R.H. Peterson | G4-24A-SS | Owner`s manual | R.H. Peterson G4-24A-SS Owner`s manual

R.H. Peterson G4-24A-SS Owner`s manual
Owner’s
Manual
Models:
For use with
natural gas
only
G4-18/20-SS
G4-24-SS
G4-30-SS
G4-Stainless Steel Burner For Outdoor Use Only
Important:
Read this manual carefully before starting installation of the log set.
CODE AND SUPPLY REQUIREMENTS
This outdoor burner must be installed in accordance
with local codes and ordinances, or in the absence of
local codes, with the latest National Fuel Gas Code,
ANSI Z223.1.
WARNING
If the information in this manual is not
followed exactly, a fire or explosion
may result, causing property damage,
personal injury, or loss of life.
WARNING
Improper installation, adjustment, alteration,
service, or maintenance can cause injury or
property damage. Refer to this manual. For
assistance or additional information consult a
qualified professional installer, service agency,
or gas supplier.
- Do not store or use gasoline or other
flammable vapors and liquids in the
vicinity of this or any other appliance.
WHAT TO DO IF YOU SMELL GAS:
• Open a window.
• Do not try to light any appliance.
• Do not touch any electrical switch; do not use
any phone in the building.
• Immediately call the gas supplier from a
neighbor’s phone. Follow the gas supplier’s
instructions.
• If you cannot reach the gas supplier, call the
fire department.
- Installation and service must be performed
by a qualified installer, service agency, or the
gas supplier.
This appliance is designed as an attended
appliance. Adults must be present when the
unit is operating. DO NOT leave this unit burning
when unattended. If this product is left burning
unattended it may cause damage or serious
injury.
INSTALLER: Leave these instructions with consumer.
CONSUMER: Retain for future reference.
ROBERT H. PETERSON CO. • 14724 East Proctor Avenue • City of Industry, CA 91746
REV 7 - 0903130830
1
No. L-A2-17509
TABLE OF CONTENTS
SAFETY INFORMATION
PARTS LIST
BEFORE YOU BEGIN - IMPORTANT INFORMATION
INSTALLING THE DAMPER CLAMP
INSTALLATION
LOG PLACEMENT
CHARRED SERIES SUPPLEMENTAL INSTRUCTIONS
OPERATING THE LOG SET - LIGHTING AND EXTINGUISHING
NOTES PAGE
TECHNICAL DATA AND SPECIFICATION INFORMATION
TROUBLESHOOTING THE GAS LOG SET
WARRANTY
2
3
4
5
5
7
8
9
10
11
12
14
SAFETY INFORMATION
1. Children and adults should be alerted to the hazards of high surface temperatures and
should stay away to avoid burns or clothing ignition.
2. Young children should be carefully supervised when they are in the area of the
appliance.
3. Clothing or other flammable materials should not be placed on or near the appliance.
4. Any guard or other protective device removed for servicing the appliance must be
replaced prior to operating the appliance.
5. Installation and repair must be done by a qualified service person. The appliance must be
inspected before use and at least annually by a qualified service person. More frequent
cleaning may be required as necessary.
6. Solid fuels shall not be burned in a fireplace where this gas log set is installed.
7. Keep the appliance area clear and free from combustible materials, gasoline and other
flammable vapors and liquids.
8. The burner assembly must be replaced prior to the appliance being put into operation
if it is evident that the burner assembly is damaged. Contact your local dealer for
replacement parts.
REV 7 -0903130830
2
No. L-A2-17509
PARTS LIST
Before beginning installation, be sure the gas log set is complete by comparing its contents with this PARTS
LIST. The RG4-24 set is listed and illustrated. The parts may differ depending upon the log style and size
of the set. Be sure you know the model number and size of your set when ordering replacement or optional
parts and accessories.
9
6
4
Large adapter
9a
Replacement parts can be
ordered from your local
dealer.
10
Glowing embers
5
3
2
11
Lava granules
Stainless steel
flex tube
9b
1
7
12
Small adapter
9c
8
ITEM# DESCRIPTION
1.
Golden Oak front bottom log 24"
ITEM# DESCRIPTION
8.
Burner pan assembly
2.
Golden Oak Rear bottom log 20"
9.
Connector kit
3.
Golden Oak top log 15"
10.
Real-Fyre® glowing embers
4.
Golden Oak top log 15"
11.
Lava granules
5.
Golden Oak top log 9"
12.
Damper clamp
6.
Golden Oak top log 9"
13.
(2) Stabilizer clips
7.
Fireplace grate 24"
REV 7 - 0903130830
3
13
No. L-A2-17509
BEFORE YOU BEGIN - IMPORTANT INFORMATION
Before You Begin, review the information and
safeguards below about the installation and operation
of the Real-Fyre® gas log set.
Fig. 4-1
Fireplace dimensions
Check to be sure that the fireplace meets the venting
and construction requirements for the installation
of the Real-Fyre® gas log set.
Rear
width
THIS BURNER IS DESIGNED FOR USE WITH
NATURAL GAS. Never use propane gas in this burner.
Height
Depth
Be sure the gas log set is properly sized for the
fireplace. Improper sizing may negatively impact the
proper drafting of the fireplace. Additionally, too large
a log set will adversely affect the burn and hamper the
proper operation of the control system. Too small a log
set will diminish the beauty of the hearth setting. Fig.
4-1 illustrates the critical dimensions of the firebox.
Front
width opening
with all local codes. The gas supply line must have a
½" minimum interior diameter. If the gas line to the
fireplace is longer than 20', a larger diameter line may
be necessary.
This gas log set must be installed by an NFI
Certified or other qualified professional installer.
The installation, including provisions for combustion
and ventilation air, must conform with local codes, or in
the absence of local codes, with the latest edition of the
National Fuel Gas Code, ANSI Z223-1 and NFPA54.
The Real-Fyre® gas log set is to be installed only in
a solid-fuel burning fireplace with a working flue and
constructed of noncombustible material. The fireplace
must have an open damper. The chimney must be free
of any obstructions. The fireplace flue must be at least
8" at its smallest dimension.
Be sure to clean the fireplace floor of any ashes or other
foreign materials. It is recommended that the fireplace
and chimney be examined and cleaned by a chimney
sweep or other qualified person before you install the
Real-Fyre® gas log set, and annually thereafter.
Required Gas Pressure: The minimum inlet gassupply pressure for the purpose of input adjustment
is 5" for natural gas. The maximum inlet gas-supply
pressure for this burner is 10.5" for natural gas.
Testing the Gas Supply System: The gas log set and
its individual shut-off valve must be disconnected from
the gas supply piping system while performing any tests
The fireplace must have a gas supply line that has of the piping system at pressures in excess of ½ psig
been installed by a qualified technician in accordance (3.5 kPa). The gas log set must be isolated from the gas
Min. Fireplace Dimensions
supply piping system by closing its individual manual
BTU
Burner
shut-off valve during any pressure testing of the gas
Width
Depth
Height
size
supply piping system at test pressures equal to or less
Front Rear*
NAT.
than ½ psig (3.5 kPa). This is accomplished by closing
18/20"
24"
20"
12"
18"
75M
the gas supply line valve, which is required by NFPA
24"
28"
26"
12"
18"
95M
54, section 5.54. A fireplace screen must be in place
30"
36"
32"
12"
18"
98M
when the log set is burning and, unless other provisions
for combustion air are provided, the
MINIMUM FREE OPENING AREA OF CHIMNEY DAMPER FOR VENTING
screen must have an opening(s) for
For Factory Built Fireplaces
For Masonry Built Fireplaces
introduction of combustion air. When
Log Set Sizes
Log Set Sizes
a glass fireplace enclosure (door) is
Chimney
18/20"
24"
30"
18/20"
24"
30"
used, operate the gas log set with the
Height
glass doors open.
15'
47 sq. in.
60 sq. in.
62 sq. in.
51 sq. in.
64 sq. in.
66 sq. in.
20'
43 sq. in.
54 sq. in.
56 sq. in.
47 sq. in.
58 sq. in.
60 sq. in.
25'
41 sq. in.
51 sq. in.
53 sq. in.
45 sq. in.
55 sq. in.
57 sq. in.
30'
38 sq. in.
48 sq. in.
50 sq. in.
42 sq. in.
52 sq. in.
54 sq. in.
Important:
REV 7 - 0903130830
* Note: Rear width is at corresponding
depth.
For safe operation and proper performance of this product and to comply with certification, listings,
and building code acceptances, use ONLY Peterson Real-Fyre® controls, parts, and accessories
that have been specifically listed or certified for use with this burner system. Use of other controls,
parts, or accessories is prohibited and will void all warranties, certifications, listings, and building
code approvals, and may cause property damage, personal injury, and loss of life.
4
No. L-A2-17509
INSTALLING THE DAMPER CLAMP
A damper clamp is provided as a means to prevent full 4. Should the damper clamp not fit, install a permanent
damper stop or provide some other means of
and/or accidental closure of the fireplace damper when
installed as illustrated (Fig. 5-2). When the gas log
preventing full and/or accidental closure of the
damper.
set is operating, the damper must be fully open. To
install the damper clamp:
1. Open the fireplace damper.
2. Place the damper clamp over the damper blade (Fig.
5-2).
3. Tighten the set screw of the damper clamp with
pliers or a wrench so that it affixes to the damper
blade. The clamp must be permanently installed.
Fig. 5-1
Set screw
Open
Fig. 5-2
Damper clamp
Closed
INSTALLATION
Refer to the PARTS LIST when installing the RealFyre® gas log set
Fig. 5-3
WARNING: Failure to position the parts in accordance
with these diagrams or failure to use
only parts specifically approved with this
appliance may result in property damage
or personal injury.
Gas line
cap
1. Carefully unpack the burner system. Check the
PARTS LIST to be sure all parts are included.
Gas supply
2. Check to be sure that the Real-Fyre® gas log set
line stub
is designed for the type of gas that fuels the
fireplace.
Install the stabilizer clips on the grate bars so that the
3. Be sure the gas supply to the fireplace is turned off. slots of the stabilizer clips fit over the back edge of the
burner pan. Use the nuts and bolts provided to secure
4. Clean the fireplace floor of any dirt or ashes.
the clips in position.
5. Remove the cap from the gas supply line stub in
Remove grate for gas connection and granule/ember
the fireplace (Fig. 5-3).
placement.
Caution:
Be sure that when removing the cap,
the stub does not turn, loosening the
Fig. 5-4
Back
connection inside the wall.
wall of
PLACEMENT OF GRATE AND BURNER
Grate
Stabilizer
clips
fireplace
The Real-Fyre® grate is modeled after wood-fire grates
to add to the natural wood-fire appearance of the log
set. Its heavy duty construction and design provides a
better fit - even in narrow, shallow fireboxes - and works
with the log set to provide an attractive flame pattern.
To position the Real-Fyre® gas log set properly in the
fireplace, place the grate as far back in the fireplace
as possible, centered left-to-right (Fig. 5-4). The grate
is tapered. The widest side should face forward.
REV 7 - 0903130830
BURNER PAN
5
No. L-A2-17509
INSTALLATION (cont.)
CONNECTING THE GAS SUPPLY
GRANULE PLACEMENT
1. The burner pan is supplied with a fuel injector
for natural gas. The fuel injector must be used
in ALL installations. The fuel injector has a
precisely sized orifice to ensure only the proper
quantity of gas enters the burner. This allows
maximum performance and gas conservation.
The granules supplied with the unit are specially
selected for use with natural gas. They maximize
flame distribution and reduce carbon buildup.
1. With the burner pan off and properly positioned
in the fireplace, fill the burner pan completely
with the granules. Avoid spilling the granules
on the Peterson control, if one is in place.
2. When installing the log set, use Teflon tape or
pipe compound resistant to the action of
gas on all threaded male connections except
brass to brass connections.
2. Slope the granules at the same angle as the
burner pan. This is important to ensure quiet
lighting and even flame distribution.
3. Installing the gas log set (see Fig. 6-1)
3. Pour a small amount of the granules along the
outside bottom edges and back of the burner
pan (Fig. 6-2). This prevents flame diversion.
a. Attach the large adapter (Item 9a) to the gas
supply stub in the fireplace. Use Teflon tape or
pipe compound on the stub. Tighten securely.
Connect the tubing to the adapter.
Fig. 6-2
b. Attach the smaller adapter (Item 9c) to the fuel
injector on the burner pan using Teflon tape
or pipe compound and tighten securely.
Back
wall of
fireplace
c. Connect the open end of the flex tubing to the
small adapter. Tighten securely.
Burner pan
d. Use a long-necked butane lighter, or lay a
lighted match next to the burner pipe, and
carefully turn on the gas supply until the
burner ignites.
Granules
e. Test for leaks at all connections with a soapy
water solution. Never use an open flame to
check for leaks.
e. Turn off gas supply.
GLOWING EMBERS PLACEMENT
f. Proceed to GRANULE PLACEMENT.
Real-Fyre® glowing embers are specially formulated
and sized to create the most authentic, uniform glow,
duplicating red hot coals under the grate. They are a
major element in the beautiful realism of Real-Fyre®
gas log sets. All materials used are nonflammable
and inert, containing no asbestos.
Fig. 6-1 - Fireplace valve
Fuel injector
Aluminum
tubing
1. Sprinkle the Real-Fyre® glowing embers lightly
and evenly over the entire surface of the
granules (Fig. 6-2). For Charred series log sets
see page 9.
BURNER
PAN
Hearth
elbow
GRATE REPLACEMENT
1. Reposition the grate in the fireplace over the
burner pan. Make sure the stabilizer clips slide
over the back edge of the burner pan.
Connector
elbow
Gas
supply line
REV 7 - 0903130830
6
No. L-A2-17509
LOG PLACEMENT
The beauty and design of the Real-Fyre® gas logs
are the result of skilled craftsmanship, research, and
engineering. The fine quality materials used to mold
the logs are formulated from kiln-fired ceramics,
superior refractories and the best expanded shales
and aggregates, exactly proportioned. Added to this
material are steel reinforcing rods, precisely sized and
designed to prevent breakage. This creates realistic,
long-lasting logs. Their durability has been proven by
over a half century of use in family homes. Real-Fyre®
logs are guaranteed for as long as you own them.
Hairline cracks are common and may appear after the
first use. This will not affect the integrity of the logs or
the operation.
Be sure to provide a minimum of 3" between the
front and rear log (Fig. 7-2). This will create the energy
efficiency and heat radiating effect of the log set and
will also reduce carbon buildup.
Fig. 7-2
Front
log
3"
Back wall of
fireplace
Each log is skillfully designed and crafted to duplicate
natural wood. Deep, rugged bark textures and handpainted highlighting challenges the viewer to tell
whether they are looking at real wood logs or RealFyre® logs. Knotholes, branch stubs, and peeled-away
bark in many styles also add to the realism of the
Real-Fyre® gas log set.
DESIGNER AND
PLACEMENT
CLASSIC
SERIES
Rear
log
4. Top logs should be placed diagonally with space
between the logs so that the flames are not
choked off. Top logs may be moved to achieve
the desired flame pattern. Some carbon buildup
(sooting) may be observed where the flames
impinge on the logs. Unless the sooting is
excessive, this should not be a concern. If sooting
is excessive, rearrange the top logs so there is
less flame impingement. Examples of log stacks
are shown in Fig. 7-3.
LOG
(For Charred series log sets see page 9).
1. Log placement is very important for the proper
operation and performance of the Real-Fyre®
gas log set. Although you have some flexibility in
the log arrangement, it is necessary to follow the
log placement instructions carefully to fully enjoy
the log set.
Fig. 7-3
Woodland
Oak
2. The longest log is placed on the front of the grate
with the bark of the log facing forward. If you have
a heat chamber built into the log style, it should
be facing the rear of the fireplace (Fig. 7-1).
3. The second longest log (Item 2) is placed on the
rear of the grate with the bark of the log facing
forward. If you have a heat chamber built into the
log style, it can face forward or to the rear of the
fireplace as you desire.
Split Oak
Designer
Plus
Fig. 7-1
Back wall of
fireplace
Front
log
Royal
English Oak
Designer
Stabilizer
clips
Grate
Burner pan
REV 7 - 0903130830
7
No. L-A2-17509
CHARRED SERIES SUPPLEMENTAL INSTRUCTIONS
These instructions must be used with the Charred series gas log set series
EMBER COALS PLACEMENT
Attach the ember bed to the burner by slipping it
onto the back edge (center left to right) with the
perforated section facing towards the back fireplace
wall.
Fig. 8-1
Ember bed
Part No. CHD-01
Cover the surface of the ember bed with the ember
coals (Fig. 8-1). For best glowing performance,
they should be applied evenly and pulled slightly
apart so the fibers are somewhat loose. (It is not
necessary to pile the entire bag of the ember coals.
More ember coals may be added after completion
of the entire installation.)
Fig. 8-1a
GRATE REPLACEMENT
Note:
Follow the instructions on page 7.
Ember bed(CHD-01) included with Charred Series
log sets only.
CAUTION: Burn hazard. Logs will remain hot for some time after use.
YOU MUST MAINTAIN THE LOG LAYOUT AS SHOWN TO ENSURE PROPER OPERATION OF THE
LOG SET. IF YOU NEED TO REPOSITION ANY LOG TO MAINTAIN THE PROPER LAYOUT, USE HEAT
RESISTANT GLOVES OR ALLOW LOGS ADEQUATE TIME TO COOL BEFORE HANDLING.
CHARRED SERIES SUPPLEMENTAL INSTRUCTIONS
CHARRED SERIES LOG PLACEMENT
Place the long bottom rear log (Log #2) on the back of the grate with the flat hollow side facing the rear of
the fireplace. The two sections of the front log (Logs #1A & 1B) are placed on the front of the grate with the
charred sections facing each other and positioned approximately 1" apart at the top (Fig. 8-2). There
should be 3" between the front and rear logs.
Place the two top knothole logs (Logs #3 & 4) so that one end rests on each front log (Logs #1A & 1B) and
the other end on the rear log (Log #2). The charred sections should be over the opening between the front
and rear logs (Fig. 8-3).
Place the small top charred log (Log #5) between the knothole logs so it rests on the rear log (Log #2) and
the right-hand front log (Log #1B) with the charred section facing the front (Fig. 8-4).
Place the curved top charred log (Log #6) so the charred section rests on the left-hand front log (Log #1A)
and the other end rests on the middle of the right top knothole log (Log #4); see Fig. 8-5.
Place the additional top log (Log #7) on the top in the desired position. Additional log not available with 18"
log set.
* Other options may be chosen for top log placement.
LOG #2
G
#6
LO
#4
#5
Fig. 8-2
G
G
LOG #1A
LO
LO
3"
LO
G
#3
Light the log set, referring to installation instructions for procedures. More ember coals may be placed on
the ember bed for the added realism of a burning-wood look.
G
LO
#7
LOG #1B
Fig. 8-3
Fig. 8-4
Fig. 8-5
Note: Charred Oak (CHD) log set used for illustration.
REV 7 - 0903130830
8
No. L-A2-17509
OPERATING THE LOG SET - LIGHTING AND EXTINGUISHING
FOR YOUR SAFETY, READ BEFORE LIGHTING
WARNING:
If you do not follow these instructions exactly, a fire or explosion may result, causing property
damage, personal injury, or loss of life.
C. Do not use the gas log set if any part has been
underwater. Immediately call a qualified service
technician to inspect the gas log set and to replace
any part of the control system and any gas control
that has been underwater.
A. BEFORE LIGHTING, smell all around the gas
log set area for gas. Be sure to smell next to the
floor because some gas is heavier than air and
will settle on the floor.
B. IF YOU SMELL GAS:
• Shut off the gas to the appliance.
• Extinguish any open flame.
• If odor continues, keep away from the
appliance, and immediately call the gas
supplier or fire department.
LIGHTING THE GAS LOG SET
1. Lay a lighted long-stem match on the surface of the embers near the gas inlet (do not hold the match
in your hand) or use a lighted long-necked butane lighter.
2. Slowly turn the fireplace remote valve to the ON position. The log set should light.
3. If the log set does not light before the match goes out, immediately turn the valve off.
4. Wait approximately five (5) minutes to clear out any gas, and repeat steps 1-3 above. Smell for gas
including near the floor. If you smell gas, stop and follow step B above. If you don’t smell gas, proceed.
5. If the log set fails to light again, turn off the valve and contact the dealer or gas supplier.
TURNING OFF THE GAS LOG SET
1. To extinguish; simply turn the valve to the OFF position. Be sure the valve is turned completely off to avoid
any gas leakage.
REV 7 - 0903130830
9
No. L-A2-17509
NOTES PAGE
REV 7 - 0903130830
10
No. L-A2-17509
TECHNICAL DATA AND SPECIFICATION INFORMATION
MAINTENANCE
SERVICE
Once installed and operating properly, the RealFyre® gas log set requires very little maintenance.
You should inspect the log set and control annually
for the following:
1. Excessive sooting - Some sooting of the log set
is normal and adds to the appearance of burned
wood. If sooting accumulates, you may brush the
soot off with a stiff brush. Do not use water or
soot cleaners to clean off the soot.
While some minor service conditions may
be handled by the owner of the log set, it is
recommended that a qualified service technician be
called to service the gas log set and burner should
service be required. The TROUBLESHOOTING
section of these instructions serves as a guide for
ensuring optimum performance of the gas log set.
FLAME DESCRIPTION
Observe the flames. The main burner flames should
be blue at the base and a combination of blue/
yellow at the body and at the tips. They should be 5"
to 8" above the logs, with the center flame being the
tallest. Flames in the ember burner should be 1/4"
above the embers.
2. Settling of glowing embers and granules Moisture may cause the granules and glowing
embers in the burner pan to settle and affect
the burn. Using a screwdriver or flat blade knife,
carefully stir the granules and embers, loosening
the materials.
3. Debris around the burner - Inspect the burner
pan to be sure it is free of any debris.
To adjust the flame pattern, take a long blade screwdriver or similar tool and stir the granules until the desired
pattern is achieved. DO NOT REMOVE GRANULES FROM THE BURNER PAN
Long bladed screwdriver
(or similar)
Insert blade into granules and
stir in various places until desired
flame pattern is achieved.
REV 7 - 0903130830
11
No. L-A2-17509
TROUBLESHOOTING THE GAS LOG SET
SYMPTOM
1. Excessive smoking
and sooting
CAUSE
A. Poor draft or down draft
Note: Like burning natural
firewood, the RealFyre® gas log set
is designed to
burn with a yellow
smoky flame. Some
sooting is common
and desirable.
C. Damper closed
D. Set is positioned too close
to the front of the firebox
E. Improper log placement
F. Flue is less than 8" in
diameter
2. Low flame
A. Incorrect log set size for
burner system
B. Insufficient gas supply
C. Blockage or kink in
connector kit, plumbing or
burner orifice
D. Valve not fully open
REV 7 - 0903130830
12
SOLUTION
A. Check for chimney blockage.
Be sure chimney is at least
3' taller than anything within
10’ of it in all directions. If
not, consult a chimney sweep.
Chimney cap or fan may help.
Under severe conditions, you
may need to open a window
near the fireplace about 1" to
2" when burning the log set.
C. Open damper fully when
operating gas log set.
D. Move set so that the back of
the grate touches the back wall
of the firebox.
E. Be sure the bottom logs are
spaced at least 3" apart. Top
logs should be placed to
minimize flame impingement.
F. Remove the log set.
Inadequate fireplace
ventilation.
A. Consult the dealer for proper
set.
B. Other gas appliances may
be competing for gas supply.
Consult installer or plumber.
Orifice size is based upon
7" w.c. pressure for natural
gas. Plumbing must supply
adequate pressure.
C. Clean out blockage. If
connector kit is kinked, replace
it.
D. Open valve fully.
No. L-A2-17509
TROUBLESHOOTING THE GAS LOG SET (cont.)
SYMPTOM
3. Uneven flame distribution
(Lower at one end of the
burner)
REV 7 - 0903130830
CAUSE
A. Clogged or blocked
portholes
A.
B. Insufficient gas pressure
and/or supply
C. Granules may be packed
down too tightly or not
evenly
B.
D. Auxiliary shut-off valve
partially closed
D.
13
C.
SOLUTION
Portholes can be cleared of
foreign object by running a
wire through them.
Consult installer or plumber
(see solution 2b).
Loosen granules around
burner pipe by running a
kitchen knife along both
sides of pipe. Even out
granules in burner pan.
Open valve fully. Usually,
you will find this along the
wall 3’ from the fireplace.
No. L-A2-17509
WARRANTY
PETERSON VENTED GAS LOG SETS
LIMITED WARRANTY
All Peterson gas logs are WARRANTED for as long as you own them (lifetime).
All Peterson burner assemblies are WARRANTED for TEN (10) YEARS.
SPK-26 controls are covered by a THREE (3) YEAR “All Parts” Warranty.
All other Peterson valves, pilots, and controls are covered by a ONE (1) YEAR Limited Warranty (excluding batteries).
PLEASE KEEP A COPY OF YOUR SALES SLIP FOR PROOF OF PURCHASE
This warranty applies to the original purchaser and to single family residential use only. It commences from date of purchase, and is valid only with
proof of purchase.
This warranty does not cover parts becoming defective through misuse, accidental damage, electrical damage, improper handling, storage, and/or
installation. Product must be installed (and gas must be connected) as specified in the instructions or operator’s manual, by a qualified professional
installer. Accessories, parts, valves, remotes, etc., when used must be Peterson Co. product.
This warranty does not apply to rust, corrosion, oxidation, or discoloration, unless the affected component becomes inoperable. It does not cover
labor or labor-related charges.
This warranty specifically excludes liability for indirect, incidental, or consequential damages. Some states do not allow the exclusion or limitation of
incidental or consequential damages, so the above exclusion may not apply to you. This warranty gives you specified legal rights, and you may have
other rights that may vary from state to state.
For additional information regarding this warranty, or to place a warranty claim, contact the R.H. Peterson dealer where the product was purchased.
TO REGISTER YOUR PRODUCT ONLINE GO TO: WWW.RHPETERSON.COM,
AND CLICK ON PRODUCT REGISTRATION. THANK YOU FOR YOUR PURCHASE.
Robert H. Peterson Co. • 14724 East Proctor Avenue • City of Industry, CA 91746
14
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising