User manual | DS DALI SQM en

Sequencer module for automatically running a predefined sequence
Type
D
Assembly/installation:
•The DALI SQM must not be connected to the
mains. It is supplied directly via the DALI signal
line.
•The function switch is connected directly to the
DALI SQM (potential free contact) and must not
be connected to the mains.
•DALI signals are not SELV. Therefore the same
procedures should be applied as working with
mains voltage. This is also valid to the function
switch and the cord.
•5-year guarantee
AS
E
Function:
The DALI SQM constantly sends DALI signals with
the set “step time”. These are broadcast-addressed
scene calls. DALI scenes 0 to 15 can be called up.
The end scene, after which scene 0 is called up
again, can be programmed and set to DALI scene
7 on delivery. This means that a sequence of eight
scenes is called up.
O
U
T
DALI SQM
DALI SQM
Article number
86458211
Power supply
from the DALI line
Current input
9 mA
Inputs
rotary switch, 1 s – 30 min.
function switch: max. cable length 100 m
OutputDALI
Permissible ambient temperature
L
N
0 °C – 50 °C
PH
DALI
PS
PCA EXCEL one4all
PCA EXCEL one4all
DALI
DALI
SQM
DALI
USB
Data sheet 08/13-CO057-0 We reserve the right to make technical changes without prior notice.
Glow-wire test
according to EN 60598-1 passed.
DALI standard
The DALI SQM is deisgned to control control gear
with DALI standard IEC 60929 (DALI V0).
Sequencer module for automatically running a predefined sequence
do not connect
Save
DALI SQM
86458211
Reset
Step Times
1s
3s
30 min.
10 s
10 min.
1 min.
Step times:
The “Step Times” rotary switch is used to set the step time. There is a choice
of eight time (1 s, 3 s, 10 s, 30 s, 1 min., 3 min., 10 min. and 30 min.). The
step time is the time for which a particular scene is active before the next
scene is activated. Factory setting: 1 second
Step Time
30 s
DALI
U
3 min.
function
key
The end scene must be accessed by pressing
the switch briefly. Pressing the switch for more
than 5 seconds stores this as the end scene.
The saving of the final scenes is indicated by fast
stepping through all the scenes used, followed by
an OFF signal.
T
luxCONTROL
Scene 1
Scene 2
Scene 3
O
Scene 0
Example: For a step time of 30 seconds the module sends a new scene
command every 30 seconds.
DALI
Function switch
AS
E
Function switch closed
The sequencer module is active
Setting the fade time
Based on the normal DALI specification, the changes from one scene to the
next in a sequence would be extremely abrupt. The colours for the individual
scenes would come on instantly (within 0.7 s). To ensure that the transition
is smooth and gentle you can change the fade time in the ballasts. The time
during which the colour is changing can be set between 0.7 s and 90.5 s
with the aid of configTOOL software and a DALI USB (article no. 24138923).
D
Function
switch
Function switch open
The sequencer module is not active
Function switch is opened
The installation switches off because of the broadcast command “off” is sent.
Module switch
Up/Save switch ­↑
This switch is only active if the sequencer module is not activated
(Function switch is open).
PH
Up ­↑
Pressing the switch briefly calls up the next scene.
Save ­↑
Holding down the switch (for about 5 seconds) defines the current scene as
the last scene in the sequence. This setting is retained even after power-off.
Down/Reset switch ↓
This switch is only active if the sequencer module is not activated
(Function switch is open).
Down ↓
Pressing the switch briefly calls up the previous scene.
Reset ↓
Holding down the switch (for about 5 seconds) calls the broadcast
command “OFF”.
Data sheet 08/13-CO057-0 We reserve the right to make technical changes without prior notice.
Scene 0
Step Time
Scene 1
Scene 2
Scene 3
Fade Time
Note: If the step time is less than the fade time the next scene will be selected
even if the fade time has not been completed.

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project