USB Turntable Installation & User's Guide 62904201 Item number

USB Turntable Installation & User's Guide 62904201 Item number
USB Turntable
Item number 62904201
R
R
Installation & User's Guide
All brand names and trademarks are the property of their respective owners.
1
Precautions
Before Use
Safety Information
CAUTION
1.In order to shut off the power of this product completely, unplug the power cord from the
wall outlet. Be sure to unplug the unit if you do not intend to use it for an extended period
of time.
2.If this product develops trouble, contact our service center, and do not use the product in
defective state.
Safety Precautions
WARNING:
To reduce the risk of fire or electric shock, do not expose this appliance to rain or moisture.
CAUTION
RISK OF ELECTRIC SHOCK DOES NOT OPEN
To reduce the risk of electric shock: do not remove cover(or back).
No user serviceable parts inside. Refer servicing to qualified service personnel.
1. Choose unit installation location carefully. Avoid placing it in direct sunlight or close to a
source of heat. Also avoid locations subject to vibrations and excessive dust, cold or
moisture. Keep away from sources that hum, such as transformers or motors.
2. Do not open the cabinet as this might result in damage to the circuitry or electrical shock,
if a foreign object should get into the set, contact your dealer.
3. Be sure not to handle records with dirty fingers. Never play a record that has a crack on
the surface.
4. When removing the adapter from the wall outlet, always pull directly on the adapter, never
pull the cord.
5. Do not attempt to clean the unit with chemical solvents as this might damage the finish.
Use a clean, dry cloth.
6. In order to shut off the power to this product completely, unplug the adapter from the wall
outlet. Be sure to unplug the unit if you do not intend to use it for an extended period of
time.
7. Keep this manual in a safe place for future reference.
Beware of Condensation
When the turntable is moved from a cold to a warm place or is used after a sudden
temperature change, there is a danger of condensation. Water vapor in the air could
condense on the mechanism. To prevent this, if you are going to use the turntable in a
condition where condensation could occur, you should leave the turntable on for 1 or 2
hours after plugging it into an AC outlet depending on the amount of condensation. If this is
done, the turntable will stabilize at the temperature of its surroundings.
The lightning flash with arrowhead symbol, within an equilateral triangle, is
intended to alert user to the presence of uninsulated "dangerous voltage"
within the product's enclosure that may be of sufficient magnitude to
constitute risk of electric shock to persons.
The exclamation point within an equilateral triangle is intended to alert user
to the presence of important operating and
maintenance(servicing)instructions in the literature accompanying the
appliance.
2
3
Location of parts
Preparation for Use
1. Remove all the packaging from the unit.
2. Connect the AC adaptor to the turntable and then to
an AC outlet.
1.POWER SWITCH
2.TONE ARM
3.SPEED CONTROL SWITCH
4.SECURITY HOOK
5.TONE ARM REST
6.TURNTABLE
7.SUSPENSION SCREW
8. PLAY BUTTON
9.EJECT BUTTON
10.STOP BUTTON
11.USB JACK
12.LINE OUT
13.DC JACK
Front View
1
7
3. The suspension screw protects the phonograph chassis during transportation. Turn this
screw clockwise to release the turntable suspension system. This will alow the
turntable to absorb any vibrations while playing.
2
4
5
3
8
6
10
9
12
How To Replace The Stylus
Removing old stylus
1. Set a screwdriver at the tip of the stylus and push down to
the direction "A".
2. Remove the stylus by pulling it down and forward.
LINE OUT
USB OUT
11
Back View
A
13
Installing a new stylus
1. Hold the tip of the stylus and insert the other edge by
pressing in the direction "B".
2. Push up in the direction "C" until it locks at the tip.
C
B
Guide Pins (inside)
4
5
Listening to a Record
Audacity Music Software and USB Computer Connection
1. Connect the AC adapter to the main
power supply, the standard is 120V60Hz, and output
DC 9V.
Line Out
2. Plug the other ends of the RCA Cable
into the auxiliary input (Aux) on your TV,
home entertainment receiver or other
music system, be sure that the red RCA
Cable is inserted into the red jack and
the white RCA Cable is inserted into the
white jack.(optional)
LINE OUT
USB OUT
2. Using the attribute control button at the
top of the screen, go to beginning, Play,
Record, Pause, Stop and go to end. Use
the File, Edit, View, Project, Generate,
Effect and Analyze menus to Save, Export,
and edit the music.
Installing the Audacity Software
Install the Audacity software in your
Computer, the disc is compatible with the
USB turntable.
USB Jack
Back View
3. Switch on the unit using the POWER
switch on the front.
2
1
Insert the Audacity disc into the CD
drive of your computer.
Click on My Computer on the desktop.
Double click CD drive to view the
contents of the Audacity disc.
Double click Audacity Set Up to install
the Audacity software according to the
instructions.
Footnote:If you misplace your software
CD or it becomes damaged,you may
download Audacity software online at:
http://download-audacity.org/
4. Put a record onto the turntable, when
playing the 45rpm record, remember to
use the adapter.
5. Select correct speed according to the
record you are playing.
Front View
6. Remove the tone arm from the holder, lift
the que-lever and move the tone arm
gently to the desired position over the
record, lower the que-lever slowly, then
the record will begin playing.
3
3. Select preferences at the bottom of the
menu which will open up Audacity
Preferences. You can set the Audio
I/O,Quality,File Formats, Spectrograms,
Directories, Interface, Keyboard and
Mouse in the Audacity preference
Interface.
Stereo
Install the USB Driver
7. Turn on the receiver which you
connected to this USB turntable by
using the On/off Knob or Volume knob,
adjust the volume knob to control the
volume of the music.
4
6
8. Press STOP button to stop playing.
5
Make sure the Audacity disc is still in
your CD drive.
Using the included USB cable, connect
the turntable to your computer.
Follow screen instructions to install the
USB driver.
Running the Software
9. Press the PLAY button to continue
playing.
Audacity Preferences
1.Double click the Audacity software icon
“
” and it will open the following
interface;
10. When the music is finished playing, and
the tone-arm reaches the end of the
record, the tone-arm will return to the
arm-rest automatically. Or you can
press the eject button when playing the
record, the tone arm will lift from the
record and then back to the arm-rest.
Sound Mapping
8
9
Sound Mapping
Stereo
10
6
7
Audacity Music Software and USB Computer Connection
4. Adjust the output and input volume.
Output Volume
2
Sound Recorder Interface
Audacity Music Software and USB Computer Connection
3
Audio Properties Interface
Input Volume
Stereo
6.Click the (
) button to skip to start;
7.Click the (
) button to skip to end;
8.Click the (
) button to play;
9.Click the (
record play;
) button to pause the
Stereo
Line in Volume
Microphone Volume
5.Select the record button ( ) to record
the disc, the left and right tracks will show
on the interface;
10.Click the (
Recording.
6
) button to stop the
8
5
9
10
7
3 Select Edit and click “Audio Properties”
in the bottom of the menu to open
“Audio Properties” interface;
Stereo
11.Export the Music Files for WAV,MP3,
Ogg Format.
Once you have finished the recording,
you should save your music to the
computer.
Click File menu and move down to
Export as WAV format,MP3 format or
Ogg format.
Click one format to save the music,
and you will be asked for the file name
of the music recorded.
Note: Audacity does not export MP3
files directly, you should download the
LAME MP3 encoder, which is named
lame_enc.dll.
4 Select sound recording volume and
come into“Recording Control” interface;
If you do not have the fluctuant wave on the
interface when recording, please adjust
the line in volume as follows:
1 Click “start” in the left corner of the
computer,Select“Programs”,
“Accessories”,“Entertainment”, “Sound
Recorder” and it will open the sound record
interface.
Control
Adjust the line in volume to the upper or
middle, of the scale,the fluctuant wave
should now show on the interface when
recording.
Rising Security
8
9
Specifications
TURNTABLE SECTION
Motor..............................................DC servo motor
Drive System...................................Belt Drive
Speeds...........................................33-1/3 rpm, 45 rpm and 78 rpm
Wow&Flutter....................................Less than 0.25%(WTD)
S/N Ratio.........................................More than 50 dB
Cartridge Type.................................Ceramic Stereo Cartridge
Stylus..............................................402-M208-165
Output Level....................................160-380 mV (5 cm/sec at 1 KHz)
GENERAL
Power Requirements........................Input: AC 120 V~ 60 Hz Output: DC 9V~ 800 mA
Power Consumption.........................5 W
Standard Accessories.......................Operating Instruction Booklet
45 rpm Adapter
Troubleshooting Guide
In case of trouble with the unit ,please look through this chart and see if you can solve the problem
by yourself before calling our tech support 800 639 3803 Line.
TURNTABLE
Problem
cause
solution
Power does not come on
when the power switch is
pressed.
Unit is unplugged.
Connect the unit to the AC
power supply.
The sound is noisy.
The unit is too close to a
TV set or another similar
appliance.
Turn off the TV or other
appliance, and relocate the
unit.
10
11
12
13
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement