GRANDE Series Commercial-grade, universal- mount, snap-fit Exit Sign

GRANDE Series Commercial-grade, universal- mount, snap-fit Exit Sign
Project/Location:
Contractor:
GRANDE™ Series
Date:
Commercial-grade, universalmount, snap-fit Exit Sign
FEATURES
Supply and install the Lumacell® Grande™ Series Exit Sign. The standard
equipment shall operate with a dual-voltage input of 120/347VAC with less
than 2W of consumption and a universal two-wire DC input voltage from 6VDC
to 48VDC at less than 2.5W for single and double face signs. The exit shall
be suitable for wall, end, or ceiling mount. The faceplate shall be constructed
of a durable high impact thermoplastic. No screws are necessary to hold the
faceplate or the back plate to the housing. The faceplates shall come standard
with snap in/out chevrons. The frame shall consist of a one-piece factory white
thermoplastic. The light source shall be light emitting diodes (LEDs). The LEDs
shall provide illumination in normal and emergency operation and shall be
mounted inside the exit housing. Red LED technology shall be ALINGAP. A LEDsensitive diffuser shall be mounted in front of the LEDs to provide the 6” high by
¾” stroke letters with even illumination. The Exit Sign shall be C860 approved.
The Exit Sign in a Self-Powered configuration shall be equipped with a sealed,
maintenance-free Nickel-Cadmium battery. The equipment shall recharge the
battery in 24 hours and stay illuminated at least 90 minutes upon AC failure.
The Self-Powered model equipped with advanced diagnostic shall self-test by
simulating a power failure for one minute every 30 days, 30 minutes every 60
days and 90 minutes every 360 days. A diagnostic circuit shall continuously
monitor the performance of the battery, charger module and LED lamps. Upon
failure detection the system shall display the error on the AC pilot lamp, which
will change color from green to red and will flash with a specific code. The
red light shall be steady-on in case of “Battery Disconnect”; it shall flash with
one blink for “Battery failure”, two blinks for “Charger failure” and four blinks
for “LED lamp failure. A label with the diagnostic legend shall be visible next
to the pilot light.
The equipment shall be Lumacell® Model:
.
diffusing lens and backplate.
•Universal, field-selectable snap in/out chevrons
•Available for wall, end or ceiling mounting
•Indirect refractive technology provides bright, even illumination
•Long-life, energy-efficient, ALINGAP LED light source
•Energy efficient – consumes less than 3.5W
•Normal AC and emergency DC operation with dual AC input of
120V/347V and universal DC input of 6V to 48V
•Comes with the lumacell EZ2 canopy for quick & easy installation.
See page 103 for information.
•CSA certified, meets or exceeds C860 requirements
WIRE GUARDS
Wall Mount
460.0027-L
End Mount
460.0028-L
Ceiling Mount
DIMENSIONS
8” [20.3cm]
Dimensions are approximate and subject to change.
9” [22.9cm]
Lumacell Model:
TYPICAL SPECIFICATIONS
•Durable, injection-molded, made in Canada thermoplastic housing
•Universal mounting - supplied standard with two stencil plates, red
460.0079-L
Prepared by:
IN THE SAME FAMILY: THERMOPLASTIC
117/8” [30.1cm]
- Grande™ Series Thermoplastic
Combination Unit
- Grande™ Series
Thermoplastic Battery Unit
p. 52
p. 108-109
2” [5.0cm]
127/8” [32.8cm]
POWER CONSUMPTION AND UNIT RATING
MODEL
AC SPECS
DC SPECS
AC only
120/347VAC
Less than 2.5W
-
-
AC/DC remote
120/347VAC
Less than 2W
6 to 48VDC
Less than 1.5W
Self-Powered
120/347VAC
Less than 3.5W
Nickel-Cadmium Battery
Minutes 90 minutes
Self-Powewed with diagnostic
120/347VAC
Less than 3W
Nickel-Cadmium Battery
Minutes 90 minutes
ORDERING INFORMATION
SERIES
COLOUR
UNIT TYPE
VOLTAGE
GRA= LED plastic
universal
Exit Sign
W= factory white
B= black
AC= AC only
AC2C1= dual AC circuit (2X 120V)
UNV= 120/277 or 120/347VAC & 6
to 48VDC
SPN= Self-Powered Ni-Cd
SDN= Self-Powered diagnostic Ni-Cd
2= 120/277VAC
3= 120/347VAC
EXAMPLE: GRAWAC2R
52
www.lumacell.com
LEGEND COLOUR
OPTIONS
R= red
G= green
R1= red single face*
R2= red double face*
G1= green single face*
G2= green double face*
TP= tamper-proof screws*
VRTP= polycarbonate shield with tamper-proof screws
BA= brushed aluminum stencil
990.0119-L= tamper-proof bit**
NEX= NEXUS® system interface***
NEXRF= wireless NEXUS® system interface***
* Used for special wording signs.
* Specify single or double face.
*** One bit needed per order.
*** Self-Powered models only.
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement