
Configuring telephone connections . . 89
Optimising voice quality for VoIP
connections . . . . . . . . . . . . . . . . . . . . 97
Assigning sending and receiving numbers
to handsets . . . . . . . . . . . . . . . . . . . . 100
Setting DTMF signalling for VoIP . . . 101
Defining local communication ports for
VoIP . . . . . . . . . . . . . . . . . . . . . . . . . . 102
Setting Area Code Predialling . . . . . . 103
Loading and deleting directories to/from
the PC. . . . . . . . . . . . . . . . . . . . . . . . . 103
Defining the server for firmware updates,
starting the update . . . . . . . . . . . . . . 106
Activating/deactivating the automatic
version check . . . . . . . . . . . . . . . . . . 107
Activating VoIP status message
display . . . . . . . . . . . . . . . . . . . . . . . . 107
Checking status information via your
phone . . . . . . . . . . . . . . . . . . . . . . . . 108
Messaging . . . . . . . . . . . . . . . . . . . . . 109
Using the Web configurators . . . 64
Configuring the base station router and
phone via a PC . . . . . . . . . . . . . . . . . . 64
Starting the Web configurator . . . . . . 65
Logging off . . . . . . . . . . . . . . . . . . . . . 65
Structure of the Web pages . . . . . . . . 66
Opening Web pages . . . . . . . . . . . . . . 68
Version 2, 21.12.2006
Router Web configurator . . . . . . 69
Connecting the PC to the router Web
configurator . . . . . . . . . . . . . . . . . . . . 69
Login . . . . . . . . . . . . . . . . . . . . . . . . . . 69
Internet – configuring the connection to
the Internet. . . . . . . . . . . . . . . . . . . . . 71
Connection – entering access data for the
Internet connection . . . . . . . . . . . . . . 71
Setting up the Firewall . . . . . . . . . . . . 74
Setting up NAT . . . . . . . . . . . . . . . . . . 75
DNS – entering the DNS server . . . . . 78
QoS – setting the Quality of Service,
prioritising VoIP . . . . . . . . . . . . . . . . . 78
Setting Routing . . . . . . . . . . . . . . . . . . 79
Configuring the local network . . . . . . 80
Defining the router's name
and domain . . . . . . . . . . . . . . . . . . . . 81
Setting the Regional Options . . . . . . . 81
Setting or changing a password . . . . . 82
Setting the time until
automatic log-off . . . . . . . . . . . . . . . . 82
Configuring Remote Management for the
router from external networks . . . . . . 82
Updating the router's firmware . . . . . 83
Displaying the security log . . . . . . . . . 83
Reboot . . . . . . . . . . . . . . . . . . . . . . . . 83
Checking status information
via the router . . . . . . . . . . . . . . . . . . . 84
Appendix . . . . . . . . . . . . . . . . . 112
Symbols and typographical conventions
used . . . . . . . . . . . . . . . . . . . . . . . . . . 112
Care . . . . . . . . . . . . . . . . . . . . . . . . . . 112
Contact with liquid . . . . . . . . . . . . . . 112
Questions and answers . . . . . . . . . . . 113
Searching for service information . . 119
Service (Customer Care) . . . . . . . . . . 120
Authorisation . . . . . . . . . . . . . . . . . . 121
Specifications . . . . . . . . . . . . . . . . . . 121
Writing and editing a text message . 124
Gigaset CE 460 IP R – Free software . 127
Accessories . . . . . . . . . . . . . . . . 134
Glossary . . . . . . . . . . . . . . . . . . 135
Index . . . . . . . . . . . . . . . . . . . . . 147
3
CE 450 IP R / IM-Ost english / A31008-M1817-R601_1-7619 / security.fm / 02.03.2007
Safety precautions
Warning:
Read the safety precautions and the user guide before use.
Explain their contents and the potential hazards associated with using the telephone to your children.
$
Only use the mains adapter supplied, as indicated on the underside of the base station.
Use only recommended rechargeable batteries (page 121) of the same type! Never use
a conventional (non-rechargeable) battery or other battery types as this could result in significant health risks and personal injury.
‹
Œ
Insert rechargeable batteries with the correct polarity, and use them according to this user
guide (polarity symbols can be seen in the handset's battery compartment, page 8).
The operation of medical appliances may be affected. Be aware of the technical conditions
in your particular environment, e.g. doctor's surgery.
Do not hold the rear of the handset to your ear when it is ringing or when the handsfree
function is activated. Otherwise you risk serious and permanent damage to your hearing.
The handset may cause an unpleasant humming noise in hearing aids.
Do not install the base station in bathrooms or shower rooms. The handset and base station are not splashproof (page 112).
Do not use your phone in environments with a potential explosion hazard, e.g. paint
shops.
ƒ
If you give your Gigaset to someone else, make sure you also give them the user guide.
All electrical and electronic equipment must be disposed of separately from general
household waste using the sites designated by local authorities.
If a product displays this symbol of a crossed-out rubbish bin, the product is subject to
European Directive 2002/96/EC.
The appropriate disposal and separate collection of used equipment serve to prevent
potential harm to the environment and to health. They are a precondition for the re-use
and recycling of used electrical and electronic equipment.
For further information on disposing of your used equipment, please contact your local
authority, your refuse collection service or the dealer you purchased the product from.
Please note:
Version 2, 21.12.2006
When the keypad lock is active you cannot even call emergency numbers!
Not all of the functions described in this manual are available in all countries.
4
CE 450 IP R / IM-Ost english / A31008-M1817-R601_1-7619 / starting.fm / 02.03.2007
Gigaset CE 460 IP R – more than just a telephone
Gigaset CE 460 IP R – more than just a telephone
Your Gigaset CE 460 IP R is not only a router and phone in one device that you can use to
make cost-effective calls via the Internet (VoIP - Voice over IP) and with which you can connect other participants in your local network (e.g. PCs) to the Internet via the same Internet
account;
your Gigaset CE 460 IP R can do much more:
u Multiline: Register up to six handsets to your base station and set up an individual VoIP
account with its own phone number for each member of your family (up to six accounts
with different VoIP providers). Your phone can then be reached via up to six different
phone numbers, which you can assign to the individual handsets. If a member of your
family is called on their number, only their handset will ring.
u Use Gigaset.net for VoIP calls. Connect your base station to the mains power supply and
Internet and make calls – without making any further VoIP settings – to other
Gigaset.net subscribers free of charge (page 34).
u Use the base station router wizard. When you are putting your base station into service,
the wizard guides you step-by-step through the configuration of your Internet connection (page 15).
u Configure the VoIP connection directly on your handset. The connection assistant
downloads general data about a VoIP provider from the Internet and guides you through
entering your personal data (first account). This makes it easy for you to start using VoIP
(page 18).
u Make further settings on your PC, if necessary. The phone has two Web interfaces
(router and phone Web configurator), which you can access via the Web browser on
your PC (page 85).
u Use your base station's firewall and NAT (Network Address Translation). This will allow
you to protect your local network from unauthorised access from the Internet.
u Assign individual passwords (a system PIN and router password) to protect your base
station's phones and routers against unauthorised access (page 56, page 82).
u Save up to 100 phone numbers on your handset (page 40).
u Transfer your Outlook contacts from the PC onto your handset. Or back up the handset
directory on your PC (page 103).
u You can programme the keys of your handset with important phone numbers. The
phone number is then dialled by simply pressing the respective key (page 41).
u Keep your hands free when making a call. Use the handsfree function on your handset
(page 30) or use the convenient headset to make calls (page 22, accessories: not
included in the scope of delivery).
u Keep your base station up to date. Find out about firmware updates on the Internet
and download these to your base station (page 58, page 106).
u Use your handset as an alarm clock (page 55).
Version 2, 21.12.2006
Your Gigaset CE 460 IP R has a protected operating system that offers increased security against
viruses from the Internet.
Enjoy using your new telephone!
5
CE 450 IP R / IM-Ost english / A31008-M1817-R601_1-7619 / starting.fm / 02.03.2007
VoIP – making calls via the Internet
VoIP – making calls via the Internet
With VoIP (Voice over Internet Protocol), your calls are not made via a fixed connection as
in the telephone network, but rather they are transmitted via the Internet in the form of
data packets.
You can take advantage of all the benefits of VoIP with your Gigaset CE 460 IP R:
u You can make cost-effective calls at high voice quality with subscribers on the Internet,
the fixed network or the mobile phone network.
u VoIP providers will give you personal numbers, with which you can be reached from the
Internet, the fixed network and any mobile phone network.
To be able to use VoIP, you need the following:
u A broadband Internet connection (e.g. DSL) with flat rate (recommended) or volumebased price.
u Internet access, i.e. a DSL modem, which you can use to connect your base station's
router to the Internet, and an Internet account.
u Access to the services of a VoIP provider. Open up to six accounts with different VoIP
providers.
Base station components
The Gigaset CE 460 IP R base station includes two independent components: the base
station router and base station phone, also frequently described as the router and phone
in the text that follows. These components must be configured and managed separately
from one another.
Base station router
u You can make router settings for the Internet connection and local network, and man-
age your router on your PC using the router Web configurator (see page 69).
u You can protect the router and its settings via an individual password. This password will
not allow access to the base station phone settings.
u The router is supplied with the following standard settings:
Version 2, 21.12.2006
–
–
–
–
6
Private IP address: 192.168.1.1
IP address block: 192.168.1.2 to 192.168.1.253
DHCP server enabled with IP address block: 192.168.1.100 to 192.168.1.150
Password: 0000 (4x zero)
CE 450 IP R / IM-Ost english / A31008-M1817-R601_1-7619 / starting.fm / 02.03.2007
VoIP – making calls via the Internet
Base station phone
u You can make phone or VoIP telephony settings with the handset or on your PC via the
phone Web configurator (see page 85).
u The phone settings are protected with a system PIN.
u The phone is supplied with the following standard settings for connection to the router.
–
–
–
–
DHCP client: enabled
IP address: 192.168.1.150
Standard gateway and DNS server: 192.168.1.1
System PIN: 0000
An existing connection is set between the router and phone by default.
System requirements for the PC you want to use to configure your base station
u Ethernet socket
u Web browser, such as Microsoft Internet Explorer version 6.0 or higher, or Mozilla
Version 2, 21.12.2006
Firefox version 1.0.4 or higher
7
CE 450 IP R / IM-Ost english / A31008-M1817-R601_1-7619 / starting.fm / 02.03.2007
First steps
Pack contents
First steps
Pack contents
The pack contains:
u one Gigaset CE 460 IP R base station
u one Gigaset C46 handset
u one mains adapter for the base station
u one charging cradle incl. mains adapter
u one Ethernet cable Cat 5 with RJ45 modular jacks
u two batteries
u one battery cover
u one belt clip
u one quick guide
Firmware updates:
Whenever there are new or improved functions for your Gigaset CE 460 IP R, phone and/or router
firmware updates will be made available for you to download to your base station (page 58, page 83).
If this results in operational changes to your phone, a new version of the existing user guide will be
published on the Internet at www.siemens.com/gigaset
Setting up the handset for use
The display is protected by a plastic film. Please remove the protective film!
Inserting the batteries
Warning:
Version 2, 21.12.2006
Only use the rechargeable batteries recommended by Siemens Home and Office Communication
Devices GmbH & Co. KG on page 121. Never use a conventional (non-rechargeable) battery or other
battery types as this could result in significant health risks and personal injury.For example, the batteries could explode. The phone could also malfunction or be damaged as a result of using batteries
that are not of the recommended type.
8
CE 450 IP R / IM-Ost english / A31008-M1817-R601_1-7619 / starting.fm / 02.03.2007
Setting up the handset for use
First steps
¤ Insert the batteries the right way round (see figure).
The polarity is indicated in the battery compartment.
Closing the battery cover
¤ First align the notches on the side of the battery cover with the lugs on the inside of the
casing.
¤ Then press the cover so that it clicks into place.
Attaching the belt clip
Version 2, 21.12.2006
There are notches for attaching the belt clip on the side of the handset at the same height
as the display.
¤ Press the belt clip onto the back of the handset so that the protrusions on the belt clip
engage with the notches.
9
CE 450 IP R / IM-Ost english / A31008-M1817-R601_1-7619 / starting.fm / 02.03.2007
First steps
Setting up the handset for use
Opening the battery cover
¤ If fitted, remove belt clip.
¤ Insert a fingernail into the notch and pull the battery cover upwards.
Connecting the charging cradle
Connecting the charging cradle and mounting it on the wall (if required) is described at the
end of this user guide.
¤ To charge the batteries, leave the handset in the charging cradle.
Please note:
– Only place the handset in the charging cradle that is intended for it.
– If the handset has switched itself off because the batteries are flat and if it is then placed in the
charging cradle, it will switch itself on automatically.
For questions and problems see page 113.
Initial charging and discharging of batteries
Battery charging is indicated in the top right of the display by a flashing battery icon e,
V or U. During handset operation, the battery icon indicates the charge status of the
batteries (page 1).
The correct charge status can only be displayed when the batteries are first fully charged
and discharged through use.
¤ To do this, leave the handset in the charging cradle without interruption until the battery icon stops flashing in the display (around 13 hours).
¤ Once the batteries are fully charged, remove the handset from the charging cradle and
do not put it back again until the batteries are fully discharged.
Please note:
Version 2, 21.12.2006
After the first battery charge and discharge, you may place your handset in the charging cradle after
every call.
Please note:
u Always repeat the charging and discharging procedure if you remove the batteries from
the handset and reinsert them.
10
CE 450 IP R / IM-Ost english / A31008-M1817-R601_1-7619 / starting.fm / 02.03.2007
Installing the base station
First steps
u The batteries may warm up during charging. This is not dangerous.
u After a while the charge capacity of the batteries will decrease for technical reasons.
Please note:
You will find explanations for the symbols and typographical conventions used in this user guide in
the appendix, page 112.
Setting the date and time
§Menu§
~
¢ Settings ¢ Date/Time
Enter the day, month and year in 6-digit format and press §OK§. Use q to move
between the fields.
~
Enter hours and minutes in 4-digit format (e.g. 0 7 1 5 for 07:15) and press §OK§.
Use q to move between the fields.
The date and time are shown in the handset's idle display (page 1).
Registering the handset to the base station
The supplied handset is registered to the base station by default.
Instructions on how to register further handsets to the base station are given on page 48.
Installing the base station
The base station is designed for use in closed, dry rooms with a temperature range of
+5 °C to +45 °C.
¤ Place or hang the base station in a central position in your flat or house.
Please note:
u Never expose the telephone to heat sources, direct sunlight or other electrical
appliances.
u Protect your Gigaset from moisture, dust, corrosive liquids and vapours.
u The base station must only be operated on a LAN network (SELV network in accordance
Version 2, 21.12.2006
with IEC 60950-1) inside a building.
11
CE 450 IP R / IM-Ost english / A31008-M1817-R601_1-7619 / starting.fm / 02.03.2007
First steps
Connecting the base station
Connecting the base station
To be able to make calls via VoIP with your base station, you must connect the base station
with the Internet (WAN connection). You can connect additional devices to the base station
LAN connection; these devices can access the Internet via the base station router,
see Figure 1.
Internet
4
LAN
2
WAN
1
3
Figure 1 Base station connection
1
2
3
4
DSL modem for the Internet connection (WAN connection)
Gigaset CE 460 IP R base station
Gigaset C46 handset
Base station LAN connection, e.g.for the PC, hub, switch, router of a subnet
Follow the steps in the order given below:
1. Connect the base station WAN connection with the DSL modem
2. Connect the base station LAN connection with the Ethernet connection on your PC
3. Connect the base station with the mains power supply
Please note:
Version 2, 21.12.2006
If there are devices connected to your modem (e.g. your PC), you must first shut these
down and switch them off. Then switch the modem off and disconnect it from the mains
power supply.
12
CE 450 IP R / IM-Ost english / A31008-M1817-R601_1-7619 / starting.fm / 02.03.2007
Connecting the base station
First steps
Connecting the base station with the modem
Connect the socket labelled WAN on your base station with your DSL modem. To do this,
use the Ethernet cable supplied.
3
1
3
2
1 Side view of the base station
2 Network plug (WAN) with network cable
3 DSL modem
Connecting the PC with the base station
Before connecting a PC or laptop with the base station, please ensure:
– that a suitable network adapter is installed in/connected to your PC. Please read the operating
instructions that came with the adapter.
– that the DHCP client is enabled on your PC.
Connect the socket labelled LAN on your base station with the Ethernet connection of your
PC. To do this, use a category 5 (CAT5) Ethernet cable with RJ45 modular jacks on both
sides.
3
1
3
2
Version 2, 21.12.2006
1 Side view of the base station
2 Network plug (LAN) with network cable
3 Ethernet connection on your PC
Please note:
To get started, you must connect your base station and PC directly via the Ethernet cable!
13
CE 450 IP R / IM-Ost english / A31008-M1817-R601_1-7619 / starting.fm / 02.03.2007
First steps
Connecting the base station
Connecting the base station and modem with the mains power supply
Reconnect your modem to the mains power supply and turn it on.
Please note:
With some modems, you must wait a few minutes before turning it back on. Please consult your
modem description.
As soon as the LEDs on the modem light up, you can connect the base station with the
mains power supply.
1
2
3
1 Underside of the base station
2 Insert the 230 V mains adapter into the socket on the base station.
3 Plug the mains adapter into a power socket.
The LED on the front of the base station lights up.
Please note:
u Keep the mains adapter plugged in at all times for operation, as the base station does
not work without a mains connection.
Version 2, 21.12.2006
u Only use the mains adapter supplied with the base station.
14
CE 450 IP R / IM-Ost english / A31008-M1817-R601_1-7619 / starting.fm / 02.03.2007
Configuring the Internet connection on the base station router
First steps
Configuring the Internet connection on the base station router
Make the basic Internet access settings for the base station router via your PC.
All data required for the configuration of the Internet connection can be obtained from
your Internet service provider.
Establishing the connection to the router Web configurator
¤ Switch on your PC.
¤ If necessary, enable DHCP on your PC, i.e. activate the Obtain IP address automatically
¤
¤
option in the network settings for the LAN connection.
Start the Web browser (e.g. Internet Explorer or Firefox) on your PC.
In the Web browser's address field, enter the name or private IP address (LAN address)
of the base station router:
http://router.gigaset or
http://192.168.1.1 (default setting)
The Welcome registration page of the router opens.
¤ Enter the router password (case sensitive) and click OK. 0000 is preset as the router
password by default.
Please note:
For security reasons you should change the router password at a later stage (page 82).
When registration is finished, the router's Home page opens.
Starting the wizard for the basic router settings
The wizard for the basic router settings helps you to put your base station into service and
guides you step-by-step through the configuration process with the most important settings.
¤ Click the Basic Setup Wizard entry to start the wizard.
The Regional Options Web page is displayed.
Version 2, 21.12.2006
The wizard is operated as follows:
When you have made all the settings on a wizard Web page, click Next>. Click the <Back
button to return to the previous page. The Cancel button ends the wizard without changing the configuration of your base station.
15
CE 450 IP R / IM-Ost english / A31008-M1817-R601_1-7619 / starting.fm / 02.03.2007
First steps
Configuring the Internet connection on the base station router
Selecting the time zone for the location of the router - selecting regional options
¤ From the Country list, select the country in which your base station is being operated.
By selecting the location, you ensure that your base station can function properly in that
location.
In Time Zone, the time zone that applies to the location is displayed. It indicates the difference between the local standard time (not summer time) and the co-ordinated world
time UTC (Co-ordinated Universal Time; previously GMT = Greenwich Mean Time).
Information about the time zone is important for various time-dependent operations on
the Internet. Access control to particular services can also be defined using time-based
rules.
¤ Click the Next> button.
The Internet Connection Web page is displayed.
Setting up an Internet connection
Set up your base station's Internet connection. To do this, enter the information received
from your Internet service provider (ISP) in the fields of the Web page.
¤ First select the WAN connection type from the Connection list.
The connection type depends on what kind of Internet connection you have and on the
agreements with your Internet service provider. The access data received from your Internet service provider for registration shows you which connection type you must select.
The options are PPPoE, Static IP Address, Dynamic IP Address and PPTP.
After you have made your selection, further fields will be displayed according to your connection type; here you must enter the most important data required for an Internet connection. Further information about the individual connection types and the access data
required in each case can be found in the section "Connection – entering access data for
the Internet connection" on page 71.
For the Internet connection via PPPoE, your router is set so that it is permanently connected with the
Internet. This means that you can always be reached for VoIP calls.
Defining the maximum bandwidth for data uploads
Version 2, 21.12.2006
The Upstream Rate field is displayed on the Internet Connection Web page, irrespective of the
Connection chosen. These parameters affect the voice quality of your VoIP calls.
In the Upstream Rate field, enter the maximum amount of your Internet connection's bandwidth that should be available for data uploads. First enter the upload stream rate given by
your Internet service provider. Then carry out tests to check that voice quality is good during calls made at the same time as data is being uploaded and adjust the rate accordingly.
You can find detailed information about this in the full user guide (Quality of Service –
QoS). This is available on the Internet at: www.siemens.com/gigaset.
More entries and settings for the Internet connection can be made at a later stage via the
Router Settings menu of the router Web configurator (page 71).
16
CE 450 IP R / IM-Ost english / A31008-M1817-R601_1-7619 / starting.fm / 02.03.2007
Making settings for VoIP telephony on the base station phone
First steps
Completing the router configuration
¤ After entering your access data, click Next>.
The Apply Settings Web page is displayed.
¤ Click Finish. The start screen will be displayed again.
The Internet Status is displayed on the right-hand side of the start screen. If your settings
were successful, the status is Connected. Please note that it can take some time for the
router to establish the Internet connection.
¤ Click Log Off (top right-hand side of the Web page) to log off from the router Web
configurator.
You are now able to establish VoIP connections within Gigaset.net (page 34).
Test the Internet connection by surfing, i.e. entering a public URL in the Web browser address field
(http://www....).
Making settings for VoIP telephony on the base station phone
Before you can use the Internet (VoIP) to phone any other subscribers on the Internet, the
fixed network or the mobile phone network, you need the services of a VoIP provider.
Precondition: You have registered (e.g. via your PC) with a VoIP provider and set up an
account. The provider must support the VoIP SIP standard.
The following phone settings are necessary in order for you to use VoIP. You will receive all
information from your VoIP provider:
u Your user name with the VoIP provider, if this is required by the VoIP provider
u Your registration name
u Your password with the VoIP provider
u General settings for your VoIP provider (server addresses etc.)
The connection assistant will help you with the settings.
Before making the settings below, test the VoIP connection of your base station with the echo service
from Gigaset.net:
Dial 1234#9 on your handset and press the talk key c.
If the connection has been correctly established, you will hear your echo.
If problems with your phone connection arise after you have made the VoIP settings below, check
whether you have correctly entered your access data or contact your VoIP provider.
¥
Please note:
Version 2, 21.12.2006
Here is a description of how to make settings on your handset.
You can also make settings via your phone's Web configurator. You can start this, e.g. directly from
the start screen of the router Web configurator. To do this, click Telephony Settings. You will find the
description of the phone Web configurator from page 85 onwards.
17
CE 450 IP R / IM-Ost english / A31008-M1817-R601_1-7619 / starting.fm / 02.03.2007
First steps
Making settings for VoIP telephony on the base station phone
Starting the connection assistant
Prerequisite: The base station is connected with the mains power supply and the Internet.
Please note:
For your base station, i.e. for the phone and router, dynamic assignment of the IP address is preset
(DHCP enabled).
If you have disabled DHCP on the router, you must first assign your phone a fixed IP address and save
the router's private IP address (192.168.1.1 by default) as the standard gateway and DNS server on
your phone, see page 59.
If the handset battery is sufficiently charged, the message key f on the handset will flash
(around 20 minutes after you have put the handset in the charging cradle).
¤ Press the message key f.
You will see the following display:
Start VoIP
Connection
Assistant?
§§§§No§§§§
§§§§§Yes§§§§
Press the display key to start the connection assistant.
~
Enter the system PIN of the base station (the default is 0000) and press §OK§.
If you press §No§, the procedure that follows is described under "Entering names in the
Gigaset.net directory" on page 20.
§Yes§
Please note:
The connection assistant will also start automatically if you try to establish a connection via the Internet, before you have made the necessary settings.
You can also call up the connection assistant at any time via the menu (page 61).
Downloading data from the first VoIP provider
You will see the following display:
Select
VoIP-Provider?
§§§§No§§§§
§Yes§
§§§§§Yes§§§§
Press the display key.
Version 2, 21.12.2006
The phone establishes an Internet connection to the Siemens server, where various profiles with general access data are available for different VoIP providers. If the phone cannot establish the connection, Server not accessible! will be displayed. See page 21 for details on how you can test/establish the
Internet connection if necessary.
The message Select country appears in the display.
After changing the display:
q
Select country and press §OK§.
Select provider is displayed.
18
CE 450 IP R / IM-Ost english / A31008-M1817-R601_1-7619 / starting.fm / 02.03.2007
Making settings for VoIP telephony on the base station phone
First steps
After changing the display:
q
Select your VoIP provider and press §OK§.
The necessary data for your VoIP provider is downloaded and saved on the phone.
Please note:
If the data for your VoIP provider is not offered for download, you must make the necessary settings
with the Web configurator at a later stage (page 90).
Press the display key §Back§ twice. You can then conduct the following steps with the connection
assistant (see "Entering user data for your first VoIP account").
Entering user data for your first VoIP account
Enter the VoIP user data for the first VoIP account. This data can be obtained from your VoIP
provider.
You can enter five additional VoIP accounts (VoIP phone numbers) via the Web configurator at a later
stage (page 90). Your phone can then be reached via up to six different phone numbers. You can
assign the phone numbers to the individual handsets that are registered with the base station as
sending and receiving numbers (page 100).
Username:
Is only displayed when your provider requires a user name.
Enter name and press §OK§.
Authentication Name:
Enter name and press §OK§.
Authentication Password:
Enter password and press §OK§.
Please note:
When making these entries, please remember the VoIP user data is case sensitive. If necessary, press
and hold the # key to switch between upper and lower case and digits.
If you have made all the necessary entries, the Gigaset.net assistant is started. You have
the option of entering yourself in the Gigaset.net online directory with your own choice
of name.
Version 2, 21.12.2006
This step is only carried out when the device is first put into service (when the connection assistant
is started up for the first time). You can create the entry via the Gigaset.net directory (page 34).
19
CE 450 IP R / IM-Ost english / A31008-M1817-R601_1-7619 / starting.fm / 02.03.2007
First steps
Making settings for VoIP telephony on the base station phone
Entering names in the Gigaset.net directory
With Gigaset.net you can call other Gigaset.net users directly over the Internet free of
charge, without setting up an account with a VoIP provider and without making any further
settings. You can find Gigaset.net subscribers by carrying out a name search in the
Gigaset.net (page 34) directory.
The following appears in the handset's display:
Start
Gigaset.net
assistant?
§§§§No§§§§
§§§§§Yes§§§§
Press the display key if you want to enter yourself in the Gigaset.net directory.
If you press §No§, the procedure that follows is described under "Completing the
settings".
Own Gigaset.net name:
Enter the name that you would like to be listed under in the Gigaset directory
and press §OK§. The name may contain up to 25 characters.
A connection to the Gigaset.net server is established.
If there is already an entry under this name, you receive a message to this effect and you
will be asked to enter a name again.
If an entry in the Gigaset.net directory is successful, the message "Name added to
Gigaset.net!" is displayed briefly.
§Yes§
If the attempt to create the entry fails (e.g. because the phone is not connected to the Internet), a
message to this effect is displayed briefly, see page 21. You can then create the entry later via the
Gigaset.net directory (page 34).
Completing the settings
The handset returns to idle status.
If all the settings for your first VoIP account are correct and if the phone can establish a connection to the VoIP server, then the internal name of the handset will be displayed:
¨
V
L
INT 1
11.02.07
11:56
§§§§INT§§§§
§§§§§Menu§§§§
You can now make calls with your phone via the Internet!
Please note:
Version 2, 21.12.2006
To ensure that you can always be reached via the Internet, your base station router has been set so
that it is continuously connected to the Internet.
20
CE 450 IP R / IM-Ost english / A31008-M1817-R601_1-7619 / starting.fm / 02.03.2007
Making settings for VoIP telephony on the base station phone
First steps
No connection to the Internet/VoIP server
If one of the following messages is displayed instead of the internal name after the connection assistant is closed, then either a fault has occurred or your information was incomplete:
Server not accessible!
The phone has no connection to the Internet.
¤ Check the cable connection between the base station and the modem/Internet connection.
¤ Check your router's Internet status:
¤ Start the router Web configurator (page 69).
The Internet Status is displayed on the start screen. If necessary, check the access data
stored in the router (page 71).
¤ Check whether the IP address settings for the base station phone and base station router
are compatible.
Please note the following:
– The IP address for the phone must belong to the address block for the router. For
example:the first three parts of the IP addresses for the phone and the router in subnet mask 255.255.255.0 must be identical.
– The IP address for the phone must not be assigned to any other LAN subscriber. If the
DHCP server for the router is enabled, then no static IP address can belong to the
address block that is reserved for dynamically assigning IP addresses (default setting:
192.168.1.100 – 192.168.1.150)
– If the phone is to be dynamically assigned an IP address, then the router's DHCP
server has to be activated.
¤ Find the phone's IP address via the handset menu:
§Menu§ ¢ Settings ¢ Base ¢ Local Network ¢ (enter system PIN) ¢ IP Address
¤ Start the phone Web configurator with the IP address (page 65).
If no connection can be established:
¤ change the settings on the router (activate DHCP server, change DHCP settings, see
page 80) or
¤ activate dynamic assignment of address to the phone (page 60) or
¤ change the phone's (fixed) IP address (page 60).
Recommendation:
Version 2, 21.12.2006
You should restart your base station and the connected devices (PC) as soon as you make changes in
your LAN to IP addresses or address blocks. During the restart you should start the base station first
(page 83) and then the connected devices (PC). This will deactivate old IP addresses and force new
dynamic IP addresses to be assigned/requested.
21
CE 450 IP R / IM-Ost english / A31008-M1817-R601_1-7619 / starting.fm / 02.03.2007
First steps
Belt clip and headset
SIP registration failed!
u Your personal data for registering with the VoIP provider may have been entered incompletely or incorrectly.
¤ Check your entries for Username, Authentication Name and Authentication Password. In
particular, check your use of upper and lower case.
To do this, open the following menu on your handset:
§Menu§ ¢ Settings ¢ Base ¢ Telephony ¢ VoIP
u The server address for the VoIP server has not yet been entered, or has been entered
incorrectly.
¤ Start the phone Web configurator.
¤ Open the following Web page: Settings ¢ Telephony ¢ Connections.
¤ Edit the server address where necessary.
Please note:
– STUN (Simple Transversal of UDP over NAT) should always be deactivated on your base station
phone (default setting), and a port number from the block 5056 – 5071 should be set for the local
SIP port (default 5060).
Check these settings if you cannot hear the other caller or if you cannot be reached.
You can set STUN mode (page 94) and the local SIP port (page 102) via the phone Web
configurator.
– If port forwarding is activated on your router for the ports that have been registered as the SIP port
(default 5060) and the RTP port (default 5004), it makes sense to assign the phone a static IP
address (otherwise you may not be able to hear the other party during VoIP calls), see page 59.
Please note that the IP address and subnet mask depend on the router's address block.
You must also enter the standard gateway and DNS server. The IP address for the router is
generally entered here.
You will find other messages and possible measures in the "Questions and answers" section
on page 113.
Belt clip and headset
By using a belt clip and headset (optional) you can easily make your handset a constant
companion.
Attaching the belt clip
There are notches for attaching the belt clip on the side of the handset at approximately
the same height as the display.
¤ Press the belt clip onto the back of the handset so that the protrusions on the belt clip
engage with the notches.
The tongue of the belt clip must face the battery compartment.
Version 2, 21.12.2006
Connection socket for headset
You can use headsets with jack connectors. The following models have been tested and are
therefore recommended: HAMA Plantronics M40, MX100 and MX150.
The transmission quality of other models cannot be guaranteed.
22
CE 450 IP R / IM-Ost english / A31008-M1817-R601_1-7619 / menuetree.fm / 02.03.2007
Phone menu
Menu trees
Phone menu
There are two ways to select a function:
Using number combinations ("shortcut")
¤ To open the main menu, press §Menu§ with the handset in idle status.
¤ Enter the number combination that is in front of the function in the menu tree.
¤ Example: §Menu§ 4 2 2 for "Set handset language".
Scrolling through the menus
¤ To open the main menu, press §Menu§ with the handset in idle status.
¤ Scroll to the function with the control key s and press §OK§.
2
page 55
Alarm Clock
2-1 Activation
2-2 Wake up time
3
Audio Settings
3-1 Ringer Volume
3-2 Ringer Melody
page 54
3-2-1 External Calls
page 54
3-2-2 Internal Calls
3-2-3 Alarm Clock
3-3 Advisory Tones
3-4 Battery Low
page 55
3-4-1 Off
page 55
3-4-2 On
Version 2, 21.12.2006
3-4-3 During Call
23
CE 450 IP R / IM-Ost english / A31008-M1817-R601_1-7619 / menuetree.fm / 02.03.2007
Phone menu
4
Settings
4-1 Date/Time
4-2 Handset
page 11
4-2-1 Display
4-2-1-1 Screensaver
page 52
4-2-1-2 Colour Scheme
4-2-1-3 Contrast
4-2-1-4 Backlight
4-3 Base
4-2-2 Language
page 52
4-2-3 Auto Answer
page 53
4-2-4 Register Handset
page 48
4-2-5 Reset Handset
page 56
4-3-1 Calls List Type
4-3-1-1 Missed Calls
page 45
4-3-1-2 All Calls
4-3-2 Music on hold
page 57
4-3-3 System PIN
page 56
4-3-4 Base Reset
page 57
4-3-5 Additional Features
4-3-5-1 Repeater Mode
page 58
4-3-6 Local Network
4-3-6-1 dynamic
IP address
page 60
4-3-6-2 IP Address
page 60
4-3-6-3 Subnet Mask
page 60
4-3-6-4 DNS Server
page 61
4-3-6-5 Default Gateway page 61
4-3-7 Telephony
5
Version 2, 21.12.2006
page 58
5-1-1 Network Mailbox
page 47
Select Services
6-1 VoIP
24
4-3-8 Firmware Update
Voice Mail
5-1 Set Key 1
6
submenu see page 25
6-1-6 For All Calls
6-1-6-1 Call Divert
page 38
6-1-6-3 Call Waiting
page 38
CE 450 IP R / IM-Ost english / A31008-M1817-R601_1-7619 / menuetree.fm / 02.03.2007
Phone menu
Submenu "Settings ¢ Base ¢ Telephony" 4-3-7
4-3-7 Telephony
4-3-7-2 Connection
Assistant
4-3-7-7 VoIP
page 61
4-3-7-7-1 Status on HS
page 63
4-3-7-7-2 Select VoIP
Provider
page 61
4-3-7-7-3 Username
page 62
4-3-7-7-4 Authentication page 62
Name
Version 2, 21.12.2006
4-3-7-7-5 Authentication page 62
Password
25
CE 450 IP R / IM-Ost english / A31008-M1817-R601_1-7619 / menuetree.fm / 02.03.2007
Router Web configurator menu
Router Web configurator menu
page 65
Home
Basic Setup Wizard
page 15
the basic router settings
Router Settings
Internet
Connection
page 71
Firewall
page 74
Address Translation
(NAT)
page 75
DNS
page 78
QoS
page 78
Routing
page 79
Local Network
page 80
DHCP Clients
page 81
Regional Options
page 81
Remote Management
page 82
Load Firmware
page 83
Security Log
page 83
Reboot
page 83
Administration
Telephony Settings
Version 2, 21.12.2006
Status
26
connection to phone Web configurator
page 85
page 84
CE 450 IP R / IM-Ost english / A31008-M1817-R601_1-7619 / menuetree.fm / 02.03.2007
Phone Web configurator menu
Phone Web configurator menu
page 65
Home
Settings
IP Configuration
page 87
Telephony
Connections
page 90
Audio
page 97
Number Assignment
page 100
Dialing Plans
page 103
Directory
page 103
Advanced Settings
page 101
Messenger
page 109
E-Mail
page 111
Messaging
Miscellaneous
page 106,
page 107
Device
page 108
connection to router Web configurator
page 69
Status
Version 2, 21.12.2006
Router-Settings
27
CE 450 IP R / IM-Ost english / A31008-M1817-R601_1-7619 / telephony.fm / 02.03.2007
Making an external call
Making calls
Making an external call
External calls are calls made via the Internet (VoIP).
¤ Enter the required number/IP address using the keypad.
¤ Press the talk key c.
Please note:
– You can specify for each handset registered to your base station which of your VoIP phone numbers (which VoIP account) should be used for outgoing external VoIP calls (page 100).
– If you use VoIP to make a call to the fixed network, you may also have to dial the area code for local
calls (depending on the VoIP provider). You can also enter the area code in the base station configuration so you do not always need to enter it for local calls (via the phone Web configurator,
page 103). It will then be inserted automatically for local calls.
Cancelling the dialling operation
You can cancel the dialling operation with the end call key a.
Entering an IP address
You can also enter an IP address instead of a phone number.
¤ Press the star key P to separate the sections of the IP address (e.g. 149*246*122*28).
¤ If necessary, press the # key to attach the SIP port number of the person you are calling (page 144) to the IP address (e.g. 149*246*122*28#5060).
Please note:
– Dialling with the directory (page 40) or last number redial list (page 43) saves repeated keying of
phone numbers.
– You can assign a number from the directory to a key for speed dialling (page 41).
– You can edit or add to any phone number selected by means of speed dial or from the directory
and use it for the current call.
Ending a call
Version 2, 21.12.2006
a
28
Press the end call key.
CE 450 IP R / IM-Ost english / A31008-M1817-R601_1-7619 / telephony.fm / 02.03.2007
Accepting a call
Accepting a call
The handset indicates an incoming call in three ways: by ringing, by a display on the screen
and by the flashing handsfree key d.
Please note:
The handset will indicate the following calls:
– Calls to receiving numbers that are assigned to this handset (page 100).
– Calls to receiving numbers that are not allocated as receiving numbers to any handsets.
You can accept the call by:
¤ Pressing the talk key c.
¤ Pressing the handsfree key d.
If the handset is in the charging cradle and the Auto Answer function is activated (page 53),
the handset will take a call automatically when you lift it out of the cradle.
If the ringer tone is intrusive, press §Menu§ ¢ Silent. You can accept the call so long as it is
displayed on the screen.
Call display
When you receive an incoming call, the caller's number and/or the name they have specified is displayed on the screen.
If the caller's number is stored in your directory, the name from the directory will be displayed instead.
W
1234567890
For IP1
Menu§
1
2
3
Version 2, 21.12.2006
1 Ringer icon (VoIP)
2 Number or name of caller (abbreviated if necessary).
If no number is transmitted, External Call will be displayed.
3 Receiving number: indicates which of your VoIP phone numbers the caller has dialled. You assign
the names when you enter the VoIP phone numbers into the phone (page 89). For calls from
Gigaset.net, For Gigaset.net is displayed.
29
CE 450 IP R / IM-Ost english / A31008-M1817-R601_1-7619 / telephony.fm / 02.03.2007
Handsfree talking
Handsfree talking
In handsfree mode, instead of holding the handset to your ear you can stand it up or lay it
down, e.g. on the table in front of you, to allow others to participate in the call.
Activating/deactivating handsfree mode
Activating while dialling
~d
Enter the number and press the handsfree key.
¤ You should inform your caller before you use the handsfree function so that they know
someone else is listening.
Switching between earpiece and handsfree mode
d
Press the handsfree key.
Switch handsfree on and off during a call.
If you wish to place the handset in the charging cradle during a call:
¤ Press and hold the handsfree key d while placing the handset in the charging cradle. If
the handsfree key d does not light up, press the key again.
For how to adjust the loudspeaker volume, see page 53.
Muting the handset
You can deactivate the microphone in your handset during an external call. The other party
hears hold music.
Muting the handset
§INT§
Press the display key.
Cancelling muting
Version 2, 21.12.2006
§Back§
30
Press the display key.
CE 450 IP R / IM-Ost english / A31008-M1817-R601_1-7619 / telephony.fm / 02.03.2007
Activating/deactivating the handset
Operating the handset
Activating/deactivating the handset
a
Press and hold the end call key.
You will hear the confirmation tone.
Activating/deactivating the keypad lock
#
Press and hold the hash key.
You will hear the confirmation tone. The Ø icon appears in the display when the keypad
lock is activated.
The keypad lock deactivates automatically when you receive a call and activates again after
the call.
Please note:
If the keypad lock is activated and you accidentally press a key, an advisory message will be displayed
on the screen. Press and hold the hash key # to deactivate the keypad lock.
Control key
§§§§INT§§§
§§Menu
1
1 Control key
In this user guide, the side of the control key that you must press in the given operating
situation is shown in black (top, bottom). Example: t for "press up on the control key".
The control key has a number of different functions:
When the handset is in idle status
t
s
Adjust the ringer volume of the handset (page 54).
Open the directory.
In lists and menus
t/s
Scroll up/down line by line.
In an input field
Version 2, 21.12.2006
t/s
Move the cursor left or right.
31
CE 450 IP R / IM-Ost english / A31008-M1817-R601_1-7619 / telephony.fm / 02.03.2007
Display keys
During an external call
s
t
Open the directory.
Adjust the loudspeaker volume for earpiece and handsfree mode.
Display keys
The current display functions are shown in the bottom display line in reversed highlights.
The function of the display keys changes depending on the particular operating situation.
Example:
§§§§INT§§§
§§Menu
1
2
1 Current display key functions
2 Display keys
The most important display symbols are:
§Back§
Go back one menu level or cancel the operation.
§INT§
Make an internal call (page 50).
§Menu§
Open the main menu or a context-dependent menu.
§OK§
Confirm highlighted selection.
˜
Delete key: deletes one character at a time from right to left.
Reverting to idle status
Version 2, 21.12.2006
You wish to return to idle status from anywhere in the menu:
¤ Press and hold the end call key a.
Or:
¤ Do not press any key: after 2 minutes the display will automatically revert to idle status.
Changes that you have not confirmed/saved by pressing §OK§ will be rejected.
For an example of the display in idle status, see page 1.
32
CE 450 IP R / IM-Ost english / A31008-M1817-R601_1-7619 / telephony.fm / 02.03.2007
Menu guidance
Menu guidance
Your telephone's functions are accessed using a menu that has a number of levels.
Main menu (first menu level)
¤ To open the main menu, press §Menu§ with the handset in idle status.
Accessing a function
¤ Scroll to the function with the control key q and press §OK§.
Or:
¤ Enter the number that is in front of the function in the menu tree (page 23).
The corresponding submenu (the next menu level) is opened.
Submenus
The functions in the submenus are displayed as lists.
To access a function:
¤ Scroll to the function with the control key q and press §OK§.
Or:
¤ Enter the number combination that is in front of the function in the menu tree
(page 23).
A short press on the end call key a returns you to the previous menu level / cancels the
operation.
Correcting incorrect entries
u
u
u
u
Navigate to the incorrect input with the control key if û is displayed.
Press ˜ to delete the character to the left of the cursor.
Insert a new character to the left of the cursor.
When entering the time and date etc., edit the flashing character.
Version 2, 21.12.2006
You will find explanations for the symbols and typographical conventions used in this user
guide in the appendix, page 112.
33
CE 450 IP R / IM-Ost english / A31008-M1817-R601_1-7619 / netservices_SAG.fm / 02.03.2007
Searching for subscribers in the Gigaset.net directory
VoIP telephony via Gigaset.net
You can use Gigaset.net to make free phone calls via the Internet directly to other
Gigaset.net users, without having to set up an account with a VoIP provider or make any
further settings. You simply have to connect your phone to the power supply and the Internet connection and, if necessary, enter yourself in the Gigaset.net online directory under a
name of your choice (page 20/page 36).
Gigaset.net is a VoIP service from Siemens Home and Office Communication Devices
GmbH and Co KG, which all users of a VoIP phone that supports Gigaset.net can use.
You can call other subscribers to Gigaset.net free of charge, i.e. there are no telephone
charges other than the costs for your Internet connection. Connections to/from other networks are not possible.
Every Gigaset VoIP device is assigned a Gigaset.net phone number by default (page 119).
All registered subscribers are included in the Gigaset.net directory, which you are able to
access.
An echo service is available on the phone number 1234#9 for you to check your VoIP connection. After an announcement, the echo service sends back the voice data you have
received immediately in the form of an echo.
Exclusion of liability
Gigaset.net is a voluntary service provided by Siemens Home and Office Communication GmbH &
Co KG with no liability or guarantee for the availability of the network. This service can be terminated
at any time with a notice period of three months.
Please note:
If you do not use your Gigaset.net connection for six weeks, it is automatically deactivated. You
cannot be reached for calls from the Gigaset.net.
The connection is reactivated:
– as soon as you start a search in the Gigaset.net directory or
– make a call via the Gigaset.net (dial a number with #9 at the end) or
– activate the connection via the Web configurator (page 96)
Searching for subscribers in the Gigaset.net directory
Your handset is in idle status.
¤ Open the directory with the s button.
¤ Select the <Gigaset.net> entry and press the talk key c.
Please note:
Version 2, 21.12.2006
– Calls to the Gigaset.net directory are always free of charge.
– If the <Gigaset.net> entry has been accidentally deleted from your handset directory, dial 1188#9
(the Gigaset.net directory phone number) and press the talk key c, or create a new directory
entry with this number.
34
CE 450 IP R / IM-Ost english / A31008-M1817-R601_1-7619 / netservices_SAG.fm / 02.03.2007
Searching for subscribers in the Gigaset.net directory
Once the connection has been established, you will be asked to enter a name that you
want to search for.
Nickname:
Enter the name or part of a name (max. 25 characters).
§Menu§
Press the display key.
Start search
Select and press §OK§.
If the search has been successful, a hit list will be displayed of all the names that begin with
the specified character string.
Example:
2/50
Sand, Anna Magd
alena
§View§
U
1
2
§Menu
1. 2/50: Entry number/number of hits
2. Name of the entry, the name is displayed in full, if necessary over several lines
You can scroll through the hit list with q.
If it has not been possible to find a matching entry, a corresponding message is displayed.
You have the following options:
¤ Press the display key §New§ to start a new search.
Or
¤ Press the display key §Change§ to change the search criteria. The previously entered name
is copied and can be edited.
If there are too many matching entries in the Gigaset.net directory, the message Too many
entries found! is displayed instead of a hit list.
¤ Press the display key §Refine§ to start a refined search. The previously entered name is
copied and can be edited/expanded.
Calling subscribers
q
c
Select the subscriber from the hit list.
Press the talk key.
Viewing the subscriber's number
q
Select the subscriber from the hit list.
Press the display key.
The Gigaset.net number and name will be shown in full, if necessary using more than one
line.
§View§
Please note:
Version 2, 21.12.2006
You can open the Gigaset.net directory and establish connections, even if you have not entered
yourself in the Gigaset.net directory.
35
CE 450 IP R / IM-Ost english / A31008-M1817-R601_1-7619 / netservices_SAG.fm / 02.03.2007
Searching for subscribers in the Gigaset.net directory
Using other functions
Precondition: The hit list is displayed.
q (Select entry) ¢ §Menu§
The following functions can be selected with q:
Copy to Directory
Copy the number to the handset directory. The number and name (where appropriate
abbreviated, max. 16 characters) are copied to the directory.
¤ Edit and save entry where appropriate (page 40).
The hit list is displayed again.
New search
Start a search with a new name (page 35).
Refine search
You can use the refined search to limit the number of hits for a previous search. The
name from the previous search is copied and can be edited/expanded.
Own information
See "Viewing, editing and deleting own entry" on page 36
Please note:
If you select a Gigaset.net number from the handset directory, the connection is automatically established via the Internet.
Viewing, editing and deleting own entry
You have the following options:
u Edit the name of your entry in the Gigaset.net directory.
u Delete your entry from the directory.
u If you did not enter a name when using the phone for the first time (page 20), specify
a name and enter yourself in the directory.
Viewing own entry
You are connected to the Gigaset.net directory:
¤ Select §Menu§ ¢ Own information and press §OK§.
Version 2, 21.12.2006
Your Gigaset.net number and, where applicable, your currently entered name are
displayed.
36
CE 450 IP R / IM-Ost english / A31008-M1817-R601_1-7619 / netservices_SAG.fm / 02.03.2007
Calling a Gigaset.net subscriber
Entering/editing a name
Press the display key.
Edit name or enter new name (max. 25 characters) and press §OK§.
You can delete the name with ˜.
If there is not yet an entry with this name in the Gigaset.net directory, the name is saved.
A message to this effect is displayed. The handset switches to idle status.
§Change§
~
If there is already an entry with this name, or the entered name contains impermissible
characters, you will be requested to enter a different name.
Please note:
If you delete the name, your entry will be deleted from the directory. You are no longer "visible" to
other Gigaset.net subscribers. However, you can still be reached via your Gigaset.net number. For
information on how to display the number, see page 119.
Calling a Gigaset.net subscriber
Version 2, 21.12.2006
You can call a Gigaset.net subscriber directly via the Gigaset.net directory (see above) or
via their Gigaset.net number:
~ /s
Enter the Gigaset.net number (including the #9) or select from the handset
directory.
c
Press the talk key.
Every number ending with #9 is dialled via Gigaset.net.
37
CE 450 IP R / IM-Ost english / A31008-M1817-R601_1-7619 / netservices_SAG.fm / 02.03.2007
Settings for all calls
Network services - VoIP
Settings for all calls
Call forwarding takes place locally in your base station.
Please note that call forwarding may incur additional costs. Ask your VoIP provider.
Setting up call forwarding
§Menu§
¢ Select Services ¢ VoIP ¢ For All Calls ¢ Call Divert
A list of your phone's configured and activated VoIP phone numbers will be displayed. VoIP
phone numbers for which call forwarding is activated are identified with ‰.
Setting up call forwarding, changing the setting
q
Select the VoIP phone number for which you want to activate or change call forwarding and press §OK§.
All Calls / No Answer / When Busy
Select and press §OK§ (‰ = on).
On
Select and press §OK§.
~
If necessary, enter the number to which the call is to be forwarded. You can
enter a fixed network, VoIP or mobile number.
§OK§
Press the display key.
a
Press and hold (idle status).
Call forwarding is activated for the selected VoIP phone number (receiving number).
Deactivating call forwarding
q
Select the VoIP phone number for which you want to deactivate call forwarding
and press §OK§.
§OK§
Press the display key.
Off
Select and press §OK§.
a
Press and hold (idle status).
Call forwarding is deactivated.
Version 2, 21.12.2006
Activating/deactivating call waiting
When call waiting is activated, the caller will hear the ringing tone if you are already making a call via your VoIP connection. This call is signalled acoustically and also shown on your
handset screen.
§Menu§ ¢ Select Services ¢ VoIP ¢ For All Calls ¢ Call Waiting
On/ Off
Select and press §OK§.
a
Press and hold (idle status).
38
CE 450 IP R / IM-Ost english / A31008-M1817-R601_1-7619 / netservices_SAG.fm / 02.03.2007
Functions during a call
Functions during a call
The following functions are only available if you permit two parallel VoIP connections for
your telephone (see page 97, Allow 1 VoIP call only).
Consultation
During a VoIP call:
§Menu§ ¢ External Call
~
Enter the number or copy from the directory.
c
Press the talk key.
The number will be dialled via the handset's VoIP sending number.
Please note:
– If the second VoIP connection is busy or there is no second VoIP connection available, you will hear
a busy tone and return to the first participant.
– After a few seconds, the number selected for a consultation call is saved in the last number redial
list.
– If the participant does not answer: press a. You are reconnected to the first participant.
If the participant answers, you have the following options:
u Toggling:
¤ Use q to toggle between the participants.
– End call with active participant: §Menu§ ¢ End Active Call.
u Conference call:
– Talk to both participants: §Menu§ ¢ Conference Call.
– End conference call (toggle): §Menu§ ¢ End Conference.
– End call with both participants: Press the end call key a.
Accepting call waiting
Precondition: Call waiting is activated (page 38). You are making an internal call or a call
via VoIP.
§Menu§ ¢ Accept Call Waiting
If the first call was an internal call, the internal connection is ended.
If the first call was an external call, you can opt to toggle or hold a conference call.
Please note:
Version 2, 21.12.2006
An internal call waiting is shown on the display. You can neither accept the internal call nor reject it.
39
CE 450 IP R / IM-Ost english / A31008-M1817-R601_1-7619 / directories_charges.fm / 02.03.2007
Directory
Using the directory and lists
The options are:
u Directory
u Last number redial list
u Calls list
You can store up to 100 entries in the directory.
You can create a personalised directory for your own individual handset. However, you can
send the list or individual entries to other handsets (page 42).
Directory
In the directory you can store numbers and corresponding names.
¤ With the handset in idle status, open the directory by pressing the s key.
Length of an entry
Number:
Name:
max. 32 digits
max. 16 characters
Please note:
– Some VoIP providers do not support local calls for calls to the fixed network. In this case, always
enter the fixed network number with the area code in your directory.
Alternatively, you can also use the Web configurator to define an area code, which is automatically
prefixed to all numbers that are dialled without an area code for calls via VoIP (see Setting Area
Code Predialling, page 103).
– You can assign a number from the directory to a key for speed dialling (page 41).
Saving the first number in the directory
s ¢ Directory empty New Entry?
~
Enter the number and press §OK§.
~
Enter the name and press §OK§.
Please note:
To find out how to enter IP addresses, turn to page 28.
Storing a number in the directory
Version 2, 21.12.2006
s ¢ §Menu§ ¢ New Entry
~
Enter the number and press §OK§.
~
Enter the name and press §OK§.
40
CE 450 IP R / IM-Ost english / A31008-M1817-R601_1-7619 / directories_charges.fm / 02.03.2007
Directory
Selecting a directory entry
s
Open the directory.
You have the following options:
u Use q to scroll to the entry until the required name is selected.
u Enter the first character of the name, or scroll to the entry with q.
Dialling with the directory
s ¢ q (select entry; page 41)
c
Press the talk key.
Please note:
You can only dial IP addresses via VoIP.
Managing directory entries
You have selected an entry (page 41).
Editing entries
§Menu§
~
~
¢ Edit Entry
Edit the number if required, and press §OK§.
Edit the name if required, and press §OK§.
Assigning a key
You can assign keys Q and 2 to O with a number. The number is then dialled by simply
pressing a key.
§Menu§ ¢ Shortcut
Assign the current entry for speed dial to a selected key.
Using other functions
Version 2, 21.12.2006
s ¢ s (select entry; page 41) ¢ §Menu§
The following functions can be selected with q:
Use Number
Edit or add to a saved number. Then dial or use other functions with §Menu§.
Delete Entry
Delete selected entry.
Send Entry
Send a single entry to another handset (page 42).
Delete List
Delete all directory entries.
Send List
Send the complete list to another handset (page 42).
Using speed dial keys
¤ Press and hold the required speed dial key.
41
CE 450 IP R / IM-Ost english / A31008-M1817-R601_1-7619 / directories_charges.fm / 02.03.2007
Directory
Sending the directory to another handset
Preconditions:
u The sending and receiving handsets must both be registered on the same base station.
u The other handset can send and receive directory entries.
s ¢ q (select entry; page 41) ¢ §Menu§ ¢ Send Entry / Send List
~
Enter the internal number of the receiving handset and press §OK§.
A successful transfer is confirmed by a message and confirmation tone on the receiving
handset.
If you have sent a single entry, you can transfer another entry with §OK§.
Please note:
u Entries with identical numbers are not overwritten in the receiver handset.
u The transfer is cancelled if the phone rings or if the memory of the receiving handset is
full.
Copying a displayed number to the directory
You can copy numbers to the directory that are displayed in a list, e.g. the calls list or last
number redial list, to the directory.
A number is displayed.
§Menu§ ¢ Copy to Directory
¤ Complete the entry (page 40).
Copying a number from the directory
Version 2, 21.12.2006
You can open the directory in many operating situations e.g. to copy a number. Your
handset need not be in idle status.
s
Open the directory.
q
Select an entry (page 41).
42
CE 450 IP R / IM-Ost english / A31008-M1817-R601_1-7619 / directories_charges.fm / 02.03.2007
Last number redial list
Last number redial list
The last number redial list contains the ten numbers last dialled with the handset
(max. 32 numbers). If one of the numbers is in the directory, the corresponding name will
be displayed.
Open the last number redial list:
¤ With the handset in idle status, press the talk key c or handsfree key d.
Dialling from the last number redial list
c/d
q
c/d
Open the last number redial list.
Select an entry.
Press the talk/handsfree key. The number is dialled
Managing entries in the last number redial list
c/d
q
Open the last number redial list.
Select an entry.
Press the display key.
The following functions can be selected with q:
Use Number
(as in the directory, page 41)
Copy to Directory
Copying a displayed number to the directory (page 42).
Delete Entry
(as in the directory, page 41)
Delete List
(as in the directory, page 41)
Version 2, 21.12.2006
§Menu§
43
CE 450 IP R / IM-Ost english / A31008-M1817-R601_1-7619 / directories_charges.fm / 02.03.2007
Opening lists with the message key
Opening lists with the message key
You can use the message key f to open the following lists:
u Network mailbox, see page 47
Preconditions: Your network provider supports this function and the network mailbox is
configured for fast access (page 47).
u Calls list
An advisory tone sounds as soon as a new message arrives in a list. The message key f
flashes. In idle status, the display shows an icon for the new message.
Icon
New message...
Ã
... in the network mailbox
Á
... in calls list
The number of new entries is shown beneath the corresponding icon.
When you press the flashing key f, you will see all the lists that contain new messages.
If only one list contains new messages, this will be opened automatically.
Please note:
If calls are saved in the network mailbox you will receive a message if the appropriate settings have
been made (see the network mailbox instructions of your VoIP provider).
Calls list
Depending on the type of list set, the calls list contains
u all incoming and outgoing calls
u missed calls only
The numbers of the last 30 calls are saved.
Multiple calls from the same number will be stored once in the list of missed calls (the latest
call).
Multiple calls from the same number are stored several times in the list of answered calls.
Please note:
– Only calls to the receiving numbers assigned to a handset are stored in a handset's calls list
(page 100).
– If no receiving numbers are assigned, all calls will be stored in the calls list for all handsets.
The calls list is displayed as follows:
Calls List: 01+02
Version 2, 21.12.2006
Number of new entries + number of old, read entries
44
CE 450 IP R / IM-Ost english / A31008-M1817-R601_1-7619 / directories_charges.fm / 02.03.2007
Opening lists with the message key
Setting the calls list type
¢ Settings ¢ Base ¢ Calls List Type
Missed Calls / All Calls
Select and press §OK§ (‰ = on).
a
Press and hold (idle status).
The calls list entries are retained when you change the list type.
§Menu§
Opening the calls list
f ¢ Calls List: 01+02
q
Select entry.
The last incoming call is displayed in the calls list.
List entry
Example of a list entry:
New Call
1234567890
11.01.07
§Back§
U
01/02
19:27
§Menu
u Status of entry
In the calls list
New Call: new missed call.
Old Call: entry already read.
Call recv.: call taken.
u Entry number
01/02 means, for example: the first entry of a total of two entries.
u Number or name of caller
You can add the caller's number to the directory (page 42).
u Call date and time (if set, page 11).
Selecting from the calls list
Version 2, 21.12.2006
f ¢ Calls List: 01+02
q
Select entry.
c
Press the talk key.
45
CE 450 IP R / IM-Ost english / A31008-M1817-R601_1-7619 / directories_charges.fm / 02.03.2007
Opening lists with the message key
Managing entries in the calls list
Version 2, 21.12.2006
f ¢ Calls List: 01+02
q
Select entry.
§Menu§
Press the display key.
The following functions can be selected with q:
Delete Entry
As in the directory, page 41
Copy to Directory
Copy the number to the directory (page 42).
Show Name
If a URI (see page 145) was received and stored for a VoIP call, this will be shown. The
URI is dialled if you press the talk key c. The URI is not entered on the last number redial
list.
Press §OK§ / §Back§ to return to the list.
Show Connection
Indicates which of your phone numbers the caller has dialled.
Press §OK§ / §Back§ to return to the calls list.
Delete List
As in the directory, page 41
46
CE 450 IP R / IM-Ost english / A31008-M1817-R601_1-7619 / T-NetBox_SAG-registration.fm / 02.03.2007
Configuring the network mailbox for fast access
Using the network mailbox
Some VoIP providers offer answer machines on the network – network mailboxes.
You can use the relevant network mailbox if you have requested it from your VoIP provider.
The network mailbox only answers incoming calls made via the relevant line (VoIP phone
number). To record all calls, you should therefore set up network mailboxes for each VoIP
phone number.
Configuring the network mailbox for fast access
With fast access you can dial a network mailbox directly.
The network mailbox is preconfigured for fast access. You only need to enter the number
of a network mailbox.
Please note:
You can only set up fast access to one of the network mailboxes. You can assign a speed dial number
to the number for another network mailbox in the directory (e.g. the 2 key) (page 41). The speed dial
digit must be assigned for each handset.
Configuring the network mailbox for fast access and entering the network mailbox number
¢ Voice Mail ¢ Set Key 1
Select Network Mailbox and press §OK§ (‰ = activated).
~
Enter the network mailbox number and press §OK§.
The entry is saved.
a
Press and hold (idle status).
Fast access is automatically activated.
To deactivate fast access, you must delete the number.
This setting is now valid for all registered handsets.
§Menu§
Please note:
If no number has been entered: press and hold 1 to enter the number.
Calling the network mailbox
1
d
Press and hold. You are connected straight to the network mailbox.
If necessary, press the handsfree key. You hear the network mailbox announcement.
Please note:
If you have set an automatic area code (page 103), the area code is also prefixed to the number of
the network mailbox if it does not start with 0.
Version 2, 21.12.2006
Network mailbox message
The way in which you are informed of new messages in the network mailbox depends on
the relevant VoIP provider.
47
CE 450 IP R / IM-Ost english / A31008-M1817-R601_1-7619 / T-NetBox_SAG-registration.fm / 02.03.2007
Registering handsets
Using several handsets
Registering handsets
You can register up to six handsets to your base station.
Please note:
After registration, all the phone numbers for the phone will be assigned to the handset as receiving
numbers. It uses the first VoIP number as sending numbers. For how to change the assignments, see
page 100.
Registering another Gigaset C46 handset
Before you can use your handset, you must register it to a base station.
You must initiate handset registration on the handset and on the base station.
If the handset has been registered successfully you will see the display key §INT§ at the
bottom left of the idle display. If it does not appear, repeat the procedure.
On the handset
Menu§ ¢ Settings ¢ Handset ¢ Register Handset
~
Enter the system PIN of the base station (the default is 0000) and press §OK§.
The display shows e.g. Registering and Base flashes.
On the base station
÷
Within 60 sec. press and hold the registration/paging key on the base station
(page 1) (min. 1 sec.).
The handset is assigned the lowest available internal number (1-6). If several handsets are
registered to the base station, the internal number is shown in the display after registration, e.g. INT 2. This means that the handset has been assigned the internal number 2.
Please note:
Version 2, 21.12.2006
If six handsets are already registered to the base station, there are two options:
– The handset with the internal number 6 is in idle status: the handset you wish to register is
assigned the number 6. The handset that was previously number 6 is de-registered.
– The handset with the internal number 6 is being used: the handset you wish to register cannot be
registered.
48
CE 450 IP R / IM-Ost english / A31008-M1817-R601_1-7619 / T-NetBox_SAG-registration.fm / 02.03.2007
De-registering handsets
Registering other handsets
You can register other Gigaset handsets and handsets for other devices with GAP functionality as follows.
Please note:
Other handsets may not support all base station functions.
On the handset
¤ Start to register the handset as described in its user guide.
On the base station
÷
Press and hold (min. 1 sec.) the registration/paging key on the base station
(page 1).
De-registering handsets
You can de-register any registered C46 handset from any registered handset.
§INT§
Press the display key. All registered handsets are displayed.
q
Select the handset to be de-registered.
§Menu§
Press the display key.
De-register Handset
Select and press §OK§.
~
Enter the base station system PIN (default setting: 0000).
§OK§
Press the display key to confirm the prompt.
a
Press and hold (idle status).
The handset is de-registered immediately, even if it is not in idle status.
Version 2, 21.12.2006
Changing a handset's internal number
A handset is automatically assigned the lowest available number on registration. In the list
of internal subscribers, the handsets are sorted according to their internal number.
You can change the internal number of all registered handsets (1–6). Numbers 1-6 can
only be assigned once each.
§INT§
Press the display key.
§Menu§
Press the display key.
Edit Handset Number
Select and press §OK§.
q
Select handset.
~
Enter the number (1–6).
§OK§
Press the display key to complete the operation.
You will hear the error tone if an internal number has been allocated twice.
¤ Repeat the procedure with a free number.
49
CE 450 IP R / IM-Ost english / A31008-M1817-R601_1-7619 / T-NetBox_SAG-registration.fm / 02.03.2007
Changing the name of a handset
Changing the name of a handset
The names "INT 1", "INT 2" etc. are assigned automatically at registration. You can change
these names. The changed name is displayed in every handset's list.
§INT§
Press the display key.
q
Select handset.
§Menu§
Press the display key.
Change Handset Name
Select and press §OK§.
~
Enter name (max. 10 characters) and press §OK§.
Locating a handset ("paging")
You can locate your handset using the base station.
¤ Press the registration/paging key on the base station (page 1) briefly.
¤ All handsets will ring simultaneously ("paging"), even if the ringer tones are switched
off.
Ending paging
÷/c
Briefly press the registration/paging key on the base station (page 1) or press
the talk key on the handset.
Making internal calls
Internal calls to other handsets registered on the same base station are free.
Calling a specific handset
§INT§
qc
Or:
~
Press the display key.
Select handset and press the talk key.
Enter the number of the handset.
Calling all handsets ("group call")
Press the display key.
P
Press the star key.
Or:
Call All c Select and press the talk key.
§INT§
Ending a call
a
Press the end call key.
Version 2, 21.12.2006
Please note:
You can reject an internal call by pressing the end call key a.
50
CE 450 IP R / IM-Ost english / A31008-M1817-R601_1-7619 / T-NetBox_SAG-registration.fm / 02.03.2007
Making internal calls
Transferring a call to another handset
You can transfer an external call to another handset (connect).
§INT§
Press the display key.
The external participant hears the hold music.
q
Select handset or Call All and press §OK§.
When an internal participant answers:
¤ If necessary announce the external call.
a
Press the end call key.
The call is transferred. If the internal participant does not answer, or their phone is in use,
the call will automatically return to you.
Internal consultation calls
When speaking to an external participant you can call an internal participant simultaneously for consultation.
§INT§
Press the display key.
The external participant hears the hold music.
q
Select handset or Call All and press §OK§.
If the internal participant does not answer: press §Back§ to return to the external participant.
When an internal participant answers you can speak to them.
You have the following options:
Ending a consultation call
Press the display key.
Back
Select and press §OK§.
You are reconnected with the external participant.
§Menu§
Initiating a conference call
You are in an internal consultation call:
§Menu§
Press the display key.
Conference Call
Select and press §OK§.
The internal participant called can end the conference call by pressing the end call key a.
Accepting call waiting during an internal call
Version 2, 21.12.2006
If you receive an external call during an internal call, you will hear the call waiting tone
(short tone). With Calling Line Identification, the caller's number will appear in the display.
a
Press the end call key to end the internal call.
c
Press the talk key to take the external call.
51
CE 450 IP R / IM-Ost english / A31008-M1817-R601_1-7619 / settings_bs_hs_pabx.fm / 02.03.2007
Changing the display language
Handset settings
Your handset is preconfigured, but you can change the settings to suit your individual
requirements.
Changing the display language
You can view the display texts in different languages.
§Menu§ ¢ Settings ¢ Handset ¢ Language
The current language is indicated by ‰.
q
Select a language and press §OK§.
a
Press and hold (idle status).
If you accidentally choose a language you do not understand:
§Menu§
q
¢422
Press keys in sequence.
Select the correct language and press §OK§.
Setting the display
You have a choice of four colour schemes and several different contrasts. You can also set
a screensaver and backlight.
§Menu§ ¢ Settings ¢ Handset ¢ Display
You have the following options:
Screensaver
There are four different screensavers and No Screensaver or Digital Clock settings.
Colour Scheme
There are four colour schemes. When the backlight is switched off, the display is shown
in black and white regardless of the selected setting.
Contrast
There are five different contrast settings.
Backlight
In Charger / Without Charger determines whether the backlight stays on permanently or is
switched off after a certain time (‰ = permanently switched on).
Please note:
Version 2, 21.12.2006
If the backlight is switched on outside the charging cradle, the standby time for the handset is
considerably reduced!
52
CE 450 IP R / IM-Ost english / A31008-M1817-R601_1-7619 / settings_bs_hs_pabx.fm / 02.03.2007
Activating/deactivating auto answer
Activating/deactivating auto answer
When this function is activated, when a call arrives you can simply lift the handset out of
the charging cradle without having to press the talk key c.
§Menu§ ¢ Settings ¢ Handset
Auto Answer
Select and press §OK§ (‰ = on).
a
Press and hold (idle status).
Adjusting the loudspeaker volume
You can set the loudspeaker volume for handsfree talking to five different levels and the
earpiece volume to three different levels. You can only adjust the loudspeaker volume
during a call.
You are conducting an external call.
t
Press the control key.
q
Adjust the volume and press §OK§.
Please note:
The handsfree volume can only be adjusted when this function is set.
If t is assigned a different function e.g. toggling (page 39):
Open menu.
Volume
Select and press §OK§.
Make settings (see above).
§Menu§
Changing ringer tones
u Volume:
Version 2, 21.12.2006
Five volume levels (1–5; e.g. Volume 2 = ˆ) and "crescendo" ring ‰.
With "crescendo" ring, the volume gets louder with every ring.
u Melody:
There is a list of pre-loaded ringer melodies. The first three melodies are the "classical"
ring tones.
You can also set different ringer melodies for the following functions:
u External Calls: for external calls
u Internal Calls: for internal calls
u Alarm Clock: for the alarm clock
53
CE 450 IP R / IM-Ost english / A31008-M1817-R601_1-7619 / settings_bs_hs_pabx.fm / 02.03.2007
Advisory tones
Setting the ringer volume
The ringer volume is the same for all types of ring.
§Menu§ ¢ Audio Settings ¢ Ringer Volume
Or in idle status:
t
Press briefly.
Then:
q
Adjust the volume and press §OK§.
a
Press and hold (idle status).
Setting the ringer melody
Set different ringer melodies for external calls, internal calls and the alarm clock.
§Menu§ ¢ Audio Settings ¢ Ringer Melody
External Calls / Internal Calls / Alarm Clock
Select and press §OK§.
q
Select melody (‰ = on) and press §OK§.
a
Press and hold (idle status).
Activating/deactivating the ringer tone
You can turn off the ringer tone on your handset before you take a call or while the phone
is in idle status. You can take a call so long as it is displayed on the screen.
Deactivating the ringer tone
P
Press the star key and hold, until the Ú icon appears in the display.
Re-activating the ringer tone
P
Press and hold the star key in idle status.
Version 2, 21.12.2006
Advisory tones
Your handset uses "advisory tones" to tell you about different activities and statuses. You
can activate or deactivate the following tones:
u Advisory tones:
– Key click: every key press is confirmed.
– Confirmation beep (a rising tone sequence): at the end of the entry/setting, when
the handset is placed in the charging cradle and when a new entry arrives on the calls
list.
– Error tone (descending tone sequence): when you make an incorrect entry.
– Menu end tone: when scrolling at the end of a menu.
u Battery low beep: the battery requires charging.
You cannot deactivate the confirmation tone for placing the handset in the charging
cradle.
54
CE 450 IP R / IM-Ost english / A31008-M1817-R601_1-7619 / settings_bs_hs_pabx.fm / 02.03.2007
Using the handset as an alarm clock
Activating/deactivating advisory tones
§Menu§
¢ Audio Settings ¢ Advisory Tones
Select and press §OK§ (‰ = on).
All advisory tones are activated or deactivated.
Setting the battery low beep
§Menu§ ¢ Audio Settings ¢ Battery Low
On / Off / During Call
Select and press §OK§ (‰ = on).
The battery low beep is activated or deactivated or sounds during a call.
Using the handset as an alarm clock
Activating/deactivating the alarm clock
§Menu§
¢ Alarm Clock ¢ Activation (‰ = on)
After you activate the alarm clock, the menu for setting the wake up time opens automatically (page 55).
If the alarm clock is set, the wake up time appears with the l icon in the display instead of
the date.
Setting the wake up time.
§Menu§
~
¢ Alarm Clock ¢ Wake up time
Enter the wake up time in hours and minutes, then press §OK§.
When the alarm clock rings…
Alarm repeat after 5 minutes
Press the display key or any key.
If you press §Snooze§ three times the alarm clock switches off for 24 hours.
§Snooze§
Turning off the alarm clock for 24 hours
Version 2, 21.12.2006
§Off§
Press the display key.
55
CE 450 IP R / IM-Ost english / A31008-M1817-R601_1-7619 / settings_bs_hs_pabx.fm / 02.03.2007
Restoring the handset to the factory settings
Restoring the handset to the factory settings
Each individual handset setting is reset, in particular the language, display, volume, ringer
and alarm clock settings (see from page 52 onwards). The last number redial list is cleared.
Entries in the directory, the date and time, and the handset's registration to the base
station will be retained.
§Menu§ ¢ Settings ¢ Handset ¢ Reset Handset
§OK§
Press the display key to confirm.
a
Press and hold (idle status).
Cancel the reset with a.
Setting the base station
The base station settings are carried out using a registered Gigaset C46 handset.
Changing the system PIN of the base station phone
You will have to enter the system PIN e.g. when you register a handset with the base
station, change the VoIP settings or start the phone Web configurator.
You can change the base station's 4-digit default system PIN ("0000") to a 4-digit PIN
known only to yourself.
§Menu§ ¢ Settings ¢ Base ¢ System PIN
~
Enter the current system PIN and press §OK§.
~
Enter your new system PIN and press §OK§.
~
Now re-enter the new system PIN and press §OK§.
For security reasons, "****" is displayed instead of the numbers entered.
a
Press and hold (idle status).
Restoring the base station to the factory settings
The base station's phone and router will be reset.
Please note:
Version 2, 21.12.2006
You should carry out the following base station resets before giving your base station to a third party.
This will delete your personal data.
56
CE 450 IP R / IM-Ost english / A31008-M1817-R601_1-7619 / settings_bs_hs_pabx.fm / 02.03.2007
Activating/deactivating the on hold music
Resetting the base station via the menu
Each individual setting is reset, in particular:
u all router settings
u the router password
u VoIP settings such as VoIP provider and account data (page 61, page 90) and DTMF
settings (page 101)
u settings for the local network (page 59, page 87)
u the names of the handsets (page 50)
The calls list is cleared.
The date and time and the system PIN are retained. The handsets are still registered.
§Menu§ ¢ Settings ¢ Base ¢ Base Reset
§OK§
Press the display key to confirm.
Resetting the base station using a key on the base station
As with resetting the base station via the menu, each individual setting on the base station
phone is reset. The system PIN will also be reset to "0000" and all handsets registered
above and beyond the delivery scope are deregistered.
The router settings and router password are not reset.
Please note:
For how to reregister the handsets after resetting if necessary, see page 48.
¤ Remove the cable connection between the base station and modem.
¤ Remove the Ethernet cable from the base station's LAN socket.
¤ Remove the base station mains unit from the socket.
¤ Press and hold the registration/paging key (page 1).
¤ Plug the mains unit back into the power socket.
¤ Press and hold the registration/paging key (at least 10 sec.).
¤ Release the registration/paging key. The base station has now been reset.
Activating/deactivating the on hold music
¢ Settings ¢ Base
Music on hold
Select and press §OK§ to activate or deactivate the hold music (‰ = on).
§Menu§
Please note:
Version 2, 21.12.2006
Whether or not a caller hears the hold music during toggling or a consultation call depends on the
provider.
57
CE 450 IP R / IM-Ost english / A31008-M1817-R601_1-7619 / settings_bs_hs_pabx.fm / 02.03.2007
Activating/deactivating repeater mode
Activating/deactivating repeater mode
With a repeater you can increase the range and reception strength of your base station. You
will need to activate repeater mode. This will terminate any calls being made via the base
station at that time.
Precondition: A repeater is registered.
§Menu§ ¢ Settings ¢ Base ¢ Additional Features ¢ Repeater Mode
Select and press §OK§ (‰ = on).
Updating the base station phone's firmware
If necessary, you can update your base station phone's firmware.
The firmware update is downloaded directly from the Internet by default. The relevant
website is preconfigured in your phone.
As an alternative to uploading the firmware via the Internet, it can also be loaded from a
local PC. You can specify the PC via the phone Web configurator (page 106). This setting
applies only to the next firmware update.
Precondition:
The base station is in idle status, i.e.:
u no calls are being made.
u there is no internal connection between the registered handsets.
u no other handset has opened the base station menu.
Starting the firmware update manually
¢ Settings ¢ Base ¢ Firmware Update
~
Enter the base station system PIN (default setting: 0000).
The base station establishes a connection to the Internet or to the local PC.
§Yes§
Press the display key to start the firmware update.
§Menu§
Please note:
Version 2, 21.12.2006
– A firmware update can last up to 3 minutes. During the update, the handset loses the connection
to the base station. When the update has been successfully completed, the handset re-establishes
the connection to the base station.
– When updating from the Internet, checks are made to ensure that no newer version of the
firmware exists. If this is not the case, the operation is terminated and a message is issued to that
effect.
– If an error arises during a firmware update from a local PC, the most recent version of the firmware
is automatically downloaded from the Internet. Your phone should therefore be connected to the
Internet during every firmware update.
58
CE 450 IP R / IM-Ost english / A31008-M1817-R601_1-7619 / settings_bs_hs_pabx.fm / 02.03.2007
Setting the base station phone's IP address in LAN
Automatic firmware update
Precondition: The automatic version check is activated (page 107, default setting).
Your phone will check daily whether a newer firmware update is available via the Internet
on the Siemens configuration server. If this is the case, when the handset is in idle status
the message New firmware available! is displayed and the message key f flashes.
f
Press the message key.
§Yes§
Press the display key to confirm the prompt.
~
Enter the base station system PIN (default setting: 0000).
The firmware will be loaded onto your phone.
Please note that the firmware update may take up to 3 minutes.
Please note:
– If you reply to the request with §No§, the display will not be repeated. The message New firmware
available! will only be shown again if a newer version of the firmware than the one rejected is
available.
– You can deactivate the automatic version check via the Web configurator (page 107).
Making VoIP settings
For VoIP telephony you need to make the following settings:
u IP settings for the telephone connection to the LAN (to the router). You can make these
settings on the handset (page 59) or (if there is already a connection to the PC) via the
phone Web configurator (page 87).
u VoIP settings for each of your VoIP accounts (VoIP phone numbers). You can make the
settings for up to six VoIP accounts via the Web configurator.
Alternatively, you can also set and make changes to the first VoIP account (IP1, see
page 89) via the handset. You can make the settings with (page 61) or without
(page 61) connection assistants.
Setting the base station phone's IP address in LAN
The base station requires an IP address in order to be "recognised" by the LAN (the router).
The IP address can be assigned to the base station automatically (by the router) or manually.
u If performed dynamically, the router's DHCP server automatically assigns the base
station an IP address. The base station's IP address can be changed according to router
settings.
u If performed manually, you assign the base station a static IP address. This may be necessary depending on your network configuration.
Version 2, 21.12.2006
Please note:
For how to make the local network settings on the Web configurator, turn to page 87.
59
CE 450 IP R / IM-Ost english / A31008-M1817-R601_1-7619 / settings_bs_hs_pabx.fm / 02.03.2007
Setting the base station phone's IP address in LAN
Activating/deactivating dynamic assignment
¢ Settings ¢ Base ¢ Local Network
~
Enter the system PIN and press §OK§.
dynamic IP address (‰ = on)
Select and press §OK§ to change the current settings.
If you deactivate dynamic assignment, you must set the base station, default gateway and
DNS server IP address and subnet mask manually. A corresponding message is displayed.
§Menu§
Please note:
To assign the IP address dynamically, the DHCP server on the router must be activated (page 80).
Viewing/changing the phone's IP address
You can only change the IP address (page 140) if you have deactivated dynamic assignment.
192.168.1.2 has been preset by default.
§Menu§ ¢ Settings ¢ Base ¢ Local Network (enter system PIN) ¢ IP Address
The current IP address is displayed.
~
If necessary, enter the IP address and press §OK§.
Please note:
For notes on the IP address, please see page 87 and the glossary on page 140.
Viewing/changing the subnet mask
You can only change the subnet mask (page 144) if you have deactivated dynamic assignment.
255.255.255.0 has been preset by default.
§Menu§ ¢ Settings ¢ Base ¢ Local Network (enter system PIN) ¢ Subnet Mask
The current subnet mask is displayed.
~
If necessary, enter the subnet mask and press §OK§.
Please note:
Version 2, 21.12.2006
For notes on the subnet mask, please see page 87 and the glossary on page 144.
60
CE 450 IP R / IM-Ost english / A31008-M1817-R601_1-7619 / settings_bs_hs_pabx.fm / 02.03.2007
Entering/changing the first VoIP account with the connection assistant
Viewing/changing the DNS server
Enter the IP address for the preferred DNS server. The DNS server (Domain Name System)
converts the symbolic name of a server (DNS name) into the public IP address for the server
when the connection is made.
You can specify your base station router's IP address here. The router forwards phone
address requests to its DNS server.
The default is 192.168.1.1.
§Menu§ ¢ Settings ¢ Base ¢ Local Network (enter system PIN) ¢ DNS Server
~
If necessary, enter the IP address of your preferred DNS server and press §OK§.
Viewing/changing the default gateway to the Internet
Enter the IP address for the standard gateway, by means of which the local network is connected with the Internet. That is usually the local (private) IP address for your base station
router (default 192.168.1.1). Your phone requires this information to be able to access the
Internet.
The default is 192.168.1.1.
§Menu§ ¢ Settings ¢ Base ¢ Local Network (enter system PIN) ¢ Default Gateway
Entering/changing the first VoIP account with the connection assistant
The connection assistant starts automatically the first time your handset and base station
are used. You can also start the connection assistant via the menu:
§Menu§ ¢ Settings ¢ Base ¢ Telephony ¢ Connection Assistant
For how to enter VoIP settings for the first VoIP account using the connection assistant, see
page 18.
Entering/changing the first VoIP account without the connection
assistant
For your first account you can change your provider's general VoIP settings and your personal VoIP user data via the menu without starting the connection assistant.
Downloading settings for the first VoIP provider
§Menu§
¢ Settings ¢ Base ¢ Telephony ¢ VoIP (enter system PIN) ¢ Select VoIP Provider
Version 2, 21.12.2006
The phone establishes a connection with the Siemens configuration server on the Internet.
q
Select country and press §OK§.
q
Select VoIP provider and press §OK§.
Your VoIP provider data is downloaded and saved in your phone.
If errors occur during a download, see page 113.
61
CE 450 IP R / IM-Ost english / A31008-M1817-R601_1-7619 / settings_bs_hs_pabx.fm / 02.03.2007
Entering/changing the first VoIP account without the connection assistant
Please note:
If your VoIP provider is not included in the list, you need to enter or adjust the general VoIP settings
manually via your phone's Web configurator, see page 92.
Automatic update for the VoIP provider settings
Precondition: The automatic version check is activated (page 107, default setting).
After the first download of the VoIP provider settings, your phone will check daily whether
a newer version of the files for your VoIP provider is available via the Internet on the
Siemens configuration server. If there is an update for one of your VoIP providers, the
message New profile available! will be displayed when the handset is in idle status, and the
message key f flashes.
f
Press the message key.
§Yes§
Press the display key to confirm the prompt.
~
Enter the system PIN and press §OK§.
The new VoIP provider data is downloaded and saved in your phone.
Please note:
– The version check relates to all VoIP providers whose data you have downloaded from the Internet.
– If you reply to the request with §No§, the display will not be repeated. The message New profile
available! will only be shown again if a newer version of the VoIP settings than the one rejected is
available.
– You can deactivate the automatic version check via the Web configurator (page 107).
Entering/changing the VoIP user data for the first VoIP account
The VoIP settings must also be extended for your personal data. You will receive all necessary data from your VoIP provider.
Please note:
When making these entries, please remember the VoIP user data is case sensitive. For how to enter
text see page 124.
¢ Settings ¢ Base ¢ Telephony ¢ VoIP
~
Enter the system PIN and press §OK§.
Username / Authentication Name / Authentication Password
Select and press §OK§.
~
Enter/change the user data and press §OK§.
Enter the caller ID for your VoIP provider account as the Username. The Username is mainly
identical to your Internet phone number (the first part of your SIP address see page 91).
For Authentication Name and Authentication Password enter the provider-dependent access
data that has to be transferred by the phone to the SIP service at registration.
Tip: A previously set password is not displayed.
Version 2, 21.12.2006
§Menu§
62
CE 450 IP R / IM-Ost english / A31008-M1817-R601_1-7619 / settings_bs_hs_pabx.fm / 02.03.2007
Activating/deactivating display of VoIP status codes
Activating/deactivating display of VoIP status codes
If the function is activated, a VoIP status code for your service provider is displayed.
Activate the function e.g. if you have problems with VoIP connections. You will receive a
provider-specific status code, which supports the service when the problem is analysed.
§Menu§ ¢ Settings ¢ Base ¢ Telephony ¢ VoIP
~
Enter the system PIN and press §OK§.
Status on HS (‰ = on)
Select and press §OK§.
Please note:
– For how to make the setting on the Web configurator, see page 108.
– A table with possible status codes and their meaning can be found in the appendix on page 116.
Checking the base station phone's MAC address
Version 2, 21.12.2006
Depending on your network configuration, you may have to enter your base station
phone's MAC address, for example,into your router's access control list. You can check your
base station phone's MAC address:
§Menu§ ¢ 4 I O 2 Q
Your base station phone's MAC address will be displayed.
a
Press and hold (idle status).
63
CE 450 IP R / IM-Ost english / A31008-M1817-R601_1-7619 / web_server.fm / 02.03.2007
Configuring the base station router and phone via a PC
Using the Web configurators
You can manage your Gigaset CE 460 IP R via your PC's Web browser with two Web
configurators:
u Use the router Web configurator to make the settings for your base station router.
u Use the phone Web configurator for the settings for your base station phone.
Please note:
Depending on your VoIP provider, it is possible that you will be unable to change individual settings
in the Web configurator.
Configuring the base station router and phone via a PC
Preconditions:
u A standard Web browser is installed on the PC, e.g. Internet Explorer version 6.0 or
higher, or Firefox version 1.0.4 or higher.
u The base station and PC are connected to each other.
Please note:
– The phone is not locked while you make settings for one of the Web configurators. You can also
use your phone to make calls or change base station or handset settings on your handset at the
same time.
– While you are connected to the Web configurator, it is blocked to other users. It cannot be accessed
by more than one user at any time.
The router Web configurator offers the following options:
u Start the wizard for the basic router settings and the connection to the Internet
u Configure your router access to the local network (IP address, gateway to the Internet).
u Define the data server for firmware updates and load new firmware onto the router if
necessary.
u Obtain information about your router's status (firmware version, MAC address andso
on).
The phone Web configurator offers the following options:
u Configure your phone access to the local network (IP address, gateway to the Internet).
u Configure your phone for VoIP.
u Define the data server for firmware updates and load new firmware onto the phone if
necessary.
u Copy contacts from the Outlook address book on your PC into the handset directories or
back up your handset's directories on your PC.
u Obtain information about your phone's status (firmware version, MAC address andso
Version 2, 21.12.2006
on).
64
CE 450 IP R / IM-Ost english / A31008-M1817-R601_1-7619 / web_server.fm / 02.03.2007
Starting the Web configurator
Starting the Web configurator
Precondition: The settings of an available firewall allow the PC and base station to communicate with each other.
You need to establish a connection with the PC Web browser to the respective Web configurator (router Web configurator or phone Web configurator) to be able to access the functions of both Web configurators.
Once you have successfully established the connection, the Web browser will display a Web
page for registration and this will ask you to authenticate yourself by entering a system PIN.
The Home for the selected Web configurator will be displayed once you have registered successfully.
You can find the detailed description of the start and registration procedure on page 69
(router Web configurator) or page 85 (phone Web configurator).
Please note:
– The base station router and the base station phone have passwords or system PINs that are independent of one another. Changing the password for the base station router will not affect the system PIN for the phone and vice versa.
– If you have forgotten your password or your system PIN, you will have to reset your base station
to the factory settings. Please note that this will restore all other settings too (page 57).
– If you do not make any entries for a lengthy period (around 10 minutes), you will be automatically
logged off. The next time you try to make an entry or open a Web page, the Login Web page will
be displayed. Enter the system PIN again to log in again.
– Entries that had not yet been saved in the router or on the phone before automatic log-off are lost.
Logging off
In the menu bar at the top right of every Web page in the Web configurator, you will see
the Log Off command (page 66). Click Log Off to log off from the Web configurator.
Warning:
Version 2, 21.12.2006
Always use the Log Off command to end the connection to the Web configurator. If, for example, you
closethe Web browser without logging off first, it is possible that access to the Web configurator will
be blocked for a few minutes.
65
CE 450 IP R / IM-Ost english / A31008-M1817-R601_1-7619 / web_server.fm / 02.03.2007
Structure of the Web pages
Structure of the Web pages
The Web pages contain the UI elements displayed in Figure 2.
Navigation area
Working area
Buttons
Menu bar
Figure 2 Example of the structure of a Web page
Menu bar
In the menu bar, the Web configurator menus are depicted in the form of tab pages.
The following menus are available in this example:
u Home
u Settings
u Status
If you click a menu that contains subfunctions (in this example the Settings menu), then
these will be displayed in the navigation area.
You will find the Log Off function to the right of the menu bar on every Web page (page 65).
Please note:
Version 2, 21.12.2006
You will find an overview of the Web configurator menu on page 27.
66
CE 450 IP R / IM-Ost english / A31008-M1817-R601_1-7619 / web_server.fm / 02.03.2007
Structure of the Web pages
Navigation area
The functions of the menu selected in the menu bar are listed in the navigation area.
If you click a function, the associated page opens in the working area with information and/
or fields for your inputs.
If a function is assigned subfunctions, these are displayed with the function as soon as you
click the function. The relevant page for the first subfunction is displayed in the working
area.
Working area
Depending on the function selected, information or dialogue boxes are displayed in the
working area, which allow you to make or change your phone settings.
Making changes
Make settings for entry fields, lists or options.
u There may be restrictions regarding the possible values for a field, e.g. entering special
characters or certain value ranges.
u To open a list, click
. You can choose between default values.
u There are two kinds of options:
– Options in a list, from which you can activate one or several options. Active, i.e.
selected options are highlighted with , non-active options with . You can activate an option by clicking on . The status of the other options in the list does not
change. You can deactivate an option by clicking on .
– Alternative options. The active option in the list is highlighted with
, and the nonactive with . You can activate an option by clicking on . The previously activated
option is deactivated. You can only deactivate an option by activating another option.
Applying changes
As soon as you have made your change on a page, activate the new setting in the router or
on the phone by clicking on Set.
If your input in a field does not comply with the rules for this field, an appropriate error
message will be displayed. You can then repeat the input.
Warning:
Version 2, 21.12.2006
Changes that have not been saved in your router or phone are lost if you move to another Web page
or if the connection to the Web configurator is terminated, e.g. due to exceeding the time limit
(page 65).
67
CE 450 IP R / IM-Ost english / A31008-M1817-R601_1-7619 / web_server.fm / 02.03.2007
Opening Web pages
Buttons
Buttons are displayed in the bottom section of the working area.
Set
Save entries on the phone.
Cancel
Reject changes made on the Web page and reload the settings that are currently saved
in your phone to the Web page.
Opening Web pages
A brief outline of the navigation to the individual Web configurator functions is given
below.
Example:
Version 2, 21.12.2006
Setting DTMF signalling with the phone Web configurator
Settings ¢ Telephony ¢ Advanced Settings
To open the Web page, carry out the following steps after registration:
¤ Click the Settings menu in the menu bar.
¤ Click the Telephony function in the navigation area.
The subfunctions of Telephony are displayed in the navigation tree.
¤ Click the Advanced Settings subfunction.
The Web page from Figure 2 will be shown in the Web browser.
68
CE 450 IP R / IM-Ost english / A31008-M1817-R601_1-7619 / web_server.fm / 02.03.2007
Connecting the PC to the router Web configurator
Router Web configurator
You can use the router Web configurator to configure the base station router.
u Save your Internet access data (page 71) and the address for your DNS server (page 78)
on your router.
u Activate and configure NAT (page 75) and firewall for the router (page 74).
u Activate the Quality of Service for the router (page 78).
u Activate/deactivate the DHCP server for your router (page 80).
u Select the time server and time zone (page 81).
u Make the settings for the remote management of the router (page 82) and change the
router password (page 82).
u Load the firmware updates onto the router.
Connecting the PC to the router Web configurator
Precondition: The settings of an available PC firewall allow the PC and base station to communicate with each other.
¤ Launch the Web browser on your PC.
¤ In the Web browser address field, enter the IP address or name of the base station
¤
router, e.g.
http://192.168.1.1 or http://router.gigaset (default setting)
Press the return key.
A connection is established to the base station router's Web configurator.
Please note:
You can find out how to change the name router.gigaset on page 81.
Login
Version 2, 21.12.2006
Once you have successfully established the connection, the Login Web page will be
displayed in the Web browser.
The language in which the menus and the dialogues for the router Web configurator are
displayed is preset by the firmware.
¤ Enter the password for your base station router in the bottom field of the Web page
(default setting: 0000) to access the router Web configurator functions.
¤ Click OK.
Once you have successfully logged in, a Home opens with general information on the Web
configurator.
69
CE 450 IP R / IM-Ost english / A31008-M1817-R601_1-7619 / web_server.fm / 02.03.2007
Login
Please note:
– If you have forgotten your password or your system PIN, you will have to reset your base station
to the factory settings. Please note that this will restore all other settings too (page 57).
– If you do not make any entries for a lengthy period, you will be automatically de-registered. The
next time you try to make an entry or open a Web page, the Login Web page will be displayed.
Enter the system PIN again to log in again. This time is set to 30 min. in the default settings. You
can change it (page 82).
– Entries that had not yet been saved before automatic log-off are lost.
Menu bar
Version 2, 21.12.2006
The following menus are available in the router Web configurator:
u Home
The start screen is opened once you have registered with the Web configurator. It contains information on the Web configurator menus.
u Basic Setup Wizard (page 85)
You can start a wizard to connect the base station router to the Internet via this menu
(page 15).
u Router Settings (page 69)
This menu allows you to make settings on your base station router. The Router Settings
menu comprises the function areas Internet, Local Network and Administration.
u Telephony Settings
You can use this menu to start the phone Web configurator (page 85), to make settings
on the base station phone.
u Status (page 84)
This menu gives you information about your phone.
70
CE 450 IP R / IM-Ost english / A31008-M1817-R601_1-7619 / web_server.fm / 02.03.2007
Internet – configuring the connection to the Internet.
Internet – configuring the connection to the Internet.
If you have configured the router for your Gigaset CE 460 IP R using the wizard for the basic
settings, then you will also have configured the WAN connection (Internet access). You can
check, change or extend these settings in the Internet menu.
Under Internet you can also find functions for security settings and limiting access to the
Internet as well as for providing your own services on the Internet.
You can use the Internet menu to make the following settings for the Internet:
u check and edit the Internet access data (page 71),
u secure your local network against external hacker attacks and restrict access to Internet
pages for subscribers in the local network (see Firewall, page 74),
u provide your own services on the Internet and restrict access from the Internet to the
local network (see NAT, page 75),
u enter addresses for the DNS server used (page 78),
u define QoS properties (Quality of Service, see page 78), i.e. prioritise the transfer of
VoIP data and thus improve the voice quality for VoIP connections.
Connection – entering access data for the Internet connection
You can use the Connection Web page to set up or change the configuration for your Internet connection. Any settings that you make here must correspond with the information
from your Internet provider. False information can lead to problems with your Internet connection.
The procedure for entering or changing the settings for Internet access is as follows:
¤ Open the following Web page: Router Settings ¢ Internet ¢ Connection.
The settings for the Internet connection that are currently stored in the base station will
be displayed.
¤ First select the WAN connection type from the Connection list. The connection type
¤
¤
Version 2, 21.12.2006
¤
¤
depends on what kind of Internet connection you have and the agreements with your
Internet provider. The access data received from your Internet provider for registration
shows you which connection type you must select.
The options are PPPoE, Static IP Address, Dynamic IP Address and PPTP.
Enter the access data required for the connection type (see below).
In the Upstream Rate field, enter the maximum amount of your Internet connection's
bandwidth that should be available for data uploads. First enter the upload stream rate
given by your Internet provider. Carry out tests to check that calls can also be made with
good voice quality at the same time as data is being uploaded and adjust the rate
accordingly (page 78).
Click Set to apply the settings.
Below is an explanation of the information that you must make dependent on
Connection:
71
CE 450 IP R / IM-Ost english / A31008-M1817-R601_1-7619 / web_server.fm / 02.03.2007
Connection – entering access data for the Internet connection
Connection = PPPoE
The protocol PPPoE (Point-to-Point-Protocol over Ethernet) is used by many Internet providers. It allows several subscribers in a local network to access the Internet via a single Internet account. The Internet provider assigns your router a password and, if necessary, a user
name.
User Name
If you have received a user name from your Internet provider, enter this name
here. Not all Internet providers require a user name. If this is the case, leave this
field empty.
Password, Confirm new password
In the Password field, enter the password agreed with the Internet provider and
repeat it in the Confirm new password field.
MTU
The MTU (Maximum Transmission Unit) defines the maximum length of a data
packet that can be carried over the Internet at one time. The standard value is
1492 bytes. Depending on the provider, there may be restrictions for the packet
size. You should then modify the value accordingly.
Please note:
For the Internet connection via PPPoE, your router is set so that it is permanently connected with the
Internet. This means that you can always be reached for VoIP calls.
Connection = Static IP Address
Version 2, 21.12.2006
A static IP address is assigned to the router. This is permanently assigned to your router as
a public IP address (page 142). The router needs the following data for the Internet access:
IP Address, Subnet Mask
Enter the static IP address and subnet mask given to the router by your Internet
provider.
If the base station router is connected to the Internet via another local network
(LAN), then enter the private IP address for your router in this LAN and the subnet mask for the LAN.
Gateway
Enter the IP address of the gateway that connects your router with the Internet.
If the connection is via another LAN, enter the private IP address for the router
or gateway that is used to connect this LAN with the Internet here.
72
CE 450 IP R / IM-Ost english / A31008-M1817-R601_1-7619 / web_server.fm / 02.03.2007
Connection – entering access data for the Internet connection
Connection = Dynamic IP Address
The router is assigned an Internet address dynamically. This IP address is only temporarily
assigned to the router. It can change. No more data must be entered for this connection
type.
This connection type is frequently used for Internet connection via another LAN.
The following data is displayed on the Web page:
IP Address, Subnet Mask
The IP address that is currently assigned to the router, and the corresponding
subnet mask.
Gateway
The IP address for the router or gateway computer that connects the router to
the Internet.
DHCP Server
The IP address server that assigns the IP address to the router.
Connection = PPTP
Version 2, 21.12.2006
The PPTP protocol (Point-to-Point Tunnelling Protocol) allows a secure connection to a
remote private network (e.g. from home to your company network) via the Internet. Your
router is part of a Virtual Private Network (VPN). The data is sent via the Internet in a secure
and encrypted connection (tunnel).
The following data is required for access to the remote network:
IP Address, Subnet Mask
Enter the IP address and subnet mask given to the router by your Internet provider.
Gateway
Enter the IP address of the gateway that connects your router with the Internet.
VPN Server Enter the IP address of the VPN server (Virtual Private Network). The VPN server
is the gateway to the remote network. Your Internet provider will supply you
with the IP address.
User Name
Enter the user identification that your router must enter when logging on to
the remote network.
Password, Confirm new password
In the Password field, enter your registration password and repeat it in the
Confirm new password field.
MTU
The MTU (Maximum Transmission Unit) defines the maximum length of a data
packet that can be carried over the Internet at one time. The standard value is
1492 bytes. Depending on the provider, there may be restrictions for the packet
size. You should then modify the value accordingly.
73
CE 450 IP R / IM-Ost english / A31008-M1817-R601_1-7619 / web_server.fm / 02.03.2007
Setting up the Firewall
Setting up the Firewall
Your router's integrated firewall monitors and limits the exchange of data between subscribers of your local network and the Internet. Activating the firewall does not affect the
router's performance.
When the firewall is activated you can:
¤ protect your network against hacker attacks,
¤ restrict Internet access for individual PCs in your local network (IP Filter, MAC Filter).
The firewall functions are activated and configured by default. Do the following to change
the settings for the firewall:
¤ Open the following Web page: Router Settings ¢ Internet ¢ Firewall.
¤ Highlight On or Off in the Firewall field to activate or deactivate the firewall.
¤ Click Set to apply the settings.
Attack Detection
When the firewall is activated, you can also switch attack detection on or off.
¤ Highlight the desired setting in the Attack Detection field.
¤ Click Set to apply the settings.
IP Filter
When the firewall is activated, you can restrict access to the Internet for certain PCs in your
local network based on their IP address.
Create a list of the PCs and the applications (defined by their port number on the PC) that
you want to allow access to the Internet.
¤ Open the following Web page: Router Settings ¢ Internet ¢ Firewall ¢ IP Filter.
¤ Enter the IP address of the PC in the IP Address field.
¤ In the Port Range fields, enter the first and last port number of the port area on the PC
that you do not want to have access to the Internet.
¤ Select the protocol used from the Protocol list and click Add.
¤ Repeat the previous step if there are further PCs or applications that you do not want to
allow access to the Internet.
¤ Click Set to apply the settings.
Please note:
Version 2, 21.12.2006
– Deactivate the Enabled field to give a specified PC temporary access.
– Click Delete to permanently remove a PC from the list.
74
CE 450 IP R / IM-Ost english / A31008-M1817-R601_1-7619 / web_server.fm / 02.03.2007
Setting up NAT
MAC Filter
When the firewall is activated, you can restrict access to the Internet for certain PCs and PC
applications based on their MAC address.
¤ Open the following Web page: Router Settings ¢ Internet ¢ Firewall ¢ MAC Filter.
¤ In the fields for MAC Address, enter the MAC address for the PC that you do not want to
have access to the Internet and click on Add.
¤ Repeat the previous step if there are further PCs that you do not want to allow access to
the Internet.
¤ Click Set to apply the settings.
Please note:
– Deactivate the Enabled field to give a specified PC temporary access.
– Click Delete to remove a PC from the list.
Setting up NAT
NAT (Network Address Translation) allows several subscribers (PCs) in their local network
to access the Internet via a public IP address. NAT also protects the subscribers in their local
network against direct unauthorised access from the Internet.
They can, however, forward requests from the Internet specifically to PCs or applications in
their local network if they use special applications, or if they operate a server in their local
network (Port Forwarding / Exposed Host).
Activating/deactivating NAT:
¤ Open the following Web page: Router Settings ¢ Internet ¢ Address Translation (NAT).
¤ Highlight On or Off in the Address Translation (NAT) field to activate or deactivate NAT.
¤ Click Set to apply the settings.
Version 2, 21.12.2006
If NAT is activated, the following functions are displayed in the navigation tree for the NAT
configuration, and these can be used to control communication between the local network
and the Internet:
u Port Forwarding (page 76),
u Port Mapping (page 77),
u Exposed Host (page 77) and
u UPnP (page 78)
75
CE 450 IP R / IM-Ost english / A31008-M1817-R601_1-7619 / web_server.fm / 02.03.2007
Setting up NAT
Port Forwarding
Port forwarding enables you to make services from applications in your local network available to Internet users as well. The router can use a specific port to automatically forward
incoming requests from the Internet to a PC in the local network and thus set up a virtual
server, for example to publish your Internet page on your own Web server.
Internet services are generally addressed via defined port numbers. The router requires a
mapping table for the port numbers in order to divert the service requests to a PC that
actually provides the service. You can create these on this Web page.
Precondition: NAT is activated.
¤ Open the following Web page: Router Settings ¢ Internet ¢ Address Translation (NAT)
¢ Port Forwarding.
¤ Select a service from the Predefined Applications list.
¤ In the Local IP Address column, enter the private IP address for the PC to which the
requests should be forwarded and click Add.
¤ Repeat the previous step as necessary for further port forwarding.
If the required service is not in the list, you will have to enter the port forwarding manually.
¤ Select the protocol used by the service from the Protocol list.
¤ Enter the port number for the service under Public Port.
¤ Under Local Port enter the number ports on the PC to which the service requests should
be forwarded.
¤ Enter the IP address for the PC in the local network in the Local IP Address field.
¤ Repeat the previous step as necessary for further port forwarding.
¤ Click Set to apply the settings.
Please note:
Version 2, 21.12.2006
– Deactivate the Enabled field to temporarily deactivate the port forwarding.
– Click Delete to remove a forwarding action from the list.
– If you want operate your base station phone's Web configurator from a different network
remotely, you have to forward the HTTP port 80 (Public Port) to the port 80 (Local Port) of the base
station phone, and permit remote management on the phone Web configurator (page 88).
76
CE 450 IP R / IM-Ost english / A31008-M1817-R601_1-7619 / web_server.fm / 02.03.2007
Setting up NAT
Port Mapping
Port mapping is essentially an automatic form of port forwarding. It involves ports being
released on the router for a PC in the local network, and the PC "manages" these ports itself.
The router allows messages received by these ports through in both directions.
¤ Open the following Web page: Router Settings ¢ Internet ¢ Address Translation (NAT)
¢ Port Mapping.
Precondition: NAT is activated.
¤ In the Server IP fields, enter the local IP address for the PC in the local network.
¤ Enter a port, a port area (e.g. 2345 - 2678) and/or a series of ports (6006, 8005) in Port
¤
¤
¤
Mappings.
Example of an entry in Port Mappings: 2345 - 2678, 6006, 8005
Click Add.
Repeat the previous step if necessary.
Click Set to apply the settings.
Please note:
– Deactivate the Enabled field to temporarily deactivate the settings for a PC.
– Click Delete to remove a PC from the list.
Exposed Host
If NAT is activated, you can set up a PC in your local network as an exposed host. Your router
will then forward all incoming data traffic from the Internet to this client. You can then, for
example, operate your own Web server on one of the PCs in your local network and make
it accessible to Internet users.
Please note: Exposed host means that your local PC is directly visible on the Internet, and
is therefore exposed to particular dangers (e.g. from hacker attacks). You should only activate this function if absolutely necessary (e.g. to operate a Web server) and if other functions (e.g. port forwarding) are not adequate. In this case you should take appropriate
measures on the clients concerned.
¤ Open the following Web page: Router Settings ¢ Internet ¢ Address Translation (NAT)
¢ Exposed Host.
¤ Highlight On or Off in the Exposed Host field.
¤ If you activate the function, enter the local IP address for the PC that you want to release
as exposed host in the Local IP Address field.
Version 2, 21.12.2006
¤ Click Set to apply the settings.
77
CE 450 IP R / IM-Ost english / A31008-M1817-R601_1-7619 / web_server.fm / 02.03.2007
DNS – entering the DNS server
UPnP
If you activate UPnP (Universal Plug and Play) on your router, then PCs in your local network
that have UPnP installed in their operating system can offer their own services on the Internet, and also automatically use services offered on the Internet.
¤ Open the following Web page: Router Settings ¢ Internet ¢ Address Translation (NAT)
¢ UPnP.
¤ Highlight On or Off in the UPnP field.
¤ Click Set to apply the settings.
DNS – entering the DNS server
DNS (Domain Name System) is a decentralised database on the Internet that assigns userfriendly symbolic names (domains) to the public IP addresses for computers and services.
Access to this database requires DNS servers that convert the DNS name into the IP address
when the connection is established to a computer/server. DNS servers are normally provided automatically by your Internet provider and do not need to be set up additionally.
The DNS server that you enter here will only be used if your provider does not make a DNS
server available.
¤ Open the following Web page: Router Settings ¢ Internet ¢ DNS.
¤ Activate the use of a user-friendly DNS server for your Internet connection by entering
its IP address in the Preferred DNS Server field.
¤ In the Alternate DNS Server field enter the IP address of a server that should be used if the
preferred server is not available.
¤ Click Set to apply the settings.
QoS – setting the Quality of Service, prioritising VoIP
Version 2, 21.12.2006
Many communication and multimedia applications require high speed and large bandwidths to transfer data between the local network and the Internet. However, for many
applications there is often only one Internet connection with limited capacity available.
QoS (Quality of Service) divides this capacity between the different applications and provides undelayed, continuous data transfer where data packets with higher priority
(e.g. VoIP) are given transmission preference.
¤ Open the following Web page: Router Settings ¢ Internet ¢ QoS.
¤ In the Upstream Rate field indicate the maximum bandwidth for your Internet connection
that should be available for uploads.
¤ Click Set to apply the settings.
78
CE 450 IP R / IM-Ost english / A31008-M1817-R601_1-7619 / web_server.fm / 02.03.2007
Setting Routing
Allocating VoIP connections the optimum bandwidth
You can find the optimum setting for Upstream Rate by carrying out tests while making a
phone call during a data upload.
First, in the Upstream Rate field enter the upload stream rate given by your Internet provider.
Then proceed as follows:
¤ Make a phone call while you upload data.
¤ If the voice quality is already good: increase the value in the Upstream Rate field step by
step, provided that the voice quality is still good. This means that you won't "give away"
any bandwidth.
If the voice quality is poor: reduce the value in the Upstream Rate field step by step until
the voice quality is good.
Setting Routing
You can enter static routings in the table. The routing establishes which path the data packets should follow to reach a specific target in your network. This means, for example, that
you can allow users from various IP domains to access the Internet via your router.
¤ Open the following Web page: Router Settings ¢ Internet ¢ Routing.
¤ In the Destination Network field enter the address of the server to which the data packets
are addressed.
¤ In the Gateway and Subnet Mask fields enter the address of the gateway computer or
router in your local network that is used to reach the target server.
¤ Repeat the previous step as necessary for further routing entries.
¤ Click Add.
¤ Click Set to apply the settings.
Example: Your router does not have a direct connection to the Internet, but requests to a
server on the Internet are forwarded via another local network. Your router is connected to
this network via another router (=gateway). In your router's routing table, you have to
enter the IP address of the server on the Internet for Destination Network, and the private
address of the other router within your local network for Gateway.
Routing Table
Version 2, 21.12.2006
The routing table displays all the rules used in your router for forwarding data packets
within your local network.
¤ Open the following Web page: Router Settings ¢ Internet ¢ Routing ¢ Routing Table.
79
CE 450 IP R / IM-Ost english / A31008-M1817-R601_1-7619 / web_server.fm / 02.03.2007
Configuring the local network
Configuring the local network
You can use the LAN configuration to define a private IP address for the router and to configure the LAN DHCP server.
Defining the router's private IP address
¤ Open the following Web page: Router Settings ¢ Local Network.
You can change the IP address for the base station router on this page. The default IP
address is 192.168.1.1. This is the router's private IP address (LAN address). This is the IP
address under which the base station router can be reached on the local network. This IP
address can be freely assigned from the block of addresses that is reserved for private use.
The IP address under which the router can be reached from outside is assigned by the Internet provider.
¤ If you want to assign the router a different IP address, enter it in the fields for IP Address.
We recommend using an IP address from a block that is reserved for private use. This
address block is 192.168.1.1 – 192.168.255.254.
¤ Enter the values in the fields for Subnet Mask (page 144).
For IP addresses from the address block 192.168.0.1 – 192.168.255.254 the subnet
mask 255.255.255.0 is generally used. This is preconfigured when the phone is supplied. A subnet mask 255.255.255.x means that the first three parts of the IP addresses
for all devices in the router's local network (base station phone and the device connected to the LAN connection) must match.
Configuring the DHCP server
The router has a DHCP server whose factory setting is active. The IP addresses for the PCs
and the phone are automatically assigned by the router, provided that DHCP is also activated on the PCs and the phone.
¤ To activate the DHCP server, select On in the DHCP Server field.
¤ If the DHCP server is active, you have to specify a block of IP addresses that the router is
to use for automatically assigning the IP addresses to the PCs. Define the First issued IP
Address and the Last issued IP Address.
Please note:
– The address block is not allowed to contain the router's private IP address (default setting:
192.168.1.1).
– If the DHCP server for the router is activated, you can configure the network setting on the PCs so
that the option Obtain an IP address automatically is set on the PCs.
– If you deactivate the DHCP server, you have to assign the PCs a static IP address from your router's
IP address block via the network settings.
– The phone and PCs retain the dynamically assigned IP address until the router is next rebooted.
The allocation is done again each time the router is rebooted.
Applying the settings for the local network
Version 2, 21.12.2006
¤ Click Set to apply the settings.
The base station router is rebooted to activate the settings. The reboot can take several
minutes (depending on the provider). Do not disconnect your base station from the PC or
the power supply during this period.
80
CE 450 IP R / IM-Ost english / A31008-M1817-R601_1-7619 / web_server.fm / 02.03.2007
Defining the router's name and domain
Displaying DHCP Clients
¤ Open the following Web page: Router Settings ¢ Local Network ¢ DHCP Clients.
A list will be displayed of all subscribers (PCs etc.) in your local network that have been
assigned a dynamic IP address. The MAC address, the IP address currently assigned and, if
necessary, the computer/device name for each client will be listed for identification.
If the DHCP client is activated on the base station phone (IP address type =
Obtained automatically, page 87) this will be shown in the list with the name "telephony".
You can enter this name in the address field of the PC's Web browser instead of the IP
address if you want to establish a connection to the phone Web configurator (page 85).
Defining the router's name and domain
You can assign a name to your router. You can enter this name instead of the IP address
when you create a connection to the router's Web configurator:
http://Host Name.
If the router is located in a different network, you also have to enter the name of the
domain which contains the router: http://Host Name.Domain Name.
¤ Open the following Web page: Router Settings ¢ Administration ¢ Regional Options.
¤ Enter the name of your choice for your router in the Host Name field, and the name of
the domain in the Domain Name field.
¤ Click Set to apply the settings.
The router is rebooted and you are logged off. The Login Web page is displayed again after
the reboot.
Setting the Regional Options
You can select the time zone for your router's operation and determine whether the time
should be automatically applied from a time server on the Internet.
Version 2, 21.12.2006
¤ Open the following Web page: Router Settings ¢ Administration ¢ Regional Options.
¤ In the Country field select the country in which you operate your base station.
¤ Highlight the required option in the Use Time Server field.
¤ Enter the Internet address for the time server in the Time Server field.
¤ Click Set to apply the settings.
81
CE 450 IP R / IM-Ost english / A31008-M1817-R601_1-7619 / web_server.fm / 02.03.2007
Setting or changing a password
Setting or changing a password
The Web configurator for the router is secured with the password "0000" by default. To prevent unauthorised changes to the router configuration, you should change the password
from time to time.
¤ Open the following Web page: Router Settings ¢ Administration ¢ Remote Management.
¤ Enter a password in the Password field and repeat it in the Confirm new password field
(3 - 20 characters; case-sensitive).
¤ Click Set to apply the settings.
Please note:
If you have forgotten your router password, you will have to reset your Gigaset CE 460 IP R at the base
station (page 57). Please note that doing so will reset all settings on the base station phone and the
base station router to the default settings.
Setting the time until automatic log-off
Enter a period of time after which the Web configurator will automatically log-off if no
entry is made.
¤ Open the following Web page: Router Settings ¢ Administration ¢ Remote Management.
¤ Enter the period of time in seconds in the Idle Time before Log Off field.
¤ Click Set to apply the settings.
Configuring Remote Management for the router from external
networks
Remote management means that your router can be configured by a PC that is outside your
local network, all with the help of a standard Web browser. The default settings for your
router mean that it can only be configured from your local network.
¤ Open the following Web page: Router Settings ¢ Administration ¢ Remote Management.
¤ In the Remote Management field highlight the On option if you want to permit remote
management.
¤ If you want to restrict remote management to a particular PC, you should also enter the
IP address of this PC in the IP Address field. Entering 0.0.0.0 means that remote management from any PC is enabled.
Please note:
If you want to restrict remote management to one particular PC, you must ensure that the IP address
was not dynamically assigned to this PC.
¤ If you enter a port number in a Public Port field, access to remote management is only
possible via this port (default port = 80).
Version 2, 21.12.2006
¤ Click Set to apply the settings.
82
CE 450 IP R / IM-Ost english / A31008-M1817-R601_1-7619 / web_server.fm / 02.03.2007
Updating the router's firmware
Updating the router's firmware
Siemens always provides you with the latest version of the router firmware. This is available
on the Internet at: www.siemens.com/gigaset
To load the new firmware onto your router you must first download it from the Internet
onto your PC.
Then proceed as follows:
¤ Close down all activities on your local network.
¤ Open the following Web page: Router Settings ¢ Administration ¢ Load Firmware.
The version of the firmware currently being used on your router is displayed in the Current
Firmware Version line. You can only download firmware with a higher version number from
the PC to the router.
¤ In the Firmware Update File field, enter the path name of the file with the firmware you
have downloaded from the Internet. You can also use the Browse ... button to navigate
to the file.
¤ Click Load Firmware.
The firmware will now be updated.
Please note: You should not use the base station phone during the firmware update. In
particular, do not reset the base station!
Please note:
– Do not disconnect the base station from either the mains power supply or the local PC during the
updating procedure. Updating can take several (approx. 3) minutes.
– The base station is automatically restarted after a successful update. The registration page will be
displayed again after the restart.
– The base station phone's firmware is not updated during this firmware update. To update the
firmware update for the base station phone see page 58 or page 106.
Displaying the security log
The security log lists all disallowed attempts to access the network.
¤ Open the following Web page: Router Settings ¢ Administration ¢ Security Log.
¤ Click Refresh to update the display, or Clear to delete the log list.
Reboot
You can restart your router if it is not working properly. It should then be ready for use
again.
¤ Open the following Web page: Router Settings ¢ Administration ¢ Reboot.
¤ Click Reboot.
Version 2, 21.12.2006
Please note:
The reboot can take several minutes (depending on the provider). It can therefore take several minutes until you have a connection to the Internet again.
83
CE 450 IP R / IM-Ost english / A31008-M1817-R601_1-7619 / web_server.fm / 02.03.2007
Checking status information via the router
Checking status information via the router
General information about the router is displayed.
¤ In the menu list, click on the Status tab.
The following information is displayed:
Internet
Connection Type
Current connection type for the Internet connection. For settings, see page 71.
IP Address
Current router IP address for the connection to the Internet. For settings, see page 71.
Gateway
IP address for the gateway connecting your router to the Internet. For assigning, see
page 71.
DNS
Display of the preferred and alternative DNS server. For entering, see page 78.
Local Network
IP Address
Router's current IP address. For assigning, see page 80.
DHCP Server
Status of the DHCP server. For activating and deactivating the DHCP server, see page 80.
Firewall
Status of the firewall. For activating and deactivating, see page 74.
Device
Firmware Version
Version of the firmware currently downloaded to the router. You can download updates
of the firmware to the router (page 83). Firmware updates are available on the Internet.
WAN MAC Address
Public MAC address of the base station router.
Version 2, 21.12.2006
LAN MAC Address
Local MAC address of the base station router.
84
CE 450 IP R / IM-Ost english / A31008-M1817-R601_1-7619 / web_server.fm / 02.03.2007
Connecting the PC to the phone Web configurator
Phone Web configurator
You can make the following settings using the phone Web configurator:
u Connecting your base station phone to the local network (page 87)
u Configuring for the telephony
– Make VoIP provider settings (page 90)
– Configure VoIP accounts
– Activate/deactivate the Gigaset.net connection
– Make settings to improve voice quality for the VoIP connections
– Assign VoIP phone numbers to the individual handsets
u Setting for the automatic area code (page 103)
u Type of DTMF signalling (for remote operation of a network mailbox)
u Data server for downloading updates of phone firmware (page 106)
u Displaying VoIP status messages on your handset (page 107)
Connecting the PC to the phone Web configurator
Precondition: The settings of an available PC firewall allow the PC and base station to communicate with each other.
¤ Launch the Web browser on your PC.
¤ In the Web browser address field, enter the IP address of the base station phone,for
¤
example
http://192.168.1.150, or http://telephony.gigaset.
You can check the phone's current IP address on the handset (page 60).
If you have activated the dynamic allocation of IP addresses (DHCP) on the router
(page 80) and on the phone (page 87), your phone's IP address can change each time
the router is rebooted.
Press the return key.
Version 2, 21.12.2006
A connection is established to the Web configurator for the base station phone or the base
station router.
85
CE 450 IP R / IM-Ost english / A31008-M1817-R601_1-7619 / web_server.fm / 02.03.2007
Logging in, setting the Web configurator language
Logging in, setting the Web configurator language
Once you have successfully established the connection, the Login Web page will be
displayed in the Web browser.
You can select the language you want the menus and Web configurator dialogues to be
displayed in. The language that is currently selected is displayed in the top field of the Web
page.
¤ If necessary, click to open the list of available languages.
¤ Select the language.
¤ In the bottom field of the Web page, enter your router's or phone's system PIN (default
setting: 0000) to access the Web configurator functions.
¤ Click OK.
Once you have successfully logged in, a Home opens with general information on the Web
configurator.
Please note:
– If you have forgotten your system PIN, you will have to reset your base station to the factory settings. Please note that this will restore all other settings too (page 57).
– If you do not make any entries for a lengthy period (around 10 minutes), you will be automatically
logged off. The next time you try to make an entry or open a Web page, the Login Web page will
be displayed. Enter the system PIN again to log in again.
– Entries that had not yet been saved in the router or on the phone before automatic log-off are lost.
Menu bar
Version 2, 21.12.2006
The following menus are available in the phone Web configurator:
u Home
The start screen is opened once you have registered with the Web configurator. It contains information on the Web configurator menus.
u Settings (page 85)
This menu allows you to make settings on your phone.
u Status (page 108)
This menu gives you information about your phone.
u Router-Settings
You can use this menu to start the router Web configurator (page 69), to make settings
on the base station router.
86
CE 450 IP R / IM-Ost english / A31008-M1817-R601_1-7619 / web_server.fm / 02.03.2007
IP Configuration
IP Configuration
Make the necessary settings for operating your phone in your local network and to connect
it to the Internet. For more detailed explanations of the individual components/terms, see
the glossary (page 135).
The base station phone and router are set by default so that there is a connection between
them. You only have to change the IP configuration for your phone in exceptional circumstances, e.g. if you have configured port forwarding to the phone for the router, or if you
had to deactivate the router's DHCP server. In this case you need to assign the phone a fixed
IP address.
Assigning the IP address
¤ Open the following Web page: Settings ¢ IP Configuration.
¤ In the Address Assignment area, select the IP address type.
Select Obtained automatically if you want your phone to be assigned a dynamic IP address by
a DHCP server in your local network. No further settings are necessary for the local network.
Select Static if you would like to set up a static IP address for your phone. A fixed IP address
makes sense, for example, if port forwarding is set up on the router for the phone
(page 76).
The following fields are displayed when you select IP address type = Static:
IP address
Enter an IP address for your phone. This IP address allows it to be reached by other subscribers in your local network (e.g. PC).
The default is 192.168.1.2.
Please note the following:
– The IP address must be from the address block for private use that is used in the
router. This is generally in the range 192.168.0.1 – 192.168.255.253 with Subnet
mask 255.255.255.0. The subnet mask determines that the first three parts of the IP
address must be identical for routers and all subscribers in your LAN.
– The static IP address must not belong to the address block (IP pool range) that is
reserved for the DHCP server of the base station router. It must also not be being used
by another device that is connected to the base station via the LAN connection
(directly or via a hub/switch).
If necessary, check the setting at the base station router (page 80).
Version 2, 21.12.2006
Subnet mask
Enter the subnet mask that you have set at your base station router (page 80).
Default gateway
Enter the private IP address for the base station router (page 80). Your base station
phone requires this information to be able to access the Internet.
The default is 192.168.1.1.
87
CE 450 IP R / IM-Ost english / A31008-M1817-R601_1-7619 / web_server.fm / 02.03.2007
IP Configuration
Preferred DNS server
Enter the IP address for the preferred DNS server.
You can enter the private IP address for the base station router here. The router forwards
base station phone address requests to its DNS server (page 78).
The default is 192.168.1.1.
Alternate DNS server (optional)
Enter the IP address for the alternative DNS server that should be used in situations
where the preferred DNS server cannot be reached.
You can also enter the private IP address for the base station router here.
Click on Set to save the changes.
Click on Cancel to reject the changes.
Allowing access from other networks
The default setting for your phone is set such that you can only access your phone's
Web configurator via a PC that is in the same local network as your phone. The subnet mask
of the PC must match that of the phone.
You can also allow access from PCs in other networks.
Warning:
Expansion of access entitlement to other networks increases the risk of unauthorised access. It is
therefore recommended to deactivate remote access again if you no longer need it.
¤ Open the following Web page: Settings ¢ IP Configuration.
¤ In the Remote Management area, activate the Yes option to permit access from other net-
Version 2, 21.12.2006
works.
To deactivate remote access, click on the No option. Access is then limited to PCs in your
own local network.
Access to the phone Web configurator from other networks is only possible if your base station router is set accordingly. The base station router must pass on the service requests
from "outside" to port 80 (default port) of the phone (page 76).
To establish a connection, the public IP address or the DNS name of the base station router
and, where applicable, the port number on the base station (page 78) router must be indicated in the Web browser of the remote PC.
88
CE 450 IP R / IM-Ost english / A31008-M1817-R601_1-7619 / web_server.fm / 02.03.2007
Configuring telephone connections
Configuring telephone connections
You can configure up to six VoIP phone numbers on your phone. You need to set up a VoIP
account with a VoIP provider for each VoIP phone number. You must save the access data
for each account and for the relevant VoIP provider in the phone. You can assign a name to
every connection.
To configure the connections:
¤ Open the following Web page: Settings ¢ Telephony ¢ Connections.
A list (see Figure 3) will be shown with all possible connections that you can configure, or
have already configured, for your phone.
Version 2, 21.12.2006
Figure 3 List of possible connections
The list will show the following:
Name
Name of the connection. The name that you have defined for the connection is displayed (page 90) or the default name (IP1 to IP6). This name is shown, for example, on
the display if a call is received for this phone number (page 29).
Status
The status of the connection will be shown for VoIP connections:
registered
The connection is activated. The phone has been successfully registered. You can use
the connection to make calls.
Disabled
The connection is deactivated. The phone is not registering with the corresponding
account with the VoIP service. You cannot use the connection to make or receive calls.
Registration failed / Server not accessible (examples)
The phone could not be registered with the VoIP service, e.g. because the VoIP access
data is incomplete or incorrect, or because the phone is not connected to the Internet.
There is information about this in the section "Questions and answers" from page 113
onwards.
89
CE 450 IP R / IM-Ost english / A31008-M1817-R601_1-7619 / web_server.fm / 02.03.2007
Configuring telephone connections
Active
You can use the option in the Active column to activate ( ) and deactivate ( ) VoIP
connections. If a connection is deactivated, the phone will not register for this connection with the VoIP service. Your phone cannot be reached via this VoIP phone number.
The connection can be activated/deactivated by clicking directly on the option. The
change does not need to be saved.
To configure a connection or to change the configuration of a connection:
¤ Click on the Edit button next to the connection.
This will open a Web page where you can make the settings needed. For more information
see section "Configuring the VoIP connection" on page 90.
Configuring the VoIP connection
Open the Web page:
¤ Open the following Web page: Settings ¢ Telephony ¢ Connections.
¤ Click on the Edit button next to the VoIP connection that you want to configure or whose
configuration you want to change.
This will open a Web page where you can make the settings that your phone needs to
access your provider's VoIP server.
The Web page always displays the following areas:
u IP Connection (page 90),
u Personal Provider Data (page 91) and
u Call Forwarding (page 92)
The areas
u General Provider Data (page 92) and
u Network (page 93)
can be shown and hidden by clicking the Show Advanced Settings and Hide Advanced Settings
buttons.
You must enter the VoIP provider's general access data in these areas. You can download
the general access data for many VoIP providers from the Internet (page 96).
¤ Make the settings on the Web page.
¤ Save them in the phone, see page 95.
¤ Activate the connection if necessary, see page 95.
Area: IP Connection
Version 2, 21.12.2006
Connection Name or Number
Enter a name for the VoIP connection or the VoIP phone number (max. 16 characters).
The connection will be shown under this name on the handset and in the Web configurator interface, e.g. when assigning sending and receiving numbers (page 100), with
call display (page 29).
90
CE 450 IP R / IM-Ost english / A31008-M1817-R601_1-7619 / web_server.fm / 02.03.2007
Configuring telephone connections
Provider
The name of your VoIP provider will be shown if you have already selected it.
Click the Select VoIP Provider button to select your provider and to start downloading the
general data for the VoIP provider from the Internet if required. To find out how to do
this, please read "Selecting the VoIP provider and downloading the VoIP provider data"
on page 96.
Please note:
– If you click on the Select VoIP Provider button, any changes that have been made to the Web page
will be saved and checked. Values may need to be corrected before the Select VoIP Provider operation is started.
– The downloaded VoIP provider data will be entered in the General Provider Data (page 92) and
Network (page 93) areas, so that, generally speaking, no further settings need to be made in these
areas.
If the general data for your VoIP provider is not available for download, you will need to make
these settings yourself as described below.
Area: Personal Provider Data
Version 2, 21.12.2006
Enter the configuration data that is necessary for accessing your VoIP provider's SIP service.
You will receive this data from the VoIP provider.
Authentication Name
Specify the registration or authentication ID agreed with your VoIP provider. The registration ID serves as the access ID that your phone must specify when registering with
the SIP proxy/registrar server. The Authentication Name is mainly identical to the Username,
i.e. to your Internet phone number.
Authentication password
Enter the password that you have agreed with your VoIP provider in the Authentication
password field. The phone needs the password when registering with the SIP proxy/registrar server.
Username
Enter the caller ID for your VoIP provider account. This ID is usually identical to the first
part of your SIP address (URI, your Internet phone number).
Example: If your SIP address is "987654321@provider.com", enter "987654321" in
Username.
Display name (optional)
Enter any name that should be shown in the other caller's display when you call them
via the Internet (example: Anna Sand). All characters in the UTF8 character set
(Unicode) are permitted. The name must not exceed 32 characters.
If you do not enter a name, your Username VoIP phone number will be displayed.
Ask your VoIP provider if this feature is supported.
91
CE 450 IP R / IM-Ost english / A31008-M1817-R601_1-7619 / web_server.fm / 02.03.2007
Configuring telephone connections
Area: Call Forwarding
You can also forward calls for this VoIP number to another external number (VoIP, fixed
network or mobile phone). The forwarding is done via VoIP.
The Call Forwarding area is where you define whether and when calls for this VoIP number
should be forwarded to another number.
You can also use the handset to set the forwarding and activate/deactivate it, see page 38.
Status
Use the On / Off option to activate or deactivate the call forwarding.
When
Choose when an incoming call should be forwarded: When busy / No reply / Always.
Call number
Enter the phone number to which the calls should be forwarded. Please note that you
may have to enter the area code when forwarding to a fixed network number in the
same area (depending on your VoIP provider and the setting for the automatic area
code, page 103).
The settings only affect the selected VoIP phone number.
Area: General Provider Data
Version 2, 21.12.2006
If you have downloaded the general settings for the VoIP provider from the Siemens configuration server (page 96), then the fields in this area will be preset with the data from the
download. Generally speaking, you will not need to make any settings in this area.
Domain
Specify the last part of your SIP address (URI) here.
Example: For the SIP address "987654321@provider.com", enter "provider.com" in
Domain.
Proxy server address
The SIP proxy is your VoIP provider's gateway server. Enter the IP address or the (fullyqualified) DNS name of your SIP proxy server. Example: myprovider.com.
Proxy server port
Enter the number of the communication port that the SIP proxy uses to send and receive
signalling data (SIP port).
Port 5060 is used by most VoIP providers.
Registrar server
Enter the (fully-qualified) DNS name or the IP address of the registrar server.
The registrar is needed when the phone is registered. It assigns the public IP address/
port number to your SIP address (Username@Domain) that was used by the phone at registration. With most VoIP providers, the registrar server is identical to the SIP server.
Example: reg.myprovider.com.
Registrar server port
Enter the communication port used in the registrar. It is mainly port 5060 that is used.
92
CE 450 IP R / IM-Ost english / A31008-M1817-R601_1-7619 / web_server.fm / 02.03.2007
Configuring telephone connections
Registration refresh time
Enter the time intervals at which the phone should repeat the registration with the VoIP
server (SIP proxy) (a request will be sent to establish a session). The repeat is required
so that the entry of the phone in the tables of the SIP proxy is retained and the phone
can therefore be reached. The repeat will be carried out for all activated VoIP phone
numbers.
The default is 180 seconds.
If you enter 0 seconds, the registration will not be repeated periodically.
Area: Network
Please note:
If you have downloaded the general settings for your VoIP provider from the Siemens configuration
server (page 96), some fields in this area will be preset with the data from this download (e.g. the
settings for the STUN server and the outbound proxy).
If NAT (Network Address Translation) and/or the firewall are activated on your base station
router, you may have to make some settings in this area so that your base station phone
can be reached (i.e. can be addressed) from the Internet.
Through NAT, the IP addresses of subscribers in the LAN are concealed behind the public IP
address of the router.
For incoming calls
If on the router port forwarding for SIP and RTP port (page 76) is activated to the phone,
no special settings are required for incoming calls.
If this is not the case, an entry in the NAT routing table (in the router) is necessary in order
for the phone to be reached. This is automatically created when the phone is registered
with the SIP service. In the interest of security, this entry is deleted at certain intervals
(session timeout). The phone must therefore confirm its registration at certain intervals
(see NAT refresh time, page 94), so that the entry stays in the routing table.
Version 2, 21.12.2006
For outgoing calls
The phone requires its public IP address so that it can receive the voice data for the other
caller and you can hear the other caller. If NAT is activated, the phone does not know the
public IP address.
If the NAT for your router (symmetric NAT) is the only NAT between the phone and the SIP
server, setting a value between 5056 and 5071 for your phone's SIP port will be enough
(page 102). The phone's STUN server must be deactivated. Set STUN enabled to No (see
below).
If the NAT for the router is not the only one between the phone and the SIP server (e.g. if
your router is connected to the Internet via another LAN and the router for this LAN has an
asymmetric NAT), there are two options:
u Your VoIP provider makes an outbound proxy available: the phone directs its request to
establish a connection to the outbound proxy (instead of to the SIP proxy). This provides
the data packet with the public IP address.
93
CE 450 IP R / IM-Ost english / A31008-M1817-R601_1-7619 / web_server.fm / 02.03.2007
Configuring telephone connections
Version 2, 21.12.2006
u The phone requests the public IP address from a STUN server on the Internet (Simple
Traversal of UDP over NAT). The phone's STUN server must be deactivated.
Set STUN enabled to Yes (see below).
STUN may not be enough, however, with your router's symmetric NAT. You may have to
forward an additional SIP and RTP port to the phone (Port Forwarding to all routers
involved, see page 76) and set a value outside the 5056 – 5071 range for the phone's
local SIP port (page 102).
The STUN server and outbound proxy are used alternately to work around the NAT/firewall
in the router.
STUN enabled
Click Yes if you want your phone to use STUN.
STUN server
Enter the (fully-qualified) DNS name or the IP address of the STUN server on the
Internet.
If you selected the Yes option in the STUN enabled field, you must enter a STUN server
here.
STUN port
Enter the number of the communication port on the STUN server. The default port
is 3478.
STUN refresh time
Enter the time intervals at which the phone should repeat the registration with the
STUN server. The repeat is required so that the entry of the phone in the tables of the
STUN server is retained. The repeat will be carried out for all activated VoIP phone numbers.
Ask your VoIP provider for the STUN refresh time.
The default is 240 seconds.
If you enter 0 seconds, the registration will not be repeated periodically.
NAT refresh time
Specify the intervals at which you want the phone to update its entry in the NAT routing
table. Specify an interval in seconds that is a little smaller than the NAT session timeout.
As a rule you should not change the preconfigured value for the NAT refresh time.
Outbound proxy mode
Specify when the outbound proxy should be used.
Always
All signalling and voice data sent by the phone is sent to the outbound proxy.
Auto
Data sent by the phone is only sent to the outbound proxy when the phone is connected
to a router with symmetric NAT or blocking firewall. If the phone is behind an asymmetric NAT, the STUN server is used.
If you have set STUN enabled = No or have not entered a STUN server, the outbound proxy
is always used.
Never
The outbound proxy is not used.
If you do not make an entry in the Outbound proxy field, the phone behaves independently of the selected mode, as with Never.
94
CE 450 IP R / IM-Ost english / A31008-M1817-R601_1-7619 / web_server.fm / 02.03.2007
Configuring telephone connections
Outbound proxy
Enter the (fully qualified) DNS name or the IP address of your provider's outbound proxy.
Please note:
With many providers, the outbound proxy is identical to the SIP proxy.
Outbound proxy port
Enter the number of the communication port used by the outbound proxy.
The default port is 5060.
Saving settings on the phone
¤ Click Set to save the changes.
The Connections list will be shown after saving (see Figure 3 on page 89).
If you want to reject the changes that have been made, click Cancel. The Web page is reloaded with the data saved on the phone.
Please note: If you do not make any entries for a lengthy period, the connection to the Web
configurator is automatically terminated. Unsaved entries are lost. If necessary, implement
temporary security measures. You can subsequently continue the entry and make changes
if necessary.
Activating a new connection
If you have configured a new VoIP connection, you must also activate it.
In the Connections list:
¤ Activate the relevant option in the Active column ( = activated).
Your phone will register itself with the VoIP provider using the relevant access data. If the
registration is successful, after a short period the Status column will show registered for the
connection. You can now be reached on this VoIP phone number.
Please note:
Version 2, 21.12.2006
Once the new entry has been made, the VoIP phone number for each handset is assigned as a receiving number. For how to adjust the assignment, see page 100.
95
CE 450 IP R / IM-Ost english / A31008-M1817-R601_1-7619 / web_server.fm / 02.03.2007
Configuring telephone connections
Selecting the VoIP provider and downloading the VoIP provider data
Profile files with the general access data for the most important VoIP providers are available
for download on the Siemens server on the Internet. The IP address for the server is stored
in your phone (page 106).
Navigation:
¤ Open the following Web page: Settings ¢ Telephony ¢ Connections.
¤ Click the Edit button next to the VoIP connection for which you wish to download the
provider data.
¤ In the IP Connection area, click the Select VoIP Provider button.
This will display information on the download procedure.
The phone establishes a connection with the Siemens server on the Internet. The download procedure has several steps:
¤ Click Next.
¤ From the list, select the country for which the list of VoIP providers is to be loaded.
¤ Click Next.
¤ Select a VoIP provider from the list. If your provider is not included in the list, select Other
Provider. You will then have to enter all the VoIP data manually (page 90).
¤ Click Finish.
The data for the provider selected will be loaded onto your phone.
Activating/deactivating the Gigaset.net connection
Your phone is assigned a Gigaset.net phone number on delivery. As soon as you have connected your phone to the Internet, you can make calls using the Gigaset.net and receive
calls from other Gigaset.net subscribers, provided that your Gigaset.net connection has
been activated. You can deactivate the Gigaset.net connection.
¤ Open the following Web page: Settings ¢ Telephony ¢ Connections. The list of connections will be displayed (see Figure 3 on page 89).
¤ In the Gigaset Net area: use the option in the Active column to activate ( ) or deactivate
( ) the Gigaset.net connection.
Please note:
Version 2, 21.12.2006
If you do not use your Gigaset.net connection for six weeks, it is automatically deactivated. You cannot be reached for calls from the Gigaset.net.
The connection is reactivated:
– as soon as you start a search in the Gigaset.net directory (page 34) or
– make a call via the Gigaset.net (dial a number with #9 at the end) or
– activate the connection via the Web configurator as described above.
96
CE 450 IP R / IM-Ost english / A31008-M1817-R601_1-7619 / web_server.fm / 02.03.2007
Optimising voice quality for VoIP connections
Optimising voice quality for VoIP connections
You can make general and connection-specific settings to improve the voice quality for
VoIP telephony.
¤ Open the following Web page: Settings ¢ Telephony ¢ Audio.
The voice quality for VoIP connections is mainly determined by the voice codec used for
transferring the data and the available bandwidth of your DSL connection.
In the case of the voice codec, the voice data is digitalised (coded / decoded) and compressed. A "better" codec (better voice quality) means more data needs to be transferred,
i.e. perfect voice data transfer requires a DSL connection with a larger bandwidth.
The following voice codecs are supported by your phone:
G711 a law / G711 µ law
Excellent voice quality (comparable with ISDN). The necessary bandwidth is 64 kbit/s
per voice connection.
G726
Good voice quality (inferior to that with G711 but better than with G729).
Your phone supports G726 with a transmission rate of 32 kbit/s per voice connection.
G729
Average voice quality. The necessary bandwidth is less than 8 kbit/s per voice connection.
Both sides of a phone connection (caller/sender side and receiver side) must use the same
voice codec. The voice codec is negotiated between the sender and the recipient when
establishing a connection.
You can influence the voice quality by selecting (bearing in mind the bandwidth of your
DSL connection) the voice codecs your phone is to use, and specifying the order in which
the codecs are to be suggested when a VoIP connection is established.
Area: Settings for Bandwidth
Version 2, 21.12.2006
The settings in this area influence all VoIP connections (VoIP phone numbers).
Allow 1 VoIP call only
Generally speaking you can make two VoIP calls at the same time on your phone. If,
however, your DSL connection has a narrow bandwidth, there may be problems if two
VoIP calls are made at the same time. The data is no longer transferred properly (long
voice delay, data losses etc.).
¤ Activate the Yes option next to Allow 1 VoIP call only to prevent any further parallel VoIP
phone connections being established.
¤ If you wish to permit two VoIP connections, activate the No option.
Please note: If only one VoIP connection is permitted, the following VoIP network services are no
longer available:
– Call waiting
Call waiting is not displayed during a call via VoIP.
– External consultation call from a VoIP call
– Toggling and initiating a conference call via VoIP
97
CE 450 IP R / IM-Ost english / A31008-M1817-R601_1-7619 / web_server.fm / 02.03.2007
Optimising voice quality for VoIP connections
Voice Quality
Default settings for the codecs used are stored in your phone: one setting optimised for
narrow bandwidths and one setting optimised for wide bandwidths.
¤ Activate one of the options Optimized for low bandwidth / Optimized for high bandwidth if
you wish to accept a default setting for all VoIP connections. The settings are shown
in the Settings for Connections area and cannot be changed.
¤ Activate the Own Codec preference option if you wish to select and set connectionspecific voice codecs yourself (see section "Area: Settings for Connections").
Version 2, 21.12.2006
Area: Settings for Connections
In this area you can make specific settings for each of your VoIP phone numbers.
You can make the following settings for each VoIP phone number configured on your
phone:
Volume for VoIP Calls
Depending on the VoIP provider, it is possible that the received voice/earpiece volume is
too low or too high, so that adjusting the volume via the handset is not adequate.
Specify whether the received volume range is too high or too low. The following options
are available:
Low
Voice/earpiece volume is too high. Activate this option to reduce the volume by 6 dB.
Normal
The voice/earpiece volume does not need to be raised/lowered.
High
Voice/earpiece volume is too low. Activate this option to reduce the volume by 6 dB.
Voice codecs
Precondition: The Own Codec preference option is activated for the Voice Quality in the
Settings for Bandwidth area.
Select the voice codecs your phone is to use, and specify the order in which the codecs
are to be suggested when a VoIP connection is established via this VoIP phone number.
¤ Apply the voice codecs that your phone is to suggest with outgoing calls into the
Selected codecs list.
To do this, in the Available codecs list click on the voice codec that you want to apply
(you can mark several entries using the Shift key or the Ctrl key). Click on the <Add
button.
¤ Move the voice codecs that you do not want the phone to use into the Available codecs
list.
Also, select the voice codecs in the Selected codecs list (see above) and click on the
Remove> button.
¤ Sort the voice codecs in the Selected codecs list into the order in which they should be
suggested to the receiving device when a connection is established. To do this, use
the Up and Down buttons.
When establishing a VoIP connection, the phone suggests the 1st voice codec in the
Selected codecs list to the receiving device to begin with. If the receiving device does not
accept this voice codec (e.g. because it is not supported), the 2nd voice codec in the list
is suggested and so on.
98
CE 450 IP R / IM-Ost english / A31008-M1817-R601_1-7619 / web_server.fm / 02.03.2007
Optimising voice quality for VoIP connections
If the receiving device does not accept any of the voice codecs in the Selected codecs list,
the connection is not established. An appropriate message will be displayed on the
handset.
Please note:
– You should only deactivate codecs (put them in the Available codecs list) if there is a particular
reason. The more codecs that are deactivated, the greater the danger that calls will not be able to
be established due to unsuccessful codec negotiations.
– With incoming calls, all supported voice codecs are always permitted.
Area: Settings for Codecs
To save additional bandwidth and transmission capacity, on VoIP connections that use
codec G729 you can suppress the transmission of voice packets in pauses ("Silence
Suppression"). Then, instead of the background noises in your environment, your caller
hears a synthetic noise generated in the receiver.
Please note: "Silence Suppression" can sometimes lead to deterioration in the voice
quality.
¤ In the Enable Annex B for codec G729 field, state whether, when using codec G729, transmission of data packets for pauses is to be suppressed (activate the Yes option).
Saving settings on the phone
¤ Click on the Set button to save the settings for the voice quality.
Please note:
You should observe the following for good voice quality:
– Configure the Quality of Service for your router as described on page 78.
– When making calls using VoIP, avoid performing other Internet activities (e.g. surfing the net).
– Irrespective of the codec used and the network capacity utilisation, please note that voice delays
can occur. Therefore, allow your VoIP calling partner to finish speaking. Do not interrupt him or
her.
Voice quality and infrastructure
Version 2, 21.12.2006
With your Gigaset CE 460 IP R you have the opportunity to make calls with good voice
quality via VoIP.
In addition to the phone settings, your phone's performance with VoIP - and therefore the
voice quality - also depends on the characteristics of the infrastructure as a whole.
The performance is influenced by the QoS of your base station router (page 78) and, if
necessary, other applications that also use the DSL connection. These may include the
following components from your VoIP provider:
u DSLAM
u DSL transmission line and speed
u Connection paths over the Internet
In VoIP networks, voice quality is affected by various things including the "quality of
service" (QoS). If the entire infrastructure demonstrates QoS, voice quality is better (fewer
delays, less echoing, less crackling etc.).
99
CE 450 IP R / IM-Ost english / A31008-M1817-R601_1-7619 / web_server.fm / 02.03.2007
Assigning sending and receiving numbers to handsets
Assigning sending and receiving numbers to handsets
You can assign up to six VoIP phone numbers to your phone.
You can assign these numbers to the individual handsets that are registered to your base
station as receiving and sending numbers. This means for each handset, you define the
calls that it will ring for, and which VoIP account (sending number) is to be used by your
VoIP provider to calculate outgoing VoIP calls.
Please note:
A handset is assigned the following numbers after it is registered on the base station:
– Receiving numbers: all phone numbers for the phone.
– Sending numbers: the phone number that you entered at the start of the phone configuration.
Your Gigaset.net number is permanently assigned to each handset as the sending and receiving
number.
¤ Open the following Web page: Settings ¢ Telephony ¢ Number Assignment.
This will display the names of all registered handsets, and a list for each handset with the
phone numbers that are configured and activated for the phone. The connection names
are shown in the Connections column.
¤ Define a VoIP phone number as the sending number for each handset. To do this, click
on the option following the phone number in the Send column. The previous assignment will automatically be deactivated.
¤ Select the phone numbers for each handset that are to be assigned to the handset as
receiving numbers. To do this, click on the option following the phone number in the
Receive column. Every handset can be assigned several phone numbers or no phone
number ( = assigned).
¤ Now click Set to save your settings.
Please note:
Version 2, 21.12.2006
– If a VoIP phone number that has been assigned to a handset as a sending number is deleted/deactivated, then the handset will automatically be assigned the first VoIP phone number.
– If a phone number is not assigned to any handset as a receiving number, calls to this number will
be signalled on all handsets.
– If you have not assigned receiving numbers to any of the handsets, calls to all connections will be
signalled on all handsets.
100
CE 450 IP R / IM-Ost english / A31008-M1817-R601_1-7619 / web_server.fm / 02.03.2007
Setting DTMF signalling for VoIP
Setting DTMF signalling for VoIP
DTMF signalling, for example, is required to check and control some network mailboxes via
digit codes.
¤ Open the following Web page: Settings ¢ Telephony ¢ Advanced Settings.
Make the desired settings for the DTMF signals in the DTMF over VoIP Connections area.
Specify how key codes are to be converted and sent as DTMF signals: as audible information in the voice channel or as a "SIP Info" message.
Ask your VoIP providers which type of DTMF transmission they support.
¤ Activate Audio or RFC 2833 if DTMF signals are to be transmitted acoustically (in voice
packets).
¤ Activate SIP Info if DTMF signals are to be transmitted as code.
Please note:
The settings for DTMF signalling apply to all VoIP connections (VoIP accounts).
Version 2, 21.12.2006
¤ Now click Set to save your settings.
101
CE 450 IP R / IM-Ost english / A31008-M1817-R601_1-7619 / web_server.fm / 02.03.2007
Defining local communication ports for VoIP
Defining local communication ports for VoIP
¤ Open the following Web page: Settings ¢ Telephony ¢ Advanced Settings.
In the Listen Ports for VoIP Connections area, specify which local ports the telephone is to use
for VoIP telephony. The ports must not be used by any other subscriber in the LAN.
SIP port
Specify the local communication port that the phone should use to send and receive signalling data. Specify a number between 1024 and 49152.
The default port number for SIP signalling is 5060.
The recommended value is between 5056 and 5071.
RTP port
Specify the local communication port that the phone should use to send and receive
voice data. Enter an even number between 1024 and 49152. The port number must
not match the port number in the SIP port field. If you enter an odd number, the even
number just below it will be set (e.g. if you enter 5003, 5002 is set).
The default port number for SIP signalling is 5004.
Use random ports
Click the Yes option if you do not want the phone to use fixed ports for SIP port and RTP
port, but rather to use any free ports.
The use of random ports makes sense if you want several phones to be operated on the
base station router. The phones must then use different ports so that the router's NAT
is only able to forward incoming calls and voice data to one (the intended) phone.
If you click No, the phone will use the ports specified in SIP port and RTP port.
Version 2, 21.12.2006
¤ Now click Set to save your settings.
102
CE 450 IP R / IM-Ost english / A31008-M1817-R601_1-7619 / web_server.fm / 02.03.2007
Setting Area Code Predialling
Setting Area Code Predialling
In VoIP calls you must generally always dial the area code – even for local calls.
You can save the annoying need to dial the area code for local calls by activating the Area
Code Predialling function. In VoIP calls, the area code entered is then prefixed to all numbers
that do not start with 0 – even when dialling numbers from the directory and other lists.
¤ Open the following Web page: Settings ¢ Telephony ¢ Dialing Plans.
¤ Enter your area code in the Area Code field, e.g. 020.
¤ Click the Yes option next to Predial area code for local calls through VoIP to activate the
¤
function.
If you click No you must enter the area code even for local calls via VoIP. Numbers in the
directory must always contain the area code for dialling via VoIP.
Click Set to save the settings.
Please note that if the option is activated, the area code is prefixed to all phone numbers that do not
start with 0. This applies particularly for the number for the network mailbox (page 47).
Loading and deleting directories to/from the PC.
The Web configurator has the following options for editing the directories of the registered
handsets.
u Store the handset directories on a PC. They will be stored in tsv-ASCII files (tsv = tabulator separated values). These files can be edited with an ASCII editor (e.g. Notepad/Editor
in Windows accessories) and loaded onto every handset that is registered. You can also
transfer directory entries from the tsv file into your Outlook™ address book.
u Transfer Outlook™ contacts to the handset directories. Export Outlook™ contacts into a
tsv-ASCII file and transfer this into the directories. Find out how to do this in the section
"Format of the directory file (tsv file)" on page 105.
u Delete the directory on the handset. If you have edited the directory file (tsv file) on the
PC and would like to use this modified directory on the handset, you can delete the
current directory from the handset first.
Tip: Back up the current directory on your PC before deleting it. You can then load it back
onto the handset if the modified directory is affected by formatting errors and some, or
all, of it cannot be loaded onto the handset.
Preconditions:
u The handset can send and receive directory entries.
u The directory on the handset is not being accessed, i.e. the directory is not open.
¤ Open the following Web page: Settings ¢ Telephony ¢ Directory.
¤ In the Handset area, select the handset whose directory you want to edit. To do this, click
Version 2, 21.12.2006
on the option before the handset.
103
CE 450 IP R / IM-Ost english / A31008-M1817-R601_1-7619 / web_server.fm / 02.03.2007
Loading and deleting directories to/from the PC.
Loading the directory file from the PC to the handset
¤ In the Transfer directory to handset field: enter the tsv file (complete path name) that is to
be loaded onto the handset. Click the Browse button to navigate to the file.
¤ Click the Transfer button to start the transfer.
The display will show how many of the entries from the tsv file are being transferred to the
directory. If a formatting error occurs, the line number for the affected entry will be specified.
Transfer rules
The directory entries from a tsv file that are loaded onto the handset will be added to the
directory. No directory entries will be overwritten or deleted.
If the phone number for a directory entry is identical to the phone number for an entry in
the tsv file, the entry is not copied to the handset.
Loading the directory from the handset to the PC
¤ In the Handset Directory area, click on the Save button. A Windows dialogue will be shown
to save the file.
¤ Enter the directory on the PC (complete path name) in which the directory file is to be
stored. Click on the Save button or OK.
Deleting the directory
¤ In the Handset Directory area, click on the Delete button.
¤ Confirm the security prompt Telephone directory of the selected handset will be deleted. Con-
tinue? with OK.
All directory entries will be deleted.
Please note:
Version 2, 21.12.2006
For how to delete the directory on the handset, see page 41.
104
CE 450 IP R / IM-Ost english / A31008-M1817-R601_1-7619 / web_server.fm / 02.03.2007
Loading and deleting directories to/from the PC.
Format of the directory file (tsv file)
The following describes the structure of the tsv file as it is created from the phone. The
phone expects the same structure if you load a tsv file from the PC onto a handset. A tsv
file created by Outlook™ may need editing with an ASCII editor before it can be loaded onto
a handset.
Every directory entry in the tsv file is recorded in one line (which is closed with an end-ofline symbol).
The data in each entry has specific positions within the line. The positions are separated by
tabs (<tab>). The following data is written in the file in the specified order:
1. Internal code (can remain empty)
2. Name
3. Number
If one of the above parameters in a directory entry is not set, then the relevant position
must remain empty (<tab><tab>).
In the case of directory entries for the Gigaset C46 handset, five tabs <tab> must be
inserted between the number and the end-of-line symbol. These spaces are reserved for
additional information, which can be stored in the directory for other Gigaset handsets
(e.g. the Gigaset S45).
Example:
You want to create an entry for Anna Sand with the number 123456.
The tsv file must contain the following in a line:
Version 2, 21.12.2006
<tab>Anna Sand<tab>123456<tab><tab><tab><tab> <tab><enter>
105
CE 450 IP R / IM-Ost english / A31008-M1817-R601_1-7619 / web_server.fm / 02.03.2007
Defining the server for firmware updates, starting the update
Defining the server for firmware updates, starting the update
If necessary you can download updates for the phone firmware to your base station. You
can either download the updates directly from the Internet or from a PC in your local network.
Using the Web configurator you can specify from where the firmware should be loaded.
¤ Open the following Web page: Settings ¢ Miscellaneous.
Please note:
The base station router's firmware is not updated during this firmware update. For the firmware
update for the base station router see page 83.
Downloading the firmware update directly from the Internet
The server on which Siemens makes new firmware versions available for your base station
is set by default. The URL of the Internet server is displayed in the Data server field.
The firmware is loaded from the Internet if you do not enter a local file in the User defined
firmware file field before this update.
Please note:
– When updating from the Internet, checks are made to ensure that no newer version of the
firmware exists. If this is not the case, the operation is terminated.
– You should not change the URL for the Internet server because this address is also used to load
provider information from the Internet. If you have entered another URL, you can re-activate the
default URL by restoring the base station default settings (page 57).
Conducting the firmware update locally
Precondition: A Web server is running on the local PC (e.g. Apache).
¤ First, load the desired version of the firmware from the Internet onto a local PC. Store
the firmware file in the Web server's file directory.
¤ In the User defined firmware file field enter the IP address of the PC in your local network
and the complete path and name of the firmware file within the Web server directory.
Example: 192.168.2.105/S450IP/Firmware_File.bin.
¤ Click Set to save the changes.
This setting is automatically used for the subsequent firmware update. The Internet server
URL stays saved and is re-used for further firmware updates. If you want to use a local PC
again for another update, then you have to re-enter the IP address and file name.
Please note:
Version 2, 21.12.2006
If an error arises during a firmware update from a local PC, the most recent version of the firmware is
automatically downloaded from the Internet.
106
CE 450 IP R / IM-Ost english / A31008-M1817-R601_1-7619 / web_server.fm / 02.03.2007
Activating/deactivating the automatic version check
Starting a firmware update
Preconditions:
u No calls are being made using your base station.
u There is no internal connection between the registered handsets.
u The base station menu is not open in any of the handsets.
¤ Click Update Firmware.
The firmware is updated. This process can take up to 3 minutes.
Please note:
You can also start the firmware update on the handset (page 58).
Activating/deactivating the automatic version check
When the version check is activated, the phone checks on a daily basis whether the Siemens configuration server is carrying a new version of the phone firmware or of the file
with the general settings for your VoIP provider.
If a new version is available, a notification is sent to the handset and the message key
flashes. You can then carry out an automatic update of the firmware (page 59) or of the
VoIP provider settings (page 62).
¤ Open the following Web page: Settings ¢ Miscellaneous.
¤ Click the Yes option next to Automatic check for software/profile updates to activate the
¤
automatic version check.
Click No if you do not want a version check to be carried out.
Click Set to save the changes.
Activating VoIP status message display
Display VoIP status messages on your handset when there are VoIP connection problems.
These messages give you information on the status of a connection and contain a providerspecific status code that helps the service team when they are analysing the problem.
¤ Open the following Web page: Settings ¢ Miscellaneous.
¤ Click the Yes option next to Show VoIP status on handset to activate the status message
¤
display.
If you click No, no VoIP status messages are displayed.
Click Set to save the changes.
Please note:
Version 2, 21.12.2006
A table with possible status codes and their meaning can be found in the appendix on page 116.
107
CE 450 IP R / IM-Ost english / A31008-M1817-R601_1-7619 / web_server.fm / 02.03.2007
Checking status information via your phone
Checking status information via your phone
General information about your phone is displayed.
¤ In the menu list, click on the Status tab.
The following information is displayed:
IP Configuration
IP address
The phone's current IP address within the local network. For assigning the IP address,
see page 87.
MAC address
The phone's device address.
Software
Version 2, 21.12.2006
Firmware version
Version of the firmware currently downloaded. You can download updates of the
firmware on your phone (page 58). Firmware updates are available on the Internet.
EEPROM version
Version of your phone's EEPROM storage chip (page 137).
108
CE 450 IP R / IM-Ost english / A31008-M1817-R601_1-7619 / web_server.fm / 02.03.2007
Messaging
Messaging
Your Gigaset CE 460 IP R base station has messaging functions that you can use via a messaging-capable handset, e.g. a Gigaset S45 handset. The handset must be registered with
your base station.
The following messaging functions are available:
u Messenger functions
The messenger client in your base station enables instant messaging (immediate
message transfer, chatting). The phone supports the XMPP messenger (Jabber).
u E-mail functions
Your telephone checks at regular intervals whether new messages have arrived in your
incoming e-mail server. New e-mail messages are displayed by means of e-mail notifications on a handset with messaging functionality (sender and subject of the e-mail).
Saving messenger access data
Version 2, 21.12.2006
In order to be able to use your base station's messenger functions, you need to register a
handset with messaging capability and save the access data for your messenger server in
the phone.
Your base station is already registered with the Gigaset.net Jabber server. An account has
been assigned to the base station. You can chat to other Gigaset.net subscribers via this
account. To do this you need to create a buddy list on the PC (see "Setting up Gigaset.net
Jabber account" on page 110).
You can also register with another instant messaging provider that supports XMPP
Messenger (Jabber).
In order for you to use your phone's messenger to "go online" and "chat", you must save the
address of the messenger server and your access data on the phone via the Web configurator.
You can define a Resource name and a Priority for your phone. Both are required if you are
logged in (online) with the messenger server with several devices (phone, desktop PC and
laptop) at the same time using the same Jabber ID.
The Resource name is used to distinguish between the devices. The phone cannot log in
with the messenger server if it does not have a resource name.
You should assign a Priority, as each message will only be sent to one device for each Jabber
ID. The Priority determines which of the devices receives the message.
Example: You are online using one of your phone's handsets and your PC both at the same
time. You have assigned your phone (Resource name "phone") Priority 5 and your PC
(Resource name "PC") priority 10. In this case, any message addressed to your Jabber ID will
be sent to your phone.
109
CE 450 IP R / IM-Ost english / A31008-M1817-R601_1-7619 / web_server.fm / 02.03.2007
Messaging
Making settings
¤ Open the following Web page: Settings ¢ Messaging ¢ Messenger.
¤ In the Messenger Account field, select whether you wish to use the Gigaset Net Jabber
¤
¤
¤
¤
¤
¤
server or another provider's messenger server (Other).
The access data for Gigaset.net is already stored in the base station. It is displayed in Jabber ID, Authentication password and Jabber server. With this data you can also register with
the Gigaset.net Jabber server through your PC.
Enter the user ID (max. 50 characters) and password (max. 20 characters) that you used
to register with the messenger server in the Jabber ID and Authentication password
fields.
If you have selected Messenger Account = Gigaset Net, the fields are preset with your
Gigaset.net account.
Enter the IP address or the DNS name of the messenger server in the Jabber server field.
Max. 74 alphanumeric characters.
If you have selected Messenger Account = Gigaset Net, the field is preconfigured with the
name of the Gigaset.net server.
Enter the number of the communication port on the messenger server in the Jabber
server port field. The default port is 5222.
The port number is preset if you have Messenger Account = Gigaset Net.
Enter a resource name (max. 20 characters) in the Resource field.
The default is: phone.
Enter the priority for your phone in the Priority field. Select a number between -128
(highest priority) and 127 (lowest priority) for the priority.
The default is: 5
Click Set.
Setting up Gigaset.net Jabber account
Your phone is already registered with the Gigaset.net Jabber server. An account has been
assigned to your phone.
To be able to chat to other Gigaset.net subscribers via this account, you have to add the
desired Gigaset.net subscriber to your contact list (buddy list) on the PC. You can use any
conventional Jabber client for this (e.g. PSI, Miranda; see e.g. http://www.swissjabber.ch).
Do the following so you can use your Gigaset.net Jabber account:
¤ Start the phone Web configurator, open the Web page Settings ¢ Messaging
¢ Messenger and select Messenger Account in the Gigaset Net field. Your account data is
Version 2, 21.12.2006
¤
¤
¤
displayed in Jabber ID and Authentication password. You will need these to create a buddy
list via the Jabber client on the PC.
Start your Jabber client on the PC.
Enter your Gigaset.net Jabber ID in the Jabber client. The Jabber ID consists of your
Gigaset.net number and "@jabber.gigaset.net"
Example: 21721123901#9@jabber.gigaset.net
Then enter your Authentication password.
110
CE 450 IP R / IM-Ost english / A31008-M1817-R601_1-7619 / web_server.fm / 02.03.2007
Messaging
Please note:
– Do not select the option "Create new account". Your Gigaset.net Jabber account has already been
created in Gigaset.net.
– The option "SSL connection" must be deactivated in the Jabber client.
¤ Now you can enter Gigaset.net subscribers as contacts (buddies).
For the Jabber ID for the relevant subscriber, enter their Gigaset.net number along with
"@jabber.gigaset.net" (example: 2141524901#9@jabber.gigaset.net).
A request to "Add to contact list" will be sent to the subscriber.
If the subscriber accepts this request, they will be added to your buddy list. This updated
buddy list will be displayed on the handset the next time the messenger is rebooted. To
reboot: Disconnect from the messenger server if necessary and then go online again.
Please note:
For how to go online with your Gigaset S45 handset and chat to buddies or call buddies, please refer
to the detailed user guide for the Gigaset S450 IP on the Internet at: www.siemens.com/gigaset.
Making e-mail settings
You must store the IP address/DNS name of your incoming e-mail server and your personal
access data in the phone and activate the e-mail check with the incoming e-mail server, so
that the phone can connect to the incoming e-mail server and your mailbox.
Making settings
¤ Open the following Web page: Settings ¢ Messaging ¢ E-Mail.
¤ Enter the user name (account name) agreed with the Internet provider (max. 50 characters) in the Authentication Name field.
¤ Enter the password that you agreed with your provider for accessing the incoming
e-mail server (max. 20 characters; case sensitive) in the Authentication password field.
¤ Enter the name of the incoming e-mail server (POP3 server) (max. 74 characters) in the
POP3 Server field.
¤ From the Check for new E-Mail list select the time interval at which your phone should
¤
check if new messages have arrived in your incoming e-mail server. Select Never to deactivate the prompt. Select one of the other values to activate the prompt for new e-mail
messages.
Only activate the prompt if a handset with messaging capability (e.g. Gigaset S45) is
registered to your base station.
Click the Set button to save the settings in your phone.
Please note:
Version 2, 21.12.2006
For how e-mail notifications are displayed on a Gigaset S45 IP handset and opened for reading, please
refer to the detailed user guide for the Gigaset S450 IP on the Internet at: www.siemens.com/gigaset.
111
CE 450 IP R / IM-Ost english / A31008-M1817-R601_1-7619 / appendix.fm / 02.03.2007
Symbols and typographical conventions used
Appendix
Symbols and typographical conventions used
This section explains the meaning of certain symbols and typographical conventions that
are used in this user guide.
~
Enter digits or letters.
§Menu§
The display functions currently in the bottom display line are shown in reversed
highlights. Press the relevant display key to launch the function.
q
Press up or down on the control key, e.g. when scrolling.
c / Q / P etc.
Press the matching key on the handset.
External Calls / Internal Calls (example)
Select one of the menu functions (External Calls or Internal Calls) from the list
and press §OK§.
§Menu§ ¢ Audio Settings ¢ Ringer Melody (example)
Press §Menu§. Select Audio Settings using q and press §OK§. Select Ringer Melody
using q and press §OK§.
Care
¤ Wipe down the base station and handset with a damp cloth (no solvents) or an anti-
static cloth.
Never use a dry cloth. This can cause a build up of static.
Contact with liquid
!
Version 2, 21.12.2006
If the handset has come into contact with liquid:
¤ Switch the handset off and remove the batteries immediately.
¤ Allow the liquid to drain from the handset.
¤ Pat all parts dry, then with the battery compartment open and the keypad facing down
place the handset in a dry, warm place for at least 72 hours (not in a microwave, oven
etc.).
¤ Do not switch on the handset again until it is completely dry.
When it has fully dried out, you will normally be able to use it again.
112
CE 450 IP R / IM-Ost english / A31008-M1817-R601_1-7619 / appendix.fm / 02.03.2007
Questions and answers
Questions and answers
If you have any questions about using your phone, visit us at www.siemens.com/gigasetcustomercare at any time. The table below contains a list of common problems and possible solutions.
Please note:
To support the service team, it is helpful if you have the following information to hand:
– The version of the firmware and the MAC address for your base station router, together with the
version of the firmware, of the EEPROM and the MAC address for your base station phone.
You can check this information using the router Web configurator (page 84) or the phone Web
configurator (page 108). For how to check the phone's MAC address on your handset, turn to
page 63.
– VoIP status code (page 116)
For problems with VoIP connections, you should set VoIP status messages to be displayed on your
handset (page 62, page 107). These messages contain a status code that helps when the problem
is analysed.
The display is blank.
1. The handset is not switched on.
Press and hold the end call key a.
¥
2. The battery is flat.
Charge the battery or replace it (page 8).
¥
The keys of a handset do not respond when pressed.
The keypad lock is activated.
Press and hold the hash key # (page 31).
¥
Base flashes in the display.
1. The handset is outside the range of the base station.
Move the handset closer to the base station.
¥
2. The base station is not switched on.
Check the base station's mains adapter (page 12).
¥
3. An update of the base station firmware is currently being conducted (page 58, page 106).
Please wait until the update is complete.
¥
Please Register flashes in the display.
The handset is not registered.
Register the handset (page 48).
¥
Handset does not ring.
The ringer is switched off.
Activate the ringer (page 54).
¥
The other party cannot hear you.
You have pressed the §INT§ display key. The handset is "muted".
Switch on the microphone again (page 30).
Version 2, 21.12.2006
¥
113
CE 450 IP R / IM-Ost english / A31008-M1817-R601_1-7619 / appendix.fm / 02.03.2007
Questions and answers
You hear an error tone when keying an input
(a descending tone sequence).
Action has failed/invalid input.
Repeat the operation.
Watch the display and refer to the user guide if necessary.
¥
You have forgotten the system PIN or the router password.
¥
¥
If you have forgotten the system PIN, you can reset the base station with the key on the base station (page 57).
If you have forgotten the router password, you can reset the base station via the menu (page 57).
You have made a call via VoIP but cannot hear the other participant.
1. Port forwarding is activated on your router, but no permanent IP address has been assigned to your
phone.
Assign the phone a static IP address (page 87) and update the port forwarding settings if necessary (page 76).
¥
2. STUN is enabled on your base station phone or the local SIP port for the base station phone is outside the range 5056 - 5071. As the NAT for your router is symmetric, malfunctions can still occur
during outgoing calls.
Disable STUN (page 94) and check the settings for the local SIP port (page 102).
Enter an outbound proxy (if one has been made available by your VoIP provider) and activate
the outbound proxy mode Auto or Always (page 94).
If the NAT for your router is not the only NAT between the phone and the SIP server (Internet connection via another LAN) and if no outbound proxy is available:
Assign the phone a static IP address (page 87) and enable port forwarding to the phone for the
SIP and RTP port on the router (page 76). If necessary select the local SIP port for the phone so
that it is not in the range 5056 - 5071 (page 102).
¥
¥
¥
You cannot make calls via VoIP. The display shows Server not accessible!.
¥ First wait a few minutes. This is often a short-term event that corrects itself after a short time.
If the message is still displayed, proceed as follows:
¥ Check your base station's cable connection to the Internet.
¥ Check whether the phone is connected to the LAN. For example,set a ping command on the
Version 2, 21.12.2006
¥
114
phone (ping s <local IP address of the phone>). The base station router may not have been able
to assign an IP address to the phone. Check the settings on the router, you may have to activate
the DHCP server.
If a static IP address is assigned to the base station phone, check whether the IP address settings
for the base station phone and base station router are compatible. Please note the following:
– The IP address for the phone must belong to the address block for the router, i.e. the first three
parts of the IP addresses for the phone and the router in subnet mask 255.255.255.0 must be
the same.
– The IP address for the phone must not be assigned to any other LAN subscriber. If the DHCP
server for the router is enabled, no static IP address can belong to the address block that is
reserved for dynamically assigning IP addresses (default setting: 192.168.1.100 –
192.168.1.150)
CE 450 IP R / IM-Ost english / A31008-M1817-R601_1-7619 / appendix.fm / 02.03.2007
Questions and answers
You cannot make calls via VoIP. The display shows SIP registration failed!.
First wait a few minutes. This is often a short-term event that corrects itself after a short time.
The message may still be displayed for the following reasons:
¥
1. The details for your VoIP account (Username, Authentication Name and Authentication Password) may
be incomplete or incorrect.
Check your information. In particular, check your use of upper and lower case.
¥
2. The general settings for your VoIP provider are incomplete or incorrect (incorrect server address).
Start the Web configurator and check the settings.
¥
You cannot establish a connection to the phone with your PC's Web browser.
¥
¥
¥
¥
When establishing a connection, check the phone's local IP address that has been entered. An IP
address that has been dynamically assigned can change when the router is rebooted. You can
check the IP address on your handset (page 60).
Check the LAN connection between the PC and base station.
Check that your base station phone can be reached. For example,transmit a ping command to
your base station phone from your PC.
You have tried to reach the phone via a secure http (https://...). Try again with http://....
You cannot be reached for calls from the Internet.
¥
¥
¥
¥
Check whether your base station is connected to the Internet. The Internet Status for your base station router is displayed on the start page of the router Web configurator.
There is no entry for your phone in your router's routing table. Check the settings for the NAT
refresh time (page 94).
Your phone is not registered with the SIP service.
You have entered the incorrect user ID/user identification or the incorrect domain for your VoIP
account (page 91).
No firmware update or VoIP profile download is carried out for the base station phone.
1. If Not possible! Try later! is displayed, the VoIP line may be busy or a download/update is already
being carried out.
Repeat the process at a later time.
¥
2. If File corrupt! is displayed, the firmware or profile file may be invalid.
Please only use firmware and downloads that are made available on the preconfigured Siemens server (page 106) or at www.siemens.com/gigasetcustomercare.
¥
3. If Server not available! is displayed, the download server may not be accessible.
The server is currently not accessible. Repeat the process at a later time.
You have changed the preconfigured server address (page 106). Correct the address. If necessary, reset the base station.
¥
¥
4. If Transmission error XXX is displayed, an error occurred in the transmission of the file. An HTTP error
code is displayed for XXX.
Repeat the process. If the error occurs again, consult the Service department.
¥
5. If Please check IP settings! is displayed, your phone may not be connected to the Internet.
Check the cable connections between the base station and the Internet.
Check whether the phone is connected to the LAN, i.e. it can be reached at its IP address.
Version 2, 21.12.2006
¥
¥
115
CE 450 IP R / IM-Ost english / A31008-M1817-R601_1-7619 / appendix.fm / 02.03.2007
Questions and answers
VoIP status codes
Version 2, 21.12.2006
If you have problems with your VoIP connections, activate the Status on HS function
(page 63, page 107). You will then receive a VoIP status code that will support you in problem analysis. Also enter the code during problem analysis by the Service department.
In the following tables you will find the meanings of the most important status codes and
messages.
Status
code
Meaning
0x300
The called party can be reached under several phone numbers. If the VoIP provider supports
this, a list of the phone numbers is transmitted as well as the status code. The caller can
select to which number he wants to make the connection.
0x301
Permanently redirected.
The called party can no longer be reached under this number. The new number is transmitted to the phone together with the status code, and the phone then no longer accesses the
old number but dials the new address immediately.
0x302
Temporarily redirected.
The phone is informed that the called party cannot be reached under the number dialled.
The duration of redirecting is time-limited. The phone is also informed of the duration of
redirecting.
0x305
The query is redirected to another proxy server, e.g. to balance query loads. The phone will
make the same query once again to another proxy server. This is not a redirection of the
address per se.
0x380
Other service:
The query or the call could not be made. But the phone is notified what other options there
are to be able to connect the call.
0x400
Wrong call.
0x401
Not authorised.
0x403
The requested service is not supported by the VoIP provider.
0x404
Wrong phone number.
No subscriber on this number.
Example: In a local call you have not dialled the area code although your VoIP provider does
not support local calls.
0x405
Method not permitted.
0x406
Not acceptable.
The requested service cannot be provided.
0x407
Proxy authentication required.
0x408
Calling partner cannot be reached (e.g. account cancelled).
0x410
The requested service is not available from the VoIP provider.
0x413
Message is too long.
0x414
URI is too long.
0x415
Query format is not supported.
116
CE 450 IP R / IM-Ost english / A31008-M1817-R601_1-7619 / appendix.fm / 02.03.2007
Version 2, 21.12.2006
Questions and answers
Status
code
Meaning
0x416
URI is faulty.
0x420
Wrong ending.
0x421
Wrong ending.
0x423
The requested service is not supported by the VoIP provider.
0x480
The dialled number is temporarily unavailable.
0x481
The recipient is not available.
0x482
Double service query.
0x483
Too many "hops":
The query was rejected because the service server (proxy) has decided that this query has
already run through too many service servers. The maximum number was previously specified by the original sender of the query.
0x484
Wrong number:
In most cases this response means that you have simply omitted one or more digits in the
phone number.
0x485
The URI dialled is not unique and cannot be processed by the VoIP provider.
0x486
The called party is busy.
0x487
General faults:
The call was interrupted before a call was established. The status code confirms receipt of
the interruption signal.
0x488
The server cannot process the query because the data entered in the media description is
not compatible.
0x491
The server notifies that the query will be processed as soon as a previous query has been
completed.
0x493
The server rejects the query because the phone cannot decrypt the message. The sender
has used an encryption method that neither the server nor the receiver phone can decrypt.
0x500
The proxy or the receiving device has discovered a fault while executing the query, which
makes further execution of the query impossible. In this case, the caller or the phone displays the fault and repeats the query after a few seconds. The number of seconds after
which the query can be repeated may be transmitted to the caller or to the phone by the
receiving device.
0x501
The query cannot be processed by the recipient because the recipient does not have the
functionality that the caller requires. If the recipient understands the query but does not
process it because the sender does not have the necessary rights or the query is not permitted in the current context, a 405 is sent instead of 501.
0x502
In this case, the receiving device that transmits this error code is a proxy or a gateway and
has received an invalid response from its gateway via which this query is to be processed.
0x503
The query cannot currently be processed by the receiving device or the proxy because the
server is either overloaded or is being serviced. If it is possible for the query to be repeated
in the foreseeable future, the server informs the caller or the phone of this.
0x504
Time limit exceeded at the gateway.
117
CE 450 IP R / IM-Ost english / A31008-M1817-R601_1-7619 / appendix.fm / 02.03.2007
Version 2, 21.12.2006
Questions and answers
Status
code
Meaning
0x505
The server rejects the query because the indicated version number of the SIP protocol does
not at least concur with the version that the server or the SIP device uses that is involved in
this query.
0x515
The server rejects the query because the message exceeds the maximum permitted size.
0x600
The called party is busy.
0x603
The called party has rejected the call.
0x604
The called URI does not exist.
0x606
The communication settings are not acceptable.
0x701
The called party has hung up.
0x703
Connection interrupted because of time-out.
0x704
Connection interrupted because of a SIP error.
0x705
Wrong dialling tone.
0x706
No connection established.
0x751
Busy tone:
No codec match between the calling and called subscriber.
0x810
General socket layer error: User is not authorised.
0x811
General socket layer error:
Wrong socket number.
0x812
General socket layer error: Socket is not connected.
0x813
General socket layer error:
Memory error.
0x814
General socket layer error: Socket not available - check IP settings / connection problem /
VoIP setting incorrect.
0x815
General socket layer error:
Illegal application on the socket interface.
118
CE 450 IP R / IM-Ost english / A31008-M1817-R601_1-7619 / appendix.fm / 02.03.2007
Searching for service information
Searching for service information
You may need the service information of your device (base station and handset) for
Customer Services.
Base station service information
Precondition: You are conducting an external call. The connection has been established
for at least 8 sec.
§Menu§ ¢ Service Info
Confirm selection with §OK§.
The following information is displayed:
1: Serial number of the base station (RFPI)
2: Serial number of your handset (IPUI)
3: Informs the service employees of the base station phone settings (in hex diagram),
e.g. about the number of registered handsets, repeater mode. The last 4 digits indicate the
number of operating hours (hexadecimal).
4: Variant: Version (digits 3 to 5) of the firmware that is currently loaded on the base station
phone.
5: Gigaset.net number of your phone. This number can be used to test online connections
and VoIP telephony irrespective of the VoIP provider.
Service information of the handset
In the handset idle status:
¤ Press §Menu§.
¤ Enter * # 0 6 #.
Version 2, 21.12.2006
The following information is displayed via the handset:
1: Serial number (IPUI)
2: Number of operating hours
3: Variant, version of handset software
119
CE 450 IP R / IM-Ost english / A31008-M1817-R601_1-7619 / appendix.fm / 02.03.2007
Service (Customer Care)
Service (Customer Care)
You can get assistance easily when you have technical questions or questions about how
to use your device by using our online support service on the Internet at:
http://www.siemens.com/gigasetcustomercare
This site can be accessed at any time wherever you are. It will give you 24/7 support for all
our products. It also a list of FAQs and answers plus user guides for you to download. You
will also find frequently asked questions and answers in the Questions and Answers
section of this user guide in the appendix.
If the device needs to be repaired, please contact one of our Customer Care Centers:
Abu Dhabi. . . . . . . . . . . . .97 12 62 23 800
Argentina . . . . . . . . . . . . . 0800-888-9878
Australia . . . . . . . . . . . . . . . .1300 665 366
Austria . 05 17 07 50 04 (0,065 Euro/Min.)
Bahrain . . . . . . . . . . . . . . .97 31 73 11 173
Belgium . . . . . . . . . . . . . . . . 0 78 15 66 79
Bosnia Herzegovina . . . . . . . . 033 276 649
Brazil . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Grande Capitais e Regiões Metropolitanas:
. . . . . . . . . . . . . . . . . . . . . . . . . 4003 3020
. . . . . . . . . . . . . . . . . . . . . . . . . (US$ 0,59)
Demais localidades: . . . . . 0800 707 1248
. . . . . . . . . . . . . . . . . . . . . . . . . (US$ 0,59)
Bulgaria. . . . . . . . . . . . . . . . . 02 873 94 88
Canada . . . . . . . . . . . . . . . . 701-355-3984
China . . . . . . . . . . . . . 0 21 400 670 6007
Croatia . . . . . . . . 016 10 53 81 (0,23 Kun)
Czech Republic . . . . . . . . . . . . 233 032 727
Denmark . . . . . . . . . . . . . . . . . 35 25 86 00
Dubai . . . . . . . . . . . . . . . .97 14 39 69 944
Egypt. . . . . . . . . . . . . . . . . . . 202 7623441
Finland . . . . . . . . . . . . . . . . 09 23 11 34 25
France. . . . . . . . . . . . . . . . . 01 56 38 42 00
Germany .01805 333 222 (0,14 Euro/Min.)
Greece . . . . . 801 11 11 11 6 (0,026 Euro)
Hungary . . . . . . . . . 06 14 71 24 44 (27 Ft)
Ireland . . . . . . . . . . . . . . . . 18 50 77 72 77
Italy. . . . . . . . . . . . . . . . . . . . 199 15 11 15
Kuwait . . . . . . . . . . . . . . . . 96 52 44 4200
Latvia . . . . . . . . . . . . . . . . . . . . 7 50 11 18
Luxembourg . . . . . . . . . . . 40 66 61 56 40
Malaysia. . . . . . . . . . . . . . . .603 77124304
Malta . . . . . . . . . . . . . . +353 21 4940 632
Mexico . . . . . . . . . . . . . .01 80 07 11 00 03
Netherlands
. . . . . . . . .0900-3333102 (0,25 Euro/min.)
New Zealand . . . . . . . . . . . 08 00 27 43 63
Norway . . . . . . . . . . . . . . . . . . 22 70 84 00
Oman. . . . . . . . . . . . . . . . 96 82 47 09 281
Poland . . . . . . . . . . . . . . . . . 0 801 140 160
Portugal . . . . . . . . . . . . . (351) 214245145
Romania . . . . . . . . . . . . . . 02 12 04 60 00
Russia. . . . . . . . . . . . . . . 8 (495) 228 1312
Serbia. . . . . . . . . . . . . . . . . 01 13 07 00 80
Singapore . . . . . . . . . . . . . . . . 62 27 11 18
Slovak Republic
. . . . . . . . . . . . . 02 59 68 22 66 (4,428 sk)
Slovenija . . . . . 0 14 74 63 36 (6,30 Tolar)
South Africa. . . . . . . . . . . . 08 60 10 11 57
Spain . . . . . . . . . . . . . . . . . . . . 902 103935
Sweden . . . . . . . . . . . . . . . . 0 87 50 99 11
Switzerland
. . . . . . . . . 08 48 21 20 00 (0,08 SFr./Min.)
Taiwan . . . . . . . . . . . . . . . . 02 23 96 10 06
Thailand. . . . . . . . . . . . . . . . . 02 722 1118
Turkey . . . . . . . . . . . . . . . 0 21 64 59 98 59
Ukraine . . . . . . . . . . . .+380-44-451-71-72
United Arab Emirates . . . . . 0 43 66 03 86
United Kingdom . . . . . . . 0 84 53 67 08 12
USA . . . . . . . . . . . . . . . . . 1-866 247-8758
. . . . . . . . . . . . . . . . . . . . . . . . . . . (toll free)
Please address any questions about DSL access and VoIP access to the respective service
provider.
Version 2, 21.12.2006
Please have your record of purchase ready when calling.
Replacement or repair services are not offered in countries where our product is not sold by
authorised dealers.
120
CE 450 IP R / IM-Ost english / A31008-M1817-R601_1-7619 / appendix.fm / 02.03.2007
Authorisation
Authorisation
This device, in combination with an external modem, is intended for connection to your
telecomunications network ( LAN IEEE 802.3 ).
Country-specific requirements have been taken into consideration.
We, Siemens Home and Office Communication Devices GmbH & Co. KG, declare that this
device meets the essential requirements and other relevant regulations laid down in
Directive 1999/5/EC.
A copy of the 1999/5/EC Declaration of Conformity is available at this Internet address:
http://www.siemens.com/gigasetdocs.
Specifications
Recommended batteries
(Valid at the time of going to press)
Technology:
Nickel-metal-hydride (NiMH)
Size:
AAA
Voltage: 1.2 V
Capacity: 550-850 mAh
Version 2, 21.12.2006
We recommend the following battery types, because these are the only ones that guarantee the specified operating times, full functionality and long service life:
u Sanyo Twicell 650
u Sanyo Twicell 700
u Sanyo NiMH 800
u Panasonic 700 mAh "for DECT"
u GP 550mAh
u GP 700mAh
u GP 850mAh
u Yuasa Technology AAA Phone 600
u Yuasa Technology AAA Phone 700
u Yuasa Technology AAA 800
u VARTA Phone Power AAA 700mAh
The device is supplied with two recommended batteries.
121
CE 450 IP R / IM-Ost english / A31008-M1817-R601_1-7619 / appendix.fm / 02.03.2007
Specifications
Handset operating times/charging times
(The operating and charging times apply only when using the recommended batteries).
The operating time of your Gigaset depends on the age of the batteries and the way they
are used. (All times are maximum possible times).
The following information relates to batteries with a capacity of 650 mAh.
Standby time
around 125 hours (5 days)
Talktime
around 13 hours
Charging time
around 7.5 hours
Version 2, 21.12.2006
At the time of going to print, batteries up to 850 mAh were available and had been tested
in the system. Due to the constant progression in battery development, the list of recommended batteries in the FAQ section of the Gigaset Customer Care pages is regularly
updated:
www.siemens.com/gigasetcustomercare
122
CE 450 IP R / IM-Ost english / A31008-M1817-R601_1-7619 / appendix.fm / 02.03.2007
Specifications
Base station power consumption
Around 1 W, depending on the current status.
General specifications
Interfaces
Ethernet
DECT standard
is supported
GAP standard
is supported
No. of channels
60 duplex channels
Radio frequency range
1880–1900 MHz
Duplex method
Time multiplex, 10 ms frame length
Channel grid
1728 kHz
Bit rate
1152 kbit/s
Modulation
GFSK
Language code
32 kbit/s
Transmission power
10 mW, average power per channel
Range
up to 300 m outdoors, up to 50 m indoors
Base station power supply
230 V ~/50 Hz
Version 2, 21.12.2006
Environmental conditions in operation +5 °C to +45 °C, 20 % to 75 % relative humidity
Codecs
G711, G726, G729AB with VAD/CNG
Quality of Service
TOS, DiffServ
Protocols
DECT, SIP, RTP, DHCP, NAT Traversal (STUN)
Base station dimensions
105 x 155 x 46 mm (L x W x D)
Dimensions, handset
141 x 53 x 31 mm (L × W × H)
Base station weight
160 g
Weight of handset with battery
116 g
123
CE 450 IP R / IM-Ost english / A31008-M1817-R601_1-7619 / appendix.fm / 02.03.2007
Writing and editing a text message
Writing and editing a text message
The following rules apply when writing a text:
u The cursor is controlled with t s.
u Characters are added to the left of the cursor.
u Press the hash key # briefly to switch from "Abc" mode to "123", from "123" to "abc",
and from "abc" to "Abc" (upper case: 1st letter upper case, all others lower case). Press
the hash key # before entering the letter.
u Press the hash key # 3 times: shows the selection line of the characters assigned to
the hash key.
u The first letter of the name of directory entries is automatically capitalised, followed by
lower case letters.
Editing text
When you press a key and hold it, the characters of that key appear in the bottom display
line and are highlighted one after the other. When you release the key, the highlighted
character is inserted into the input field. For how to enter special characters, see page 125.
The display briefly shows whether upper or lower case letters or digits is selected when you
switch from one mode to the next: the bottom text line displays "abc -> Abc", "Abc -> 123"
or "123 -> abc".
Order of directory entries
Version 2, 21.12.2006
The directory entries are usually sorted in alphabetical order. Spaces and digits take first
priority. The sort order is as follows:
1. Space (shown here as s)
2. Digits (0–9)
3. Letters (alphabetical)
4. Other characters
To get round the alphabetical order of the entries, insert a space or a digit in front of the
name. These entries will then move to the beginning of the directory. Names that you have
prefixed with a star will move to the end of the directory.
124
CE 450 IP R / IM-Ost english / A31008-M1817-R601_1-7619 / appendix.fm / 02.03.2007
Writing and editing a text message
Entering special characters
Standard characters
1
1x
*)
**)
Space
Space
Q
.
P
*
#
Abc-->
123
2x
1
Â
,
/
123 -->
3x
£
1
?
(
#
4x
$
â
!
)
@
5x
¥
£
0
<
\
6x
¤
abc
$
+
=
&
7x
¥
-
>
§
8x
¤
:
%
9x
¿
10x
¡
11x
“
12x
‘
13x
;
14x
_
Version 2, 21.12.2006
*) Directory and other lists
125
CE 450 IP R / IM-Ost english / A31008-M1817-R601_1-7619 / appendix.fm / 02.03.2007
Writing and editing a text message
Greek
1x
1
*)
**)
Space
Space
Q
.
P
*
#
Abc-->
123
Â
,
£
1
?
$
â
!
)
@
5x
£
0
<
\
6x
$
+
=
&
7x
-
>
§
8x
:
%
9x
“
10x
‘
11x
;
12x
_
2x
3x
4x
1
Version 2, 21.12.2006
123 -->
abc
*) Directory and other lists
126
/
(
#
CE 450 IP R / IM-Ost english / A31008-M1817-R601_1-7619 / appendix.fm / 02.03.2007
Gigaset CE 460 IP R – Free software
Gigaset CE 460 IP R – Free software
Your Gigaset CE 460 IP R's firmware includes free software that is licensed under the GNU
Lesser General Public License. This free software was developed by a third party and is protected by copyright. You will find the licence text in its original English version on the pages
that follow.
The software is provided free of charge. You are authorised to use this free software in
accordance with the above-mentioned licence conditions. In the event of contradictions
between these licence conditions and the licence conditions that apply for the software
according to Siemens Home and Office Communication Devices GmbH & Co. KG, the
above-mentioned licence conditions shall take precedence for the free software.
The GNU Lesser General Public License (LGPL) is supplied with this product. You can also
download the licence conditions from the Internet:
u The LGPL is available on the Internet at:
http://www.gnu.org/copyleft/lesser.html
u The source text, including copyright notices for free software, is currently available
on the Internet at:
http://www.siemens.com/developer/c455ip
For more information and Internet links to the source text of the free software, see the
Online Support pages on the Internet at:
www.siemens.com/gigasetcustomercare
If it is not already supplied with the product, you can request the source text, including
copyright notices, from Siemens. There is a charge to cover the cost of copying and postage. Please submit this request by e-mail or fax to the following address or fax number
within 3 years of purchasing this product. Please state the exact device type plus the version number of the installed device software.
Small Parts Dispatch Com Bocholt
E-mail: kleinteileversand.com@siemens.com
Version 2, 21.12.2006
Fax:
+49 2871 / 91 30 29
Use of the free software contained in this product extending beyond the program
sequence intended by Siemens is at the user's own risk – i.e. there shall be no claims for
liability for defects against Siemens Home and Office Communication Devices GmbH & Co.
KG. The GNU Lesser General Public License contains notes regarding the author's liability
for defects or that of other proprietors of the free software.
You shall have no right to assert a claim against Siemens Home and Office Communication
Devices GmbH & Co. KG based on liability for defects, if a defect in the product is or could
be due to changes you have made to the programs or their configuration. Furthermore,
you shall have no right to assert a claim against Siemens Home and Office Communication
Devices GmbH & Co. KG based on liability for defects if the free software infringes the
copyright of third parties.
Siemens shall not provide technical support for the software, including the free software
included within it, if it has been changed.
127
CE 450 IP R / IM-Ost english / A31008-M1817-R601_1-7619 / appendix.fm / 02.03.2007
Gigaset CE 460 IP R – Free software
GNU LESSER GENERAL PUBLIC LICENSE
Version 2.1, February 1999
Copyright (C) 1991, 1999 Free Software Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA
02111-1307 USA
Everyone is permitted to copy and distribute verbatim copies of this license document, but changing
it is not allowed.
[This is the first released version of the Lesser GPL. It also counts as the successor of the GNU Library
Public License, version 2, hence the version number 2.1.]
Version 2, 21.12.2006
Preamble
The licenses for most software are designed to take away your freedom to share and change it. By contrast, the GNU General Public Licenses are intended to guarantee your freedom to share and change
free software--to make sure the software is free for all its users.
This license, the Lesser General Public License, applies to some specially designated software packages--typically libraries--of the Free Software Foundation and other authors who decide to use it. You
can use it too, but we suggest you first think carefully about whether this license or the ordinary
General Public License is the better strategy to use in any particular case, based on the explanations
below.
When we speak of free software, we are referring to freedom of use, not price. Our General Public
Licenses are designed to make sure that you have the freedom to distribute copies of free software
(and charge for this service if you wish); that you receive source code or can get it if you want it; that
you can change the software and use pieces of it in new free programs; and that you are informed that
you can do these things.
To protect your rights, we need to make restrictions that forbid distributors to deny you these rights or
to ask you to surrender these rights. These restrictions translate to certain responsibilities for you if
you distribute copies of the library or if you modify it.
For example, if you distribute copies of the library, whether gratis or for a fee, you must give the recipients all the rights that we gave you. You must make sure that they, too, receive or can get the source
code. If you link other code with the library, you must provide complete object files to the recipients,
so that they can relink them with the library after making changes to the library and recompiling it.
And you must show them these terms so they know their rights.
We protect your rights with a two-step method: (1) we copyright the library, and (2) we offer you this
license, which gives you legal permission to copy, distribute and/or modify the library.
To protect each distributor, we want to make it very clear that there is no warranty for the free library.
Also, if the library is modified by someone else and passed on, the recipients should know that what
they have is not the original version, so that the original author's reputation will not be affected by
problems that might be introduced by others.
Finally, software patents pose a constant threat to the existence of any free program. We wish to make
sure that a company cannot effectively restrict the users of a free program by obtaining a restrictive
license from a patent holder. Therefore, we insist that any patent license obtained for a version of the
library must be consistent with the full freedom of use specified in this license.
Most GNU software, including some libraries, is covered by the ordinary GNU General Public License.
This license, the GNU Lesser General Public License, applies to certain designated libraries, and is quite
different from the ordinary General Public License. We use this license for certain libraries in order to
permit linking those libraries into non-free programs.
When a program is linked with a library, whether statically or using a shared library, the combination
of the two is legally speaking a combined work, a derivative of the original library. The ordinary
General Public License therefore permits such linking only if the entire combination fits its criteria of
freedom. The Lesser General Public License permits more lax criteria for linking other code with the
library.
We call this license the "Lesser" General Public License because it does Less to protect the user's freedom than the ordinary General Public License. It also provides other free software developers Less of
an advantage over competing non-free programs. These disadvantages are the reason we use the
ordinary General Public License for many libraries. However, the Lesser license provides advantages in
certain special circumstances.
128
CE 450 IP R / IM-Ost english / A31008-M1817-R601_1-7619 / appendix.fm / 02.03.2007
Gigaset CE 460 IP R – Free software
For example, on rare occasions, there may be a special need to encourage the widest possible use of
a certain library, so that it becomes a de-facto standard. To achieve this, non-free programs must be
allowed to use the library. A more frequent case is that a free library does the same job as widely used
non-free libraries. In this case, there is little to gain by limiting the free library to free software only,
so we use the Lesser General Public License.
In other cases, permission to use a particular library in non-free programs enables a greater number
of people to use a large body of free software. For example, permission to use the GNU C Library in
non-free programs enables many more people to use the whole GNU operating system, as well as its
variant, the GNU/Linux operating system.
Although the Lesser General Public License is Less protective of the users' freedom, it does ensure that
the user of a program that is linked with the Library has the freedom and the wherewithal to run that
program using a modified version of the Library.
The precise terms and conditions for copying, distribution and modification follow. Pay close attention
to the difference between a "work based on the library" and a "work that uses the library". The former
contains code derived from the library, whereas the latter must be combined with the library in order
to run.
GNU LESSER GENERAL PUBLIC LICENSE
Version 2, 21.12.2006
TERMS AND CONDITIONS FOR COPYING, DISTRIBUTION AND MODIFICATION
0. This License Agreement applies to any software library or other program which contains a notice
placed by the copyright holder or other authorized party saying it may be distributed under the terms
of this Lesser General Public License (also called "this License"). Each licensee is addressed as "you".
A "library" means a collection of software functions and/or data prepared so as to be conveniently
linked with application programs (which use some of those functions and data) to form executables.
The "Library", below, refers to any such software library or work which has been distributed under
these terms. A "work based on the Library" means either the Library or any derivative work under
copyright law: that is to say, a work containing the Library or a portion of it, either verbatim or with
modifications and/or translated straightforwardly into another language. (Hereinafter, translation is
included without limitation in the term "modification".)
"Source code" for a work means the preferred form of the work for making modifications to it. For a
library, complete source code means all the source code for all modules it contains, plus any associated interface definition files, plus the scripts used to control compilation and installation of the
library.
Activities other than copying, distribution and modification are not covered by this License; they are
outside its scope. The act of running a program using the Library is not restricted, and output from
such a program is covered only if its contents constitute a work based on the Library (independent of
the use of the Library in a tool for writing it). Whether that is true depends on what the Library does
and what the program that uses the Library does.
1. You may copy and distribute verbatim copies of the Library's complete source code as you receive
it, in any medium, provided that you conspicuously and appropriately publish on each copy an appropriate copyright notice and disclaimer of warranty; keep intact all the notices that refer to this License
and to the absence of any warranty; and distribute a copy of this License along with the Library.
You may charge a fee for the physical act of transferring a copy, and you may at your option offer warranty protection in exchange for a fee.
2. You may modify your copy or copies of the Library or any portion of it, thus forming a work based
on the Library, and copy and distribute such modifications or work under the terms of Section 1 above,
provided that you also meet all of these conditions:
a) The modified work must itself be a software library.
b) You must cause the files modified to carry prominent notices stating that you changed the files and
the date of any change.
c) You must cause the whole of the work to be licensed at no charge to all third parties under the terms
of this License.
129
CE 450 IP R / IM-Ost english / A31008-M1817-R601_1-7619 / appendix.fm / 02.03.2007
Version 2, 21.12.2006
Gigaset CE 460 IP R – Free software
d) If a facility in the modified Library refers to a function or a table of data to be supplied by an application program that uses the facility, other than as an argument passed when the facility is invoked,
then you must make a good faith effort to ensure that, in the event an application does not supply
such function or table, the facility still operates, and performs whatever part of its purpose remains
meaningful.
(For example, a function in a library to compute square roots has a purpose that is entirely welldefined independent of the application. Therefore, Subsection 2d requires that any application-supplied function or table used by this function must be optional: if the application does not supply it, the
square root function must still compute square roots.)
These requirements apply to the modified work as a whole. If identifiable sections of that work are not
derived from the Library, and can be reasonably considered independent and separate works in themselves, then this License, and its terms, do not apply to those sections when you distribute them as
separate works. But when you distribute the same sections as part of a whole which is a work based
on the Library, the distribution of the whole must be on the terms of this License, whose permissions
for other licensees extend to the entire whole, and thus to each and every part regardless of who
wrote it.
Thus, it is not the intent of this section to claim rights or contest your rights to work written entirely
by you; rather, the intent is to exercise the right to control the distribution of derivative or collective
works based on the Library.
In addition, mere aggregation of another work not based on the Library with the Library (or with a
work based on the Library) on a volume of a storage or distribution medium does not bring the other
work under the scope of this License.
3. You may opt to apply the terms of the ordinary GNU General Public License instead of this License
to a given copy of the Library. To do this, you must alter all the notices that refer to this License, so
that they refer to the ordinary GNU General Public License, version 2, instead of to this License. (If a
newer version than version 2 of the ordinary GNU General Public License has appeared, then you can
specify that version instead if you wish.) Do not make any other change in these notices.
Once this change is made in a given copy, it is irreversible for that copy, so the ordinary GNU General
Public License applies to all subsequent copies and derivative works made from that copy.
This option is useful when you wish to copy part of the code of the Library into a program that is not
a library.
4. You may copy and distribute the Library (or a portion or derivative of it, under Section 2) in object
code or executable form under the terms of Sections 1 and 2 above provided that you accompany it
with the complete corresponding machine-readable source code, which must be distributed under the
terms of Sections 1 and 2 above on a medium customarily used for software interchange.
If distribution of object code is made by offering access to copy from a designated place, then offering
equivalent access to copy the source code from the same place satisfies the requirement to distribute
the source code, even though third parties are not compelled to copy the source along with the object
code.
5. A program that contains no derivative of any portion of the Library, but is designed to work with
the Library by being compiled or linked with it, is called a "work that uses the Library". Such a work, in
isolation, is not a derivative work of the Library, and therefore falls outside the scope of this License.
However, linking a "work that uses the Library" with the Library creates an executable that is a derivative of the Library (because it contains portions of the Library), rather than a "work that uses the
library". The executable is therefore covered by this License.
Section 6 states terms for distribution of such executables.
When a "work that uses the Library" uses material from a header file that is part of the Library, the
object code for the work may be a derivative work of the Library even though the source code is not.
Whether this is true is especially significant if the work can be linked without the Library, or if the work
is itself a library. The threshold for this to be true is not precisely defined by law.
If such an object file uses only numerical parameters, data structure layouts and accessors, and small
macros and small inline functions (ten lines or less in length), then the use of the object file is unrestricted, regardless of whether it is legally a derivative work. (Executables containing this object code
plus portions of the Library will still fall under Section 6.)
Otherwise, if the work is a derivative of the Library, you may distribute the object code for the work
under the terms of Section 6.
130
CE 450 IP R / IM-Ost english / A31008-M1817-R601_1-7619 / appendix.fm / 02.03.2007
Version 2, 21.12.2006
Gigaset CE 460 IP R – Free software
Any executables containing that work also fall under Section 6, whether or not they are linked directly
with the Library itself.
6. As an exception to the Sections above, you may also combine or link a "work that uses the Library"
with the Library to produce a work containing portions of the Library, and distribute that work under
terms of your choice, provided that the terms permit modification of the work for the customer's own
use and reverse engineering for debugging such modifications.
You must give prominent notice with each copy of the work that the Library is used in it and that the
Library and its use are covered by this License. You must supply a copy of this License. If the work during execution displays copyright notices, you must include the copyright notice for the Library among
them, as well as a reference directing the user to the copy of this License. Also, you must do one of
these things:
a) Accompany the work with the complete corresponding machine-readable source code for the
Library including whatever changes were used in the work (which must be distributed under Sections
1 and 2 above); and, if the work is an executable linked with the Library, with the complete machinereadable "work that uses the Library", as object code and/or source code, so that the user can modify
the Library and then relink to produce a modified executable containing the modified Library. (It is
understood that the user who changes the contents of definitions files in the Library will not necessarily be able to recompile the application to use the modified definitions.)
b) Use a suitable shared library mechanism for linking with the Library. A suitable mechanism is one
that (1) uses at run time a copy of the library already present on the user's computer system, rather
than copying library functions into the executable, and (2) will operate properly with a modified version of the library, if the user installs one, as long as the modified version is interface-compatible with
the version that the work was made with.
c) Accompany the work with a written offer, valid for at least three years, to give the same user the
materials specified in Subsection 6a, above, for a charge no more than the cost of performing this distribution.
d) If distribution of the work is made by offering access to copy from a designated place, offer equivalent access to copy the above specified materials from the same place.
e) Verify that the user has already received a copy of these materials or that you have already sent this
user a copy.
For an executable, the required form of the "work that uses the Library" must include any data and
utility programs needed for reproducing the executable from it. However, as a special exception, the
materials to be distributed need not include anything that is normally distributed (in either source or
binary form) with the major components (compiler, kernel, and so on) of the operating system on
which the executable runs, unless that component itself accompanies the executable.
It may happen that this requirement contradicts the license restrictions of other proprietary libraries
that do not normally accompany the operating system. Such a contradiction means you cannot use
both them and the Library together in an executable that you distribute.
7. You may place library facilities that are a work based on the Library side-by-side in a single library
together with other library facilities not covered by this License, and distribute such a combined
library, provided that the separate distribution of the work based on the Library and of the other library
facilities is otherwise permitted, and provided that you do these two things:
a) Accompany the combined library with a copy of the same work based on the Library, uncombined
with any other library facilities. This must be distributed under the terms of the Sections above.
b) Give prominent notice with the combined library of the fact that part of it is a work based on the
Library, and explaining where to find the accompanying uncombined form of the same work.
8. You may not copy, modify, sublicense, link with, or distribute the Library except as expressly provided under this License. Any attempt otherwise to copy, modify, sublicense, link with, or distribute
the Library is void, and will automatically terminate your rights under this License. However, parties
who have received copies, or rights, from you under this License will not have their licenses terminated so long as such parties remain in full compliance.
9. You are not required to accept this License, since you have not signed it. However, nothing else
grants you permission to modify or distribute the Library or its derivative works. These actions are prohibited by law if you do not accept this License. Therefore, by modifying or distributing the Library (or
any work based on the Library), you indicate your acceptance of this License to do so, and all its terms
and conditions for copying, distributing or modifying the Library or works based on it.
131
CE 450 IP R / IM-Ost english / A31008-M1817-R601_1-7619 / appendix.fm / 02.03.2007
Gigaset CE 460 IP R – Free software
Version 2, 21.12.2006
10. Each time you redistribute the Library (or any work based on the Library), the recipient automatically receives a license from the original licensor to copy, distribute, link with or modify the Library
subject to these terms and conditions. You may not impose any further restrictions on the recipients'
exercise of the rights granted herein.
You are not responsible for enforcing compliance by third parties with this License.
11. If, as a consequence of a court judgment or allegation of patent infringement or for any other reason (not limited to patent issues), conditions are imposed on you (whether by court order, agreement
or otherwise) that contradict the conditions of this License, they do not excuse you from the conditions of this License. If you cannot distribute so as to satisfy simultaneously your obligations under this
License and any other pertinent obligations, then as a consequence you may not distribute the Library
at all. For example, if a patent license would not permit royalty-free redistribution of the Library by all
those who receive copies directly or indirectly through you, then the only way you could satisfy both
it and this License would be to refrain entirely from distribution of the Library.
If any portion of this section is held invalid or unenforceable under any particular circumstance, the
balance of the section is intended to apply, and the section as a whole is intended to apply in other
circumstances.
It is not the purpose of this section to induce you to infringe any patents or other property right claims
or to contest validity of any such claims; this section has the sole purpose of protecting the integrity
of the free software distribution system which is implemented by public license practices. Many people have made generous contributions to the wide range of software distributed through that system
in reliance on consistent application of that system; it is up to the author/donor to decide if he or she
is willing to distribute software through any other system and a licensee cannot impose that choice.
This section is intended to make thoroughly clear what is believed to be a consequence of the rest of
this License.
12. If the distribution and/or use of the Library is restricted in certain countries either by patents or by
copyrighted interfaces, the original copyright holder who places the Library under this License may
add an explicit geographical distribution limitation excluding those countries, so that distribution is
permitted only in or among countries not thus excluded. In such case, this License incorporates the
limitation as if written in the body of this License.
13. The Free Software Foundation may publish revised and/or new versions of the Lesser General
Public License from time to time. Such new versions will be similar in spirit to the present version, but
may differ in detail to address new problems or concerns.
Each version is given a distinguishing version number. If the Library specifies a version number of this
License which applies to it and "any later version", you have the option of following the terms and conditions either of that version or of any later version published by the Free Software Foundation. If the
Library does not specify a license version number, you may choose any version ever published by the
Free Software Foundation.
14. If you wish to incorporate parts of the Library into other free programs whose distribution conditions are incompatible with these, write to the author to ask for permission. For software which is copyrighted by the Free Software Foundation, write to the Free Software Foundation; we sometimes
make exceptions for this. Our decision will be guided by the two goals of preserving the free status of
all derivatives of our free software and of promoting the sharing and reuse of software generally.
NO WARRANTY
15. BECAUSE THE LIBRARY IS LICENSED FREE OF CHARGE, THERE IS NO WARRANTY FOR THE LIBRARY,
TO THE EXTENT PERMITTED BY APPLICABLE LAW.
EXCEPT WHEN OTHERWISE STATED IN WRITING THE COPYRIGHT HOLDERS AND/OR OTHER PARTIES
PROVIDE THE LIBRARY "AS IS" WITHOUT WARRANTY OF ANY KIND, EITHER EXPRESSED OR IMPLIED,
INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR
A PARTICULAR PURPOSE. THE ENTIRE RISK AS TO THE QUALITY AND PERFORMANCE OF THE LIBRARY IS
WITH YOU. SHOULD THE LIBRARY PROVE DEFECTIVE, YOU ASSUME THE COST OF ALL NECESSARY SERVICING, REPAIR OR CORRECTION.
132
CE 450 IP R / IM-Ost english / A31008-M1817-R601_1-7619 / appendix.fm / 02.03.2007
Gigaset CE 460 IP R – Free software
16. IN NO EVENT UNLESS REQUIRED BY APPLICABLE LAW OR AGREED TO IN WRITING WILL ANY COPYRIGHT HOLDER, OR ANY OTHER PARTY WHO MAY MODIFY AND/OR REDISTRIBUTE THE LIBRARY AS PERMITTED ABOVE, BE LIABLE TO YOU FOR DAMAGES, INCLUDING ANY GENERAL, SPECIAL, INCIDENTAL
OR CONSEQUENTIAL DAMAGES ARISING OUT OF THE USE OR INABILITY TO USE THE LIBRARY (INCLUDING BUT NOT LIMITED TO LOSS OF DATA OR DATA BEING RENDERED INACCURATE OR LOSSES SUSTAINED BY YOU OR THIRD PARTIES OR A FAILURE OF THE LIBRARY TO OPERATE WITH ANY OTHER SOFTWARE), EVEN IF SUCH HOLDER OR OTHER PARTY HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH
DAMAGES.
END OF TERMS AND CONDITIONS
How to Apply These Terms to Your New Libraries
If you develop a new library, and you want it to be of the greatest possible use to the public, we recommend making it free software that everyone can redistribute and change. You can do so by permitting redistribution under these terms (or, alternatively, under the terms of the ordinary General Public
License).
To apply these terms, attach the following notices to the library. It is safest to attach them to the start
of each source file to most effectively convey the exclusion of warranty; and each file should have at
least the "copyright" line and a pointer to where the full notice is found.
<one line to give the library's name and a brief idea of what it does.>
Copyright (C) <year> <name of author>
This library is free software; you can redistribute it and/or modify it under the terms of the GNU Lesser
General Public License as published by the Free Software Foundation; either version 2.1 of the
License, or (at your option) any later version.
This library is distributed in the hope that it will be useful, but WITHOUT ANY WARRANTY; without
even the implied warranty of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
GNU Lesser General Public License for more details.
You should have received a copy of the GNU Lesser General Public License along with this library; if
not, write to the Free Software Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307
USA
Also add information on how to contact you by electronic and paper mail.
You should also get your employer (if you work as a programmer) or your school, if any, to sign a
"copyright disclaimer" for the library, if necessary. Here is a sample; alter the names:
Version 2, 21.12.2006
Yoyodyne, Inc., hereby disclaims all copyright interest in the library `Frob' (a library for tweaking
knobs) written by James Random Hacker. <signature of Ty Coon>, 1 April 1990 Ty Coon, President of
Vice
133
CE 450 IP R / IM-Ost english / A31008-M1817-R601_1-7619 / accessories_SAG.fm / 02.03.2007
Accessories
Gigaset Handsets
Upgrade your Gigaset to a cordless PABX:
Gigaset Handset C46
u
u
u
u
u
u
u
u
Illuminated colour display (4096 colours)
Various different screensavers
Illuminated keypad
Handsfree talking
Polyphonic ringer tones
Directory for around 100 entries
Alarm clock
Headset socket
www.siemens.com/gigaset
Gigaset Handset S45
u
u
u
u
u
u
u
Illuminated colour display (4096 colours)
Illuminated keypad
Handsfree talking
Polyphonic ringer tones
Directory for around 150 entries
Headset socket
Room monitor
www.siemens.com/gigaset
Version 2, 21.12.2006
All accessories and batteries are available from your phone retailer.
Only use original accessories. This will avoid possible health risks and damage to property, and also ensure that all the relevant regulations are complied with.
134
CE 450 IP R / IM-Ost english / A31008-M1817-R601_1-7619 / glossary.fm / 02.03.2007
Glossary
A
ADSL
Asymmetric Digital Subscriber Line
Special form of DSL.
ALG
Application Layer Gateway
NAT control mechanism of a router.
Many routers with integrated NAT use ALG. ALG lets the data packets in a VoIP connection pass and adds the public IP address of the secure private network.
The router's ALG should be deactivated if the VoIP provider offers a STUN server or an
outbound proxy.
See also: Firewall, NAT, Outbound proxy, STUN.
Authentication
Restriction of access to a network/service by use of an ID and password to log in.
Automatic ringback
See Ringback when the number is busy.
B
Broadband Internet access
See DSL.
C
Call forwarding
CF
Automatic forwarding of a call to a different telephone number. There are three kinds
of call forwarding:
– CFU, Call Forwarding Unconditional
– CFB, Call Forwarding Busy
– CFNR, Call Forwarding No Reply
Call waiting
CW
VoIP provider feature. A beep during a call indicates that another caller is waiting. You
can accept or reject the second call. You can activate/deactivate the feature.
CAT5 cable
Network cables in the category "CAT-5 cable" are nowadays the most-used base stations
that are being installed. They are used for signal transmission with high data transfer
rates. The specific standard description is EIA/TIA-568. Cat-5 cables are intended for
operating frequencies of up to 100 MHz.
CF
Version 2, 21.12.2006
Call Forwarding
See Call forwarding.
Client
Application that requests a service from a server.
135
CE 450 IP R / IM-Ost english / A31008-M1817-R601_1-7619 / glossary.fm / 02.03.2007
Codec
Coder/decoder
Codec is a procedure that digitises and compresses analogue voice before it is sent via
the Internet and decodes – i.e. translates into analogue voice – digital data when voice
packets are received. There are different codecs, with differing degrees of compression,
for instance.
Both parties involved in the telephone connection (caller/sender and recipient) must
use the same codec. This is negotiated between the sender and the recipient when
establishing a connection.
The choice of codec is a compromise between voice quality, transmission speed and the
necessary bandwidth. A high level of compression, for example, means that the bandwidth required for each voice connection is low. However, it also means that the time
needed to compress/decompress the data is greater, which increases execution time for
data in the network and thus impairs voice quality. The time required increases the delay
between the sender speaking and the recipient hearing what has been said.
Consultation call
You are on a call. With a consultation call, you interrupt the conversation briefly to
establish a connection to another participant. If you terminate the connection to this
participant immediately, then this was a consultation call. If you switch to and fro
between the first and second participants, it is called Toggling.
CW
Call Waiting
See Call waiting.
D
DHCP
Dynamic Host Configuration Protocol
Internet protocol which handles the automatic assignment of IP addresses to Network
subscribers. The protocol is made available in the network by a server. A DHCP server
can e.g. be a router.
The phone contains a DHCP client. A router that contains a DHCP server can assign the
IP addresses for the phone automatically from a defined address block. The dynamic
assignment means that several Network subscribers can share one IP address,
although they use it alternately and not simultaneously.
With some routers you can specify that the IP address for the phone is never changed.
Displayed name
VoIP provider feature. You can specify any name that is to be shown to the other party
call instead of your phone number.
DMZ
Version 2, 21.12.2006
Demilitarised Zone
DMZ describes a part of a network that is outside the firewall.
A DMZ is set up, as it were, between a network you want to protect (e.g. a LAN) and an
insecure network (e.g. the Internet). A DMZ permits unrestricted access from the Internet to only one or a few network components, while the other network components
remain secure behind the firewall.
136
CE 450 IP R / IM-Ost english / A31008-M1817-R601_1-7619 / glossary.fm / 02.03.2007
DNS
Domain Name System
Hierarchical system that permits the assignment of IP addresses to Domain names that
are easier to note. This assignment has to be managed by a local DNS server in each
(W)LAN. The local DNS server determines the IP address, if necessary by enquiring about
superordinate DNS servers and other local DNS servers on the Internet.
You can specify the IP address of the primary/secondary DNS server.
See also: DynDNS.
Domain name
Name of one (or several) Web server(s) on the Internet (e.g. Siemens-Home). The
domain name is assigned to the relevant IP address by DNS.
DSCP
Differentiated Service Code Point
See Quality of Service (QoS).
DSL
Digital Subscriber Line
Data transfer technology which allows Internet access at e.g. 1.5 Mbps over conventional phone lines. Preconditions: DSL modem and the appropriate service offered by
the Internet service provider.
DSLAM
Digital Subscriber Line Access Multiplexer
The DSLAM is a switch cabinet in an exchange at which all subscriber connectors converge.
DTMF
Dual Tone Multi-Frequency
Another description for dual tone multi-frequency dialling.
Dynamic IP Address
A dynamic IP address is assigned to a network component automatically via DHCP. The
dynamic IP address for a network component can change every time it registers or at
certain time intervals.
See also: Static IP address
DynDNS
Dynamic DNS
Domain names and IP addresses are realised via DNS. For Dynamic IP Addresses this
service is now enhanced with "Dynamic DNS" (DynDNS). This permits the use of a network component with a dynamic IP address as a Server on the Internet. DynDNS
ensures that a service can always be addressed on the Internet under the same Domain
name irrespective of the current IP address.
E
EEPROM
Version 2, 21.12.2006
Electrically Eraseable Programmable Read Only Memory
Your phone's storage chip with fixed data (e.g. user-specific device settings made at the
factory) and automatically saved data (e.g. calls list entries).
Ethernet network
Wired LAN.
137
CE 450 IP R / IM-Ost english / A31008-M1817-R601_1-7619 / glossary.fm / 02.03.2007
Exposed Host
Exposed host refers to a PC outside the firewall.
See also: DMZ
F
Firewall
You can use a firewall to protect your network against unauthorised external access.
This involves combining various measures and technologies (hard and/or software) to
control the flow of data between a private network you wish to protect and an unprotected network (e.g. the Internet).
See also: NAT.
Firmware
Device software in which basic information is saved for the functioning of a device. A
new version of the firmware can be loaded into the device's memory (firmware update)
to correct errors or update the device software.
Flat rate
System of billing for an Internet connection. The Internet service provider charges a set
monthly fee. There are no additional charges for the duration of the connection or
number of connections.
Fragmentation
Data packets that are too big are split into smaller packets (fragments) before they are
transferred. They are put together again when they reach the recipient (defragmented).
Full duplex
Data transmission mode in which data can be sent and received at the same time.
G
Version 2, 21.12.2006
G711 a law, G711 µ law
Standard for a Codec.
G711 delivers a very good voice quality that corresponds to that in the ISDN fixed network. As there is little compression, the necessary bandwidth is around 64 kbit/s per
voice connection, but the delay caused by coding/decoding is only 0.125 ms.
"a law" describes the European standard and "µ law" describes the North American/Japanese equivalent.
G726
Standard for a Codec.
G726 delivers a good voice quality. It is inferior to the quality with Codec G711 but better than with G729.
G729A/B
Standard for a Codec.
The voice quality is rather less with G729A/B. As a result of the high level of compression, the necessary bandwidth is only around 8 kbit/s per voice connection, but the
delay is around 15 ms.
138
CE 450 IP R / IM-Ost english / A31008-M1817-R601_1-7619 / glossary.fm / 02.03.2007
Gateway
Connects two different Networks with one another, e.g. router as Internet gateway.
For phone calls from VoIP to the telephone network, a gateway has to be connected to
the IP network and the telephone network (gateway/VoIP provider). It forwards calls
from VoIP to the telephone network as required.
Gateway Provider
See SIP provider.
Global IP Address
See IP address.
GSM
Global System for Mobile Communication
Originally, European standard for mobile networks. GSM can now be described as a
worldwide standard. In the USA and Japan national standards are now more frequently
supported than in the past.
H
Headset
Combination of microphone and headphone. A headset makes handsfree talking more
comfortable. There are headsets available which are connected to the handset by a
cable.
HTTP Proxy
Server via which the Network subscribers can process their Internet traffic.
Hub
Uses one Infrastructure network to connect several Network subscribers. All data
sent to the hub by one network subscriber is forwarded to all network subscribers.
See also: Gateway, Router.
I
IEEE
Version 2, 21.12.2006
Institute of Electrical and Electronics Engineers
International body that defines standards in electronics and electrotechnology, concerned in particular with the standardisation of LAN technology, transmission protocols,
data transfer rate and wiring.
Infrastructure network
Network with central structure: all Network subscribers communicate via a central
Router.
Internet
Global WAN. A series of protocols have been defined for exchanging data, known by the
name TCP/IP.
All Network subscribers can be identified by their IP addresses. DNS assigns a Domain
name to the IP address.
Important services on the Internet include the World Wide Web (WWW), e-mail, file
transfer and discussion forums.
Internet Service Provider
Enables access to the Internet for a fee.
139
CE 450 IP R / IM-Ost english / A31008-M1817-R601_1-7619 / glossary.fm / 02.03.2007
IP (Internet Protocol)
TCP/IP protocol on the Internet. IP is responsible for addressing parties in a Network
using IP addresses and routes data from the sender to the recipient. IP determines the
paths (routing) along which the data packets travel.
IP address
A unique address for a network component within a network on the basis of the TCP/IP
protocols (e.g. LAN, Internet). On the Internet, domain names are usually assigned
instead of IP addresses. DNS assigns the corresponding IP address to the domain name.
The IP address has four parts (decimal numbers between 0 and 255) separated by full
stops (e.g. 230.94.233.2).
The IP address is made up of the network number and the number of the Network subscribers (e.g. phone). Depending on the Subnet mask, the front one, two or three
parts make up the network number and the rest of the IP address addresses the network
component. The network number of all the components in any one network must be
identical.
IP addresses can be assigned automatically with DHCP (dynamic IP addresses) or manually (static IP addresses).
See also: DHCP.
IP pool range
Range of IP addresses that the DHCP server can use to assign dynamic IP addresses.
ISP
Internet Service Provider
See Internet Service Provider.
L
LAN
Local Area Network
Network with a restricted physical range. A LAN can be wireless (WLAN) and/or wired.
Local IP Address
The local or private IP address is the address for a network component in the local network (LAN). The network operator can assign any address he or she wants. Devices that
act as a link from a local network to the Internet (gateway or router) have a public and
a private IP address.
See also IP address.
Local SIP Port
See SIP port/Local SIP port.
M
MAC address
Version 2, 21.12.2006
Media Access Control Address
Hardware address by means of which each network device (e.g. network card, switch,
phone) can be uniquely identified worldwide. This consists of 6 parts (hexadecimal
numbers), which are separated by "-"(e.g. 00-90-65-44-00-3A).
The MAC address is assigned by the manufacturer and cannot be changed.
Mbps
Million bits per second
Unit of the transmission speed in a network.
140
CE 450 IP R / IM-Ost english / A31008-M1817-R601_1-7619 / glossary.fm / 02.03.2007
MRU
Maximum Receive Unit
Defines the maximum user data volume within a data packet.
MTU
Maximum Transmission Unit
Defines the maximum length of a data packet that can be carried over the network at a
time.
Music on hold
Music that is played while you are on a Consultation call or Toggling. The waiting participant hears music while on hold.
N
NAT
Network Address Translation
Method for converting (private) IP addresses to one or more (public) IP addresses.
NAT enables the IP addresses of Network subscribers (e.g. VoIP telephones) in a LAN
to be concealed behind a shared IP address for the Router on the Internet.
VoIP telephones behind a NAT router cannot be reached by VoIP servers (on account of
the private IP address). In order to "get around" NAT, it is possible to use (alternatively)
ALG in the router, STUN in the VoIP telephone, or for the VoIP provider to use an Outbound proxy.
If an outbound proxy is made available you must allow for this in the VoIP settings for
your phone.
Network
Group of devices. Devices can be connected in either wired or wireless mode.
Networks can also differ in range and structure:
– Range: local networks (LAN) or wide-area networks (WAN)
– Structure: Infrastructure network or ad-hoc network
Network subscribers
Devices and computers that are connected to each other in a network, e.g. servers, PCs
and phones.
O
Outbound proxy
Alternative NAT control mechanism to STUN and ALG.
Outbound proxies are implemented by the VoIP provider in firewall/NAT environments
as an alternative to SIP proxy server. They control data traffic through the firewall.
Outbound proxy and STUN servers should not be used simultaneously.
See also: STUN and NAT.
P
PIN
Version 2, 21.12.2006
Personal Identification Number
Protects against unauthorised use. When the PIN is activated a number combination has
to be entered in order to access a protected area.
You can protect your base station configuration data with a system PIN (4-digit number
combination).
141
CE 450 IP R / IM-Ost english / A31008-M1817-R601_1-7619 / glossary.fm / 02.03.2007
Port
Data is exchanged between two applications in a Network via a port.
Port Forwarding
The Internet gateway (e.g. your router) forwards data packets from the Internet that are
directed to a certain Port to the port concerned. This allows servers in the LAN to offer
services on the Internet without you needing a public IP address.
Port number
Indicates a specific application of Network subscribers. Depending on the setting in
the LAN, the port number is permanently assigned or else it is newly assigned with each
access.
The combination of IP address/Port number uniquely identifies the recipient or sender
of a data packet within a network.
PPPoE
Point-to-Point Protocol over Ethernet
Protocol for connecting network subscribers within an Ethernet network to the Internet via a modem.
PPTP
Point-to-Point Tunnelling Protocol
Protocol for setting up a virtual private network (Virtual Private Network VPN) via the
Internet. This allows the Point-to-Point protocol to tunnel through the IP network.
Private IP Address
See Public IP address.
Protocol
Describes the agreements for communicating within a Network. It contains rules for
opening, administering and closing a connection, about data formats, time frames and
possible error handling.
Proxy/Proxy server
Computer program that controls the exchange of data between Client and Server in
computer networks. If the phone sends a query to the VoIP server, the proxy acts as a
server towards the phone and as a client towards the server. A proxy is addressed via IP
address/Domain name and Port.
Public IP address
The public IP address is the address for a network component on the Internet. It is
assigned by the Internet service provider. Devices that act as a link from a local network
to the Internet (gateway or router) have a public and a local IP address.
See also: IP address, NAT
Version 2, 21.12.2006
Q
Quality of Service (QoS)
Describes the Quality of Service in communication networks. Differentiations are made
between various Quality of Service classes.
QoS influences the flow of data packets on the Internet e.g. by prioritising data packets,
bandwidth reservation and packet optimisation.
In VoIP networks, QoS influences the voice quality. If the whole infrastructure (router,
network server etc.) has QoS, the voice quality is better, i.e. fewer delays, less echoing,
less crackling.
142
CE 450 IP R / IM-Ost english / A31008-M1817-R601_1-7619 / glossary.fm / 02.03.2007
R
RAM
Random Access Memory
Memory in which you have reading and storage rights. Such items asmelodies and
screen pictures are stored in the RAM after being loaded into the phone via the Web configurator.
Registrar
The registrar manages the current IP addresses of Network subscribers. When you register with your VoIP provider, your current IP address is saved on the registrar. This
means you can also be reached when on the move.
Ringback when the call is not answered
= CCNR (Completion of calls on reply). If a participant does not respond when called, a
caller can arrange an automatic ringback. As soon as the destination phone has completed a call and is free again the caller is rung back. This feature must be supported by
the exchange. The ringback request is automatically cancelled after about 2 hours
(depending on the VoIP provider).
Ringback when the number is busy
= CCBS (Completion of Calls to Busy Subscriber). If a caller hears the busy tone, he or
she can activate the ringback function. As soon as the connection is free the caller is
rung back. As soon as the caller lifts his receiver the connection is made automatically.
RJ45 modular jack
Eight-pole (8P8C) modular jack. RJ stands for Registered Jack (standardised socket).
RJ45 is used for ISDN connection sockets and cables, structured wiring and computer
networks.
ROM
Read Only Memory
A type of memory that can only be read, as opposed to RAM which can be both read and
written.
Router
Routes data packets within a network and between different networks via the quickest
route. Can connect Ethernet networks and WLAN. Can be a Gateway to the Internet.
Routing
Routing is the transmission of data packets to another subscriber in your network. On
its way to the recipient, the data packet is sent from one router to the next until it
reaches its destination.
If data packets were not forwarded in this way, a network like the Internet would not be
possible. Routing connects the individual networks to this global system.
A router is a part of this system; it transmits data packets both within a local network
and from one network to the next. Transmission of data from one network to another is
performed on the basis of a common protocol.
RTP
Version 2, 21.12.2006
Realtime Transport Protocol
Global standard for transferring audio and video data. Often used in conjunction with
UDP. In this case, RTP packets are embedded in UDP packets.
RTP port
(Local) Port which is used to send and receive voice data packets for VoIP.
143
CE 450 IP R / IM-Ost english / A31008-M1817-R601_1-7619 / glossary.fm / 02.03.2007
S
Server
Provides a service to other Network subscribers (Clients). The term can indicate a computer/PC or an application. A server is addressed via IP address/Domain name and Port.
SIP (Session Initiation Protocol)
Signalling protocol independent of voice communication. Used for establishing and
ending a call. It is also possible to define parameters for voice transmission.
SIP address
See URI.
SIP port/Local SIP port
(Local) Port which is used to send and receive SIP signalling data for VoIP.
SIP provider
See VoIP provider.
SIP proxy server
IP address of your VoIP provider's gateway server.
Static IP address
A static IP address is assigned to a network component manually during network configuration. Unlike a Dynamic IP Address, a static (fixed) IP address never changes.
STUN
Simple Traversal of UDP over NAT
Version 2, 21.12.2006
NAT control mechanism.
STUN is a data protocol for VoIP telephones. STUN replaces the private IP address in the
data packets of the VoIP telephone with the public address of the secure private network. To control data transfer, a STUN server is also required on the Internet. STUN cannot be implemented with symmetric NATs.
See also: ALG, Firewall, NAT, Outbound proxy.
Subnet
Segment of a Network.
Subnet mask
IP addresses consist of a fixed network number and a variable subscriber number. The
network number is identical for all Network subscribers. The proportion of the IP
address made up of the network number is determined in the subnet mask. For the subnet mask 255.255.255.0, for example,the first three parts of the IP address are the network number and the last part is the subscriber number.
Switch
Connects different network elements (see also Hub). A switch forwards data packets
straight to the network subscriber to which they are addressed.
Symmetric NAT
A symmetric NAT assigns different external IP addresses and port numbers to the same
internal IP address and port number – depending on the external target address. Your
router has a symmetric NAT.
144
CE 450 IP R / IM-Ost english / A31008-M1817-R601_1-7619 / glossary.fm / 02.03.2007
T
TCP
Transmission Control Protocol
Transport protocol. Session-based transmission protocol: it sets up, monitors and terminates a connection between sender and recipient for transporting data.
TLS
Transport Layer Security
Protocol for encrypting data transmissions on the Internet. TLS is a superordinated
Transport protocol.
Toggling
Toggling allows you to switch between two callers or between a conference call and an
individual caller without allowing the waiting caller to listen in.
Transmission rate
Speed at which data is transmitted in the WAN or LAN. The transmission rate is measured in data units per unit of time (Mbit/s).
Transport protocol
Controls data transport between communication partners (applications).
See also: UDP, TCP, TLS.
U
UDP
User Datagram Protocol
Transport protocol. Unlike TCP, UDP is a non session-based protocol. It does not establish a fixed connection. The data packets (datagrams) are sent as broadcast. The recipient is solely responsible for making sure the data is received. The sender is not notified
about whether it is received.
UPnP
Universal Plug and Play
Enables spontaneous linking of networks: UPnP-compatible devices carry out the network configuration automatically when they log in to the network. The devices make
services available to the network and use the services of other devices in the network.
URI
Uniform Resource Identifier
Character string used to identify resources (e.g. e-mail recipient, http://siemens.com,
files).
On the Internet URIs are used as a uniform identification for resources. URIs are also
described as an SIP address.
URIs can be entered in the phone as a number. By dialling a URI you can call an Internet
subscriber with VoIP equipment.
URL
Version 2, 21.12.2006
Universal Resource Locator
Globally unique address of a domain on the Internet.
A URL is a subtype of URI. URLs identify a resource by its location on the Internet. For
historical reasons the term is often used as a synonym for URI.
User ID
See User identification.
145
CE 450 IP R / IM-Ost english / A31008-M1817-R601_1-7619 / glossary.fm / 02.03.2007
User identification
Name/number combination for access e.g. to your VoIP account.
V
Virtual private network (VPN)
Virtual Private Network
Computer network that uses a public network (e.g. the Internet) to transport private
data.
Virtual server
A virtual server provides a service on the Internet that does not run on itself, but on a
different network subscriber instead. External service requests are forwarded via Port
Forwarding straight to the appropriate Port for the relevant network subscriber in the
local network.
Voice codec
See Codec.
VoIP
Voice over Internet Protocol
Telephone calls are no longer placed and transmitted over the telephone network but
over the Internet (or other IP networks).
VoIP provider
A VoIP, SIP or Gateway Provider is an Internet service provider that provides a Gateway
for Internet telephony. As the phone works with the SIP standard, your provider must
support the SIP standard.
The provider routes calls from VoIP to the telephone network (analogue, ISDN and
mobile radio) and vice versa.
W
WAN
Wide Area Network
Version 2, 21.12.2006
Wide-area network that is unrestricted in terms of area (e.g Internet).
146
CE 450 IP R / IM-Ost english / A31008-M1817-R601_1-7619 / CE450IP_R_laenderSIX.fm / 02.03.2007
Index
Index
24 hours in advance (alarm clock) . . . 55
Auto answer . . . . . . . . . . . . . . . . 29, 53
Automatic area code
(de)activating . . . . . . . . . . . . . . . 103
Automatic log-off
phone Web configurator . . . . . . . . 86
router Web configurator . . . . . . . . . 82
Automatic versions check . . . . . . . . 107
Available codecs . . . . . . . . . . . . . . . . 98
A
B
Symbols
(Internet Service Provider) . . . . . . . . 140
Version 2, 21.12.2006
Numerics
Access from other networks
to phone Web configurator . . . . . . . 88
to router Web configurator . . . . . . . 82
Accessories . . . . . . . . . . . . . . . . . . . 134
Activating
advisory tones . . . . . . . . . . . . . . . . 54
Annex B for G729 . . . . . . . . . . . . . . 99
call acceptance . . . . . . . . . . . . . . . . 53
handset . . . . . . . . . . . . . . . . . . . . . . 1
handsfree talking . . . . . . . . . . . . . . 30
keypad lock . . . . . . . . . . . . . . . . . . 31
Activating/deactivating repeater
mode . . . . . . . . . . . . . . . . . . . . . 58
Address assignment (local IP address)
phone (on handset) . . . . . . . . . . . . 59
phone (Web config.) . . . . . . . . . . . . 87
router. . . . . . . . . . . . . . . . . . . . . . . 80
ADSL . . . . . . . . . . . . . . . . . . . . . . . . 135
Advisory tones . . . . . . . . . . . . . . . . . . 54
Alarm clock . . . . . . . . . . . . . . . . . . . . 55
setting . . . . . . . . . . . . . . . . . . . . . . 55
setting ringer tone . . . . . . . . . . . . . 54
snooze . . . . . . . . . . . . . . . . . . . . . . 55
Alarm repeat . . . . . . . . . . . . . . . . . . . 55
ALG . . . . . . . . . . . . . . . . . . . . . . . . . 135
Application Layer Gateway (ALG) . . . 135
Area code, dialling automatically . . . 103
Assigning sending number to
handset . . . . . . . . . . . . . . . . . . 100
Asymmetric Digital Subscriber Line . . 135
Attack detection . . . . . . . . . . . . . . . . . 74
Audio
advisory tones . . . . . . . . . . . . . . . . 54
battery warning tone . . . . . . . . . . . 54
changing ringer tone . . . . . . . . . . . 53
only permitting 1 VoIP call. . . . . . . . 97
optimising VoIP voice quality . . . . . . 97
settings for the bandwidth . . . . . . . 97
Authentication . . . . . . . . . . . . . . . . . 135
Authorisation . . . . . . . . . . . . . . . . . . 121
Backlight . . . . . . . . . . . . . . . . . . . . . 52
Bandwidth for VoIP connections. . . . . 79
Base station
changing system PIN . . . . . . . . . . . 56
checking service information . . . . 119
components . . . . . . . . . . . . . . . . . . 6
connecting . . . . . . . . . . . . . . . . . . 12
connecting with mains power
supply. . . . . . . . . . . . . . . . . . . 14
connecting with the DSL modem . . 13
LAN connection . . . . . . . . . . . . . . . 12
phone . . . . . . . . . . . . . . . . . . . . . . . 7
power consumption . . . . . . . . . . . 123
restoring to factory settings . . . . . . 56
router . . . . . . . . . . . . . . . . . . . . . . . 6
setting up . . . . . . . . . . . . . . . . . . . 11
Base station phone, see also Phone
Base station router, see also Router
Battery
charging . . . . . . . . . . . . . . . . . . . . 10
display . . . . . . . . . . . . . . . . . . . 1, 10
fitting . . . . . . . . . . . . . . . . . . . . . . . 8
icon . . . . . . . . . . . . . . . . . . . . . . . 10
recommended batteries . . . . . . . . 121
warning tone . . . . . . . . . . . . . . . . . 54
Belt clip . . . . . . . . . . . . . . . . . . . . . . 22
Broadband Internet access . . . . . . . . 135
Buttons (Web configurator) . . . . . . . . 68
C
Call
accepting . . . . . . . . . . . . . . . . . . .
disconnecting (toggling) . . . . . . . .
ending . . . . . . . . . . . . . . . . . . . . .
external . . . . . . . . . . . . . . . . . . . . .
internal . . . . . . . . . . . . . . . . . . . . .
making settings . . . . . . . . . . . . . . .
transferring (connect) . . . . . . . . . .
Call acceptance . . . . . . . . . . . . . . . . .
Call display . . . . . . . . . . . . . . . . . . . .
29
39
28
29
50
38
51
53
29
147
CE 450 IP R / IM-Ost english / A31008-M1817-R601_1-7619 / CE450IP_R_laenderSIX.fm / 02.03.2007
Version 2, 21.12.2006
Index
Call forwarding . . . . . . . . . . . . . . . . 135
(de)activating . . . . . . . . . . . . . . 38, 92
Call waiting . . . . . . . . . . . . . . . . . . . 135
accepting . . . . . . . . . . . . . . . . . . . . 39
activating/deactivating . . . . . . . . . . 38
internal call . . . . . . . . . . . . . . . . . . 51
Calling . . . . . . . . . . . . . . . . . . . . . . . . 28
entering IP address . . . . . . . . . . . . . 28
external . . . . . . . . . . . . . . . . . . . . . 28
from directory . . . . . . . . . . . . . . . . 41
Gigaset.net subscriber. . . . . . . . 35, 37
Calls list . . . . . . . . . . . . . . . . . . . . . . . 44
Cancelling
operation (handset) . . . . . . . . . . . . 33
operation (Web configurators) . . . . 68
Care of the telephone . . . . . . . . . . . 112
CF, see Call forwarding . . . . . . . . . . . 135
Characters
deleting . . . . . . . . . . . . . . . . . . . . . 33
special characters . . . . . . . . . . . . . 125
Charge status display . . . . . . . . . . . . . 10
Charging status (battery) . . . . . . . . 1, 10
Checking EEPROM version . . . . . . . . 108
Checking service information . . . . . . 119
Client . . . . . . . . . . . . . . . . . . . . . . . 135
Codec . . . . . . . . . . . . . . . . . . . . . . . 136
available codecs . . . . . . . . . . . . . . . 98
selecting . . . . . . . . . . . . . . . . . . . . 98
Colour scheme . . . . . . . . . . . . . . . . . . 52
Components
base station . . . . . . . . . . . . . . . . . . . 6
Configuration
base station via PC . . . . . . . . . . . . . 64
local network (router) . . . . . . . . . . . 80
Configuring
VoIP connection (handset) . . . . 17, 61
VoIP connection (Web config.). . . . . 89
Configuring access to Internet . . . 16, 71
Configuring Internet connection
(router) . . . . . . . . . . . . . . . . . . . . 16
Configuring the network mailbox . . . . 47
Confirmation tone . . . . . . . . . . . . . . . 54
Connecting PC with Web configurator . 65
phone . . . . . . . . . . . . . . . . . . . . . . 85
router. . . . . . . . . . . . . . . . . . . . . . . 69
Connecting the charging cradle . . . . . 10
Connecting the PC with the base
station . . . . . . . . . . . . . . . . . . . . 13
Connection
activating (VoIP) . . . . . . . . . . . . . . . 95
148
name . . . . . . . . . . . . . . . . . . . 89, 90
socket for headset . . . . . . . . . . . 1, 22
to Gigaset.net . . . . . . . . . . . . . . . . 96
to phone Web configurator . . . . . . 85
to router Web configurator . . . . . . . 69
Consultation call . . . . . . . . . . . . 39, 136
internal . . . . . . . . . . . . . . . . . . . . . 51
Contrast . . . . . . . . . . . . . . . . . . . . . . 52
Control key . . . . . . . . . . . . . . . . . . 1, 31
Correcting incorrect entries . . . . . . . . 33
Customer Care . . . . . . . . . . . . . . . . 120
CW, see Call waiting
D
Data packets, fragmentation . . . . . . 138
Data server for phone
firmware update . . . . . . . . . . . 106
Deactivating
advisory tones . . . . . . . . . . . . . . . . 54
call acceptance . . . . . . . . . . . . . . . 53
handset . . . . . . . . . . . . . . . . . . . . . . 1
handsfree talking . . . . . . . . . . . . . . 30
keypad lock . . . . . . . . . . . . . . . . . . 31
Defining dialling plans . . . . . . . . . . . 103
Defining preferred DNS server
phone . . . . . . . . . . . . . . . . . . . 61, 88
router . . . . . . . . . . . . . . . . . . . . . . 78
Demilitarised Zone . . . . . . . . . . . . . 136
De-registering
from Web configurator . . . . . . . . . . 65
handset from base station . . . . . . . 49
Describes . . . . . . . . . . . . . . . . . . . . 142
DHCP . . . . . . . . . . . . . . . . . . . . . . . 136
Dialling . . . . . . . . . . . . . . . . . . . . . . . 28
cancelling . . . . . . . . . . . . . . . . . . . 28
IP address . . . . . . . . . . . . . . . . . . . 28
with directory . . . . . . . . . . . . . . . . 41
with speed dial . . . . . . . . . . . . . . . 41
Differentiated Service Code Point . . . 137
Digital clock . . . . . . . . . . . . . . . . . . . 52
Digital Subscriber Line . . . . . . . . . . . 137
Access Multifier . . . . . . . . . . . . . . 137
Directory . . . . . . . . . . . . . . . . . . . . . 40
delete (on handset) . . . . . . . . . . . . 41
deleting (Web configurator) . . . . . 104
editing via PC. . . . . . . . . . . . . . . . 103
entry in tsv format, example. . . . . 105
file format on PC . . . . . . . . . . . . . 105
loading from PC . . . . . . . . . . . . . . 104
opening . . . . . . . . . . . . . . . . . 31, 32
CE 450 IP R / IM-Ost english / A31008-M1817-R601_1-7619 / CE450IP_R_laenderSIX.fm / 02.03.2007
Version 2, 21.12.2006
Index
order of entries . . . . . . . . . . . . . . . 124
saving entry . . . . . . . . . . . . . . . . . . 40
saving the first number . . . . . . . . . . 40
selecting entry . . . . . . . . . . . . . . . . 41
sending entry/list to handset . . . . . . 42
transferring to/from PC . . . . . . . . . 103
using to enter numbers . . . . . . . . . . 42
Display
backlight . . . . . . . . . . . . . . . . . . . . 52
calls list . . . . . . . . . . . . . . . . . . . . . 44
changing display language . . . . . . . 52
colour scheme . . . . . . . . . . . . . . . . 52
contrast . . . . . . . . . . . . . . . . . . . . . 52
in idle status . . . . . . . . . . . . . . . . . . . 1
missed calls . . . . . . . . . . . . . . . . . . 44
network mailbox message . . . . . . . . 47
screensaver . . . . . . . . . . . . . . . . . . 52
setting . . . . . . . . . . . . . . . . . . . . . . 52
Display keys . . . . . . . . . . . . . . . . . . 1, 32
Displayed name (VoIP) . . . . . . . . 91, 136
Displaying DHCP client (router) . . . . . . 81
Disposal
electrical and electronic devices. . . . . 4
DMZ . . . . . . . . . . . . . . . . . . . . . . . . 136
DNS. . . . . . . . . . . . . . . . . . . . . . . . . 137
Domain . . . . . . . . . . . . . . . . . . . . . . . 92
name . . . . . . . . . . . . . . . . . . . . . . 137
router. . . . . . . . . . . . . . . . . . . . . . . 81
Domain Name System . . . . . . . . . . . 137
Downloading
phone firmware . . . . . . . . . . . 58, 107
VoIP provider data. . . . . . . . 18, 61, 96
DSCP . . . . . . . . . . . . . . . . . . . . . . . . 137
DSL . . . . . . . . . . . . . . . . . . . . . . . . . 137
DSL modem . . . . . . . . . . . . . . . . . . . . 12
connecting with the base station . . . 13
DSLAM . . . . . . . . . . . . . . . . . . . . . . 137
DTMF . . . . . . . . . . . . . . . . . . . . . . . 137
reminder for VoIP . . . . . . . . . . . . . 101
Dynamic DNS . . . . . . . . . . . . . . . . . . 137
Dynamic Host Configuration
Protocol, see DHCP
Dynamic IP address . . . . . . . . . . . . . 137
defining address block (router) . . . . 80
phone . . . . . . . . . . . . . . . . . . . 60, 87
router. . . . . . . . . . . . . . . . . . . . . . . 71
DynDNS . . . . . . . . . . . . . . . . . . . . . . 137
E
Earpiece mode . . . . . . . . . . . . . . . . . . 30
Earpiece volume . . . . . . . . . . . . . . . . 53
E-mail
checking for notifications . . . . . . . 111
entering access data . . . . . . . . . . 111
registration name/password . . . . . 111
End call key. . . . . . . . . . . . . . . . . . 1, 28
Ending, call . . . . . . . . . . . . . . . . . . . . 28
Entering access data
e-mail . . . . . . . . . . . . . . . . . . . . . 111
Internet . . . . . . . . . . . . . . . . . . . . . 15
messenger. . . . . . . . . . . . . . . . . . 109
VoIP account . . . . . . . . . . . 17, 61, 91
Entering DNS server
phone . . . . . . . . . . . . . . . . . . . 61, 88
router . . . . . . . . . . . . . . . . . . . . . . 78
Entering VoIP user data
on handset . . . . . . . . . . . . . . . 19, 62
via phone Web configurator . . . . . . 91
Error tone . . . . . . . . . . . . . . . . . . . . . 54
Ethernet network . . . . . . . . . . . . . . 137
Exposed host . . . . . . . . . . . . . . . . . 138
setting up (router) . . . . . . . . . . . . . 77
External call . . . . . . . . . . . . . . . . . . . 28
F
Fast access
directory entries . . . . . . . . . . . . . . 41
network mailbox . . . . . . . . . . . . 1, 47
Firewall . . . . . . . . . . . . . . . . . . . . . 138
setting up (router) . . . . . . . . . . . . . 74
status . . . . . . . . . . . . . . . . . . . . . . 84
Firmware . . . . . . . . . . . . . . . . . . . . 138
Firmware update
automatic (phone) . . . . . . . . . 59, 107
defining server for update . . . . . . 106
from local PC (phone) . . . . . . . . . 106
starting for phone . . . . . . 58, 83, 107
Firmware version
checking for phone . . . . . . . . . . . 108
Flat rate . . . . . . . . . . . . . . . . . . . . . 138
Fragmentation of data packets. . . . . 138
Free software, licences . . . . . . . . . . 127
Full duplex . . . . . . . . . . . . . . . . . . . 138
G
G711 µ law . . . . . . . . . . . . . . . . . . . . 97
G711 a law . . . . . . . . . . . . . . . . . . . . 97
G726 . . . . . . . . . . . . . . . . . . . . . . . . 97
G729 . . . . . . . . . . . . . . . . . . . . . . . . 97
Gateway . . . . . . . . . . . . . . . . . . . . . 139
149
CE 450 IP R / IM-Ost english / A31008-M1817-R601_1-7619 / CE450IP_R_laenderSIX.fm / 02.03.2007
Index
Gateway provider . . . . . . . . . . . . . . . 139
Gigaset.net . . . . . . . . . . . . . . . . . 20, 34
(de)activating the connection . . . . . 96
calling subscriber . . . . . . . . . . . 35, 37
displaying number . . . . . . . . . . . . . 35
editing own name . . . . . . . . . . . . . 36
entering number in directory. . . . . . 36
entering own name . . . . . . . . . 20, 36
searching for subscriber . . . . . . . . . 34
Global IP address . . . . . . . . . . . . . . . 139
Global System for
Mobile Communication . . . . . . . 139
GNU Lesser General Public License . . 127
GSM . . . . . . . . . . . . . . . . . . . . . . . . 139
Version 2, 21.12.2006
H
Handset
activating/deactivating . . . . . . . . 1, 31
advisory tones . . . . . . . . . . . . . . . . 54
assigning receiving number. . . . . . 100
assigning sending number . . . . . . 100
changing internal names. . . . . . . . . 50
changing internal number . . . . . . . . 49
checking service information. . . . . 119
contact with liquid . . . . . . . . . . . . 112
de-registering . . . . . . . . . . . . . . . . . 49
display language . . . . . . . . . . . . . . . 52
idle status . . . . . . . . . . . . . . . . . . . 32
locating . . . . . . . . . . . . . . . . . . . . . 50
loudspeaker volume . . . . . . . . . 32, 53
muting . . . . . . . . . . . . . . . . . . . . . . 30
registering . . . . . . . . . . . . . . . . 11, 48
restoring to factory settings. . . . . . . 56
setting (individual) . . . . . . . . . . . . . 52
setting up . . . . . . . . . . . . . . . . . . . . . 8
transferring a call . . . . . . . . . . . . . . 51
using as an alarm clock . . . . . . . . . . 55
using several . . . . . . . . . . . . . . . . . 48
Handset directory, see Directory
Handsfree
activating/deactivating . . . . . . . . . . 30
key . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Hash key . . . . . . . . . . . . . . . . . . . . 1, 31
Headset . . . . . . . . . . . . . . . . . 1, 22, 139
Hearing aids . . . . . . . . . . . . . . . . . . . . 4
Hold music . . . . . . . . . . . . . 30, 57, 141
HTTP Proxy . . . . . . . . . . . . . . . . . . . 139
Hub . . . . . . . . . . . . . . . . . . . . . . 12, 139
150
I
Idle status
back to . . . . . . . . . . . . . . . . . . . . . 32
display . . . . . . . . . . . . . . . . . . . . . . 1
IEEE . . . . . . . . . . . . . . . . . . . . . . . . 139
Incoming e-mail server (e-mail) . . . . 111
Incorrect input (correction) . . . . . . . . 33
Infrastructure network . . . . . . . . . . 139
Initiating/ending multiparty . . . . . . . . 39
Installation, base station . . . . . . . . . . 11
Instant messaging . . . . . . . . . . . . . . 109
Institute of Electrical and
Electronics Engineers . . . . . . . . 139
Interface language
phone web configurator . . . . . . . 86
Internal
consulting . . . . . . . . . . . . . . . . . . . 51
making calls . . . . . . . . . . . . . . . . . 50
Internal call. . . . . . . . . . . . . . . . . . . . 50
call waiting . . . . . . . . . . . . . . . . . . 51
Internet . . . . . . . . . . . . . . . . . . . . . 139
Internet access (broadband) . . . . . . 135
Internet connection
configuring . . . . . . . . . . . . . . . . . . 71
entering access data . . . . . . . . 16, 71
Internet Protocol . . . . . . . . . . . . . . . 140
Internet Service Provider . . . . . . . . . 139
Introduction to VoIP . . . . . . . . . . . . . . 6
IP . . . . . . . . . . . . . . . . . . . . . . . 84, 140
IP address . . . . . . . . . . . . . . . . . . . . 140
assigning dynamically (router) . . . . 80
dynamic . . . . . . . . . . . . . . . . . . . 137
entering/dialling . . . . . . . . . . . . . . 28
global . . . . . . . . . . . . . . . . . . . . . 139
local . . . . . . . . . . . . . . . . . . . . . . 140
private . . . . . . . . . . . . . . . . . . . . 142
public . . . . . . . . . . . . . . . . . . . . . 142
static . . . . . . . . . . . . . . . . . . . . . . 144
structure . . . . . . . . . . . . . . . . . . . 140
IP address (phone)
assigning (on handset) . . . . . . . 59, 60
assigning (on Web config.) . . . 87, 108
obtaining automatically . . . . . . . . . 87
selecting address type . . . . . . . . . . 87
IP address (router)
checking public/global . . . . . . . . . . 84
defining local/private . . . . . . . . 80, 84
entering public/global . . . . . . . 72, 73
IP address block, router DHCP
CE 450 IP R / IM-Ost english / A31008-M1817-R601_1-7619 / CE450IP_R_laenderSIX.fm / 02.03.2007
Index
server . . . . . . . . . . . . . . . . . . . . . 80
IP filter, router firewall . . . . . . . . . . . . 74
IP pool range . . . . . . . . . . . . . . . . . . 140
IPUI . . . . . . . . . . . . . . . . . . . . . . . . . 119
ISP . . . . . . . . . . . . . . . . . . . . . . . . . 140
J
Jabber ID (messenger) . . . . . . . . . . . 110
Jabber server (messenger) . . . . . . . . 110
K
Key click . . . . . . . . . . . . . . . . . . . . . . 54
Keying in (instructions) . . . . . . . . . . 112
Keypad lock . . . . . . . . . . . . . . . . . . . . 31
Keys
assigning directory entry . . . . . . . . . 41
control key . . . . . . . . . . . . . . . . . 1, 31
display keys . . . . . . . . . . . . . . . . 1, 32
end call key . . . . . . . . . . . . . 1, 28, 33
handsfree key . . . . . . . . . . . . . . . . . . 1
hash key . . . . . . . . . . . . . . . . . . . 1, 31
keypad lock . . . . . . . . . . . . . . . . . . 31
message key . . . . . . . . . . . . . . . . 1, 44
on/off key . . . . . . . . . . . . . . . . . . . . . 1
paging key . . . . . . . . . . . . . . . . . . . . 1
speed dial. . . . . . . . . . . . . . . . . . . . 41
star key . . . . . . . . . . . . . . . . . . . 1, 54
talk key . . . . . . . . . . . . . . . . . . . . . . 1
Version 2, 21.12.2006
L
LAN . . . . . . . . . . . . . . . . . . . . . . . . . 140
configuring (router) . . . . . . . . . . . . 80
MAC address (router) . . . . . . . . . . . 84
Language
handset . . . . . . . . . . . . . . . . . . . . . 52
phone Web configurator . . . . . . . . . 86
Language Codec, see Codec
Last number redial . . . . . . . . . . . . . . . 43
LGPL . . . . . . . . . . . . . . . . . . . . . . . . 127
Licences, free software. . . . . . . . . . . 127
Liquid . . . . . . . . . . . . . . . . . . . . . . . 112
List
calls list . . . . . . . . . . . . . . . . . . . . . 44
entry . . . . . . . . . . . . . . . . . . . . . . . 45
last number redial list . . . . . . . . . . . 43
managing entries . . . . . . . . . . . 43, 46
missed calls . . . . . . . . . . . . . . . . . . 45
Local Area Network . . . . . . . . . . . . . 140
Local IP address . . . . . . . . . . . . . . . . 140
Local network . . . . . . . . . . . . . . . . . . 87
configuring (router) . . . . . . . . . . . . 80
Local SIP port . . . . . . . . . . . . . . . . . 144
Lock (keypad lock). . . . . . . . . . . . . . . 31
Login password
messenger. . . . . . . . . . . . . . . . . . 110
Loudspeaker volume . . . . . . . . . . 32, 53
M
MAC address . . . . . . . . . . . . . . . . . . 140
checking (handset) . . . . . . . . . . . . 63
checking (Web configurator) . . . . 108
LAN (router) . . . . . . . . . . . . . . . . . 84
WAN (router) . . . . . . . . . . . . . . . . . 84
MAC filter for the firewall (router) . . . 75
Mains adapter . . . . . . . . . . . . . . . . . . . 4
Making calls
accepting a call . . . . . . . . . . . . . . . 29
external . . . . . . . . . . . . . . . . . . . . . 28
internal . . . . . . . . . . . . . . . . . . . . . 50
via Gigaset.net . . . . . . . . . . . . . . . . 34
Maximum Receive Unit . . . . . . . . . . 141
Maximum Transmission Unit . . . . . . 141
Mbps . . . . . . . . . . . . . . . . . . . . . . . 140
Media Access Control . . . . . . . . . . . 140
Medical appliances . . . . . . . . . . . . . . . 4
Menu
end tone . . . . . . . . . . . . . . . . . . . . 54
going back one menu level . . . . . . . 33
menu guidance . . . . . . . . . . . . . . . 33
phone overview . . . . . . . . . . . . . . . 23
Web configurator overview . . . . . . 27
Menu bar
phone Web configurator . . . . . . . . 66
router Web configurator . . . . . . . . . 70
Message key . . . . . . . . . . . . . . . . . . . . 1
opening lists . . . . . . . . . . . . . . . . . 44
Messenger . . . . . . . . . . . . . . . . . . . 109
entering access data . . . . . . . . . . 109
resource name . . . . . . . . . . . . . . . 109
Million bits per second . . . . . . . . . . 140
Missed calls . . . . . . . . . . . . . . . . . . . 45
MRU . . . . . . . . . . . . . . . . . . . . . . . . 141
MTU . . . . . . . . . . . . . . . . . . . . . . . . 141
modifying value . . . . . . . . . . . . 72, 73
Music on hold . . . . . . . . . . . . . . . . . 141
Muting the handset. . . . . . . . . . . . . . 30
N
Name
changing name of the handset . . . . 50
151
CE 450 IP R / IM-Ost english / A31008-M1817-R601_1-7619 / CE450IP_R_laenderSIX.fm / 02.03.2007
Index
displayed (VoIP) . . . . . . . . . . . . . . 136
entering/editing for Gigaset.net . . . . 36
router. . . . . . . . . . . . . . . . . . . . . . . 81
NAT . . . . . . . . . . . . . . . . . . . . . . . . . 141
symmetric . . . . . . . . . . . . . . . . . . 144
updating (phone) . . . . . . . . . . . . . . 94
Navigation area
(Web configurator) . . . . . . . . . . . 67
Network . . . . . . . . . . . . . . . . . . . . . 141
Ethernet . . . . . . . . . . . . . . . . . . . . 137
Network Address Translation, see NAT
Network area . . . . . . . . . . . . . . . . . . . 93
Network mailbox
assigning key 1 . . . . . . . . . . . . . . . . 47
fast access . . . . . . . . . . . . . . . . . 1, 47
message . . . . . . . . . . . . . . . . . . . . . 47
Network services . . . . . . . . . . . . . . . . 38
accepting call waiting . . . . . . . . . . . 39
activating/deactivating call waiting . 38
call forwarding . . . . . . . . . . . . . . . . 38
consultation call . . . . . . . . . . . . . . . 39
multiparty . . . . . . . . . . . . . . . . . . . 39
settings during the call . . . . . . . . . . 39
settings for all calls . . . . . . . . . . . . . 38
toggling . . . . . . . . . . . . . . . . . . . . . 39
Number
copying from directory . . . . . . . . . . 42
display own Gigaset.net
subscriber . . . . . . . . . . . . . . . . 35
entering for the network mailbox . . 47
entering with directory . . . . . . . . . . 42
saving in the directory. . . . . 36, 40, 42
Number assignment . . . . . . . . . . . . . 100
Version 2, 21.12.2006
O
On/Off key . . . . . . . . . . . . . . . . . . . . . . 1
Online directory Gigaset.net . . . . . 20, 34
Only permitting 1 VoIP call . . . . . . . . . 97
Operation (preparing to use the
phone) . . . . . . . . . . . . . . . . . . . . . 8
Optimising VoIP voice quality . . . . . . . 97
Order in directory . . . . . . . . . . . . . . . 124
Outbound proxy. . . . . . . . . . . . . 95, 141
mode . . . . . . . . . . . . . . . . . . . . . . . 94
port . . . . . . . . . . . . . . . . . . . . . . . . 95
Outgoing transmission rate . . . . . 71, 78
Own codec preference . . . . . . . . . . . . 98
P
Pack contents . . . . . . . . . . . . . . . . . . . 8
152
Paging . . . . . . . . . . . . . . . . . . . . . 1, 50
Personal Identification Number,
see PIN
Personal provider data . . . . . . . . . . . . 91
Phone
(de)activating connection . . . . . . . 90
alternative DNS server . . . . . . . . . . 88
assigning IP address . . . . . . . . . 59, 87
assigning receiving numbers . . . . 100
assigning sending number . . . . . . 100
checking EEPROM version . . . . . . 108
checking firmware version . . . . . . 108
checking IP address . . . . . . . . 60, 108
checking MAC address . . . . . . 63, 108
configuring connections . . . . . . . . 89
configuring via PC . . . . . . . . . . . . . 64
defining dialling rules . . . . . . . . . 103
defining standard gateway . . . . . . . 87
DTMF reminder for VoIP . . . . . . . . 101
IP configuration . . . . . . . . . . . . . . . 87
making e-mail settings . . . . . . . . . 111
menu overview . . . . . . . . . . . . . . . 23
messenger access data . . . . . . . . . 109
name of a VoIP connection . . . . 89, 90
number assignment . . . . . . . . . . . 100
preferred DNS server . . . . . . . . . . . 88
resetting system PIN . . . . . . . . . . . 57
restoring to factory settings . . . . . . 56
selecting IP address type . . . . . . . . 87
setting (handset) . . . . . . . . . . . . . . 56
setting (Web configurator) . . . . . . . 85
status of a VoIP connection . . . . . . 89
subnet mask . . . . . . . . . . . . . . 60, 87
updating firmware . . . . . . . . . 58, 106
Phone IP configuration . . . . . . . . . . . 87
Phone status (Web configurator) . . . 108
Phone Web configurator . . . . . . . . . . 85
connecting with the PC . . . . . . . . . 85
directory transfer . . . . . . . . . . . . . 103
interface language . . . . . . . . . . . . . 86
phone status . . . . . . . . . . . . . . . . 108
remote management . . . . . . . . . . . 88
PIN . . . . . . . . . . . . . . . . . . . . . . . . . 141
changing . . . . . . . . . . . . . . . . . . . . 56
resetting . . . . . . . . . . . . . . . . . . . . 57
Point-to-Point Protocol over Ethernet,
see PPPoE
Point-to-Point Tunnelling Protocol,
see PPTP
Port . . . . . . . . . . . . . . . . . . . . . . . . 142
CE 450 IP R / IM-Ost english / A31008-M1817-R601_1-7619 / CE450IP_R_laenderSIX.fm / 02.03.2007
Index
Port Forwarding . . . . . . . . . . . . . . . . 142
router. . . . . . . . . . . . . . . . . . . . . . . 76
setting up (router) . . . . . . . . . . . . . 76
Port number . . . . . . . . . . . . . . . . . . 142
Power consumption (base station) . . 123
PPPoE . . . . . . . . . . . . . . . . . . . . 71, 142
PPTP . . . . . . . . . . . . . . . . . . . . . 71, 142
Priority (messenger) . . . . . . . . . . . . . 109
Private IP address . . . . . . . . . . . . . . . 142
defining (router) . . . . . . . . . . . . . . . 80
Problems and solutions . . . . . . . . . . 113
Protocol . . . . . . . . . . . . . . . . . . . . . . 142
Proxy . . . . . . . . . . . . . . . . . . . . . . . . 142
Proxy server . . . . . . . . . . . . . . . . . . . 142
Proxy server address . . . . . . . . . . . . . . 92
Public IP address . . . . . . . . . . . . . . . 142
Q
QoS, see Quality of Service
Quality of Service . . . . . . . . . . . . . . . 142
setting . . . . . . . . . . . . . . . . . . . . . . 78
settings for . . . . . . . . . . . . . . . . 16, 71
Questions and answers . . . . . . . . . . 113
Version 2, 21.12.2006
R
RAM . . . . . . . . . . . . . . . . . . . . . . . . 143
Random Access Memory . . . . . . . . . 143
Read Only Memory . . . . . . . . . . . . . 143
Rebooting the router . . . . . . . . . . . . . 83
Receiving number
assigning to handset . . . . . . . . . . . 100
display on the handset . . . . . . . . . . 29
Regional settings (router) . . . . . . . . . . 81
Registering
handset to base station . . . . . . . 11, 48
with the phone Web configurator . . 86
with the router Web configurator . . 69
Registrar . . . . . . . . . . . . . . . . . . . . . 143
Registrar server . . . . . . . . . . . . . . . . . 92
Registrar server port. . . . . . . . . . . . . . 92
Registration name
e-mail . . . . . . . . . . . . . . . . . . . . . 111
VoIP account . . . . . . . . . . . . . . . . . 91
Registration password
e-mail . . . . . . . . . . . . . . . . . . . . . 111
VoIP account . . . . . . . . . . . . . . . . . 91
Registration refresh time (VoIP) . . . . . 93
Remote management
phone . . . . . . . . . . . . . . . . . . . . . . 88
router. . . . . . . . . . . . . . . . . . . . . . . 82
Resource name (messenger) . . . . . . 109
Restoring to factory settings
base station . . . . . . . . . . . . . . . . . . 56
handset . . . . . . . . . . . . . . . . . . . . . 56
RFC 2833 . . . . . . . . . . . . . . . . . . . . 101
RFPI . . . . . . . . . . . . . . . . . . . . . . . . 119
Ringback
when busy . . . . . . . . . . . . . . . . . 143
when the call is not answered . . . 143
Ringer tone
activating/deactivating . . . . . . . . . . 54
changing . . . . . . . . . . . . . . . . . . . . 53
setting melody. . . . . . . . . . . . . . . . 54
setting volume . . . . . . . . . . . . 31, 53
RJ45 modular jack . . . . . . . . . . . . . . 143
ROM . . . . . . . . . . . . . . . . . . . . . . . . 143
Router . . . . . . . . . . . . . . . . . . . . . . 143
alternative DNS server . . . . . . . . . . 78
configuring local network . . . . . . . 80
defining local/private IP address . . . 80
name and domain . . . . . . . . . . . . . 81
private IP address . . . . . . . . . . . . . . 80
rebooting . . . . . . . . . . . . . . . . . . . 83
remote management . . . . . . . . . . . 82
resetting password. . . . . . . . . . . . . 57
restoring to factory settings . . . . . . 56
security log . . . . . . . . . . . . . . . . . . 83
setting (Web configurator) . . . . . . . 69
setting up firewall . . . . . . . . . . . . . 74
setting up NAT . . . . . . . . . . . . . . . . 75
specifying/editing password . . . . . . 82
status information . . . . . . . . . . . . . 84
updating firmware . . . . . . . . . . . . . 83
Router DHCP server
checking status . . . . . . . . . . . . . . . 84
configuring . . . . . . . . . . . . . . . . . . 80
Router firmware version
checking . . . . . . . . . . . . . . . . . . . . 84
Router gateway
checking . . . . . . . . . . . . . . . . . . . . 84
entering . . . . . . . . . . . . . . . . . 72, 73
Router LAN address . . . . . . . . . . . . . . 80
Router NAT
(de)activating . . . . . . . . . . . . . 75, 78
setting up . . . . . . . . . . . . . . . . . . . 75
setting up exposed host . . . . . . . . . 77
setting up port forwarding . . . . 76, 77
Router password
resetting . . . . . . . . . . . . . . . . . . . . 57
specifying/editing . . . . . . . . . . . . . 82
153
CE 450 IP R / IM-Ost english / A31008-M1817-R601_1-7619 / CE450IP_R_laenderSIX.fm / 02.03.2007
Index
Router Web configurator . . . . . . . . . . 69
connecting with the PC . . . . . . . . . . 69
Routing . . . . . . . . . . . . . . . . . . . . . . 143
setting (router) . . . . . . . . . . . . . . . . 79
table . . . . . . . . . . . . . . . . . . . . . . . 79
RTP . . . . . . . . . . . . . . . . . . . . . . . . . 143
RTP mode . . . . . . . . . . . . . . . . . . . . 101
RTP port . . . . . . . . . . . . . . . . . 102, 143
Version 2, 21.12.2006
S
Safety precautions . . . . . . . . . . . . . . . . 4
Screen protection, see Screensaver
Screensaver . . . . . . . . . . . . . . . . . . . . 52
Searching
handset . . . . . . . . . . . . . . . . . . . . . 50
in directory . . . . . . . . . . . . . . . . . . . 41
Security log (router) . . . . . . . . . . . . . . 83
Sending
directory entry to handset . . . . . . . . 42
Server . . . . . . . . . . . . . . . . . . . . . . . 144
for phone firmware update . . . . . . 106
Server port . . . . . . . . . . . . . . . . . . . . 92
Service . . . . . . . . . . . . . . . . . . . . . . 120
Setting
base station phone . . . . . . . . . . . . . 56
date/time . . . . . . . . . . . . . . . . . . . . 11
handset . . . . . . . . . . . . . . . . . . . . . 52
melody (ringer tone) . . . . . . . . . . . . 54
router. . . . . . . . . . . . . . . . . . . . . . . 69
wake up time . . . . . . . . . . . . . . . . . 55
Setting loudspeaker volume
handset language . . . . . . . . . . . 32, 53
Setting up port mapping (router) . . . . 77
Setting volume
earpiece . . . . . . . . . . . . . . . . . . . . . 53
for VoIP calls . . . . . . . . . . . . . . . . . . 98
loudspeaker . . . . . . . . . . . . . . . . . . 53
ringer tone . . . . . . . . . . . . . . . . . . . 53
Settings for VoIP telephony . . . 17, 59, 90
Shortcut (digit combination) . . . . . . . 23
Signal strength . . . . . . . . . . . . . . . . . . 1
Simple Traversal of UDP over NAT . . . 144
SIP . . . . . . . . . . . . . . . . . . . . . . . . . 144
SIP address . . . . . . . . . . . . . . . . . . . 144
SIP Info . . . . . . . . . . . . . . . . . . . . . . 101
SIP port . . . . . . . . . . . . . . . . . . 102, 144
SIP provider . . . . . . . . . . . . . . . . . . . 144
SIP proxy server . . . . . . . . . . . . . . . . 144
Snooze (alarm clock) . . . . . . . . . . . . . 55
Special characters . . . . . . . . . . . . . . 125
154
Specifications . . . . . . . . . . . . . . . . . 121
Speed dial. . . . . . . . . . . . . . . . . . . . . 41
Standard gateway (phone)
entering (handset) . . . . . . . . . . . . . 61
entering (Web configurator) . . . . . . 87
Star key . . . . . . . . . . . . . . . . . . . . 1, 54
Starting the connection
assistant. . . . . . . . . . . . . . . . 18, 61
Static IP address . . . . . . . . . . . . . . . 144
phone . . . . . . . . . . . . . . . . . . . 60, 87
router . . . . . . . . . . . . . . . . . . . . . . 71
Status
firewall . . . . . . . . . . . . . . . . . . . . . 84
router . . . . . . . . . . . . . . . . . . . . . . 84
router DHCP server . . . . . . . . . . . . 84
VoIP connection . . . . . . . . . . . . . . . 89
Status codes (VoIP)
activating display (handset) . . . . . . 63
activating display (Web config.) . . 107
table . . . . . . . . . . . . . . . . . . . . . . 116
Structure of IP address . . . . . . . . . . . 140
STUN . . . . . . . . . . . . . . . . . . . . . . . 144
STUN port . . . . . . . . . . . . . . . . . . . . . 94
STUN refresh time . . . . . . . . . . . . . . . 94
STUN server . . . . . . . . . . . . . . . . . . . 94
Subnet . . . . . . . . . . . . . . . . . . . . . . 144
Subnet mask . . . . . . . . . . . . . . . . . . 144
defining (phone) . . . . . . . . . . . 60, 87
defining (router) . . . . . . . . . . . . . . 80
Suppressing silence . . . . . . . . . . . . . . 99
Suppressing speech pauses . . . . . . . . 99
Suppressing speech pauses (VoIP) . . . 99
Switch . . . . . . . . . . . . . . . . . . . 12, 144
Switching off
call forwarding . . . . . . . . . . . . 38, 92
NAT . . . . . . . . . . . . . . . . . . . . . . . . 75
ringer tone . . . . . . . . . . . . . . . . . . 54
Switching on
call forwarding . . . . . . . . . . . . 38, 92
NAT . . . . . . . . . . . . . . . . . . . . . . . . 75
ringer tone . . . . . . . . . . . . . . . . . . 54
Symbols (instructions) . . . . . . . . . . . 112
Symmetric NAT . . . . . . . . . . . . . . . . 144
System PIN
changing . . . . . . . . . . . . . . . . . . . . 56
resetting . . . . . . . . . . . . . . . . . . . . 57
T
Talk key . . . . . . . . . . . . . . . . . . . . . . . 1
TCP. . . . . . . . . . . . . . . . . . . . . . . . . 145
CE 450 IP R / IM-Ost english / A31008-M1817-R601_1-7619 / CE450IP_R_laenderSIX.fm / 02.03.2007
Index
TLS . . . . . . . . . . . . . . . . . . . . . . . . . 145
Toggling . . . . . . . . . . . . . . . . . . 39, 145
Transferring PC address book
to directory . . . . . . . . . . . . . . . . 103
Transmission Control Protocol . . . . . . 145
Transmission rate . . . . . . . . . . . . . . . 145
Transport Layer Security . . . . . . . . . . 145
Transport protocol.. . . . . . . . . . . . . . 145
Troubleshooting . . . . . . . . . . . . . . . . 113
no Internet/VoIP connection . . . . . . 21
tsv file . . . . . . . . . . . . . . . . . . . . . . . 103
Turning off the microphone . . . . . . . . 30
U
UDP . . . . . . . . . . . . . . . . . . . . . . . . . 145
Uniform Resource Identifier . . . . . . . 145
Universal Plug and Play, see UPnP
Universal Resource Locator . . . . . . . . 145
Upload stream rate . . . . . . . . . . . . . . 79
UPnP . . . . . . . . . . . . . . . . . . . . . . . . 145
(de)activating (router) . . . . . . . . . . 78
URI . . . . . . . . . . . . . . . . . . . . . . . . . 145
URL . . . . . . . . . . . . . . . . . . . . . . . . . 145
Use random ports . . . . . . . . . . . . . . 102
User Datagram Protocol . . . . . . . . . . 145
User ID . . . . . . . . . . . . . . . . . . . . . . 145
User identification . . . . . . . . . . . . . . 146
User name (VoIP account) . . . . . . . . . 91
Version 2, 21.12.2006
V
Versions check, automatic . . . . . . . . 107
Viewing the network mailbox
message. . . . . . . . . . . . . . . . . . . 47
Virtual Private Network . . . . . . . . . . 146
Voice over Internet Protocol . . . . . . . 146
Voice quality
influence of the infrastructure . . . . . 99
only permitting 1 VoIP call. . . . . . . . 97
VoIP telephony . . . . . . . . . . . . . . . . 97
VoIP . . . . . . . . . . . . . . . . . . . . . . . . 146
configuring account . . . . . . 17, 61, 90
connection name . . . . . . . . . . . . . . 90
introduction . . . . . . . . . . . . . . . . . . . 6
loading provider data . . . . . 18, 61, 96
making calls via . . . . . . . . . . . . . . . 28
phone number . . . . . . . . . . . . . 19, 90
preconditions . . . . . . . . . . . . . . . . . . 6
VoIP calls, volume . . . . . . . . . . . . . . . 98
VoIP connection
(de)activating . . . . . . . . . . . . . . 90, 95
configuring (on handset) . . . . . . . . 59
configuring (Web config.) . . . . . . . 90
name . . . . . . . . . . . . . . . . . . . 89, 90
optimum bandwidth . . . . . . . . . . . 79
VoIP provider . . . . . . . . . . . . . . . . . 146
downloading data . . . . . . . 18, 61, 96
selecting . . . . . . . . . . . . . . . . . . . . 91
updating data automatically . . . . . 107
VoIP settings
downloading provider data . . . 18, 61
making them on the handset . . . . . 59
with connection assistant . . . . . 18, 61
without connection assistant . . . . . 61
VoIP status codes, table . . . . . . . . . . 116
VoIP status messages
activating display (handset) . . . . . . 63
activating display (Web config.) . . 107
status codes table . . . . . . . . . . . . 116
VoIP telephony
settings (on handset) . . . . . . . . 17, 59
settings (Web config.) . . . . . . . . . . 90
VPN . . . . . . . . . . . . . . . . . . . . . . . . 146
VPN server (PPTP) . . . . . . . . . . . . . . . 73
W
WAN . . . . . . . . . . . . . . . . . . . . . . . . 146
configuring connection . . . . . . 16, 71
connection type . . . . . . . . . . . . 71, 84
MAC address (router) . . . . . . . . . . . 84
Warning tone (battery) . . . . . . . . . . . 54
Web configurator . . . . . . . . . . . . . . . 64
connecting with PC . . . . . . . . . . . . 65
de-registering . . . . . . . . . . . . . . . . 65
menu overview . . . . . . . . . . . . . . . 27
opening Web page . . . . . . . . . . . . . 68
phone . . . . . . . . . . . . . . . . . . . . . . 85
router . . . . . . . . . . . . . . . . . . . . . . 69
structure of the web pages . . . . . . . 66
Web page (Web configurator)
opening . . . . . . . . . . . . . . . . . . . . 68
structure . . . . . . . . . . . . . . . . . . . . 66
Wide Area Network, see WAN
Working area (Web configurator) . . . . 67
Writing, editing text . . . . . . . . . . . . 124
155
Version 2, 21.12.2006
CE 450 IP R / IM-Ost english / A31008-M1817-R601_1-7619 / montage_charger_base.fm / 02.03.2007
156
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising