Compaq SROM Mini-Debugger, AlphaPC 264DP, 164SX, 164LX AlphaPC Motherboard User’s Guide

PDF
Dokument
Reklama
Alpha Microprocessors
SROM Mini-Debugger
User’s Guide
Order Number: EC–QHUXD–TE
Revision/Update Information:
Compaq Computer Corporation
This is a revised document. It
supersedes the Alpha Microprocessors
SROM Mini-Debugger User’s Guide
(EC–QHUXC–TE).
April 1999
The information in this publication is subject to change without notice.
COMPAQ COMPUTER CORPORATION SHALL NOT BE LIABLE FOR TECHNICAL OR EDITORIAL
ERRORS OR OMISSIONS CONTAINED HEREIN, NOR FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES RESULTING FROM THE FURNISHING, PERFORMANCE, OR USE OF THIS MATERIAL. THIS
INFORMATION IS PROVIDED “AS IS” AND COMPAQ COMPUTER CORPORATION DISCLAIMS ANY
WARRANTIES, EXPRESS, IMPLIED OR STATUTORY AND EXPRESSLY DISCLAIMS THE IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR PARTICULAR PURPOSE, GOOD TITLE AND AGAINST
INFRINGEMENT.
This publication contains information protected by copyright. No part of this publication may be photocopied or
reproduced in any form without prior written consent from Compaq Computer Corporation.
&copy; 1999 Digital Equipment Corporation.
All rights reserved. Printed in U.S.A.
The software described in this publication is furnished under a license agreement or nondisclosure agreement. The
software may be used or copied only in accordance with the terms of the agreement.
COMPAQ, the Compaq logo, and the Digital logo Registered in U.S. Patent and Trademark Office.
AlphaPC and Tru64 are trademarks of Compaq Computer Corporation.
Windows NT is a registered trademark of Microsoft Corporation.
Intel is a registered trademark of Intel Corporation.
Other product names mentioned herein may be the trademarks of their respective companies.
9 April 1999
Contents
Preface
1
Introduction
1.1
1.2
2
Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
General Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Getting Started
2.1
2.2
2.3
2.4
2.4.1
2.4.2
2.4.3
2.4.4
2.4.4.1
2.5
2.5.1
2.6
3
1–1
1–1
Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Hardware Required . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Hardware Debug Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Setting Up the SROM Serial Port Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Connecting the Motherboard to a Terminal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Connecting the Motherboard to a Personal Computer . . . . . . . . . . . . . . . . . . . . . . . . . .
Connecting to the Motherboard from a System Running Windows NT Version 4.0 . . .
Connecting to the Motherboard from a System Running Tru64 UNIX . . . . . . . . . . . . . .
Connecting to a Serial Port Under Tru64 UNIX . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Starting and Running the Mini-Debugger . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Default Conditions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Onboard Machine Check Handler . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2–1
2–1
2–1
2–2
2–2
2–2
2–2
2–3
2–4
2–4
2–4
2–4
SROM Mini-Debugger Command Set
3.1
3.2
3.3
3.4
3.4.1
3.4.2
3.4.3
3.4.4
3.4.5
3.4.6
3.4.7
3.4.8
3.4.9
3.4.10
3.4.11
3.4.12
3.4.13
3.4.14
3.4.15
9 April 1999
Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Command and User Interface Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Command Summary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
User Commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
!d — Set Negate Data Flag . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
ba — Set Base Address Flag . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
bm — Read Data from Block of Memory . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
cm — Compare Memory Sections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
cp — Copy Data Between Memory Sections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
dc — Deposit CPU Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
di — Display Data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
dm — Deposit Memory . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
ec — Examine CPU Registers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
em — Examine Memory . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
fl — Display Flags . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
fm — Fill Memory . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
fr — Set Follow-with-Read Flag . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
fw — Set Follow-with-Write Flag . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
lo — Set Loop Flag . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3–1
3–1
3–2
3–3
3–4
3–6
3–7
3–8
3–9
3–10
3–12
3–13
3–14
3–16
3–17
3–18
3–20
3–23
3–25
iii
3.4.16
3.4.17
3.4.18
3.4.19
3.4.20
3.4.21
3.4.22
3.4.23
3.4.24
A
mt — Memory Test . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
pr — Print Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
qw — Set Quadword Data Flag . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
rt — Return to Calling Program (Exit Mini-Debugger). . . . . . . . . . . . . . . . . . . . . . . . . . .
sb — Set Base Address . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
st — Start Image Execution . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
wa — Set Write Address Flag . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
xb — External Boot . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
xm — External Image to Memory . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3–26
3–27
3–28
3–29
3–30
3–32
3–33
3–35
3–36
Support
A.1
A.2
Customer Support . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Alpha Documentation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
A–1
A–1
Index
iv
9 April 1999
Tables
3–1
3–2
3–3
9 April 1999
Command Summary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
CPU Register Names for the dc Command . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
CPU Register Names for the ec Command . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3–2
3–10
3–14
v
Preface
Introduction
This document describes how to use the Alpha Microprocessors SROM Mini-Debugger
(also referred to as the mini-debugger) to debug hardware with one of the following
motherboards:
•
AlphaPC 264DP Motherboard
•
AlphaPC 164SX Motherboard
•
AlphaPC 164LX Motherboard
Audience
This document is for anyone who develops hardware to be used with an Alpha microprocessor.
Content Overview
The information in this document is organized as follows:
9 April 1999
•
Chapter 1 is a general overview of the mini-debugger.
•
Chapter 2 describes how to set up and start the mini-debugger.
•
Chapter 3 describes the mini-debugger command set.
•
Appendix A contains information about customer support and associated documentation.
vii
Conventions
The following conventions are used in this document:
viii
Convention
Meaning
A percent sign (%)
Indicates a Tru64 UNIX operating system command prompt.
SROM&gt;
Indicates an Alpha Microprocessors SROM Mini-Debugger
prompt.
Boldface type
Indicates a command or an example of user input.
Italic type
Indicates special emphasis or the title of a manual.
Monospaced type
Indicates an operating system command, a file name, or a directory
path name.
Note
Provides general information.
9 April 1999
1
Introduction
1.1 Overview
The Alpha Microprocessors SROM Mini-Debugger provides basic hardware
debugging capability through the SROM serial port of the Alpha microprocessor.
Using only an SROM containing the mini-debugger, a clock source, a CPU chip, and a
few gates, you can exercise the device connected to the CPU to debug cache, memory,
and I/O subsystems until the board is functional enough to support a more fully featured
monitor.
1.2 General Features
The mini-debugger has the following features:
9 April 1999
•
Basic hardware debugging capability
•
A monitor that can point to hardware addresses and exercise them
•
The ability to examine and deposit memory
•
A case-independent command language
•
Support for variable baud rates and processor speeds
Introduction
1–1
2
Getting Started
2.1 Overview
The Alpha Microprocessors Motherboard Software Design Tool Kit (Alpha SDK)
includes the Alpha Microprocessors SROM Mini-Debugger binary files suitable for
programming an SROM. For information about how to program an SROM, refer to
your ROM programmer manual.
After the SROM is programmed, it can be placed into the SROM socket on the
motherboard. In addition, the mini-debugger is also available in the standard SROM
provided with the Alpha microprocessor motherboards. It can be invoked after the
standard SROM has completed CPU and system initialization and before it begins
execution of the image loaded from ROM. Refer to the Alpha motherboard user’s guide
for more information about how to access the mini-debugger and setting the required
jumper.
2.2 Hardware Required
To run the mini-debugger, you need the following items:
•
An Alpha microprocessor motherboard or a system based on the Alpha
microprocessor architecture with a connection from the microprocessor SROM
interface to the host system’s serial port (for example, an RS-232)
•
A host system (a terminal or workstation)
•
An SROM containing the SROM Mini-Debugger image
2.3 Hardware Debug Features
The mini-debugger image is loaded into the CPU’s instruction cache at reset through
the CPU’s SROM interface. The mini-debugger provides commands to:
9 April 1999
•
Examine and deposit data in memory.
•
Test memory.
•
Examine and deposit internal CPU registers.
•
Load an image into the motherboard’s memory and transfer execution to it.
Getting Started
2–1
Setting Up the SROM Serial Port Connection
The mini-debugger’s primary purpose is to debug hardware so that the memory
interface works, thus allowing a more complex debugger such as the Alpha
Microprocessors Debug Monitor to be loaded to debug other parts of the system or
software.
2.4 Setting Up the SROM Serial Port Connection
To use the mini-debugger, you must first establish a connection from your Alpha
microprocessor system or motherboard to the serial port on your host system. This
section describes how to connect the SROM serial port of a motherboard to the
following hardware:
•
A terminal
•
A PC running communication software
•
A system running Windows NT
•
An Alpha system running Tru64 UNIX
2.4.1 Connecting the Motherboard to a Terminal
To connect a motherboard to a terminal, connect the SROM serial port of the
motherboard to the terminal communication line.
Set terminal settings as shown in the following table:
Terminal Setting
Value
Terminal emulation
VT100
Transmit/receive speed
9600 baud
Data bits
8
Parity
None
Stop bits
1
2.4.2 Connecting the Motherboard to a Personal Computer
You can also use communication (terminal emulation) software running on a PC to
communicate with the motherboard. To connect the motherboard to a PC, connect the
terminal communication line to the SROM serial port of the motherboard as described
for the terminal.
2.4.3 Connecting to the Motherboard from a System Running
Windows NT Version 4.0
A system running the Windows NT version 4.0 operating system supports serial
communication with the motherboard. Use the Start button on the taskbar to configure a
COM port for connection to the motherboard and follow these steps:
1. Choose the Programs menu.
2. Choose the Accessories menu.
2–2
Getting Started
9 April 1999
Setting Up the SROM Serial Port Connection
3. Choose the HyperTerminal menu and choose the HyperTerminal icon.
The Connection Description window appears.
4. Enter a name for the new connection such as Direct Connection Com1,
choose an icon for the connection, and click OK.
5. Set the following terminal characteristics:
Terminal Setting
Value
Bits per second
9600
Data bits
8
Parity
None
Stop bits
1
Flow control
None
Click OK to save these settings. The motherboard connection appears in the
HyperTerminal window.
2.4.4 Connecting to the Motherboard from a System Running Tru64 UNIX
An Alpha system running the Tru64 UNIX operating system supports serial
communication through two ports that can be connected to the motherboard:
•
/dev/tty00
•
/dev/tty01
All examples and command descriptions that follow assume that the motherboard
SROM port is connected to port /dev/tty00.
To enable these ports for use with the motherboard, follow these steps:
1. Log in as superuser.
2. Modify the following two files:
/etc/remote
/etc/inittab
a. Add the following two lines to the /etc/remote file. These lines define a
device to connect to when using the Tru64 UNIX tip command.
port_name0:dv=/dev/tty00:br#9600:pa=none:
port_name1:dv=/dev/tty01:br#9600:pa=none:
The port_name refers to an arbitrary name that you assign to that port.
b. Modify the /etc/inittab file to disable logins on the two serial
communication ports by setting the third field to off. For example, modify
the tty00 and tty01 lines as follows:
tty00:23:off:/usr/sbin/getty /dev/tty00 9600
tty01:23:off:/usr/sbin/getty /dev/tty01 9600
9 April 1999
Getting Started
2–3
Starting and Running the Mini-Debugger
3. Reboot the system, or issue the following command to ensure that the modified
files take effect:
#
/sbin/init q
2.4.4.1 Connecting to a Serial Port Under Tru64 UNIX
After you modify the /etc/remote and /etc/inittab files, you can connect
to the serial port under the Tru64 UNIX operating system using the Tru64 UNIX tip
command. If the connection is successful, the mini-debugger prompt displays after you
press a key. For example:
% tip port_name0
! key is pressed.
SROM&gt;
Type ~. to exit the Tru64 UNIX tip command.
2.5 Starting and Running the Mini-Debugger
After the SROM serial port connection has been made, you can initialize the
mini-debugger by typing an ASCII character. This returns an SROM&gt; prompt, which
indicates that you are ready to begin debugging hardware, and displays the minidebugger version number.
For example:
U
V00000801
SROM&gt;
Once an ASCII character is typed, the mini-debugger automatically detects the baud
rate of the terminal connected to the SROM serial port. Baud rates up to 19.2K are supported.
2.5.1 Default Conditions
If you are using the mini-debugger built into the standard Alpha motherboard SROM,
then the proper initialization conditions are automatically set. When you see the minidebugger prompt, the system has been initialized.
The example shown in Section 3.4, the xm command, demonstrates how to load and
execute the Debug Monitor.
2.6 Onboard Machine Check Handler
The onboard machine check handler is useful in debugging certain memory faults. You
must set bit [1] of the ABOX_CTL register to enable machine checks. For 21164-based
boards, machine checks are always enabled. When a machine check is encountered, as
it might be in a read, the machine check handler prints the following message followed
by the SROM&gt; prompt:
2–4
Getting Started
9 April 1999
Onboard Machine Check Handler
MCHK
Abox
Icsr
PalB
ExAd
DcSt
Hirr
Hier
BCtl
BiSt
BiAd
Syn
FiAd
00000000.00000002
00000000.00ff0000
00000000.00000000
00000000.00200cb4
00000000.0000000b
00000000.00000000
00000000.00001890
000007f8.00000000
00000000.000010c1
00000001.e0000018
00000000.00000000
00000000.00200950
SROM&gt;
9 April 1999
Getting Started
2–5
3
SROM Mini-Debugger Command Set
3.1 Overview
This chapter describes the Alpha Microprocessors SROM Mini-Debugger command
set.
3.2 Command and User Interface Features
The following list describes some of the features of the mini-debugger command language:
9 April 1999
•
Uppercase or lowercase characters can be used interchangeably.
•
Only the first two characters of a command line are significant; the rest are ignored.
•
Numbers are input and output in hexadecimal format.
•
Commands can be aborted at any time by pressing Ctrl/C (except for the xm command).
•
For commands that prompt for input, pressing Return on an empty line defaults to a
value of 0.
•
In qw data mode, addresses are aligned to a quadword boundary (the three least significant bits of the addresses are zero). In all other modes, addresses are aligned to a
longword boundary (the two least significant bits of the addresses are zero).
•
In qw data mode, all reads and stores are performed using ldq/p and stq/p instructions, respectively. In all other modes, reads and stores use ldl/p and stl/p instructions, respectively.
•
All stores are followed with two MB instructions. This keeps writes ordered (from
the system’s point of view) and prevents merging in the write queue. For more
information on the MB instruction, see the CPU’s hardware reference manual.
•
For commands that use an address range, the ending address is not included in the
range. The last read or store is performed in the immediately preceding quadword
or longword, depending on the state of the qw data flag.
SROM Mini-Debugger Command Set
3–1
Command Summary
3.3 Command Summary
Table 3–1 summarizes the command set for the Alpha Microprocessors SROM MiniDebugger. These commands are described in the following sections.
Table 3–1 Command Summary
Command
Description
Flag Commands
!d
Enable/disable negation of data to be written.
ba
Enable/disable use of base address.
di
Enable/disable display to screen.
fr
Enable/disable follow-with-read flag.
fw
Enable/disable follow-with-write flag.
lo
Enable/disable command repetition.
qw
Enable/disable quadword mode operations.
wa
Enable/disable write address mode.
Memory Commands
bm
Read block of memory addresses.
cm
Compare two sections of memory.
cp
Copy a block of memory.
fm
Fill memory range with data pattern.
mt
Perform simple memory test.
Deposit/Examine Commands
dc
Deposit internal CPU register.
dm
Deposit data to memory location.
ec
Examine internal CPU registers.
em
Examine data in a memory location.
Print Commands
fl
Print current state of flags.
pr
Print contents of general-purpose CPU registers.
Load/Execute Commands
rt
Exit mini-debugger.
st
Start executing at specified address.
xb
Begin execution of the last image loaded.
xm
Load external image to memory.
Miscellaneous Command
sb
3–2
Set base address.
SROM Mini-Debugger Command Set
9 April 1999
User Commands
3.4 User Commands
This section contains a complete description and examples of the SROM
Mini-Debugger commands. The commands are listed in alphabetical order. The Control Flags section in each command description lists the flags that affect the behavior of
the command if the flag is enabled.
9 April 1999
SROM Mini-Debugger Command Set
3–3
User Commands
3.4.1 !d — Set Negate Data Flag
The negate data (!d) command enables or disables the use of the one’s complement of
the data to be written by toggling the negate data flag.
Control Flags
Not applicable.
Description
With the negate data flag enabled, writes will use the complement (negation) of the data
specified by the user or automatically generated by the command in use.
The default state is off.
Example
In the following example, with the negate data flag enabled, the data supplied by the
user (0) is complemented and written to address 500000.
SROM&gt; !d
Neg Data ON
SROM&gt; dm
A&gt; 500000
D&gt; 0
SROM&gt; em
A&gt; 500000
00000000.00500000: ffffffff
With the fill memory command, the data written with each write is also complemented,
resulting in every other write having the original data.
SROM&gt; fm
A&gt; 600000
A&gt; 600020
D&gt; ffff0000
SROM&gt; bm
A&gt; 600000
A&gt; 600020
00000000.00600000:
00000000.00600004:
00000000.00600008:
00000000.0060000c:
00000000.00600010:
00000000.00600014:
00000000.00600018:
00000000.0060001c:
0000ffff
ffff0000
0000ffff
ffff0000
0000ffff
ffff0000
0000ffff
ffff0000
If the write address flag is also enabled, then data written is the complement of the destination address.
3–4
SROM Mini-Debugger Command Set
9 April 1999
User Commands
SROM&gt; wa
Wrt Addr ON
SROM&gt; fm
A&gt; 500000
A&gt; 500010
SROM&gt; bm
A&gt; 500000
A&gt; 500010
00000000.00500000:
00000000.00500004:
00000000.00500008:
00000000.0050000c:
9 April 1999
ffafffff
ffaffffb
ffaffff7
ffaffff3
! This is the complement of x500000.
SROM Mini-Debugger Command Set
3–5
User Commands
3.4.2 ba — Set Base Address Flag
The set base address (ba) flag command enables or disables the base address flag,
which must be enabled to use the set base (sb) command. The ba command toggles the
base address flag.
Control Flags
Not applicable.
Description
When the base address flag is enabled, the address entered with the sb command is
added to addresses entered in any subsequent examine or deposit command.
The default state is off.
Example
To access addresses in the range 3.FFF80000 to 3.FFFFFFFF, it may be more convenient to enter its base address and work with offsets, rather than typing the absolute
address every time.
SROM&gt; sb
A&gt; 3fff80000
00000003.fff80000
BaseAddr ON
SROM&gt; bm
A&gt; 0
A&gt; 10
00000003.fff80000:
00000003.fff80004:
00000003.fff80008:
00000003.fff8000c:
5a5ac3c3
a5a53c3c
00000038
00006579
SROM&gt; ba
00000003.fff80000
BaseAddr OFF
SROM&gt; em
A&gt; 400000
00000000.00400000: 00400000
SROM&gt; ba
0000003.fff80000
BaseAddr ON
SROM&gt; bm
A&gt; 30
A&gt; 40
00000003.fff80030:
00000003.fff80034:
00000003.fff80038:
00000003.fff8003c:
3–6
00000001
0000be8a
47ff041f
47ff041f
SROM Mini-Debugger Command Set
9 April 1999
User Commands
3.4.3 bm — Read Data from Block of Memory
The block memory (bm) command displays the data read from a specified range of
addresses.
Control Flags
ba (base address flag)
di (display flag)
fr (follow-with-read flag)
fw (follow-with-write flag)
lo (loop flag)
qw (quadword data flag)
Description
The block memory command reads data from a block of memory locations and prints it
out to the screen if the display flag is enabled. The range is specified by first entering
the starting address, followed by the ending address.
Example
The following example shows a block memory command display:
SROM&gt; wa
Wrt Addr ON
! Data for fill memory command.
SROM&gt; qw
QW ON
! Use quadword writes and 64-bit data.
SROM&gt; fm
A&gt; 400000
A&gt; 400010
! Fill range with its own address.
SROM&gt; bm
! Display range.
A&gt; 400000
A&gt; 400010
00000000.00400000: 00000000.00400000
00000000.00400008: 00000000.00400008
9 April 1999
SROM Mini-Debugger Command Set
3–7
User Commands
3.4.4 cm — Compare Memory Sections
The compare (cm) command compares two sections of memory and displays any differences.
Control Flags
ba (base address flag)
lo (loop flag)
qw (quadword data flag)
Description
The compare command checks the equality of two blocks of memory and prints any
differences. The first two addresses specify the starting and ending addresses of the
first block to be checked and the third input provides the starting address of the second
block.
Example
In the following example, two blocks are filled with the same data and then two locations are changed. The compare command shows those two locations as having different data, even though the display flag is disabled.
3–8
SROM&gt; fm
A&gt; 500000
A&gt; 500020
D&gt; 12345678
! Fill the first block with a known pattern.
SROM&gt; fm
A&gt; 600000
A&gt; 600020
D&gt; 12345678
! Fill the second block with a known pattern.
SROM&gt; dm
A&gt; 600004
D&gt; bad
! Change first location.
SROM&gt; dm
A&gt; 60000c
D&gt; deed
! Change second location.
SROM&gt; di
Disp OFF
! Does not affect the compare command.
SROM&gt; cm
A&gt; 500000
A&gt; 500020
A&gt; 600000
00000000.00500004:
00000000.00600004:
00000000.0050000c:
00000000.0060000c:
! Compare both sections.
12345678
00000bad
12345678
0000deed
SROM Mini-Debugger Command Set
9 April 1999
User Commands
3.4.5 cp — Copy Data Between Memory Sections
The copy (cp) command reads data from a range of addresses and writes it to another
address.
Control Flags
ba (base address flag)
lo (loop flag)
qw (quadword data flag)
Description
The copy command moves sections of data from one place in memory to another. The
first two addresses specify the starting and ending addresses of the block to be moved.
The third input provides the destination address for the copy.
Example
In the following example, a block starting at 400000 is filled with its own addresses and
then copied to 500000:
9 April 1999
SROM&gt; wa
Wrt Addr ON
! Use the address as the data for the writes.
SROM&gt; fm
A&gt; 400000
A&gt; 400020
! Fill this block with its own addresses.
SROM&gt; cp
A&gt; 400000
A&gt; 400020
A&gt; 500000
! Copy the block to 500000.
SROM&gt; bm
A&gt; 500000
A&gt; 500010
00000000.00500000:
00000000.00500004:
00000000.00500008:
00000000.0050000c:
! This shows the data was moved to 500000.
00400000
00400004
00400008
0040000c
SROM Mini-Debugger Command Set
3–9
User Commands
3.4.6 dc — Deposit CPU Register
The deposit CPU register (dc) command changes the contents of internal CPU registers.
Control Flags
Not applicable.
Description
The deposit CPU register command changes the contents of internal CPU registers.
These registers are CPU dependent, so command input is different for each Alpha CPU.
Table 3–2 show the names assigned by the mini-debugger to the CPU registers; these
are the only valid names that may be entered at the IPR prompt.
Table 3–2 CPU Register Names for the dc Command
Mini-Debugger Name
CPU Register Name
Description
21264
3–10
Cc
CC
Cycle counter
Va
VA
Virtual address
Vafo
VA_FORM
Virtual address format
ExCa
EXC_ADDR
Exception address
Ivaf
IVA_FORM
Instruction VA format
Ps
PS
Processor status
Ier
IER
Interrupt enable
Ierc
IER_CM
Interrupt enable and current mode
Sirr
SIRR
Software interrupt request
Isum
ISUM
Interrupt summary
Excs
EXC_SUM
Exception summary
PalB
PAL_BASE
PAL base address
Ictl
I_CTL
Ibox control
Pctr
PCTR_CTL
Performance counter control
Ista
I_STAT
Ibox status
Asn
ASN
Address space number
Aste
ASTE
AST enable register
Astr
ASTR
AST request register
Ppce
PPCE
Process performance counting enable
Fpe
FPE
Floating-point enable
Mmst
MM_STAT
Memory management status
Dcst
DC_STAT
Dcache status
SROM Mini-Debugger Command Set
9 April 1999
User Commands
Table 3–2 CPU Register Names for the dc Command (Continued)
Mini-Debugger Name
CPU Register Name
Description
21164
BCtl*
BC_CONTROL
Bcache control
BCfg*
BC_CONFIG
Bcache configuration
Icsr
ICSR
Ibox control and status
PalB
PAL_BASE
PAL base address
DcMd
DC_MODE
Dcache mode
Ipl
IPLR
Interrupt priority level
* Write-only registers whose values are obtained from a copy placed in PALtemp registers 1
and 2 when they were written with the dc command. Therefore, changing these internal CPU
registers overwrites the saved contents of the general-purpose CPU registers 1 and 2 (also
stored in PALtemp 1 and 2), affecting the output of the pr command.
Example
In the following example, output on a DP264 CPU is displayed:
SROM&gt; dc
! Enable machine checks and CRD interrupts.
IPR&gt; ictl
D&gt; 3506386
*ICTL
00000000.03506386
SROM&gt; ec
Cc
00000000.0000b78d
Va
00000800.7ffffffc
Vafo
00000002.001ffff8
ExCa
00000000.00203ee8
Ivaf
00000000.00000000
Ps
00000001.00000000
Ier
00000001.00000000
Ierc
00000001.00000000
Sirr
00000000.00000000
Isum
00000000.00000000
Excs
00000000.00001fc0
PalB
00000000.00000000
Ictl
00000000.03506386
Pctr
00000000.10000040
Ista
00000000.00000000
Asn
00000000.00000004
Aste
00000000.00000004
Astr
00000000.00000004
Ppce
00000000.00000004
Fpe
00000000.00000004
Mmst
00000000.000002c1
Dcst
00000000.00000000
9 April 1999
SROM Mini-Debugger Command Set
3–11
User Commands
3.4.7 di — Display Data
The display (di) command enables or disables the display of data to the screen by toggling the display flag.
Control Flags
Not applicable.
Description
When the display flag is enabled, the examine commands print the data obtained. When
it is disabled, the read operations still take place but the data is not displayed — not
even errors. The cm and mt commands, which produce read operations of their own,
ignore the state of this flag and always display the data if there is a mismatch.
The default state is on.
Example
In the following example, the em command performs a read operation and displays the
data read in because the display flag is enabled. However, when the flag is disabled, the
read operations performed by the bm command are not echoed to the screen.
SROM&gt; em
A&gt; 500000
00000000.00500000: ffffffff
SROM&gt; di
Disp OFF
SROM&gt; bm
A&gt; 500000
A&gt; 500010
The next example shows that the cm command is not affected by this flag’s state and
prints out data whenever a mismatch occurs.
SROM&gt; di
Disp OFF
SROM&gt; cm
A&gt; 500000
A&gt; 500010
A&gt; 600000
00000000.00500000:
00000000.00600000:
00000000.00500004:
00000000.00600004:
00000000.00500008:
00000000.00600008:
00000000.0050000c:
00000000.0060000c:
3–12
ffffffff
0000ffff
000f0000
ffff0000
000f0000
0000ffff
000f0000
ffff0000
SROM Mini-Debugger Command Set
9 April 1999
User Commands
3.4.8 dm — Deposit Memory
The deposit memory (dm) command writes a data pattern to one memory location.
Control Flags
!d (negate data flag)
ba (base address flag)
fr (follow-with-read flag)
fw (follow-with-write flag)
lo (loop flag)
qw (quadword data flag)
wa (write address flag)
Description
The deposit memory command writes a data pattern to the specified memory location.
If the quadword data flag is enabled, then 64 bits of data are written; otherwise, only 32
bits of data are used. The data pattern is provided by the user but can be affected by the
state of the write address flag and the negate data flag.
Example
In this example, a continuous write to address 500000 is performed with the loop flag
enabled. Note that because the quadword data flag is disabled, only the low 32 bits of
the data pattern entered are written.
SROM&gt; di
Disp ON
! Enable display mode.
SROM&gt; qw
QW OFF
! Writes are performed 32 bits at a time.
SROM&gt; lo
Loop ON
! Repeat operation until a key is pressed.
SROM&gt; dm
A&gt; 500000
D&gt; 123456789abcdef
! Only the low 32-bits are used in these writes.
! (key pressed)
SROM&gt; em
! Examine contents of address 500000.
A&gt; 500000
00000000.00500000: 89abcdef
00000000.00500000: 89abcdef
00000000.00500000: 89abcdef
! (key pressed)
9 April 1999
SROM Mini-Debugger Command Set
3–13
User Commands
3.4.9 ec — Examine CPU Registers
The examine CPU registers (ec) command prints the contents of internal CPU registers.
Control Flags
Not applicable.
Description
The examine CPU registers command displays the contents of internal CPU registers.
These registers are CPU dependent, so command output is different for each Alpha
CPU. Table 3–3 show the names assigned by the mini-debugger to the CPU registers.
Table 3–3 CPU Register Names for the ec Command
Mini-Debugger Name
CPU Register Name
Description
21264
3–14
Cc
CC
Cycle counter
Va
VA
Virtual address
Vafo
VA_FORM
Virtual address format
ExCa
EXC_ADDR
Exception address
Ivaf
IVA_FORM
Instruction VA format
Ps
PS
Processor status
Ier
IER
Interrupt enable
Ierc
IER_CM
Interrupt enable and current mode
Sirr
SIRR
Software interrupt request
Isum
ISUM
Interrupt summary
Excs
EXC_SUM
Exception summary
PalB
PAL_BASE
PAL base address
Ictl
I_CTL
Ibox control
Pctr
PCTR_CTL
Performance counter control
Ista
I_STAT
Ibox status
Asn
ASN
Address space number
Aste
ASTE
AST enable register
Astr
ASTR
AST request register
Ppce
PPCE
Process performance counting enable
Fpe
FPE
Floating-point enable
Mmst
MM_STAT
Memory management status
Dcst
DC_STAT
Dcache status
SROM Mini-Debugger Command Set
9 April 1999
User Commands
Table 3–3 CPU Register Names for the ec Command (Continued)
Mini-Debugger Name
CPU Register Name
Description
21164
BCtl*
BC_CONTROL
Bcache control
BCfg*
BC_CONFIG
Bcache configuration
Icsr
ICSR
Ibox control and status
PalB
PAL_BASE
PAL base address
ExAd
EXC_ADDR
Exception address
Ipl
IPLR
Interrupt priority level
Int
INTID
Interrupt ID
Isr
ISR
Interrupt summary
IcPE
ICPERR_STAT
Icache parity error status
DcMd
DC_MODE
Dcache mode
DcPE
DC_PERR_STAT
Dcache parity error status
* Write-only registers whose values are obtained from a copy placed in PALtemp registers 1 and
2 when they were written with the dc command. Therefore, changing these internal CPU registers overwrites the saved contents of the general-purpose CPU registers 1 and 2 (also stored
in PALtemp 1 and 2), affecting the output of the pr command.
Example
The following example shows the output of an ec command on a DP264 CPU:
SROM&gt; ec
Cc
00000000.0000b78d
Va
00000800.7ffffffc
Vafo
00000002.001ffff8
ExCa
00000000.00203ee8
Ivaf
00000000.00000000
Ps
00000001.00000000
Ier
00000001.00000000
Ierc
00000001.00000000
Sirr
00000000.00000000
Isum
00000000.00000000
Excs
00000000.00001fc0
PalB
00000000.00000000
Ictl
00000000.03506386
Pctr
00000000.10000040
Ista
00000000.00000000
Asn
00000000.00000004
Aste
00000000.00000004
Astr
00000000.00000004
Ppce
00000000.00000004
Fpe
00000000.00000004
Mmst
00000000.000002c1
Dcst
00000000.00000000
9 April 1999
SROM Mini-Debugger Command Set
3–15
User Commands
3.4.10 em — Examine Memory
The examine memory (em) command reads data from one memory location.
Control Flags
!d (negate data flag)
ba (base address flag)
di (display flag)
fr (follow-with-read flag)
fw (follow-with-write flag)
lo (loop flag)
qw (quadword data flag)
Description
The examine memory command reads data from the specified memory location and
displays it on the screen if the display (di) flag is enabled. Depending on the state of
the quadword data flag, 32 or 64 bits will be displayed.
Example
The following example shows output from an em command:
3–16
SROM&gt; di
Disp ON
! Enable display mode.
SROM&gt; qw
QW ON
! Reads are performed 64 bits at a time.
SROM&gt; lo
Loop ON
! Repeat operation until a key is pressed.
SROM&gt; em
A&gt; 3fff80000
00000003.fff80000:
00000003.fff80000:
00000003.fff80000:
00000003.fff80000:
00000003.fff80000:
! Repeat read until a key is pressed.
a5a53c3c.5a5ac3c3
a5a53c3c.5a5ac3c3
a5a53c3c.5a5ac3c3
a5a53c3c.5a5ac3c3
a5a53c3c.5a5ac3c3
! (key pressed)
SROM Mini-Debugger Command Set
9 April 1999
User Commands
3.4.11 fl — Display Flags
The flags (fl) command displays the current state of all flags.
Control Flags
Not applicable.
Description
The behavior of many of the mini-debugger commands can be affected by the state of
one or more of eight available flags. The flags command displays on the screen the current state of these flags.
Example
In the following example, the default state of all flags, except the display flag, is off
(disabled). Their states can be changed by issuing the appropriate command.
SROM&gt; fl
FollowWr
FollowRd
BaseAddr
Neg Data
Wrt Addr
Loop OFF
Disp ON
QW OFF
OFF
OFF
OFF
OFF
OFF
SROM&gt; wa
Wrt Addr ON
SROM&gt; !d
Neg Data ON
SROM&gt; fl
FollowWr
FollowRd
BaseAddr
Neg Data
Wrt Addr
Loop OFF
Disp ON
QW OFF
9 April 1999
OFF
OFF
OFF
ON
ON
SROM Mini-Debugger Command Set
3–17
User Commands
3.4.12 fm — Fill Memory
The fill memory (fm) command writes data to the specified range of addresses.
Control Flags
!d (negate data flag)
ba (base address flag)
fr (follow-with-read flag)
fw (follow-with-write flag)
lo (loop flag)
qw (quadword data flag)
wa (write address flag)
Description
The fill memory command writes to a range or block of memory locations. The range is
specified by first entering the starting address, followed by the ending address. The data
to be written to the entire block can be entered by the user after the ending address, or it
can be automatically generated by the command, depending on the state of the write
address and negate data flags.
Example
In this example, the starting address (400003) will be truncated to the nearest quadword
(400000) because the quadword data flag is on. The ending address (40004F) is truncated to 400048 for the same reason. Therefore, the last address written with the specified data is 400040. Similar truncations can be seen with the bm command.
SROM&gt; qw
QW ON
SROM&gt; fm
A&gt; 400003
A&gt; 40004F
D&gt; 0123456789ABCDEF
SROM&gt; bm
A&gt; 3ffff7
A&gt; 40005f
00000000.003ffff0:
00000000.003ffff8:
00000000.00400000:
00000000.00400008:
00000000.00400010:
00000000.00400018:
00000000.00400020:
00000000.00400028:
00000000.00400030:
00000000.00400040:
00000000.00400048:
00000000.00400050:
3–18
fff0ffff.fff0ff7d
fff0ffff.fff0ffff
01234567.89abcdef
01234567.89abcdef
01234567.89abcdef
01234567.89abcdef
01234567.89abcdef
01234567.89abcdef
01234567.89abcdef
01234567.89abcdef
00000000.00000000
00000000.00000000
SROM Mini-Debugger Command Set
9 April 1999
User Commands
The write address flag allows for unique data to be written to each memory location.
This can be useful in debugging memory problems.
SROM&gt; qw
QW OFF
SROM&gt; wa
Wrt Addr ON
SROM&gt; fm
A&gt; 400000
A&gt; 400020
SROM&gt; bm
A&gt; 400000
A&gt; 400024
00000000.00400000:
00000000.00400004:
00000000.00400008:
00000000.0040000c:
00000000.00400010:
00000000.00400014:
00000000.00400018:
00000000.0040001c:
00000000.00400020:
00400000
00400004
00400008
0040000c
00400010
00400014
00400018
0040001c
89abcdef
Sometimes, it is useful to have alternating patterns written to adjacent memory
locations. The negate data flag (!d) can be helpful then.
SROM&gt; !d
Neg Data ON
SROM&gt; fm
A&gt; 400000
A&gt; 400020
D&gt; 0
SROM&gt; bm
A&gt; 400000
A&gt; 400020
00000000.00400000:
00000000.00400004:
00000000.00400008:
00000000.0040000c:
00000000.00400010:
00000000.00400014:
00000000.00400018:
00000000.0040001c:
9 April 1999
ffffffff
00000000
ffffffff
00000000
ffffffff
00000000
ffffffff
00000000
SROM Mini-Debugger Command Set
3–19
User Commands
3.4.13 fr — Set Follow-with-Read Flag
The follow-with-read (fr) command toggles the follow-with-read flag, enabling or disabling the execution of a read operation after the last operation executed by a command.
Control Flags
fw (follow-with-write flag)
Description
The follow-with-read command is an advanced command whose use is required in
certain situations where a second operation is needed to achieve a desired result, such as
continuously creating a cache victim or having an I/O read operation interspersed
between memory writes. Enabling the follow-with-read flag causes a prompt for an
additional address from which the read operation is performed, unless the follow-withwrite flag is also enabled. In this case, the additional address is used for the write
operation and the read operation is performed from the first address.
The read operation takes place at the end of the command sequence, but after all read
and write operations required by the current command have executed (including any
write operations due to the follow-with-write flag being enabled). The data read may or
may not be displayed, depending on the current command.
The default state is off.
Example
In the following example, a memory hierarchy composed of a 2MB direct-mapped,
write-back, read-allocate cache and system memory is assumed. This may be the case
in a 21064-based system where the Dcache is off and an external 2MB cache is on.
To continuously write the same address and guarantee that the data makes it to the system memory and is not simply cached, you must create a victim after each write operation. To create a victim, map the read address to the same cache index as the write
operation.
For example, writing to address 0x600000 and reading from 0x800000 ejects the
cached write of address 0x600000. From the system memory’s point of view, a read of
0x800000 will be followed with a write of 0x600000, followed by another read of
0x800000 and so on until the loop is broken by pressing a key.
SROM&gt; lo
Loop ON
! Repeat command until a key is pressed.
SROM&gt; fr
FollowRd ON
! Follow deposit command with a read.
SROM&gt; di
Disp OFF
! Don’t display the data from the read.
SROM&gt; dm
A&gt; 600000
A&gt; 800000
D&gt; 0f0f0f0f
3–20
!
!
!
!
SROM Mini-Debugger Command Set
Address of write.
Address of read; a multiple of 2MB.
Data for the write.
(key pressed)
9 April 1999
User Commands
To test the data path and cache timing between the CPU and the external cache, provide
the same address for the read as the write. For example, each write operation in the
following fm command is followed with a read operation from the external cache. Note
that the read address is also incremented by the same amount as the write address.
SROM&gt; lo
Loop OFF
! Don’t repeat fill memory command.
SROM&gt; di
Disp ON
! Print the data from the reads.
SROM&gt; wa
Wrt Addr ON
! Use the address as the data for the writes.
SROM&gt; fr
FollowRd ON
! Follow deposit command with a read.
SROM&gt; fm
A&gt; 600000
A&gt; 600020
A&gt; 600000
00000000.00600000:
00000000.00600004:
00000000.00600008:
00000000.0060000c:
00000000.00600010:
00000000.00600014:
00000000.00600018:
00000000.0060001c:
! Starting address of fill memory command.
! Ending address of fill memory command.
! Address to begin reading from.
00600000
00600004
00600008
0060000c
00600010
00600014
00600018
0060001c
During the execution of the mt command, it may be desirable for a read operation to
I/O space to follow each write and read operation in the test. This could detect potential
problems in the memory controller where memory and I/O accesses are handled. This
command does not print the data from the read operation to I/O space.
SROM&gt; di
Disp ON
! Ignored by the memory test command.
SROM&gt; wa
Wrt Addr ON
! Use the address as the data for the writes.
SROM&gt; fr
FollowRd ON
! Follow deposit command with a read.
SROM&gt; mt
A&gt; 500000
A&gt; 600000
A&gt; 3fff80000
9 April 1999
! Start memory test at this address.
! End memory test at this address.
! Follow with reads beginning at this address.
SROM Mini-Debugger Command Set
3–21
User Commands
If the follow-with-write flag is also enabled, the additional address requested is used for
this write operation and the read operation is performed from the first address. In the
following example, two blocks of memory are filled with their own addresses and read
operations from the first block are displayed after each write operation to the first block.
SROM&gt; di
Disp ON
! Ignored by the memory test command.
SROM&gt; wa
Wrt Addr ON
! Use the address as the data for the writes.
SROM&gt; fw
FollowWr ON
! Follow with a write (before the read).
SROM&gt; fr
FollowRd ON
! Follow deposit command with a read.
SROM&gt; fm
A&gt; 500000
A&gt; 500020
A&gt; 600000
00000000.00500000:
00000000.00500004:
00000000.00500008:
00000000.0050000c:
00000000.00500010:
00000000.00500014:
00000000.00500018:
00000000.0050001c:
3–22
! Begin to write at this address
! and end with this one.
! Write to this address range after each
! write from first block.
00500000
! Reads from first block.
00500004
00500008
0050000c
00500010
00500014
00500018
0050001c
SROM Mini-Debugger Command Set
9 April 1999
User Commands
3.4.14 fw — Set Follow-with-Write Flag
The follow-with-write (fw) command toggles the follow-with-write flag, enabling or
disabling the execution of a write operation after the last operation executed by a command.
Control Flags
Not applicable.
Description
The follow-with-write command is an advanced command whose use is required in
certain situations where a second operation is needed to achieve a desired result, such as
continuously creating a cache victim or having an I/O write operation interspersed
between memory read operations. Enabling the follow-with-write flag causes a prompt
for an additional address to which the write will be performed.
The write operation takes place at the end of the command sequence, but before any
read operations due to the follow-with-read flag being enabled. The data used for the
write operation varies. If the write operation follows a read operation, then the data
used comes from the read operation. If the write operation follows a write operation,
then it uses the data supplied by the user or the data generated by the command (see the
wa and !d commands).
The default state is off.
Example
In the following example, the fm command writes the block beginning at 0x400000
with the specified data pattern, because the follow-with-write (fw) flag is enabled; it
also writes the same data to the block starting 0x500000. For the bm command, the
write operation gets its data from the previously executed read operations, in effect,
making this sequence a copy command.
SROM&gt; fw
FollowWr ON
SROM&gt; fm
A&gt; 400000
A&gt; 400010
A&gt; 500000
D&gt; abcdef
! Follow the last operation with a write.
! First block gets written with data pattern.
! Second block also gets written with the same data pattern.
SROM&gt; bm
A&gt; 500000
! Read from this block.
A&gt; 500010
A&gt; 600000
! Write to this block.
00000000.00500000: 00abcdef
00000000.00500004: 00abcdef
00000000.00500008: 00abcdef
00000000.0050000c: 00abcdef
9 April 1999
SROM Mini-Debugger Command Set
3–23
User Commands
SROM&gt; fw
FollowWr OFF
SROM&gt; bm
! This shows that a copy function has taken place.
A&gt; 600000
A&gt; 600010
00000000.00600000: 00abcdef
00000000.00600004: 00abcdef
00000000.00600008: 00abcdef
00000000.0060000c: 00abcdef
The following example is similar to the previous one, except that the write address (wa)
flag has been set. With wa enabled, the address is for the read data; the data is for the
write data.
SROM&gt; fw
FollowWr ON
SROM&gt; fm
A&gt; 400000
A&gt; 400010
A&gt; 500000
D&gt; abcdef
! Follow the last operation with a write.
! First block gets written with data pattern.
! Second block also gets written with the same data pattern.
SROM&gt; wa
! Write address flag is enabled.
Wrt Addr ON
SROM&gt; bm
A&gt; 500000
! Read from this block.
A&gt; 500010
A&gt; 600000
! Write to this block.
00000000.00500000: 00000000.00600000
00000000.00500008: 00000000.00600008
SROM&gt; wa
Wrt Addr OFF
3–24
SROM Mini-Debugger Command Set
9 April 1999
User Commands
3.4.15 lo — Set Loop Flag
The loop (lo) command enables or disables looping or repeating of a command by toggling the loop flag.
Control Flags
Not applicable.
Description
When the loop flag is enabled, examine and deposit commands are repeated until you
stop the looping by pressing a key. This feature is useful for hardware timing of read
and write operations to the external cache or memory system, or anytime a command
needs to be repeated continuously.
The default state is off.
Example
In the following example that shows the dm command, the data pattern is written to
address 500000 continuously until a key is pressed. The em command reads and
displays the data from address 500000 continuously until a keystroke is detected.
SROM&gt; lo
Loop ON
SROM&gt; dm
A&gt; 500000
D&gt; 12345678
! (key pressed)
SROM&gt; em
A&gt; 500000
00000000.00500000:
00000000.00500000:
00000000.00500000:
00000000.00500000:
00000000.00500000:
00000000.00500000:
00000000.00500000:
00000000.00500000:
12345678
12345678
12345678
12345678
12345678
12345678
12345678
12345678
! (key pressed)
The mt command continuously checks the range between 400000 and 500000.
SROM&gt; wa
Wrt Addr ON
SROM&gt; mt
A&gt; 400000
A&gt; 500000
!(key pressed)
9 April 1999
SROM Mini-Debugger Command Set
3–25
User Commands
3.4.16 mt — Memory Test
The memory test (mt) command performs a simple write-read-compare test.
Control Flags
!d (negate data flag)
ba (base address flag)
fr (follow-with-read flag)
fw (follow-with-write flag)
lo (loop flag)
qw (quadword data flag)
wa (write address flag)
Description
The memory test command first writes to the memory range specified with the
user-specified data or command-generated data. It then begins reading back the data
and comparing it against what was written. If a mismatch is encountered, both the read
and the expected data are displayed on the screen.
Example
In the following example, the data pattern 12345678 is written to the block starting at
400000 and ending at 600000. The range is then read back and compared with the
expected data 12345678. In this example, no mismatches are found.
SROM&gt; mt
A&gt; 400000
A&gt; 600000
D&gt; 12345678
In this next example, a bit stuck high is detected by the memory test.
SROM&gt; wa
Wrt Addr ON
! Use address of write as the data.
SROM&gt; mt
A&gt; 400000
A&gt; 500000
00000000.00400000:10400000 ! The data read back has an extra bit set.
Expect: 00400000
00000000.00400004:10400004
Expect: 00400004
00000000.00400008:10400008
Expect: 00400008
00000000.0040000c:1040000c
Expect: 0040000c
00000000.00400010:10400010
Expect: 00400010
00000000.00400014:10400014
Expect: 00400014
! A key was pressed.
3–26
SROM Mini-Debugger Command Set
9 April 1999
User Commands
3.4.17 pr — Print Register
The print register (pr) command displays the contents of the general-purpose CPU registers.
Control Flags
Not applicable.
Description
The contents of the general-purpose CPU registers are saved to PALtemp registers
when the mini-debugger is first entered. The pr command allows for their viewing.
Note that because the dc command uses two of these PALtemp registers, the results in
R1 and R2 will be changed after a dc command.
Note:
This command may not be available in all standard SROMs supplied with
the Alpha motherboards due to a lack of space. If this is the case, recompile the mini-debugger source files supplied in the Alpha SDK with the
FULL_MDBG compile switch defined to enable this command.
Example
SROM&gt; pr
R00:
00000000.00000000
R01:
00000000.00000006
R02:
000007f8.00000000
R03:
00000000.00000030
R04:
00000000.00000000
R05:
00000000.00000000
R06:
00000000.00300000
R07:
00000000.00001428
R08:
00000000.02000000
R09:
00000000.00000004
R10:
00000000.00026890
R11:
00000000.000262a0
R12:
00000000.00026560
R13:
0000004e.2001c665
R14:
00000000.00026590
R15:
00000000.000265a0
R16:
00000000.00026580
R17:
00000000.00008000
R18:
00000080.00000080
R19:
00000000.01ffdf30
R20:
ffffffff.fffdffff
R21:
00000000.00300000
R22:
0048484c.4c4e4e4e
R23:
00000000.0032edec
R24:
00000000.00000000
R25:
00000000.01ffdd25
R26:
00000000.00011fa8
R27:
00000000.00200080
R28:
00000000.0007a900
R29:
00000000.0007ce50
R30:
00000000.01ffdf30
9 April 1999
SROM Mini-Debugger Command Set
3–27
User Commands
3.4.18 qw — Set Quadword Data Flag
The quadword (qw) command enables or disables the quadword data flag.
Control Flags
Not applicable.
Description
The quadword command changes the state of the quadword data flag. When the quadword data flag is enabled, all operations are performed on 64-bit data. When off, only
32 bits of data are used.
The default state is off.
Example
In this example, the first bm command loads 32 bits of data using the ldl/p instruction
from addresses 3.FFF80000, 3.FFF80004, 3.FFF80008, and 3.FFF8000C. After
quadword mode is enabled, the same command performs only two 64-bit loads of data
using the ldq/p instruction from addresses 3.FFF80000 and 3.FFF80008.
SROM&gt; bm
A&gt; 3fff80000
A&gt; 3fff80010
00000003.fff80000:
00000003.fff80004:
00000003.fff80008:
00000003.fff8000c:
5a5ac3c3
a5a53c3c
00000038
00006579
SROM&gt; qw
QW ON
SROM&gt; bm
A&gt; 3fff80000
A&gt; 3fff80010
00000003.fff80000: a5a53c3c.5a5ac3c3
00000003.fff80008: 00006579.00000038
3–28
SROM Mini-Debugger Command Set
9 April 1999
User Commands
3.4.19 rt — Return to Calling Program (Exit Mini-Debugger)
The return (rt) command exits the mini-debugger.
Control Flags
Not applicable.
Description
The return command exits the mini-debugger, returning to the calling program if there
is one. For the standalone mini-debugger, it simply exits.
Returning from a mini-debugger built into the SROMs provided with the motherboards
allows you to continue with the booting process, as if the mini-debugger had not been
invoked.
The rt command is also useful during debugging of SROM code you may write. You
can place calls to the mini-debugger throughout the SROM code to act as breakpoints.
You can then examine the system and CPU state at those points and return to the SROM
code to continue its execution.
Example
An example of the rt command follows:
SROM&gt; rt
9 April 1999
SROM Mini-Debugger Command Set
3–29
User Commands
3.4.20 sb — Set Base Address
The set base (sb) address command defines the base address to be added to user-specified addresses when the base address flag is enabled.
Control Flags
Not applicable.
Description
Using a base address is convenient when examining or depositing of the same address
frame is needed (particularly when the high-order bits of the address must be set). The
base address entered with the set base command is added to the addresses entered in
any subsequent examine or deposit commands, saving the user some typing. This
command always enables the base flag.
Example
To access a flash ROM part that responds to addresses 3.FFF80000 through
3.FFFFFFFF, it may be more convenient to enter its base address and work with offsets,
rather than typing the absolute address every time.
SROM&gt; sb
A&gt; 3fff80000
00000003.fff80000
BaseAddr ON
SROM&gt; bm
A&gt; 0
A&gt; 10
00000003.fff80000:
00000003.fff80004:
00000003.fff80008:
00000003.fff8000c:
5a5ac3c3
a5a53c3c
00000038
00006579
SROM&gt; ba
00000003.fff80000
BaseAddr OFF
SROM&gt; em
A&gt; 400000
00000000.00400000: 00400000
SROM&gt; ba
00000003.fff80000
BaseAddr ON
SROM&gt; bm
A&gt; 30
A&gt; 40
3–30
SROM Mini-Debugger Command Set
9 April 1999
User Commands
00000003.fff80030:
00000003.fff80034:
00000003.fff80038:
00000003.fff8003c:
9 April 1999
00000001
0000be8a
47ff041f
47ff041f
SROM Mini-Debugger Command Set
3–31
User Commands
3.4.21 st — Start Image Execution
The start image (st) command begins execution at a specified address.
Control Flags
Not applicable.
Description
The start image command transfers control to the code residing at the specified address.
If the address does not contain executable code, then the machine hangs. You must
recycle the power to start again.
Note:
The Alpha Microprocessors SROM Mini-Debugger is stored in the
instruction cache (Icache). An st command causes the Icache to be
overwritten and eliminates your ability to return to the mini-debugger.
Example
The st command begins execution of the uploaded image.
SROM&gt; xm
A&gt; 400000
D&gt; 10
SROM&gt; st
A&gt; 400000
3–32
! Address to start execution at.
SROM Mini-Debugger Command Set
9 April 1999
User Commands
3.4.22 wa — Set Write Address Flag
The write address (wa) command enables or disables the write address flag.
Control Flags
!d (negate data flag)
Description
When the write address flag is enabled, write operations use the destination address as
their data. This allows for unique values to be written to individual locations (a useful
feature when debugging the memory subsystem). If the negate data flag is enabled, the
one’s complement of the address being written is used instead. Commands that request
data to be written will not do so if this flag is enabled.
The default state is off; data used by deposit commands is provided by the user.
Example
In the following example, after enabling the write address flag, the region between
400000 and 400020 is filled with its own address in 32-bit increments. With qw mode
on, deposits are performed in quadword increments, and the data written changes in
64-bit increments.
SROM&gt; wa
Wrt Addr ON
SROM&gt; fm
A&gt; 400000
A&gt; 400020
SROM&gt; bm
A&gt; 400000
A&gt; 400020
00000000.00400000:
00000000.00400004:
00000000.00400008:
00000000.0040000c:
00000000.00400010:
00000000.00400014:
00000000.00400018:
00000000.0040001c:
00400000
00400004
00400008
0040000c
00400010
00400014
00400018
0040001c
SROM&gt; qw
QW ON
SROM&gt; fm
A&gt; 800000
A&gt; 800030
9 April 1999
SROM Mini-Debugger Command Set
3–33
User Commands
SROM&gt; bm
A&gt; 800000
A&gt; 800030
00000000.00800000:
00000000.00800008:
00000000.00800010:
00000000.00800018:
00000000.00800020:
00000000.00800000
00000000.00800008
00000000.00800010
00000000.00800018
00000000.00800020
With the negate data flag enabled, the complement of the address is used instead.
SROM&gt; qw
QW OFF
SROM&gt; !d
Neg Data ON
SROM&gt; fm
A&gt; 500000
A&gt; 500020
SROM&gt; bm
A&gt; 500000
A&gt; 500020
00000000.00500000:
00000000.00500004:
00000000.00500008:
00000000.0050000c:
00000000.00500010:
00000000.00500014:
00000000.00500018:
00000000.0050001c:
3–34
ffafffff
ffaffffb
ffaffff7
ffaffff3
ffafffef
ffafffeb
ffafffe7
ffafffe3
SROM Mini-Debugger Command Set
9 April 1999
User Commands
3.4.23 xb — External Boot
The external boot (xb) command begins execution of the uploaded image.
Control Flags
Not applicable.
Description
The external boot command is used after an image has been uploaded with the xm command. It adds the necessary Icache flush code before it transfers control to the code
residing at the address specified in the xm command. If no xm command has been executed, then this command has no effect.
Example
The following example begins execution of the uploaded image:
SROM&gt; xm
A&gt; 400000
D&gt; 10
SROM&gt; xb
9 April 1999
!
Execution of code at 400000 begins.
SROM Mini-Debugger Command Set
3–35
User Commands
3.4.24 xm — External Image to Memory
The external image to memory (xm) command loads an image into memory.
Control Flags
Not applicable.
Description
The external image to memory command loads an external image into memory. The
first input is the destination address, followed by the number of bytes to load. The
number of bytes should be a multiple of 8 and the starting address should be quadword
aligned. Normally, this command is used by an external utility called uload.exe (for
Tru64 UNIX) or xload.exe (for Windows NT).
Examples
This section contains three examples:
•
Uploading an image with the xm command
•
Downloading the Debug Monitor with the Tru64 UNIX uload utility
•
Downloading the Debug Monitor with the Windows NT xload utility
Upload an Image with xm
You can upload an image by typing the starting address and the number of bytes to
upload. In this example, 16 bytes are copied from the SROM port to address 400000.
SROM&gt; xm
A&gt; 400000
D&gt; 10
Download the Debug Monitor with Tru64 UNIX uload
The following example shows how you can use the uload (Tru64 UNIX) utility, which
in turn uses the xm command to download the Debug Monitor. You can follow this
example if the flash has been erased accidentally.
!
!
!
!
!
AlphaPC 264DP Log.
If our flash has been erased and we want to reload
and run the Debug Monitor, this session will load the
code through the Debug Monitor and run it.
tip tty00 -115200
connected (Enter)
21264...V00002501
SROM&gt; ~.
[EOT]
3–36
SROM Mini-Debugger Command Set
!Connect to serial port tty00
!and set baud rate.
!Disconnect from tip session.
9 April 1999
User Commands
uload dp264dbm.cmp 300000 /dev/tty00 115200
!Load Debug Monitor at address
!300000, using serial port tty00, at
!baud rate 115200.
**** ULOAD V2.0 [DEC 17 1997] ****
**** SROM Binary Load Utility ****
Retrieving image to upload: dp264dbm.cmp
Size of file 0x31300 (201472) bytes
Connecting to seral port: /dev/tty/00
Syncing with remote terminal...
U
Error:
!Error condition exists only
!until correct baud rate is found.
SROM&gt;
Sending XM command.
!Uload sends XM command.
Destination = 0x300000, Size = 0x31300 (201472) bytes
Bytes
0
Time
00:00
SROM&gt;
tip tty00 -115200
connected (Enter)
SROM&gt; st
A&gt; 300000
!Uload finishes and exits.
!Tip back to mini-debugger.
!Starts Debug Monitor image execution at
!address 300000 and overwrites Icache.
Download the Debug Monitor with Windows NT xload
The following example shows how you can reload and run the Debug Monitor through
the SROM Mini-Debugger Binary Load utility. You can follow this example if the flash
has been erased accidentally.
!
!
!
!
!
!
!
!
!
!
!
!
!
9 April 1999
AlphaPC 264DP Log.
If our flash has been erased and we want to reload
and run the Debug Monitor, this session will load the
code through the Debug Monitor and run it. Perform the following steps:
1. If you wish, you can open a hyperterminal to verify the
connection. To do this, open the hyperterminal on a Windows NT
system, with the baud rate set to 19200, and flow control
set to none. You are now ready to start your SROM mini-debugger
session.
SROM Mini-Debugger Command Set
3–37
User Commands
! 2. Power on your system, which displays the following:
DP264...V00005201.01.000000041ac60030.02.000007d1.03.0373bef8c1.05.04..
0608000000.14.17
!Stops here until you press enter.
(Enter)
21264...V00002501
SROM&gt;
! 3. Stop the hyperterminal session by closing the window on the Windows
!
NT system. Open a command prompt window and go to the
!
directory where the file dp264dbm.cmp is located.
C:\&gt;cd ebsdk\ebfw\boot\dp264
C:\ebsdk\ebfw\boot\DP264&gt;
! 4. Before trying to XLOAD, ensure that xload.exe is in your path.
C:\ebsdk\ebfw\boot\DP264&gt;xload dp264dbm.cmp 300000 com1 fast
*** Flamingo/Sandpiper/Pelican/Morgan SROM XLOAD Utility V2.1 ***
%XLOAD-I-CMDLIN SROM&gt; XM...
%XLOAD-I-PAGSNT, X loaded page 315
C:\ebsdk\ebfw\boot\DP264&gt;
! 5. After XLOAD completes, reconnect the hyperterminal connection and
!
press the ENTER key to establish communication with the
!
SROM mini-debugger. Then type the following command:
SROM&gt;xb
!
!
This runs the Debug Monitor on your AlphaPC 264DP, through which
you can flash a new Debug Monitor or AlphaBIOS.
! 6. After the image is flashed into the system, replace your SROM
!
mini-debugger with the production SROM.
3–38
SROM Mini-Debugger Command Set
9 April 1999
A
Support
A.1 Customer Support
The Alpha OEM website provides the following information for customer support.
URL
Description
http://www.digital.com/alphaoem Contains the following links:
•
•
Developers’ Area: Development tools, code examples,
driver developers’ information, and technical white
papers
Motherboard Products: Motherboard details and
performance information
•
Microprocessor Products: Microprocessor details and
performance information
•
•
•
News: Press releases
Technical Information: Motherboard firmware and
drivers, hardware compatibility lists, and product
documentation library
Customer Support: Feedback form
A.2 Alpha Documentation
The following table lists some of the available Alpha documentation. You can
download Alpha documentation from the Alpha OEM World Wide Web Internet site:
http://www.digital.com/alphaoem
Click on Technical Information.
Then click on Documentation Library.
9 April 1999
Title
Order Number
Alpha Architecture Reference Manual1
EY–W938E–DP
Alpha Architecture Handbook
EC–QD2KC–TE
Alpha 21164 Microprocessor Hardware Reference Manual
EC–QP99C–TE
Alpha 21164 Microprocessor Data Sheet
EC–QP98C–TE
Support
A–1
Title
Order Number
21164PC Alpha Microprocessor Hardware Reference Manual
EC–R2W0A–TE
AlphaPC 264DP Product Brief
EC–RBD0A–TE
AlphaPC 264DP User’s Manual
EC–RB0BA–TE
AlphaPC 264DP Technical Reference Manual
EC–RB0DA–TE
AlphaPC 164SX Motherboard Product Brief
EC–R57CA–TE
AlphaPC 164SX Motherboard Windows NT User’s Manual
EC–R57DB–TE
AlphaPC 164SX Motherboard DIGITAL UNIX User’s Manual
EC–R8P7B–TE
AlphaPC 164SX Motherboard Technical Reference Manual
EC–R57EB–TE
AlphaPC 164LX Motherboard Product Brief
EC–R2RZA–TE
AlphaPC 164LX Motherboard Windows NT User’s Manual
EC–R2ZQF–TE
AlphaPC 164LX Motherboard Tru64 UNIX User’s Manual
EC–R2ZPC–TE
AlphaPC 164LX Motherboard Technical Reference Manual
EC–R46WC–TE
Alpha Motherboards Software Developer’s Kit Product Brief
EC–QXQKD–TE
Alpha Motherboards Software Developer’s Kit Read Me First
EC–QERSJ–TE
Alpha Microprocessors Motherboard Debug Monitor User’s Guide
EC–QHUVG–TE
Alpha Microprocessors Motherboard Software Design Tools User’s
Guide
EC–QHUWE–TE
1
A–2
Support
Not available on website. To purchase the Alpha Architecture Reference Manual, contact your local
sales office or call Butterworth-Heinemann (DIGITAL Press) at 1–800–366–2665.
9 April 1999
Index
B
block memory command, 3–7
Connecting
to a dumb terminal, 2–2
to a PC, 2–2
to a serial port, 2–4
to a system for Tru64 UNIX, 2–3
to a system for Windows NT 4.0, 2–2
Conventions of document, viii
bm
copy command, 3–9
See block memory command
boot, 2–4
cp
C
D
cm
d
See compare command
Command features, 3–1
dc
ba
See set base address flag command
Baud rate, 2–4
Command summary, 3–2
Commands, 3–1
block memory, 3–7
compare, 3–8
copy, 3–9
deposit CPU register, 3–10
deposit memory, 3–13
display, 3–12
examine CPU registers, 3–14
examine memory, 3–16
external boot, 3–35
external image to memory, 3–36, 3–38
fill memory, 3–18
flags, 3–17
follow-with-read, 3–20
follow-with-write, 3–23
loop, 3–25
memory test, 3–26
negate data, 3–4
print register, 3–27
quadword, 3–28
return, 3–29
set base, 3–30
set base address flag, 3–6
start image, 3–32
write address, 3–33
compare command, 3–8
See copy command
See negate data command
See deposit CPU register command
Debug Monitor
reloading with uload, 3–36
reloading with xload, 3–37
Debugging memory faults, 2–4
Default conditions, 2–4
deposit CPU register command, 3–10
deposit memory command, 3–13
di
See display command
display command, 3–12
dm
See deposit memory command
Document
conventions, viii
purpose, vii
Documentation
ordering, A–1
Dumb terminal, 2–2
E
ec
See examine CPU registers command
9 April 1999
Index–1
See examine memory command
examine CPU registers command, 3–14
MCHK
See machine check handler
memory test command, 3–26
examine memory command, 3–16
mt
em
See memory test command
external boot command, 3–35
external image to memory command, 3–36
through uload utility, 3–36
through xload utility, 3–38
F
N
negate data command, 3–4
P
Features, 1–1
command language, 3–1
hardware debug, 2–1
fill memory command, 3–18
fl
PC, connecting to, 2–2
pr
See print register command
print register command, 3–27
See flags command
flags command, 3–17
Purpose of document, vii
Flash memory
recovery from erasure with uload, 3–36
recovery from erasure with xload, 3–37
fm
See fill memory command
follow-with-read command, 3–20
Q
quadword command, 3–28
qw
See quadword command
follow-with-write command, 3–23
R
fr
Required hardware, 2–1
See follow-with-read command
fw
See follow-with-write command
G
return command, 3–29
rt
See return command
Running the mini-debugger, 2–4
Getting started, 2–1
S
H
sb
Hardware debug features, 2–1
Hardware requirements, 2–1
I
Introduction, 1–1
L
lo
See loop command
loop command, 3–25
M
Machine check handler, 2–4
Index–2
See set base command
Serial port
connecting to, 2–4
Serial port setup, 2–2
set base address flag command, 3–6
set base command, 3–30
SROM serial port, 2–2
st
See start image command
start image command, 3–32
Starting the mini-debugger, 2–4
Synchronization, 2–4
T
Table of commands, 3–2
9 April 1999
Terminal, connecting to, 2–2
tip
Tru64 UNIX command, 2–4
Tru64 UNIX
connecting to a system, 2–3
tip command, 2–4
U
uload utility
downloading Debug Monitor, 3–36
UNIX
See Tru64 UNIX
User commands, 3–3
User interface features, 3–1
W
wa
See write address command
Windows NT 4.0 system, connecting to, 2–2
write address command, 3–33
X
xb
See external boot command
xload utility
downloading Debug Monitor, 3–37
xm
See external image to memory command
9 April 1999
Index–3
">
Ahoj! Som AI chatbot, ktorý je špeciálne vyškolený na pomoc s Compaq SROM Mini-Debugger. Dôkladne som preskúmal dokument a môžem vám pomôcť nájsť presné informácie, ktoré potrebujete, alebo vysvetliť obsah jasne a jednoducho. Či už hľadáte rady o konkrétnych funkciách, kroky na riešenie problémov alebo všeobecné použitie, neváhajte a položte svoje otázky. Čím viac podrobností poskytnete o svojich obavách alebo potrebách, tým presnejšie a efektívnejšie vám môžem pomôcť!
Asistent píše
Asistent nie je pri klávesnici. Skúste to znova neskôr.
Zdá sa, že ste sa dostali k dokumentu, ktorý je napísaný vo viacerých jazykoch, vrátane jazyka, ktorý nie je váš rodný jazyk. Pomocou nasledujúcich odkazov môžete dočasne skryť stránky bez preferovaného jazyka.