Sub Zero Design Guide

Sub Zero Design Guide
SUB-ZERO DESIGN GUIDE
CONTENTS
Built-In Refrigeration
4
Integrated Refrigeration
31
Wine Storage
50
Undercounter Refrigeration
67
Warranty
77
Features and specifications indicated
herein and on our website are subject
to change at any time without notice.
Check our website, subzero.com, for
the most up-to-date specifications.
SUB-ZERO ® is a registered trademark of Sub-Zero, Inc.
SUB-ZERO DESIGN GUIDE
WELCOME TO SUB-ZERO
We make the ultimate built-in, integrated and
undercounter refrigerators, freezers and wine
storage units. We offer more solutions to your
daily design problems of trying to work the
largest appliance into a home without being
obtrusive. Placing refrigeration in the home is no
longer a problem, but, rather, an opportunity to
exercise your creativity.
CONTACT
I N F O R M AT I O N
Sub-Zero has rethought traditional built-in
refrigeration, a category it pioneered, with over
60 years of experience. When our complete line
of configurations—all refrigerator and all freezer,
over-and-under, or side-by-side—are coupled
with three design alternatives and classic,
platinum and carbon stainless steel finishes, the
result is unlimited flexibility in satisfying your
client‘s needs for residential refrigeration.
Sub-Zero Customer
Service:
800-222-7820
Website:
subzero.com
Created to blend invisibly into your home‘s
decor, the Integrated line lets you incorporate
refrigeration anywhere in the house—the kitchen,
master suite, media room or workout room.
These tall units or two-drawer base refrigerators,
freezers and combination units can be hidden
inside the furniture or cabinetry of your
choosing.
Sub-Zero is breaking with conventional ways of
offering Wine Storage for designers and their
clients. Our Built-In and Integrated models, along
with the free-standing Model 424FS, offer unlimited design and storage capabilities.
Our reputation is legendary. We have engineered
and manufactured the best products in the
business, and we stand behind our products
with an unsurpassed warranty and a network of
technicians to help you if service is necessary.
See details of our warranty at the end of this
guide.
Comprehensive installation instructions are
shipped with each model. Refer to those
instructions in preparing and installing all
Sub-Zero products. These instructions along
with product specifications and downloadable
2D and 3D CAD files, as well as pdf files can be
found on our website, subzero.com.
IMPORTANT NOTE
As you follow these instructions, you
will notice warning and caution symbols.
This blocked information is important
for the safe and efficient installation of
Sub-Zero equipment. There are two
types of potential hazards that may
occur during installation.
signals a situation where minor
injury or product damage may occur
if you do not follow instructions.
states a hazard that may cause
serious injury or death if precautions
are not followed.
Another footnote we would like to
identify is IMPORTANT NOTE: This
highlights information that is especially
relevant to a problem-free installation.
3
B U I LT- I N R E F R I G E R AT I O N
B U I LT- I N R E F R I G E R AT I O N
Sub-Zero’s Built-In line offers you the most
complete set of design options in built-in refrigeration for all of its models, from the classic look
of the framed unit to the beauty of the overlay
models and the professional treatment of the
wrapped stainless steel doors.
Aside from the classic stainless steel, Sub-Zero
offers platinum and carbon premium stainless
steel finishes on its Built-In models and many
related accessories. The only exception to these
design alternatives are Models 648PRO and
648PROG, which are offered only in the classic
stainless steel design application. In addition,
Models 685 and 695 are offered in framed,
overlay and classic stainless steel (not platinum
or carbon).
Model 695/F
Framed
Glass doors are available on our Models 601R,
611 and 650. They each come in a framed,
overlay and stainless steel design. They all meet
stringent Department of Energy standards.
Model 648PROG also features a glass door in its
classic stainless steel look.
In the illustrations, we have shown the three
different design configurations of the framed,
overlay and stainless steel units applied to
Model 695. Please note how we qualify the
different looks with the model number.
Model 695/O
Overlay
Model 695/S
Classic
Stainless Steel
Dimensions in
parentheses are in
millimeters unless
otherwise specified.
4
The traditional framed units come with an
elegant full-length handle and an 11" (279)
louvered grille.
Overlay models will come with no handle
hardware, because the beauty of this design is
that you can match the surrounding cabinetry
hardware; however, we do offer optional handles
as sales accessories. The new ice and water
dispensing Models 685 and 695 are able to
accept overlay panels. Overlay models will come
with a standard 11" (279) panel grille that will
accept decorative panel inserts. Models 601R,
601RG and 601F are only available with the
louvered grille. No panel grille option is available.
All stainless steel models, with the exception of
those mentioned earlier, are offered in the classic
stainless steel finish and in the premium finishes
of platinum and carbon. Stainless steel models
come with a standard 11" (279) heavy-duty
grille, 1" (25) diameter stainless steel handles
and a stainless steel kickplate.
All grilles will be offered as options in 1" (25)
increments from 10" (254) to 15" (381) and can
be ordered as sales accessories. Models 601R,
601RG, 601F, 648PRO and 648PROG are the
exception and are available only with an 11"
(279) grille.
An important step in assuring a successful plan
is to make sure that the actual equipment
shipped to your installation site matches the
design you have ordered. Each of these three
design options—framed, overlay and stainless
steel—has specific installation requirements,
which means it is vital that the unit match your
planning and space needs.
B U I LT- I N R E F R I G E R AT I O N
B U I LT- I N R E F R I G E R AT I O N
A L L R E F R I G E R AT O R | A L L F R E E Z E R
These illustrations represent the full line of
Sub-Zero Built-In models shown in the stainless steel design application with heavy-duty
grille. Models 648PRO and 648PROG are
available as built-in or free-standing units in
classic stainless steel only.
36"
36"
36"
(914)
(914)
(914)
73"
73"
73"
(1854)
(1854)
(1854)
For information regarding specific Built-In
models, refer to the illustrations in this
section. Regardless of the specific design
application, framed, overlay or stainless steel,
the interior specifications of each model are
identical.
MODEL 601R
MODEL 601RG
MODEL 601F
All Refrigerator
All Refrigerator
with Glass Door
All Freezer
Energy Star
Qualified
Energy Star
Qualified
OVER-AND-UNDER
With the installation of a harness kit,
these appliances are Star-K compliant
to meet strict religious regulations in
conjunction with specific instructions
found on www.star-k.org. Models
648PRO and 648PROG are Star-K
certified from the factory with no extra
wiring harness required. For details
about the harness kit, contact your
Sub-Zero dealer.
30"
30"
36"
36"
(762)
(762)
(914)
(914)
84"
84"
84"
84"
(2134)
(2134)
(2134)
(2134)
MODEL 611
MODEL 611G
MODEL 650
MODEL 650G
Energy Star
Qualified
with Glass Door
Energy Star
Qualified
with Glass Door
S I D E - B Y- S I D E
36"
42"
42"
48"
48"
48"
48"
(914)
(1067)
(1067)
(1219)
(1219)
(1219)
(1219)
84"
84"
84"
84"
84"
84"
84"
(2134)
(2134)
(2134)
(2134)
(2134)
(2134)
(2134)
MODEL 661
MODEL 642
MODEL 685
Ice | Water
Dispensing
MODEL 632
MODEL 695
MODEL 648PRO
MODEL 648PROG
Ice | Water
Dispensing
Free-Standing
or Built-In
Free-Standing
or Built-In
Comprehensive installation instructions are
shipped with each model. Refer to those
instructions in preparing and installing all
Sub-Zero products. The instructions can also
be found on our website, subzero.com.
5
B U I LT- I N R E F R I G E R AT I O N
B U I LT- I N F E AT U R E S
Framed models—the classic look that made
Sub-Zero famous—feature a louvered grille and
elegant full-length handle. An optional panel grille
is available for framed units, except for Models
601R, 601RG and 601F. Optional panel conversion kits are available for the new ice and water
dispensing Models 685 and 695.
SUB-ZERO
WARRANTY
Sub-Zero products
are covered by a
two, five and twelve
year residential
warranty (exclusions
apply). See warranty
details at the end of
this guide.
Overlay models blend seamlessly into your
overall room design and complement surrounding
cabinetry. You add decorative hardware. Overlay
models come with a panel grille that will accept
decorative panel inserts. The new ice and water
dispensing Models 685 and 695 are also available in the overlay application.
Stainless steel models feature wrapped doors,
1" (25) diameter stainless steel handles and a
heavy-duty grille designed specifically to enhance
the aesthetics of today's professional looking
kitchens. All Built-In stainless steel models are
offered in the classic stainless steel finish and in
the premium finishes of platinum and carbon,
except for Models 685, 695, 648PRO and
648PROG, which are offered in classic stainless
steel only. The premium finishes are treated as
special orders and must be ordered 90 days
before you expect delivery.
Dual Refrigeration System. All Built-In combination models have the Sub-Zero dual refrigeration
system, which ensures the freshest food and
energy efficiency at the same time. You have
precise independent control of the refrigerator
and freezer compartments. In addition to two
compressors, the PRO 48 has three separate
evaporators to keep foods fresher longer and
prevent odor transfer.
Glass Door. Model 601RG is an all refrigerator
unit featuring a glass door. Models 611G and
650G are over-and-under combination units with
a glass door on the refrigerator. These glass door
models come in framed, overlay and stainless
steel designs and meet stringent Department of
Energy standards. The side-by-side Model
648PROG features a glass door on the refrigerator side and comes in classic stainless steel only.
Dimensions in
parentheses are in
millimeters unless
otherwise specified.
6
Fresh Food. High-humidity crisper drawer with
removable dividers is large and deep, with
smooth sides for easy cleaning. The top refrigerated drawer on the PRO 48 features a tight-seal,
retracting glass crisper lid that keeps produce
exceptionally humid and fresh.
Electronic Controls. Up-front touch controls
give you digital readings for quick, easy-to-read
reference. The microprocessor provides supreme
control, accurate to within one degree of preset
temperatures, automatic defrosting that senses,
then adapts to your use patterns, and a service
indicator light. The PRO 48 also features exterior
temperature displays.
Advanced Lighting. Bright lighting spreads
even illumination throughout the compartment.
The source of the illumination is concealed. The
PRO 48 top LED lights bathe upper compartments in a soft glow. On the refrigerator side,
channeled sidewall LEDs can even serve as a
door-area night-light for Model 648PROG.
Adjustable Shelves. Cantilevered glass shelves
make repositioning quick and easy. They are easy
to clean, spill proof and steel reinforced for durability. The PRO 48 features glass shelves with
stainless steel trim in the refrigerator and 100%
stainless steel shelves in the freezer.
Slide-Out Bins. An exclusive PRO 48 feature—
these versatile stainless steel bins hold small
items, remove easily, and fit neatly under any
shelf.
Door Shelves. All door shelves are adjustable for
complete flexibility and convenience.
Dairy Storage. Dairy compartment is adjustable,
with easy, one-door access, compartment
dividers and a clean design. The dairy shelf is
magnetically sealed to maintain freshness.
Automatic Ice. Ice maker provides high-quality,
crescent-shaped ice that won‘t stick to the side
of the glass. The PRO 48 features a water filter
located just behind the easy-access pop-up grille,
for ice as pure as it is fresh.
Stainless Steel. The PRO 48 (Models 648PRO
and 648PROG) feature stainless steel construction inside and out with classic finish for
professional strength and beauty.
Energy Efficient. Our solid core doors improve
insulation and structural integrity and help us
exceed tough Department of Energy standards.
Magnetic gaskets around all doors give extratight seals.
Ice and Water Dispensing. Models 685 and 695
feature a dispenser that gives you both ice and
chilled water through the refrigerator door.
Kickplate. Solid, adjustable kickplate gives a true
built-in look and conforms to American Institute
of Architects standards.
Built-In Design. True cabinet depth design means
every inch of the interior is easy to reach. The
PRO 48 can be built in or, with the free-standing
accessory kit, used in a free-standing application.
B U I LT- I N R E F R I G E R AT I O N
MODEL 601R
MODEL 601RG
MODEL 601F
A L L R E F R I G E R AT O R
A L L R E F R I G E R AT O R
WITH GLASS DOOR
ALL FREEZER
Energy Star Qualified
Energy Star Qualified
MODEL OPTIONS
MODEL OPTIONS
MODEL OPTIONS
Framed Design
601R/F
Framed Design
601RG/F
Framed Design
601F/F
Overlay Design
601R/O
Overlay Design
601RG/O
Overlay Design
601F/O
Classic Stainless Steel
601R/S
Classic Stainless Steel
601RG/S
Classic Stainless Steel
601F/S
Platinum Stainless Steel 601R/P
Platinum Stainless Steel 601RG/P
Platinum Stainless Steel 601F/P
Carbon Stainless Steel
Carbon Stainless Steel
Carbon Stainless Steel
601R/B
S P E C I F I C AT I O N S
601RG/B
S P E C I F I C AT I O N S
601F/B
S P E C I F I C AT I O N S
Overall Width
36" (914)
Overall Width
36" (914)
Overall Width
36" (914)
Overall Height
73" (1854)
Overall Height
73" (1854)
Overall Height
73" (1854)
Overall Depth
24" (610)
Overall Depth
24" (610)
Overall Depth
24" (610)
Refrigerator Capacity
19.9 cu ft (564 L)
Refrigerator Capacity
20.1 cu ft (569 L)
Freezer Capacity
19.3 cu ft (547 L)
Min Height Required
72 3/4" (1848)
Min Height Required
72 3/4" (1848)
Min Height Required
72 3/4" (1848)
Door Swing Clearance
36 1/16"
Door Swing Clearance
36 1/16"
Door Swing Clearance
36 1/16" (916)
Specify Door Swing
LH or RH
Specify Door Swing
LH or RH
Specify Door Swing
LH or RH
Annual Energy Usage
399 kWh | $37*
Annual Energy Usage
400 kWh | $37*
Annual Energy Usage
737 kWh | $67*
Shipping Wt (F)
391 lbs (177 kg)
Shipping Wt (F)
400 lbs (181 kg)
Shipping Wt (F)
378 lbs (171 kg)
Shipping Wt (O)
391 lbs (177 kg)
Shipping Wt (O)
400 lbs (181 kg)
Shipping Wt (O)
378 lbs (171 kg)
Shipping Wt (S/P/B)
420 lbs (191 kg)
Shipping Wt (S/P/B)
430 lbs (195 kg)
Shipping Wt (S/P/B)
406 lbs (184 kg)
(916)
(916)
R E F R I G E R AT O R F E AT U R E S
R E F R I G E R AT O R F E AT U R E S
F R E E Z E R F E AT U R E S
4 Adjustable Glass Shelves
4 Adjustable Glass Shelves
Automatic Ice Maker
1 Stationary Glass Shelf
1 Stationary Glass Shelf
3 Adjustable Wire Shelves
High-Humidity Compartment with Dividers
High-Humidity Compartment with Dividers
1 Stationary Glass Shelf
Adjustable Roll-Out Deli Basket
Triple-Pane UV Resistant Glass Door
3 Freezer Storage Drawers
3 Adjustable Door Shelves
5 Adjustable Door Shelves
Adjustable Dairy Compartment
Optional Accessory Roll-Out Deli Basket
Available
Egg Container
Egg Container
Optional High Altitude Glass Available**
601RG
MODEL 601R
MODEL 601RG
*Annual energy costs are based on
9.06 cents per kilowatt hour.
ACCESSORIES
**High altitude glass doors are
for installations at or above 5,000'
(1524 m) in elevation and will be
treated as a special order. Please
allow 90 days for delivery. When
ordering, add an (HA) before the (G)
to obtain the correct model number.
All models are shown in the stainless
steel design application.
MODEL 601F
Contact your Sub-Zero Dealer
Front panels for framed design
in white enamel and classic
stainless steel—not available for
glass door models
Side panels in white enamel and
classic stainless steel
Extended framed handles
Decorative overlay handles
90˚ and 105˚ door stop kits
Roll-out deli basket
(Model 601RG)
Dozen egg container with lid
Harness kit for Star-K compliance
7
B U I LT- I N R E F R I G E R AT I O N
MODEL 611
MODEL 611G
OVER-AND-UNDER
OVER-AND-UNDER
WITH GLASS DOOR
Energy Star Qualified
MODEL OPTIONS
*Annual energy costs are based on
9.06 cents per kilowatt hour.
MODEL OPTIONS
Framed Design
611/F
Framed Design
611G/F
**High altitude glass doors are
for installations at or above 5,000'
(1524 m) in elevation and will be
treated as a special order. Please
allow 90 days for delivery. When
ordering, add an (HA) before the (G)
to obtain the correct model number.
Overlay Design
611/O
Overlay Design
611G/O
Classic Stainless Steel
611/S
Classic Stainless Steel
611G/S
Platinum Stainless Steel 611/P
Platinum Stainless Steel 611G/P
Carbon Stainless Steel
Carbon Stainless Steel
611/B
S P E C I F I C AT I O N S
All models are shown in the stainless
steel design application.
611G/B
S P E C I F I C AT I O N S
Overall Width
30" (762)
Overall Width
30" (762)
Overall Height
84" (2134)
Overall Height
84" (2134)
Overall Depth
24" (610)
Overall Depth
24" (610)
Refrigerator Capacity
12.7 cu ft (360 L)
Refrigerator Capacity
12.9 cu ft (365 L)
Freezer Capacity
3.9 cu ft (110 L)
Freezer Capacity
3.9 cu ft (110 L)
Min Height Required
83" (2108)
Min Height Required
83" (2108)
Door Swing Clearance
30 1/8" (765)
Door Swing Clearance 30 1/8" (765)
Annual Energy Usage
463 kWh | $42*
Annual Energy Usage
544 kWh | $50*
Shipping Wt (F)
430 lbs (195 kg)
Shipping Wt (F)
471 lbs (214 kg)
Shipping Wt (O)
430 lbs (195 kg)
Shipping Wt (O)
471 lbs (214 kg)
Shipping Wt (S/P/B)
462 lbs (210 kg)
Shipping Wt (S/P/B)
476 lbs (216 kg)
R E F R I G E R AT O R ( D O O R )
R E F R I G E R AT O R ( D O O R )
3 Adjustable Glass Shelves
3 Adjustable Glass Shelves
1 Stationary Glass Shelf
1 Stationary Glass Shelf
High-Humidity Compartment with Divider
High-Humidity Compartment with Divider
Adjustable Roll-Out Deli Basket
Triple-Pane UV Resistant Glass Door
2 Adjustable Door Shelves
Adjustable Dairy Compartment
Optional Accessory Roll-Out Deli Basket
Available
Egg Container
Egg Container
Optional High Altitude Glass Available**
Dimensions in
parentheses are in
millimeters unless
otherwise specified.
8
FREEZER (DRAWER)
FREEZER (DRAWER)
Full-Extension Roll-Out Freezer Drawer
Full-Extension Roll-Out Freezer Drawer
Two-Tier Wire Storage Baskets
Two-Tier Wire Storage Baskets
Automatic Ice Maker
Automatic Ice Maker
MODEL 611
MODEL 611G
B U I LT- I N R E F R I G E R AT I O N
MODEL 650
MODEL 650G
OVER-AND-UNDER
OVER-AND-UNDER
WITH GLASS DOOR
Energy Star Qualified
MODEL OPTIONS
MODEL OPTIONS
ACCESSORIES
Framed Design
650/F
Framed Design
650G/F
Overlay Design
650/O
Overlay Design
650G/O
Classic Stainless Steel
650/S
Classic Stainless Steel
650G/S
Platinum Stainless Steel 650/P
Platinum Stainless Steel 650G/P
Carbon Stainless Steel
Carbon Stainless Steel
650/B
S P E C I F I C AT I O N S
650G/B
S P E C I F I C AT I O N S
Overall Width
36" (914)
Overall Width
36" (914)
Overall Height
84" (2134)
Overall Height
84" (2134)
Overall Depth
24" (610)
Overall Depth
24" (610)
Refrigerator Capacity
15.7 cu ft (445 L)
Refrigerator Capacity
16.0 cu ft (453 L)
Freezer Capacity
4.9 cu ft (139 L)
Freezer Capacity
4.9 cu ft (139 L)
Min Height Required
83" (2108)
Min Height Required
83" (2108)
Door Swing Clearance
36 1/16" (916)
Door Swing Clearance
36 1/16" (916)
Annual Energy Usage
481 kWh | $44*
Annual Energy Usage
565 kWh | $52*
Shipping Wt (F)
482 lbs (219 kg)
Shipping Wt (F)
523 lbs (237 kg)
Shipping Wt (O)
482 lbs (219 kg)
Shipping Wt (O)
523 lbs (237 kg)
Shipping Wt (S/P/B)
515 lbs (234 kg)
Shipping Wt (S/P/B)
529 lbs (240 kg)
R E F R I G E R AT O R ( D O O R )
R E F R I G E R AT O R ( D O O R )
3 Adjustable Glass Shelves
3 Adjustable Glass Shelves
1 Stationary Glass Shelf
1 Stationary Glass Shelf
High-Humidity Compartment with Dividers
High-Humidity Compartment with Dividers
Adjustable Roll-Out Deli Basket
Triple-Pane UV Resistant Glass Door
2 Adjustable Door Shelves
Adjustable Dairy Compartment
Optional Accessory Roll-Out Deli Basket
Available
Egg Container
Egg Container
Optional accessories
are available
through your
Sub-Zero dealer. To
obtain local dealer
information, visit the
Showroom Locator
section of our
website,
subzero.com.
Optional High Altitude Glass Available**
FREEZER (DRAWER)
FREEZER (DRAWER)
ACCESSORIES
Full-Extension Roll-Out Freezer Drawer
Full-Extension Roll-Out Freezer Drawer
Contact your Sub-Zero Dealer
Two-Tier Wire Storage Baskets
Two-Tier Wire Storage Baskets
Automatic Ice Maker
Automatic Ice Maker
Front and grille panels for framed
design in white enamel and
classic stainless steel
Side panels in white enamel and
classic stainless steel
Louvered, panel or stainless steel
grilles in 1" (25) increments from
10" (254) to 15" (381) high
Extended framed handles
Decorative overlay handles
Roll-out deli basket (Models 611G
and 650G)
Dozen egg container with lid
Harness kit for Star-K compliance
MODEL 650
MODEL 650G
9
B U I LT- I N R E F R I G E R AT I O N
MODEL 661
MODEL 642
MODEL 685
S I D E - B Y- S I D E
S I D E - B Y- S I D E
S I D E - B Y- S I D E
I C E | W AT E R D I S P E N S I N G
MODEL OPTIONS
MODEL OPTIONS
MODEL OPTIONS
Framed Design
661/F
Framed Design
642/F
Framed Design
685/F
Overlay Design
661/O
Overlay Design
642/O
Overlay Design
685/O
Classic Stainless Steel
661/S
Classic Stainless Steel
642/S
Classic Stainless Steel
685/S
Platinum Stainless Steel 661/P
Platinum Stainless Steel 642/P
Carbon Stainless Steel
Carbon Stainless Steel
661/B
S P E C I F I C AT I O N S
642/B
S P E C I F I C AT I O N S
S P E C I F I C AT I O N S
Overall Width
36" (914)
Overall Width
42" (1067)
Overall Width
42" (1067)
Overall Height
84" (2134)
Overall Height
84" (2134)
Overall Height
84" (2134)
Overall Depth
24" (610)
Overall Depth
24" (610)
Overall Depth
24" (610)
Refrigerator Capacity
12.5 cu ft (354 L)
Refrigerator Capacity
16.2 cu ft (459 L)
Refrigerator Capacity
15.6 cu ft (442 L)
Freezer Capacity
8.8 cu ft (249 L)
Freezer Capacity
8.2 cu ft (232 L)
Freezer Capacity
8.2 cu ft (232 L)
Min Height Required
83" (2108)
Min Height Required
83" (2108)
Min Height Required
83" (2108)
Door Swing Clearance
20 3/4" (527)
Door Swing Clearance
25 9/16" (649)
Door Swing Clearance
25 9/16" (649)
Annual Energy Usage
636 kWh | $58*
Annual Energy Usage
650 kWh | $59*
Annual Energy Usage
694 kWh | $63*
Shipping Wt (F)
500 lbs (227 kg)
Shipping Wt (F)
541 lbs (245 kg)
Shipping Wt (F)
569 lbs (258 kg)
Shipping Wt (O)
500 lbs (227 kg)
Shipping Wt (O)
541 lbs (245 kg)
Shipping Wt (O)
569 lbs (258 kg)
Shipping Wt (S/P/B)
538 lbs (244 kg)
Shipping Wt (S/P/B)
582 lbs (264 kg)
Shipping Wt (S)
608 lbs (276 kg)
R E F R I G E R AT O R F E AT U R E S
R E F R I G E R AT O R F E AT U R E S
R E F R I G E R AT O R F E AT U R E S
4 Adjustable Glass Shelves
4 Adjustable Glass Shelves
4 Adjustable Glass Shelves
1 Stationary Glass Shelf
1 Stationary Glass Shelf
1 Stationary Glass Shelf
High-Humidity Compartment
High-Humidity Compartment
High-Humidity Compartment
1 Storage Drawer
1 Storage Drawer
1 Storage Drawer
Adjustable Roll-Out Deli Basket
Adjustable Roll-Out Deli Basket
Adjustable Roll-Out Deli Basket
3 Adjustable Door Shelves
3 Adjustable Door Shelves
3 Adjustable Door Shelves
Adjustable Dairy Compartment
Adjustable Dairy Compartment
Adjustable Dairy Compartment
Egg Container
Egg Container
Egg Container
F R E E Z E R F E AT U R E S
F R E E Z E R F E AT U R E S
F R E E Z E R F E AT U R E S
Automatic Ice Maker
Automatic Ice Maker
Automatic Ice Maker
2 Adjustable Wire Shelves
3 Adjustable Wire Shelves
2 Adjustable Wire Shelves
1 Stationary Solid Shelf
1 Stationary Solid Shelf
1 Stationary Wire Shelf
4 Storage Drawers
3 Storage Drawers
3 Storage Drawers
5 Adjustable Door Shelves
5 Adjustable Door Shelves
5 Adjustable Door Shelves
2 Juice Can Shelves
MODEL 661
10
MODEL 642
MODEL 685
B U I LT- I N R E F R I G E R AT I O N
MODEL 632
MODEL 695
S I D E - B Y- S I D E
S I D E - B Y- S I D E
I C E | W AT E R D I S P E N S I N G
MODEL OPTIONS
MODEL OPTIONS
Framed Design
632/F
Framed Design
695/F
Overlay Design
632/O
Overlay Design
695/O
Classic Stainless Steel
632/S
Classic Stainless Steel
695/S
*Annual energy costs are based on
9.06 cents per kilowatt hour.
All models are shown in the stainless
steel design application.
Platinum Stainless Steel 632/P
Carbon Stainless Steel
632/B
S P E C I F I C AT I O N S
S P E C I F I C AT I O N S
Overall Width
48" (1219)
Overall Width
48" (1219)
Overall Height
84" (2134)
Overall Height
84" (2134)
Overall Depth
24" (610)
Overall Depth
24" (610)
Refrigerator Capacity
18.9 cu ft (535 L)
Refrigerator Capacity
18.2 cu ft (515 L)
Freezer Capacity
9.8 cu ft (278 L)
Freezer Capacity
9.8 cu ft (278 L)
Min Height Required
83" (2108)
Min Height Required
83" (2108)
Door Swing Clearance
29 1/4" (743)
Door Swing Clearance
29 1/4" (743)
Annual Energy Usage
675 kWh | $62*
Annual Energy Usage
747 kWh | $68*
Shipping Wt (F)
582 lbs (264 kg)
Shipping Wt (F)
610 lbs (277 kg)
Shipping Wt (O)
582 lbs (264 kg)
Shipping Wt (O)
610 lbs (277 kg)
Shipping Wt (S/P/B)
630 lbs (286 kg)
Shipping Wt (S)
656 lbs (298 kg)
R E F R I G E R AT O R F E AT U R E S
R E F R I G E R AT O R F E AT U R E S
ACCESSORIES
4 Adjustable Glass Shelves
4 Adjustable Glass Shelves
Contact your Sub-Zero Dealer
1 Stationary Glass Shelf
1 Stationary Glass Shelf
High-Humidity Compartment with Divider
High-Humidity Compartment with Divider
2 Storage Drawers
2 Storage Drawers
Adjustable Roll-Out Deli Basket
Adjustable Roll-Out Deli Basket
3 Adjustable Door Shelves
3 Adjustable Door Shelves
Adjustable Dairy Compartment
Adjustable Dairy Compartment
Egg Container
Egg Container
F R E E Z E R F E AT U R E S
F R E E Z E R F E AT U R E S
Automatic Ice Maker
Automatic Ice Maker
3 Adjustable Wire Shelves
2 Adjustable Wire Shelves
Extended framed handles
1 Stationary Solid Shelf
1 Stationary Wire Shelf
Decorative overlay handles
3 Storage Drawers
3 Storage Drawers
5 Adjustable Door Shelves
5 Adjustable Door Shelves
2 Juice Can Shelves
Front and grille panels for framed
design in white enamel and
classic stainless steel
Side panels in white enamel and
classic stainless steel
Louvered, panel or stainless steel
grilles in 1" (25) increments from
10" (254) to 15" (381) high
Framed panel kits (Models 685
and 695)*
90˚ and 105˚ door stop kits
Dozen egg container with lid
Harness kit for Star-K compliance
*Refer to page 19 for additional
information.
MODEL 632
MODEL 695
Dimensions in
parentheses are in
millimeters unless
otherwise specified.
11
B U I LT- I N R E F R I G E R AT I O N
MODEL 648PRO
MODEL 648PROG
S I D E - B Y- S I D E
B U I LT- I N O R F R E E - S TA N D I N G
S I D E - B Y- S I D E
WITH GLASS DOOR
B U I LT- I N O R F R E E - S TA N D I N G
*Annual energy costs are based on
9.06 cents per kilowatt hour.
S P E C I F I C AT I O N S
S P E C I F I C AT I O N S
Overall Width
48" (1219)
Overall Width
48" (1219)
**High altitude glass doors are
for installations at or above 5,000'
(1524 m) in elevation and will be
treated as a special order. Please
allow 90 days for delivery. When
ordering, add an (HA) before the (G)
to obtain the correct model number.
Overall Height
84" (2134)
Overall Height
84" (2134)
Overall Depth
25 7/8" (657)
Overall Depth
25 7/8" (657)
Refrigerator Capacity
18.4 cu ft (521 L)
Refrigerator Capacity
18.4 cu ft (521 L)
Freezer Capacity
11.7 cu ft (331 L)
Freezer Capacity
11.7 cu ft (331 L)
Min Height Required
83 1/2" (2121)
Min Height Required
83 1/2" (2121)
Door Swing Clearance
28 3/4" (730)
Door Swing Clearance
28 3/4" (730)
Annual Energy Usage
689 kWh | $63*
Annual Energy Usage
689 kWh | $63*
Shipping Weight
860 lbs (390 kg)
Shipping Weight
875 lbs (397 kg)
R E F R I G E R AT O R
R E F R I G E R AT O R
(Door and Two Drawers)
(Door and Two Drawers)
3 Adjustable Glass Shelves
3 Adjustable Glass Shelves
1 Stationary Glass Shelf
1 Stationary Glass Shelf
2 Adjustable Slide-Out Stainless Steel Bins
2 Adjustable Slide-Out Stainless Steel Bins
1 Crisper Lid
1 Crisper Lid
Dividers for Drawers Included
Dividers for Drawers Included
Triple-Pane UV Resistant Glass Door
Optional High Altitude Glass Available**
ACCESSORIES
FREEZER
FREEZER
Contact your Sub-Zero Dealer
(Door and Two Drawers)
(Door and Two Drawers)
Automatic Ice Maker
Automatic Ice Maker
Water Filtration Filter
Water Filtration Filter
3 Adjustable Stainless Steel Shelves
3 Adjustable Stainless Steel Shelves
1 Stationary Stainless Steel Shelf
1 Stationary Stainless Steel Shelf
1 Stainless Steel Ice Bucket
1 Stainless Steel Ice Bucket
MODEL 648PRO
MODEL 648PROG
90˚ door stop kit—right or left
hinge
Dozen egg container with lid
Slide-out stainless steel
refrigerator bin
Refrigerator drawer dividers
Classic stainless steel side panel
Free-standing kit—includes two
stainless steel side panels and
top lid
Dimensions in
parentheses are in
millimeters unless
otherwise specified.
12
B U I LT- I N R E F R I G E R AT I O N
PLANNING INFORMATION
PLUMBING CONSIDERATIONS
Although the Sub-Zero Built-In line offers a wide
range of designs and configurations, the basic
planning considerations for all models have
much in common. As you integrate Built-In
models into your overall plan, review installation
requirements for your particular model(s). The
Installation Specifications illustrations provide
planning information for all Built-In models—
framed, overlay and stainless steel.
For Built-In models with an automatic ice maker,
rough in the water supply line. Connect a 1/4"
OD copper line to the house supply, being sure
to use an easily accessible shut-off valve
between the supply and the refrigerator.
Do not use self-piercing valves. A saddle valve
kit (4200880) is available from your Sub-Zero
dealer.
Allow the door(s) to open a minimum of 90˚ or
you‘ll have problems removing drawers. With the
door opening at 90˚, you may have to move
drawers slightly to clear the door interior.
For Built-In models except Models 648PRO and
648PROG, a line filter is required when water
conditions have a high sediment content. The
ice maker operates on water pressure of 20 psi
(1.4 bar) to 100 psi (6.9 bar).
For corner installations, allow for a minimum 3"
(76) filler so that the door can open to 90˚. If
you‘re using raised panels, consider using a
wider filler.
IMPORTANT NOTE: In some cases a reverse
osmosis water filter system may not be able to
maintain the minimum water pressure consistently.
When units are installed side by side, a filler strip
is recommended. The width of this filler strip will
vary depending on the configuration and panels
you use.
Models 648PRO and 648PROG come with an
automatic ice maker and an integrated water
filtration system. This system operates on water
pressure between 35 psi (2.4 bar) and 120 psi
(8.3 bar).
Be sure to add the filler strip width to your
finished rough opening dimension. In any
installation of two units side by side without a
filler strip, add an additional 1/2" (13) to your
combined numbers. This will allow for the
proper width.
IMPORTANT NOTE: Refer to the full-scale illustrations at the end of this section for specifics
on door openings and filler size alternatives.
ELECTRICAL REQUIREMENTS
A 115 V AC, 60 Hz, 15 amp circuit breaker and
electrical supply are required. A separate circuit,
servicing only this appliance, is required.
All Sub-Zero Built-In models are equipped with a
power supply cord with a 3-prong grounding
plug, which must be plugged into a mating
3-prong grounding-type wall receptacle. Follow
the National Electrical Code and local codes and
ordinances when installing the receptacle. Refer
to the Installation Specifications illustration for
your model on the following pages.
IMPORTANT NOTE: A ground fault circuit
interrupter (GFCI) is not recommended and may
cause interruption of operation.
IMPORTANT NOTE: A reverse osmosis system
can be used with Models 648PRO and
648PROG, provided there is constant water
pressure of 20 psi (1.4 bar) to 120 psi (8.3 bar)
supplied to the unit at all times. In this application, the integrated water filtration system must
be set to bypass mode. This is achieved by
removing the water filter cartridge. Refer to the
PRO 48 Installation Instructions packed with the
unit for detailed instructions.
The water line should be routed up through the
floor within 1/2" (13) from the back wall and no
higher than 3" (76) off the floor. If you have to
come through the wall, make sure the water line
is no more than 3" (76) from the floor.
Regardless of the routing, allow 3' (1 m) of
excess copper tubing to remain outside the wall
or floor for easy connection to the unit. Refer to
Installation Specification illustrations.
MODEL OPTIONS
Model 601R
36" (914)
All Refrigerator
Model 601RG
36" (914)
All Refrigerator
with Glass Door
Model 601F
36" (914)
All Freezer
Model 611
30" (762)
Over-and-Under
Model 611G
30" (762)
Over-and-Under
with Glass Door
Model 650
36" (914)
Over-and-Under
Model 650G
36" (914)
Over-and-Under
with Glass Door
Model 661
36" (914)
Side-by-Side
Model 642
42" (1067)
Side-by-Side
Model 685
42" (1067)
Side-by-Side
Ice | Water Dispensing
Model 632
48" (1219)
Side-by-Side
Model 695
48" (1219)
Side-by-Side
Ice | Water Dispensing
Model 648PRO
48" (1219)
Side-by-Side
Built-In or Free-Standing
Model 648PROG
48" (1219)
Side-by-Side
with Glass Door
Built-In or Free-Standing
13
B U I LT- I N R E F R I G E R AT I O N
OVERALL DIMENSIONS
All Refrigerator | All Freezer Models
A L L R E F R I G E R AT O R
ALL FREEZER
73"
73"
73"
(1854)
(1854)
(1854)
Model 601R
All Refrigerator
Model 601RG
All Refrigerator
with Glass Door
Model 601F
All Freezer
36"
36"
36"
24"
(914)
(914)
(914)
(610)
Model 601R
Model 601RG
Model 601F
All Refrigerator
All Refrigerator
with Glass Door
All Freezer
Width
Width
Width
36" (914)
36" (914)
36" (914)
Height 73" (1854)
Height 73" (1854)
Height 73" (1854)
Depth
Depth
Depth
24" (610)
24" (610)
24" (610)
Illustrations shown in stainless steel design.
Refer to the fullscale illustrations at
the end of this
section for specifics
on door openings
and other
specifications.
I N S TA L L AT I O N S P E C I F I C AT I O N S
All Refrigerator | All Freezer Models
EXTEND
WATER LINE
APPROX 36" (914)
FROM BACK WALL
(601F ONLY)
24"
(610)
ROUGH
OPENING
DEPTH
Models 601R and 601RG, which do not have
an ice maker, will not require the water line
connection.
SHUT-OFF
VALVE
Dimensions are for finished rough openings.
TOP VIEW
Door swing clearances are based on
stainless steel door and handle dimensions.
3/8"(10)
FRAME
EXTENSION
23 7/8"
(606)
BEHIND
FRAME
90˚
36 1/16"
(916)
351/2" (902)
ROUGH OPENING WIDTH
72 3/4" (1848)
ROUGH OPENING
HEIGHT TO
FINISHED
FLOORING
72 3/4" (1848)
MINIMUM HEIGHT
REQUIRED TO
FINISHED
FLOORING
(LEVELERS IN)
LOCATE ELECTRICAL
WITHIN ENTIRE SHADED AREA
LOCATE WATER SUPPLY
WITHIN BOTTOM SHADED
AREA ONLY (601F ONLY)
Dimensions in
parentheses are in
millimeters unless
otherwise specified.
24"
6"
(610)
(152)
3"
11"
E
(279)
W
FRONT VIEW
14
(76)
B U I LT- I N R E F R I G E R AT I O N
OVERALL DIMENSIONS
Over-and-Under Refrigerator / Freezer Models
OVER-AND-UNDER
84"
84"
84"
84"
(2134)
(2134)
(2134)
(2134)
Model 611
Model 611G
with Glass Door
Model 650
Model 650G
with Glass Door
30"
30"
36"
36"
24"
(762)
(762)
(914)
(914)
(610)
Model 611
Model 611G
Model 650
Model 650G
with Glass Door
Width
30" (762)
Width
30" (762)
with Glass Door
Width
36" (914)
Width
36" (914)
Height 84" (2134)
Height 84" (2134)
Height 84" (2134)
Height 84" (2134)
Depth
Depth
Depth
Depth
24" (610)
24" (610)
24" (610)
24" (610)
Illustrations shown in stainless steel design.
I N S TA L L AT I O N S P E C I F I C AT I O N S
Over-and-Under Refrigerator / Freezer Models
24"
A) Rough Opening Width
29 1/2" (749)
B) Min Door Clearance
30 1/8" (765)
EXTEND
WATER LINE
APPROX 36" (914)
FROM BACK WALL
(610)
ROUGH
OPENING
DEPTH
Model 611
SHUT-OFF
VALVE
TOP VIEW
Model 611G
A) Rough Opening Width
29 1/2" (749)
B) Min Door Clearance
30 1/8" (765)
7"
E
(178)
3/8"(10)
6"
Model 650
FRAME
EXTENSION
(152)
A) Rough Opening Width
35 1/2" (902)
B) Min Door Clearance
36 1/16" (916)
90˚
A
A) Rough Opening Width
B) Min Door Clearance
36 1/16"
(606)
BEHIND
FRAME
LOCATE ELECTRICAL
WITHIN SHADED AREA
Model 650G
35 1/2"
237/8"
ROUGH OPENING WIDTH
(902)
B
(916)
Dimensions are for finished rough openings.
Door swing clearances are based on
stainless steel door and handle dimensions.
83" (2108)
MIN HEIGHT
REQUIRED TO
FINISHED
FLOORING
(LEVELERS IN)
751/2"
83 3/4" (2127)
ROUGH OPENING
HEIGHT TO
FINISHED
FLOORING WITH
STANDARD
11" (279) GRILLE
(1918)
LOCATE WATER SUPPLY
WITHIN SHADED AREA
3"
(76)
18"
6"
(457)
(152)
W
Refer to installation
instructions shipped
with each Wolf
product for detailed
specifications.
FRONT VIEW
15
B U I LT- I N R E F R I G E R AT I O N
OVERALL DIMENSIONS
Side-by-Side Refrigerator | Freezer Models
84"
(2134)
36"
42"
42"
48"
48"
24"
(914)
(1067)
(1067)
(1219)
(1219)
(610)
Model 685
Model 642
Model 661
Model 632
Model 695
Ice | Water Dispensing
Width
36" (914)
Width
42" (1067)
Width
42" (1067)
Ice | Water Dispensing
Width
48" (1219)
Width
48" (1219)
Height 84" (2134)
Height 84" (2134)
Height 84" (2134)
Height 84" (2134)
Height 84" (2134)
Depth
Depth
Depth
Depth
Depth
24" (610)
24" (610)
24" (610)
24" (610)
24" (610)
Illustrations shown in stainless steel design.
S I D E - B Y- S I D E
I N S TA L L AT I O N S P E C I F I C AT I O N S
Model 661
Side-by-Side Refrigerator | Freezer Models
Model 642
24"
Model 685
Ice | Water Dispensing
Model 661
A) Rough Opening Width
35 1/2" (902)
Model 632
B) Min Door Clearance
20 3/4" (527)
Model 695
Ice | Water Dispensing
Model 642
EXTEND
WATER LINE
APPROX 36" (914)
FROM BACK WALL
(610)
ROUGH
OPENING
DEPTH
SHUT-OFF
VALVE
TOP VIEW
A) Rough Opening Width
41 1/2" (1054)
B) Min Door Clearance
25 9/16" (649)
7"
6"
Model 685
3/8"(10)
FRAME
EXTENSION
(152)
237/8"
A) Rough Opening Width
41 1/2" (1054)
(606)
BEHIND
FRAME
B) Min Door Clearance
25 9/16" (649)
LOCATE ELECTRICAL
WITHIN SHADED AREA
Model 632
90˚
B
E
(178)
A
A) Rough Opening Width
47 1/2" (1206)
B) Min Door Clearance
29 1/4" (743)
Model 695
A) Rough Opening Width
47 1/2" (1206)
B) Min Door Clearance
29 1/4" (743)
ROUGH OPENING WIDTH
83" (2108)
MIN HEIGHT
REQUIRED TO
FINISHED
FLOORING
(LEVELERS IN)
751/2"
83 3/4" (2127)
ROUGH OPENING
HEIGHT TO
FINISHED
FLOORING WITH
STANDARD
11" (279) GRILLE
(1918)
Dimensions are for finished rough openings.
Dimensions in
parentheses are in
millimeters unless
otherwise specified.
Door swing clearances are based on
stainless steel door and handle dimensions.
LOCATE WATER SUPPLY
WITHIN SHADED AREA
3"
(76)
18"
6"
(457)
(152)
W
FRONT VIEW
16
B U I LT- I N R E F R I G E R AT I O N
OVERALL DIMENSIONS
PRO 48 Side-by-Side Refrigerator | Freezer Models
84"
23 7/8"
(2134)
(606)
PRO 48
S I D E - B Y- S I D E
Model 648PRO
Built-In or Free-Standing
Model 648PROG
with Glass Door
Built-In or Free-Standing
48"
48"
(1219)
(1219)
25 7/8"
(657)
30 5/32"
(766)
Model 648PRO
Model 648PROG
with Glass Door
Width
48" (1219)
Height 84" (2134)
Depth
23 7/8" (606)*
25 7/8" (657)**
Width
48" (1219)
Height 84" (2134)
Depth
23 7/8" (606)*
25 7/8" (657)**
*Depth from behind face frame to back of unit for standard installation.
**Depth from front of face frame to back of unit for flush installation.
Refer to the fullscale illustrations at
the end of this
section for specifics
on door openings
and other
specifications.
I N S TA L L AT I O N S P E C I F I C AT I O N S
PRO 48 Side-by-Side Refrigerator | Freezer Models
Built-In or Free-Standing
ROUGH
OPENING DEPTH
24" (610)
STANDARD
Models 648PRO and 648PROG can be
used free-standing or installed as a standard
or flush built-in application. For standard
built-in installations, the face frame of the
unit will extend 2" (51) beyond cabinetry.
In flush built-in installations, the front of the
face frame will be flush with surrounding
cabinetry.
MIN 36" (914)
1/4" COPPER
WATER LINE
26" (660)
SHUT-OFF
VALVE
FLUSH
TOP VIEW
7"
(178)
E
6"
Dimensions are for finished rough openings.
(152)
LOCATE ELECTRICAL
WITHIN SHADED AREA
23 7/8"
25 7/8"
(606)
BEHIND
FACE
FRAME
(657)
TO FRONT
OF FACE
FRAME
20 1/2" (521)
28 3/4"
(730)
ROUGH
OPENING WIDTH
1
47 /2" (1206) STANDARD
48" (1219) FLUSH
MIN HEIGHT
REQUIRED
TO FINISHED
FLOORING
(LEVELERS IN)
83 1/2" (2121)
STANDARD
83 3/4" (2127)
FLUSH
75 1/2"
ROUGH
OPENING HEIGHT
TO FINISHED
FLOORING
83 3/4" (2127)
STANDARD
84 1/8" (2137)
FLUSH
(1918)
48"
(1219)
LOCATE WATER SUPPLY
WITHIN SHADED AREA
6"
(152)
3" (76)
W
Refer to installation
instructions shipped
with each Wolf
product for detailed
specifications.
5 3/16"
(132)
FRONT VIEW
17
B U I LT- I N R E F R I G E R AT I O N
ACCESSORIES
Optional accessories
are available
through your
Sub-Zero dealer. To
obtain local dealer
information, visit the
Showroom Locator
section of our
website,
subzero.com.
ANTI-TIP BLOCKING KIT
FRAMED DOOR PANELS
To prevent the unit from tipping forward and to
provide a stable installation, the unit must be
secured in place with an anti-tip blocking kit. If
there is a solid soffit above the unit with clearance between the unit and the soffit of 1" (25)
or less, you won‘t need to block the unit. But for
installations with clearances of more than 1"
(25), you must block the unit with the anti-tip
blocking kit (wood block and hardware) provided
with each Sub-Zero Built-In model. Refer to the
Built-In Installation Instructions packed with the
appliance, which provides step-by-step procedures for making sure the unit is installed
properly.
If you and your client have ordered a framed
design model, you will be adding panels to give
the unit the custom Sub-Zero look. The framed
panel design option is available on all Built-In
units except Models 648PRO and 648PROG. For
exact door panel dimensions for Built-In framed
models, refer to the Framed Panel Specifications
on pages 20–21. Also refer to the full-scale
illustrations at the end of this section for panel
and handle considerations.
ADDING PANELS
If the thickness of the custom panels is less
than 1/4" (6), they must be backed up with a
sheet of shim material to build the total thickness to 1/4" (6). If the panel is thicker than 1/4"
(6), an edge must be routed around the panel to
ensure a proper fit. Refer to illustrations 1 and 2.
In your plan for panels, be sure you are working
with the Sub-Zero panel design family called for
in your design. If you have chosen the stainless
steel design, the unit will be shipped complete
with wrapped stainless steel doors and handle
hardware. You will not have to install door
panels.
Specifications on the following pages provide
panel dimensions and installation considerations
for framed and overlay door panels.
Side panels can be used with the framed,
overlay and stainless steel design applications.
Refer to specifications on page 26.
The traditional framed models come with an
elegant, smooth, full-length handle. Optional
extended full-length handles that provide
additional finger clearance for raised panels are
available through your Sub-Zero dealer.
IMPORTANT NOTE: On all framed models,
routing, recessing or optional extended handles
may be required on raised panels for finger clearance under the handle. Refer to the full-scale
illustrations at the end of this section.
For glass door Models 601RG, 611G and 650G,
the refrigerator door panel must include a cutout to accommodate the window. Refer to the
Framed Panel Specifications on pages 20–21.
IMPORTANT NOTE: On glass door models, the
glass portion of the door must be exposed and
not covered by any part of the panel.
For Models 685 and 695, the refrigerator door
panel must include a cut-out to accommodate
the glasswell and bezel. The thickness of the
panel in this area can range from 1/4" (6) to a
maximum of 1 1/8" (29). If the panel is thicker,
provisions must be made to rout out a space to
accommodate the decorative bezel surrounding
the glasswell.
PANELS 1/4" (6) THICK OR LESS
Trim reveal
1/4" (6) min
PANELS THICKER THAN 1/4" (6)
Trim reveal
1/4" (6) min
Rout to 1/4" (6)
thickness
1/4" (6)
Dimensions in
parentheses are in
millimeters unless
otherwise specified.
18
Panel
Illus. 1
Illus. 2
B U I LT- I N R E F R I G E R AT I O N
GLASSWELL PANEL OPTIONS
OPTIONAL PANEL GRILLE
If you choose not to use custom wood panels
above or below the glasswell for Model 685 or
695 framed application, a stainless steel insert
panel will be provided with the partial framed
accessory kit. This accessory kit (FRAMPAR),
includes partial framed molding and classic
stainless steel inset handle panel to provide a
spill-resistant finish above and below the glasswell on the refrigerator door only. Refer to the
Framed Panel Specifications for this option on
page 21.
An 11" (279) louvered grille is standard on
framed applications. Optional louvered grilles are
available in 1" (25) height increments from 10"
(254) to 15" (381) for all Built-In models except
Models 601R, 601RG, 601F, 648PRO and
648PROG.
With the framed retrofit accessory kit, existing
Model 680 or 690 door panels can be used on a
new Model 685 or 695 framed unit. This accessory kit (FRAMRET) includes framed retrofit
moldings and classic stainless steel inset handle
panels to accommodate existing Model 680 or
690 framed refrigerator and freezer door panels.
IMPORTANT NOTE: When using Model 680 or
690 raised panels with the framed retrofit kit
(FRAMRET), a 1/2" (13) trim reveal down to 1/4"
(6) thickness is necessary at the bezel in order
for the panels to fit properly.
You may choose to use Sub-Zero‘s optional
panel grille for some of your framed applications.
The panel grilles can be used with all Built-In
models except Models 601R, 601RG, 601F,
648PRO and 648PROG and are available in 1"
(25) height increments from 10" (254) to 15"
(381).
For each model, the width of the panel grille will
be the same, regardless of the height you have
chosen. To determine the panel grille insert size,
use the width dimension listed for your model
and the height dimension for the grille option
you have chosen. Specifications for the Panel
Grille Option are listed on page 21.
PANEL
REQUIREMENTS
The weight of
each framed door
panel cannot exceed
50 lbs (23 kg).
Both accessory kits are available through your
Sub-Zero dealer. Refer to the illustrations below.
FRAMED PANELS
To install framed
panels, see the
detailed procedures
outlined in the
Sub-Zero Built-In
Installation
Instructions.
Partial Framed Kit
FRAMPAR
Framed Retrofit Kit
FRAMRET
19
B U I LT- I N R E F R I G E R AT I O N
F R A M E D D O O R PA N E L S P E C I F I C AT I O N S
F R A M E D D O O R PA N E L S P E C I F I C AT I O N S
All Refrigerator | All Freezer Framed (F) Models
Over-and-Under Framed (F) Models
Model 601R
W
H
Model 611
W
H
Refrigerator Framed Panel
34 1/8" (867)
58 15/16" (1497)
Refrigerator Framed Panel
28 1/8" (714)
48 1/16" (1221)
Freezer Framed Panel
28 1/8" (714)
18 3/8" (467)
Raised Panel Handle Recess Location –
Refrigerator Panel
A) 29 15/32" (749)
Raised Panel Handle Recess Location –
Refrigerator Panel
A) 24 1/32" (610)
Model 601RG
W
H
Freezer Panel
B) 14 1/16" (357)
Refrigerator Framed Panel
34 1/8" (867)
58 15/16" (1497)
Raised Panel Handle Recess Location –
Refrigerator Panel
A) 29 15/32" (749)
Window Cut-Out Dimensions
25 3/8" (645)
41 3/16" (1046)
Window Cut-Out Location
C) 4 3/8" (111)
D) 13 3/8" (340)
Model 601F
W
H
Freezer Framed Panel
34 1/8" (867)
58 15/16" (1497)
Model 611G
W
H
Refrigerator Framed Panel
28 1/8" (714)
48 1/16" (1221)
Freezer Framed Panel
28 1/8" (714)
18 3/8" (467)
Raised Panel Handle Recess Location –
Raised Panel Handle Recess Location –
Refrigerator Panel
A) 24 1/32" (610)
Freezer Panel
B) 14 1/16" (357)
Window Cut-Out Dimensions
19 3/8" (492)
39 5/16" (999)
Window Cut-Out Location
C) 4 3/8" (111)
D) 4 3/8" (111)
Model 650
W
H
Refrigerator Framed Panel
34 1/8" (867)
48 1/16" (1221)
Freezer Framed Panel
34 1/8"
18 3/8" (467)
A) 29 15/32" (749)
Freezer Panel
IMPORTANT NOTE: Panel specifications are for Built-In framed (F)
models. Panel specifications for overlay models are on pages 24–25.
(867)
Raised Panel Handle Recess Location –
Refrigerator Panel
A) 24 1/32" (610)
Freezer Panel
B) 17 1/16" (433)
Model 650G
W
H
Refrigerator Framed Panel
34 1/8" (867)
48 1/16" (1221)
Freezer Framed Panel
34 1/8" (867)
18 3/8" (467)
Raised Panel Handle Recess Location –
Refrigerator Panel
A) 24 1/32" (610)
Freezer Panel
B) 17 1/16" (433)
Window Cut-Out Dimensions
25 3/8" (645)
39 5/16" (999)
Window Cut-Out Location
C) 4 3/8" (111)
D) 4 3/8" (111)
IMPORTANT NOTE: Panel specifications are for Built-In framed (F)
models. Panel specifications for overlay models are on pages 24–25.
FRAMED PANELS
C
C
Panel specifications
are for Built-In
framed (F) models.
C
C
C
14"(356)
14"(356)
14"(356)
H
Dimensions in
parentheses are in
millimeters unless
otherwise specified.
20
14"(356)
H
H
H
A
A
C
A
A
D
D
B
W
W
Models 601R
and 601F
Model 601RG
H
W
Models 611 and 650
B
H
W
Models 611G and 650G
B U I LT- I N R E F R I G E R AT I O N
F R A M E D D O O R PA N E L S P E C I F I C AT I O N S
PARTIAL FRAMED DOOR PANEL OPTION
Side-by-Side Framed (F) Models
Ice | Water Dispensing Framed (F) Models
Model 661
W
H
Model 685
W
H
Refrigerator Framed Panel
19 1/8" (486)
67 11/16" (1719)
Refrigerator Partial Framed Panel
15 5/8" (397)
67 11/16" (1719)
Freezer Framed Panel
14 5/8" (371)
67 11/16"
Freezer Partial Framed Panel
15 5/8" (397)
67 11/16" (1719)
Model 695
W
H
Refrigerator Partial Framed Panel
17 15/16" (456) 67 11/16" (1719)
Freezer Partial Framed Panel
17 15/16" (456) 67 11/16" (1719)
(1719)
Raised Panel Handle Recess Location –
A) 38 5/32" (969)
Refrigerator | Freezer Panel
Model 642
W
H
Refrigerator Framed Panel
24" (610)
67 11/16" (1719)
Freezer Framed Panel
15 5/8" (397)
67 11/16" (1719)
The partial framed accessory kit (FRAMPAR) is required for this option.
Kit includes partial framed molding and classic stainless steel inset
handle panels for above and below glasswell on the refrigerator door.
Raised Panel Handle Recess Location –
Refrigerator | Freezer Panel
A) 38 5/32" (969)
Model 685
W
H
Refrigerator Framed Panel
24" (610)
67 11/16" (1719)
Freezer Framed Panel
15 5/8" (397)
67 11/16" (1719)
Models 611 and 611G
W
Glasswell Cut-Out Dimensions
5 7/ 8"
12 7/16"
Grille Panel Width
28 3/16" (716)
PANEL GRILLE OPTION
Glasswell Location (Refrigerator)
E)
(150)
1 9/16"
(39)
F)
Framed (F) Models
(315)
28 9/16"
(726)
Model 632
W
Refrigerator Framed Panel
27 11/16" (703) 67 11/16" (1719)
H
Freezer Framed Panel
17 15/16" (456) 67 11/16" (1719)
Raised Panel Handle Recess Location –
A) 38 5/32" (969)
Refrigerator | Freezer Panel
W
Grille Panel Width
34 3/16" (868)
Models 642 and 685
W
Grille Panel Width
40 3/16" (1021)
Models 632 and 695
W
Grille Panel Width
46 3/16" (1173)
10" (254) Grille
H
Grille Panel Height
8 15/16" (227)
Model 695
W
Refrigerator Framed Panel
27 11/16" (703) 67 11/16" (1719)
11" (279) Grille (standard)
H
Freezer Framed Panel
17 15/16" (456) 67 11/16" (1719)
Grille Panel Height
9 15/16" (252)
Glasswell Cut-Out Dimensions
5 7/8" (150)
12 7/16" (315)
12" (305) Grille Height
H
F) 28 9/16" (726)
Grille Panel Height
10 15/16" (278)
Glasswell Location (Refrigerator)
E)
H
Models 650, 650G, 661
1 9/16"
(39)
IMPORTANT NOTE: Panel specifications are for Built-In framed (F)
models. Panel specifications for overlay models are on pages 24–25.
For Models 685 and 695, panel thickness in the glasswell area can
range from 1/4" (6) to a maximum of 1 1/8" (29). If the panel is thicker,
you must rout out a minimum 1/4" (6) flat landing area to accommodate the bezel surrounding the glasswell.
13" (330) Grille
H
Grille Panel Height
11 15/16" (303)
14" (356) Grille
H
Grille Panel Height
12 15/16" (329)
15" (381) Grille
H
Grille Panel Height
13 15/16" (354)
For panel grille insert size, use width dimension listed
for your model and height dimension for grille option.
11" (279) grille is standard.
FRAMED PANELS
E
H
H
H
14" (356)
F
A
W
W
Models 661, 642
and 632
W
W
Models 685 and 695
W
To install framed
panels, see the
detailed procedures
outlined in the
Sub-Zero Built-In
Installation
Instructions.
W
Models 685 and 695
Partial Framed Option
21
B U I LT- I N R E F R I G E R AT I O N
OVERLAY DOOR PANELS
If you and your client have ordered an overlay
design model, you will be adding panels to give
the unit the custom Sub-Zero look. The overlay
panel design option is available on all Built-In
units except Models 648PRO and 648PROG.
For exact door panel dimensions for Built-In
overlay models, refer to the Overlay Panel Specifications on pages 24–25.
The overlay design allows decorative panels to
cover the door trim for a more seamless
appearance that blends with the design of the
room. To achieve this look, the most common
way is to work with three panels—the decorative
overlay panel, a 0.10" (3) spacer panel and a 1/4"
(6) backer panel. Depending on your cabinet
manufacturer, this could be one panel routed for
different dimensions or, more likely, three different panels.
PANEL
REQUIREMENTS
The overlay door
panel assembly must
be a minimum of
5/ 8" (16) thick and
cannot exceed 50 lbs
(23 kg).
Regardless of the physical construction of the
panels (routing or three-panel assembly), you will
need to follow the Overlay Panel Specifications
on the following pages for exact sizing and panel
placement to ensure a proper fit.
Illustration 3 is a cross section view of the threepanel assembly showing placement of the door,
drawer or grille trim. Illustration 4 shows a rear
view of the three-panel assembly and critical
dimensions, standard for all models.
Spacer Panel
Overlay Panel
If you are using an overlay door panel with
Model 611, 611G, 650 or 650G, it is necessary
to rout a space for the unit‘s lower hinge plate
so it does not strike the door panel. Refer to
illustration 5.
For Models 611, 611G, 650 and 650G, you will
minimize the reveal between the bottom of the
overlay door panel and the top of the overlay
drawer panel. Refer to illustration 6.
IMPORTANT NOTE: If you choose not to rout a
space for the lower hinge plate, you can reduce
the total height of the overlay panel (decorative
panel only) by 1/2" (13).
Do not exceed the overlay decorative panel
dimensions for Models 611, 611G, 650 or
650G listed on page 24. If you try to make
the reveal tighter between the door and
drawer panels, the panels may hit when
opening and closing, causing possible
damage to the panels and the Sub-Zero unit.
Overlay Panel
Spacer Panel
1/4" (6)
.10"
(3)
IMPORTANT NOTE: Keep in mind that the
Sub-Zero door panels have the potential for
hitting adjacent cabinets and/or countertops
when they are opened. You need to be aware of
your surrounding cabinetry and space limitations
when using the overlay models. Refer to the fullscale illustrations at the end of this section.
Overlay Panel
Backer Panel
Backer
Panel
Spacer Panel
Overlay Panel
Spacer Panel
5/16"
1/4" (6) Backer
5/16" (8) min
(8)
Panel
3" (76)
27/32"
5/32" (4)
1/16" (2)
Illus. 3
22
Door / Drawer /
Grille Trim
Backer
Panel
~3/4"
(19)
Illus. 4
.10"
(3) 1/4" (6)
1/2"
(13)
3/8" (10)
Illus. 5
Bottom Edge –
Hinge Side
(rear view)
(21)
17/32"
(13)
Illus. 6
B U I LT- I N R E F R I G E R AT I O N
OVERLAY DOOR PANELS
For glass door Models 601RG, 611G and 650G,
the refrigerator door panel must include a cutout to accommodate the window. Refer to the
Overlay Panel Specifications for Models 601RG,
611G and 650G on page 24.
Illustration 8 shows how you can box out a
landing space for the bezel using stiles and rails
to create this space. Again, keep in mind, that
the total thickness of the panel at this level must
not exceed 1 1/8" (29).
IMPORTANT NOTE: On glass door models, the
glass portion of the door must be exposed and
not covered by any part of the panel.
OVERLAY PANEL GRILLE
For Models 685 and 695, the refrigerator door
panel must include a cut-out to accommodate
the glasswell and bezel. The thickness of the
panel in this area can range from 1/4" (6) to a
maximum of 1 1/8" (29).
IMPORTANT NOTE: Regardless of the thickness
of the overlay panel for Model 685 or 695, you
must plan for a flat ’landing’ space for the
decorative bezel surrounding the glasswell area.
Refer to page 25 for exact cut-out dimensions of
the glasswell area in the overlay, spacer and
backer panels. This ’landing’ area can be accomplished in a number of different ways. We are
showing two in Illustrations 7 and 8 below.
Illustration 7 shows how you can recess the
bezel to the inset panel. You must rout out a
space to accommodate the 12 7/8" (327) height
of the bezel. Also keep in mind that the amount
of material you will rout out of the stile will vary
because of the thickness of this element.
However, the width of the stile immediately
adjacent to the bezel must be 1 7/16" (37). DO
NOT cut the entire stile to this dimension. In this
illustration you can see that rails above and
below the bezel give this a finished look. Make
sure that the bezel is not supporting weight
from the panel.
Routing
Required
Overlay grille panels for the panel grille match
the design of the door panels. Overlay units,
except Models 601R, 601RG and 601F, come
standard with an 11" (279) panel grille. Optional
grilles are available in 1" (25) height increments
from 10" (254) to 15" (381). Overlay grille panel
specifications for the panel grille are listed on
page 25. Also refer to illustration 4 on page 22
for additional overlay panel dimensions.
OVERLAY PANELS
To install overlay
panels, see the
detailed procedures
outlined in the
Sub-Zero Built-In
Installation
Instructions.
Do not exceed the panel dimensions listed
for the appropriate overlay grille panel you
are specifying. The decorative panel cannot
be any larger or it may restrict the airflow
to the compressor area and cause problems
with the operation of the Sub-Zero unit.
Glasswell
Cut-Out
12 7/8"
(327)
1 7/16" (37)
Width
of Stile
Adjacent
to Bezel
Illus. 7
Height
of Bezel
2" (51)
Edge of
Panel to
Cut-Out
Illus. 8
Dimensions in
parentheses are in
millimeters unless
otherwise specified.
23
B U I LT- I N R E F R I G E R AT I O N
O V E R L AY D O O R PA N E L S P E C I F I C AT I O N S
O V E R L AY D O O R PA N E L S P E C I F I C AT I O N S
All Refrigerator | All Freezer Overlay (O) Models
Over-and-Under Overlay (O) Models
Model 601R
W
H
Model 611
W
H
Refrigerator Overlay Panel
34 7/16" (875)
59 1/4" (1505)
Refrigerator Overlay Panel
28 7/16" (722)
48 7/8" (1241)
Refrigerator Spacer Panel
33 1/2" (851)
58 5/16"
Refrigerator Spacer Panel
27 1/2" (699)
47 7/16" (1205)
Refrigerator Backer Panel
34 1/8" (867)
58 15/16" (1497)
Refrigerator Backer Panel
28 1/8" (714)
48 1/16" (1221)
Model 601RG
W
H
Refrigerator Overlay Panel
34 7/16" (875)
59 1/4" (1505)
Refrigerator Spacer Panel
33 1/2" (851)
58 5/16" (1481)
Refrigerator Backer Panel
34 1/8" (867)
58 15/16" (1497)
Window Cut-Out Dimensions
25 7/16" (646)
41 1/4" (1048)
Window Cut-Out Location
C) 4 1/2" (114)
D) 13 1/2" (343)
Model 601F
W
H
Freezer Overlay Panel
34 7/16" (875)
59 1/4" (1505)
Freezer Spacer Panel
33 1/2" (851)
58 5/16" (1481)
Freezer Backer Panel
34 1/8" (867)
58 15/16" (1497)
(1481)
Freezer Overlay Panel
28 7/16" (722)
18 11/16" (475)
Freezer Spacer Panel
27 1/2" (699)
17 3/4" (451)
Freezer Backer Panel
28 1/8" (714)
18 3/8" (467)
Model 611G
W
H
Refrigerator Overlay Panel
28 7/16" (722)
48 7/8" (1241)
Refrigerator Spacer Panel
27 1/2" (699)
47 7/16" (1205)
Refrigerator Backer Panel
28 1/8" (714)
48 1/16" (1221)
Freezer Overlay Panel
28 7/16" (722)
18 11/16" (475)
Freezer Spacer Panel
27 1/2" (699)
17 3/4" (451)
Freezer Backer Panel
28 1/8" (714)
18 3/8" (467)
Window Cut-Out Dimensions
19 7/16"
39 3/8" (1000)
Window Cut-Out Location
IMPORTANT NOTE: Panel specifications are for Built-In overlay (O)
models. Panel specifications for framed models are on pages 20–21.
C)
(494)
4 1/ 2"
(114)
D) 5" (127)
Model 650
W
H
Refrigerator Overlay Panel
34 7/16" (875)
48 7/8" (1241)
Refrigerator Spacer Panel
33 1/2" (851)
47 7/16" (1205)
Refrigerator Backer Panel
34 1/8"
48 1/16" (1221)
Freezer Overlay Panel
34 7/16" (875)
18 11/16" (475)
Freezer Spacer Panel
33 1/2"
(851)
17 3/4" (451)
Freezer Backer Panel
34 1/8"
(867)
18 3/8" (467)
Model 650G
W
H
Refrigerator Overlay Panel
34 7/16" (875)
48 7/8" (1241)
Refrigerator Spacer Panel
33 1/2"
(851)
47 7/16" (1205)
Refrigerator Backer Panel
34 1/8"
(867)
48 1/16" (1221)
(867)
Freezer Overlay Panel
34 7/16" (875)
18 11/16" (475)
Freezer Spacer Panel
33 1/2" (851)
17 3/4" (451)
Freezer Backer Panel
34 1/8" (867)
18 3/8" (467)
Window Cut-Out Dimensions
25 7/16" (646)
39 3/8" (1000)
Window Cut-Out Location
C) 4 1/2" (114)
D) 5" (127)
IMPORTANT NOTE: Panel specifications are for Built-In overlay (O)
models. Panel specifications for framed models are on pages 20–21.
OVERLAY PANELS
C
C
Panel specifications
are for Built-In
overlay (O) models.
Dimensions in
parentheses are in
millimeters unless
otherwise specified.
24
C
C
C
C
H
H
H
H
D
D
W
W
Models 601R
and 601F
Model 601RG
H
W
Models 611 and 650
H
W
Models 611G and
650G
B U I LT- I N R E F R I G E R AT I O N
O V E R L AY D O O R PA N E L S P E C I F I C AT I O N S
OVERLAY GRILLE PANEL
Side-by-Side Overlay (O) Models
Overlay (O) Models
Width Dimensions
Model 661
W
H
Models 611 and 611G
Refrigerator Overlay Panel
19 7/16" (494)
68" (1727)
Overlay Panel Width
28 7/16" (722)
Refrigerator Spacer Panel
18 1/2" (470)
67 1/16" (1703)
Spacer Panel Width
27 1/2" (699)
Refrigerator Backer Panel
19 1/8"
67 11/16"
Backer Panel Width
28 1/8" (714)
Freezer Overlay Panel
14 15/16" (379) 68" (1727)
Freezer Spacer Panel
14" (356)
67 1/16" (1703)
Models 650, 650G, 661
W
Freezer Backer Panel
14 5/8"
67 11/16"
Overlay Panel Width
34 7/16" (875)
Spacer Panel Width
33 1/2" (851)
Backer Panel Width
34 1/8"
(486)
(371)
(1719)
(1719)
Models 642 and 685
W
H
Refrigerator Overlay Panel
24 5/16" (618)
68" (1727)
W
(867)
Refrigerator Spacer Panel
23 3/8" (594)
67 1/16" (1703)
Models 642 and 685
W
Refrigerator Backer Panel
24" (610)
67 11/16" (1719)
Overlay Panel Width
40 7/16" (1027)
Freezer Overlay Panel
15 15/16" (405) 68" (1727)
Spacer Panel Width
39 1/2" (1003)
Freezer Spacer Panel
15" (381)
67 1/16" (1703)
Backer Panel Width
40 1/8" (1019)
Freezer Backer Panel
15 5/8" (397)
67 11/16" (1719)
Models 632 and 695
W
Overlay Panel Width
46 7/16" (1180)
Models 632 and 695
Refrigerator Overlay Panel
W
H
28" (711)
68" (1727)
67 1/16" (1703)
Spacer Panel Width
45 1/2" (1156)
Backer Panel Width
46 1/8" (1172)
Refrigerator Spacer Panel
27 1/16" (687)
Refrigerator Backer Panel
27 11/16"
Freezer Overlay Panel
18 1/4" (464)
68" (1727)
Freezer Spacer Panel
17 5/16" (440)
67 1/16" (1703)
10" (254) Grille
Freezer Backer Panel
17 15/16"
67 11/16"
Overlay Panel Height
OVERLAY PANELS
To install overlay
panels, see the
detailed procedures
outlined in the
Sub-Zero Built-In
Installation
Instructions.
(703) 67 11/16" (1719)
Height Dimensions
(456)
(1719)
Glasswell Cut-Out –
Models 685 and 695
W
H
Glasswell Cut-Out Dimensions
5 7/8" (150)
12 7/16" (315)
Glasswell Location (Overlay)
E) 1 11/16" (43) F) 28 3/4" (730)
Glasswell Location (Spacer)
E) 1 1/4" (31)
F) 28 1/4" (718)
Glasswell Location (Backer)
E) 1 9/16" (39)
F) 28 9/16" (726)
IMPORTANT NOTE: Panel specifications are for Built-In overlay (O)
models. Panel specifications for framed models are on pages 20–21.
For Models 685 and 695, panel thickness in the glasswell area can
range from 1/4" (6) to a maximum of 1 1/8" (29). If the panel is thicker,
you must rout out a minimum 1/4" (6) flat landing area to accommodate the bezel surrounding the glasswell.
E
F
W
Models 661, 642
and 632
9 1/4" (235)
Spacer Panel Height
8 5/16" (211)
Backer Panel Height
8 15/16" (227)
11" (279) Grille (standard)
H
Overlay Panel Height
10 1/4" (260)
Spacer Panel Height
9 5/16" (237)
Backer Panel Height
9 15/16" (252)
12" (305) Grille Height
H
Overlay Panel Height
11 1/4" (286)
Spacer Panel Height
10 5/16" (262)
Backer Panel Height
10 15/16" (278)
13" (330) Grille
H
Overlay Panel Height
12 1/4" (311)
Spacer Panel Height
11 5/16" (287)
Backer Panel Height
11 15/16" (303)
14" (356) Grille
H
Overlay Panel Height
13 1/4" (337)
Spacer Panel Height
12 5/16" (313)
Backer Panel Height
12 15/16" (329)
15" (381) Grille
H
Overlay Panel Height
14 1/4" (362)
Spacer Panel Height
13 5/16" (338)
Backer Panel Height
13 15/16" (354)
H
H
W
H
W
W
For grille panel size, use width dimensions
listed for your model and height dimensions
for grille option. 11" (279) grille is standard.
Panel grille is available for all overlay units
except Models 601R, 601RG and 601F.
Models 685 and 695
25
B U I LT- I N R E F R I G E R AT I O N
ACCESSORIES
Optional accessories
are available
through your
Sub-Zero dealer. To
obtain local dealer
information, visit the
Showroom Locator
section of our
website,
subzero.com.
HANDLE HARDWARE
SIDE PANELS
Overlay models come without handle hardware.
The beauty of this design is that you can match
the surrounding cabinet hardware. You or the
cabinet manufacturer must provide handle
hardware to match the overall decorating
scheme.
Side panels can be used with the framed,
overlay and stainless steel design applications.
When planning for side panels with the installation of a Built-In model, you need to be aware of
space configuration to achieve a pleasing fit.
Depending on the exact panel you are using with
your unit, the height of the panel will vary.
The handle hardware must be installed before
installing the panel assembly. Use larger D-style
handles. If screws with thick heads are used,
the screws will need to be countersunk into the
door before the panel is put into place.
IMPORTANT NOTE: Sub-Zero does not recommend using single pull knobs on any of its BuiltIn models.
For overlay Models 685 and 695, mounting
placement of the refrigerator door handle must
assure proper access to the glasswell and
adequate clearance under the handle. Illustration
9 shows placement of the refrigerator door
handle in relationship to the glasswell bezel on
stainless steel models.
Cut-outs around the toe kick and grille area are
required if a 1/4" (6) thick panel will be inserted
into the main frame channel. The panel will need
to be 24" (610) deep. If a 3/8" (10) thick panel is
used, the panel will abut the main frame and
should be 23 7/8" (606) deep. Refer to illustrations 10–12 below for placement of toe kick and
grille area cut-outs for your specific model.
These dimensions do not apply to Models
648PRO and 648PROG.
The toe kick area may or may not be cut out
depending on the look you want to achieve.
IMPORTANT NOTE: The use of side panels may
change the width of your rough opening.
Optional stainless steel handles are available in a
variety of diameters and lengths, as are handles
to match the color and style of Wolf ovens.
Contact your Sub-Zero dealer for specifics.
Refer to the full-scale illustrations at the end of
this section for handle hardware considerations.
13 1/4" (337)
13 1/4" (337)
1/4" (6)
1/4" (6)
1"
(25)
23 7/8" (606)
BEHIND FRAME
Glasswell
Profile
2"
(51)
23 7/8" (606)
BEHIND FRAME
23 7/8" (606)
BEHIND FRAME
Handle
Profile
Illus. 9
1/4" (6)
3" (76)
4" (102)
4" (102)
3" (76)
Illus. 10—Models 601R,
601RG and 601F
26
4" (102)
3" (76)
Illus. 11—Models 611, 611G,
650 and 650G
3" (76)
Illus. 12—Models 661, 642, 632,
685 and 695
B U I LT- I N R E F R I G E R AT I O N
PANEL AND HANDLE PROFILE – FRAMED APPLICATION
OPTIONAL
EXTENDED
FULL-LENGTH
HANDLE
FULL-SCALE
T E M P L AT E S
1"
2"
3"
(25)
(51)
(76)
11/4"(32) PANEL
STANDARD
FULL-LENGTH
HANDLE
1"(25) PANEL
3/4"(19) PANEL
1/2"(13) PANEL
1/4"(6) PANEL
1/4"(6) FRAMED PANEL
The full-scale
illustrations on the
following pages
enable you to understand some of the
unique situations
you may face as you
plan for the installation of the Built-In
models. Use these
illustrations as
templates for
panel and handle
hardware
considerations.
DOOR
The full-scale illustration above shows
handle placement for the framed application standard full-length handle and
the optional extended full-length handle
shown in the dashed line.
Dimensions in
parentheses are in
millimeters unless
otherwise specified.
27
B U I LT- I N R E F R I G E R AT I O N
PANEL AND HANDLE PROFILE – OVERLAY AND STAINLESS STEEL APPLICATION
STANDARD STAINLESS STEEL HANDLE
1"
2"
3"
(51)
(76)
11/4" (32) PANEL
1" (25) PANEL
3/4" (19) PANEL
5/8" (16) PANEL
1/2" (13) PANEL
1/4" (6) PANEL
1/4" (6) APPROXIMATE THICKNESS OF WRAPPED STAINLESS STEEL DOOR
DOOR
NOTE: FOR OVERLAY APPLICATIONS, OPTIONAL STAINLESS STEEL HANDLE
MUST BE MOUNTED ON PANEL MINIMUM 5/8" (16) THICK.
The full-scale illustration above shows
handle placement for the standard
stainless steel handle on the wrapped
stainless steel door and on overlay
panel applications shown in the dashed
line.
IMPORTANT NOTE: For overlay applications, the panel must be a minimum of
5/ 8" (16) thick to support mounting the
handle hardware.
For overlay applications, mount door
handles close to the opening edge of
the door for ease of opening.
Dimensions in
parentheses are in
millimeters unless
otherwise specified.
28
B U I LT- I N R E F R I G E R AT I O N
PANEL AND HANDLE PROFILE – 130˚ DOOR OPENING (TOP VIEW)
The full-scale illustration shows the
panel and handle profile for 130˚ door
opening with a 2" (51) filler strip.
Interference of door panels with
handles at maximum door swing may
require the use of an optional 90˚ door
stop available through your Sub-Zero
dealer.
130˚ DOOR OPENING
WITH 2" (51) FILLER STRIP
SUB-ZERO UNIT
SUB-ZERO UNIT
(TOP VIEW)
FILLER STRIP
2" (51)
ALLOW FOR FILLER LAP
BEHIND FLANGE
DOOR CLOSED
OVERLAY PANEL
3/4" (19) THICK
(NOMINAL)
MAIN FRAME
1"
(
STANDARD
FRAMED
FULL-LENGTH
HANDLE
11
/4"
APPROX
PROFILE OF
STAINLESS
STEEL DOOR
AND HANDLE
(3
2)
PA
NE
25
3
L
)P
/4"
AN
(
1
1
E
9
L
)P
/2"
AN
(1
EL
3)
*1
PA
/4"
NE
(6
L
)P
AN
EL
HINGE
DOOR OPEN @ 130˚
OPTIONAL
FRAMED EXTENDED
FULL-LENGTH HANDLE
*Approximate thickness of wrapped
stainless steel door.
29
B U I LT- I N R E F R I G E R AT I O N
OVERLAY PANEL APPLICATION – 90˚ DOOR OPENING (TOP VIEW)
The full-scale illustration
shows what considerations you need to make
for overlay panel applications and how they
may interact with
adjacent cabinets and
countertops.
OPENING
90˚ DOOR
(TOP VIEW)
NOMINAL OVERALL
WIDTH OF SUB-ZERO
SUB-ZERO UNIT
237/8" (606) TO REAR
OF SUB-ZERO
MAIN FRAME
0" (0)
1/4" (6)
DOOR CLOSED
1/2" (13)
3/4" (19)
HINGE
1" (25)
11/4" (32)
11/2" (38)
13/4" (44)
2" (51)
21/4" (57)
21/2" (63)
DOOR OPEN @ 90˚
23/4" (70)
3" (76)
31/4" (83)
*1/4" (6) PANEL
1/2" (13) PANEL
3/4" (19) PANEL
1" (25) PANEL
11/4" (32) PANEL
31/2" (89)
OVERLAY PANEL
3/4" (19) THICK (NOMINAL)
Dimensions in
parentheses are in
millimeters unless
otherwise specified.
30
*Approximate thickness of wrapped
stainless steel door.
INTEGRATED REFRIGERATION
INTEGRATED REFRIGERATION
A L L R E F R I G E R AT O R | A L L F R E E Z E R
NEW
For generations, the Sub-Zero name has been
synonymous with built-in refrigeration. With the
Integrated line, we have taken the idea a step
further—refrigerators and freezers you can hide
anywhere in the house, inside the furniture or
cabinetry of your choosing.
Created to blend invisibly into your home‘s
decor, the Integrated line lets you integrate
refrigeration into the kitchen, master suite, media
room or workout room. Available as tall units or
two-drawer base units, the Integrated line
expands the possibilities for the way you shape
your home.
Tall units are 80" (2032) high and offered in two
different widths—27" (686) and 36" (914). The
27" (686) wide tall unit can be ordered as an all
refrigerator, all freezer or combination refrigerator
(upper cabinet) and freezer (drawers). The 36"
(914) wide tall unit is offered as an all refrigerator or combination unit. All of these models are
24" (610) deep.
Base units are offered in the 27" (686) width
only. They can be ordered as an all refrigerator,
all freezer or combination refrigerator (top
drawer) and freezer (bottom drawer). Base units
are 34 1/2" (876) high and 24" (610) deep.
You just need to add whatever beautiful cabinetry you want to use. Optional stainless steel
panels with tubular handles are offered in the
classic, platinum and carbon stainless steel
finishes and are ordered and shipped as sales
accessories. There are some size limitations on
the premium finishes of platinum and carbon
stainless steel.
27"
27"
36"
(686)
(686)
(914)
80"
80"
80"
(2032)
(2032)
(2032)
MODEL 700TR
MODEL 700TF(I)
MODEL 736TR
All Refrigerator
All Freezer
All Refrigerator
OVER-AND-UNDER
27"
36"
(686)
(914)
80"
80"
(2032)
(2032)
MODEL 700TC(I)
MODEL 736TC(I)
Refrigerator | Freezer
Refrigerator | Freezer
DRAWERS
27"
27"
27"
(686)
(686)
(686)
For information regarding specific Integrated
models, refer to the illustrations in this section.
341/2"
341/2"
341/2"
(876)
(876)
(876)
MODEL 700BR
MODEL 700BF(I)
MODEL 700BC(I)
All Refrigerator
All Freezer
Refrigerator | Freezer
Energy Star
Qualified
Comprehensive installation instructions are
shipped with each model. Refer to those
instructions in preparing and installing all
Sub-Zero products. The instructions can also
be found on our website, subzero.com.
With the installation of a harness kit,
tall models are Star-K compliant to meet
strict religious regulations in conjunction
with specific instructions found on
www.star-k.org. Drawer models are
Star-K certified from the factory with
no extra wiring harness required. For
details about the harness kit, contact
your Sub-Zero dealer.
31
INTEGRATED REFRIGERATION
MODEL 700TR
MODEL 736TR
A L L R E F R I G E R AT O R
A L L R E F R I G E R AT O R
MODEL 700TF
NEW
ALL FREEZER
MODEL OPTIONS
Automatic Ice Maker
S P E C I F I C AT I O N S
S P E C I F I C AT I O N S
700TFI
S P E C I F I C AT I O N S
Overall Width
27" (686)
Overall Width
36" (914)
Overall Width
27" (686)
Overall Height
80" (2032)
Overall Height
80" (2032)
Overall Height
80" (2032)
Overall Depth
24" (610)
Overall Depth
24" (610)
Overall Depth
24" (610)
Refrigerator Capacity
15.5 cu ft (439 L)
Refrigerator Capacity
20.9 cu ft (592 L)
Freezer Capacity
15.3 cu ft (433 L)
Min Height Required
79 1/2" (2019)
Min Height Required
79 1/2" (2019)
Min Height Required
79 1/2" (2019)
Door Swing Clearance
25 1/2"
Door Swing Clearance
34 1/2"
Door Swing Clearance
25 1/2" (648)
Specify Door Swing
LH or RH
Specify Door Swing
LH or RH
Specify Door Swing
LH or RH
Drawer Clearance
19 1/2" (495)
Drawer Clearance
19 1/2" (495)
Drawer Clearance
19 1/2" (495)
Annual Energy Usage
425 kWh | $39*
Annual Energy Usage
478 kWh | $44*
Annual Energy Usage
652 kWh | $60*
Shipping Weight
360 lbs (163 kg)
Shipping Weight
480 lbs (218 kg)
Shipping Weight
360 lbs (163 kg)
(648)
(876)
R E F R I G E R AT O R F E AT U R E S
R E F R I G E R AT O R F E AT U R E S
F R E E Z E R F E AT U R E S
Dual Refrigeration
Dual Refrigeration
1 Temperature Zone
2 Temperature Zones
2 Temperature Zones
3 Adjustable Glass Shelves
3 Adjustable Glass Shelves
3 Adjustable Glass Shelves
1 Stationary Shelf
1 Stationary Shelf
1 Stationary Shelf
2 Storage Drawers
2 Storage Drawers
2 Storage Drawers
2 Removable Drawer Dividers (700TF)
Removable Crisper Cover
Removable Crisper Cover
1 Removable Drawer Divider (700TFI)
2 Removable Drawer Dividers
4 Removable Drawer Dividers
4 Adjustable Door Shelves
Adjustable Deli Drawer
Adjustable Deli Drawer
Automatic Defrost
3 Adjustable Door Shelves
3 Adjustable Door Shelves
Automatic Ice Maker
Adjustable Dairy Compartment
Adjustable Dairy Compartment
Egg Container
Egg Container
PANEL OPTIONS
PANEL OPTIONS
PANEL OPTIONS
Integrated
Integrated
Integrated
Classic, platinum or carbon stainless
steel finish (includes handles)**
Classic, platinum or carbon stainless
steel finish (includes handles)**
Classic, platinum or carbon stainless
steel finish (includes handles)**
MODEL 700TR
MODEL 736TR
MODEL 700TF(I)
32
Model 700TFI
INTEGRATED REFRIGERATION
MODEL 700TC
MODEL 736TC
OVER-AND-UNDER
OVER-AND-UNDER
MODEL OPTIONS
Automatic Ice Maker
MODEL OPTIONS
700TCI
S P E C I F I C AT I O N S
Automatic Ice Maker
736TCI
S P E C I F I C AT I O N S
Overall Width
27" (686)
Overall Width
36" (914)
Overall Height
80" (2032)
Overall Height
80" (2032)
Overall Depth
24" (610)
Overall Depth
24" (610)
Refrigerator Capacity
10.2 cu ft (289 L)
Refrigerator Capacity
13.3 cu ft (377 L)
Freezer Capacity
5.1 cu ft (144 L)
Freezer Capacity
7.1 cu ft (201 L)
Min Height Required
79 1/2" (2019)
Min Height Required
79 1/2" (2019)
Door Swing Clearance
25 1/2"
Door Swing Clearance
34 1/2" (876)
Specify Door Swing
LH or RH
Specify Door Swing
LH or RH
Drawer Clearance
19 1/2" (495)
Drawer Clearance
19 1/2" (495)
Annual Energy Usage
540 kWh | $49*
Annual Energy Usage
569 kWh | $52*
Shipping Weight
360 lbs (163 kg)
Shipping Weight
480 lbs (218 kg)
(648)
*Annual energy costs are based on
9.06 cents per kilowatt hour.
**Optional stainless steel panels and
handles are ordered and shipped as
sales accessories. For additional
information on panel and handle sizes
and applications, check our website,
subzero.com.
R E F R I G E R AT O R ( D O O R )
R E F R I G E R AT O R ( D O O R )
ACCESSORIES
Dual Refrigeration
Dual Refrigeration
Contact your Sub-Zero Dealer
3 Adjustable Glass Shelves
3 Adjustable Glass Shelves
1 Stationary Shelf
1 Stationary Shelf
Adjustable Deli Drawer
High-Humidity Crisper Drawer with Dividers
3 Adjustable Door Shelves
3 Adjustable Door Shelves
Adjustable Dairy Compartment
Adjustable Dairy Compartment
Egg Container
Egg Container
Tubular handles in classic,
platinum and carbon stainless
steel
FREEZER (DRAWERS)
FREEZER (DRAWERS)
High-humidity crisper drawer and
shelf assembly*
2 Removable Drawer Dividers (700TC)
2 Removable Drawer Dividers (736TC)
1 Removable Drawer Divider (700TCI)
1 Removable Drawer Divider (736TCI)
Automatic Defrost
Automatic Defrost
Crisper cover with lid*
Automatic Ice Maker (700TCI)
Automatic Ice Maker (736TCI)
Dozen egg container with lid*
PANEL OPTIONS
PANEL OPTIONS
Integrated
Integrated
Classic, platinum or carbon stainless
steel finish (includes handles)**
Classic, platinum or carbon stainless
steel finish (includes handles)**
MODEL 700TC(I)
MODEL 736TC(I)
Classic stainless steel front
panels—platinum and carbon
available in certain sizes
Adjustable deli drawer and shelf
assembly*
Dual installation heater kit
Harness kit for Star-K compliance
*Accessory is not available for
every model.
Dimensions in
parentheses are in
millimeters unless
otherwise specified.
33
INTEGRATED REFRIGERATION
MODEL 700BR
MODEL 700BF
MODEL 700BC
R E F R I G E R AT O R D R A W E R S
FREEZER DRAWERS
R E F R I G E R AT O R | F R E E Z E R
DRAWERS
Energy Star Qualified
MODEL OPTIONS
Automatic Ice Maker
S P E C I F I C AT I O N S
MODEL OPTIONS
700BFI
S P E C I F I C AT I O N S
Automatic Ice Maker
700BCI
S P E C I F I C AT I O N S
Overall Width
27" (686)
Overall Width
27" (686)
Overall Width
27" (686)
Overall Height
34 1/2" (876)
Overall Height
34 1/2" (876)
Overall Height
34 1/2" (876)
Overall Depth
24" (610)
Overall Depth
24" (610)
Overall Depth
24" (610)
Refrigerator Capacity
5.3 cu ft (150 L)
Freezer Capacity
5.1 cu ft (144 L)
Refrigerator Capacity
2.9 cu ft (82 L)
Min Height Required
34" (864)
Min Height Required
34" (864)
Freezer Capacity
2.1 cu ft (59 L)
Drawer Clearance
19 1/2" (495)
Drawer Clearance
19 1/2" (495)
Min Height Required
34" (864)
Annual Energy Usage
337 kWh | $31*
Annual Energy Usage
488 kWh | $45*
Drawer Clearance
19 1/2" (495)
Shipping Weight
190 lbs (86 kg)
Shipping Weight
190 lbs (86 kg)
Annual Energy Usage
448 kWh | $41*
Shipping Weight
190 lbs (86 kg)
R E F R I G E R AT O R F E AT U R E S
F R E E Z E R F E AT U R E S
F E AT U R E S
1 Temperature Zone
1 Temperature Zone
2 Temperature Zones
2 Storage Drawers
2 Storage Drawers
2 Storage Drawers
Removable Crisper Cover
2 Removable Drawer Dividers (700BF)
Removable Crisper Cover
2 Removable Drawer Dividers
1 Removable Drawer Divider (700BFI)
1 Removable Drawer Divider (700BC)
Automatic Defrost
Automatic Ice Maker (700BCI)
Automatic Ice Maker (700BFI)
PANEL OPTIONS
PANEL OPTIONS
PANEL OPTIONS
Integrated
Integrated
Integrated
Classic, platinum or carbon stainless
steel finish (includes handles)**
Classic, platinum or carbon stainless
steel finish (includes handles)**
Classic, platinum or carbon stainless
steel finish (includes handles)**
MODEL 700BR
MODEL 700BF(I)
MODEL 700BC(I)
*Annual energy costs are based on
9.06 cents per kilowatt hour.
ACCESSORIES
**Optional stainless steel panels and
handles are ordered and shipped as
sales accessories. For additional
information on panel and handle sizes
and applications, check our website,
subzero.com.
Contact your Sub-Zero Dealer
Front panels in classic, platinum
and carbon stainless steel
Tubular handles in classic, platinum
and carbon stainless steel
Crisper cover with lid*
Dimensions in
parentheses are in
millimeters unless
otherwise specified.
34
Dozen egg container with lid*
Dual installation heater kit
*Accessory is not available for
every model.
INTEGRATED REFRIGERATION
INTEGRATED FEATURES
All Integrated models accept wood or stainless
steel panels. The optional stainless steel panels
and handles are available in classic, platinum and
carbon stainless steel finishes at the 80" (2032)
height, and only classic stainless steel at the 84"
(2134) height. Stainless steel panels are ordered
and shipped as sales accessories.
Dairy Shelf. This magnetically sealed compartment is fully adjustable on the tall refrigerator and
combination units.
Functional Design. These models can be placed
anywhere in the home. Think about “point-ofuse refrigeration” when planning where to place
your units.
Deli Drawer. Smaller items are not lost in this
handy feature of the Models 700TR and 700TC(I).
Available as a sales accessory for Model 736TC(I).
Integrated Design. All Sub-Zero models are 24"
(610) deep. Tall Integrated units are 80" (2032)
high and are offered in two different widths—
27" (686) and 36" (914). All base units are 27"
(686) wide and 34 1/2" (876) high.
Microprocessor. The “brains” of the Integrated
units, this computer allows the best in temperature control, efficiency and food preservation.
Temperature Zones. On tall refrigerator and
combination units, you have the flexibility of
having two temperatures within the same unit.
Automatic Defrost. Depending on usage and
exact climate, the Integrated unit will adapt to
the unique situation and adjust accordingly to
offer greater efficiency. Integrated freezer and
combination units have an automatic defrost
system.
Kickplate. The adjustable solid kickplate meets
standards of the American Institute of Architects. The toe kick area for a solid, decorative
kickplate is 4" (102) high by 3" (76) deep. You
can show a 10" (254) toe kick, but you cannot
cover the louvers of the kickplate. If you choose,
the kickplate can be painted.
Front Venting. All models have the mechanical
equipment in an area below the lower drawer.
The lower drawer panel can extend to cover
these louvers, but a removable decorative kickplate cannot cover the fins.
Lighting. Flat to the ceiling, superior lighting
provides white, efficient light in cabinet and
drawer units.
Door / Drawer Alarm. When activated, if your
door or drawer is accidentally left open for more
than 30 seconds, an audible alarm will sound.
Spill-Proof Shelves. The cabinet section of the
tall units features adjustable spill-proof one-piece
glass shelves that are easily removed for
cleaning.
Crisper Cover. On the tall and base refrigerator
units and the base combination unit, a removable
crisper cover is offered for one of the drawer
sections.
Crisper—Model 736TC(I). Model 736TC(I) is
equipped with a sealed crisper. It is large and
deep, with smooth sides for easy cleaning. The
space features removable dividers.
Egg Container. You can store a dozen eggs in
this removable egg container with lid in the tall
refrigerator and tall combination units.
SUB-ZERO
WARRANTY
Sub-Zero products
are covered by a
two, five and twelve
year residential
warranty (exclusions
apply). See warranty
details at the end of
this guide.
Ice Maker. An automatic ice maker, providing
crescent-shaped ice, is available as an option on
the tall and base freezers as well as the tall and
base combination units. This optional equipment
must be factory installed.
Door Swing. You can choose left or right door
swing on the tall units. This option must be
ordered when requesting the unit. You cannot
reverse the door in the field.
Dual-Action Hinge. An exclusive dual-action
hinge is featured on all of the tall units, allowing
for a fully integrated look.
Door Stop. On all of the tall units, a 90˚ door stop
is built in to the hinge. Normal door swing is 105˚.
Temperature Zones. With the microprocessor in
the Integrated models, you have the capability of
setting different optimum temperatures.
T E M P E R AT U R E Z O N E S
Model 700BR – One zone,
34˚F (1˚C) to 45˚F (7˚C)
Models 700TR and 736TR –
Two zones, 34˚F (1˚C) to 45˚F (7˚C)
Models 700BF(I) and 700TF(I) –
One zone, -5˚F (-21˚C) to +5˚F (-15˚C)
Model 700TF(I) – One zone,
-5˚F (-21˚C) to +5˚F (-15˚C)
Model 700BC(I) – Two zones,
34˚F (1˚C) to 45˚F (7˚C) top drawer;
-5˚F (-21˚C) to +5˚F (-15˚C) bottom
drawer
Models 700TC(I) and 736TC(I) –
Two zones, 34˚F (1˚C) to 45˚F (7˚C)
cabinet; -5˚F (-21˚C) to +5˚F (-15˚C)
drawers
35
INTEGRATED REFRIGERATION
PLANNING INFORMATION
Before moving the Integrated unit into place, be
sure that the finished opening dimensions, electrical and plumbing locations and minimum door
and drawer clearances are accurate. Refer to the
Installation Specifications illustration for your
model on the following pages. Be sure your
installer has this information before finishing
work is completed.
Integrated models without an automatic ice
maker will not require the plumbing connections
shown in the illustrations.
The height of the tall unit is set at 80" (2032).
You can allow the top of the door panel to
exceed this dimension with caution. If you are
working with 84" (2134) or 96" (2438) neighboring panels, you can utilize door panels to match
this height. Other critical dimensions regarding
the door swing, drawer openings and toe kick
clearance are noted in the Overall Dimensions
illustrations on the following pages. Also refer to
the full-scale illustrations at the end of this
section for specifics on door openings and other
specifications.
IMPORTANT NOTE: The anti-tip bracket must be
installed to prevent the unit from tipping
forward.
ELECTRICAL REQUIREMENTS
A 115 V AC, 60 Hz, 15 amp circuit breaker and
electrical supply are required. A separate circuit,
servicing each base and tall unit, is required.
All Sub-Zero Integrated models are equipped
with a power supply cord with a 3-prong
grounding plug, which must be plugged into a
mating 3-prong grounding-type wall receptacle.
Follow the National Electrical Code and local
codes and ordinances when installing the
receptacle.
IMPORTANT NOTE: The electrical outlet must
be placed so the grounding prong is to the right
of the thinner blades. The outlet must be flush
with the back wall. Refer to the Installation
Specifications illustration for your model for
exact placement.
IMPORTANT NOTE: A ground fault circuit
interrupter (GFCI) is not recommended and may
cause interruption of operation.
Dimensions in
parentheses are in
millimeters unless
otherwise specified.
36
Do not use an extension cord or 2-prong
adapter. Electrical ground is required.
Do not under any circumstances remove
the power supply cord ground prong.
PLUMBING CONSIDERATIONS
For models with an automatic ice maker, rough
in the water supply line. Connect a 1/4" OD
copper line to the house supply, being sure to
use an easily accessible shut-off valve between
the supply and the unit. This shut-off valve
should not be installed behind the unit.
Do not use self-piercing valves. A saddle valve
kit (4200880) is available from your Sub-Zero
dealer. An in-line filter is required when water
conditions have a high sediment content. The ice
maker operates on constant water pressure
between 20 psi (1.4 bar) and 100 psi (6.9 bar).
IMPORTANT NOTE: In some cases, a reverse
osmosis water filter system may not be able to
maintain the minimum pressure consistently.
The Installation Specifications illustration for
your model on the following pages shows the
precise placement of the water line. When
routing the water through the side walls, you
must place the water line within 1/2" (13) of the
floor and as close as possible to the back wall.
The line must be routed around the anti-tip
bracket so it clears the bracket and the leveling
feet of the unit as shown in the top view of the
illustration. Regardless of the routing, allow for
27" (686) of excess copper tubing to remain
outside the wall or floor for easy connection to
the unit.
IMPORTANT NOTE: Do not route water supply
line in front of the compressor tray. The tray
must be slid forward for service.
INTEGRATED REFRIGERATION
OVERALL DIMENSIONS
Models 700TR, 700TF(I) and 700TC(I)
27"
24"
(686)
(UNIT DIMENSION)
(610)
(UNIT DIMENSION)
TOP OF
ROUGH
OPENING
14"(356)
A L L R E F R I G E R AT O R
ALL FREEZER
13/16"
(21)
24"
Model 700TR
All Refrigerator
(610)
DOOR
MOUNTING
DETAIL
DOOR/ DRAWER
CLOSED
DOOR/ DRAWER
CLOSED
Model 700TF
All Freezer
80"*
(2032)
19 1/2"*
25 1/2"* (495)
90˚
3/8"
789/16"*
(10)
(1995)
Model 700TFI
All Freezer
with Ice Maker
105˚
(648)
25 7/8" (657)
131/4"
1/2" (337)
(13)
DRAWER
MOUNTING DETAIL
4 5/8"* (117)
90˚ DOOR OPENING
341/2"*
101/4"
MAXIMUM DOOR OPENING
TOP VIEW
(876)
*DOOR/DRAWER PANEL THICKNESS NOT INCLUDED – DIMENSION WILL VARY WITH INSTALLATION
(260)
OVER-AND-UNDER
Refrigerator | Freezer
Model 700TC
Model 700TCI
with Ice Maker
203/8"
93/4"
(518)
(248)
4"
FRONT VIEW
SIDE VIEW
(102)
*1/2" (13) +_ ADJUSTMENT IN LEVELING LEGS
I N S TA L L AT I O N
S P E C I F I C AT I O N S
TOP VIEW
Models 700TR, 700TF(I) and 700TC(I)
11/2"
(38)
Models without an ice maker will not
require the water line connection.
6"
ANTI-TIP
BRACKET*
(152)
13 1/2"
25"
27"
(343)
(635)
15 1/2"
9"
(394)
(229)
(686)
ANTI-TIP
BRACKET
13 1/2"
27"
(343)
(686)
Depth
11/2"
11/2"
(38)
(38)
24" (610)
Finished Opening
Width
27" (686)
Height 80" (2032)
27"
25"
(686)
LOCATE WATER LINE
(REAR ENTRY) WITHIN
SHADED AREA
4 1/2"
(114)
27" (686)
Height 80" (2032)
Depth
(635)
25" (635)*
*The depth of the unit
is 24" (610) from the
front of the unit to its
back. Your design may
necessitate moving the
unit back or cabinets
forward to achieve a
flush fit. This will
require a minimum
rough opening depth
of 25" (635).
LOCATE ELECTRICAL WITHIN
SHADED AREA – ORIENT GROUND
PRONG TO RIGHT AS SHOWN
ANTI-TIP
BRACKET
Overall Dimensions
Width
WATER LINE
SIDE ENTRY
LOCATIONS
WATER LINE
BOTTOM ENTRY
LOCATION
*PLACEMENT OF THE
ANTI-TIP BRACKET
SHOULD BE 24" (610)
FROM THE FRONT OF THE
UNIT WITHOUT PANELS
TO THE BACK OF THE
ANTI-TIP BRACKET.
MODEL 700TR
MODEL 700TF(I)
MODEL 700TC(I)
TOP VIEW
80"
(2032)
3"
(76)
1/4"
(6)
13" (330)
9"
(229)
2 1/2" (64)
3/4"
(19)
15 1/2" (394)
NOTE: ANTI-TIP BRACKET MUST BE INSTALLED TO
PREVENT UNIT FROM TIPPING FORWARD
ANTI-TIP
BRACKET
FRONT VIEW
SIDE VIEW
WATER LINE
SIDE ENTRY
LOCATION
Refer to installation
instructions shipped
with each Wolf
product for detailed
specifications.
37
INTEGRATED REFRIGERATION
OVERALL DIMENSIONS
Models 736TR and 736TC(I)
36"
24"
(914)
(UNIT DIMENSION)
(610)
(UNIT DIMENSION)
TOP OF
ROUGH
OPENING
14"(356)
A L L R E F R I G E R AT O R
15/16"
(33)
Model 736TR
All Refrigerator
24"
DOOR MOUNTING
DETAIL
(610)
DOOR/DRAWER
CLOSED
DOOR/DRAWER
CLOSED
80"*
(2032)
OVER-AND-UNDER
Refrigerator | Freezer
191/2"*
341/2"* (495)
90˚
Model 736TC
3/ 8"
7713/16"*
(10)
(1976)
105˚
(876)
Model 736TCI
with Ice Maker
347/8" (886)
131/4"
1/2" (337)
(13)
DRAWER MOUNTING
DETAIL
90˚ DOOR OPENING
MAXIMUM DOOR OPENING
TOP VIEW
(876)
*DOOR/DRAWER PANEL THICKNESS NOT INCLUDED – DIMENSION WILL VARY WITH INSTALLATION
101/4"
(260)
203/8"
93/4"
(518)
(248)
4"
FRONT VIEW
(102)
SIDE VIEW
*1/2" (13) +_ ADJUSTMENT IN LEVELING LEGS
MODEL 736TR
MODEL 736TC(I)
TOP VIEW
I N S TA L L AT I O N
S P E C I F I C AT I O N S
Models 736TR and 736TC(I)
1 1/2"
Overall Dimensions
Width
36" (914)
Height 80" (2032)
Depth
24" (610)
(38)
25"
Models without an ice maker
will not require the water line
connection.
(635)
TOP VIEW
6"
ANTI-TIP
BRACKET*
(152)
18" (457)
27"
13 1/2"
20" (508)
ANTI-TIP
BRACKET
18" (457)
27"
(686)
(686)
WATER LINE
SIDE ENTRY
LOCATIONS
(343)
WATER LINE
BOTTOM ENTRY
LOCATION
Finished Opening
Width
*PLACEMENT OF THE
ANTI-TIP BRACKET
SHOULD BE 24" (610)
FROM THE FRONT OF THE
UNIT WITHOUT PANELS
TO THE BACK OF THE
ANTI-TIP BRACKET.
36" (914)
Height 80" (2032)
Depth
25" (635)*
*The depth of the unit
is 24" (610) from the
front of the unit to its
back. Your design may
necessitate moving the
unit back or cabinets
forward to achieve a
flush fit. This will
require a minimum
rough opening depth
of 25" (635).
(38)
25"
(635)
LOCATE ELECTRICAL WITHIN
SHADED AREA – ORIENT GROUND
PRONG TO RIGHT AS SHOWN
LOCATE WATER LINE
(REAR ENTRY) WITHIN
SHADED AREA
ANTI-TIP
BRACKET
80"
(2032)
3"
(114)
(76)
1 /4 "
(6)
38
1 1/2"
(38)
36"
4 1/2"
Dimensions in
parentheses are in
millimeters unless
otherwise specified.
1 1 /2 "
(914)
17 1/2" (445)
13 1/2"
(343)
2 1/2" (64)
3/4"
(19)
20" (508)
NOTE: ANTI-TIP BRACKET MUST BE INSTALLED TO
PREVENT UNIT FROM TIPPING FORWARD
ANTI-TIP
BRACKET
FRONT VIEW
7"*
(178)
341/2"*
SIDE VIEW
WATER LINE
SIDE ENTRY
LOCATION
INTEGRATED REFRIGERATION
OVERALL DIMENSIONS
Models 700BR, 700BF(I) and 700BC(I)
3/8"
27"
24"
(686)
(UNIT DIMENSION)
(610)
(UNIT DIMENSION)
(10)
DRAWERS
131/4"
1/2" (337)
(13)
DRAWER
MOUNTING DETAIL
Model 700BR
All Refrigerator
24"
(610)
341/2"*
101/4"
(876)
203/8"
Model 700BF
All Freezer
DRAWER CLOSED
(260)
Model 700BFI
All Freezer
with Ice Maker
93/4"
(518)
(248)
191/2"*
(495)
4"
FRONT VIEW
Model 700BC
Refrigerator | Freezer
SIDE VIEW
(102)
*1/2" (13) +_ ADJUSTMENT IN LEVELING LEGS
Model 700BCI
Refrigerator | Freezer
with Ice Maker
257/8" (657)
TOP VIEW
*DRAWER PANEL THICKNESS NOT INCLUDED
TOP VIEW
I N S TA L L AT I O N
S P E C I F I C AT I O N S
Models 700BR, 700BF(I) and 700BC(I)
11/2"
(38)
Models without an ice maker
will not require the water line
connection.
6"
ANTI-TIP
BRACKET*
(152)
13 1/2"
25"
27"
(343)
15 1/2"
(394)
(635)
MODEL 700BR
MODEL 700BF(I)
MODEL 700BC(I)
TOP VIEW
9"
(686)
ANTI-TIP
BRACKET
13 1/2"
Overall Dimensions
27"
(343)
(686)
WATER LINE
SIDE ENTRY
LOCATIONS
(229)
WATER LINE
BOTTOM ENTRY
LOCATION
Width
27" (686)
Height 34 1/2" (876)
Depth
24" (610)
Finished Opening
*PLACEMENT OF THE
ANTI-TIP BRACKET
SHOULD BE 24" (610)
FROM THE FRONT OF THE
UNIT WITHOUT PANELS
TO THE BACK OF THE
ANTI-TIP BRACKET.
11/2"
11/2"
(38)
(38)
Width
27" (686)
Height 34 1/2" (876)
27"
Depth
25"
(686)
341/2"
(876)
NOTE: ANTI-TIP BRACKET MUST BE INSTALLED TO
PREVENT UNIT FROM TIPPING FORWARD
ANTI-TIP
BRACKET
FRONT VIEW
25" (635)*
(635)
SIDE VIEW
WATER LINE
SIDE ENTRY
LOCATION
*The depth of the unit
is 24" (610) from the
front of the unit to its
back. Your design may
necessitate moving the
unit back or cabinets
forward to achieve a
flush fit. This will
require a minimum
rough opening depth of
25" (635).
LOCATE ELECTRICAL WITHIN
SHADED AREA – ORIENT GROUND
PRONG TO RIGHT AS SHOWN
ANTI-TIP
BRACKET
LOCATE WATER LINE
(REAR ENTRY) WITHIN
SHADED AREA
4 1/2"
3"
(114)
(76)
1/4"
(6)
13" (330)
9"
(229)
2 1/2" (64)
3/4"
(19)
15 1/2" (394)
Refer to installation
instructions shipped
with each Wolf
product for detailed
specifications.
39
INTEGRATED REFRIGERATION
PANEL
REQUIREMENTS
Door and drawer
panels must be a
minimum of 5/8" (16)
thick.
The door panel
cannot exceed 40 lbs
(18 kg) and each
drawer panel must
not exceed 12 lbs
(5 kg) for 27" (686)
wide units. For 36"
(914) wide units, the
door panel weight
limit is 53 lbs (24 kg)
and 16 lbs (7 kg) for
each drawer panel.
CABINETRY APPLICATIONS
FRAMED CABINETRY
Integrated refrigeration is compatible with virtually any style and look of cabinetry. The models
can be used with framed as well as frameless
cabinets. Because of the precise application and
the look you may want to achieve, there are
important questions you need to answer before
ordering panels for the doors/drawers. As you
look at styles of cabinets, keep some important
facts in mind:
Framed cabinetry applications present you with
different questions to address. The illustrations
below show common applications of framed
cabinetry. These are not meant to be the only
alternatives, but are suggestions from designers
around the country. Also refer to the full-scale
illustrations at the end of this section for
specifics on door openings.
NOTE: In the illustrations below, the first width
dimension shown is for 27" (686) wide units
and the second dimension is for 36" (914) wide
units.
IMPORTANT NOTE: The depth of each Integrated model is 24" (610) from the front of the
unit to its back. You must allow for the thickness of the panel you are applying when
planning for the finished rough opening depth if
you want the front panel to be flush with
surrounding cabinetry. You must move the unit
back into drywall or bring the cabinets forward
to achieve a flush fit.
The height of the door panel can grow beyond
45 3/8" (1153) and exceed the 80" (2032) overall
height as long as you stay below the recommended door panel weight limit.
The toe kick clearance can vary with the height
of the lower drawer panel; the maximum panel
height is 16 11/16" (424). You must keep a
minimum space of 4" (102) clear below the
bottom edge of the lower drawer panel so the
unit can be properly vented.
We recommend using D-style handles. For the
cabinet door, handles must be located near the
edge of the panel opposite the hinge, centered
top to bottom. Locate handles in the top center
area of the drawer panels.
IMPORTANT NOTE: The inside edges of the
rough opening, as well as the sides and a
portion of the backside of the decorative panels
will need to be finished, as they will be exposed
when the doors are open.
CABINET
DOOR
1/8" (10)
REVEAL
27
OR
Traditional frame – full overlay
(top view)
36
(914)
CABINET
FRAME
CABINET
DOOR
24
SUB-ZERO
UNIT
(610)
TO WALL
DOOR PANEL
(686)
40
24
SUB-ZERO
UNIT
CABINET
FRAME
24
SUB-ZERO
UNIT
(610)
TO WALL
(610)
TO WALL
CABINET
FRAME
1/8" (10)
REVEAL
DOOR PANEL
27
(686)
OR
CABINET
DOOR
1/8" (10)
REVEAL
DOOR PANEL
36
27
(914)
(686)
Traditional frame – standard overlay
(top view)
OR
36
(914)
Traditional frame – 3/8" (10) offset
(top view)
INTEGRATED REFRIGERATION
FRAMED CABINETRY –
BEADED INSET APPLICATION
The illustration below shows a 27" (686) wide
Integrated base or tall unit installed within a
framed cabinetry, beaded inset application.
Review, giving particular attention to the overall
panel specifications. Also refer to the full-scale
illustrations at the end of this section for
specifics on door openings.
27" (686)
WIDE MODELS
24"
Installation of a
27" (686) wide
Integrated base or
tall unit within
framed cabinetry.
(610)
SUB-ZERO
UNIT
CABINET DOOR
TO WALL
DOOR PANEL
A
*Dimensions may vary.
A
TOP VIEW
A) ALL REVEALS ARE 1/8" (3)
B) DRAWER RAILS ARE ATTACHED TO DRAWER FRONTS
C) BOTTOM RAIL MUST BE REMOVABLE
27"
(686)
*DIMENSIONS MAY VARY
26 3/4" (679)
PANEL WIDTH
Dimensions are based
on a 1/8" (3) reveal. A
reveal of up to 1/4" (6)
is possible, but panel
dimensions need to be
adjusted accordingly.
11/2"
(38)
47 7/8"
84"
(1216)
(2624)
SHADED AREA
INDICATES STATIONARY
STYLES AND RAILS
80"*
(2032)
A
B
13 9/16"
(345)
A
B
341/2"
(876)*
15 1/16"
11/2"
(383)
(38)
A
C
4"*
27"
11/2"
(686)
(38)
11/2"
(38)
FRONT VIEW
(102)
4" (102)
24"
(610)
SIDE VIEW
Dimensions are in
inches with millimeters in parentheses
unless otherwise
specified.
41
INTEGRATED REFRIGERATION
FRAMED CABINETRY –
BEADED INSET APPLICATION
The illustration below shows 36" (914) wide
Integrated tall unit installed within a framed cabinetry, beaded inset application. Review, giving
particular attention to the overall panel specifications. Also refer to the full-scale illustrations at
the end of this section for specifics on door
openings.
36" (914)
WIDE MODELS
Installation of a
36" (914) wide
Integrated tall unit
within framed
cabinetry.
24"
(610)
SUB-ZERO
UNIT
CABINET DOOR
DOOR PANEL
*Dimensions may vary.
Dimensions are based
on a 1/8" (3) reveal. A
reveal of up to 1/4" (6)
is possible, but panel
dimensions need to be
adjusted accordingly.
TO WALL
A
A
A) ALL REVEALS ARE 1/8" (3)
B) DRAWER RAILS ARE ATTACHED TO DRAWER FRONTS
C) BOTTOM RAIL MUST BE REMOVABLE
36"
TOP VIEW
(914)
*DIMENSIONS MAY VARY
35 3/4" (908)
PANEL WIDTH
11/2"
(38)
47 7/8"
84"
(1216)
(2624)
SHADED AREA
INDICATES STATIONARY
STYLES AND RAILS
80"*
(2032)
A
B
13 9/16"
(345)
A
B
341/2"
(876)*
15 1/16"
11/2"
(38)
(383)
A
C
4"*
36"
11/2"
Dimensions in
parentheses are in
millimeters unless
otherwise specified.
42
(914)
(38)
11/2"
(38)
FRONT VIEW
(102)
4" (102)
24"
(610)
SIDE VIEW
INTEGRATED REFRIGERATION
FRAMELESS CABINETRY
26 3/4"* (679)
24"
PANEL WIDTH
The illustrations show hypothetical installations of Integrated
base or tall units within frameless
cabinetry. Review, giving particular attention to the overall panel
specifications. Also refer to the
full-scale illustrations at the end
of this section for specifics on
door openings.
(610)
A
45 3/8"
(1153)
80"*
(2032)
27" (686)
WIDE MODELS
79 7/8"*
(2029)
Installation of a
27" (686) wide
Integrated base or
tall unit within
frameless cabinetry.
A
13 9/16"
(345)
*Dimensions may vary.
A
341/2"
(876)*
Dimensions are based
on a 1/8" (3) reveal. A
reveal of up to 1/4" (6)
is possible, but panel
dimensions need to be
adjusted accordingly.
16 11/16"*
(424)
4"*
(102)
27"
(686)
TOE KICK
SIDE VIEW
FINISHED OPENING
A) ALL REVEALS ARE 1/8" (3)
*DIMENSIONS MAY VARY
36" (914)
WIDE MODELS
35 3/4"* (908)
24"
PANEL WIDTH
(610)
Installation of a
36" (914) wide
Integrated tall unit
within frameless
cabinetry.
A
*Dimensions may vary.
Dimensions are based
on a 1/8" (3) reveal. A
reveal of up to 1/4" (6)
is possible, but panel
dimensions need to be
adjusted accordingly.
45 3/8"
(1153)
80"*
(2032)
79 7/8"*
(2029)
A
13 9/16"
(345)
A
341/2"
(876)*
16 11/16"*
(424)
4"*
(102)
36"
TOE KICK
(914)
SIDE VIEW
FINISHED OPENING
A) ALL REVEALS ARE 1/8" (3)
*DIMENSIONS MAY VARY
To install integrated
panels, see the
detailed procedures
outlined in the
Sub-Zero Integrated
Installation
Instructions.
43
INTEGRATED REFRIGERATION
PANEL CONSIDERATIONS
The illustrations below provide panel width
dimensions for installation of a single tall unit,
27" (686) and 36" (914) wide models.
Illustrations on the following page provide panel
width dimensions for installing two tall units
side by side, 27" (686) wide models and 36"
(914) wide models.
IMPORTANT NOTE: The depth of each
Integrated model is 24" (610) from the front of
the unit to its back. You must allow for the
thickness of the panel you are applying when
planning for the finished rough opening depth if
you want the front panel to be flush with
surrounding cabinetry. You may have to move
the unit back into drywall or bring the cabinets
forward to achieve a flush fit.
PANEL
REQUIREMENTS
Door and drawer
panels must be a
minimum of 5/8" (16)
thick.
The door panel
cannot exceed 40 lbs
(18 kg) and each
drawer panel must
not exceed 12 lbs
(5 kg) for 27" (686)
wide units. For 36"
(914) wide units, the
door panel weight
limit is 53 lbs (24 kg)
and 16 lbs (7 kg) for
each drawer panel.
27" (686)
WIDE MODELS
27
Panel width dimensions for installation
of a 27" (686) wide
tall unit.
* 1 (3) min
8
REVEAL
(686)
* 1 (3) min
8
REVEAL
26 43 (679)
3
4 (19) PANEL
Dimensions are based
on a 1/8" (3) reveal. A
reveal of up to 1/4" (6)
is possible, but panel
dimensions need to be
adjusted accordingly.
25 87 (657)
25
(635)
CABINETRY
OR SIDE
PANEL
APPLIANCE
DOOR WIDTH
24
(610)
TO BACK
OF UNIT
25
(635)
CABINETRY
OR SIDE
PANEL
SUB-ZERO
UNIT
*SUBTRACT PANEL WIDTH FROM CABINETRY OPENING TO DETERMINE ACTUAL WIDTH OF REVEAL
36" (914)
WIDE MODELS
36
Panel width dimensions for installation
of a 36" (914) wide
tall unit.
* 1 (3) min
8
REVEAL
(914)
* 1 (3) min
8
REVEAL
35 43 (908)
3
4 (19) PANEL
Dimensions are based
on a 1/8" (3) reveal. A
reveal of up to 1/4" (6)
is possible, but panel
dimensions need to be
adjusted accordingly.
34 87 (886)
25
(635)
CABINETRY
OR SIDE
PANEL
24
(610)
APPLIANCE
DOOR WIDTH
TO BACK
OF UNIT
25
(635)
CABINETRY
OR SIDE
PANEL
SUB-ZERO
UNIT
*SUBTRACT PANEL WIDTH FROM CABINETRY OPENING TO DETERMINE ACTUAL WIDTH OF REVEAL
Dimensions are in
inches with millimeters in parentheses
unless otherwise
specified.
44
INTEGRATED REFRIGERATION
PANEL CONSIDERATIONS
As the reveal between cabinets and the
Integrated unit decreases, the potential
exists for severe finger pinching or crushing
if a hand or fingers are placed in the
opening when the door is closing.
When 3/4" (19) or thicker panels are used
and a reveal less than 1/4" (6) is maintained,
the door panels may cause damage to the
Sub-Zero unit when the door is open at the
maximum 105˚ stop. You should use the
built-in 90˚ stop to prevent damage.
27" (686)
WIDE MODELS
54 (1372)
* 1 (3) min
8
REVEAL
13
(681)
26 16
13
(681)
26 16
* 1 (3) min
8
REVEAL
3
4 (19) PANEL
* 1 (3) min
8
REVEAL
Panel width dimensions for installation
of two 27" (686)
wide tall units side
by side.
Dimensions are based
on a 1/8" (3) reveal. A
reveal of up to 1/4" (6)
is possible, but panel
dimensions need to be
adjusted accordingly.
3
4 (19) PANEL
25
25
(635)
(635)
CABINETRY
OR SIDE
PANEL
CABINETRY
OR SIDE
PANEL
24
(610)
DOOR
DOOR
SUB-ZERO
UNIT
SUB-ZERO
UNIT
TO BACK
OF UNIT
*SUBTRACT PANEL WIDTH FROM CABINETRY OPENING TO DETERMINE ACTUAL WIDTH OF REVEAL
36" (914)
WIDE MODELS
72 (1829)
* 1 (3) min
8
REVEAL
Panel width dimensions for installation
of two 36" (914)
wide tall units side
by side.
25
25
(635)
(635)
Dimensions are based
on a 1/8" (3) reveal. A
reveal of up to 1/4" (6)
is possible, but panel
dimensions need to be
adjusted accordingly.
* 1 (3) min
8
REVEAL
13
(910)
35 16
13
(910)
35 16
* 1 (3) min
8
REVEAL
3
4 (19) PANEL
CABINETRY
OR SIDE
PANEL
24
(610)
3
4 (19) PANEL
DOOR
DOOR
SUB-ZERO
UNIT
SUB-ZERO
UNIT
TO BACK
OF UNIT
CABINETRY
OR SIDE
PANEL
*SUBTRACT PANEL WIDTH FROM CABINETRY OPENING TO DETERMINE ACTUAL WIDTH OF REVEAL
To install integrated
panels, see the
detailed procedures
outlined in the
Sub-Zero Integrated
Installation
Instructions.
45
INTEGRATED REFRIGERATION
INSTALLATION OPTIONS
The illustrations show some typical installations
and their dimension considerations. The depth
dimension in the illustrations may vary depending on cabinet styles, treatment of countertops
or other design options.
ACCESSORIES
Optional accessories
are available
through your
Sub-Zero dealer. To
obtain local dealer
information, visit the
Showroom Locator
section of our
website,
subzero.com.
IMPORTANT NOTE: The depth of each
Integrated model is 24" (610) from the front of
the unit to its back. Your design may necessitate
moving the unit back or cabinets forward to
achieve a flush fit. This will require a minimum
rough opening depth of 25" (635). Refer to the
illustrations.
CABINETS
25
(635)
27
(686)
OR
36
(914)
TOP VIEW
Installation without side panels
NOTE: In the Installation Options illustrations,
the first width dimension shown is for 27" (686)
wide units and the second dimension is for 36"
(914) wide units.
CABINETS
25
(635)
DUAL INSTALLATIONS
If two or more Integrated models are installed
side by side where there is 2" (51) or less of
space between the units, a heater kit is recommended—TTDUAL for two tall units installed side
by side and BBDUAL for two base units or a
base unit and a tall unit installed side by side.
These optional components are available through
your Sub-Zero dealer.
27
(686)
OR
36
(914)
5
MINIMUM 8 (16) SIDE PANELS
Installation with side panels
CABINETS
25
(635)
54
72
(1372)))OR (1829))
)
TOP VIEW
Installation of two units side by side
CABINETS
25
(635)
27
(686)
OR
36
(914)
5
MINIMUM 8 (16) SIDE PANELS
Dimensions are in
inches with millimeters in parentheses
unless otherwise
specified.
46
Installation at end of run
INTEGRATED REFRIGERATION
DOOR PANEL HEIGHT
TOE KICK CLEARANCE
The height of the door panel can grow beyond
45 3/8" (1153) and exceed the 80" (2032) overall
height, as long as you stay below the recommended door panel weight limit.
The toe kick clearance can vary with the height
of the lower drawer panel; the maximum panel
height is 16 11/16" (424).
The top illustration shows how the panel may
grow and what you need to consider doing to
finish the area in back of the door panel.
IMPORTANT NOTE: The valance you use to
finish the area behind the door panel must stay
behind the front plane of the finished molding.
IMPORTANT NOTE: You must keep a minimum
space of 4" (102) clear below the bottom edge
of the lower drawer panel so the unit can be
properly vented. In addition, any decorative base
molding must be removable for possible servicing and cleaning of the condenser.
The bottom illustration shows the area below
the lower drawer where the operating mechanical equipment of the Integrated unit is housed.
UPPER VALANCE
25
Tall Models
(635)
TO WALL
1 21 (38)
DECORATIVE VALANCE
CANNOT EXTEND BEYOND
THE FRONT OF THIS PLANE
The depth of each
Integrated model is
24" (610) from the
front of the unit to its
back. Your design
may necessitate
moving the unit back
or cabinets forward to
achieve a flush fit.
This will require a
minimum rough
opening depth of 25"
(635).
DECORATIVE VALANCE
1
8
(3)
PANEL
REQUIREMENTS
Door and drawer
panels must be a
minimum of 5/8" (16)
thick.
The door panel
cannot exceed 40 lbs
(18 kg) and each
drawer panel must
not exceed 12 lbs
(5 kg) for 27" (686)
wide units. For 36"
(914) wide units, the
door panel weight
limit is 53 lbs (24 kg)
and 16 lbs (7 kg) for
each drawer panel.
REMOVABLE MOLDING
BY SUB-ZERO
45 83
(1153)
TO
BOTTOM
OF
DOOR
PANEL
TOP HINGE
80*
(2032)
TO
FLOOR
*FINISHED HEIGHT OF 80" (2032) IS TO TOP OF SUB-ZERO MOLDING
K I C K P L AT E A R E A
Base and Tall Models
9
1016
(268)
PANEL
1
2
(13)
1611
16
(424)
PANEL
11
9 16
(246)
10
(254)
OPTIONAL
BASE MOLDING MUST
BE REMOVABLE
4
25
(102)
(635) TO WALL
2 85 TO 4
(67)
(102)
FLOOR
47
INTEGRATED REFRIGERATION
FRAMED CABINETRY
IMPORTANT NOTE: The depth of each
Integrated model is 24" (610) from the
front of the unit to its back. Your
design may necessitate moving the
unit back or cabinets forward to
achieve a flush fit.
DOOR CLOSED
SUB-ZERO
DOOR
105˚ MAXIMUM
DOOR OPENING
Full-scale (top view)
1/4 scale (top view)
24
(610)
TO BACK
OF UNIT
LINE OF INTERFERENCE*
LINE OF INTERFERENCE*
AT MAXIMUM DOOR OPENING
MOUNTING BRACKET SCREW
1 (3)
MIN.
8
REVEAL
PANEL
3
4 (19)
25 87 (657) DOOR WIDTH FOR 27" (686) MODELS
34 87 (886) DOOR WIDTH FOR 36" (914) MODELS
SUB-ZERO DOOR
24
(610)
TO BACK
OF UNIT
LINE OF INTERFERENCE*
SIDE MOLDING AND
INSTALLATION HARDWARE
PROVIDED BY SUB-ZERO
FLUSH
FURNITURE
FINISH
48
*If the panel is thicker than 3/4" (19), it is
recommended that you utilize the built-in
90˚ door stop to prevent damage to the
panel and face frame.
INTEGRATED REFRIGERATION
FRAMELESS CABINETRY
IMPORTANT NOTE: The depth of each
Integrated model is 24" (610) from the
front of the unit to its back. Your
design may necessitate moving the
unit back or cabinets forward to
achieve a flush fit.
SUB-ZERO DOOR
3/4" (19) DOOR
COUNTERTOP
PANEL
SIDE PANEL
105˚ MAXIMUM
DOOR OPENING
DOOR CLOSED
1/4 scale (top view)
Full-scale (top view)
Adjacent side panel and
countertop application.
24
(610)
TO
WALL
1 (3)
MIN.
8
LINE OF INTERFERENCE*
LINE OF INTERFERENCE*
AT MAXIMUM DOOR OPENING
REVEAL
MOUNTING BRACKET SCREW
3
4 (19)
PANEL
25 87 (657) DOOR WIDTH FOR 27" (686) MODELS
34 87 (886) DOOR WIDTH FOR 36" (914) MODELS
SUB-ZERO DOOR
24
(610)
TO BACK
OF UNIT
LINE OF INTERFERENCE*
SIDE MOLDING AND
INSTALLATION HARDWARE
PROVIDED BY SUB-ZERO
Dimensions are in
inches with millimeters in parentheses
unless otherwise
specified.
*If the panel is thicker than 3/4" (19), it is
recommended that you utilize the built-in
90˚ door stop to prevent damage to the
panel and face frame.
49
WINE STORAGE
WINE STORAGE
UNDERCOUNTER
15 1/8"
237/8"
241/4"
(384)
(606)
(616)
34 1/16"
34"
343/16"
(865)
(864)
(868)
MODEL 315W
MODEL 424
MODEL 424FS
Built-In
Built-In
Free-Standing
ALL WINE STORAGE
30"
(762)
27"
(686)
Sub-Zero‘s innovative addition to its complete
line of residential refrigeration is wine storage
equipment—the ultimate in beauty, engineering,
and attention to detail. From the exterior and the
smooth lines of the free-standing Model 424FS
classic stainless steel to the ability to use wood
on the Built-In and Integrated models, each unit
is beautiful.
With the exception of the free-standing Model
424FS, each model is available in three stainless
steel finishes and will have the capability of
having wood panels applied to the doors. With
the Model 427R, you can also apply the wood to
the drawers.
The new Model 315W, a single-zone Wine
Storage unit, comes only with a glass door and
can be ordered as an overlay or classic stainless
steel unit.
80"
84"
(2032)
(2134)
The free-standing Model 424FS does not require
any panels or surrounding cabinetry; it comes
with classic stainless steel exterior.
MODEL 427
MODEL 430
Integrated
Built-In
W I N E S T O R A G E | R E F R I G E R AT O R
27"
(686)
80"
(2032)
MODEL 427R
Integrated
With the installation of a harness kit,
Wine Storage models, except Model 315W,
are Star-K compliant to meet strict religious
regulations in conjunction with specific
instructions found on www.star-k.org.
For details about the harness kit, contact
your Sub-Zero dealer.
The illustrations represent the full line of
Wine Storage models. The Model 424FS
free-standing unit comes with a classic
stainless steel exterior.
Dimensions in
parentheses are in
millimeters unless
otherwise specified.
50
Comprehensive installation instructions are
shipped with each model. Refer to those
instructions in preparing and installing all
Sub-Zero products. The instructions can also
be found on our website, subzero.com.
All models will be shipped with glass doors as
standard equipment. The glass doors allow one
to see the wine that is being stored. Optional
solid doors and high altitude glass doors will be
treated as special orders and must be ordered 90
days before you expect delivery. Model 315W
cannot be ordered with a solid door.
Stainless steel models will be shipped with
tubular stainless steel handles, while the overlay
models will come with no handle hardware.
Optional stainless steel panels and handles for
Models 427 and 427R are offered in the classic,
platinum and carbon stainless steel finishes and
are ordered and shipped as sales accessories.
The stainless steel Models 424 and 430 must be
ordered in one of three stainless steel finishes of
classic, platinum and carbon.
Optional handles are available for all models
except the framed and stainless steel Model
430. The framed Model 430 will come with an
extruded handle identical in design to our Built-In
models.
Standard grille assemblies for the Model 430 will
be provided in 1" (25) increments from 10" (254)
to 15" (381). The standard height will be 11"
(279). The framed model will have a louvered
grille, the stainless steel model will feature a
heavy-duty grille, and the overlay model will
have the panel grille, which accepts decorative
panel inserts.
For information regarding specific Wine Storage
models, refer to the illustrations in this section.
WINE STORAGE
FEATURES AND OPTIONS
When looking for wine storage, you no longer
have to think only about an undercounter application. Sub-Zero offers you complete flexibility
from the perspective of design applications and
storage capabilities.
Model 315W, a single-zone Wine Storage unit,
comes as an overlay or classic stainless steel
unit and is offered only with a glass door.
Model 424 comes in the overlay and stainless
steel door panel configurations. Model 424FS
(free-standing) is identical to the Model 424 but
with classic stainless steel exterior and is
designed to be attractive in a stand-alone
setting. Models 424 and 424FS are available in
either a glass or solid door model.
Models 427 and 427R are offered as integrated
or stainless steel and are available in either a
glass or solid door model. Optional stainless
steel panels and handles are offered in classic,
platinum and carbon stainless steel finishes at
the 80" (2032) height, and only classic stainless
steel at the 84" (2134) height. Stainless steel
panels are available as sales accessories.
Model 430 comes in the framed, overlay and
stainless steel options and is available in either a
glass or solid door model. Stainless steel Model
430 must be ordered in one of the stainless steel
finishes of classic, platinum and carbon.
Built-In Look. Sub-Zero offers you a host of
design alternatives to choose from when selecting the look you want. Wood or stainless steel,
framed, overlay or integrated.
Dual Zone System*. With the exception of the
single-zone Model 315W, all Wine Storage
models allow you to have precise temperature
control within one degree of your pre-set
temperature in each of the two wine compartments.
Dual Refrigeration System*. In a similar fashion
to our Built-In, each Wine Storage model has
dual refrigeration so your client will have
specific, individual temperature control of the
two wine compartments.
Electronic Controls*. Microprocessor offers
touch pad controls that are easy to understand
and that set the temperatures accurately.
Display Shelf*. This beautiful shelf offers your
clients the opportunity to display those prize
bottles or magnums of wine in their collection. It
is illuminated with discreet lighting mounted in
the control panel. (Not available with Models
315W, 424 and 424FS.)
Storage Shelves. The sturdy, rustproof wire
shelves can easily accommodate standard 750
ml bottles, half bottles, as well as magnums. All
the shelves are finished off with a natural cherry
wood facing. In addition, all shelves will enable
you to be sure the wine is stored properly and
that the corks are in contact with the bottles‘
contents.
Roller Assembly. All shelves have a roller
assembly, which enables you to have a threequarter extension for easy access to all bottles
of stored wine.
Service Alert*. An indicator light will let you
know if service may be necessary.
Home Alarm*. Wiring connections give you the
option of hooking the Wine Storage unit up to
your home security system.
SUB-ZERO
WARRANTY
Sub-Zero products
are covered by a
two, five and twelve
year residential
warranty (exclusions
apply). See warranty
details at the end of
this guide.
Discreet Lighting. Our soft low-wattage lighting
is independent of door opening.
Correct Temperature*. The range of each
temperature zone is 38˚F (3˚C) to 65˚F (18˚C), and
your set temperature is digitally displayed in the
control panel.
Humidity. Proper humidity is maintained
throughout the entire unit.
UV Protection. The tinted glass minimizes the
amount of ultraviolet light entering the unit.
Lock*. A lock will be offered as an option for all
Wine Storage models. The lock is offered as a
sales accessory and should be ordered through
your Sub-Zero dealer. Special planning is necessary when ordering locks for Models 427 and
427R, refer to page 61 for details.
Solid Door*. If you would like to order a model
without glass, you have that option. This will be
treated as a special order and must be ordered
90 days before you expect delivery.
High Altitude Glass. For installations above
5,000' (1524 m) in elevation, we offer the high
altitude glass as a special order. The high
altitude glass door is standard on Model 315W.
Tight Seal. Magnetic gaskets around the doors
give extra-tight seals.
Kickplate. The solid, adjustable kickplate gives a
true built-in look and conforms to American
Institute of Architects standards.
Front Venting. All Sub-Zero Wine Storage
models are designed for mechanical system
airflow at the front of the appliance. Decorative
panels must not cover louvered surfaces or
prevent removal of louvered components.
*Not available with Model 315W.
51
WINE STORAGE
MODEL 315W
MODEL 424
MODEL 424FS
UNDERCOUNTER
B U I LT- I N
UNDERCOUNTER
B U I LT- I N
UNDERCOUNTER
FREE-STANDING
MODEL OPTIONS
MODEL OPTIONS
MODEL OPTIONS
Overlay Design
315W/O
Overlay Design
424/O
Full-View Glass Door (standard)
Classic Stainless Steel
315W/S
Classic Stainless Steel
424/S
High Altitude Glass Door**
Platinum Stainless Steel 424/P
Carbon Stainless Steel
S P E C I F I C AT I O N S
Solid Door
424/B
Overall Width
15 1/8" (384)
Full-View Glass Door (standard)
S P E C I F I C AT I O N S
Overall Height
34 1/16" (865)
High Altitude Glass Door**
Overall Width
24 1/4" (616)
Overall Depth
24" (610)
Solid Door
Overall Height
34 3/16" (868)
Wine Storage Capacity
26 bottles*
Overall Depth
24 5/8" (625)
Min Height Required
34 1/16"
Wine Storage Capacity
46 bottles*
Door Swing Clearance
16 5/8" (422)
Overall Width
23 7/8" (606)
Door Swing Clearance
25 3/8" (645)
Specify Door Swing
LH or RH
Overall Height
34" (864)
Specify Door Swing
LH or RH
Shipping Wt (O)
114 lbs (52 kg)
Overall Depth
24" (610)
Shipping Wt
220 lbs (100 kg)
Shipping Wt (S)
118 lbs (54 kg)
Wine Storage Capacity
46 bottles*
Min Height Required
34 1/4" (870)
F E AT U R E S
F E AT U R E S
Door Swing Clearance
25 3/8" (645)
2 Temperature Zones
1 Temperature Zone
Specify Door Swing
LH or RH
8 (750 ml) Bottles per Standard Shelf
4 (750 ml) Bottles per Standard Shelf
Shipping Wt (glass)
190 lbs (86 kg)
2 Top Zone Shelves (16 bottles*)
6 Standard Shelves (24 bottles*)
Shipping Wt
(glass /S/P/B)
195 lbs (88 kg)
Shipping Wt (solid)
185 lbs (84 kg)
(865)
1 Fixed Bottle Holder (2 bottles*)
Full-View High Altitude Glass Door
S P E C I F I C AT I O N S
3 Bottom Zone Shelves (24 bottles*)
1 Fixed Bottle Holder (6 bottles*)
Full-View Glass Door
Classic Stainless Steel Exterior
and Door Frame
F E AT U R E S
2 Temperature Zones
8 (750 ml) Bottles per Standard Shelf
2 Top Zone Shelves (16 bottles*)
3 Bottom Zone Shelves (24 bottles*)
1 Fixed Bottle Holder (6 bottles*)
Full-View Glass Door
MODEL 315W
MODEL 424
*750 ml bottles.
ACCESSORIES
**High altitude glass doors are for
installations at or above 5,000' (1524 m) in
elevation and will be treated as a special
order. Please allow 90 days for delivery.
When ordering, add an (HA) before the (G) to
obtain the correct model number.
***Optional stainless steel panels and
handles are ordered and shipped as sales
accessories. For additional information on
panel and handle sizes and applications,
check our website, subzero.com.
52
MODEL 424FS
Contact your Sub-Zero Dealer
Classic stainless steel front
panels—platinum and carbon
available in certain sizes
(Models 427 and 427R)*
Tubular handles in classic,
platinum and carbon stainless
steel
Front, side and grille panels
(framed Model 430)*
Louvered, panel or stainless
steel grilles in varied heights
(Model 430)*
UL-approved door lock kit
Dual installation heater kit
(Models 427 and 427R)*
*Accessory is available only for
models listed.
WINE STORAGE
MODEL 427
MODEL 430
MODEL 427R
ALL WINE STORAGE
ALL WINE STORAGE
W I N E S T O R A G E | R E F R I G E R AT O R
MODEL OPTIONS
MODEL OPTIONS
Full-View Glass Door (standard)
Framed Design
430/F
Full-View Glass Door (standard)
High Altitude Glass Door**
Overlay Design
430/O
High Altitude Glass Door**
Solid Door
Classic Stainless Steel
430/S
Solid Door
MODEL OPTIONS
Platinum Stainless Steel 430/P
Carbon Stainless Steel
S P E C I F I C AT I O N S
430/B
S P E C I F I C AT I O N S
Overall Width
27" (686)
Full-View Glass Door (standard)
Overall Width
27" (686)
Overall Height
80" (2032)
High Altitude Glass Door**
Overall Height
80" (2032)
Overall Depth
24" (610)
Solid Door
Overall Depth
24" (610)
Wine Storage Capacity
132 bottles*
Wine Storage Capacity
78 bottles*
Min Height Required
79 1/2" (2019)
S P E C I F I C AT I O N S
Refrigerator Capacity
5.3 cu ft (150 L)
Door Swing Clearance
25 1/2" (648)
Overall Width
30" (762)
Min Height Required
79 1/2" (2019)
Specify Door Swing
LH or RH
Overall Height
84" (2134)
Door Swing Clearance
25 1/2" (648)
Shipping Wt (glass)
395 lbs (179 kg)
Overall Depth
24" (610)
Specify Door Swing
LH or RH
Shipping Wt (solid)
386 lbs (175 kg)
Wine Storage Capacity
147 bottles*
Drawer Clearance
19 1/2" (495)
Min Height Required
83" (2108)
Shipping Wt (glass)
410 lbs (186 kg)
F E AT U R E S
Door Swing Clearance
30 1/8" (765)
Shipping Wt (solid)
406 lbs (184 kg)
2 Temperature Zones
Specify Door Swing
LH or RH
9 (750 ml) Bottles per Standard Shelf
Shipping Wt (glass)
435 lbs (197 kg)
5 Top Zone Shelves (45 bottles*)
Shipping Wt
(glass /S/P/B)
445 lbs (202 kg)
Shipping Wt (solid)
412 lbs (187 kg)
9 Bottom Zone Shelves (81 bottles*)
1 Display Shelf (6 bottles*)
3 Temperature Zones
Full-View Glass Door
PANEL OPTIONS
Integrated
Classic, platinum or carbon stainless
steel finish (includes handle)***
2 Refrigerated Drawers
9 (750 ml) Bottles per Standard Shelf
6 Top Zone Shelves (54 bottles*)
F E AT U R E S
2 Bottom Zone Shelves (18 bottles*)
2 Temperature Zones
1 Display Shelf (6 bottles*)
10 (750 ml) Bottles per Standard Shelf
Full-View Glass Door
5 Top Zone Shelves (50 bottles*)
9 Bottom Zone Shelves (90 bottles*)
1 Display Shelf (7 bottles*)
Full-View Glass Door
MODEL 427
F E AT U R E S
MODEL 430
PANEL OPTIONS
Integrated
Classic, platinum or carbon stainless
steel finish (includes handles)***
MODEL 427R
NOTE: For Wine Storage standard glass door
models, add (G) to the model number and for
solid door models, add (S) to the model
number (example 424G or 424S). The exception is Model 315W which is available as a
glass door model only.
53
WINE STORAGE
ACCESSORIES
Optional accessories
are available
through your
Sub-Zero dealer. To
obtain local dealer
information, visit the
Showroom Locator
section of our
website,
subzero.com.
PLANNING INFORMATION
ELECTRICAL REQUIREMENTS
Review the Overall Dimensions and Installation
Specifications illustrations for your Wine Storage
model on the following pages. These specifications cover all the details you need to know
about space allocation and placement of electrical, whether the models are framed, overlay,
stainless steel or integrated.
A 115 V AC, 60 Hz, 15 amp circuit breaker and
electrical supply are required. A separate circuit
servicing only this appliance is required.
All Wine Storage models must be installed so
that the door can open a minimum of 90˚ or you
will have problems pulling the wine shelves out.
Refer to the door clearance and door swing
information.
For corner installations, you need allow for a
minimum 3" (76) filler so the door can open to
90˚. If you are using larger handle hardware, you
will also need to take that into account.
For a maximum 90˚ door opening, use the door
stop built into the hinge system of Model 427.
An optional 90˚ door stop kit for Model 430 is
available from your Sub-Zero dealer.
If you will be connecting the unit to a home
security system, you must allow a minimum of
36" (914) of the system‘s wiring to be routed in
the electrical area designated for your model.
IMPORTANT NOTE: The anti-tip bracket must be
installed to prevent the unit from tipping
forward.
DUAL INSTALLATIONS
If you are installing a Wine Storage unit next to
an existing Sub-Zero unit, you may have to allow
for a filler strip.
If you are installing a Model 427 or 427R Wine
Storage unit next to an existing Integrated
Sub-Zero unit, with 2" (51) or less between the
units, an optional heater kit (BBDUAL or
TTDUAL) will need to be installed to prevent
moisture from forming between the units. This
optional kit is available through your Sub-Zero
dealer.
Dimensions in
parentheses are in
millimeters unless
otherwise specified.
54
All Sub-Zero Wine Storage models are equipped
with a power supply cord with a 3-prong grounding plug, which must be plugged into a mating
3-prong grounding-type wall receptacle. Follow
the National Electrical Code and local codes and
ordinances when installing the receptacle. Refer
to the Installation Specifications illustrations on
the following pages for electrical placement for
your model.
IMPORTANT NOTE: A ground fault circuit
interrupter (GFCI) is not recommended and may
cause interruption of operation.
WINE STORAGE
OVERALL DIMENSIONS
Undercounter Wine Storage
23 78
(606)
1
23 2 (597) DOOR FRAME
15 1/8"
(384)
34 1/16"
30 1/16"
(865)
(764)
10 43
24 14
23 81 (587)
24 85 (625)
(616)
(CABINET DIMENSION)
(CABINET DIMENSION)
3
*3416
3
*34
(273)
CENTERED
VERTICALLY
(864)
30 16
(868)
(767)
DOOR
FRAME
4
(102)
4" (102)
4
FRONT VIEW
SIDE VIEW
(102)
TOE KICK
FRONT VIEW
*1/2" (13) +_ ADJUSTMENT IN LEVELING LEGS
*1/2" (13) +_ ADJUSTMENT IN LEVELING LEGS
MODEL 315W
MODEL 424
MODEL 424FS
Built-In
Built-In
Free-Standing
FRONT VIEW
Width
15 1/8" (384)
Width
23 7/8" (606)
Width
24 1/4" (616)
Height 34 1/16" (865)
Height 34" (864)
Height 34 3/16" (868)
Depth
Depth
Depth
24" (610)
24" (610)
24 5/8" (625)
SIDE VIEW
UNDERCOUNTER
Model 315W
Built-In
Model 424
Built-In
Model 424FS
Free-Standing
Note the location of pre-drilled
holes for optional handle hardware.
I N S TA L L AT I O N S P E C I F I C AT I O N S
Undercounter Models
24"
(610)
ROUGH
OPENING
DEPTH
Model 315W
A) Rough Opening Width
15 1/4" (387)
B) Rough Opening Height 34 1/2" (876)
C) Min Door Clearance
16 5/8" (422)
D) Min Clearance at 90˚
17 1/4" (438)
90˚
C
TOP VIEW
Model 424
A) Rough Opening Width
A
D
ROUGH OPENING
WIDTH
24" (610)
B) Rough Opening Height 34 1/2" (876)
C) Min Door Clearance
25 3/8" (644)
D) Min Clearance at 90˚
26" (660)
MODEL 315W
LOCATE ELECTRICAL
ANYWHERE ON
BACK WALL
C) Min Door Clearance
25 3/8" (644)
D) Min Clearance at 90˚
26" (660)
MODELS 424 | 424FS
LOCATE ELECTRICAL
WITHIN SHADED AREA
Model 424FS*
41/2"
151/2"
E
21/2"
(64)
Door swing clearances are based on
stainless steel door and handle dimensions.
(114)
(394)
*Free-standing Model 424FS requires no
surrounding cabinetry.
Dimensions are for finished rough openings.
B
ROUGH
OPENING
HEIGHT TO
FINISHED
FLOORING
FRONT VIEW
Refer to installation
instructions shipped
with each Wolf
product for detailed
specifications.
55
WINE STORAGE
OVERALL DIMENSIONS
All Wine Storage – Model 427
Wine Storage | Refrigerator – Model 427R
24
27
24
27
(686)
(610)
(686)
(610)
26 81 (664) DOOR FRAME
14 (356)
(UNIT DIMENSION)
26 81 (664) DOOR FRAME
14 (356)
(UNIT DIMENSION)
I N T E G R AT E D
13
16
(20)
13
16
(20)
Model 427
All Wine Storage
44 87
(1139)
Model 427R
Wine Storage |
Refrigerator
80
(273)
CENTERED
VERTICALLY
(2032)
80
70167
10 43
OVERALL
DIMENSIONS
DOOR
FRAME
WITH
HINGES
10 43
*78 85
(273)
CENTERED
VERTICALLY
(1997)
(2032)
(1789)
DOOR
FRAME
WITH
HINGES
*78 85
3
8
(9)
(1997)
Model 427 | 427R
Width
1
2
(13)
27" (686)
13 41
9
(650)
2516
(337)
DRAWER FRONT
Height 80" (2032)
Depth
24" (610)
*34 21
10 41
(877)
(260)
Note the location of
pre-drilled holes for
optional handle
hardware.
20 83
15
816
9 43
(248)
(517)
(227)
4
FRONT VIEW
(102)
SIDE VIEW
4
FRONT VIEW
*1/2" (13) +_ ADJUSTMENT IN LEVELING LEGS
(102)
SIDE VIEW
*1/2" (13) +_ ADJUSTMENT IN LEVELING LEGS
I N S TA L L AT I O N S P E C I F I C AT I O N S
Models 427 | 427R
25"
(635)
ROUGH
OPENING
DEPTH
Dimensions are for finished rough openings.
Door swing clearances are based on
stainless steel door and handle dimensions.
IMPORTANT NOTE: The depth of Models
427 and 427R is 24" (610) from the front of
the unit to its back. Your design may necessitate moving the unit back or cabinets
forward to achieve a flush fit. This will
require a minimum rough opening depth of
25" (635).
TOP VIEW
237/8"
(606)
80" (2032)
ROUGH OPENING
HEIGHT
TO FINISHED
FLOORING
27"
(686)
ROUGH OPENING WIDTH
79 1/2" (2019)
MIN HEIGHT
REQUIRED
105˚
90˚
251/2"
MAXIMUM
DOOR SWING
(648)
251/2"
(648)
LOCATE ELECTRICAL
WITHIN SHADED AREA
Dimensions in
parentheses are in
millimeters unless
otherwise specified.
28" (711)
35" (889)
DOOR CLEARANCE
DOOR CLEARANCE
41/2"
151/2"
(114)
(394)
E
21/2"
(64)
56
FRONT VIEW
ANTI-TIP BRACKET
WINE STORAGE
OVERALL DIMENSIONS
All Wine Storage – Model 430
30
5
23 87 (606)
(762)
28 16 (719) DOOR FRAME
ALL WINE
STORAGE
Model 430
Built-In
84
CENTERED VERTICALLY
(2134)
OVERALL
DIMENSIONS
Model 430
10 43
67 87
(273)
(1724)
Width
DOOR
FRAME
30" (762)
Height 84" (2134)
Depth
24" (610)
Note the location of
pre-drilled holes for
optional handle
hardware.
FRONT VIEW
4 81
(105)
TOE
KICK
SIDE VIEW
1
*2 INCH (13) ADJUSTMENT IN LEVELING LEGS
I N S TA L L AT I O N S P E C I F I C AT I O N S
All Wine Storage – Model 430
24"
(610)
ROUGH
OPENING
DEPTH
Dimensions are for finished rough openings.
Door swing clearances are based on
stainless steel door and handle dimensions.
TOP VIEW
ANTI-TIP BLOCK
7"
E
(178)
237/8"
(606)
BEHIND
FRAME
6"
(152)
LOCATE ELECTRICAL
WITHIN SHADED AREA
130˚
90˚
301/8"
MAXIMUM
DOOR SWING
(765)
301/8"
(765)
83 3/4" (2127)
ROUGH OPENING
HEIGHT
TO FINISHED
FLOORING WITH
STANDARD
11" (279) GRILLE
291/2"
(749)
ROUGH OPENING WIDTH
751/2"
(1918)
33" (838)
50" (1270)
83" (2108)
DOOR CLEARANCE
DOOR CLEARANCE
MIN HEIGHT
REQUIRED
(LEVELERS IN)
Refer to installation
instructions shipped
with each Wolf
product for detailed
specifications.
FRONT VIEW
57
WINE STORAGE
ACCESSORIES
Optional accessories
are available
through your
Sub-Zero dealer. To
obtain local dealer
information, visit the
Showroom Locator
section of our
website,
subzero.com.
DOOR PANELS
MODEL 424FS – FREE-STANDING
Unless you are installing a stainless steel model,
you will need to provide a complete door panel
in the instance of a solid door model, or a frame
for the glass door application where wine will be
seen from the outside. If you order a stainless
steel unit, Models 315W, 424, 424FS and 430
will be shipped with their panels and hardware
installed and you will merely install the Sub-Zero.
However, for Models 427 and 427R, you will
have to have the stainless steel panels and
handles installed.
The free-standing Model 424FS does not require
any panels or surrounding cabinetry. It has a
beautiful classic stainless steel exterior, door
frame and handle. Refer to the Overall Dimensions illustration for the Model 424FS.
Wine Storage solid door models are available as
a special order. You must allow 90 days from the
time of order until you can expect delivery.
CABINETRY DIMENSIONS
O V E R L AY PA N E L S P E C I F I C AT I O N S
Model 315W
Model 315W
15"
22 3/8" (568)
(381)
Door Panel Width
15" (381)
Door Panel Height
30 1/16" (764)
Min Width of Rails and Stiles
2 1/4" (57)
Door Frame Panel Weight Limit 10 lbs (5 kg)
34 1/16"
30 1/16"
(865)
OVERALL
HEIGHT
(764)
Min Panel Thickness
TOE
4" (102) KICK
Dimensions in
parentheses are in
millimeters unless
otherwise specified.
58
15 1/8" (384)
19" (483)
OVERALL
WIDTH
FRONT VIEW
SIDE VIEW
5/ 8"
(16)
WINE STORAGE
OVERLAY PANELS –
MODELS 315W | 424
The overlay panel applied to Models 315W and
424 should not be confused with the Built-In
overlay panel application. The overlay panel will
consist of only a frame and would be either the
5/8" (16) or 3/4" (19) thick panel you may be
using. It is affixed directly to the door itself with
screws through a series of pre-drilled holes in
the perimeter of the door itself. You do not need
any backer or spacer panel.
Refer to the Overall Dimensions and Cabinetry
Dimensions illustrations for Models 315W and
424 to give you a better idea of the exact space
our unit needs and how the panel fits in relationship with the unit.
The glass door opening of the standard Model
315W and 424 are designed to be exposed to
room air circulation. Decorative overlays on the
glass should be kept to a minimum. Also, rails
and stiles can be increased in size but should
not exceed cabinet manufacturers‘ standard
width. They cannot exceed overall door panel
dimensions specified, as they would interfere
with the operation of the door. The back sides of
rails and stiles that will be visible through the
glass door will need to be finished. Also, the
inside edges of the frames must be finished to
match the front surface.
The Overall Dimensions illustrations show the
location of predrilled holes for optional handle
hardware. Refer to page 64 for specifics about
installing handles on this overlay application.
IMPORTANT NOTE: Wine Storage models with a
solid door are available as a special order and
require 90 days for delivery. When ordering
panels for a solid door unit, follow the overall
panel dimensions listed; rail and stile dimensions
do not apply. Model 315W is not available with a
solid door.
IMPORTANT NOTE: When planning to install the
Model 315W or 424 next to adjoining cabinetry,
you must make provisions to allow the door to
open to a maximum of 145˚ and not interfere
with the door panel. Refer to the full-scale illustration at the end of this section.
O V E R L AY PA N E L S P E C I F I C AT I O N S
Model 424
Model 424
**23 87 (606)
(CABINET DIMENSION)
23 43 (603) DOOR PANEL
To install overlay
panels, see the
detailed procedures
outlined in the
Sub-Zero Wine
Storage Installation
Instructions.
A solid panel must not be installed on a
glass door unit, as this may cause moisture
to form behind the panel.
CABINETRY DIMENSIONS
23 78
(606)
I N S TA L L AT I O N
Door Panel Width
23 3/4" (603)
Door Panel Height
30 1/16" (764)
Min Width of Rails and Stiles
2 1/4" (57)
Door Frame Panel Weight Limit 10 lbs (5 kg)
1
3016
(764)
DOOR
PANEL
CENTERED
VERTICALLY
*34 21
(877)
4
FRONT VIEW
Solid Door Panel Weight Limit
20 lbs (9 kg)
Min Panel Thickness
5/ 8"
(16)
TOE
SIDE VIEW
(102) KICK
1
*2 INCH (13) ADJUSTMENT IN LEVELING LEGS
7
** MODEL 424/S (STAINLESS STEEL WRAPPED DOOR) FINISHES OFF AT 23 8 INCHES DEEP
59
WINE STORAGE
INTEGRATED PANELS –
MODELS 427 | 427R
ACCESSORIES
Optional accessories
are available
through your
Sub-Zero dealer. To
obtain local dealer
information, visit the
Showroom Locator
section of our
website,
subzero.com.
The integrated full panels or frame panels for
glass doors for these models will follow some of
the identical planning processes used with the
Integrated line. The installation of the door
panels is completely different, however. Rather
than using the mounting hardware we used with
the Integrated line, door panels for both Models
427 and 427R will be applied with screws
applied through our door.
The drawer panels for the Model 427R will be
applied using the Integrated technique of
mounting brackets.
Refer to the Overall Dimensions and Cabinetry
Dimensions illustrations for Models 427 and
427R to give you a better idea of the exact space
our unit needs and how the panel fits in relationship with the unit.
IMPORTANT NOTE: The depth of Models 427
and 427R is 24" (610) from the front of the unit
to its back. You must allow for the thickness of
the panel you are applying when planning for the
finished rough opening depth if you want the
front panel to be flush with surrounding cabinetry. You may have to move the unit back into
the drywall or bring the cabinets forward. Refer
to the Integrated Refrigeration section.
IMPORTANT NOTE: The glass door opening of
the standard Models 427 and 427R is designed
to be exposed to room air circulation. Decorative
overlays on the glass should be kept to a
minimum. While the cabinet front stiles are a
minimum of 2 1/4" (57) for both Models 427 and
427R, the top and bottom rails are different.
Rails and stiles can be increased in size but
should not exceed cabinet manufacturers‘
standard width. They cannot exceed overall door
panel dimensions specified, as they would interfere with the operation of the door. The back
sides of rails and stiles that will be visible
through the glass door will need to be finished.
Also, the inside edges of the frames must be
finished to match the front surface.
IMPORTANT NOTE: The inside edges of the
rough opening will need to be finished as they
will be exposed when the doors are open.
CABINETRY DIMENSIONS
I N T E G R AT E D PA N E L S P E C I F I C AT I O N S
Model 427
Model 427
27
24
(686)
(610)
FINISHED OPENING
DOOR PANEL
(UNIT DIMENSION)
26 43 (679)
Door Panel Width
26 3/4" (679)
Door Panel Height
75 7/8" (1927)
Min Width of Top Rail
3 3/4" (95)
Min Width of Bottom Rail
8" (203)
Min Width of Stiles
2 1/4" (57)
Door Frame Panel Weight Limit 20 lbs (9 kg)
80
(2032)
FINISHED
OPENING
(1927)
79 87
(2029)
DOOR
PANEL
TRIMMED
DOOR
75 87
Dimensions in
parentheses are in
millimeters unless
otherwise specified.
4
4
(102)
(102)
TOE KICK
FRONT VIEW
1
*2
60
TOE KICK
SIDE VIEW
INCH (13) ADJUSTMENT IN LEVELING LEGS
Solid Door Panel Weight Limit
40 lbs (18 kg)
Min Panel Thickness
5/ 8"
(16)
WINE STORAGE
INTEGRATED PANELS –
MODELS 427 | 427R
IMPORTANT NOTE: The dimensions of these
panels and stiles are assuming the models finish
off at 80" (2032) in height overall and have a 4"
(102) toe kick for the Model 427. If you finish off
at 84" (2134), for instance, you must add 4"
(102) additional to the overall height of the panel
and remember to add 4" (102) to the top rail.
Likewise, if you allow for a 6" (152) toe kick for
the Model 427, you must subtract 2" (51) from
the bottom rail.
Door panels for Models 427 and 427R can grow
beyond the 80" (2032) height to accommodate
any size door as long as you stay below door
panel weight limit of 20 lbs (9 kg) for glass door
units and 40 lbs (18 kg) for solid door units.
Refer to the specifications under Door Panel
Height on page 47 of the Integrated section.
IMPORTANT NOTE: The toe kick area on the
Model 427 cannot be larger than 6" (152), and
no larger than 9" (229) for the 427R. The toe
kick area for either model cannot be less than
4" (102).
In the Overall Dimensions illustrations, note the
location of pre-drilled holes for optional handle
hardware. Refer to page 64 for specifics about
installing handle hardware on this overlay
application.
IMPORTANT NOTE: If you are installing
Sub-Zero‘s optional lock kit on a Model 427 or
427R, you may have to order door panels that
exceed the 80" (2032) finished height. Consult
the lock kit installation instructions and see if
your panels will allow for an adequate installation. To obtain these instructions, check our
website, subzero.com.
IMPORTANT NOTE: In the panel specifications
for Model 427R, the bottom drawer panel height
is based on a 4" (102) toe kick. If you want to
show a 6" (152) toe kick, you must subtract 2"
(51) from the bottom drawer panel height.
IMPORTANT NOTE: Wine Storage models with a
solid door are available as a special order and
require 90 days for delivery. When ordering
panels for a solid door unit, follow the overall
panel dimensions indicated in the chart; rail and
stile dimensions do not apply.
I N T E G R AT E D PA N E L S P E C I F I C AT I O N S
Model 427R
Model 427R
24
(686)
(610)
FINISHED OPENING
DOOR PANEL
(UNIT DIMENSION)
26 43 (679)
To install integrated
panels, see the
detailed procedures
outlined in the
Sub-Zero Wine
Storage Installation
Instructions.
A solid panel must not be installed on a
glass door unit, as this may cause moisture
to form behind the panel.
CABINETRY DIMENSIONS
27
I N S TA L L AT I O N
Door Panel Width
26 3/4" (679)
Door Panel Height
45 3/8" (1153)
Min Width of Top Rail
3 3/4" (95)
Min Width of Bottom Rail
3" (76)
Min Width of Stiles
2 1/4" (57)
Door Frame Panel Weight Limit 20 lbs (9 kg)
80
45 83
(2032)
(1153)
FINISHED
OPENING
79 87
(2029)
1
8
(3)
TRIMMED
DOOR
13169
1
8 (345)
(3)
26 34 (679)
Solid Door Panel Weight Limit
40 lbs (18 kg)
Top Drawer Panel Width
26 3/4" (679)
Top Drawer Panel Height
13 9/16" (345)
Bottom Drawer Panel Width
26 3/4" (679)
Bottom Drawer Panel Height
16 11/16" (424)
Drawer Panel Weight Limit
12 lbs (5 kg) each
Min Panel Thickness
5/ 8"
(16)
DRAWER PANEL
*34 21
(877)
11
1616
(424)
4
4
(102)
(102)
TOE KICK
FRONT VIEW
1
*2
TOE KICK
SIDE VIEW
INCH (13) ADJUSTMENT IN LEVELING LEGS
61
WINE STORAGE
MODEL 430 – FRAMED PANELS
MODEL 430 – OVERLAY PANELS
You cannot use a 1/4" (6) panel to cover the
glass door of a framed Model 430. It is fine
when applying a panel to the solid door, but in
either instance, you should consider using raised
panels with a minimum 5/8" (16) thickness.
Your overlay model will be shipped without
handle hardware and with an 11" (279) overlay
panel grille as standard equipment. You will need
to order a panel for the grille and hardware to
complement your surrounding cabinetry.
When using a raised framed panel, you must
allow for the edge to be routed 1/4" (6) around
the panel to ensure a proper fit. Refer to
illustration 1.
While the overlay panel design offers you a more
seamless appearance, you need to be aware of
adjacent cabinets and/or countertops when the
door is opened. Refer to the full-scale illustrations at the end of the Built-In section.
With the framed Model 430, you will receive an
extruded handle identical in appearance to the
Built-In models. However, it will be an extended
handle and will enable you to use raised panels
without providing finger clearance to open the
door.
IMPORTANT NOTE: Wine Storage models with a
solid door are available as a special order and
require 90 days for delivery. When ordering
panels for a solid door unit, follow the overall
panel dimensions indicated; rail and stile dimensions do not apply.
A solid panel must not be installed on a
glass door unit, as this may cause moisture
to form behind the panel.
To achieve the overlay look, you need three
different panels—the decorative overlay panel, a
0.10" (3) spacer panel and a 1/4" (6) backer
panel. Depending on your cabinet manufacturer,
this could be one panel routed for different
dimensions or more likely, three different panels.
Refer to the Overlay Panel Specifications for
complete details on the overlay sizing. In
addition, illustrations 2 and 3 will give you a
better idea of the panel construction and how it
interacts with our frame.
The glass door opening of the standard Model
430 is designed to be exposed to room air circulation. Decorative overlays on the glass should
be kept to a minimum. Also, rails and stiles can
be increased in size but should not exceed
cabinet manufacturers‘ standard width. They
cannot exceed overall door panel dimensions
specified, as they would interfere with the operation of the door.
The back sides of rails and stiles that will be
visible through the glass door will need to be
finished. Also, the inside edges of the frames
must be finished to match the front surface.
Trim Reveal 1/4" (6) min
Rout to 1/4" (6) thickness
2 1/4" (57) Rail/ Stile
Overlay Panel
.10" (3) Spacer Panel
.10"
(3)
2 1/4" (57)
Door
Frame
Spacer Panel
Overlay Panel
1/4" (6) Backer Panel
5/16" (8) min
Rail/Stile
Door Frame
5/32" (4)
5/8"
(16)
Illus. 1
62
1/16" (2)
Glass
Glass
5/8"
min
(16)
Backer
Panel
Door / Grille
Trim
.10" (3) 1/4" (6)
Illus. 2
Illus. 3
WINE STORAGE
MODEL 430 – OVERLAY PANELS
As with the Sub-Zero Built-In models, you have
the flexibility of ordering grilles in a variety of
heights for either the framed or overlay application. Optional panel grille dimensions for the
framed Model 430 are the same as listed for
Built-In Models 611 and 611G on page 21.
Overlay grille panel dimensions for the overlay
Model 430, standard 11" (279) grille, are listed
below. Refer to page 25 for optional grille height
dimensions. The width of the overlay grille,
spacer and backer panel will be the same regardless of the height.
IMPORTANT NOTE: Wine Storage models with a
solid door are available as a special order and
require 90 days for delivery. When ordering
panels for a solid door unit, follow the overall
panel dimensions indicated; rail and stile dimensions do not apply.
A solid panel must not be installed on a
glass door unit, as this may cause moisture
to form behind the panel.
In addition, side panel information for a Model
430 is available on page 26 of the Built-In
section. Refer to illustration 12 on page 26 for
placement of toe kick and grille area cut-outs.
CABINETRY DIMENSIONS
F R A M E D PA N E L S P E C I F I C AT I O N S
Model 430
Model 430 – Framed (F)
30
7
(762)
28 16 (722) DOOR FRAME
Framed Door Panel Width
28 1/8" (714)
Framed Door Panel Height
67 11/16" (1719)
Min Width of Rails and Stiles
2 1/4" (57)
I N S TA L L AT I O N
To install framed or
overlay panels, see
the detailed procedures outlined in the
Sub-Zero Wine
Storage Installation
Instructions.
Door Frame Panel Weight Limit 25 lbs (11 kg)
84
Solid Door Panel Weight Limit
50 lbs (23 kg)
Min Panel Thickness
5/ 8"
(16)
O V E R L AY PA N E L S P E C I F I C AT I O N S
(2134)
Model 430 – Overlay (O)
68
(1727)
DOOR
PANEL
CENTERED
VERTICALLY
Overlay Door Panel Width
28 7/16" (722)
Overlay Door Panel Height
68" (1727)
Spacer Panel Width
27 1/2" (699)
Spacer Panel Height
67 1/16" (1073)
Backer Panel Width
28 1/8" (714)
Backer Panel Height
67 11/16" (1719)
Min Width of Rails and Stiles
2 1/4" (57)
Door Frame Panel Weight Limit 25 lbs (11 kg)
FRONT VIEW
1
*2
1
4 16
(103)
TOE
KICK
Solid Door Panel Weight Limit
50 lbs (23 kg)
Min Panel Thickness
5/ 8"
(16)
SIDE VIEW
INCH (13) ADJUSTMENT IN LEVELING LEGS
G R I L L E PA N E L S P E C I F I C AT I O N S
Model 430 – Overlay (O)
Overlay Grille Panel Width
28 7/16" (722)
Overlay Grille Panel Height*
10 1/4" (260)
Spacer Panel Width
27 1/2" (699)
Spacer Panel Height*
9 5/16" (236)
Backer Panel Width
28 1/8" (714)
Backer Panel Height*
9 15/16" (252)
Grille Panel Weight Limit
15 lbs (7 kg)
Min Panel Thickness
5/ 8"
(16)
Dimensions in
parentheses are in
millimeters unless
otherwise specified.
*Grille panel dimensions are for standard 11" (279)
grille. Refer to page 25 for optional grille heights.
63
WINE STORAGE
ACCESSORIES
Optional accessories
are available
through your
Sub-Zero dealer. To
obtain local dealer
information, visit the
Showroom Locator
section of our
website,
subzero.com.
HARDWARE CONSIDERATIONS
WINE SHELF WOOD FACING
With Models 315W and 424 (overlay), Models
427 and 427R (integrated) and the Model 430
(overlay), you must supply your own handle
hardware. It is recommended you use our
optional handles and use the pre-drilled holes
supplied to locate the handles within the frame
of our unit. The metal frame on the door has
numerous mounting holes on each side to
accommodate Sub-Zero accessory handles.
This will allow you to provide the best possible
handle alignment and not take away from the
strength of the stile in this area after the unit is
used a number of times. We recommend using a
pull handle and not a pull knob.
Sub-Zero has provided a natural cherry wood
facing to its wine storage shelves in each model.
You can also replace these strips with wood
more complementary to your design and
surrounding cabinetry.
If you elect to place different hardware on these
units, we encourage you to fasten the hardware
by passing through our door and attaching the
hardware through the Sub-Zero door‘s frame.
Optional stainless steel handles are available in a
variety of diameters and lengths, as are handles
to match the color and style of Wolf ovens.
Contact your Sub-Zero dealer for specifics.
When planning for hardware, refer to the
Door Frame Profile full-scale illustration on
the following page to give you a better
understanding of the unit‘s frame and positioning of the glass for the door. You must
not drill through this glass.
Dimensions in
parentheses are in
millimeters unless
otherwise specified.
64
The Wine Shelf Wood Facing illustration on the
following page can be used as a full-scale
template. You must follow the layout of this
format to accommodate the shelves properly. To
remove the cherry strips, take the shelves out
and remove the screws. Reverse the procedure
to affix the new wood.
If you choose to stain or seal the wood facing,
be aware that some of these substances are
hazardous and will damage stored wine.
WINE STORAGE
DOOR FRAME PROFILE
DOOR FRAME HANDLE OFFSET
Wine Storage Models
Glass
Cabinet Door
Profile
CL
A
Dimension A
Model 315W
1" (25)
Model 424
1" (25)
Model 427
7/ 8"
(22)
Model 427R
7/ 8"
(22)
Model 430
15/16"
(24)
IMPORTANT NOTE: Rails and stiles must be
a minimum of 2 1/4" (57) wide (except for the
rails of Models 427 and 427R, which must
be wide enough to cover the door hinges).
The back sides of rails and stiles that will be
visible through the glass door will need to be
finished.
A
2 1/4" (57) Rail/ Stile
This full-scale illustration is typical of the
Model 424 door frame profile; details of the other
Wine Storage door frames will vary slightly.
FULL-SCALE
T E M P L AT E S
The full-scale illustrations on the
following pages
enable you to understand some of the
unique situations
you may face as you
plan for the installation of the Wine
Storage units. Use
these illustrations as
templates.
WINE SHELF WOOD FACING
5/8"
(16)
Maximum Thickness
7/64"
(3)
11/2" (38)
27/32"
(21)
5/64"
(2)
A (WIDTH)
23/64"
(9)
9/16" (14)
SIDE VIEW
FRONT VIEW
This full-scale illustration provides the dimensions
you will need should you choose to replace the
natural cherry wood facing of each wine shelf
with wood more complementary to your design
and surrounding cabinetry.
IMPORTANT NOTE: Dimensions will vary for
Model 315W. Additional information can be found
in the Specifications pdf file for Model 315W on
our website, subzero.com.
W I N E S H E L F W O O D FA C I N G
Wine Storage Models
Dimension A
Model 315W*
10 15/16" (278)
Model 424
19 1/2" (495)
Model 424FS
19 1/2" (495)
Model 427
20 15/16" (532)
Model 427R
20 15/16" (532)
Model 430
24 9/16" (624)
*Dimensions will vary for Model 315W.
65
WINE STORAGE
MODEL 424 – DOOR CLOSED AND 145˚ MAX OPENING
24 (610)
CABINETRY
OPENING
1
238 (587)
TO BACK OF
APPLIANCE
*MODEL 424 MUST
EXTEND A MINIMUM
1/4" (6) BEYOND THE
FRONT SURFACE OF
ADJOINING
CABINETRY TO
ALLOW THE MAXIMUM
DOOR SWING
SUB-ZERO DOOR
3
4 (19)
1
2
(13)
DOOR PANEL
1
4 (6)*
3
23 4 (600)
1 (3)
8
DOOR PANEL
WIDTH
DOOR
PANEL
145˚*
The full-scale illustration shows what
considerations you need to make for the
installation of Model 424 and how the
maximum door opening may interact with
adjacent cabinets and countertops.
66
SUB-ZERO
DOOR
UNDERCOUNTER REFRIGERATION
NEW UNDERCOUNTER REFRIGERATION
Available in 2007
Aside from the full-size models that Sub-Zero
offers in its Built-In and Integrated lines of
refrigeration and its Wine Storage equipment, we
round out our product line-up with a new line of
Undercounter refrigeration available in 2007.
Our new Undercounter line consists of an all
refrigerator model, an all refrigerator beverage
center, a refrigerator / freezer combination model
and an all refrigerator model designed for
outdoor applications. Included in the line is the
Undercounter Model 315I(P) ice maker.
NEW
A L L R E F R I G E R AT O R
23 7/8" (606)
34"
(864)
MODEL UC-24R
All Refrigerator
NEW
BEVERAGE CENTER
23 7/8" (606)
The Undercounter models accept a decorative
door panel for an overlay or stainless steel
application and can be built in to fit flush with
virtually any base cabinet style. The outdoor
Model UC-24RO is available in classic stainless
steel only and comes with door panel and
handle in place. Model UC-24RO must also be
built-in into cabinetry and is not designed to be a
free-standing unit.
A classic stainless steel door panel with handle
is available as a sales accessory for Models
UC-24R, UC-24C and 315I(P). Contact your
Sub-Zero dealer for information on accessory
panels and handles. Model UC-24B must be
ordered as overlay (UC24-B/O) or stainless steel
(UC-24B/S).
Sub-Zero Undercounter models are all backed by
one of the best warranties in the industry.
34"
(864)
MODEL UC-24B
All Refrigerator
SUB-ZERO
WARRANTY
Sub-Zero products
are covered by a
two, five and twelve
year residential
warranty (one and
five year warranty
for Model UC-24RO).
See warranty details
at the end of this
guide.
NEW
C O M B I N AT I O N
23 7/8" (606)
34"
(864)
MODEL UC-24C
Combination
Refrigerator / Freezer
NEW
OUTDOOR MODEL
23 7/8" (606)
Undercounter models, except Model 315I(P),
are Star-K compliant to meet strict religious
regulations in conjunction with specific
instructions found on www.star-k.org.
34"
(864)
MODEL UC-24RO
All Refrigerator
ICE MAKER
15 3/16"
(386)
335/8"
(854)
Comprehensive installation instructions are
shipped with each model. Refer to those
instructions in preparing and installing all
Sub-Zero products. The instructions can also
be found on our website, subzero.com.
MODEL 315I(P)
Ice Maker
Dimensions in
parentheses are in
millimeters unless
otherwise specified.
67
UNDERCOUNTER REFRIGERATION
MODEL UC-24R
NEW
A L L R E F R I G E R AT O R
MODEL UC-24B
NEW
BEVERAGE CENTER
MODEL UC-24C
NEW
C O M B I N AT I O N
R E F R I G E R AT O R | F R E E Z E R
Energy Star Qualified
MODEL OPTIONS
Available Fall 2007
Overlay Design
UC-24B/O
Classic Stainless Steel
UC-24B/S
Full-View Glass Door (standard)
High Altitude Glass Door**
S P E C I F I C AT I O N S
S P E C I F I C AT I O N S
S P E C I F I C AT I O N S
Overall Width
23 7/8" (606)
Overall Width
23 7/8" (606)
Overall Width
23 7/8" (606)
Overall Height
34" (864)
Overall Height
34" (864)
Overall Height
34" (864)
Overall Depth
24" (610)
Overall Depth
24" (610)
Overall Depth
24" (610)
Refrigerator Capacity
5.7 cu ft (161 L)
Refrigerator Capacity
5.7 cu ft (161 L)
Refrigerator Capacity
3.6 cu ft (102 L)
Min Height Required
34 1/4" (870)
Wine Storage Capacity
16 bottles***
Wine Storage Capacity
8 bottles***
Door Swing Clearance
25 3/8" (645)
Min Height Required
34 1/4" (870)
Freezer Capacity
1.1 cu ft (31 L)
Specify Door Swing
LH or RH
Door Swing Clearance
25 3/8" (645)
Min Height Required
34 1/4" (870)
Annual Energy Usage
339 kWh | $31*
Specify Door Swing
LH or RH
Door Swing Clearance
25 3/8" (645)
Shipping Weight
130 lbs (59 kg)
Annual Energy Usage
424 kWh | $39*
Specify Door Swing
LH or RH
Shipping Weight (O)
130 lbs (59 kg)
Annual Energy Usage
434 kWh | $40*
Shipping Weight (S)
135 lbs (61 kg)
Shipping Weight
130 lbs (59 kg)
F E AT U R E S
F E AT U R E S
F E AT U R E S
2 Adjustable Glass Shelves
2 Wine Storage Shelves
1 Wine Storage Shelf
1 Utility Bin
1 Adjustable Glass Shelf
1 Adjustable Glass Shelf
2 Door Shelves
1 Utility Bin
1 Door Shelf
Automatic Defrost
Automatic Ice Maker
MODEL UC-24R
MODEL UC-24B
MODEL UC-24C
*Annual energy costs are based on
9.06 cents per kilowatt hour.
**High altitude glass doors are for
installations at or above 5,000'
(1524 m) in elevation and will be
treated as a special order. Please allow
90 days for delivery. When ordering,
put an (A) after the (B) to obtain the
correct model number.
Dimensions in
parentheses are in
millimeters unless
otherwise specified.
68
**750 ml bottles
Optional stainless steel panels and
handles are ordered and shipped as
sales accessories for Models UC-24R,
UC-24C and 315I(P).
UNDERCOUNTER REFRIGERATION
MODEL UC-24RO
MODEL 315I
NEW
ICE MAKER
A L L R E F R I G E R AT O R
OUTDOOR MODEL
Energy Star Qualified
MODEL OPTIONS
Available Summer 2007
Drain Pump Model
315IP
S P E C I F I C AT I O N S
S P E C I F I C AT I O N S
ACCESSORIES
Overall Width
23 7/8" (606)
Overall Width
15 3/16" (386)
Overall Height
34" (864)
Overall Height
33 5/8" (854)
Overall Depth
24" (610)
Overall Depth
24" (610)
Refrigerator Capacity
5.7 cu ft (161 L)
Ice Storage Capacity
26 lbs (12 kg)
Min Height Required
34 1/4" (870)
Min Height Required
33 3/4" (857)
Door Swing Clearance
25 3/8"
Door Swing Clearance
15 1/4" (387)
Specify Door Swing
LH or RH
Shipping Weight
100 lbs (45 kg)
Annual Energy Usage
339 kWh | $31*
Shipping Weight
130 lbs (59 kg)
(645)
F E AT U R E S
F E AT U R E S
2 Adjustable Glass Shelves
Automatic Ice Maker
1 Utility Bin
Automatic Defrost
2 Door Shelves
Reversible Door Swing
Door Lock
Drain Pump (Model 315IP)
Optional accessories
are available
through your
Sub-Zero dealer. To
obtain local dealer
information, visit the
Showroom Locator
section of our
website,
subzero.com.
Classic Stainless Steel Finish
MODEL UC-24RO
MODEL 315I(P)
ACCESSORIES
Contact your Sub-Zero Dealer
Classic stainless steel door front
panel with tubular handle
Classic stainless steel tubular
handle for overlay application
UL approved door lock
69
UNDERCOUNTER REFRIGERATION
UNDERCOUNTER FEATURES
Overlay Application. The overlay application
blends seamlessly into your overall room design
and complements surrounding cabinetry. You add
the decorative door front panel and hardware.
Sub-Zero accessories handles are available.
The overlay application is available for all Undercounter models except Model UC-24RO. Model
UC-24B must be ordered specifically as overlay
(UC24-B/O).
SUB-ZERO
WARRANTY
Sub-Zero products
are covered by a
two, five and twelve
year residential
warranty (one and
five year warranty
for Model UC-24RO).
See warranty details
at the end of this
guide.
Stainless Steel Application. A classic stainless
steel door front panel and handle is available as
an accessory for Models UC-24R, UC-24C and
315I(P). Model UC-24B must be ordered specifically as stainless steel (UC-24B/S). Model
UC-24RO is available as a classic stainless steel
model only and comes with door panel and
handle in place.
Glass Door—Model UC-24B. The full-view glass
door and accent lighting of Model UC-24B
matches the appearance of Wine Storage Model
424.
Electronic Controls. The electronic controls with
digital readout LCD display are up front and easy
to access—not applicable on Model 315I(P).
Glass Shelves. Cantilevered glass shelves are
adjustable, easy to clean and spill proof. The
glass floor is also spill proof.
Utility Bin. Refrigerator and combination units
feature a clear utility bin for storage of smaller
items.
Dimensions in
parentheses are in
millimeters unless
otherwise specified.
70
Wine Storage. Models UC-24B and UC-24C
feature wine storage of 16 and 8 (750 ml)
bottles, respectively. The roller-glide wine
storage shelves faced with natural cherry wood
have a three-quarter extension for easy access.
Automatic Ice Maker. Combination Model
UC-24C features an automatic ice maker with
clear ice bucket. The ice maker provides highquality, crescent-shaped ice that won’t stick to
the side of the glass.
Two-Litre Bottle Storage. Models UC-24B,
UC-24R and UC-24RO feature two-litre bottle
storage in the bottom door shelf.
Door Lock. A UL approved lock is standard on
Model UC-24RO and available as a sales accessory for all other models except Model 315I(P).
Sabbath Feature. The Sabbath feature will allow
the lights to remain off during certain religious
observances—not applicable on Model 315I(P).
Ice Maker. Model 315I(P) provides high-quality,
clear ice with a storage capacity of up to 26 lbs
(12 kg). The ice is not crescent shaped, but
instead resembles a small barrel.
Drain. Ice maker Model 315I has a gravity drain,
while Model 315IP has a built-in pump to allow
water to drain into adjacent sink.
UNDERCOUNTER REFRIGERATION
PLANNING INFORMATION
ELECTRICAL REQUIREMENTS
Refer to the Installation Specifications for information regarding area requirements, minimum
door clearance, placement of electrical and
plumbing for Sub-Zero Undercounter models.
A 115 V AC, 60 Hz, 15 amp circuit breaker and
electrical supply are required. A separate circuit,
servicing only this appliance is required.
The Model 315I can be ordered with or without
a pump. If you order the unit without a pump,
you must install a drain. Refer to the illustrations
on page 73. The drain must be located in a 2"
(51) area centered in the opening for the unit,
23" (651) back from the front door.
PLUMBING REQUIREMENTS
For Models UC-24C and 315I(P), rough in the
water supply line. Connect a 1/4" OD copper line
to the house supply with an easily accessible
shut-off valve between the supply and the unit.
A minimum of 26" (660) of copper tubing is
required for the water line for Model UC-24C.
Do not use self-piercing valves. A saddle valve
kit (4200880) is available from your Sub-Zero
dealer. An in-line filter is required when water
conditions have a high sediment content.
All Undercounter models are equipped with a
power supply cord with a 3-prong grounding
plug, which must be plugged into a mating
3-prong grounding-type wall receptacle. Follow
the National Electrical Code and local codes and
ordinances when installing the receptacle. Refer
to the Installation Specifications illustrations.
IMPORTANT NOTE: The Model UC-24RO is
designed and safe for use in outdoor applications. When installed outdoors, a ground fault
circuit interrupter (GFCI) is required to reduce
the risk of electrical shock. A GFCI is not
recommended for use with other Undercounter
models and may cause interruption of operation.
MODEL OPTIONS
Model UC-24R
All Refrigerator
Model UC-24B
All Refrigerator
Beverage Center
Model UC-24C
Refrigerator | Freezer
with Ice Maker
Model UC-24RO
All Refrigerator
Outdoor Model
Model 315IP
Ice Maker with
Drain Pump
The ice maker operates on constant water
pressure between 20 psi (1.4 bar) and 100 psi
(6.9 bar).
IMPORTANT NOTE: In some cases, a reverse
osmosis water filter system may not be able to
maintain the minimum pressure consistently.
71
UNDERCOUNTER REFRIGERATION
I N S TA L L AT I O N S P E C I F I C AT I O N S
Models UC-24R, UC-24B, UC-24C and UC-24RO
2" (51)
15 1/2"
(394)
1/2" (13)
LOCATE WATER LINE
(MODEL UC24C ONLY)
WITHIN SHADED AREA
Overall Dimensions
Overall Width
23 7/8" (606)
Overall Height
34" (864)
Overall Depth
24" (610)
24"
(610)
ROUGH
OPENING
DEPTH
TOP VIEW
Finished Opening Dimensions
Opening Width
24" (610)
Opening Height
34 1/2" (876)
Opening Depth
24" (610)
Door Swing Clearance
25 3/8"
24" (610)
ROUGH OPENING
WIDTH
(645)
Models without an ice maker will not require
the water line connection.
ANTI-TIP BRACKET
Door swing clearance based on stainless steel
door panel and handle dimensions.
LOCATE ELECTRICAL
AND WATER LINE
(MODEL UC24C ONLY)
WITHIN SHADED AREA
15 1/2"
341/2"
(876)
ROUGH
OPENING
HEIGHT
341/4"
(870)
MINIMUM
HEIGHT
REQUIRED
(394)
3" (76)
2" (51)
FRONT VIEW
90˚
25 3/8"
(644)
26" (660)
DOOR CLEARANCE
15 3/16"
I N S TA L L AT I O N S P E C I F I C AT I O N S
(386)
Model 315I(P)
Overall Dimensions
19"
(483)
8"
1/2"
(13)
Overall Width
15 3/16" (386)
Overall Height
33 5/8" (854)
Overall Depth
24" (610)
(203)
LOCATION OF
WATER LINE
24"
(610)
ROUGH
OPENING
DEPTH
TOP VIEW
115˚
DOOR SWING
Finished Opening Dimensions
Opening Width
15 1/4" (387)
Opening Height
34 1/2" (876)
Opening Depth
24" (610)
Door Swing Clearance
15 1/4" (387)
15 1/4" min (387)
ROUGH
OPENING WIDTH
Refer to the illustrations on the following
page for additional specifications.
Door swing clearance based on stainless
steel door panel and handle dimensions.
Dimensions in
parentheses are in
millimeters unless
otherwise specified.
72
LOCATE
ELECTRICAL
ANYWHERE ON
BACK WALL
FRONT VIEW
341/2"
(876)
ROUGH
OPENING
HEIGHT
33 3/4"
(857)
MINIMUM
HEIGHT
REQUIRED
UNDERCOUNTER REFRIGERATION
MODEL 315I(P) – GRAVITY DRAIN
OR DRAIN PUMP
The Undercounter ice maker can be ordered with
a pump (Model 315IP) or without a pump (Model
315I). The model without a drain pump drains its
water by gravity. However, the gravity drain
model may be converted to a pump model
through the installation of a drain pump kit and
drain pump.
Specific step-by-step instructions are included
with the drain pump kit. Contact your Sub-Zero
dealer for specifics.
The drain and inlet water tubes must be
plumbed before connecting to the ice maker. For
the gravity drain, all horizontal runs of drain lines
must have a 1/4" (6) per 12" (305) fall. An air gap
will likely be required between the ice maker
drain tube and the drain/waste receptacle. A
stand pipe with a trap below it would be acceptable for the drain/waste receptacle. Refer to the
illustrations below.
ACCESSORIES
IMPORTANT NOTE: Poor drainage will cause a
high rate of ice melting in the bin.
I N S TA L L AT I O N S P E C I F I C AT I O N S
Model 315I – Gravity Drain
Model 315IP – Drain Pump
1/8"(3)
24"
(610)
1/8"(3)
SHUT-OFF
VALVE
WATER
INLET
TUBE
WATER
INLET TUBE
SHUT-OFF
VALVE
DRAIN
TUBE
WATER
FILTER
WATER
FILTER
DRAIN
TUBE
24"
(609)
LOCATE DRAIN
WITHIN 2" DIA.
AREA 23" BACK
FROM FRONT
OF UNIT
AIR GAP
DEVICE
151/4"
(387) MIN.
151/4"
(387) MIN.
TOP VIEW
TOP VIEW
AIR GAP
DEVICE
341/2"
(876) NOMINAL
341/2"
(876) NOMINAL
333/4"
(857) MIN.
DRAIN
TUBE
WATER
FILTER
WATER
INLET TUBE
Optional accessories
are available
through your
Sub-Zero dealer. To
obtain local dealer
information, visit the
Showroom Locator
section of our
website,
subzero.com.
SHUT-OFF
VALVE
333/4"
(857) MIN.
WATER
INLET TUBE
SHUT-OFF
VALVE
DRAIN
TUBE
151/4"
(387) MIN.
FRONT VIEW
WATER
FILTER
151/4"
(387) MIN.
FRONT VIEW
Refer to installation
instructions shipped
with each Wolf
product for detailed
specifications.
73
UNDERCOUNTER REFRIGERATION
OVERLAY PANEL – MODELS UC-24R
AND UC-24C
The overlay door panel design allows for a
decorative panel to cover the door trim for a
seamless appearance that will compliment
surrounding cabinetry. You may also choose to
match the handle hardware of surrounding
cabinetry.
I N S TA L L AT I O N
To install framed or
overlay panels, see
the detailed procedures outlined in the
Sub-Zero Undercounter Installation
Instructions.
Refer to the fullscale illustrations at
the end of this
section for specifics
on door openings
and other specifications.
Refer to the Overlay Panel Specifications below
for the panel dimensions of your specific model.
Outdoor Model UC-24RO is available as a classic
stainless steel model only and comes with door
panel and handle in place.
OVERLAY PANEL – MODEL UC-24B
The overlay door panel applied to the Model
UC-24B will consist of only a frame and will affix
directly to the door with screws through a series
of predrilled holes in the perimeter of the door.
The glass door opening of the Model UC-24B is
designed to be exposed to room air circulation.
Decorative overlays on the glass should be kept
to a minimum. Refer to the Overlay Panel
Specifications below for panel dimensions.
Rails and stiles must be a minimum of 21/4" (57)
wide. They can be increased in size but should
not exceed cabinet manufacturers standard
width. Rails and stiles cannot exceed the overall
door panel dimensions specified, as they would
interfere with the operation of the door. The
back sides of rails and stiles that will be visible
through the glass door will need to be finished.
Also, the inside edges of the frames must be
finished to match the front surface.
A solid panel must not be installed on a
glass door unit, as this may cause moisture
to form behind the panel.
OVERLAY PANEL – MODEL 315I(P)
It is important to understand the differences in
mounting any wood panel to the Model 315I(P).
Refer to the Overlay Panel Specifications below
for panel dimensions. Also refer to the installation instructions packaged with the unit to
understand how the panel is installed.
O V E R L AY PA N E L S P E C I F I C AT I O N S
Undercounter Models
Models UC-24R and UC-24C
Door Panel Width
23 3/4" (603)
Door Panel Height
30 1/16" (764)
Panel Thickness
5/ 8"
Panel Weight Limit
20 lbs (9 kg) max
W
Model UC-24B
Door Panel Width
23 3/4" (603)
Door Panel Height
30 1/16" (764)
Width of Rails and Stiles
2 1/4" (57) min
Panel Thickness
5/ 8"
Panel Weight Limit
10 lbs (5 kg) max
(16) min
Model 315I(P)
Dimensions in
parentheses are in
millimeters unless
otherwise specified.
74
H
(16) min
Door Panel Width
15" (381)
Door Panel Height
30 3/8" (772)
Panel Thickness
5/ 8"
Panel Weight Limit
15 lbs (7 kg) max
(16) min
Models UC-24R
and UC-24C
H
W
Model UC-24B
H
W
Model 315I(P)
UNDERCOUNTER REFRIGERATION
DOOR FRAME PROFILE – MODEL UC-24B
Glass
FULL-SCALE
T E M P L AT E S
Door Panel Profile
CL
1" (25)
The full-scale illustration shows the door frame
profile for Model UC-24B.
1" (25)
IMPORTANT NOTE: Rails and stiles must be a
minimum of 2 1/4" (57) wide. The back sides of rails
and stiles that will be visible through the glass
door will need to be finished.
2 1/4" (57) Rail/ Stile
The full-scale illustrations on the
following pages
enable you to understand some of the
unique situations
you may face as you
plan for the installation of the Undercounter units. Use
these illustrations as
templates.
DOOR FRAME PROFILE
WINE SHELF WOOD FACING – MODELS UC-24B AND UC-24C
5/8"
(16)
Maximum Thickness
7/64"
(3)
11/2" (38)
27/32"
(21)
5/64"
(2)
19 1/2" (495)
23/64"
(9)
9/16" (14)
FRONT VIEW
SIDE VIEW
For Models UC-24B and UC-24C, use the full-scale
illustration above as a template if you choose to
replace the natural cherry wood facing with
wood more complementary to your design and
surrounding cabinetry.
75
UNDERCOUNTER REFRIGERATION
UNDERCOUNTER DOOR CLOSED AND 145˚ MAX OPENING
The full-scale illustration shows
what considerations you need
to make for the installation of
the Undercounter unit and how
the maximum door opening
may interact with adjacent
cabinets and countertops.
24 (610)
CABINETRY
OPENING
1
238 (587)
TO BACK OF
APPLIANCE
SUB-ZERO DOOR
3
4 (19)
1
2
(13)
*UNDERCOUNTER
UNIT MUST EXTEND
A MINIMUM 1/4" (6)
BEYOND THE FRONT
SURFACE OF
ADJOINING
CABINETRY TO
ALLOW THE MAXIMUM
DOOR SWING
DOOR PANEL
1
4 (6)*
3
23 4 (600)
1 (3)
8
DOOR PANEL
WIDTH
DOOR
PANEL
145˚*
Dimensions are in
inches with millimeters in parentheses
unless otherwise
specified.
76
SUB-ZERO
DOOR
SUB-ZERO PRODUCTS
LIMITED WARRANTY
RESIDENTIAL USE ONLY
FULL FIVE YEAR SEALED SYSTEM WARRANTY
LIMITED SIXTH THROUGH TWELFTH YEAR WARRANTY ON THE SEALED SYSTEM
FULL TWO YEAR WARRANTY ON TOTAL PRODUCT*
FULL FIVE YEAR SEALED SYSTEM WARRANTY
For five years from the date of original installation, your Sub-Zero warranty covers all parts and labor
to repair or replace any components that prove to be defective in materials or workmanship in the
sealed system. The sealed system consists of the compressor, condenser, evaporator, drier and all
connecting tubing.
FULL TWO YEAR WARRANTY*
For two years from the date of original installation, your Sub-Zero warranty covers all parts and labor
to repair or replace any part of the product, that proves to be defective in materials or workmanship.
LIMITED SIXTH THROUGH TWELFTH YEAR SEALED SYSTEM WARRANTY
From the 6th through the 12th year from the date of original installation, your Sub-Zero warranty
covers all parts that prove to be defective in materials or workmanship in the sealed system (parts
only). The sealed system consists of the compressor, condenser, evaporator, drier and all connecting
tubing.
TERMS APPLICABLE TO EACH WARRANTY
All service provided by Sub-Zero under the above warranty must be performed by an authorized
Sub-Zero service center, unless otherwise specified by Sub-Zero. Service will be provided in the
home during the normal business hours. This warranty applies only to products installed for normal
residential use. Details regarding a non-residential warranty are available upon request.
The warranty applies only to products installed in any one of the fifty states of the United States, the
District of Columbia or the ten provinces of Canada. This warranty does not cover any parts or labor
to correct any defect caused by negligence, accident or improper use, maintenance, installation,
service or repair, including but not limited to improper removal and reinstallation (whether in the unit
or at a remote location) of the condensing unit.
THE REMEDIES DESCRIBED ABOVE FOR EACH WARRANTY ARE THE ONLY ONES THAT
SUB-ZERO WILL PROVIDE, EITHER UNDER THESE WARRANTIES OR UNDER ANY WARRANTY
ARISING BY OPERATION OF LAW. SUB-ZERO WILL NOT BE RESPONSIBLE FOR ANY CONSEQUENTIAL OR INCIDENTAL DAMAGES ARISING FROM THE BREACH OF THESE WARRANTIES
OR ANY OTHER WARRANTIES, WHETHER EXPRESS, IMPLIED OR STATUTORY.
Some states do not allow the exclusion or limitation of incidental or consequential damages, so the
above limitation or exclusion may not apply to you. This warranty gives you specific legal rights and
you may also have other legal rights, which vary from state to state.
To receive parts and/or service and the name of the Sub-Zero authorized service center nearest
you, contact your Sub-Zero dealer, distributor or the Sub-Zero Customer Service Department,
P. O. Box 44130, Madison Wisconsin, 53744-4130; check the Constant Care section of our website,
subzero.com, or call 800-222-7820.
* Stainless Steel (classic, platinum and carbon) doors, panels, product frames and stainless interior
surfaces are covered by a limited 60 day parts and labor warranty for cosmetic defects.
* Replacement water filter cartridges are not covered by the product warranty.
77
SUB-ZERO OUTDOOR PRODUCTS
LIMITED WARRANTY
RESIDENTIAL USE ONLY
FULL FIVE YEAR SEALED SYSTEM WARRANTY
FULL ONE YEAR WARRANTY ON TOTAL PRODUCT*
FULL FIVE YEAR SEALED SYSTEM WARRANTY
For five years from the date of original installation, your Sub-Zero warranty covers all parts and labor
to repair or replace any components that prove to be defective in materials or workmanship in the
sealed system. The sealed system consists of the compressor, condenser, evaporator, drier and all
connecting tubing.
FULL ONE YEAR WARRANTY*
For one year from the date of original installation, your Sub-Zero warranty covers all parts and labor
to repair or replace any part of the product which proves to be defective in materials or workmanship.
TERMS APPLICABLE TO EACH WARRANTY
All service provided by Sub-Zero under the above warranty must be performed by an authorized
Sub-Zero service center, unless otherwise specified by Sub-Zero. Service will be provided in the
home during the normal business hours. This warranty applies only to products installed for normal
residential use. Details regarding a non-residential warranty are available upon request.
The warranty applies only to products installed in any one of the fifty states of the United States,
the District of Columbia or the ten provinces of Canada. This warranty does not cover any parts or
labor to correct any defect caused by negligence, accident or improper use, maintenance, installation, service or repair, including but not limited to improper removal and reinstallation (whether in
the unit or at a remote location) of the condensing unit.
THE REMEDIES DESCRIBED ABOVE FOR EACH WARRANTY ARE THE ONLY ONES THAT
SUB-ZERO WILL PROVIDE, EITHER UNDER THESE WARRANTIES OR UNDER ANY WARRANTY
ARISING BY OPERATION OF LAW. SUB-ZERO WILL NOT BE RESPONSIBLE FOR ANY CONSEQUENTIAL OR INCIDENTAL DAMAGES ARISING FROM THE BREACH OF THESE WARRANTIES
OR ANY OTHER WARRANTIES, WHETHER EXPRESS, IMPLIED OR STATUTORY.
Some states do not allow the exclusion or limitation of incidental or consequential damages, so the
above limitation or exclusion may not apply to you. This warranty gives you specific legal rights and
you may also have other legal rights which vary from state to state.
To receive parts and/or service and the name of the Sub-Zero authorized service center nearest
you, contact your Sub-Zero dealer, distributor or the Sub-Zero Customer Service Department,
P. O. Box 44130, Madison Wisconsin, 53744-4130; check the Constant Care section of our website,
subzero.com, or call 800-222-7820.
*Stainless Steel (classic finish) doors, panels, product frames and stainless interior surfaces are
covered by a limited 60 day parts and labor warranty for cosmetic defects.
78
The information and images in this guide are the
copyright property of Sub-Zero, Inc. Neither this
book nor any information or images contained herein
may be copied or used in whole or in part without
the express written permission of Sub-Zero, Inc.
©Sub-Zero, Inc. all rights reserved.
SUB-ZERO, INC.
P. O. BOX 44130
MADISON, WI 53744 -4130
800.222.7820
SUBZERO.COM
3758546 REV-D
8 / 2007
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement