English Installation Manual of WHIRLPOOL RM280PXBB3

English Installation Manual of WHIRLPOOL RM280PXBB3
.. . ::.:
. .. .. :
.,..,.,..
. .,.,:.::..
...
..
...
..
,.,...::.....:
... ::.:...:.:.:.:.:.:...:.:.,.
.,:,:,.,
,.
IMPORTANT:
Read and save
these instructions.
IMPORTANT:
Installer: Leave Installation Instructions
with the homeowner.
Homeowner: Keep Installation Instructions
for future reference.
Save Installation Instructions for local
electrical inspector’s use.
30” Electr; Built-in
Combination
Microwave Oven and
Thermal Oven
Before you start...
Read the electrical and carpentry
instnrctions.
Proper installation is your responsibility. A
qualified technician should install this oven.
Make sure you have everything necessary
for correct installation. lt is the responsibility
of the installer to comply with the installation
clearances specified on the serial/rating
plate. The serial/rating plate can be found
behind the oven door on the front frame.
Check location where the buitt-in oven will
be installed. The location should be away
from strong draft areas, such as windows,
doors, and strong heating vents. The built-in
oven should be located for convenient use
in the kitchen.
Remove all packaging material from
microwave oven cavity. Check microwave
oven area for damage - see WARNING
below. If any damage is evident, do not
operate until microwave oven is checked
by an authorized service technician.
Cabinet opening dimensions that are
shown must be used. Given dimensions
provide minimum clearance.
The recessed installation area must provide
complete enclosure around the recessed
portion of the oven.
ALL OPENINGS IN THEWALL OR FLOOR
WHERETHE BUILT-INOVEN IS TO BE
INSTALLEDMUSTBESEALED.
Ik
Electrical ground is required. See
‘Electrical requirements.”
LT
cabinet
door
‘Nde: there nwst be 1” min.
betweonbottomot~net
door and top ol oven cansok
Electrical Shock Hazard
II Is the cudomer’s responsibllll:
*To contact a qualified electrical
installer.
*To assure that the electrical installatton
is adequate and in conformance with
National Electrical Code, ANSI/NFPA
70 - latest edition’, and all local
codes and ordinances.
Failure to do so could result in fire,
electrical shock or other personal injury.
Personal Injury Hazard
Securely fasten oven to cabinet using
the 4 screws provided.
Failure to do so could cause the oven to
move or tip during use and result in
personal injury.
rtecerced
oven
Ir--
I
\
L r
blnet.
IF
\
\
\
-\
i
DcBNotsd
01 ren to
cl
\
\
1Y mtn.
recopmended
so nwxowave
oven bottom Is
Important: Observe all governing
codes ordinances.
lhe oven support surface must be level
and flush wlttt the bottom of the cabinet
CUtOUt.
Tools needed for
Installation:
Electrical
reauhements
Electrtcal Shock Hazard
Electrical ground is required on this
appliance.
l Do Not ground to a gas pipe.
l Do Not have a fuse in the neutral or
grounding circuit. A fuse in the neutral or
grounding circuit could result in an
electrical shock.
l Check with a qualified
electrician if you
are in doubt as to whether the appliance
is properly grounded.
Failure to follow these instructions could
result in serious injury or death.
l
screwdrtver
Parts supplied for
installation:
If codes permit and a separate grounding
wire is used, it is recommended that a
qualified electrician determine that the
grounding path is adequate.
IMPORTANT:
Save Instalkrtion Instructions for the local
electrical inspector’s use.
Panel A
Excessive Mlcrowave Energy Exposure
Do Not attempt to operate the
microwave oven wtth the door open.
l DoNottamperwRhordefeatthe
safefy interlocks.
l Do Not place
objects between the
microwave oven front face and door.
l Do Not allow
soil or cleaner residue to
accumulate on sealing surface of the
microwave oven door.
l Do Not operate
the microwave oven if
-lwml Do Not operate
the microwave oven if:
- doorlsbent.
- hinges and latches are broken or
loose.
- door seals, sealing surfaces or
glass are broken.
lhe microwave oven door must close
properly to provide safe operation.
l
Only have a qualified repair person
adjust, repair and check microwave
oven for microwave leakage after a
repair is made.
l Do Not use microwave
for commercial
purposes. The microwave oven in thii
unit is designed for household use
only.
Failure to follow these instructions could
result In exposure to excessive
nlcrowave energy.
l
Cabinet Damage
Do Not block the oven vent.
Blocking the oven vent may cause
damage and poor baking performance.
Mobile home installation
The installation of this oven must conform
to the Manufactured Home Construction
and Safety Standards, Title 24 CFR, Part
3280 (formerly the Federal Standard for
Mobile Home Construction and Safety, Title
24, HUD Part 280) or when such standard is
not applicable, the Standard for
Manufactured Home Installation 1982
(Manufactured
Home Sites, Communities
and Setups), ANSI 2225. l-l 984, or latest
edition, or with local codes.
A four-wire, power supply cord must be
used in a mobile home installation. The
appliance wiring will need to be revised.
See *Electrical requirements.” Figure 3,
Panel B.
Copies of the standards listed may be
obtained from:
‘Nattonal Fire Protection Association
Batterymarch Park
Quincy, Massachusetts 02269
A
n A three-wire
or four-wire, single phase,
120/24&volt, 60-Hz, AC-only electrical supply
(or three-wire or four-wire 120/20&volt if
specified on the serial/rating plate) is
required on a separate, &ampere circuit,
fused in both sides of the line. Time-delay
fuse or circuit breaker is recommended.
The fuse size must not exceed the circuit
rating of the appliance specified on the
serial/rating plate. The serial/rating plate is
located behind the oven door on the front
frame.
B
OVEN MUSTBECONNECTED WlTH
COPPERWIREONLY.
C
n
Wire sizes and connections must
conform to the requirements of the National
Electrical Code, ANSI/NFPA 70 - latest
edition’, and all local codes and
ordinances. Wire sizes and connections must
conform with the rating of the appliance.
Copies of the standards listed may be
obtained from:
‘Nattonal Fire Protection
AssociationBatterymarch Park
Qulncy, Massachusetts 02269
I
I’ I
I
A. Where local codes
permit...
Now
start...
oven in kitchen.
WI
connecting of the cabinet-grounding
conductor to the neutral (white) junction
box wire:
cable from
power supply
n
junction
II I
1
I Remove shipping materials, tape,
and protective film from oven. Do Not
remove shipping base at this time.
2
m Remove the racks and other parts
from inside the oven. Remove the air grille
taped to the top or side of oven.
Personal Injury Hazard
Use both hands to remove oven doors.
l Grasp only the sides of oven doors.
l Do Not use handle
or any portion of
the front frame or trim for lifting.
. Because of the weight and size of the
ovens, two or more people are
needed to move and safely install the
ovens.
Failure to property grasp the oven
doors or to lift ovens properly could
result in damage to the product or
personal injury.
l
D
I This appliance should be
connected directly to the fused
disconnect (or circuit breaker box)
through flexible, armored or non-metallic
sheathed, copper cable (with grounding
wire). The flexible armored cable from the
appliance should be connected directly
to the junction box.
n Locate the junction box to allow as
much slack in the cable as possible
between the junction box and the
appliance so that the oven can be
moved if servicing is ever necessary.
Do Not cut the condult.
n A U.L.-listed conduit connector
be provided at the junction box.
must
Grounded Neutral
1. Disconnect the power supply.
2. Remove the terminal block cover.
3. Connect together 3 wires: green and
white appliance cable wires and the
neutral (white) wire in junction box.
4. Connect the two black wires together;
then connect the two red wires
together with wire connectors. See
Figure 1.
B. Where local codes Do
Not permit...
connecting the cabinet-grounding
conductor to the neutral (white) junction
box wire:
junction
cable from
Dower sur>tAv
G
n A wiring diagram
is included in the
Tech Sheet. The Tech Sheet is located
behind the control panel.
Electrical
connection
rlres
Figure 2
ElecMcalShockHazc~d
Electrical ground is required on thls
appliance.
l Do Not connect
to the electrical supply
until appliance is permanently
grounded.
l Disconnect
power to the junction box
before making the electrical
connection.
l lhii
appliance must be connected to a
grounded, metallic, permanent wiring
system, or a grounding connector
should be connected to the grounding
terminal or wire lead on the appliance.
Failure to do so could result in a fire,
personal injury or electrical shock.
l
This appliance is manufactured with white
(neutral) power supply wire and a
cabinet-connected
green grounding wire
twisted together.
Connect the appliance cable to the
junction box through the U.L.-listed conduit
connector. Complete electrical
connection according to local codes and
ordinances.
conduit
connector
cable
tram
oven
Ungrounded neutral
1. Disconnect power supply.
2. Separate the green and white
appliance cable wires.
3. Connect the white appliance cable
wire to the neutral (white) wire in the
junction box.
4. Connect the two black wires together;
then connect the two red wires
together with wire connectors. See
Figure 2.
5. Connect the green or bare grounding
wire from the appliance cable to a
grounded wire in the junction box.
C. If connecting to a fourwire electrical s stem...
Do Not connect the cab r net-grounding
conductor to the neutral (white) junction
box wire.
junction
I Insert a nail (or equivalent, 5/32”
diameter item) into the hole in each of the
hinges. Close the door as far as possible.
Lift the oven door off of the hinges. Set
aside.
Before movlng ovens across floor, check
that ovens are on shipping base or slide
ovens onto cardboard or hardboard.
Failure to follow these instructions may
result in damage to floor covering.
4
n
Disconnect power supply. Move
oven close to final position. Remove and
discard shipping base, cardboard or
hardboard. Feed appliance cable
through the opening in cabinet. Make
electrical connection. See “Electrical
requirements” and -Electrical connection”
sections, Panels A and B.
cable from
power supply
4
~black
wires
&FL-My
Figure
3
-
Panel B
cable
from
oven
connector
1. D&connect the power supply.
2. Separate the green (or bare) and white
appliance cable wires.
3. Connect the white appliance cable
wire to the neutral (white) wire in the
junction box.
4. Connect the two black wires together;
then connect the two red wires
together with wire connectors. See
Figure 3.
5. Connect the green appliance cable
wire to the green grounding wire in the
junction box.
5
n Lift oven up into cabinet cutout
using the oven opening as an area to grip.
Carefully push against the seal area of
the oven front frame when pushing the
oven into the cabinet.
Do Not push against outside edges.
Failure to follow these instructions can
result in damage to oven finish.
9
Push against seal area of front frame to
push oven into cabinet.
n
Turn on the power supply.
‘PF’ should appear in the oven
temperature display and ‘888:88” should
appear in the microwave display. To set
the time of day, press the ‘CLOCK/SET’
pad. ‘TIME, HR, and MIN’ will light in the
display. Either ‘0O:oO’ or a time will
appear and -:I will be flashing. Press the
‘HR’ and ‘MIN’ arrows to set the clock to
the correct time of day. Press the
“START/ENTER’pad to start the clock.
12
n
Check the operation of the
mkrowave oven.
l
Fill a microwave-safe container with one
cup (25Oml) of water and place
container inside microwave oven. Close
door firmly.
l Set microwave
oven cook time to “200’
minutes.
l
Press the START/ENTER” pad. The interior
microwave oven light should be on and
the remaining cooking time should be
displayed.
l When display
reads n 1:oO,” open
microwave oven door. The microwave
should stop cooking.
l Close door firmly. The interior microwave
oven light should turn off.
l
Press the “START/ENTER”pad. Microwave
oven should begin cooking and the
microwave oven interior light should be
on.
l
Let microwave oven complete cooking
time. A tone will sound four times at end
of cooking time and microwave oven
will shut off.
. Open microwave oven door and
carefully remove container. Water in
container should be hot.
10
Personal Injury/Product Damage
Hazard
Securely fasten oven to cabinet using
the four screws provided.
Failure to do so could cause the oven
to move or tip during use and result in
personal injury or product damme.
w Check the ooeration of the
oven. Press the ‘BAKE’ pad. ‘350” will
appear in the display. Press the
“START/ENTER”pad to start the bake
operation. In l-2 minutes, the bottom
element should glow red. The upper
element should become hot, but not glow
red. Press the “OFF/CANCEL” pad.
11
n
Check the oDercrlion of the
oven broil element. Press the -BROIL’ pad.
-500”’ will appear in the display. Press
the-START/ENTER” pad to start the broil
operation. In l-2 minutes, the upper
element should glow red.
Press the “OFF/CANCEL” pad.
6
You have just finished installing your
new oven. To get the most efficient use
from your new oven, read your l&e &
Care Guide. Keep Installation
Instructions and Guide close to oven for
easy reference. lhe instructions will
make reinstalling your oven in another
home as easy as the first installation.
SCreWI
I
= Center oven into cabinet cutout.
Use four screws through the mounting
holes in the front frame of the oven to
secure the oven to the cabinet. Do Not
overtighten screws.
7
n Put the air grille in place below the
oven opening, making sure that the
louvers in the air grille point down, the
flange is at the bottom, and the mounting
holes are at the top. Slide the air grille into
positlon and attach it to the oven cabinet
with the three, black or chrome, metal
screws provided.
Replace the oven racks.
Replace the oven door by fitting both
corners of the door over the ends of the
hinges. Remove the nails from the hinges,
Close the oven door. If the door does not
close, you have not pushed the door
completely onto the hinges.
Panel C
4.
1
If the oven does
not operate...
l
l
Check that the circuit breaker is not
tripped or the house fuse blown.
See Use and Care Guide for
troubleshooting checklist.
NOTE:
Refer to Use and Care Guide for
operating instructions and cleaning
instructions.
Part No. 3184431 Rev. C
0 1994 Whirlpool Corporation
If you need
assistance...
If you have questions about operating or
maintaining your oven not covered in the
Installation Instructions, call 1-800-253-l 301.
When you call, you will need the oven
model number and serial number. Both
numbers can be found on the serial/rating
plate located behind the oven door on
the front frame.
Printed on recycled paper.
10% post consumer waste/
50% &covered
materials.
Benton Harbor, Michigan 49022
Printed in U.S.A.
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement