Kuryakyn 6911 Accessory User manual
Advertisement
Advertisement
INSTALLATION
TRI LINE ACCENT for SIDE TOUR PAK™ LIGHT 6911
THANK YOU FOR CHOOSING K ϋ RYAKYN!
PROTECT YOURSELF AND OTHERS FROM POSSIBLE INJURY AND PROPERTY
DAMAGE OR LOSS. PAY CLOSE ATTENTION TO ALL INSTRUCTIONS, WARNINGS,
CAUTIONS, AND NOTICES REGARDING THE INSTALLATION, USE, AND CARE OF
THIS PRODUCT.
THIS INDICATION ALERTS YOU TO THE FACT THAT
IGNORING THE CONTENTS DESCRIBED HEREIN CAN
RESULT IN POTENTIAL DEATH OR SERIOUS INJURY.
This indication alerts you to the fact that ignoring
the contents described herein can result in minor or moderate potential injury.
This indication alerts you to the fact that ignoring the
contents described herein may negatively affect product
performance and functionality or damage the product itself or the product to which it is being attached.
MAKE SURE THE FOLLOWING PARTS HAVE BEEN INCLUDED IN THE KIT:
Accent
1 Left
Pads
1 Installation
YOU WILL ALSO NEED:
Warm, soapy water and a clean rag, masking/painter’s tape
These installation instructions contain important information.
Ensure that the end user receives this copy and is aware of its importance for future reference.
STEP 1
STEP 2
Read and understand all steps in the instructions before starting the installation. Park the motorcycle on a hard, level surface and turn IGN OFF. to from the installation areas; allow the areas to dry completely.
PIC 1
CLEAN + DRY BOTH SIDES
Avoid damage to the motorcycle. Protect painted surfaces with a soft cloth or blanket.
CUSTOMER SERVICE
877.370.3604 (toll free)
INSTALLATION QUESTIONS [email protected] or call 715.247.2983
LIMITED WARRANTY
Küryakyn warrants that any Küryakyn products sold hereunder, shall be free of defects in materials and workmanship for a period of one
(1) year from the date of purchase by the consumer excepting the following provisions:
● Küryakyn shall have no obligation in the event the customer is unable to provide a receipt showing the date the customer purchased the product(s).
● The product must be properly installed, maintained and operated under normal conditions.
● Küryakyn makes no warranty, expressed or implied, with respect to any gold plated products.
● Küryakyn shall not be liable for any consequential and incidental damages, including labor and paint, resulting from failure of a
Küryakyn product, failure to deliver, delay in delivery, delivery in nonconforming condition, or for any breech of contract or duty between
Küryakyn and a customer.
● Küryakyn products are often intended for use in specific applications. Küryakyn makes no warranty if a Küryakyn product is used in applications other than intended.
● Küryakyn electrical products are warranted for one (1) year from the date of purchase by the consumer. L.E.D.’S contained in components of
Küryakyn products will be warranted for defects in materials and workmanship for 3 years from the date of purchase where as all other components shall be warranted for one(1) year.
This includes, but is not limited to; control modules, wiring, chrome & other components.
● Küryakyn makes no warranty of any kind in regard to other manufacturer¹s products distributed by Küryakyn. Küryakyn will pass on all warranties made by the manufacturer and where possible, will expedite the claim on behalf of the customer, but ultimately, responsibility for disposition of the warranty claim lies with the manufacturer.
ABOUT OUR CATALOG
For purchasing Küryakyn® products, you can receive a complete catalog free of charge.
Send the Proof-of-Purchase below with your address to: Küryakyn
454 County Road V V
Somerset, WI 54025-9031
Please indicate either Accessories Catalog for
Harley-Davidson® or GL & Metric Cruisers.
Be sure to ask your local dealer about other
Küryakyn® products, the motorcycle parts and accessories designed for riders by riders.
©2005 Küryakyn USA® All Rights reserved.
6911-21HD-0515 -cont.-
Ensure proper adhesion of this product. Remove all grease, oil, bugs, dirt, and other debris (including wax and polish) from the installation area. Kuryakyn will not provide warranty coverage on products or components lost or damaged due to improper installation.
Do not attempt this installation in temperatures below 50°F (10°C). Proper adhesive bonding ONLY occurs above 50°F (10°C).
STEP 3 Refer shown.
STEP 4 Wipe the installation areas with the included alcohol pads; allow the areas to dry completely.
STEP 5
PIC 2
TEST FIT THE ACCENT
CLUTCH-SIDE (LEFT)
PRESS INTO PLACE FOR 60 SEC.
Use your fingernail to rub the adhesive backing on the backside of the Left Accent; this will activate the adhesive. Remove and discard the backing.
STEP 6 Align the Accent and press it into place for one minute; full bonding will occur after 24 hours. Remove and discard the masking tape.
STEP 7 Repeat for the Right Accent.
Ride On!
TRI LINE ACCENT for SIDE TOUR PAK™ LIGHT
PAGE
2
INSTALLATION

Public link updated
The public link to your chat has been updated.
Advertisement