Savin C2824 Operating instructions

Savin C2824 Operating instructions
Paper type: OK Prince Eco G100(55kg), Paper Thickness=80 µm // Pages in book=192 // Print scale=81%
Gap (when printed at 81% scale) = Pages in book × Paper thickness / 2 = 7.680000 mm
Operating Instructions
General Settings Guide
Getting Started
Combined Function Operations
Document Server
User Tools (System Settings)
Troubleshooting
Remarks
Entering Text
Specifications
Type for C2824/DSc428/LD328c/Aficio 3228C
Type for C3528/DSc435/LD335c/Aficio 3235C
Type for C4535/DSc445/LD345c/Aficio 3245C
Printed in Japan
EN USA B180-7505
B1807505
Read this manual carefully before you use this machine and keep it handy for future reference. For safe and correct use, be sure to read the Safety
Information in this manual before using the machine.
Paper type: OK Prince Eco G100(55kg), Paper Thickness=80 µm // Pages in book=192 // Print scale=81%
Gap (when printed at 81% scale) = Pages in book × Paper thickness / 2 = 7.680000 mm
Introduction
This manual contains detailed instructions and notes on the operation and use of this machine. For your
safety and benefit, read this manual carefully before using the machine. Keep this manual in a handy
place for quick reference.
In accordance with IEC 60417, this machine uses the following symbols for the main power switch:
a means POWER ON.
b means POWER OFF.
c means STAND BY.
Important
Contents of this manual are subject to change without prior notice. In no event will the company be liable for direct, indirect, special, incidental, or consequential damages as a result of handling or operating the machine.
Notes:
Some illustrations in this manual might be slightly different from the machine.
Certain options might not be available in some countries. For details, please contact your local dealer.
Laser Safety:
CDRH Regulations
This equipment complies with requirements of 21 CFR Subchapter J for class 1 laser products. This
equipment contains five AlGalnP laser diodes, 7–milliwatt, 645–660 nanometer wavelength for each
emitter. This equipment does not emit hazardous light, since the beam is totally enclosed during all customer modes of operation and maintenance.
Caution:
Use of controls or adjustments or performance of procedures other than those specified in this manual
might result in hazardous radiation exposure.
Notes:
The model names of the machines do not appear in the following pages. Check the type of your machine before reading this manual. (For details, see P.17 “Machine Types”.)
•
Type 1: C2824/DSc428/LD328c/Aficio 3228C
•
Type 2: C3528/DSc435/LD335c/Aficio 3235C
•
Type 3: C4535/DSc445/LD345c/Aficio 3245C
Certain types might not be available in some countries. For details, please contact your local dealer.
Two kinds of size notation are employed in this manual. With this machine refer to the inch version.
For good copy quality, the supplier recommends that you use genuine toner from the supplier.
The supplier shall not be responsible for any damage or expense that might result from the use of parts
other than genuine parts from the supplier with your office products.
Power Source
120V, 60Hz, 12A or more
Please be sure to connect the power cord to a power source as shown above. For details about power
source, see P.149 “Power Connection”.
Copyright © 2004
JupiterC2_GSG_EN_Pre_FM.book Page i Tuesday, December 28, 2004 1:39 PM
Manuals for This Machine
The following manuals describe the operational procedures of this machine. For
particular functions, see the relevant parts of the manual.
Note
❒ Manuals provided are specific to machine type.
❒ Adobe Acrobat Reader/Adobe Reader is necessary to view the manuals as a
PDF file.
❒ Two CD-ROMs are provided:
• CD-ROM 1 “Operating Instructions”
• CD-ROM 2 “Scanner Driver and Document Management Utility”
❖ General Settings Guide (this manual)
Provides an overview of the machine and describes System Settings (such as
Tray Paper Settings), Document Server functions, and troubleshooting.
Refer to this manual for Address Book procedures such as registering fax
numbers, e-mail addresses, and user codes.
❖ Security Reference
This manual is for administrators of this machine. It describes security functions that the administrators can use to protect data from being tampered, or
prevent the machine from unauthorized use.
Also refer to this manual for the procedures for registering administrators, as
well as setting user and administrator authentication.
❖ Network Guide (PDF file - CD-ROM1)
Provides information about configuring and operating the printer in a network environment or using software.
This manual covers all models, and therefore contains functions and settings
that may not be available for your model. Images, illustrations, functions, and
supported operating systems may differ from those of your model.
❖ Copy Reference
Describes operations, functions, and troubleshooting for the machine's copier
function.
❖ Facsimile Reference <Basic Features>
Describes operations, functions, and troubleshooting for the machine's facsimile function.
❖ Facsimile Reference <Advanced Features>
Describes advanced facsimile functions such as line settings and procedures
for registering IDs.
❖ Printer Reference
Describes system settings, operations, functions, and troubleshooting for the
machine's printer function.
i
JupiterC2_GSG_EN_Pre_FM.book Page ii Tuesday, December 28, 2004 1:39 PM
❖ Scanner Reference (PDF file - CD-ROM1)
Describes operations, functions, and troubleshooting for the machine's scanner function.
❖ Manuals for DeskTopBinder Lite
DeskTopBinder Lite is a utility included on the CD-ROM labeled “Scanner
Driver & Document Management Utilities”.
• DeskTopBinder Lite Setup Guide (PDF file - CD-ROM2)
Describes installation of, and the operating environment for DeskTopBinder Lite in detail. This guide can be displayed from the [Setup] display
when DeskTopBinder Lite is installed.
• DeskTopBinder Introduction Guide (PDF file - CD-ROM2)
Describes operations of DeskTopBinder Lite and provides an overview of
its functions. This guide is added to the [Start] menu when DeskTopBinder
Lite is installed.
• Auto Document Link Guide (PDF file - CD-ROM2)
Describes operations and functions of Auto Document Link installed with
DeskTopBinder Lite. This guide is added to the [Start] menu when DeskTopBinder Lite is installed.
❖ Other manuals
• PS3 Supplement (PDF file - CD-ROM1)
• Unix Supplement (Available from an authorized dealer, or as a PDF file on
our Web site.)
ii
JupiterC2_GSG_EN_Pre_FM.book Page iii Tuesday, December 28, 2004 1:39 PM
What You Can Do with This Machine
The following introduces the functions of this machine, and the relevant manuals containing detailed information about them.
Products marked with * are optional. For details about optional products, see
p.166 “Options”, or contact your local dealer.
Copier, Facsimile, Printer, and
Scanner Functions
Utilizing Stored Documents
ADL002S
ADL001S
This machine provides copier, facsimile*, printer, and scanner functions.
• You can make copies of originals.
With a finisher*, you can sort and
staple copies. See Copy Reference.
• You can send originals by fax and
receive faxes from other parties.
See Facsimile Reference <Basic Features> , and Facsimile Reference
<Advanced Features>.
• You can print documents created
using applications. See Printer Reference.
• You can scan originals and send
the scan file to a computer. See
Scanner Reference.
• You can store file from originals
scanned by this machine, or file
sent from other computers, into
the machine's hard disk. You can
print and fax stored documents as
required. You can also change
print settings and print multiple
documents (Document Server).
See p.39 “Using the Document
Server”.
• With DeskTopBinder Professional*/Lite, you can search, check,
print, and delete stored documents
using your computer. You can also
retrieve stored documents scanned
in scanner mode. With File Format
Converter*, you can even download documents stored in copy and
printer functions to your computer. See Network Guide.
iii
JupiterC2_GSG_EN_Pre_FM.book Page iv Tuesday, December 28, 2004 1:39 PM
Paperless Fax Transmission
and Reception
Fax Transmission and
Reception Through the
Internet
Reception
ADL008S
ADL003S
• You can store received fax messages on the machine's hard disk, instead of printing them onto paper.
You can use DeskTopBinder Professional*/Lite or a Web browser
to check, print, delete, retrieve, or
download documents using your
computer (Storing received documents). See Facsimile Reference
<Advanced Features>.
Transmission
ADL004S
• You can send documents created
using applications to another party's fax machine directly, without
performing a print job (LAN-Fax).
See Facsimile Reference <Advanced
Features>.
iv
• You can send fax documents
through e-mail by specifying the
recipient's e-mail address (Internet
Fax Transmission).
You can receive sent documents
via Internet Fax, or from computers (Internet Fax Reception). See
Facsimile Reference <Basic Features>.
• You can send faxes by using data
such as the IP address to specify
the IP-Fax destination (IP-Fax
Transmission).
The transmitted files can be received using an Internet fax machine (IP-Fax Reception). See
Facsimile Reference <Basic Features>.
JupiterC2_GSG_EN_Pre_FM.book Page v Tuesday, December 28, 2004 1:39 PM
Using the Scanner in a
Network Environment
Administrating the
Machine/Protecting
Documents (Security
Functions)
ADL005S
• You can send scanned documents
to other network computers using
e-mail (Sending stored scan file by
e-mail). See Scanner Reference.
• With ScanRouter delivery software, you can save scanned documents in specified destinations on
network computers (File storage).
See Scanner Reference.
• You can send scanned documents
to other network folders (Scan to
Folder). See Scanner Reference.
ADL006S
• You can protect documents from
unauthorized access and stop
them from being copied without
permission. See Security Reference.
• You can control the use of the machine, as well as prevent machine
settings from being changed without authorization. See Security Reference.
• By setting passwords, you can prevent unauthorized access via the
network. See Security Reference.
• You can erase the data on the hard
disk to prevent the information
from leaking out. See the manual
for the DataOverWriteSecurity
unit* and Security Reference.
v
JupiterC2_GSG_EN_Pre_FM.book Page vi Tuesday, December 28, 2004 1:39 PM
Monitoring the Machine Via
Computer
ADL007S
You can monitor machine status and
change settings using a computer.
• Using SmartDeviceMonitor for
Admin, SmartDeviceMonitor for
Client, or a Web browser, you can
use a computer to view the machine's status, such as to check on
paper quantities, or misfeeds, etc.
See Network Guide.
• You can also use a Web browser to
make network settings. See Network Guide.
• You can also use a Web browser to
register and manage items such as
user codes, fax numbers, e-mail
addresses, and folders in the Address Book. See the Web browser's
Help.
vi
JupiterC2_GSG_EN_Pre_FM.book Page vii Tuesday, December 28, 2004 1:39 PM
TABLE OF CONTENTS
Manuals for This Machine ...................................................................................... i
What You Can Do with This Machine.................................................................. iii
Copier, Facsimile, Printer, and Scanner Functions ................................................... iii
Utilizing Stored Documents ....................................................................................... iii
Paperless Fax Transmission and Reception............................................................. iv
Fax Transmission and Reception Through the Internet ............................................ iv
Using the Scanner in a Network Environment ........................................................... v
Administrating the Machine/Protecting Documents (Security Functions) .................. v
Monitoring the Machine Via Computer...................................................................... vi
Notice ......................................................................................................................1
Copyrights and Trademarks .................................................................................4
Trademarks ................................................................................................................4
Information about Installed Software.......................................................................... 5
How to Read This Manual ................................................................................... 11
Safety Information ............................................................................................... 12
Safety During Operation........................................................................................... 12
Positions of Labels and Hallmarks for RWARNING and RCAUTION............ 14
ENERGY STAR Program ..................................................................................... 15
Machine Types ..................................................................................................... 17
1. Getting Started
Guide to Components ......................................................................................... 19
External Options....................................................................................................... 21
Internal Options........................................................................................................ 22
Control Panel........................................................................................................ 23
Display Panel ........................................................................................................... 25
When the Authentication Screen is displayed.......................................................... 26
Turning On the Power ......................................................................................... 28
Turning On the Main Power ..................................................................................... 28
Turning On the Power .............................................................................................. 28
Turning Off the Power .............................................................................................. 29
Turning Off the Main Power ..................................................................................... 29
Saving Energy .......................................................................................................... 30
2. Combined Function Operations
Changing Modes .................................................................................................. 31
Multi-Access......................................................................................................... 33
3. Document Server
Relationship between Document Server and Other Functions ....................... 37
Document Server Display ........................................................................................ 38
Using the Document Server................................................................................ 39
Storing Data ............................................................................................................. 39
Changing a Stored Document's File Name, User Name, or Password.................... 42
Selecting a Document .............................................................................................. 42
Searching for Stored Documents ............................................................................. 43
vii
JupiterC2_GSG_EN_Pre_FM.book Page viii Tuesday, December 28, 2004 1:39 PM
Printing Stored Documents ...................................................................................... 44
Deleting Stored Documents ..................................................................................... 47
Viewing Stored Documents Using a Web Browser .................................................. 47
Downloading Stored Documents.............................................................................. 48
Settings for the Document Server...................................................................... 49
4. User Tools (System Settings)
User Tools Menu (System Settings)................................................................... 51
Accessing User Tools (System Settings) .......................................................... 54
Changing Default Settings ....................................................................................... 54
Exiting User Tools .................................................................................................... 54
Settings You Can Change with User Tools ....................................................... 55
General Features ..................................................................................................... 55
Tray Paper Settings ................................................................................................. 58
Timer Settings .......................................................................................................... 61
Administrator Tools .................................................................................................. 63
Address Book....................................................................................................... 70
Registering Names .............................................................................................. 73
Registering a Name ................................................................................................. 73
Changing a Registered Name.................................................................................. 73
Deleting a Registered Name .................................................................................... 74
Authentication Information ................................................................................. 75
Registering a New User Code.................................................................................. 75
Changing a User Code............................................................................................. 76
Deleting a User Code............................................................................................... 76
Displaying the Counter for Each User Code ............................................................ 77
Printing the Counter for Each User Code................................................................. 77
Clearing the Number of Prints.................................................................................. 78
Fax Destination .................................................................................................... 79
Registering a Fax Destination .................................................................................. 80
Changing a Registered Fax Destination .................................................................. 82
Deleting a Registered Fax Destination..................................................................... 83
Registering an IP-Fax Destination ........................................................................... 84
Changing a Registered IP-Fax Destination.............................................................. 85
E-mail Destination................................................................................................ 86
Registering an E-mail Destination ............................................................................ 86
Changing a Registered E-mail Destination .............................................................. 87
Deleting a Registered E-mail Destination ................................................................ 88
Registering Folders ............................................................................................. 89
Using SMB to Connect............................................................................................. 89
Using FTP to Connect.............................................................................................. 93
Registering Names to a Group ........................................................................... 96
Registering a New Group ......................................................................................... 96
Registering Names to a Group................................................................................. 97
Displaying Names Registered in Groups ................................................................. 97
Removing a Name from a Group ............................................................................. 98
Changing a Group Name ......................................................................................... 98
Deleting a Group ...................................................................................................... 99
Adding a Group to Another Group ........................................................................... 99
Deleting a Group within a Group.............................................................................. 99
viii
JupiterC2_GSG_EN_Pre_FM.book Page ix Tuesday, December 28, 2004 1:39 PM
Registering a Protection Code ......................................................................... 101
Registering a Protection Code To a Single User ...................................................101
Registering a Protection Code To a Group User ...................................................102
Registering the Transfer Request .................................................................... 103
Registering a Transfer Station/Receiving Station .................................................. 103
Changing a Registered Transfer Station/Receiving Station ...................................105
Deleting a Registered Transfer Station/Receiving Station .....................................106
Registering SMTP and LDAP Authentication.................................................. 107
SMTP Authentication .............................................................................................107
LDAP Authentication ..............................................................................................108
5. Troubleshooting
If Your Machine Does Not Operate As You Want............................................ 109
General ..................................................................................................................109
Document Server ...................................................................................................112
Maintenance...........................................................................................................112
BLoading Paper ................................................................................................ 113
Loading Paper into Paper Trays and Paper Tray Unit ........................................... 113
Loading Paper into Large Capacity Tray (optional)................................................114
DAdding Toner.................................................................................................. 116
Inserting Toner .......................................................................................................117
xClearing Misfeeds .......................................................................................... 119
Changing the Paper Size................................................................................... 128
Changing the Paper Size of the Paper Tray ..........................................................128
If you load a paper size that is not selected automatically .....................................129
dAdding Staples............................................................................................... 131
2 Tray Finisher .......................................................................................................131
Booklet Finisher .....................................................................................................132
Removing Jammed Staples .............................................................................. 133
2 Tray Finisher .......................................................................................................133
Booklet Finisher .....................................................................................................134
yRemoving Punch Waste ................................................................................ 135
2 Tray Finisher .......................................................................................................135
Booklet Finisher .....................................................................................................136
Replacing the Stamp Cartridge ........................................................................ 137
Adjusting the Color Registration...................................................................... 138
Auto Color Registration .......................................................................................... 138
Fuser Adjustment for Thick Paper..........................................................................138
Checking the Fuser Adjustment Sheet...................................................................141
Auto Color Calibration ............................................................................................142
6. Remarks
Dos and Don'ts................................................................................................... 145
Saving Color Copies.......................................................................................... 146
Toner ................................................................................................................... 147
Handling Toner.......................................................................................................147
Toner Storage ........................................................................................................147
Used Toner ............................................................................................................147
ix
JupiterC2_GSG_EN_Pre_FM.book Page x Tuesday, December 28, 2004 1:39 PM
Where to Put Your Machine .............................................................................. 148
Machine Environment ............................................................................................148
Moving....................................................................................................................148
Power Connection..................................................................................................149
Access to the Machine ...........................................................................................149
Maintaining Your Machine ................................................................................ 150
Cleaning the Exposure Glass.................................................................................150
Cleaning the Exposure Glass Cover ...................................................................... 150
Cleaning the Auto Document Feeder.....................................................................150
Cleaning the Dustproof Glass .......................................................................... 151
Earth Leakage Breaker ...................................................................................... 152
Replacing the Waste Toner Bottle.................................................................... 154
Other Functions ................................................................................................. 156
Inquiry ....................................................................................................................156
Changing the Display Language ............................................................................156
Changing Paper Thickness Settings ...................................................................... 157
Counter ............................................................................................................... 158
Displaying the Total Counter..................................................................................158
7. Entering Text
Entering Text ...................................................................................................... 159
Available Characters ..............................................................................................159
Keys .......................................................................................................................159
How to Enter Text ..................................................................................................160
8. Specifications
Main Unit............................................................................................................. 161
Options ............................................................................................................... 166
Exposure Glass Cover ...........................................................................................166
Auto Document Feeder .......................................................................................... 166
2 Tray Finisher .......................................................................................................167
Punch Kit (2 tray finisher).......................................................................................168
Booklet Finisher .....................................................................................................168
Punch Kit (Booklet finisher)....................................................................................170
1 Tray Paper Unit ...................................................................................................170
2 Tray Paper Unit ...................................................................................................171
Large Capacity Tray...............................................................................................171
Scanner Accessibility Unit......................................................................................172
Copy Paper ......................................................................................................... 173
Recommended Paper Sizes and Types.................................................................173
Unusable Paper .....................................................................................................176
Paper Storage ........................................................................................................177
INDEX....................................................................................................... 178
x
JupiterC2_GSG_EN_Pre_FM.book Page 1 Tuesday, December 28, 2004 1:39 PM
Notice
Notice To Wireless LAN Interface (option) Users
Notes to users
It is strictly forbidden to use antenna(s) except designated.
A The antenna(s) of this device must not be co-located or operating in conjunction with any other antenna or transmitter.
B This equipment complies with FCC RF radiation exposure limits set forth for
an uncontrolled environment. End users must follow the specific operating
instructions for satisfying RF exposure compliance.
Notes to users in the United States of America
Notice:
This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed
to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause
harmful interference to radio communications. However, there is no guarantee
that interference will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which
the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
This device complies with part 15 of the FCC Rules.
Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired
operation.
Warning
Changes or modifications not expressly approved by the party responsible for
compliance could void the user's authority to operate the equipment.
1
JupiterC2_GSG_EN_Pre_FM.book Page 2 Tuesday, December 28, 2004 1:39 PM
Note to users in Canada
Note:
This Class B digital apparatus complies with Canadian ICES-003.
Operation is subject to the following two conditions:
(1) This device may not cause interference, and (2) this device must accept any
interference, including interference that may cause undesired operation of the
device.
IEEE 802.11b Interface Unit Type H:
This device complies with RSS-210 of Industry Canada.
The term “IC:” before the certification/registration number only signifies that
the Industry Canada technical specifications were met.
To prevent radio interference to the licensed service, this device is intended to
be operated indoors and away from windows to provide maximum shielding.
Equipment (or its transmit antenna) that is installed outdoors is subject to licensing.
To reduce potential radio interference to other users, the antenna type and its
gain should be so chosen that the equivalent isotropically radiated power (EIRP)
is not more than that required for successful communication.
This device has been designed to operate with an antenna having a maximum
gain of [0.45] dBi. Antenna having a higher gain is strictly prohibited per regulations of Industry Canada. The required antenna impedance is [50] ohms.
Remarque concernant les utilisateurs au Canada
Avertissement:
Cet appareil numérique de la classe B est conforme á la norme NMB-003 du Canada.
L'utilisation de ce dispositif est autorisée seulement aux conditions suivantes: (1)
il ne doit pas produire de brouillage et (2) l'utilisateur du dispositif doit être prêt
á accepter tout brouillage radioélectrique reçu, même si ce brouillage est susceptible de compromettre le fonctionnement du dispositif.
IEEE 802.11b Interface Unit Type H:
Ce dispositif est conforme á la norme CNR-210 d'Industrie Canada.
L'expression «IC:» avant le numéro d'homologation/enregistrement signifie
seulement que les spécifications techniques d'Industrie Canada ont été respectées.
Pour empêcher que cet appareil cause du brouillage au service faisant l'objet
d'une licence, il doit être utilisé á l'intérieur et devrait être placé loin des fenêtres
afin de fournir un écran de blindage maximal.
Si le matériel (ou son antenne d'emission) est installe á l'extérieur, il doit faire
l'objet d'une licence.
2
JupiterC2_GSG_EN_Pre_FM.book Page 3 Tuesday, December 28, 2004 1:39 PM
Afin de réduire le risque d'interférence aux autres utilisateurs, le type d'antenne
et son gain doivent être choisis de façon á ce que la puissance isotrope rayonnée
équivalente (p.i.r.e.) ne soit pas supérieure au niveau requis pour obtenir une
communication satisfaisante.
Ce dispositif a été conçu pour fonctionner avec une antenne ayant un gain maximal de [0.45] dBi.Une antenne ayant un gain plus élevé est strictement interdite
par les réglements d'Industrie Canada.L'impédance d'antenne requise est [50]
ohms.
3
JupiterC2_GSG_EN_Pre_FM.book Page 4 Tuesday, December 28, 2004 1:39 PM
Copyrights and Trademarks
Trademarks
Microsoft®, Windows® and Windows NT® are registered trademarks of Microsoft Corporation in the United States and/or other countries.
Acrobat® is a registered trademark of Adobe Systems Incorporated.
Bluetooth™ is a trademark of the Bluetooth SIG, Inc. (Special Interest Group)
and is used by RICOH Company Limited under license.
Copyright ©2001 Bluetooth SIG, Inc.
The Bluetooth Trademarks are owned by Bluetooth SIG, Inc. USA
Other product names used herein are for identification purposes only and might
be trademarks of their respective companies. We disclaim any and all rights to
those marks.
The proper names of the Windows operating systems are as follows:
• The product name of Windows® 95 is Microsoft® Windows® 95
• The product name of Windows® 98 is Microsoft® Windows® 98
• The product name of Windows® Me is Microsoft® Windows® Millennium
Edition (Windows Me)
• The product names of Windows® 2000 are as follows:
Microsoft® Windows® 2000 Advanced Server
Microsoft® Windows® 2000 Server
Microsoft® Windows® 2000 Professional
• The product names of Windows® XP are as follows:
Microsoft® Windows® XP Professional
Microsoft® Windows® XP Home Edition
• The product names of Windows Server™ 2003 are as follows:
Microsoft® Windows Server™ 2003 Standard Edition
Microsoft® Windows Server™ 2003 Enterprise Edition
Microsoft® Windows Server™ 2003 Web Edition
• The product names of Windows® NT are as follows:
Microsoft® Windows NT® Server 4.0
Microsoft® Windows NT® Workstation 4.0
4
JupiterC2_GSG_EN_Pre_FM.book Page 5 Tuesday, December 28, 2004 1:39 PM
Information about Installed Software
expat
• The software including controller, etc. (hereinafter "software") installed on
this product uses the expat Version under the conditions mentioned below.
• The product manufacturer provides warranty and support to the software of
the product including the expat, and the product manufacturer makes the initial developer and copyright holder of the expat, free from these obligations.
• Information relating to the expat is available at:
http://expat.sourceforge.net/
Copyright © 1998, 1999, 2000 Thai Open Source Software Center, Ltd. and Clark
Cooper.
Copyright © 2001, 2002 Expat maintainers.
Permission is hereby granted, free of charge, to any person obtaining a copy of
this software and associated documentation files (the "Software"), to deal in the
Software without restriction, including without limitation the rights to use,
copy, modify, merge, publish, distribute, sublicense, and/or sell copies of the
Software, and to permit persons to whom the Software is furnished to do so, subject to the following conditions:
The above copyright notice and this permission notice shall be included in all
copies or substantial portions of the Software.
THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY
KIND, EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE
WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR
PURPOSE AND NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY, WHETHER IN AN ACTION OF CONTRACT,
TORT OR OTHERWISE, ARISING FROM, OUT OF OR IN CONNECTION
WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN THE SOFTWARE.
NetBSD
1. Copyright Notice of NetBSD
For all users to use this product:
This product contains NetBSD operating system:
For the most part, the software constituting the NetBSD operating system is not
in the public domain; its authors retain their copyright.
The following text shows the copyright notice used for many of the NetBSD
source code. For exact copyright notice applicable for each of the files/binaries,
the source code tree must be consulted.
A full source code can be found at http://www.netbsd.org/.
Copyright © 1999, 2000 The NetBSD Foundation, Inc.
All rights reserved.
5
JupiterC2_GSG_EN_Pre_FM.book Page 6 Tuesday, December 28, 2004 1:39 PM
6
Redistribution and use in source and binary forms, with or without modification, are permitted provided that the following conditions are met:
A Redistributions of source code must retain the above copyright notice, this list
of conditions and the following disclaimer.
B Redistributions in binary form must reproduce the above copyright notice,
this list of conditions and the following disclaimer in the documentation
and/or other materials provided with the distribution.
C All advertising materials mentioning features or use of this software must
display the following acknowledgment:
This product includes software developed by The NetBSD Foundation, Inc.
and its contributors.
D Neither the name of The NetBSD Foundation nor the names of its contributors may be used to endorse or promote products derived from this software
without specific prior written permission.
THIS SOFTWARE IS PROVIDED BY THE NETBSD FOUNDATION, INC. AND
CONTRIBUTORS ''AS IS'' AND ANY EXPRESS OR IMPLIED WARRANTIES,
INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE FOUNDATION OR CONTRIBUTORS
BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF
USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER
CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE,
EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
2.Authors Name List
All product names mentioned herein are trademarks of their respective owners.
The following notices are required to satisfy the license terms of the software
that we have mentioned in this document:
• This product includes software developed by the University of California,
Berkeley and its contributors.
• This product includes software developed by Jonathan R. Stone for the NetBSD Project.
• This product includes software developed by the NetBSD Foundation, Inc.
and its contributors.
• This product includes software developed by Manuel Bouyer.
• This product includes software developed by Charles Hannum.
• This product includes software developed by Charles M. Hannum.
• This product includes software developed by Christopher G. Demetriou.
• This product includes software developed by TooLs GmbH.
• This product includes software developed by Terrence R. Lambert.
• This product includes software developed by Adam Glass and Charles Hannum.
• This product includes software developed by Theo de Raadt.
JupiterC2_GSG_EN_Pre_FM.book Page 7 Tuesday, December 28, 2004 1:39 PM
• This product includes software developed by Jonathan Stone and Jason R.
Thorpe for the NetBSD Project.
• This product includes software developed by the University of California,
Lawrence Berkeley Laboratory and its contributors.
• This product includes software developed by Christos Zoulas.
• This product includes software developed by Christopher G. Demetriou for
the NetBSD Project.
• This product includes software developed by Paul Kranenburg.
• This product includes software developed by Adam Glass.
• This product includes software developed by Jonathan Stone.
• This product includes software developed by Jonathan Stone for the NetBSD
Project.
• This product includes software developed by Winning Strategies, Inc.
• This product includes software developed by Frank van der Linden for the
NetBSD Project.
• This product includes software developed for the NetBSD Project by Frank
van der Linden
• This product includes software developed for the NetBSD Project by Jason R.
Thorpe.
• The software was developed by the University of California, Berkeley.
• This product includes software developed by Chris Provenzano, the University of California, Berkeley, and contributors.
Sablotron
Sablotron (Version 0.82) Copyright © 2000 Ginger Alliance Ltd. All Rights Reserved
a) The application software installed on this product includes the Sablotron software Version 0.82 (hereinafter, "Sablotron 0.82"), with modifications made by
the product manufacturer. The original code of the Sablotron 0.82 is provided by
Ginger Alliance Ltd., the initial developer, and the modified code of the Sablotron 0.82 has been derived from such original code provided by Ginger Alliance Ltd.
b) The product manufacturer provides warranty and support to the application
software of this product including the Sablotron 0.82 as modified, and the product manufacturer makes Ginger Alliance Ltd., the initial developer of the Sablotron 0.82, free from these obligations.
c) The Sablotron 0.82 and the modifications thereof are made available under the
terms of Mozilla Public License Version 1.1 (hereinafter, "MPL 1.1"), and the application software of this product constitutes the "Larger Work" as defined in
MPL 1.1. The application software of this product except for the Sablotron 0.82
as modified is licensed by the product manufacturer under separate agreement(s).
d) The source code of the modified code of the Sablotron 0.82 is available at: http://support-download.com/services/device/sablot/notice082.html
7
JupiterC2_GSG_EN_Pre_FM.book Page 8 Tuesday, December 28, 2004 1:39 PM
e) The source code of the Sablotron software is available at: http://www.gingerall.com
f) MPL 1.1 is available at: http://www.mozilla.org/MPL/MPL-1.1.html
JPEG LIBRARY
• The software installed on this product is based in part on the work of the Independent JPEG Group.
SASL
CMU libsasl
Tim Martin
Rob Earhart
Rob Siemborski
Copyright © 2001 Carnegie Mellon University. All rights reserved.
Redistribution and use in source and binary forms, with or without modification, are permitted provided that the following conditions are met:
A Redistributions of source code must retain the above copyright notice, this list
of conditions and the following disclaimer.
B Redistributions in binary form must reproduce the above copyright notice,
this list of conditions and the following disclaimer in the documentation
and/or other materials provided with the distribution.
C The name "Carnegie Mellon University" must not be used to endorse or promote products derived from this software without prior written permission.
For permission or any other legal details, please contact:
Office of Technology Transfer
Carnegie Mellon University
5000 Forbes Avenue
Pittsburgh, PA 15213-3890
(412) 268-4387, fax: (412) 268-7395
[email protected]
D Redistributions of any form whatsoever must retain the following acknowledgment:
"This product includes software developed by Computing Services at Carnegie Mellon University (http://www.cmu.edu/computing/)."
CARNEGIE MELLON UNIVERSITY DISCLAIMS ALL WARRANTIES WITH
REGARD TO THIS SOFTWARE, INCLUDING ALL IMPLIED WARRANTIES
OF MERCHANTABILITY AND FITNESS, IN NO EVENT SHALL CARNEGIE
MELLON UNIVERSITY BE LIABLE FOR ANY SPECIAL, INDIRECT OR CONSEQUENTIAL DAMAGES OR ANY DAMAGES WHATSOEVER RESULTING
FROM LOSS OF USE, DATA OR PROFITS, WHETHER IN AN ACTION OF
CONTRACT, NEGLIGENCE OR OTHER TORTIOUS ACTION, ARISING OUT
OF OR IN CONNECTION WITH THE USE OR PERFORMANCE OF THIS
SOFTWARE.
8
JupiterC2_GSG_EN_Pre_FM.book Page 9 Tuesday, December 28, 2004 1:39 PM
MD4
Copyright © 1990-2, RSA Data Security, Inc. All rights reserved.
License to copy and use this software is granted provided that it is identified as
the "RSA Data Security, Inc. MD4 Message-Digest Algorithm" in all material
mentioning or referencing this software or this function.
License is also granted to make and use derivative works provided that such
works are identified as "derived from the RSA Data Security, Inc. MD4 MessageDigest Algorithm" in all material mentioning or referencing the derived work.
RSA Data Security, Inc. makes no representations concerning either the merchantability of this software or the suitability of this software for any particular
purpose. It is provided "as is" without express or implied warranty of any kind.
These notices must be retained in any copies of any part of this documentation
and/or software.
MD5
Copyright © 1991-2, RSA Data Security, Inc. Created 1991. All rights reserved.
License to copy and use this software is granted provided that it is identified as
the "RSA Data Security, Inc. MD5 Message-Digest Algorithm" in all material
mentioning or referencing this software or this function.
License is also granted to make and use derivative works provided that such
works are identified as "derived from the RSA Data Security, Inc. MD5 MessageDigest Algorithm" in all material mentioning or referencing the derived work.
RSA Data Security, Inc. makes no representations concerning either the merchantability of this software or the suitability of this software for any particular
purpose. It is provided "as is" without express or implied warranty of any kind.
These notices must be retained in any copies of any part of this documentation
and/or software.
9
JupiterC2_GSG_EN_Pre_FM.book Page 10 Tuesday, December 28, 2004 1:39 PM
Samba(Ver 2.2.2-ja-1.1)
For SMB transmission, this machine uses Samba ver 2.2.2-ja-1.1 (hereinafter referred to as Samba 2.2.2-ja-1.1).
Copyright © Andrew Tridgell 1994-1998
This program is free software; you can redistribute it and/or modify it under the
terms of the GNU General Public License as published by the Free Software
Foundation; either version 2 of the License, or (at your option) any later version.
This program is distributed in the hope that it will be useful, but WITHOUT
ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public
License for more details.
You should have received a copy of the GNU General Public License along with
this program; if not, write to the Free Software Foundation, Inc., 675 Mass Ave,
Cambridge, MA 02139, USA
Note
❒ The source code for SMB transmission by this machine can be downloaded
from the following website:
http://support-download.com/services/scbs
RSA BSAFE®
• This product includes RSA BSAFE® cryptographic or security protocol software from RSA Security Inc.
• RSA and BSAFE are registered trademarks of RSA Security Inc. in the United
States and/or other countries.
• RSA Security Inc. All rights reserved.
10
JupiterC2_GSG_EN_Pre_FM.book Page 11 Tuesday, December 28, 2004 1:39 PM
How to Read This Manual
Symbols
This manual uses the following symbols:
R WARNING:
This symbol indicates a potentially hazardous situation that might result in
death or serious injury if you misuse the machine by not following the instructions under this symbol. Be sure to read the instructions, all of which are included in the Safety Information section in the General Settings Guide.
R CAUTION:
This symbol indicates a potentially hazardous situation that might result in minor or moderate injury or property damage not involving bodily injury, if you
misuse the machine by not following these instructions under this symbol. Be
sure to read the instructions, all of which are included in the Safety Information
section in the General Settings Guide.
* WARNINGS and CAUTIONS are notes for your safety.
Important
If these instructions are not followed, paper might be misfed, originals damaged, or data lost. Be sure to read these instructions.
Preparation
This symbol indicates the prior knowledge or preparation required before operation.
Note
This symbol indicates precautions for operation, or actions to be taken following
user error.
Limitation
This symbol indicates numerical limits, functions that cannot be used together,
or conditions under which a particular function cannot be used.
Reference
This symbol indicates where further relevant information can be found.
[
]
Keys that appear on the machine's display panel.
{
}
Keys built into the machine's control panel.
11
JupiterC2_GSG_EN_Pre_FM.book Page 12 Tuesday, December 28, 2004 1:39 PM
Safety Information
When using this machine, the following safety precautions should always be followed.
Safety During Operation
In this manual, the following important symbols are used:
R WARNING:
Indicates a potentially hazardous situation which, if instructions
are not followed, could result in death or serious injury.
R CAUTION:
Indicates a potentially hazardous situation which, if instructions are not
followed, may result in minor or moderate injury or damage to property.
R WARNING:
• Connect the power cord directly into a wall outlet and never use an extension cord.
• Disconnect the power plug (by pulling the plug, not the cable) if the
power cable or plug becomes frayed or otherwise damaged.
• To avoid hazardous electric shock or laser radiation exposure, do not
remove any covers or screws other than those specified in this manual.
• Turn off the power and disconnect the power plug (by pulling the plug,
not the cable) if any of the following occurs:
• You spill something into the machine.
• You suspect that your machine needs service or repair.
• The external housing of your machine has been damaged.
• Do not incinerate spilled toner or used toner. Toner dust might ignite
when exposed to an open flame.
• Disposal can take place at our authorized dealer.
• Dispose of the used toner bottle in accordance with the local regulations.
• Keep the machine away from flammable liquids, gases, and aerosols.
A fire or an electric shock might occur.
12
JupiterC2_GSG_EN_Pre_FM.book Page 13 Tuesday, December 28, 2004 1:39 PM
R CAUTION:
• Protect the machine from dampness or wet weather, such as rain and snow.
• Keep the machine away from humidity and dust. Otherwise a fire or an electric shock might occur.
• Do not place the machine on an unstable or tilted surface. If it topples over,
an injury might occur.
• If you use the machine in a confined space, make sure there is a continuous
air turnover.
• Unplug the power cord from the wall outlet before you move the machine.
While moving the machine, you should take care that the power cord will not
be damaged under the machine.
• When you disconnect the power plug from the wall outlet, always pull the
plug (not the cable).
• Do not allow paper clips, staples, or other small metallic objects to fall inside
the machine.
• Keep toner (used or unused) and toner bottle out of the reach of children.
• If toner or used toner is inhaled, gargle with plenty of water and move into a
fresh air environment. Consult a doctor if necessary.
• If toner or used toner gets into your eyes, flush immediately with large
amounts of water. Consult a doctor if necessary.
• If toner or used toner is swallowed, dilute by drinking a large amount of water. Consult a doctor if necessary.
• Avoid getting toner on your clothes or skin when removing a paper jam or
replacing toner. If your skin comes into contact with toner, wash the affected
area thoroughly with soap and water.
• If toner gets on your clothing, wash with cold water. Hot water will set the
toner into the fabric and may make removing the stain impossible.
• If your skin comes into contact with toner or used toner, wash the affected
area thoroughly with soap and water.
• For environmental reasons, do not dispose of the machine or expended
supply waste at household waste collection points. Disposal can take place
at an authorized dealer.
• The inside of the machine could be very hot. Do not touch the parts with a
label indicating “hot surface”. Otherwise, an injury might occur.
• The fusing section of this machine might be very hot. Caution should be taken when removing misfed paper.
• Do not use aluminum foil, carbon paper, or similar conductive paper to avoid
a fire or machine failure.
13
JupiterC2_GSG_EN_Pre_FM.book Page 14 Tuesday, December 28, 2004 1:39 PM
Positions of Labels and Hallmarks for
RWARNING and RCAUTION
This machine has labels for RWARNING and RCAUTION at the positions
shown below. For safety, please follow the instructions and handle the machine
as indicated.
ADL009S
14
JupiterC2_GSG_EN_Pre_FM.book Page 15 Tuesday, December 28, 2004 1:39 PM
ENERGY STAR Program
As an ENERGY STAR Partner, we have determined
that this machine model meets the ENERGY STAR
Guidelines for energy efficiency.
The ENERGY STAR Guidelines intend to establish an international energy-saving system for
developing and introducing energy-efficient office equipment to deal with environmental issues, such as global warming.
When a product meets the ENERGY STAR Guidelines for energy efficiency, the Partner shall
place the ENERGY STAR logo onto the machine model.
This product was designed to reduce the environmental impact associated with office equipment by means of energy-saving features, such as Low-power mode.
❖ Low-Power mode
• Low Power Mode
This product automatically lowers its power consumption 15 minutes after
the last copy or print job has finished. Printing is still possible in Low Power Mode, but if you wish to make copies press the {Energy Saver}
} key first.
Reference
For details about how to change the default interval, see p.61 “Energy
Saver Timer”.
• Sleep Mode
This product automatically lowers its power consumption even further 60
minutes after the last copy or print job has finished. This function is called
“Sleep Mode”. Printing from computer or fax is possible in this mode, but
if you wish to make copies, press the operation switch first.
Reference
For details about how to change the default interval, see p.61 “Auto Off
Timer”.
❖ Duplex Priority
The ENERGY STAR Program recommends the duplex function. By conserving paper resources this function reduces a burden to the environment. For
applicable machines, duplex function (one-sided originals→two-sided copies) is selected preferentially when the operation switch or the main power
switch is turned on, the {Energy Saver}
} key is pressed, or the machine resets
automatically.
Reference
To change the settings of the Duplex Priority mode, see “Duplex Mode Priority”in “General Features P.2/5”, Copy Reference.
15
JupiterC2_GSG_EN_Pre_FM.book Page 16 Tuesday, December 28, 2004 1:39 PM
Specifications
Type 1
Low - Power
mode
Sleep mode
Duplex Priority
Power consumption
Default interval
125W
Type 2
Type 3
130W
130W
15 minutes
Recovery Time
25 seconds
Power consumption
18W or less
Default interval
60 minutes
Recovery time
99 seconds
1 Sided→2 Sided
❖ Recycled Paper
In accordance with the ENERGY STAR Program, we recommend use of environmentally friendly recycled paper. Please contact your sales representative
for recommended paper.
16
JupiterC2_GSG_EN_Pre_FM.book Page 17 Tuesday, December 28, 2004 1:39 PM
Machine Types
This machine comes in three models which vary in copy speed. To confirm
which model you have, see the inside front cover.
Type 1
Type 2
Type 3
28 copies/minute
(A4K, 81/2" × 11"K)
35 copies/minute
(A4K, 81/2" × 11"K)
45 copies/minute
(A4K, 81/2" × 11"K)
Copy speed/Full Color 24 copies/minute
(A4K, 81/2" × 11"K)
28 copies/minute
(A4K, 81/2" × 11"K)
35 copies/minute
(A4K, 81/2" × 11"K)
Copy speed/B&W
17
JupiterC2_GSG_EN_Pre_FM.book Page 18 Tuesday, December 28, 2004 1:39 PM
18
JupiterC2_GSG_EN_Pre_FM.book Page 19 Tuesday, December 28, 2004 1:39 PM
1. Getting Started
Guide to Components
AFZ029S
1. Exposure glass cover (optional) or
Auto Document Feeder (ADF) (optional)
5. Earth Leakage Breaker
Lower the exposure glass cover over
originals placed on the exposure glass. If
you have the ADF, load a stack of originals here. They will be fed automatically,
one by one.
(The illustration shows the ADF.)
6. Ventilation holes
2. Exposure glass
Place originals face down.
3. External tray
Copied, printed paper or fax messages
are delivered here.
4. Duplex reversal unit
Open this to remove misfed paper. The
upper left cover can be opened by first
opening the duplex reversal unit.
Prevents electric shock. See p.152 “Earth
Leakage Breaker”.
Prevents overheating. Do not obstruct
the ventilation holes by placing anything
near it or leaning objects against it. If the
machine overheats, an error might occur.
7. Main power switch
If the machine does not operate after
turning on the operation switch, check
the main power switch is turned on. If it
is off, turn it on.
8. Operation switch
Press this switch to turn the power on
(the On indicator lights up). To turn the
power off, press this switch again (the On
indicator goes off).
19
JupiterC2_GSG_EN_Pre_FM.book Page 20 Tuesday, December 28, 2004 1:39 PM
Getting Started
9. Control panel
12. Paper tray
See p.23 “Control Panel”.
Load paper here. See p.113 “BLoading
Paper”.
10. Standard tray
Copied, printed paper or fax messages
are delivered here.
1
11. Front cover
13. Paper tray unit (optional)
Load paper here. See p.113 “BLoading
Paper”, p.21 “External Options”.
Open to access the inside of the machine.
AFZ024S
1. Upper right cover
4. Bypass tray extension
Open this cover to replace the toner cartridge.
Pull out this extension to load paper in
the bypass tray when its length is longer
than that of A4Lsize.
2. Ventilation holes
20
Prevent overheating. Do not obstruct the
ventilation holes by placing an object
near it or leaning things against it. If the
machine overheats, a fault might occur.
5. Bypass tray
3. Optional connectors
6. Lower right cover
Use to connect options such as Bluetooth.
Open this cover to remove misfed paper.
Use to print on thick paper, OHP transparencies, custom size paper, as well as
plain paper.
JupiterC2_GSG_EN_Pre_FM.book Page 21 Tuesday, December 28, 2004 1:39 PM
Guide to Components
External Options
1
AFZ006S
1. Left tray
5. 2 Tray finisher
If you select this as the output tray, copies
will be delivered face down.
Sorts, stacks, staples, and punches copies.
*1 Finisher Shift Tray 1
*2 Finisher Shift Tray 2
2. Exposure glass cover
Lower this cover over originals before
copying.
6. Booklet finisher
Load a stack of originals here. They will
be fed in automatically.
Sorts, stacks, and staples copies. The saddle stitch function can staple the copies in
the center and folds them like a booklet.
*3 Finisher Shift Tray
4. Scanner Accessibility Unit
7. 1 Tray paper unit
This unit lets you operate the machine or
scan documents from the side instead of
using the control panel on the machine.
Consists of 1 paper tray.
3. ADF
Note
❒ When the scanner accessibility unit is
installed, the control panel and the
scanner unit on the machine cannot be
used.
8. 2 Tray paper unit
Consists of 2 paper trays.
9. Large Capacity Tray (LCT)
Holds up to 2000 sheets of A4Kpaper.
21
JupiterC2_GSG_EN_Pre_FM.book Page 22 Tuesday, December 28, 2004 1:39 PM
Getting Started
Internal Options
A
1
B
C
D
E
F
G
*1
22
Fax unit
Allows you to use the facsimile function.
IEEE 1394 interface board *1
Connects to an IEEE 1394 cable.
Bluetooth *1
Allows you to expand the interface.
File Format Converter
Allows you to download documents from the Document Server stored by
copier and printer functions. See p.48 “Downloading Stored Documents”.
IEEE 802.11b Wireless LAN Board *1
You can install a wireless LAN interface.
IEEE 1284 Interface Board *1
Connects to an IEEE 1284 cable.
DataOverwriteSecurity Unit
Allows you to erase data on the hard disk.
You cannot install two or more of the options below:
IEEE 1394 interface board, IEEE 802.11b Wireless LAN Board, IEEE 1284 Interface
Board, Bluetooth.
JupiterC2_GSG_EN_Pre_FM.book Page 23 Tuesday, December 28, 2004 1:39 PM
Control Panel
Control Panel
This illustration shows the control panel of a machine with options fully installed.
1
AAE036S
1. Screen contrast knob
Adjusts display panel brightness.
2. {User Tools/Counter}} key
• User Tools
Press to change defaults and conditions to meet your requirements. See
p.54 “Accessing User Tools (System
Settings)”.
• Counter
Press to check or print the counter value. See p.158 “Counter”.
• Inquiry
Press to find out where to order expendable supplies and where to call
when a malfunction occurs. You can
also print these details. See p.156 “Inquiry”
3. Indicators
Display the status of the machine or indicate errors.
• d: Add Staple indicator. See p.131
“dAdding Staples”.
• D: Add Toner indicator. See p.116
“DAdding Toner”.
• B: Load Paper indicator. See p.113
“BLoading Paper”.
• L: Service Call indicator
• M: Open Cover indicator
• x: Misfeed indicator. See p.119
“xClearing Misfeeds”.
• Communicating: Communicating indicator. See “Control Panel”, Facsimile
Reference <Basic Features>.
• i: Confidential File indicator. See
“Control Panel”, Facsimile Reference
<Basic Features>.
• Receive File: Receiving File indicator.
See “Control Panel”, Facsimile Reference <Basic Features>.
4. {Adjust/Program Color}} key (copy
mode)
Use this key to adjust and register colors.
See “Color Adjustment”, “User Color”,
Copy Reference.
Note
❒ When image quality is adjusted, the
lamp in the {Adjust/Program Color}
} key
is lit.
5. Color circle
Refer to this when adjusting colors. See
“Color Adjustment”, Copy Reference.
6. Display panel
Displays operation status, error messages, and function menus. See p.25 “Display Panel”.
7. {Check Modes}} key
Press to check the entered copy job settings.
23
JupiterC2_GSG_EN_Pre_FM.book Page 24 Tuesday, December 28, 2004 1:39 PM
Getting Started
1
8. { Program}} key (copier/facsimile/scanner mode)
17. {#}} key
Press to register frequently used settings,
or recall registered settings.
18. Number keys
9. {Clear Modes}} key
Press to clear previous copy job settings.
10. {Energy Saver}} key
Press to switch into and out of Energy
Saver mode. See p.30 “Energy Saver
Mode”.
11. {Interrupt}} key (copier mode)
Press to make interrupt copies during
copying or scanning. See “Interrupt
Copy”, Copy Reference.
12. Main power indicator and On
indicator
The main power indicator turns on when
you turn on the main power. The On indicator lights when the power is on.
Important
❒ Do not turn off the main power
switch while the On indicator is
turning on or is flashing. The hard
disk may malfunction.
13. Operation switch
Press to turn the power on (the On indicator goes on). To turn the power off,
press again (the On indicator goes off).
See p.28 “Turning On the Power”.
14. {Sample Copy}} key
Press to make a single set of copies or
prints to check print quality before making multiple sets. See “Sample Copy”
Copy Reference.
15. {Start}} key
Press to start copying. Press to start scanning or printing documents stored using
the Document Server function.
16. {Clear/Stop}} key
• Clear
Press to delete a number entered.
• Stop
Press to stop a job in progress.
24
Press to enter a numerical value.
Press to enter the number of copies and
data for a selected function.
19. {Start Manual RX}} key, {On Hook Dial}
} key, { Pause/Redial}
} key, and
{Tone}
} key
Reference
Facsimile Reference <Basic Features>
and Facsimile Reference <Advanced
Features>
20. Color Selection keys (copy
mode)
Switch keys depending on the type of
original, or the copying purpose:
{Auto Color Selection}
}:
{Full Color}
}:
{Black & White}
}:
{Single Color}
}:
{Two-color}
}:
See “Color Functions”, Copy Reference.
21. Function keys
Press to select one of the following functions:
• Copy:
• Document Server:
• Facsimile:
• Printer:
• Scanner:
22. Function status indicators.
Display the status of the above functions:
• Green: active.
• Red: interrupted.
23. mindicator
The data indicator shows the status of
data reception. See “Control Panel”,
Printer Reference.
JupiterC2_GSG_EN_Pre_FM.book Page 25 Tuesday, December 28, 2004 1:39 PM
Control Panel
Display Panel
The display panel shows machine status, error messages, and function menus.
The function items displayed serve as selector keys You can select or specify an
item by lightly pressing them.
When you select or specify an item on the display panel, it is highlighted thus
. Keys appearing as
cannot be used.
1
Important
❒ A force or impact of more than 30 N (about 3 kgf) will damage the display
panel.
The copying screen is displayed as default after power on.
The following display shows a machine with options fully installed.
Common key operations
The following keys are common to all screens:
❖ Key list
[OK]
Acknowledges a selected function or entered values, and then returns
to the previous display.
[Cancel]
Deletes a selected function or entered values, and then returns to the
previous display.
[U
UPrev.] [T
TNext]
Moves to the previous or next display when all items cannot be shown
on the same display.
[OK] [Yes]
Closes displayed messages.
[Clear]
Cancels entered values but does not change the settings.
[Exit]
Returns to the previous display.
25
JupiterC2_GSG_EN_Pre_FM.book Page 26 Tuesday, December 28, 2004 1:39 PM
Getting Started
When the Authentication Screen is displayed
When Basic Authentication, Windows Authentication, or LDAP Authentication
is set, the authentication screen is displayed. Unless a valid user name and password are entered, operations are not possible with the machine.
1
Note
❒ Consult the User Administrator about your login user name and login password. For details of the various types of user authentication, consult the respective administrators.
❒ When User Code Authentication is set, the screen for entering a user code is
displayed instead. For details, see p.75 “Authentication Information”.
A Press [Enter] for Login User Name.
B Enter a login user name, and then press [OK].
C Press [Enter] for Login Password.
D Enter a login password, and then press [OK].
E Press [Login].
When the user is authenticated, the screen for the function you are using appears.
Note
❒ When the entered login user name or login password is not correct, "Authentication has failed." appears. Check the login user name and password.
26
JupiterC2_GSG_EN_Pre_FM.book Page 27 Tuesday, December 28, 2004 1:39 PM
Control Panel
Log Off
Important
❒ To prevent unauthorized users from using the machine, always log off when
you have finished using the machine.
1
A Press {User Tools / Counter}}.
B Press [Logout].
C Press [Yes].
D Press {User Tools / Counter}}.
27
JupiterC2_GSG_EN_Pre_FM.book Page 28 Tuesday, December 28, 2004 1:39 PM
Getting Started
Turning On the Power
This machine has two power switches.
1
The main power indicator turns
on.
❖ Operation switch (right side of the
control panel)
Press to activate the machine.
When the machine has finished
warming up, you can make copies.
❖ Main power switch (left side of the machine)
Turning off this switch will turn
off the main power indicator on
the right side of the control panel.
After this is done, machine power
is completely off.
When the fax unit (optional) is installed, fax files in memory may be
lost if you turn this switch off. Use
this switch only when necessary.
Note
❒ This machine automatically enters
Energy Saver mode or turns itself
off if you do not use it for a while.
See p.61 “Auto Off Timer”, “Energy Saver Timer”.
AFZ002S
Important
❒ Do not turn off the main power
switch immediately after turning it on. Doing so may result in
damage to the hard disk or
memory, leading to malfunction.
Turning On the Power
A Press the operation switch.
The On indicator turns on.
Turning On the Main Power
A Make sure that the power cord is
firmly plugged into the wall outlet.
B Open the switch cover, and then
turn on the main power switch.
28
Note
❒ If the power does not turn on
when the operation switch is
pressed, check the main power
switch is on. If it is off, turn it on.
JupiterC2_GSG_EN_Pre_FM.book Page 29 Tuesday, December 28, 2004 1:39 PM
Turning On the Power
Turning Off the Power
A Make sure the On indicator is not
A Make sure the exposure glass cov-
B Open the switch cover, and then
er or the ADF is in the right position.
B Press the operation switch.
lit.
1
turn off the main power switch.
The main power indicator turns
off.
The On indicator turns off.
-When the fax unit (optional) is
installed
Note
❒ Even if you press the operation
switch, and the indicator does
not turn off, it will blink in the
following cases:
• When the exposure glass cover or ADF is open.
• During communication with
external equipment.
• When the hard disk is active.
Turning Off the Main Power
Important
❒ Do not turn off the main power
switch when the On indicator is lit
or blinking. Doing so may result in
damage to the hard disk or memory.
❒ Be sure to turn off the main power
switch before pulling out the power plug. Not doing this may result
in damage to the hard disk or
memory.
When the main power switch is
turned off while using the facsimile
function, waiting fax and print jobs
may be canceled, and incoming fax
documents not received. If you have
to turn off this switch for some reason, follow the procedure below.
Important
❒ Make sure 100% is shown as available memory on the display before
turning off the main power switch
or unplugging the power cord. Fax
files in memory are deleted an
hour after you turn off the main
power switch or unplug the power
cord. See ”Power Failure Report”,
Facsimile Reference <Advanced Features>.
❒ The On indicator will not turn off,
but will blink in dial-in mode even
if you press the operation switch.
When this happens, check the explanations below, and turn off the
main power switch.
• The computer is not controlling
the machine.
• The machine is not receiving a
fax.
29
JupiterC2_GSG_EN_Pre_FM.book Page 30 Tuesday, December 28, 2004 1:39 PM
Getting Started
Saving Energy
1
- Energy Saver Mode
If you do not use the machine for a
certain period after an operation, or
when you press the { Energy Saver}
}
key, the display disappears and the
machine goes into Energy Saver
mode. When you press the {Energy
Saver}
} key again, the machine returns
to the ready condition. The machine
uses less electricity in Energy Saver
mode.
Note
❒ You can change the amount of time
the machine waits before switching to Energy Saver mode after
copying has finished or the last operation is performed. See p.61 “Energy Saver Timer”.
30
-Auto Off
The machine automatically turns itself off when the job is finished, after
a certain period of time has elapsed.
This function is called “Auto Off”.
Note
❒ You can change the Auto Off time.
See p.61 “Auto Off Timer”.
❒ The Auto Off Timer function will
not operate in the following cases:
• When a warning message appears
• When the service call message
appears
• When paper is jammed
• When the cover is open
• When the “Add Toner" message
appears
• When toner is being replenished
• When the User Tools/Counter
screen is displayed
• When fixed warm-up is in progress
• When the facsimile, printer or
other functions are active
• When operations were suspended during printing
• When the handset is in use
• When the On-hook dialing function is in use
• When a recipient is being registered in the address list or
group dial list
• When the Data In indicator is on
or blinking
• When the sample print or locked
print screen is displayed
JupiterC2_GSG_EN_Pre_FM.book Page 31 Tuesday, December 28, 2004 1:39 PM
2. Combined Function
Operations
Changing Modes
Note
❒ You cannot switch modes in any of the following situations:
• When scanning in a fax message for transmission
• During immediate transmission
• When accessing User Tools
• During interrupt copying
• During On hook dialing for fax transmission
• While scanning an original
31
JupiterC2_GSG_EN_Pre_FM.book Page 32 Tuesday, December 28, 2004 1:39 PM
Combined Function Operations
❒ The copying screen is displayed as default after power on. You can change
this default setting. See p.55 “Function Priority”.
2
AFZ040S
- System Reset
The machine returns automatically to its initial condition when the job is finished, after a certain period of time has elapsed. This function is called “System
Reset”. See p.55 “Function Priority”.
Note
❒ You can change the System Reset time. See p.61 “System Auto Reset Timer”.
32
JupiterC2_GSG_EN_Pre_FM.book Page 33 Tuesday, December 28, 2004 1:39 PM
Multi-Access
Multi-Access
You can carry out another job using a different function while the current job is
being performed. Performing multiple functions simultaneously in this manner
is called “Multi-accessing”.
This allows you to handle jobs efficiently, regardless of how the machine is being
used. For example:
• While making copies, you can scan documents to store in the Document Server.
• While printing documents stored in the Document Server, the machine can
receive print data.
• You can make copies while receiving fax data.
• While printing print data, you can make operations for copying.
2
Note
❒ See p.55 “Print Priority” for setting function priority. As default, [Display
Mode] is set to first priority.
❒ When the 2 tray finisher or booklet finisher is installed on the machine, you
can specify the output tray where documents are delivered. For details about
how to specify the output tray for each function, see the following descriptions:
• p.56 “Output: Copier (copier)”
• p.57 “Output: Document Server (Document Server)”
• p.57 “Output: Facsimile (facsimile)”
• p.57 “Output: Printer (printer)”
- Function Compatibility
The chart shows Function Compatibility when print priority is set to “Interleave”. See p.55 “Print Priority”.
|: Simultaneous operations are possible.
$: Operation is enabled when the relevant function key is pressed and remote
switching (of the scanner/external extension) is done.
❍: Operation is enabled when the {Interrupt}
} key is pressed to interrupt the preceding operation.
→: Operation is performed automatically once the preceding operation ends.
×: The operation must be started once the preceding operation ends. (Simultaneous operations are not possible.)
33
JupiterC2_GSG_EN_Pre_FM.book Page 34 Tuesday, December 28, 2004 1:39 PM
*5
Printing from Document Server
Printing from Document Server
DeskTopBinder
Document Server
Scanning a Document to Store in Document Server
Operations for Document Server
Scanner
Scanning
Operations for Scanning
Print
Stapling
Printing
Data Reception
Printing Received Data
Memory Reception
Immediate Transmission
Reception
Transmission
Memory Transmission
*2
*2
*2
*2 *4 *4
*4
| → → ❍ ❍ $$| $| | | | | $$$$| | | |
*2
*2
*2
*2
❍❍ ❍ × × × × | × | | | | | × × × × × | | |
❍ ❍ ❍ × × × × | × | →| →→× × × × × →| →
× | | | | | $$$$$| | |
Transmission Opera- $ $ $ ❍ ❍ × × |
tion/Manual Reception Operation
Scanning an origi- × × × × × × × |
nal for Memory
Transmission
Memory Transmis- | | | | | | | |
sion
*3
Transmission
Facsimile
Operations for
Copying
Copying
Scanning an Original for Memory Transmission
| → → ❍ ❍ $$| $| | | | → $$$$| | | |
*1 *1 *1
Interrupt Copying
Printer
× × × ❍ ❍ $$| $| | | | | $$$$$| | |
*1 *1 *1
Sort
Copying
Sort
Operations for Copying
Stapling
Mode before you select
Copy
Operations for
Copying
Stapling
Operations for Copying
2
Transmission Operation/Manual Reception Operation
Facsimile
Interrupt Copying
Mode after you select Copy
Sending a Facsimile from Document Server Professional/Lite
Printing
Web Document Server
Combined Function Operations
× | | | | | × × × × × | | |
| | | | | | | | | | | | →|
*3 *3 *7
Immediate Trans- × × × × × × × | × | | | | | × × × × × | → |
mission
*3
*3
Reception
Memory Reception | | | | | | | | | | | | | | | | | | | | | |
Printer
*3 *3 *3 *7
Printing Received | | | | | | | | | | × | | | | | | | | | | |
Data
*7
*7
Data Reception
Print
Printing
Scanner
34
Stapling
| | | | | | | | | | | →→→| | | | | | | |
| | | ❍ ❍ | | | | | | | →→| | | | | | | |
| →| ❍ ❍ | | | | | | | →→| | | | | | | |
*5
Operations for
scanning
Scanning
*4 *4
*4
$$$❍ ❍ $$| $| | | | | × × $$$| | |
× × × × × × × | × | | | | | × × × × | | | |
JupiterC2_GSG_EN_Pre_FM.book Page 35 Tuesday, December 28, 2004 1:39 PM
DeskTopBinder
Printing from Document Server
Mode before you select
Document Server Operations for
$$$❍ ❍ $$| $| | | | | $$× ×
Document Server
Scanning a Docu- $ × × ❍ ❍ $ × | × | | | | | $ × × ×
ment to Store in
Document Server
Printing from Doc- $ | | ❍ ❍ | | | | | | | | | | | | |
ument Server
*4
*4
*6 *6
Printing from Document Server
Scanning a Document to Store in Document Server
Operations for Document Server
Scanner
Scanning
Operations for Scanning
Stapling
Printing
Data Reception
Print
Reception
Printing Received Data
Memory Reception
Immediate Transmission
Document Server
Printer
Transmission
Memory Transmission
Scanning an Original for Memory Transmission
Copying
Sort
Operations for Copying
Stapling
Operations for Copying
Transmission Operation/Manual Reception Operation
Facsimile
Interrupt Copying
Mode after you select Copy
Sending a Facsimile from Document Server Professional/Lite
Printing
Web Document Server
Multi-Access
2
× | | |
× | | |
| | | |
*6
DeskTopBinder Printing from Doc- | | | | | | | | | | | | | | | | | | | → | |
Professional/Lite ument Server
*4
Web Document
Server
*1
*2
*3
*4
*5
*6
*7
Sending a Facsimi- | | | | | | | | | | | | | | | | | | | | → |
le from Document
Server
Printing
| | | | | | | | | | | | | | | | | | | | | →
*4
Simultaneous operations are only possible after the preceding job documents are all
scanned and the [NextJob] key appears.
You can scan a document after the preceding job documents are all scanned.
Operation is possible when extra lines are added.
During stapling, printing automatically starts after the current job.
Stapling is not available.
Simultaneous operation become possible after you press the [NextJob] key.
During parallel reception, any subsequent job is suspended until the receptions are
completed.
Limitation
❒ Stapling cannot be used at the same time for multiple functions.
❒ While printing is in progress, scanning using another function may require
more time than usual.
35
JupiterC2_GSG_EN_Pre_FM.book Page 36 Tuesday, December 28, 2004 1:39 PM
Combined Function Operations
2
36
JupiterC2_GSG_EN_Pre_FM.book Page 37 Tuesday, December 28, 2004 1:39 PM
3. Document Server
Relationship between Document Server
and Other Functions
The following table describes the relationship between the Document Server
and other functions.
function
Where to store
documents
Displaying a list
Printing stored
documents
Sending
documents
Copy
Copy/Document Server
Available
Available
Not Available
Printer
Document Server Available
Available
Not Available
Facsimile
Facsimile
Available
Available
Available *1
Scanner
Scanner
Not Available *2
Not Available
Available *3
*1
*2
*3
You can send stored documents using the facsimile function. See “Sending a Stored
File”, Facsimile Reference <Advanced Features>.
You can display stored documents using the scanner function. See “Displaying the
List of Stored Files”, Scanner Reference.
You can send stored documents using the scanner function. See “Sending Stored
Files by E-mail or Scan to Folder, or Delivering”, Scanner Reference.
Note
❒ The following table shows the capacity of the Document Server.
Number of pages for
each file
Number of files
Number of pages in
total
1,000 pages
2,000 files
9,000 pages
Copy
Printer
Scanner
Facsimile
37
JupiterC2_GSG_EN_Pre_FM.book Page 38 Tuesday, December 28, 2004 1:39 PM
Document Server
Document Server Display
❖ Document Server Main Display
3
AFZ021S
1. Operating status and messages.
2. The title of the currently selected
4. The operation keys
5. The functions under which the
screen.
documents were stored.
3. The numbers of originals, copies,
and printed pages.
The icons below show the functions active when the documents were stored
in the Document Server.
Function
Copier
Facsimile
Printer
Icon
Note
❒ Depending on the settings of security functions, not all the stored documents may be displayed.
38
JupiterC2_GSG_EN_Pre_FM.book Page 39 Tuesday, December 28, 2004 1:39 PM
Using the Document Server
Using the Document Server
Storing Data
❖ File name
Stored documents are automatically
named “COPY0001”, “COPY0002”.
You can change assigned file
names.
❖ User name
You can register a user name to
identify the user or user group that
stored the documents. To assign it,
you can register the user name using the name assigned to the user
code, or by entering the name directly.
Reference
For details about the user name,
see p.73 “Registering Names”.
❖ Password
You can set a password for stored
documents, and use it to prevent
others printing them. When a password is set for the documents,
appears next to the documents.
Reference
To store documents without using
Document Server function, see the
manuals for those modes.
Important
❒ Data stored in the machine might
be lost if some kind of failure occurs. The manufacture shall not be
responsible for any damage resulting from loss of data.
❒ Be careful not to let anyone know
your password, especially when
entering a password or recording
it. Keep any record of your password in a secure place.
❒ Avoid using a single number or
consecutive numbers for a password such as “0000” or “1234”,
since the numbers like this are easy
to guess, so using them will not
provide a worthwhile level of security.
❒ A document accessed with a correct password remains selected
even after operations are complete,
and it can be accessed by other users. To stop this, be sure to press
the {Clear Modes}
} key to cancel the
document selection.
❒ The user name used when adding
a document to the Document Server is to identify the document creator and type. It is not to protect
confidential documents from others.
3
Note
❒ By default, data stored in the Document Server is deleted after three
days (72 hours). You can specify
the time taken for the stored data
to be deleted automatically. See
p.68 “Auto Delete File”.
❒ If you do not want stored data to
be automatically deleted, select
[No] in Auto Delete File before storing a document. If you select [Yes]
later, data stored afterward will be
automatically deleted.
❒ When the machine is printing a
document stored using the copier
function, wait until printing has
finished before you store a document in the Document Server.
39
JupiterC2_GSG_EN_Pre_FM.book Page 40 Tuesday, December 28, 2004 1:39 PM
Document Server
A Press the {Document Server}} key.
E Make any required settings.
Reference
For details, see Copy Reference.
3
ZGJS776N
B Press [Scan Original].
C Enter a user name, file name, or
password if necessary.
Note
❒ If you do not enter a file name,
one is automatically assigned.
Reference
p.40 “To register or change a
user name”
p.41 “To change a file name”
p.42 “To set or change a password”
D Place originals either on the exposure glass or in the ADF.
Reference
For information about types of
originals and how to place
them, see “Placing Originals”
Copy Reference.
40
F Press the {Start}} key.
The document is stored in the Document Server.
Note
❒ To stop scanning, press the
{ Clear/Stop}
} key. To restart a
paused scanning job, press [Continue] in the confirmation display. To delete saved images
and cancel the job, press the
[Stop] key.
❒ When a password is set, appears on the left side of the file
name.
❒ If you placed originals on the
exposure glass, press [Scanning
Finished] after all the originals
have been scanned. The Select
Files to Print display appears.
To register or change a user name
A Press [Scan Original].
The Scan Original display appears.
B Press [User Name].
If user names are already registered,
the Change User Name display appears. To use an unregistered user
name, press [Non-programmed Name].
JupiterC2_GSG_EN_Pre_FM.book Page 41 Tuesday, December 28, 2004 1:39 PM
Using the Document Server
When no user names are registered
in the Address Book, the User
(Destination) Name entry display
appears.
Reference
p.75 “Authentication Information”
When no user names are
registered in the Address Book
A Enter a new user name, and
then press [OK].
When using a registered user
name in the Address Book
A Select a registered user name
from the list, and then press
[OK].
3
Reference
p.159 “Entering Text”
To change a file name
A Press [Scan Original].
The Scan Original display appears.
To change your user name to an
unregistered user name, proceed to the next step.
B Press [File Name].
Reference
p.75 “Registering a New
User Code”
When using an unregistered user
name in the Address Book
A To enter an unregistered user
name, press [Non-programmed
Name].
B Enter a new user name, and
then press [OK].
Reference
p.159 “Entering Text”
The Change File Name display appears.
C Press [Delete All] to delete the old
file name.
Note
❒ You can also use [Backspace] to
delete unnecessary characters.
D Enter a new file name, and then
press [OK].
Note
❒ Up to 20 characters can be entered as a file name. Note that
only 16 characters of each file
name appear in the document
list.
Reference
p.159 “Entering Text”
41
JupiterC2_GSG_EN_Pre_FM.book Page 42 Tuesday, December 28, 2004 1:39 PM
Document Server
To set or change a password
C Press [File Management].
A Press [Scan Original].
The Scan Original display appears.
B Press [Password].
D Press [Change User Name], [Change
File Name], or [Change Password].
E Enter
3
C Enter a password using the num-
the new user name, file
name, or password using the letter keys or number keys and then
press [OK].
D Reenter the password (four dig-
Reference
p.40 “To register or change a
user name”
E Press [OK].
p.41 “To change a file name”
p.42 “To set or change a password”
ber keys (four digits), and then
press the {#}
} key.
its) for verification, and then
press the {#}
} key.
Changing a Stored
Document's File Name, User
Name, or Password
A Press the {Document Server}} key.
B Select the document with the user
F Press [OK].
Selecting a Document
A Press the {Document Server}} key.
B Select a document you want to
print.
name, file name, or password you
want to change.
Note
❒ If a password is already set for
the document, enter that password, and then press [OK].
42
Note
❒ If a password is already set for
the document, enter that password, and then press [OK].
❒ You can search for the document using [Search by User Name]
or [Search by File Name] at the left
top of the display. See p.43
“Searching for Stored Documents”.
JupiterC2_GSG_EN_Pre_FM.book Page 43 Tuesday, December 28, 2004 1:39 PM
Using the Document Server
❒ You can sort document names
in the list by user name, file
name, or date. To sort documents, press [User Name], [File
Name], or [Date].
❒ If you cannot determine docum ent c on ten t from t he file
name, you can print just the first
page of the document for checking purposes. See p.46 “Printing
the first page”.
❒ To cancel document selection,
press it again.
C To print multiple documents, repeat step B in the order you want
to print.
Note
❒ You can select up to 30 documents.
❒ If the sizes or resolution of selected documents are not the
same, it may not be possible to
print them.
❒ If you want to change the printing order, cancel the selection,
and select documents again,
this time in the order you want.
❒ If you press the {Clear Modes}
}
key, selection of all documents
will be canceled.
❒ If you press [Printg Odr], the documents in print order.
To check the details of stored documents
A Select a document to display its
detailed information.
Note
❒ If a password is already set for
the document, enter that password, and then press [OK].
B Press [Detail].
3
Detailed information about the
document appears.
Note
❒ If you selected several documents, use [U
U] and [T
T] to view
the details of each.
❒ Press [OK]. The Select Files to
Print display reappears.
Searching for Stored
Documents
You can use either [Search by File
Name] or [Search by User Name] to
search for documents stored in the
Document Server. You can also list
stored documents in a preferred order.
Note
❒ If you install DeskTopBinder Professional or DeskTopBinder Lite
on your computer, you can search
for and rearrange documents using your computer.
Reference
Manuals for DeskTopBinder Professional/Lite or Help
43
JupiterC2_GSG_EN_Pre_FM.book Page 44 Tuesday, December 28, 2004 1:39 PM
Document Server
To search by file name
A Press the {Document Server}} key.
B Press [Search by File Name].
3
C Enter the file name using the letter keys, and then press [OK].
Only files beginning with the
name entered appear in the Select
Files to Print display.
Reference
p.159 “Entering Text”.
Note
❒ To display all files stored in the
Document Server, press [File
List].
To search by user name
A Press the {Document Server}} key.
B Press [Search by User Name].
D To
specify an unregistered user
name, press [Non-programmed
Name]. Enter a user name, and
then press [OK].
Reference
p.159 “Entering Text”
E Press [OK].
Only files beginning with the
name entered appear in the Select
Files to Print display.
Note
❒ To display all files stored in the
Document Server, press [File
List].
Printing Stored Documents
Note
❒ You can print stored documents
from a network computer using a
Web browser. For details about
how to start the Web browser, see
“Using Web Image Monitor”, Network Guide.
A Select
a document you want to
print.
C To specify a registered user name,
select the user name from the displayed list, and then press [OK].
Note
❒ To specify an unregistered user
name, follow the procedure below.
44
Note
❒ If a password is already set for
the document, enter that password, and then press [OK].
❒ You can print multiple documents. See p.42 “Selecting a
Document”.
JupiterC2_GSG_EN_Pre_FM.book Page 45 Tuesday, December 28, 2004 1:39 PM
Using the Document Server
B If you need to change print settings, press [Print Settings].
The Print Settings display appears.
User names, file names, and print
order of documents appear.
Note
❒ Print settings made for printing
in copier or printer function remain after printing and applied
to the next job. Print settings
made in facsimile mode, however, do not remain.
❒ If you select multiple documents, the print settings will remain applied to the first
document, but not to other documents.
❒ Print setting items are listed below. For details about print results of each setting, see Copy
Reference.
❖ Binding format
• 2 Sided Copy Top to Top
• 2 Sided Copy Top to Bottom
• Magazine
• Book
❖ Cover handling
• Cover/Slip Sheet
• Edit/Stamp
❖ Finish
• Sort
• Rotate Sort
• Stack
• Staple
• Punch
❒ If you print more than one set
using the Sort function, you can
check the print result by printing out only the first set. See
p.46 “Sample copy”.
❒ When multiple documents are
printed at the same time, you
can combine them into a single
set by adjusting the print order.
❒ When multiple documents are
printed at the same time, print
settings made for the document
printed first are applied to all
other documents.
❒ If you select multiple files, you
can check file names or print order selected in step A by scrolling the list using [T
T] and [U
U].
❒ Press [Select File] to return to the
Select Files to Print display.
❒ The preset stamp function is not
available for documents stored
in facsimile mode.
3
C Enter
the required number of
prints using the number keys
Note
❒ Up to 999 can be entered.
D Press the {Start}} key.
Printing starts.
To stop printing
A Press the {Clear/Stop}} key.
B Press [Stop].
45
JupiterC2_GSG_EN_Pre_FM.book Page 46 Tuesday, December 28, 2004 1:39 PM
Document Server
Changing the number of copies
during printing
Limitation
❒ The number of copies can only be
changed when the Sort function is
selected in the print settings.
A Press the {Clear/Stop}} key.
B Press [Change Quantity].
C Enter a new number of copies us-
3
ing the number key.
D Press the {#}} key.
E Press [Continue].
Printing restarts.
Sample copy
If you print multiple sets using the
Sort function, you can check the print
order or print settings are correct by
printing only the first set using the
{Sample Copy}
} key.
Limitation
❒ This function can only be used
when the Sort function is selected.
A Select the document.
Note
❒ If a password is already set for
the document, enter that password, and then press [OK].
46
❒ You can search for the document by using [Search by User
Name] or [Search by File Name] at
the left top of the display. See
p.43 “Searching for Stored Documents”.
❒ You can sort document names
in the list by user name, file
name, or date. To sort documents, press [User Name], [File
Name], or [Date].
❒ To cancel a document selection,
press it again.
B Press the {Sample Copy}} key.
The first set prints out.
C If the sample is acceptable, press
[Print].
Note
❒ Press [Suspend] to cancel printing and return to the Print Settings menu to change settings.
Printing the first page
You can print the first page of the document selected in the Select Files to
Print display to check its content.
If more than one document selected,
the first page of each is printed.
A Select the document.
Note
❒ If a password is already set for
the document, enter that password, and then press [OK].
❒ You can search for the document by using [Search by User
Name] or [Search by File Name] at
the left top of the display. See
p.43 “Searching for Stored Documents”.
JupiterC2_GSG_EN_Pre_FM.book Page 47 Tuesday, December 28, 2004 1:39 PM
Using the Document Server
❒ You can sort document names
in the list by user name, file
name, or date. To sort documents, press [User Name], [File
Name], or [Date].
❒ To cancel a document selection,
press it again.
B Press [Print 1st Page].
C Press the {Start}} key.
Deleting Stored Documents
Important
❒ You can store up to 2,000 documents in the Document Server. No
more documents can be stored
when the total is 2,000. You should
delete unnecessary documents to
increase available memory.
Note
❒ You can delete all stored documents at once with User Tools. See
p.68 “Delete All Files”.
❒ You can delete stored documents
from a network computer using
the Web browser. For details about
how to start the Web browser, see
“Using Web Image Monitor”, Network Guide.
A Press the {Document Server}} key.
B Select the document to delete.
Note
❒ If a password is already set for
the document, enter that password, and then press [OK].
❒ You can delete multiple documents at once. See p.42 “Selecting a Document”.
❒ You can search for a document
by using [Search by User Name] or
[Search by File Name] at the left
top of the display. See p.43
“Searching for Stored Documents”.
❒ You can sort document names
in the list by the user name, file
name, or date. To sort documents, press [User Name], [File
Name], or [Date].
❒ If you cannot find the document
by name, you can print the first
page of a document to check its
contents. See p.46 “Printing the
first page”.
❒ Press the selected line again to
cancel the print job.
3
C Press [Delete File].
D Press [Delete] to delete the document.
Viewing Stored Documents
Using a Web Browser
Reference
The Web browser's Help
A Start a Web browser.
B Enter “http:// (IP address of this
machine) /” in the [Address] box.
The top page appears on the Web
browser.
47
JupiterC2_GSG_EN_Pre_FM.book Page 48 Tuesday, December 28, 2004 1:39 PM
Document Server
C Click [Document Server].
The Document Server File List appears.
Note
❒ To switch the display format,
click [Details], [Thumbnails] or
[Icons] from the [Display method]
list.
D Click the properties button of the
3
document you want to check.
Information about that document
appears.
E Check the document's content.
Note
❒ To enlarge the document preview, click [Enlarge Image].
Downloading Stored
Documents
Note
❒ File Format Converter is required
when downloading documents
stored in copier or printer mode.
A Start a Web browser.
B Enter “http:// (IP address of this
machine) /” in the [Address] box.
The top page appears on the Web
browser.
C Click [Document Server].
The Document Server File List appears.
Note
❒ To switch the display format,
click [Details], [Thumbnails] or
[Icons] from the [Display method]
list.
48
D Click the properties button of the
document you want to download.
E Select [PDF], [JPEG], or [Multi-page
TIFF] in the [File format] list.
Note
❒ [JPEG] can only be selected for
documents stored in scanner
mode.
❒ [Multi-page TIFF] is available when
file fo rm at converter is installed.
❒ [Multi-page TIFF] cannot be selected for documents stored in
copier or printer mode.
F Click [Download].
G Click [OK].
JupiterC2_GSG_EN_Pre_FM.book Page 49 Tuesday, December 28, 2004 1:39 PM
Settings for the Document Server
Settings for the Document Server
❖ Copier/Document Server Features (See “General Features P.4/5”, Copy Reference.)
Items
General Features
Default
Document Server Storage Key: F1 2 Sided Original Top to Top
Document Server Storage Key: F2 1 Sided→1 Sided Combine
Document Server Storage Key: F3 1 Sided→1 Sided Combine: 4
originals
3
Document Server Storage Key: F4 1 Sided→1 Sided Combine: 8
originals
Document Server Storage Key: F5 Create Margin
❖ System Settings (See p.55 “General Features”, p.58 “Tray Paper Settings”, p.61
“Timer Settings”, and p.63 “Administrator Tools”.)
Items
General Features
Tray Paper Settings
Timer Settings
Administrator Tools
Default
Warm Up Notice
On
Copy Count Display
Up
Output: Document Server
Standard Tray
Paper Tray Priority: Copier
Tray 1
Cover Sheet Tray
Off
Slip Sheet Tray
Off
Copier/Document Server
Auto Reset Timer
60 seconds
Auto Delete File
Yes After 3 day(s)
Delete All Files
--
49
JupiterC2_GSG_EN_Pre_FM.book Page 50 Tuesday, December 28, 2004 1:39 PM
Document Server
3
50
JupiterC2_GSG_EN_Pre_FM.book Page 51 Tuesday, December 28, 2004 1:39 PM
4. User Tools (System Settings)
User Tools Menu (System Settings)
Reference
For details about Interface Settings and File Transfer, see “User Tools Menu
(System Settings)”, Network Guide.
For details about parallel interface, see “System Settings (Parallel Connection)”, Printer Reference.
❖ General Features (See p.55 “General Features”.)
Default
Panel Tone
On
Warm Up Notice
On
Copy Count Display
Up
Function Priority
Copier
Print Priority
Display Mode
Function Reset Timer
3 seconds
Output: Copier
Standard Tray
Output: Document Server
Standard Tray
Output: Facsimile
Standard Tray
Output: Printer
Standard Tray
51
JupiterC2_GSG_EN_Pre_FM.book Page 52 Tuesday, December 28, 2004 1:39 PM
User Tools (System Settings)
❖ Tray Paper Settings (See p.58 “Tray Paper Settings”.)
Default
4
Paper Tray Priority: Copier
Tray 1
Paper Tray Priority: Facsimile
Tray 1
Paper Tray Priority: Printer
Tray 1
Tray Paper Size: Tray 2
Auto Detect
Tray Paper Size: Tray 3
Auto Detect
Tray Paper Size: Tray 4
Auto Detect
Paper Type: Bypass tray
No Display
Paper Type: Tray 1
No Display :2 Sided Copy : Auto Paper Select On
Paper Type: Tray 2
No Display :2 Sided Copy : Auto Paper Select On
Paper Type: Tray 3
No Display :2 Sided Copy : Auto Paper Select On
Paper Type: Tray 4
No Display :2 Sided Copy : Auto Paper Select On
Cover Sheet Tray
Off
Slip Sheet Tray
Off
Printer Bypass Paper Size
81/2”×11”K
❖ Timer Settings (See p.61 “Timer Settings”.)
Default
Auto Off Timer
60 minute(s)
Energy Saver Timer
15 minute(s)
Panel Off Timer
1 minute(s)
System Auto Reset Timer
60 seconds
Copier/Document Server Auto Reset Timer 60 seconds
Facsimile Auto Reset Timer
30 seconds
Printer Auto Reset Timer
60 seconds
Scanner Auto Reset Timer
60 seconds
Set Date
--
Set Time
--
Auto Logout Timer
60 seconds
❖ Interface Settings
• For details about network settings, see “User Tools Menu (System Settings)”, Network Guide.
• For details about parallel interface, see “System Settings (Parallel Connection)”, Printer Reference.
52
JupiterC2_GSG_EN_Pre_FM.book Page 53 Tuesday, December 28, 2004 1:39 PM
User Tools Menu (System Settings)
❖ File Transfer
• For details about network settings, see “User Tools Menu (System Settings)”, Network Guide.
❖ Administrator Tools (See p.63 “Administrator Tools”.)
Default
User Authentication Management
Off
Administrator Authentication Management
Off
Program /Change Administrator
--
Key Counter Management
--
Extended Security
--
Display/Print Counter
--
Display/Clear/Print Counter per User
--
Address Book Management
--
Address Book: Program/Change/Delete Group
--
Address Book: Program/Change/Delete Transfer Request
--
Address Book: Change Order
--
Print Address Book: Destination List
--
Address Book: Edit Title
--
Address Book: Select Title
Title 1
Auto Delete File
Yes After 3 day(s)
Delete All Files
--
Program/Change/Delete LDAP Server
--
Use LDAP Server
Off
AOF (Always ON)
On
Firmware Version
--
Auto Erase Memory Setting
Off
Erase All Memory
--
4
53
JupiterC2_GSG_EN_Pre_FM.book Page 54 Tuesday, December 28, 2004 1:39 PM
User Tools (System Settings)
Accessing User Tools (System Settings)
This section is for administrators in
charge of this machine.
User Tools allow you to change or set
defaults.
Note
❒ Operations for system settings differ from normal operations. Always quit User Tools when you
have finished. See p.54 “Exiting
User Tools”.
4
❒ Any changes you make with User
Tools remain in effect even if the
main power switch or operation
switch is turned off, or the {Energy
Saver}
} or { Clear Modes}
} key is
pressed.
Changing Default Settings
A Press the {User Tools/Counter}} key.
B Press [System Settings].
C Select the menu, and then press
the appropriate key.
Reference
p.51 “User Tools Menu (System
Settings)”
54
D Change settings by following instructions on the display panel,
and then press [OK].
Note
❒ To cancel changes made to settings and return to the initial
display, press the {User
Tools/Counter}
} key.
Exiting User Tools
A Press the {User Tools/Counter}} key.
Note
❒ You can also exit User Tools by
pressing [Exit].
JupiterC2_GSG_EN_Pre_FM.book Page 55 Tuesday, December 28, 2004 1:39 PM
Settings You Can Change with User Tools
Settings You Can Change with User Tools
Reference
To access User Tools, see p.54 “Accessing User Tools (System Settings)”.
General Features
❖ Panel Tone
The beeper (key tone) sounds when a key is pressed.
Note
❒ Default: On
4
❖ Warm Up Notice (Copier/Document Server)
You can set the beeper to sound when the machine becomes ready to copy after switching out of Energy Saver mode, or when the power is turned on.
Note
❒ If the Panel Tone setting is “OFF”, the beeper does not sound, regardless
of the Warm Up Notice setting.
❒ Default: On
❖ Copy Count Display (Copier/Document Server)
The copy counter can be set to show the number of copies made (count up) or
the number of copies yet to be made (count down).
Note
❒ Default: Up (count up)
❖ Function Priority
You can specify the mode to be displayed immediately after the operation
switch is turned on, or when System Reset mode is turned on.
Note
❒ Default: Copier
❖ Print Priority
Print Priority is given to the mode selected.
Reference
p.33 “Multi-Access”
Note
❒ Default: Display Mode
❒ When [Interleave] is selected, the current print job will be interrupted after
a maximum of five sheets.
55
JupiterC2_GSG_EN_Pre_FM.book Page 56 Tuesday, December 28, 2004 1:39 PM
User Tools (System Settings)
❒ When the left tray, 2 tray finisher, or booklet finisher is installed on the machine, you can specify an output tray for each document to be delivered.
For details about how to specify an output tray for each function, see the
following sections:
• p.56 “Output: Copier (copier)”
• p.57 “Output: Document Server (Document Server)”
• p.57 “Output: Facsimile (facsimile)”
• p.57 “Output: Printer (printer)”
❖ Function Reset Timer
You can set the length of time the machine waits before changing modes
when using the multi-access function (see p.33 “Multi-Access”). This is useful
if you are making many copies and have to change settings for each copy. If
you set a longer reset period, you can prevent interruption from other functions.
4
Note
❒ Default: 3 seconds
❒ The Function Reset Timer setting is ignored if [Interleave] is set for Print Priority (see p.55 “Print Priority”).
❒ When you select [Set Time], enter the time (3–30 seconds, in 1 second increments) using the number keys.
❖ Output: Copier (copier)
You can specify a tray to which documents are delivered.
AFZ007S
•
•
•
•
•
•
•
Standard Tray
External Tray
Finisher Shift Tray
Finisher Shift Tray 1
Finisher Shift Tray 2
Left tray 1
Left tray 2
Note
❒ Default: Standard Tray
❒ Paper will be delivered to the standard tray when making a 2 Sided copy,
even if you have specified the external tray.
56
JupiterC2_GSG_EN_Pre_FM.book Page 57 Tuesday, December 28, 2004 1:39 PM
Settings You Can Change with User Tools
❒ Paper will be delivered to the external tray when copying onto OHP transparencies, thick paper, thick paper (back side) or 12" × 18"paper from the
bypass tray, even if you have specified not to use the external tray as the
output tray.
❒ The left tray cannot be used as the output tray for duplex printing.
❖ Output: Document Server (Document Server)
You can specify the tray to which documents are delivered.
Note
❒ Default: Standard Tray
❒ For details about output trays, see p.56 “Output: Copier (copier)”.
❒ The left tray cannot be used as the output tray for duplex printing.
4
❖ Output: Facsimile (facsimile)
You can specify the tray to which documents are delivered.
❒
❒
❒
❒
Note
Default: Standard Tray
For details about output trays, see p.56 “Output: Copier (copier)”.
The left tray cannot be used as the output tray for duplex printing.
If you specify the left tray as the output tray when printing, prints are delivered printed side up.
❖ Output: Printer (printer)
You can specify the tray to which documents are delivered.
Note
❒ Default: Standard Tray
❒ The output trays set on the printer driver have priority over the output tray
specified above.
❒ You cannot use the external tray as the output tray when making a 2 Sided
copy.
❒ For details about output trays, see p.56 “Output: Copier (copier)”.
❒ The left tray cannot be used as the output tray for duplex printing.
Output tray settings
Limitation
❒ You cannot interrupt the current stapling job even if a stapling job is specified
by a different function.
❒ When the 2 tray Finisher or booklet finisher is installed and stapling or shiftsorting is specified for a job, the job will be delivered to the finisher shift tray,
finisher shift tray 1 or finisher shift tray 2 regardless of the output tray specified.
❒ If you use the bypass tray as the input tray, you cannot use the finisher output
tray, left tray 1 or left tray 2 as output trays.
57
JupiterC2_GSG_EN_Pre_FM.book Page 58 Tuesday, December 28, 2004 1:39 PM
User Tools (System Settings)
Tray Paper Settings
❖ Paper Tray Priority: Copier (copier/Document Server)
You can specify the tray to supply paper for output.
Note
❒ Default: Tray 1
❒ When optional paper tray unit is installed, "Tray3" and "Tray4" is displayed.
❒ When optional LCT is installed, "LCT" is displayed.
❖ Paper Tray Priority: Facsimile (facsimile)
You can specify the tray to supply paper for output.
4
Note
❒ Default: Tray 1
❒ When optional paper tray unit is installed, "Tray3" and "Tray4" is displayed.
❒ When optional LCT is installed, "LCT" is displayed.
❖ Paper Tray Priority: Printer (printer)
You can specify the tray to supply paper for output.
Note
❒ Default: Tray 1
❒ When optional paper tray unit is installed, "Tray3" and "Tray4" is displayed.
❒ When optional LCT is installed, "LCT" is displayed.
❖ Tray Paper Size:Tray 2–4
Select the size of the paper loaded in the paper tray.
Note
❒ Tray 1 uses A4Kpaper exclusively. You cannot specify any other paper
size.
❖ The paper sizes you can set for trays are as follows:
• Auto Detect, A3L, B4 JISL, A4K, A4L, A5K
• 11"×17"L, 81/2"×14"L, 81/2"×11"K, 81/2"×11"L, 8"×13"L, 81/2"×13"L,
81/4"×13"L, 71/4"×101/2"L
Important
❒ If the specified paper size differs from the actual size of the paper loaded
in the paper tray, a misfeed might occur because the correct paper size was
not detected.
58
JupiterC2_GSG_EN_Pre_FM.book Page 59 Tuesday, December 28, 2004 1:39 PM
Settings You Can Change with User Tools
Note
❒ The paper guide for the optional LCT is fixed for A4K, 81/2"×11"K size
paper. Contact your service representative if you need to change the paper
size.
❒ Default:
• Tray 2: Auto Detect
• Tray 3: Auto Detect
• Tray 4: Auto Detect
Reference
p.128 “Changing the Paper Size”
❖ Paper Type: Bypass tray
Sets the display so you can see what type of paper is loaded in the bypass tray.
4
❖ The paper types you can set for the bypass tray are as follows:
• No Display, Recycled Paper, Special Paper, Color Paper, Letterhead,
Preprinted Paper, Thick Paper, OHP, Plain: Dup.Back, Thick: Dup.Back
Note
❒ Default: No Display
❖ Paper Type: Tray 1–4
Sets the display so you can see what type of paper is loaded in each paper
tray. The print function uses this information to automatically select the paper tray.
❖ The paper types you can set for trays are as follows:
• No Display, Recycled Paper, Special Paper, Color Paper, Letterhead,
Preprinted Paper
Note
❒ Default:
• Paper Type: No Display
• Copying Method in Duplex: 2 Sided Copy
• Apply Auto Paper Select: Yes
❒ When paper of the same type and size is loaded in two different paper
trays and you want to specify tray for 2 Sided Copy and tray for 1 Sided
Copy, specify the upper tray for 2 Sided Copy. If one of the trays is specified as the default in Paper Tray Priority, assign 2 Sided Copy to that tray.
❒ A mark appears next to the paper tray if [No] is selected in Auto Paper
Select.
Limitation
❒ [Auto Paper Select] can only be selected for the copier function if [No Display]
and [Recycled Paper] are selected. If [No] is selected, Auto Paper Select is not
valid for the tray.
59
JupiterC2_GSG_EN_Pre_FM.book Page 60 Tuesday, December 28, 2004 1:39 PM
User Tools (System Settings)
❖ Cover Sheet Tray
Allows you to specify and display the paper tray that is setting cover sheets.
After selecting the paper tray, you can also specify the display timing and
copy method for two-sided copying.
Note
❒ Default:
• Tray to Program: Off
❒ Functions using the cover sheet tray setting are the front cover function
and front/back cover function.
❒ When [At Mode Selected] is selected, cover sheet tray settings only appear
when the cover function or slip sheet function is selected.
❒ When [Full Time] is selected, the cover sheet tray is always displayed.
❒ You can set Copying Method in Duplex only when [At Mode Selected] is selected.
4
Reference
“Covers”, Copy Reference
❖ Slip Sheet Tray
Allows you to specify and display the paper tray that will be inserting slip
sheets. After selecting the paper tray, you can also specify the display timing
and copy method.
Note
❒ Default:
• Tray to Program: Off
❒ When [At Mode Selected] is selected, slip sheet tray settings only appear
when the cover function or slip sheet function is selected.
Reference
“Slip Sheets”, Copy Reference
❖ Printer Bypass Paper Size
You can specify the size of the paper in the bypass tray when printing data
from the computer.
• The paper types you can set for trays are as follows:
A3L, A4K, A4L, A5K, A5L, A6L, B4 JISL, B5 JISK, B5 JISL, B6
JISL, C5 EnvK, C6 EnvK, DL EnvK, 12 × 18L, 11 × 17L, 81/2 × 14L,
81/2 × 13L, 81/2 × 11K, 81/2 × 11L, 81/4 × 13L, 8 × 13L, 71/4 × 101/2K,
71/4 × 101/2L, 51/2 × 81/2L, 41/8 × 91/2K, 37/8 × 71/2K, 8KL, 16KK,
16KL
Note
❒ Default:81/2”×11”K
❒ You can specify a custom size of between 100.0 and 139.7 mm (4.0"-5.5")
vertically, and between 457.2 and 600.0 mm (18.0"-23.7) horizontally.
60
JupiterC2_GSG_EN_Pre_FM.book Page 61 Tuesday, December 28, 2004 1:39 PM
Settings You Can Change with User Tools
Timer Settings
❖ Auto Off Timer
After a specified time has elapsed following job completion, the machine automatically turns off in order to conserve energy. This function is called “Auto Off”.
The machine status after the Auto Off operation is referred to as “Sleep
mode”. For the Auto Off Timer, specify the time to elapse before Auto Off.
Note
❒ Default: 60 minute(s)
❒ Enter a time interval between 10 seconds and 240 minutes, using the number keys.
❒ From “Sleep mode”, the machine is ready to use within 101 seconds.
❒ Auto Off may not work when error messages appear.
4
❖ Energy Saver Timer
Set the amount of time the machine waits before switching to lower-power
mode after copying has finished or the last operation is performed.
The time can be set from 1 minute to 240 minutes using the number keys.
Note
❒ Default: 15 minute(s)
❖ Panel Off Timer
Set the amount of time the machine waits before switching the panel off after
copying has finished or the last operation is performed.
Note
❒ The warm up time for making a copy from standby mode is 3 seconds for
Panel off Level 1 and 15 seconds for Panel off Level 2.
❒ Default: 1 minute(s)
❒ Enter a time interval between 10 seconds and 240 minutes, using the number keys.
❖ System Auto Reset Timer
The System Reset setting automatically switches the screen to that of the function set in Function Priority, when no operations are in progress, or when an
interrupted job is cleared. This setting determines the system reset interval.
See p.55 “Function Priority”.
Note
❒ Default: On, 60 seconds
❒ The time can be set from 10 to 999 seconds, using the number keys.
61
JupiterC2_GSG_EN_Pre_FM.book Page 62 Tuesday, December 28, 2004 1:39 PM
User Tools (System Settings)
❖ Copier/Document Server Auto Reset Timer (copier/Document Server)
Specifies the time to elapse before copier and Document Server modes reset.
Note
❒ If [Off] is selected, the machine does not automatically switch to the user
code entry screen.
❒ Default: On, 60 Seconds
❒ The time can be set from 10 to 999 seconds, using the number keys.
❖ Facsimile Auto Reset Timer (facsimile)
Specifies the time to elapse before the facsimile mode resets.
Note
❒ Default: On, 30 seconds
❒ The time can be set from 30 to 999 seconds, using the number keys.
4
❖ Printer Auto Reset Timer (printer)
Specifies the time to elapse before the printer function resets.
Note
❒ Default: On, 60 seconds
❒ If [Off] is selected, the machine does not automatically switch to the user
code entry screen.
❒ The time can be set from 10 to 999 seconds, using the number keys.
❖ Scanner Auto Reset Timer (scanner)
Specifies the time to elapse before the scanner function resets.
Note
❒ If [Off] is selected, the machine does not automatically switch to the user
code entry screen.
❒ Default: On, 60 seconds
❒ The time can be set from 10 to 999 seconds, using the number keys.
❖ Set Date
Set the date for the copier's internal clock using the number keys.
Note
❒ To change between year, month, and day, press [←
←] and [→
→].
❖ Set Time
Set the time for the copier's internal clock using the number keys.
Note
❒ To change between hours, minutes and seconds, press [←
←] and [→
→].
❒ Enter the time using the 24–hour format (in 1 second increments).
62
JupiterC2_GSG_EN_Pre_FM.book Page 63 Tuesday, December 28, 2004 1:39 PM
Settings You Can Change with User Tools
❖ Auto Logout Timer
You can specify whether or not to automatically log out a user when the user
does not operate the machine for a specified period of time after logging in.
Note
❒ Default: On, 60 seconds
❒ When [On] is selected, the time can be set from 10 to 999 seconds, in one second increments, using the number keys.
Administrator Tools
Administrator Tools are used by the administrator. To change these settings,
contact the administrator.
We recommend specifying Administrator Authentication before making Administrator Tools settings.
See Security Reference.
4
❖ User Authentication Management
• User Code Authentication
Allows you to control who uses the machine by setting codes for users.
User codes must be registered for User Code Authentication.
Note
❒ If User Code Authentication has been specified, Auto Color Selection
cannot be used.
❒ By using "PC Control" for the printer, you can keep a print log for each
user code entered from the driver.
Reference
For details about Basic Authentication, Windows Authentication, and
LDAP Authentication, see Security Reference.
❖ Administrator Authentication Management
See Security Reference.
❖ Program/ Change Administrator
See Security Reference.
❖ Key Counter Management
You can specify that functions that you want to manage with the key counter.
❖ Extended Security
You can specify whether or not to use the extended security functions. For details about the extended security functions, see Security Reference.
63
JupiterC2_GSG_EN_Pre_FM.book Page 64 Tuesday, December 28, 2004 1:39 PM
User Tools (System Settings)
❖ Display/Print Counter
Allows you to view and print the various counters.
• Display/Print Counter
Displays counters for each functions (Total, Copier, Facsimile, Printer,
A3/DLT, Duplex, Staple).
• Print Counter List
Prints out a list of counters for each functions.
• To print the counter list
A Press the {User Tools/Counter}
} key.
B Press [System Settings].
C Press [Administrator Tools].
D Press [Display / Print Counter].
E Press [Print Counter List].
4
F
G
Press the {Start}
} key.
Press [Exit].
❖ Display/Clear/Print Counter per User
Allows you to view and print the various counters accessed with users and to
set the values to 0.
Note
❒ Press [U
UPrev.] and [T
TNext] to show all counters.
• Print Counter for All Users
Prints the counter values for all the users.
• Clear Counter for All Users
Sets the counter value for all the users.
• Print Counter per User
Prints the counter values for each user.
• Clear Counter per User
Sets the counter value for each user.
Note
❒ To print a list for each user, see p.77 “Printing the Counter for Each User
Code”.
64
JupiterC2_GSG_EN_Pre_FM.book Page 65 Tuesday, December 28, 2004 1:39 PM
Settings You Can Change with User Tools
❖ Address Book Management
You can add, change or delete information registered in the Address Book.
For details, see p.70 “Address Book”.
• [Program / Change]
You can register and change names as well as user codes.
• Names
You can register a name, key display, registration number, and title selection.
• Auth. Info
You can register a user code, and specify the functions available to each
user code. You can also register user names and passwords to be used
when sending e-mail, sending files to folders, or accessing an LDAP server.
• Protection
You can register a protection code.
• Fax Dest.
You can register a fax number, international TX mode, fax header, label insertion, IP-Fax destination, and protocol.
• E-mail
You can register an e-mail address.
• Folder
You can register the protocol, path, user name, password, port number,
and server name.
• Add to Group
You can put names registered in the Address Book into a group.
• [Delete]
You can delete a name from the Address Book.
4
Note
❒ You can register up to 2,000 names.
❒ You can register up to 500 user codes.
❒ You can also register user codes from SmartDeviceMonitor for Admin.
❖ Address Book: Program/Change/Delete Group
Names registered in the Address Book can be added into a group.
You can then easily manage the names registered in each group. For details,
see p.96 “Registering Names to a Group”.
• [Program / Change]
You can register new groups, or changes a group name, key display, title
selection or registration number.
• [Delete]
You can delete a group.
Note
❒ You can register up to 100 groups.
❒ You can also group users using a Web browser. For more information, see
the Web Browser help.
65
JupiterC2_GSG_EN_Pre_FM.book Page 66 Tuesday, December 28, 2004 1:39 PM
User Tools (System Settings)
❖ Address Book: Program / Change / Delete Transfer Request
You can register fax destinations for the Transfer Request function in facsimile mode.
For details about operations, see p.103 “Registering the Transfer Request”.
• [Program / Change]
This registers new transfer requests and receiving stations, or changes the
transfer request name, key name, title selection, registration number, fax
destination, IP-Fax destination, or e-mail address.
• [Delete]
Deletes a transfer request.
Note
❒ You can register up to 10 transfer requests.
4
❖ Address Book: Change Order
You can change the order of the names in the Address Book.
Note
❒ You can rearrange the order of items that are on the same page, but you
cannot move the items to another page. For example, you cannot move an
item from “PLANNING” ([OPQ]) to “DAILY” ([CD]).
A Press the {User Tools/Counter}
} key.
B Press [System Settings].
C Press [Administrator Tools], and then press [T
TNext].
D Press [Address Book: Change Order].
E Press the name key to be moved.
F
66
Note
❒ You can also select a name using the number keys.
Press the name key in the place that you want to move to.
JupiterC2_GSG_EN_Pre_FM.book Page 67 Tuesday, December 28, 2004 1:39 PM
Settings You Can Change with User Tools
The name selected in step E moves to the place selected in step F, and the
keys for other names will be shifted accordingly.
Note
❒ You can also select a name using the number keys.
❖ Print Address Book: Destination List
You can print the list of names registered in the Address Book.
• Print in Title 1 Order
Prints a list of the names according to the order in Title 1.
• Print in Title 2 Order
Prints a list of the names according to the order in Title 2.
• Print in Title 3 Order
Prints a list of the names according to the order in Title 3.
• Print Group Dial List
Prints a list of the groups registered.
A Select the print format.
B To print on two-sided pages, select [Print on 2 Sides].
C Press the {Start}
} key.
The list is printed.
4
❖ Address Book: Edit Title
You can edit the title to locate the desired user easily.
A Press the {User Tools/Counter}
} key.
B Press [System Settings].
C Press [Administrator Tools], and then press [T
TNext].
D Press [Address Book: Edit Title].
E Press the title key to be changed.
F
G
Enter the new name, and then press [OK].
Press [OK].
67
JupiterC2_GSG_EN_Pre_FM.book Page 68 Tuesday, December 28, 2004 1:39 PM
User Tools (System Settings)
❖ Address Book: Select Title
You can specify the title to select a name.
Note
❒ Default: Title 1
❖ Auto Delete File
You can specify whether documents stored in the Document Server will or
will not be deleted after a specified period of time.
❒
❒
❒
❒
❒
4
Note
Default: Yes After 3 day(s)
If you select [Yes], documents stored subsequently will be deleted.
If you select [No], documents will not be deleted automatically.
If you select [Yes], enter a number of days in the range of 1 - 180.
The default setting is three days, which means documents will be deleted
three days (72 hours) after they have been stored.
❖ Delete All Files
All documents stored in Document Server will be deleted.
Note
❒ Even if a password has been set, all documents will be deleted.
❒ A confirmation dialog box will appear. To delete all documents, select [Yes].
❖ Program/Change/Delete LDAP Server
See “Program/Change/Delete LDAP Server”, Network Guide.
❖ Use LDAP Server
You can specify whether or not to use the LDAP server.
Note
❒ Default: Off
❒ When Use LDAP Server is set to Off, [Search LDAP] will not appear on the
searching display.
❖ AOF (Always On)
Specify whether or not to use Auto Off function.
Note
❒ Default: On
❒ For details about this function, contact your service representative.
❖ Firmware Version
You can check the version of the softwares installed in this machine.
68
JupiterC2_GSG_EN_Pre_FM.book Page 69 Tuesday, December 28, 2004 1:39 PM
Settings You Can Change with User Tools
❖ Auto Erase Memory Setting
When the optional DataOverwriteSecurity Unit is installed, you can specify if
data is to be automatically deleted after a job is completed.
Note
❒ Default: Off
❒ You can also specify the method of overwriting.
Reference
See the manual for DataOverwriteSecurity Unit.
❖ Erase All Memory
When the optional DataOverwriteSecurity Unit is installed, you can erase all
the data stored in the hard disk drive of the machine.
4
Reference
See the manual for DataOverwriteSecurity Unit.
69
JupiterC2_GSG_EN_Pre_FM.book Page 70 Tuesday, December 28, 2004 1:39 PM
User Tools (System Settings)
Address Book
Registering information such as the
names of users and their e-mail addresses in the Address Book allows
you to manage them easily.
Important
❒ Address Book data is stored on the
hard disk. It can be lost if there is
some kind of hard disk failure. The
manufacturer shall not be responsible for any damages resulting
data loss.
4
Note
❒ You can also use a Web browser to
register names in the Address
Book. With SmartDeviceMonitor
for Admin, you can register multiple names at the same time.
❒ Using [Address Management Tool] in
SmartDeviceMonitor for Admin,
you can backup Address Book data. We recommend backing up Address Book data.
You can register and manage the following items in the Address Book:
❖ Name
You can register the name of the
user and the key display. This is
the basic information required for
managing users of the machine.
❖ Authentication Information
You can register user codes in order to restrict particular functions
to certain users, and to check their
use of each function. You can also
register login user names and login
passwords to be used when sending e-mail, sending to folders, or
accessing an LDAP server.
Reference
For details about using a Web
browser, see the Web browser
Help.
For details about SmartDeviceMonitor for Admin and how to install it, see Printer Reference.
For operating instructions, see
SmartDeviceMonitor for Admin
Help.
70
❖ Fax Dest.
You can register fax numbers, line,
fax header and select label insertion.
When using IP-Fax, you can register the IP-Fax destination and select the protocol.
• Fax Destination
JupiterC2_GSG_EN_Pre_FM.book Page 71 Tuesday, December 28, 2004 1:39 PM
Address Book
• IP-Fax Destination
❖ Add to Group
You can put registered e-mail and
folder destinations into a group for
easier management.
❖ E-mail
You can register e-mail destinations in the Address Book.
Managing names in the Address Book
❖ Folder
You can register the protocol, path
name and server name.
• SMB
• FTP
❖ Protection
You can set protection codes to
stop sender's name from being
used or folders from being accessed without authorization.
By registering a name and key display beforehand, you can specify email and folder destinations simply
by selecting the name key.
See p.73 “Registering Names”.
4
Sending fax by Quick Dial
Register a fax number in the Address
Book so you can specify it simply by
selecting the fax destination, shown
on the fax initial display when sending a fax. When label insertion is set to
“ON”, the receiver's name and standard messages are printed on the fax
message when it is received at the
other end.
By registering IP-Fax destinations in
the Address Book, you can specify a
destination simply by selecting it
from the destinations that appear in
the initial fax display.
See p.79 “Fax Destination”.
71
JupiterC2_GSG_EN_Pre_FM.book Page 72 Tuesday, December 28, 2004 1:39 PM
User Tools (System Settings)
4
Sending e-mail by Quick Dial
Managing users and machine usage
By registering e-mail addresses in the
Address Book, you can specify e-mail
destinations simply by selecting them
from the fax initial display when
sending a document by internet fax.
You can also specify an e-mail address by selecting the destination
shown on the initial scanner display
when sending a document using the
scanner function.
A registered e-mail address can be
used as the sender's address, and the
sender's address are automatically
entered in the “From” field of an email header.
See p.86 “E-mail Destination”.
Register user codes to limit users to
the following functions and check
their use of each function:
• Copier
• Document Server
• Facsimile
• Scanner
• Printer
See p.75 “Authentication Information”.
Sending scanned files to a shared folder
directly
After registering the path name, user
name and password, you can connect
to a shared folder simply by selecting
the destination shown on the initial
scanner display whenever sending
files using the scanner function to a
shared folder.
To share the folder using Windows,
select the SMB protocol.
To register the folder to the FTP server, select the FTP protocol.
See p.89 “Registering Folders”.
Preventing unauthorized user access to
shared folders from the machine
After registering a protection code,
you can specify the object of protection to prevent an e-mail destination
from being used without permission.
You can prevent unauthorized access
to registered folders. See p.101 “Registering a Protection Code”.
72
JupiterC2_GSG_EN_Pre_FM.book Page 73 Tuesday, December 28, 2004 1:39 PM
Registering Names
Registering Names
The user name is useful for selecting a
destination when sending faxes or email. You can also use it as a folder
destination.
H Press the key for the classification
you want to use under Select Title.
Registering a Name
A Press the {User Tools/Counter}} key.
B Press [System Settings].
C Press [Administrator Tools], and then
press [T
TNext].
D Press [Address Book Management].
E Press [New Program].
F Press [Change] on the right of the
Name.
The name entry display appears.
G Enter
the name, and then press
[OK].
Note
❒ The name can be used for documents in the Document Server.
For details about the Document
Server, see p.39 “Using the Document Server”.
Reference
p.159 “Entering Text”
Note
❒ The keys you can select are as
follows:
• [Freq.]… Added to the page
that is displayed first.
• [AB], [CD], [EF], [GH], [IJK],
[LMN], [OPQ], [RST], [UVW],
[XYZ], [1] to [10]… Added to
the list of items in the selected title.
❒ You can select [Freq.] and one
more page for each title.
4
I To continue registering the name,
press [Continue to Program], and
then repeat the procedure from
step F.
J Press [OK].
K Press [Exit].
L Press the {User Tools/Counter}} key.
Changing a Registered Name
A Press the {User Tools/Counter}} key.
B Press [System Settings].
C Press [Administrator Tools], and then
press [T
TNext].
D Press [Address Book Management].
73
JupiterC2_GSG_EN_Pre_FM.book Page 74 Tuesday, December 28, 2004 1:39 PM
User Tools (System Settings)
E Select
the registered name you
want to change.
Press the name key, or enter the
registered number using the number keys
Note
❒ If you press , you can search
by the registered name, user
code, fax number, folder name
e-mail address, or IP-Fax destination.
To change the name or key
display
4
A Press [Change] on the right of
the name or key display.
B Enter the name or key display,
and then press [OK].
Reference
p.159 “Entering Text”
To change the title
A Press the key for the classification you want to use from Select Title.
F Press [OK].
G Press [Exit].
H Press the {User Tools/Counter}} key.
74
Deleting a Registered Name
If you delete a name, data associated
with that name, such as e-mail addresses, fax number, and folder
name, is also deleted.
A Press the {User Tools/Counter}} key.
B Press [System Settings].
C Press [Administrator Tools], and then
press [T
TNext].
D Press [Address Book Management].
E Press [Delete].
F Select the name you want to de-
lete.
Press the key, or enter the registered number using the number
keys
G Press [Yes].
H Press [Exit].
I Press the {User Tools/Counter}} key.
JupiterC2_GSG_EN_Pre_FM.book Page 75 Tuesday, December 28, 2004 1:39 PM
Authentication Information
Authentication Information
Register user codes to limit users to
the following functions and check
their use of each function:
• Copier
• Document Server
• Facsimile
• Scanner
• Printer
Note
❒ The number of copies made of documents stored in the Document
Server using the facsimile function
is counted for each user code. This
allows you to check each user's usage.
❒ The number of copies scanned using the scanner function is counted
for each user code. This allows you
to check each user's usage.
❒ To automatically register the printer driver user code, select [PC Control] for the printer in User Code
Authentication. To use the user
code set in User Tools, select [Black
& White] or [Color]. Set the user
codes registered in User Tools for
the printer driver. See p.63 “User
Authentication Management”.
Reference
For details about setting user codes
for the printer driver, see Printer
Reference or the printer driver
Help.
Important
❒ The functions associated with each
user code are the same. If you
change or delete user codes, management data and limits associated
with that code become invalid.
Registering a New User Code
A Press the {User Tools/Counter}} key.
B Press [System Settings].
4
C Press [Administrator Tools], and then
press [T
TNext].
D Press [Address Book Management].
E Press the name whose code is to
be registered, or enter the registered number using the number
key.
Note
❒ To register the name, see p.73
“Registering a Name”.
F Press [Auth. Info].
G Enter the user
code using the
number keys, and then press [#].
Note
❒ If you make a mistake, press
[Clear] or the {Clear/Stop}
} key,
and then enter the code again.
75
JupiterC2_GSG_EN_Pre_FM.book Page 76 Tuesday, December 28, 2004 1:39 PM
User Tools (System Settings)
H Press [TTNext] twice.
I Select the functions
to be used
with the user code from Available
Functions.
❒ To change the name, key display and title, see p.73 “Changing a Registered Name”.
F Press [Auth. Info].
G Press [Change], and then enter the
new user code using the number
keys
J Press [OK].
Note
❒ To continue registering user
codes, repeat the procedure
from step E.
4
K Press [Exit].
L Press the {User Tools/Counter}} key.
Changing a User Code
To change the available functions
A Press [T
TNext] twice.
B Press the key to select the functions to enable them.
Note
❒ Even if you change a user code, the
counter value will not be cleared.
Note
❒ Press the key to highlight it,
and then the function is enabled. To cancel a selection,
press the highlighted key.
A Press the {User Tools/Counter}} key.
B Press [System Settings].
C Press [Administrator Tools], and then
I Press [OK].
J Press [Exit].
K Press the {User Tools/Counter}} key.
D Press [Address Book Management].
E Select the user whose user code
Deleting a User Code
press [T
TNext].
you want to change.
Press the name key, or enter the
registered number using the number keys.
76
H Press [#].
Note
❒ If you press , you can search
for a user by name/index, user
code, fax number, folder name
e-mail address, or IP-Fax destination.
Note
❒ After clearing the user code, the
counter is automatically cleared.
❒ To delete a name from the Address
Book entirely, see p.74 “Deleting a
Registered Name”.
A Press the {User Tools/Counter}} key.
B Press [System Settings].
JupiterC2_GSG_EN_Pre_FM.book Page 77 Tuesday, December 28, 2004 1:39 PM
Authentication Information
C Press [Administrator Tools], and then
press [T
TNext].
D Press [Address Book Management].
E Select the name whose code is to
be deleted.
Press the name key, or enter the
registered number using the number keys.
F Press [Auth. Info].
G Press [Change] to delete the user
code, and then press [#].
H Press [OK].
I Press [Exit].
J Press the {User Tools/Counter}} key.
Printing the Counter for Each
User Code
A Press the {User Tools/Counter}} key.
B Press [System Settings].
C Press [Administrator Tools].
D Press [Display / Clear / Print Counter
per User].
E Select
a user code from the left
side of the display.
4
Note
❒ Press [Select All on the Page] to select all user codes on the page.
F Press [Print Counter List] under Per
User.
Displaying the Counter for
Each User Code
A Press the {User Tools/Counter}} key.
B Press [System Settings].
C Press [Administrator Tools].
D Press [Display / Clear / Print Counter
per User].
E Select [Copy Counter], [Print Counter],
[Transmission Counter] or [Scanner
Counter].
Counters for individual function
usage under each user code appear.
Note
❒ Enter the user code, and then
press [#] if the user code is registered.
G Select
the function usage you
want to print from [Copy Counter],
[Print Counter], [Transm ission
Counter], and [Scanner Counter].
H Press [Print].
77
JupiterC2_GSG_EN_Pre_FM.book Page 78 Tuesday, December 28, 2004 1:39 PM
User Tools (System Settings)
To print the number of prints for all
user codes
A Press the {User Tools/Counter}} key.
B Press [System Settings].
C Press [Administrator Tools].
D Press [Display / Clear / Print Counter
per User].
E Press [Print Counter List] under All
Users.
4
Note
❒ Enter the user code, and then
press [#] if the user code is registered.
F Select
the function usage you
want to print from [Copy Counter],
[Print Counter], [Transmission
Counter], and [Scanner Counter].
E Select the user code to clear.
To clear the number of prints
made under a user code
A Select the user code from the
left side of the display.
Note
❒ Press [Select All on the Page] to
select all user codes on the
page.
B Press [Clear] under Per User.
C Select the function usage you
want to clear from [Copy
Counter], [Print Counter], [Transmission Counter], and [Scanner
Counter].
D Press [OK].
To clear the number of prints for
all user codes
A Press [Clear] under All Users.
G Press [Print].
Clearing the Number of Prints
A Press the {User Tools/Counter}} key.
B Press [System Settings].
C Press [Administrator Tools].
D Press [Display / Clear / Print Counter
per User].
78
B Select the function usage you
want to clear from [Copy
Counter], [Print Counter], [Transmission Counter], and [Scanner
Counter].
C Press [OK].
F Press [Exit].
G Press the {User Tools/Counter}} key.
JupiterC2_GSG_EN_Pre_FM.book Page 79 Tuesday, December 28, 2004 1:39 PM
Fax Destination
Fax Destination
Register a fax destination so you do
not need to enter fax numbers each
time, and can send documents that
have been scanned in using the facsimile function.
• It is easy to select the fax destination if you register a “User (Destination) Name” and “Key Display”
for the fax destination.
• You can register the fax destinations by selecting them from redial
function.
• You can register fax destinations as
a group.
There are two types of fax destination, as shown below:
• Fax Destination
Select this to send the fax over the
telephone network.
• IP-Fax
Select this to send the fax to a machine on a TCP/IP network.
Limitation
❒ You cannot send the fax to a machine on another network if that
network is behind a firewall.
❖ Fax Destination
You can program the following
items in a fax destination:
• Fax number
Registers the destination's fax
number. You can enter a fax
number using up to 128 digits.
You must include every digit in
the number.
• SUB Code
Registering a SUB Code allows
you to use Confidential Transmission to send messages to the
other fax machines that support
a similar function called “SUB
Code”. See “SUB Code”, Facsimile Reference <Advanced Features>.
• SEP Code
Registering a SEP Code allows
you to use Polling Reception to
receive faxes from the other fax
machines that support Polling
Reception. See “SEP Code”, Facsimile Reference <Advanced Features>.
• Line
If the optional extra G3 interface
unit is installed, you can select
the line type for each destination.
• Fax header
You can select to print a fax
header on fax messages the other party receives. The default is
“1st Name”. See Facsimile Reference <Advanced Features>.
• Label insertion
With this function you can have
the receiver's name printed on
the message when it is received
at the other end. The name is
printed at the top of the page
and will be preceded by “To”.
You can also have a standard
message stamped on the second
and third lines after that.
4
Note
❒ Fax header and label insertion are also printed when
sending by e-mail using the
fax function.
79
JupiterC2_GSG_EN_Pre_FM.book Page 80 Tuesday, December 28, 2004 1:39 PM
User Tools (System Settings)
❒ You can program a standard
message other than those
registered in the machine.
See “Programming, Changing, and Deleting Standard
Messages”, Facsimile Reference <Advanced Features>.
• International TX mode
When setting the International
TX mode to [On], the machine
transmits more carefully by
lowering transmission speed.
However, it may take a longer
time to send a fax.
4
❖ IP-Fax Destination
You can program the following
items in an IP-Fax Destination:
Note
❒ This setting only works if the IP
fax function has been selected.
80
• IP-Fax
Register the IP-Fax destination.
You can register the destination
using up to 128 characters. You
must make this setting when using IP-Fax.
• SUB Code
Registering a SUB Code allows
you to use Confidential Transmission to send messages to the
other fax machines that support
a similar function called “SUB
Code”. See “SUB Code”, Facsimile Reference <Advanced Features>.
• SEP Code
Registering a SEP Code allows
you to use Polling Reception to
receive faxes from the other fax
machines that support Polling
Reception. See “SEP Code”, Facsimile Reference <Advanced Features>.
• Select Protocol
Select the protocol for the IPFax transmission.
Registering a Fax Destination
A Press the {User Tools/Counter}} key.
B Press [System Settings].
C Press [Administrator Tools], and then
press [T
TNext].
D Press [Address Book Management].
E Select the name whose fax destination you want to register.
Press the name key, or enter the
registered number using the number keys.
Note
❒ If you press , you can search
by the registered name, user
code, fax number, folder name
e-mail address, or IP-Fax destination.
❒ To register the name, key display, and title, see p.73 “Registering a Name”.
F Press [Fax Dest.].
G Enter the fax number
using the
number keys, and then press [OK].
JupiterC2_GSG_EN_Pre_FM.book Page 81 Tuesday, December 28, 2004 1:39 PM
Fax Destination
To select the line
To set the International TX Mode
A Press [Select Line].
A Press [Change] under International TX Mode.
B Select [Off] or [On], and then
press [OK].
To select the fax header
B Select the line, and then press
[OK].
To program the SUB Code
A Press [Adv. Features], and then
select [SUB Code].
B Press [Change] under TX SUB
Code.
C Enter a SUB Code using the
number keys, and then press
[OK].
D To enter a password, press
[Cha ng e] u n de r Pa ss w o rd
(SID).
E Enter a password using the
number keys, and then press
[OK].
F Press [OK].
To program the SEP Code
A Press [Adv. Features], and then
select [SEP Code].
B Press [Change] under RX SEP
Code.
C Enter a SEP Code using the
number keys, and then press
[OK].
D To enter a password, press
[Cha ng e] u n de r Pa ss w o rd
(PWD).
E Enter a password using the
number keys, and then press
[OK].
F Press [OK].
Note
❒ You can register the fax header
name in Program Fax Information in the system settings for
Facsimile Features. See “Programming”, Facsimile Reference
<Basic Features>.
A Press [Change] under Fax Header.
B Select [1st Name] or [2nd Name],
and then press [OK].
4
To set label insertion
When Label Insertion is set to ON,
the receiver's name and standard
messages are printed on the fax
message when it is received at the
other end.
A Press [Change] under Label Insertion.
B Select [On].
C Press [Change] under Line 2.
D Select a standard message to
print on the second line. To
stamp a customized message,
press [Custom Message].
E Enter a message, and then press
[OK].
81
JupiterC2_GSG_EN_Pre_FM.book Page 82 Tuesday, December 28, 2004 1:39 PM
User Tools (System Settings)
Reference
p.159 “Entering Text”
F Press [OK].
G Press [Change] under Line 3.
H Select a standard message, and
then press [OK].
I Press [OK].
F Press [Fax Dest.].
G Change the settings.
To change the fax number
A Press [Change] under Facsimile
No..
H Press [OK].
Note
❒ When a group is registered, you
can also set label insertion to the
group. See p.96 “Registering
Names to a Group”.
4
I Press [Exit].
J Press the {User Tools/Counter}} key.
Changing a Registered Fax
Destination
A Press the {User Tools/Counter}} key.
B Press [System Settings].
C Press [Administrator Tools], and then
press [T
TNext].
D Press [Address Book Management].
E Select the name whose fax desti-
nation you want to change.
Press the name key, or enter the
registered number using the number keys.
Note
❒ If you press , you can search
by the registered name, user
code, fax number, folder name
e-mail address, or IP-Fax destination.
❒ To change the name, key display and title, see p.73 “Changing a Registered Name”.
82
B Enter the new fax number using the number keys, and then
press [OK].
To change the line
A Press [Select Line].
B Select the line.
C Press [OK].
To change the SUB Code
A Press [Adv. Features].
B Press [SUB Code].
C Press [Change] under TX SUB
Code.
D Enter the new SUB Code, and
then press [OK].
E To change the password, press
[Ch an ge] u n d er P ass w o rd
(SID).
F Enter the new password, and
then press [OK].
G Press [OK].
JupiterC2_GSG_EN_Pre_FM.book Page 83 Tuesday, December 28, 2004 1:39 PM
Fax Destination
To change the SEP Code
A Press [Adv. Features].
B Press [SEP Code].
C Press [Change] under RX SEP
Code.
D Enter the new SEP Code, and
then press [OK].
E To change the password, press
[Cha ng e] u n de r Pa ss w o rd
(PWD).
F Enter the new password, and
then press [OK].
G Press [OK].
To change the fax header
A Press [Change] under Fax Header.
B Select the new fax header, and
then press [OK].
To change the label insertion
A Press [Change] under Label Insertion.
B Press [Change] under Line 2.
C Select the new standard message or press [Custom Message]
to enter the new message.
D Press [OK].
E Press [Change] under Line 3.
F Select the new standard message, and then press [OK].
G Press [OK].
H Press [OK].
Note
❒ To change the name, key display and title, see p.73 “Changing a Registered Name”.
I Press [Exit].
J Press the {User Tools/Counter}} key.
Deleting a Registered Fax
Destination
Note
❒ If you delete a destination that is a
specified delivery destination,
messages to its registered Personal
Box, for example, cannot be delivered. Be sure to check the settings
in the fax function before deleting
any destinations.
❒ To delete a name entirely, see p.74
“Deleting a Registered Name”.
4
A Press the {User Tools/Counter}} key.
B Press [System Settings].
C Press [Administrator Tools], and then
press [T
TNext].
D Press [Address Book Management].
E Select the name whose fax destination you want to delete.
Press the name key, or enter the
registered number using the number keys.
Note
❒ If you press , you can search
by the registered name, user
code, fax number, folder name
e-mail address, or IP-Fax destination.
❒ To delete the name, key display,
and title, see p.74 “Deleting a
Registered Name”.
F Press [Fax Dest.].
G Press [Change] under
Facsimile
No..
83
JupiterC2_GSG_EN_Pre_FM.book Page 84 Tuesday, December 28, 2004 1:39 PM
User Tools (System Settings)
H Press
[Delete All], and then press
[OK].
I Press [OK].
J Press [Exit].
K Press the {User Tools/Counter}} key.
4
Note
❒ If you press , you can search
by the registered name, user
code, fax number, folder name
e-mail address, or IP-Fax destination.
❒ To register the name, key display, and title, see p.73 “Registering a Name”.
F Press [Fax Dest.]
G Press [IP-Fax].
Registering an IP-Fax
Destination
Reference
For details about sending an IPFax, see Facsimile Reference <Basic
Features>.
A Press the {User Tools / Counter}} key.
H Press
[Change]. Enter the IP-Fax
destination and then press [OK].
To program the SUB Code
A Press [Adv. Features], and then select [SUB Code].
B Press [System Settings].
C Press [Administrator Tools], and then
press [T
TNext].
D Press [Address Book Management].
E Select the name whose IP-Fax
destination you want to register.
Press the name key, or enter the
registered number using the number keys.
B Press
[Change] under TX SUB
Code.
C Enter a SUB Code using the number keys, and then press [OK].
D To enter a password, press [Change]
under Password (SID).
E Enter a password using the number keys, and then press [OK].
F Press [OK].
To program the SEP Code
A Press [Adv. Features], and then select [SEP Code].
B Press [Change] under RX SEP Code.
84
JupiterC2_GSG_EN_Pre_FM.book Page 85 Tuesday, December 28, 2004 1:39 PM
Fax Destination
C Enter a SEP Code using the number keys, and then press [OK].
D To enter a password, press [Change]
under Password (PWD).
E Enter a password using the number keys, and then press [OK].
F Press [OK].
To change the SUB Code
A Press [Adv. Features].
B Press [SUB Code].
C Press [Change] under TX SUB Code.
D Enter the new SUB Code, and
then press [OK].
To select the protocol
E To
A Select [H.323] or [SIP].
F Enter the new password, and then
change the password, press
[Change] under Password (SID).
4
press [OK].
Changing a Registered IP-Fax
Destination
G Press [OK].
A Press the {User Tools / Counter}} key.
B Press [System Settings].
C Press [Administrator Tools], and then
To change the SEP Code
press [T
TNext].
D Press [Address Book Management].
E Select the name whose IP-Fax
A Press [Adv. Features].
B Press [SEP Code].
C Press [Change] under RX SEP Code.
D Enter the new SEP Code, and then
press [OK].
destination you want to change.
Press the name key, or enter the
registered number using the number keys.
E To
Note
❒ If you press , you can search
for a user by the registered
name, user code, fax number,
folder name, e-mail address, or
IP-Fax destination.
G Press [OK].
❒ To change the name, key display and title, see p.73 “Changing a Registered Name”.
change the password, press
[Change] under Password (PWD).
F Enter the new password, and then
press [OK].
To change the protocol
A Select [H.323] or [SIP].
F Press [Fax Dest.].
G Press [IP-Fax].
H Change the settings.
85
JupiterC2_GSG_EN_Pre_FM.book Page 86 Tuesday, December 28, 2004 1:39 PM
User Tools (System Settings)
E-mail Destination
Register e-mail destinations so you
do not need to enter an e-mail address
every time, and can send scan files
from scanner or fax function by email.
• It is easy to select the e-mail destination if you register “Name” and
“Key Display” as the e-mail destination.
• You can register e-mail destinations as a group.
• You can use the e-mail address as
the sender's address when sending
scan files in scanner mode. If you
want to do this, set a protection
code on the sender address to prevent unauthorized access. See
p.101 “Registering a Protection
Code”.
4
Note
❒ You can select an e-mail address
from an LDAP server, and then
register it in the Address Book.
“Sending Scan File by E-mail”,
Scanner Reference.
❒ You can set the machine to send a
transmission result e-mail whenever a user transmission is sent.
See Facsimile Reference <Advanced
Features>.
Registering an E-mail
Destination
A Press the {User Tools/Counter}} key.
B Press [System Settings].
C Press [Administrator Tools], and then
press [T
TNext].
D Press [Address Book Management].
E Select the name whose e-mail address you want to register.
Press the name key, or enter the
registered number using the number keys.
Note
❒ If you press , you can search
by the registered name, user
code, fax number, folder name,
e-mail address, or IP-Fax destination.
❒ To register the name, key display, and title, see p.73 “Registering a Name”.
F Press [E-mail].
86
JupiterC2_GSG_EN_Pre_FM.book Page 87 Tuesday, December 28, 2004 1:39 PM
E-mail Destination
G Press [Change] under E-mail Address.
H Enter the e-mail address, and then
press [OK].
Entering the e-mail address
A Enter the e-mail address.
B Press [OK].
Using the e-mail address as the
sender
When an e-mail address is entered,
it can be used as the sender's address.
A Press [Protection].
B Press [Sender] on the right side
of Use Name as.
Changing a Registered E-mail
Destination
A Press the {User Tools/Counter}} key.
B Press [System Settings].
C Press [Administrator Tools], and then
press [T
TNext].
D Press [Address Book Management].
E Select the name whose e-mail address you want to change.
Press the name key, or enter the
registered number using the number keys.
4
Note
❒ If you press , you can search
by the registered name, user
code, fax number, folder name,
e-mail address, or IP-Fax destination.
❒ To change the name, key display, and title, see p.73 “Changing a Registered Name”.
F Press [E-mail].
G Press [Change] under E-mail Address.
Reference
p.101 “Registering a Protection Code”
C Press [OK].
I Press [Exit].
J Press the {User Tools/Counter}} key.
Note
❒ When a group is registered, you
can add the e-mail destinations
to the group. See p.96 “Registering Names to a Group”.
H Enter the e-mail address, and then
press [OK].
Reference
p.159 “Entering Text”
I Press [OK].
J Press [Exit].
K Press the {User Tools/Counter}} key.
87
JupiterC2_GSG_EN_Pre_FM.book Page 88 Tuesday, December 28, 2004 1:39 PM
User Tools (System Settings)
Deleting a Registered E-mail
Destination
To delete a name entirely, see p.74
“Deleting a Registered Name”.
A Press the {User Tools/Counter}} key.
B Press [System Settings].
C Press [Administrator Tools], and then
press [T
TNext].
D Press [Address Book Management].
E Select the name whose e-mail ad-
4
dress you want to delete.
Press the name key, or enter the
registered number using the number keys.
Note
❒ If you press , you can search
by the registered name, user
code, fax number, folder name,
e-mail address, or IP-Fax destination.
❒ To delete the name, key display,
and title, see p.74 “Deleting a
Registered Name”.
F Press [E-mail].
G Press [Change] under E-mail Address.
H Press
[Delete All], and then press
[OK].
I Press [OK].
J Press [Exit].
K Press the {User Tools/Counter}} key.
88
JupiterC2_GSG_EN_Pre_FM.book Page 89 Tuesday, December 28, 2004 1:39 PM
Registering Folders
Registering Folders
By registering a shared folder, you
can send scan files to it directly.
There are two types of protocol you
can use:
• SMB
For sending files to shared Windows folders
• FTP
Use when sending files to an FTP
server.
Note
❒ For details about protocols, server
names, and folder levels, consult
your network administrator.
❒ You can prevent unauthorized users from accessing folders from the
machine. See p.101 “Registering a
Protection Code”.
❒ You can only select either SMB or
FTP. If you change protocol after
finishing your settings, all previous entries are cleared.
Reference
For details about network settings,
see “Setting Up the Machine on a
Network”, Network Guide.
For details about Scan to Folder,
see "Sending Scan Files by Scan to
Folder" Scanner Reference.
Using SMB to Connect
Note
❒ To register a folder in an FTP server, see p.93 “Using FTP to Connect”.
To register an SMB folder
A Press the {User Tools/Counter}} key.
4
B Press [System Settings].
C Press [Administrator Tools], and then
press [T
TNext].
D Press [Address Book Management].
E Select the name whose folder you
want to register.
Press the name key, or enter the
registered number using the number keys.
Note
❒ If you press , you can search
by the registered name, user
code, fax number, folder name,
e-mail address, or IP-Fax destination.
❒ To register the name, key display, and title, see p.73 “Registering a Name”.
89
JupiterC2_GSG_EN_Pre_FM.book Page 90 Tuesday, December 28, 2004 1:39 PM
User Tools (System Settings)
F Press [Auth. Info], and then press
[T
TNext].
G Press
[Specify Other Auth. Info] on
the right side of Folder Authentication.
Note
❒ When [Do not Specify] is selected,
the SMB User Name and SMB
Password that you have specified in Default User Name /
Password (Send) of File Transfer settings applies. For details,
see "User Tools Menu (System
Settings)", Network Guide.
4
H Press [Change] under Login User
Name.
I Enter
the login user name, and
then press [OK].
Note
❒ You can enter up to 128 characters for the user name.
Reference
p.159 “Entering Text”
J Press [Change] under Login Password.
K Enter
the password, and then
press [OK].
Note
❒ You can enter up to 128 characters for the password.
L Enter the password again to confirm, and then press [OK].
M Press [Folder].
N Confirm that [SMB] is selected.
90
Note
❒ To specify a folder, you can either enter the path manually or
locate the folder by browsing
the network.
Reference
p.90 “To locate the folder manually”
p.90 “Using Browse Network to
locate the folder”
To locate the folder manually
A Press [Change] under Path.
B Enter the path where the folder
is located.
Note
❒ Enter the path using this format: “\\ServerName\ShareName\PathName”.
❒ You can also enter an IP address.
❒ You can enter a path using
up to 128 characters.
C Press [OK].
Note
❒ If the format of the entered
path is not correct, a message
appears. Press [Exit], and
then enter the path again.
Using Browse Network to locate
the folder
A Press [Browse Network].
The client computers sharing
the same network as the machine appear.
JupiterC2_GSG_EN_Pre_FM.book Page 91 Tuesday, December 28, 2004 1:39 PM
Registering Folders
Note
❒ If you have already specified
your user name and password in steps F to L , the
Browse Network display
only lists client computers
you are authorized to access.
B Select a client computer.
Shared folders under it appear.
Note
❒ You can press [Up One Level]
to switch between levels.
C Select the folder you want to
register.
The Logon display appears.
Note
❒ If you have already entered
an authorized user name and
password, the Logon display
will not appear. Proceed to
step F.
D Enter the user name.
Note
❒ This is a user name which is
authorized to access the folder.
E Enter the user's password, and
then press [OK].
The Browse Network display
reappears.
Note
❒ If the entered user name or
password is not correct, a
message appears. Press [Exit],
and then enter the user name
and password again.
F Press [OK].
O Press [Connection Test] to check the
path is set correctly.
P Press [Exit].
Note
❒ If the connection test fails, check
the settings, and then try again.
Q Press [OK].
R Press [Exit].
S Press the {User Tools/Counter}} key.
4
Changing a registered folder
A Press the {User Tools/Counter}} key.
B Press [System Settings].
C Press [Administrator Tools], and then
press [T
TNext].
D Press [Address Book Management].
E Select the name whose folder you
want to change.
Press the user name key, or enter
the registered number using the
number keys.
Note
❒ If you press , you can search
by the registered name, user
code, fax number, folder name,
e-mail address, IP-Fax destination.
❒ To change the name, key display, and title, see p.73 “Changing a Registered Name”.
F Press [Folder].
91
JupiterC2_GSG_EN_Pre_FM.book Page 92 Tuesday, December 28, 2004 1:39 PM
User Tools (System Settings)
G Select the items you want to change.
To change the protocol
K Press [Exit].
L Press the {User Tools/Counter}} key.
A Press [FTP].
Deleting a registered folder
Note
❒ To delete a name entirely, see p.74
“Deleting a Registered Name”.
B A confirmation message appears.
Press [Yes].
4
Note
❒ Changing the protocol will
clear all settings made under
the previous protocol.
C Enter each item again.
Reference
p.93 “To register an FTP folder”.
Changing items under SMB
A Press [Change] under Path.
B Enter the new path where the
folder is located, and then
press [OK].
Note
❒ You can also use Browse Network to specify a new folder.
For details, see p.90 “Using
Browse Network to locate
the folder”.
H Press [Connection Test] to check the
path is set correctly.
I Press [Exit].
Note
❒ If the connection test fails, check
the settings, and then try again.
J Press [OK].
92
A Press the {User Tools/Counter}} key.
B Press [System Settings].
C Press [Administrator Tools], and then
press [T
TNext].
D Press [Address Book Management].
E Select the name whose folder you
want to delete.
Press the name key, or enter the
registered number using the number keys.
Note
❒ If you press , you can search
by the registered name, user
code, fax number, folder name,
e-mail address, or IP-Fax destination.
❒ To delete the name, key display,
and title, see p.74 “Deleting a
Registered Name”.
F Press [Folder].
G Press the protocol
which is not
currently selected.
A confirmation message appears.
H Press [Yes].
I Press [OK].
J Press [Exit].
K Press the {User Tools/Counter}} key.
JupiterC2_GSG_EN_Pre_FM.book Page 93 Tuesday, December 28, 2004 1:39 PM
Registering Folders
Using FTP to Connect
Note
❒ To register a shared folder configured in Windows, see p.89 “Using
SMB to Connect”.
To register an FTP folder
A Press the {User Tools/Counter}} key.
G Press
[Specify Other Auth. Info] on
the right side of Folder Authentication.
Note
❒ When [Do not Specify] is selected,
the SMB User Name and SMB
Password that you have specified in Default User Name /
Password (Send) of File Transfer settings applies. For details,
see "User Tools Menu (System
Settings)", Network Guide.
H Press [Change] under Login User
4
Name.
B Press [System Settings].
I Enter
the login user name, and
then press [OK].
Note
❒ You can enter up to 128 characters for the user name.
C Press [Administrator Tools], and then
press [T
TNext].
D Press [Address Book Management].
E Select the name whose folder you
want to register.
Press the name key, or enter the
registered number using the number keys.
Note
❒ If you press , you can search
by the registered name, user
code, fax number, folder name,
e-mail address, or IP-Fax destination.
❒ To register the name, key display, and title, see p.73 “Registering a Name”.
Reference
p.159 “Entering Text”
J Press [Change] under Login Password.
K Enter the password, and then press
[OK].
Note
❒ You can enter up to 128 characters for the password.
L Enter the password again to confirm, and then press [OK].
M Press [Folder].
N Press [FTP].
F Press [Auth. Info], and then press
[T
TNext].
93
JupiterC2_GSG_EN_Pre_FM.book Page 94 Tuesday, December 28, 2004 1:39 PM
User Tools (System Settings)
O Press [Change] under Server Name.
V Press [OK].
W Press [Exit].
X Press the {User Tools/Counter}} key.
Changing a registered folder
P Enter the server name, and then
press [OK].
Note
❒ You can enter a server name using up to 64 characters.
Q Press [Change] under Path.
R Enter the path.
4
Note
❒ You can enter an absolute path,
using this format: “/user/home/username”; or a relative path, using this format:
“directory/sub-directory”.
❒ If you leave the path blank, the
login directory is assumed to be
the current working directory.
❒ You can also enter an IP address.
❒ You can enter a path using up to
128 characters.
S Press [OK].
Note
❒ To change the port number,
press [Change] under Port No..
Enter the port number using the
number keys, and then press [#].
❒ You can enter 1 to 65535.
A Press the {User Tools/Counter}} key.
B Press [System Settings].
C Press [Administrator Tools], and then
press [T
TNext].
D Press [Address Book Management].
E Select the name whose folder you
want to change.
Press the name key, or enter the
registered number using the number keys.
Note
❒ If you press , you can search
for a user by name/index, user
code, fax number, folder name,
e-mail address, or IP-Fax destination.
❒ To change the name, key display, and title, see p.73 “Changing a Registered Name”.
F Press [Folder].
G Select the items
you want to
change.
To change the protocol
A Press [SMB].
T Press [Connection Test] to check the
path is set correctly.
U Press [Exit].
94
Note
❒ If the connection test fails, check
the settings, and then try again.
B A confirmation message appears.
Press [Yes].
JupiterC2_GSG_EN_Pre_FM.book Page 95 Tuesday, December 28, 2004 1:39 PM
Registering Folders
Note
❒ Changing the protocol will
clear all settings made under
the previous protocol.
C Enter each item again.
Reference
p.89 “To register an SMB
folder”.
Changing items under FTP
A Press [Change] under Port No.
B Enter the new port number,
and then press [#].
C Press [Change] under Server
Name.
D Enter the new server name, and
then press [OK].
E Press [Change] under Path.
F Enter the new path, and then
press [OK].
H Press [Connection Test] to check the
path is set correctly.
I Press [Exit].
Note
❒ If the connection test fails, check
the settings, and then try again.
J Press [OK].
K Press [Exit].
L Press the {User Tools/Counter}} key.
Deleting a registered folder
Note
❒ To delete a name entirely, see p.74
“Deleting a Registered Name”.
A Press the {User Tools/Counter}} key.
B Press [System Settings].
C Press [Administrator Tools], and then
press [T
TNext].
D Press [Address Book Management].
E Select the name whose folder you
4
want to delete.
Press the name key, or enter the
registered number using the number keys.
Note
❒ If you press , you can search
by the registered name, user
code, fax number, folder name,
e-mail address, or IP-Fax destination.
❒ To delete the name, key display,
and title, see p.74 “Deleting a
Registered Name”.
F Press [Folder].
G Press the protocol
which is not
currently selected.
A confirmation message appears.
H Press [Yes].
I Press [OK].
J Press [Exit].
K Press the {User Tools/Counter}} key.
95
JupiterC2_GSG_EN_Pre_FM.book Page 96 Tuesday, December 28, 2004 1:39 PM
User Tools (System Settings)
Registering Names to a Group
You can register names to a group to
enable easy management of e-mail
addresses and folders for each group.
To add names to a group, the groups
must be registered beforehand.
Note
❒ You can register up to 100 groups.
❒ When using Scan to Folder function, you cannot send scan files to a
group with over 50 folders registered.
❒ You can set a protection code to
prevent unauthorized access to the
folders registered in a group. For
details, see p.101 “Registering a
Protection Code”.
4
Registering a New Group
A Press the {User Tools/Counter}} key.
B Press [System Settings].
F Press [Change] under Group Name.
G Enter the group name, and then
press [OK].
The Key Display name is set automatically.
Reference
p.159 “Entering Text”
H Press the title key under Select Title, if necessary.
Note
❒ The keys you can select are as
follows:
• [Freq.]… Added to the page
that is displayed first.
• [AB], [CD], [EF], [GH], [IJK],
[LMN], [OPQ], [RST], [UVW],
[XYZ], [1] to [10]… Added to
the list of items in the selected title.
❒ You can select [Freq.] and one
more page for each title.
I When you want to change the key
C Press [Administrator Tools], and then
press [T
TNext].
D Press [Address Book: Program / Change /
Delete Group].
E Press [New Program].
96
display, press [Change] under Key
Display. Enter the key display,
and then press [OK].
J Press [OK].
K Press [Exit].
L Press the {User Tools/Counter}} key.
JupiterC2_GSG_EN_Pre_FM.book Page 97 Tuesday, December 28, 2004 1:39 PM
Registering Names to a Group
Registering Names to a Group
You can put names that have been
registered in the Address Book into a
group.
When registering new names, you
can also register groups at the same
time.
The group key that you have selected becomes highlighted, and
the name is added to it.
A Press the {User Tools/Counter}} key.
B Press [System Settings].
C Press [Administrator Tools], and then
H Press [OK].
I Press [Exit].
J Press the {User Tools/Counter}} key.
D Press [Address Book Management].
E Select the name to register in a
Displaying Names Registered
in Groups
press [T
TNext].
group.
Press the name key, or enter the
registered number using the number keys.
Note
❒ If you press , you can search
by the registered name, user
code, fax number, folder name
e-mail address, or IP-Fax destination.
F Press [Add to Group].
G Select a group to which you want
to add the name to.
4
You can check the names or groups
registered in each group.
A Press the {User Tools/Counter}} key.
B Press [System Settings].
C Press [Administrator Tools], and then
press [T
TNext].
D Press [Address Book: Program / Change /
Delete Group].
E Select the group where the mem-
bers you want to check is registered.
F Press [Programd. User/Group].
All the names registered will be
displayed.
Note
❒ If you press , you can search
for a group by entering the
group name.
G Press [OK].
H Press [Exit].
I Press the {User Tools/Counter}} key.
97
JupiterC2_GSG_EN_Pre_FM.book Page 98 Tuesday, December 28, 2004 1:39 PM
User Tools (System Settings)
Removing a Name from a
Group
A Press the {User Tools/Counter}} key.
B Press [System Settings].
C Press [Administrator Tools], and then
press [T
TNext].
D Press [Address Book Management].
E Select the name to remove from a
group.
Press the name key, or enter the
registered number using the number keys.
4
F Press [Add to Group].
G Select the group from which you
want to remove the name.
Note
❒ Highlighted keys indicate groups
in which the name has been registered.
The name is removed from the
group.
Changing a Group Name
A Press the {User Tools/Counter}} key.
B Press [System Settings].
C Press [Administrator Tools], and then
press [T
TNext].
D Press [Address Book: Program / Change /
Delete Group].
E Press the group key you want to
change.
F Enter the items.
To change the group name and
key display
A Press [Change] under Group
Name or Key Display.
B Enter the new group name or
key display, and then press
[OK].
To change the title
A Press the title key under Select
Title.
To change the registration
number
H Press [OK].
I Press [Exit].
J Press the {User Tools/Counter}} key.
A Press [Change] under Registration No..
B Enter the new registration number using the number keys
C Press [#].
G Press [OK].
98
JupiterC2_GSG_EN_Pre_FM.book Page 99 Tuesday, December 28, 2004 1:39 PM
Registering Names to a Group
H Press [Exit].
I Press the {User Tools/Counter}} key.
G Select the group which you want
to add to.
Deleting a Group
A Press the {User Tools/Counter}} key.
B Press [System Settings].
C Press [Administrator Tools], and then
The group key that you have selected becomes highlighted, and
the group is added to it.
press [T
TNext].
D Press [Address Book: Program / Change /
4
Delete Group].
E Press [Delete].
F Press a group key you want to delete.
G Press [Yes].
H Press [Exit].
I Press the {User Tools/Counter}} key.
Adding a Group to Another
Group
You can add a group to another
group.
A Press the {User Tools/Counter}} key.
B Press [System Settings].
C Press [Administrator Tools], and then
press [T
TNext].
D Press [Address Book: Program / Change /
Delete Group].
E Select the group that you want to
put into another group.
Press the group key, or enter the
registered number using the number keys.
F Press [Add to Group].
H Press [OK].
I Press [Exit].
J Press the {User Tools/Counter}} key.
Deleting a Group within a
Group
A Press the {User Tools/Counter}} key.
B Press [System Settings].
C Press [Administrator Tools], and then
press [T
TNext].
D Press [Address Book: Program / Change /
Delete Group].
E Select the group you want to de-
lete.
Press the group key, or enter the
registered number during the
number keys.
F Press [Add to Group].
The keys of groups in which the
group is registered appear highlighted.
99
JupiterC2_GSG_EN_Pre_FM.book Page 100 Tuesday, December 28, 2004 1:39 PM
User Tools (System Settings)
G Select the group that you want to
delete from.
H Press [OK].
4
The group key is deselected and
the group is deleted from it.
100
JupiterC2_GSG_EN_Pre_FM.book Page 101 Tuesday, December 28, 2004 1:39 PM
Registering a Protection Code
Registering a Protection Code
You can stop sender's names or folders being accessed by setting a protection code.
You can use this function to protect
the following:
• Folders
You can prevent unauthorized access to folders.
• Sender's names (when sending emails)
You can prevent misuse of sender's
names.
Note
❒ This function is not available
when using Internet Fax to send
e-mails.
Registering a Protection Code
To a Single User
A Press the {User Tools/Counter}} key.
Note
❒ If you press , you can search
by the registered name, user
code, fax number, folder name,
e-mail address, or IP-Fax destination.
❒ To register the name, key display, and title, see p.73 “Registering a Name”.
F Press [Protection].
G Press [Destination]
4
or [Sender] un-
der Use Name as.
Note
❒ Both [Destination] and [Sender]
can be selected at the same time.
To set the protection code
B Press [System Settings].
C Press [Administrator Tools], and then
press [T
TNext].
D Press [Address Book Management].
E Select the name whose protection
code you want to register.
Press the name key, or enter the
registered number using the number keys.
A Press [Change] under Protection
Code.
B Enter a protection code using
the number keys, and then
press [#].
Note
❒ You can enter up to eight
digits.
To specify the object of protection
A Press [Folder Destination] or [Sender] under Protection Object.
Note
❒ Both [Folder Destination] and
[Sender] can be selected at the
same time.
101
JupiterC2_GSG_EN_Pre_FM.book Page 102 Tuesday, December 28, 2004 1:39 PM
User Tools (System Settings)
H Press [OK].
I Press [Exit].
J Press the {User Tools/Counter}} key.
Registering a Protection Code
To a Group User
A Press the {User Tools/Counter}} key.
B Press [System Settings].
C Press [Administrator Tools], and then
4
press [T
TNext].
D Press [Address Book: Program / Change /
Delete Group].
E Press the group key you want to
register or enter the registered
number using the number keys.
F Press [Protection].
G Press [Folder Destination] under Protection Object.
H Press
[Change] under Protection
Code.
I Enter a protection code using the
number keys, and then press [#].
Note
❒ You can enter up to eight digits.
J Press [OK].
K Press [Exit].
L Press the {User Tools/Counter}} key.
102
JupiterC2_GSG_EN_Pre_FM.book Page 103 Tuesday, December 28, 2004 1:39 PM
Registering the Transfer Request
Registering the Transfer Request
This section describes how to register
the Transfer Station and Receiving
Station used in the fax function's
Transfer Request.
Note
❒ Before you can use Transfer Request, you must program the Polling ID and set the Transfer Report.
S e e “P ro g ra m m i n g a P o l lin g
ID”and “Transfer Report”, Facsimile Reference <Advanced Features>.
❖ Transfer Station
Refers to the machine that receives
the Transfer Request to forward incoming messages to another destination.
❒ You can have up to 30 Receiving
Stations per Transfer Station. If
you specify a Transfer Station
Group, the group counts as a single receiver.
Registering a Transfer
Station/Receiving Station
A Press the {User Tools/Counter}} key.
4
B Press [System Settings].
❖ Receiving Station
Refers to the facsimile or computer
that receives messages from the
Transfer Station.
Limitation
❒ When messages are transferred by
fax, Transfer Stations must be machines of the same manufacturer as
this one, and have the Transfer Station function.
❒ When messages are transferred by
e-mail, Transfer Stations must be
machines of the same manufacturer as this one, and have both the
Transfer Station and Internet Fax
functions.
❒ You cannot use Transfer Request
without programming the fax
number or e-mail address of the
Requesting Party in the Address
Book of the Transfer Stations.
Note
❒ Polling IDs of the Requesting Party
(this machine) and Transfer Stations must be identical.
C Press [Administrator Tools], and then
press [T
TNext].
D Press [Address Book: Program / Change /
Delete Transfer Request].
E Press [New Program].
F Set the Transfer Request's information.
To register the Transfer Request
name and key display
A Press [Change] under Transfer
Request Name or Key Display.
The name entry display appears.
B Enter the Transfer Request name
or key display, and then press
[OK].
103
JupiterC2_GSG_EN_Pre_FM.book Page 104 Tuesday, December 28, 2004 1:39 PM
User Tools (System Settings)
Reference
p.159 “Entering Text”
To select the title
A To associate a Transfer Request
name with a title, press the title
key under Select Title.
4
Note
❒ The keys you can select are as
follows:
• [Freq.]… Added to the
page that is displayed
first.
• [AB], [CD], [EF], [GH], [IJK],
[LMN], [OPQ], [RST], [UVW],
[XYZ], [1] to [10]… Added
to the list of items in the
selected title.
❒ You can select [Freq.] and one
more page for each title.
G Press [Fax Dest.].
H Enter the items. See p.80 “Registering a Fax Destination”.
I Press [E-mail].
J Enter the items. See p.86 “Registering an E-mail Destination”.
K Press [Receiving Statn.].
L Specify the Receiving Stations.
Note
❒ When specifying the Receiving
Stations, use the numbers
stored in Quick Dial keys, or
Groups in the Transfer Station.
104
Quick Dial
A Press [q
qQuick Dial].
B Enter the number stored in the
Quick Dial of the Transfer Station using the number keys.
For example, to select the destination stored in Quick Dial 01 of
th e Trans fer St ation , ent er
{0}
}{1}
}.
C To specify an additional Receiving Station, press [Add].
Speed Dial
A Press [q
qpSpeed Dial].
B Enter the Speed Dial number
using the number keys.
For example, to select the destination stored in Speed Dial 12 of
th e Trans fer St ation , ent er
{1}
}{2}
}.
C To specify an additional Receiving Station, press [Add].
Group Dial
A Press [q
qppGroup Dial].
B Enter the Group number using
the number keys.
For example, to select the destinations stored in Group 04 of
th e Trans fer St ation , ent er
{0}
}{4}
}.
C To specify an additional Receiving Station, press [Add].
M When you have specified all the
Receiving Stations, press [OK].
N Press [Exit].
O Press the {User Tools/Counter}} key.
JupiterC2_GSG_EN_Pre_FM.book Page 105 Tuesday, December 28, 2004 1:39 PM
Registering the Transfer Request
Changing a Registered
Transfer Station/Receiving
Station
A Press the {User Tools/Counter}} key.
B Press [System Settings].
C Press [Administrator Tools], and then
press [T
TNext].
D Press [Address Book: Program / Change /
Delete Transfer Request].
E Select the name whose Transfer
Station/Receiving Station you
want to change.
Press the name key, or enter the
registered number using the number keys.
Note
❒ If you press , you can search
by the group name, fax number,
e-mail address, or IP-Fax destination.
❒ To change the name, key display, and title, see p.73 “Changing a Registered Name”.
Note
❒ If you press , you can search
for a user by Transfer Request
name, fax number, or e-mail address.
F Enter the items.
To change the Transfer Request
name and key display
A Press [Change] under Transfer
Request Name or Key Display.
B Enter the new Transfer Request Name or key display,
and then press [OK].
To change the title
A Press the title key under Select
Title.
To change the Fax Station
A Press [Fax Dest.].
Proceed to step A of “To
change the E-mail Transfer Station” when messages are transferred by e-mail.
B Change the Transfer Station's
information. See p.82 “Changing a Registered Fax Destination”.
4
To change the E-mail Transfer
Station
A Press [E-mail].
B Change the Transfer Station's
information. See p.87 “Changing a Registered E-mail Destination”.
To change the Receiving Station
A Press [Receiving Statn.].
B Select the Receiving Station
you want to change.
C Press [Clear] to clear the number, and then enter the new
number us ing the number
keys.
G Press [OK].
H Press [Exit].
I Press the {User Tools/Counter}} key.
105
JupiterC2_GSG_EN_Pre_FM.book Page 106 Tuesday, December 28, 2004 1:39 PM
User Tools (System Settings)
Deleting a Registered Transfer
Station/Receiving Station
A Press the {User Tools/Counter}} key.
B Press [System Settings].
C Press [Administrator Tools], and then
press [T
TNext].
D Press [Address Book: Program / Change /
Delete Transfer Request].
E Press [Delete].
F Select the name whose Transfer
4
Station/Receiving Station you
want to delete.
Press the name key, or enter the
registered number using the number keys.
Note
❒ If you press , you can search
by the group name, fax number,
e-mail address, or IP-Fax destination.
❒ To delete the name, key display,
and title, see p.74 “Deleting a
Registered Name”.
G Press [Yes].
H Press [Exit].
I Press the {User Tools/Counter}} key.
106
JupiterC2_GSG_EN_Pre_FM.book Page 107 Tuesday, December 28, 2004 1:39 PM
Registering SMTP and LDAP Authentication
Registering SMTP and LDAP Authentication
SMTP Authentication
For each user registered in the Address Book, you can register a login
password to be used when accessing
an SMTP server.
Reference
To use an SMTP server, you need
to program it beforehand. For details, see "SMTP Server Settings",
Network Guide.
Note
❒ When [Do not Specify] is selected for
SMTP Authentication, the User
Name and Password that you have
specified in SMTP Authentication
of File Transfer settings applies.
For details, see "User Tools Menu
(System Settings)", Network Guide.
A Press the {User Tools/Counter}} key.
B Press [System Settings].
Note
❒ To register a name in the Address Book, see p.73 “Registering a Name”.
F Press [Auth. Info]
G Press [Specify Other Auth. Info]
on
the right side of SMTP Authentication.
H Press [Change] under Login User
4
Name.
I Enter the Login User Name, and
the press [OK].
Note
❒ You can enter up to 191 characters for the user name.
❒ When using POP before SMTP
Authentication, you can enter
up to 63 alphanumeric characters.
Reference
p.159 “Entering Text”
J Press [Change] under Login Password.
C Press [Administrator Tools], and then
press [T
TNext].
D Press [Address Book Management].
E Press the name you want to register or enter the registered number
using the number keys.
K Enter
the password, and then
press [OK].
Note
❒ You can enter up to 64 characters for the password.
L Enter the password again to confirm, and then press [OK].
M Press [OK].
107
JupiterC2_GSG_EN_Pre_FM.book Page 108 Tuesday, December 28, 2004 1:39 PM
User Tools (System Settings)
Note
❒ To change the SMTP Authentication settings, repeat steps H to
M.
LDAP Authentication
For each user registered in the Address Book, you can register a login
user name and login password to be
used when accessing an LDAP server.
Reference
To use an LDAP server, you need
to program it beforehand. For details, see “LDAP Server Settings”,
Network Guide.
4
Note
❒ When [Do not Specify] is selected for
LDAP Authentication, the User
Name and Password that you have
specified in Program/Change
LDAP Server of Administrator
Tools settings applies. For details,
see “Program/Change/Delete
LDAP Server”, Network Guide.
A Press the {User Tools/Counter}} key.
Note
❒ To register a name in the Address Book, see p.73 “Registering a Name”.
F Press [Auth. Info], and then press
[T
TNext].
G Press
[Specify Other Auth. Info] on
the right side of LDAP Authentication.
H Press [Change] under Login User
Name.
I Enter
the login user name, and
then press [OK].
Note
❒ You can enter up to 128 characters for the user name.
Reference
p.159 “Entering Text”
J Press [Change] under Login Password.
K Enter
B Press [System Settings].
the password, and then
press [OK].
Note
❒ You can enter up to 128 characters for the password.
L Enter the password again to confirm, and then press [OK].
C Press [Administrator Tools], and then
press [T
TNext].
D Press [Address Book Management].
E Press the name you want to regis108
ter or enter the registered number
using the number keys
M Press [OK].
Note
❒ To change the LDAP Authentication settings, repeat steps H to
M.
JupiterC2_GSG_EN_Pre_FM.book Page 109 Tuesday, December 28, 2004 1:39 PM
5. Troubleshooting
If Your Machine Does Not Operate As You
Want
The following chart contains explanations of common problems and messages.
If other messages appear, follow the instructions displayed.
Note
❒ If you cannot make copies as you want because of the paper type, paper size
or paper capacity problems, use recommended paper. See p.173 “Copy Paper”.
General
Problem
Causes
“Please wait. ” appears
If the power does not come on even
This message appears
when you turn on the oper- after 2 minutes have elapsed, conation switch or change the tact your service representative.
toner bottle.
Solutions
The display is off.
The screen contrast knob is Set the screen contrast knob to the
turned to the dark position. light position to see the display panel properly.
The machine is in Energy
Saver mode.
} key to canPress the {Energy Saver}
cel Energy Saver mode.
The operation switch is
turned off.
Turn on the operation switch.
Nothing happens when the
operation switch is turned
on.
The main power switch is
turned off.
Turn on the main power switch.
Memory is full.
There are too many
scanned pages or stored
files: hard disk capacity is
exceeded.
Press [Delete File] to delete unnecessary documents.
The function status indicator is red.
The function associated
with the red indicator was
interrupted.
Press the function key corresponding to the indicator. Follow the instructions that appear on the control
panel.
109
JupiterC2_GSG_EN_Pre_FM.book Page 110 Tuesday, December 28, 2004 1:39 PM
Troubleshooting
Problem
Causes
The main power indicator
continues blinking and
does not turn off when
pressed.
This occurs in the following cases:
Solutions
Close the exposure glass cover or
ADF, and check if the machine com• The exposure glass cov- municating with a computer.
er or the ADF is open.
• The machine is communicating with external
equipment.
• The hard disk is active.
5
“Self Checking... ”
appears.
The machine is preforming
image adjustment operations.
The machine may perform periodic
maintenance during operations. The
frequency and duration of maintenance depends on the humidity,
temperature, and printing factors
such as number of prints, paper
size, and paper type. Wait for the
machine to get ready.
Original images are printed on the reverse side of
the paper.
You may have loaded the
paper incorrectly.
Load paper correctly. Load paper
into Tray 1-4 with the print side up,
and into the LCT or bypass tray
with the print side down. See p.115
“Orientation-Fixed Paper or TwoSided Paper”.
Misfeeds occur frequently.
The tray's side guides may
not be locked or may not be
set properly.
Check the side guides are locked
and set properly. See p.128 “Changing the Paper Size”.
The tray's end guide may
not be set properly.
Check the end guide is set properly.
See p.128 “Changing the Paper
Size”.
You may have loaded paper of a size not shown on
the paper size selector.
When using paper of a size that cannot be detected automatically, use
Tray Paper Settings to set the paper
size. See p.58 “Tray Paper Size:Tray
2–4” and p.173 “Copy Paper”.
An error message remains,
even if misfed paper is removed.
When a misfeed message
Clear misfed paper, and then open
appears, it remains until
and close the front cover. See p.119
you open and close the cov- “xClearing Misfeeds”.
er as required.
Cannot print in duplex
mode.
You cannot use paper in
the bypass tray for duplex
printing.
For duplex printing, select Tray 1-4
in copier mode or with the printer
driver.
[1 Sided Copy] is selected for
Paper Type: Tray 1-4.
Select [2 Sided Copy] for Paper Type:
Tray 1-4. See p.59 “Paper Type: Tray
1–4”
You forgot your user code.
The user code entry display appears.
110
—
Users are restricted by user
codes.
Contact the administrator.
Enter the user code (up to 8-digits),
and then press [#].
JupiterC2_GSG_EN_Pre_FM.book Page 111 Tuesday, December 28, 2004 1:39 PM
If Your Machine Does Not Operate As You Want
Problem
Causes
The Authentication screen
appears.
Basic Authentication, Win- Enter your login user name and user
dows Authentication, or
password. See p.26 “When the AuLDAP Authentication is
thentication Screen is displayed”.
set.
“You do not have
the privileges to
use this function.” is displayed.
The use of the function is
restricted to authenticated
users only.
Contact the administrator.
“You do not have
This user code is not allowed to use the function
selected.
Press the {Energy Saver}
} key. Confirm that the display goes off, and
then press the {Energy Saver}
} key
again. The display will return to the
user code entry display.
The entered login user
name or login password is
not correct.
Inquire the user administrator for
the correct login user name and login password.
The machine cannot perform authentication.
Contact the administrator.
You have tried to delete
Files can be deleted by the person
who created the file. To delete a file
which you are not authorized to delete, contact the person who created
the file.
the privileges to
use this function..” continues to be
displayed even though you
have entered a valid user
code.
Authentication has failed.
“Selected files
files without the authority
contain file(s)
that the user does to do so.
not have access
privileges to.
Please note that
only the files
with access privileges will be deleted.” is displayed.
Solutions
5
111
JupiterC2_GSG_EN_Pre_FM.book Page 112 Tuesday, December 28, 2004 1:39 PM
Troubleshooting
Document Server
Problem
Solutions
"Scanned pages exceeded
max. number. Do you want
to store the scanned pages as a file?" appears.
The number of scanned pages exceeds the capacity per
file of the Document Server.
You forgot your password.
Contact the administrator.
To store scanned pages as a file, press [Store File].
Scanned data is stored as a file in the Document Server.
If you do not want to store scanned pages, press [No].
Scanned data is deleted.
You cannot find out what is stored in Check the date or time column in the Document Server:
a file.
Select Files to Print display.
Check document content by printing it's first page. Press
the line of the document in the Document Server: Select
Files to Print display, and then press [Print 1st Page] followed by the {Start}
} key.
5
Memory frequently becomes full.
• Press [Delete File] to delete selected documents to increase available memory.
• Delete documents stored using the scanner function.
See Scanner Reference.
You want to check print quality before making a large print run.
Check print quality by printing out only the first set using the {Sample Copy}
} key.
"Original is being
The copier or scanner function is in use. To cancel a job
scanned by another func- in progress, first press [Exit], and then press the {Copy}}
key or {Scanner}
} key. Next, press the {Clear/Stop}
} key.
tion." appears.
When the message "[Stop] key was pressed.
Stop storing?" appears, press [Stop].
Maintenance
Problem
Causes
Solutions
"Used Toner Bottle
The waste toner bottle is
full and it is time to replace
it.
Check your maintenance service
contract.
Replacement
Used Toner Bottle
is full.
Please replace
Used Toner Bottle."appears.
112
JupiterC2_GSG_EN_Pre_FM.book Page 113 Tuesday, December 28, 2004 1:39 PM
BLoading Paper
BLoading Paper
Important
❒ Tray 1 and LCT use A4 Kpaper exclusively. Load only A4 paper at
all times.
❒ If you want to load Letter- sized
paper (8 1/2" × 11"K) paper in Tray
1 or LCT, contact your sales or service representative.
A Pull
out the paper tray until it
stops.
Reference
For paper types and sizes, see
p.173 “Copy Paper”.
To load paper in the bypass tray,
see “Copying from the Bypass
Tray”, Copy Reference.
Note
❒ Fan the paper before loading.
❒ Straighten curled or warped paper
before loading.
ZJKY270J
Note
❒ You can change the paper size,
see p.128 “Changing the Paper
Size”.
5
B Load paper into the tray with the
print side down.
Loading Paper into Paper
Trays and Paper Tray Unit
Tray 1 uses only A4Kpaper. If you
want to load 8 1/2" × 11"K, contact
your sales or service representative.
The position of the side and end
guides can be changed in tray 2, 1 tray
paper unit, and 2 tray paper unit. Paper of various sizes can then be loaded in them.
This section describes loading paper
in tray 2.
ZJKY290J
ADL027S
Important
❒ Do not stack paper over the limit mark.
C Push in the paper tray slowly until it stops.
If a tray is pushed forcefully, the
position of its side guide may shift.
If you load a paper size that is not
selected automatically, you will
need to specify the paper size with
the control panel.
113
JupiterC2_GSG_EN_Pre_FM.book Page 114 Tuesday, December 28, 2004 1:39 PM
Troubleshooting
The following paper sizes are not
selected automatically:
• B5 JISL
• 81/2"×14"L
• 81/2"×11"L
B With the print side down, align
all four sides of two paper stacks,
and then load them next to each
other in the tray. Each side has a
limit of 1,000 sheets.
Reference
p.129 “If you load a paper size
that is not selected automatically”.
Loading Paper into Large
Capacity Tray (optional)
ZDJY009J
LCT (optional) uses A4Kpaper exclusively. Only load A4Kpaper. If
you want to load 81/2"×11"K, contact
your sales or service representative.
5
A Pull out the LCT, slowly until it
stops.
Important
❒ Align the paper stacks and load
them against the left and right
walls, or a paper misfeed might
occur.
❒ Do not stack paper over the limit mark.
C Push the paper tray slowly in until it stops.
ZJKY300J
114
JupiterC2_GSG_EN_Pre_FM.book Page 115 Tuesday, December 28, 2004 1:39 PM
BLoading Paper
Orientation-Fixed Paper or Two-Sided Paper
Orientation-fixed (top to bottom) or two-sided paper (for example, letterhead
paper, punched paper, or copied paper) might not print correctly, depending on
how the originals and paper are placed. Select [Yes] in Letterhead Setting under
Copier/Document Server Features, and then place the original and paper as
shown below (see “Letterhead Setting” Copy Reference). When printing with the
printer function, placement orientation is the same.
5
AAE034S
115
JupiterC2_GSG_EN_Pre_FM.book Page 116 Tuesday, December 28, 2004 1:39 PM
Troubleshooting
DAdding Toner
When Dappears, it is time to add toner.
R WARNING:
• Do not incinerate used toner or toner containers. Toner dust might ignite when exposed to an open flame. Dispose of used toner containers
in accordance with local regulations.
R CAUTION:
• Keep toner (used or unused) and toner containers out of reach of children.
R CAUTION:
• If toner or used toner is inhaled, gargle with plenty of water and move into a
fresh air environment. Consult a doctor if necessary.
R CAUTION:
• If toner or used toner gets into your eyes, flush immediately with large
amounts of water. Consult a doctor if necessary.
5
R CAUTION:
• If toner or used toner is swallowed, dilute by drinking a large amount of water. Consult a doctor if necessary.
R CAUTION:
• Avoid getting toner on your clothes or skin when removing a paper jam or
replacing toner. If your skin comes into contact with toner, wash the affected
area thoroughly with soap and water.
• If toner gets on your clothing, wash with cold water. Hot water will set the
toner into the fabric and may make removing the stain impossible.
If the message "No toner: xxxx,xxxx" is shown on the display, replace the applicable color-toner.
Note
❒ "xxxx,xxxx" is shown as the color of toner is almost empty, and the combination of 1-4 of Yellow, Magenta, Cyan, and Black is displayed.
Important
❒ Fault may occur if you use toner other than the recommended type.
❒ When adding toner, do not turn off the operation switch. If you do, settings
will be lost.
❒ Always add toner when the machine instructs you.
116
JupiterC2_GSG_EN_Pre_FM.book Page 117 Tuesday, December 28, 2004 1:39 PM
DAdding Toner
Note
❒ The message “DToner is almost empty.” on the display shows a toner
name and the telephone number for ordering.
❒ The consumption of toner depends on the humidity, temperature and printing factors such as image size, density, number of prints, paper size, and paper type. Moreover, to preserve print quality, this machine automatically
performs periodic maintenance using the toner.
❒ Change all four color-toner cartridges in the same way.
Reference
For details about toner storage, see p.147 “Toner Storage”.
Inserting Toner
5
AFZ008S
117
JupiterC2_GSG_EN_Pre_FM.book Page 118 Tuesday, December 28, 2004 1:39 PM
Troubleshooting
When toner remains
Toner can remain inside the toner cartridge in certain environments. If this happens, set the toner cartridge again. Toner will be supplied automatically, and
you can then continue to use it.
5
118
JupiterC2_GSG_EN_Pre_FM.book Page 119 Tuesday, December 28, 2004 1:39 PM
xClearing Misfeeds
xClearing Misfeeds
R CAUTION:
• The fusing section of this machine might be very hot. Caution should be taken when removing misfed paper.
Important
❒ When clearing misfeeds, do not turn off the operation switch. If you do, your
copy settings will be lost.
❒ To prevent misfeeds, do not leave any torn scraps of paper inside the machine.
❒ If paper misfeeds occur frequently, contact your service representative.
Note
❒ More than one misfed area may be indicated. When this happens, check all
the areas indicated. See the following charts:
• A, B, Y, Z1⇒ p.120
• R (2 Tray Finisher)⇒ p.123
• R (Booklet Finisher)⇒ p.122
• P⇒ p.124
• Z2 ⇒ p.126
❒ Inside the finisher, or inside the front cover, there is a sticker explaining how
to remove misfed paper.
5
119
JupiterC2_GSG_EN_Pre_FM.book Page 120 Tuesday, December 28, 2004 1:39 PM
Troubleshooting
5
120
JupiterC2_GSG_EN_Pre_FM.book Page 121 Tuesday, December 28, 2004 1:39 PM
xClearing Misfeeds
5
AFZ009S
121
JupiterC2_GSG_EN_Pre_FM.book Page 122 Tuesday, December 28, 2004 1:39 PM
Troubleshooting
5
122
JupiterC2_GSG_EN_Pre_FM.book Page 123 Tuesday, December 28, 2004 1:39 PM
xClearing Misfeeds
5
AFZ010S
123
JupiterC2_GSG_EN_Pre_FM.book Page 124 Tuesday, December 28, 2004 1:39 PM
Troubleshooting
5
124
JupiterC2_GSG_EN_Pre_FM.book Page 125 Tuesday, December 28, 2004 1:39 PM
xClearing Misfeeds
5
AFZ011S
125
JupiterC2_GSG_EN_Pre_FM.book Page 126 Tuesday, December 28, 2004 1:39 PM
Troubleshooting
5
126
JupiterC2_GSG_EN_Pre_FM.book Page 127 Tuesday, December 28, 2004 1:39 PM
xClearing Misfeeds
5
AFZ012S
127
JupiterC2_GSG_EN_Pre_FM.book Page 128 Tuesday, December 28, 2004 1:39 PM
Troubleshooting
Changing the Paper Size
Preparation
Be sure to select the paper size
with User Tools and the paper size
selector. If you do not, misfeeds
might occur. See p.58 “Tray Paper
Size:Tray 2–4”.
Note
❒ Tray 1 and LCT (optional) use only
A4Kpaper. To load 8 1/2" × 11"K,
contact your service representative.
❒ Procedures for changing the paper
size differ depending on the tray
(tray 1 or other optional paper tray
units). Make sure you are following the appropriate procedure before you begin.
5
C Set
the paper guide lock to the
“unlocked" position.
ZJKY280J
D While pressing the release lever,
adjust the side guides to the paper
size.
Reference
For details about paper sizes and
types, see p.173 “Copy Paper”.
Changing the Paper Size of the
Paper Tray
ZDJY802J
A Make sure the paper tray is not in
use. Then, pull the paper tray out
slowly.
E Adjust the end guide to the paper
size.
ZHXH760J
ZJKY270J
B If paper is loaded in the tray, remove it.
128
JupiterC2_GSG_EN_Pre_FM.book Page 129 Tuesday, December 28, 2004 1:39 PM
Changing the Paper Size
F Square the paper, and then load it
in the tray with the copying face
down.
ZJKY290J
ADL027S
Important
❒ Do not stack paper over the limit mark.
❒ Check the top of the paper is
aligned to the right side.
Note
❒ If there is space between the
side guide and paper, bring the
side guide flush against the
edge of the paper.
If you load a paper size that is
not selected automatically
If you load a paper size that is not selected automatically, you need to
specify the paper size with the control
panel.
Following paper sizes that are not selected automatically.
• B5 JISL
• 8 1/2" × 14" L
• 8 1/2" × 11" L
A Press the {User Tools/Counter}} key.
5
B Press [System Settings].
G Lock the side guide.
C Press [Tray Paper Settings].
D Select the tray for which you want
ZKVH210J
H Gently push the paper tray in until it stops.
I Check
to change the paper settings.
Note
❒ Press either of [Tray Paper Size:
Tray 2] to [Tray Paper Size: Tray 4].
the paper size shown on
the display panel.
129
JupiterC2_GSG_EN_Pre_FM.book Page 130 Tuesday, December 28, 2004 1:39 PM
Troubleshooting
E Select the loaded paper size and
feed direction, and then press
[OK].
The set paper size and feed direction is displayed.
5
F Press the {User Tools/Counter}} key.
The initial display is shown.
Important
❒ If you want to print on paper
that is selected automatically after printing on a paper size that
is not selected automatically,
you must return the setting to
“Auto Detect”. Reload the paper, repeat step A to D, and select “Auto Detect" in step E. The
setting is returned to “Auto Detect”.
130
JupiterC2_GSG_EN_Pre_FM.book Page 131 Tuesday, December 28, 2004 1:39 PM
dAdding Staples
dAdding Staples
Important
❒ Stapling failures or jams may occur if you use a staple cartridge other than
that recommended.
Reference
For details about the type of finisher, see p.21 “External Options”.
2 Tray Finisher
5
AAE009S
131
JupiterC2_GSG_EN_Pre_FM.book Page 132 Tuesday, December 28, 2004 1:39 PM
Troubleshooting
Booklet Finisher
5
AFZ013S
132
JupiterC2_GSG_EN_Pre_FM.book Page 133 Tuesday, December 28, 2004 1:39 PM
Removing Jammed Staples
Removing Jammed Staples
Note
❒ Curled paper may cause staples to jam. To avoid this, turn copy paper over
in the tray. If there is no improvement, change to a stiffer copy paper.
❒ After removing jammed staples, staples will not be ejected the first few times
you try to use the stapler.
Reference
For types of finisher, see p.21 “External Options”.
2 Tray Finisher
5
AAE011S
133
JupiterC2_GSG_EN_Pre_FM.book Page 134 Tuesday, December 28, 2004 1:39 PM
Troubleshooting
Booklet Finisher
5
AFZ014S
134
JupiterC2_GSG_EN_Pre_FM.book Page 135 Tuesday, December 28, 2004 1:39 PM
yRemoving Punch Waste
yRemoving Punch Waste
Note
❒ While "Punch Receptacle Full"
is displayed, you cannot use the
Punch function.
C Reinstall the punch waste box.
2 Tray Finisher
A Open the front cover of the 2 tray
finisher.
ZDSO030J
Note
❒ If you do not, "Punch Receptacle Full " will remain displayed.
5
D Close the front cover of the 2 tray
ADL023S
B Pull out the punch waste box, and
then remove punch waste.
ZDSO020J
finisher.
"Punch Receptacle Full" disappears.
Note
❒ If the message is still displayed,
reinstall the punch waste box.
❒ The message "Punch Receptacle Full " may appear even
when the punch waste box is
not yet full. If this happens, the
position of the punch waste box
(in dic ated by the arrow as
shown) may be blocked by
punch waste. Remove the
punch waste.
ZHVP010J
135
JupiterC2_GSG_EN_Pre_FM.book Page 136 Tuesday, December 28, 2004 1:39 PM
Troubleshooting
Booklet Finisher
A Hold the release lever, and then
pull out the booklet finisher.
ZKVH220J
B Pull out the punch waste box, and
5
then remove the paper chips.
ZKVH180J
C Reinstall the punch waste box.
ZKVH190J
Note
❒ If the message does not disappear, reinstall the punch waste
box.
136
D Attach the booklet finisher.
JupiterC2_GSG_EN_Pre_FM.book Page 137 Tuesday, December 28, 2004 1:39 PM
Replacing the Stamp Cartridge
Replacing the Stamp Cartridge
When the stamp begins to fade, replace the cartridge.
Note
❒ This stamp cartridge is used for
facsimile and scanner functions.
C Pull out the old stamp cartridge.
Tap the cartridge lock lever several
times. The cartridge will eject.
Then remove the cartridge, while
pushing the lock lever.
❒ Use the cartridge specified for this
machine.
❒ Do not attempt to put ink into the
cartridge. Doing so will result in
leakage.
❒ Be sure not to dirty your fingers
with ink from the cartridge.
A Open the ADF unit.
5
ZDPH080J
D Insert the new stamp cartridge.
Insert the cartridge until the metal
parts are no longer visible.
ZEXH070J
B Open the stamp cover.
ZDPH090J
E Press the stamp cover back in until it clicks.
ZJFH010J
ZDPH100J
F Close the ADF unit.
137
JupiterC2_GSG_EN_Pre_FM.book Page 138 Tuesday, December 28, 2004 1:39 PM
Troubleshooting
Adjusting the Color Registration
When the machine is moved, the Fusing Unit is replaced, or after printing
repeatedly for some time, registration
shifting might occur. By performing
color registration adjustment, you
can maintain optimum print results.
Auto Color Registration
E Press [OK].
Auto color registration will be
started.
If the color documents show registration shifting, perform automatic color
registration.
A Press the {User Tools/Counter}} key.
5
B Press [Maintenance].
Auto color registration takes about
fifty seconds. When it is completed, the display returns to the color
registration menu.
F When you have made all the set-
}
tings, press the {User Tools/Counter}
key.
The initial display is shown.
C Press [Color Registration].
Fuser Adjustment for Thick
Paper
When color shifting occurs using thick
paper
D Press [Auto Color Registration].
Follow the procedure below if color
shifting occurs when you use the
thick paper of A4 size or larger.
Important
❒ When the toner cartridge is almost
empty, "Fuser Adjustment: Thick
Paper" is not available. Replace the
toner cartridge before the adjustment.
138
JupiterC2_GSG_EN_Pre_FM.book Page 139 Tuesday, December 28, 2004 1:39 PM
Adjusting the Color Registration
Note
❒ Thick paper is needed for the adjustment. Prepare thick paper similar to what you normally use.
Lor larger thick paA Load the A4L
per in the Bypass Tray.
Reference
For details about paper size and
the procedure for loading paper
in the Bypass tray, see “Copying from the Bypass tray”, Copy
Reference
Important
❒ When the toner cartridge is almost empty "Fuser Adjustment
cannot be performed. Replace
Toner cartridge." appears on the
panel display.
F Press [OK].
Auto Color Registration begins.
B Press the {User Tools/Counter}}key.
5
C Press [Maintenance].
D Press [Color Registration].
G Make
sure that following message appears on the display, and
then press [Start Printing].
Fuser Adjustment Sheet II is printing. See p.141 “Checking the Fuser
Adjustment Sheet”.
E Press [Fuser Adjustment: Thick Paper].
139
JupiterC2_GSG_EN_Pre_FM.book Page 140 Tuesday, December 28, 2004 1:39 PM
Troubleshooting
H Compare
the sample with the
printed pattern box at the bottom
of the Fuser Adjustment Sheet II.
Specify which square in the box
matches the sample.
If you specify “0”, setting is finished and the display that appeared in step returns.
If you specify “-1” or “+1”, the following display appears.
5
Press [Start Printing]. An adjusted
Fuser Adjustment Sheet II is printed and the display that appeared
in Step H reappears. Keep adjusting until the printed pattern looks
the same as the printed pattern,
and then specify “0”.
I After
making all the settings,
press the {User Tools/Counter}
} key.
The initial display is shown.
140
JupiterC2_GSG_EN_Pre_FM.book Page 141 Tuesday, December 28, 2004 1:39 PM
Adjusting the Color Registration
Checking the Fuser Adjustment Sheet
Following image is sample of the test sheet.
❖ Fuser Adjust Sheet II
5
141
JupiterC2_GSG_EN_Pre_FM.book Page 142 Tuesday, December 28, 2004 1:39 PM
Troubleshooting
Auto Color Calibration
If a certain color is strong or the color
of the copy differs from the original,
adjust the yellow, magenta, cyan and
black balance.
Note
❒ If "DToner is almost empty." is
shown on the display panel, the
test pattern cannot be printed.
A Press the {User Tools/Counter}} key.
5
B Press [Maintenance].
E Press [Start Printing] and a test pattern will be printed.
Note
❒ When performing the auto color
calibration from the printer
function, select test patterns
from [600 x 600 dpi], [1800×
× 600
dpi] and [1200 x 1200 dpi] and
then press [Start Printing].
❒ The test pattern will be printed
on an A4K, 81/2”× 11”K size
page (If A4K is not available
then A3 L, B4 JISL will be
used.). Make sure to check the
paper set in the paper tray.
❒ The counter will not proceed
when the test pattern is printed.
F Place the test pattern on the exposure glass and press [Start Scanning].
The image will be corrected after
"Please wait." disappears.
C Press [Auto Color Registration].
D Press [Start] on the “Copier Function”.
Note
❒ When performing the auto color
calibration from the copy function, press [Start] under Copier
Function. When performing
from the printer function, press
[Start] under Printer Function.
142
Note
❒ The test pattern will not be read
if it is set in the ADF.
❒ Set the test pattern in the following way:
GCCLCPIE
❒ When the ADF is installed, make
sure to set the test pattern on the
exposure glass, and then 2 or 3
white sheets, same size as the
test pattern, above the test pattern.
JupiterC2_GSG_EN_Pre_FM.book Page 143 Tuesday, December 28, 2004 1:39 PM
Adjusting the Color Registration
Returning to the previous setting
Note
❒ “Previous Setting” means to return to the previous status before any changes.
A Press [Previous Setting] in the
“Auto Color Calibration .
When returning the auto color
calibration of the copy function,
press [Previous Setting] of the
Copier Function. If returning
the auto color calibration of the
printer function, press [Previous
Setting] of the Printer Function.
5
B Press [Yes].
The settings return to the previous contents.
143
JupiterC2_GSG_EN_Pre_FM.book Page 144 Tuesday, December 28, 2004 1:39 PM
Troubleshooting
5
144
JupiterC2_GSG_EN_Pre_FM.book Page 145 Tuesday, December 28, 2004 1:39 PM
6. Remarks
Dos and Don'ts
R WARNING:
• Keep the machine away from
flammable liquids, gases, and
aerosols. A fire or an electric
shock might occur.
R CAUTION:
• Unplug the power cord from the
wall outlet before you move the
machine. While moving the machine, you should take care that
the power cord will not be damaged under the machine.
Important
❒ Do not turn the power off while
the On indicator is lit or blinking.
Doing so may damage the hard
disk.
❒ Before unplugging the power cord
or turning off the main power
sw itc h, m ake sure remaining
m e m ory space is at 100% , a s
shown on the display. See p.29
“Turning Off the Power” and p.29
“Turning Off the Main Power”.
• When you use this machine for a
long time in a confined space without good ventilation, you may detect an odd smell. To keep the
workplace comfortable, we recommend that you keep it well ventilated.
• Do not touch areas on or around
the fusing unit. These areas may
become hot.
• After scanning originals continuously, the exposure glass may become warm—this is not a
malfunction.
• The area around the ventilation
hole might feel warm. This is
caused by exhaust air and is not a
malfunction.
• When the machine is not in use
and in stand-by mode, you may
hear a small noise inside. This is
caused by the image stabilization
process and is not a malfunction.
• Do not turn off the power when
the machine is in operation.
• The machine might not produce
good copy images if condensation
forms inside as a result of rapid
temperature change.
• Do not open the covers of the machine when it is in operation. If you
do, misfeeds might occur.
• Do not move the machine when
the power is on.
• The machine might not produce
good copy images if condensation
forms inside as a result of rapid
temperature change. To avoid possible condensation, this machine is
equipped with anti-condensation
heaters. Even when the main power switch is off, the machine continues to maintain a stable
temperature when the anti-condensation heaters are on.
• If you operate the machine improperly or a machine failure occurs, settings might be lost. Be sure
to make a note of your machine
settings.
• The supplier shall not be liable for
any loss or damage resulting from
mechanical failure, loss of settings,
or use of the machine.
145
JupiterC2_GSG_EN_Pre_FM.book Page 146 Tuesday, December 28, 2004 1:39 PM
Remarks
Saving Color Copies
• There is no difference between color prints and color copies in terms of fading. However, for long-term storage, make sure to store them in a binder
away from direct sunlight.
• Toner may melt if a print and a half-dried print are put on top of each other.
• Toner may also melt when using solvent type adhesive agents for pasting
prints.
• When folding prints, toner in the folds will come off.
• Toner may melt if it is placed on mats made of chlorinated plastic in locations
of high temperature for long periods of time.
• Toner may melt if prints are placed in places of extremely high temperatures,
such as near heaters.
6
146
JupiterC2_GSG_EN_Pre_FM.book Page 147 Tuesday, December 28, 2004 1:39 PM
Toner
Toner
Handling Toner
R WARNING:
• Do not incinerate used toner or toner containers. Toner dust might ignite when exposed to an open flame. Dispose of used toner containers
in accordance with local regulations.
R CAUTION:
• Keep toner (used or unused) and toner containers out of reach of children.
Important
❒ Fault may occur if you use toner other than the recommended type.
Reference
To add toner, see p.116 “DAdding Toner”.
6
Toner Storage
When storing toner, the following precautions should always be followed:
• Store toner containers in a cool, dry place free from direct sunlight.
• Store on a flat surface.
Used Toner
Note
❒ Toner cannot be re-used.
147
JupiterC2_GSG_EN_Pre_FM.book Page 148 Tuesday, December 28, 2004 1:39 PM
Remarks
Where to Put Your Machine
Machine Environment
Environments to avoid
Choose your machine's location carefully. Environmental conditions
greatly affect its performance.
• Locations exposed to direct sunlight or other sources of strong
light (more than 1,500 lux).
• Locations directly exposed to cool
air from an air conditioner or heated air from a heater. (Sudden temperature changes can cause
condensation to form inside the
machine.)
• Locations close to machines generating ammonia, such as a diazo
copy machine.
• Places where the machine will be
subject to frequent strong vibration.
• Dusty areas.
• Areas with corrosive gases.
Optimum environmental conditions
R CAUTION:
• Keep the machine away from humidity and dust. Otherwise a fire
or an electric shock might occur.
• Do not place the machine on an
unstable or tilted surface. If it topples over, an injury might occur.
6
R CAUTION:
• If you use the machine in a confined space, make sure there is a
continuous air turnover.
• Temperature: 10-32 °C (50-89.6 °F)
(humidity to be 54% at 32 °C, 89.6 °F)
• Humidity: 15-80% (temperature to
be 27 °C, 80.6 °F at 80%)
• A strong and level base.
• The machine must be level within
5 mm, 0.2 inches: both front to rear
and left to right.
• To avoid possible buildup of ozone,
be sure to locate this machine in a
large well ventilated room that has
an air turnover of more than 30
m3/hr/person.
148
Moving
R CAUTION:
• Unplug the power cord from the
wall outlet before you move the
machine. While moving the machine, you should take care that
the power cord will not be damaged under the machine.
Important
❒ Be careful when moving the machine. Take the following precautions:
• Turn off the main power. See
p.29 “Turning Off the Main
Power”.
• Unplug the power cord from
the wall outlet. When you pull
out the plug from the socket,
grip the plug to avoid damaging the cord, thereby reducing
the risk of fire or electric shock.
JupiterC2_GSG_EN_Pre_FM.book Page 149 Tuesday, December 28, 2004 1:39 PM
Where to Put Your Machine
• Close all covers and trays, including the front cover and bypass tray.
❒ Move the machine carefully. If you
do not, it could result in damage
and stored files might be lost.
❒ Do not take off the holding stand.
❒ Protect the machine from strong
shocks. Impact can damage the
hard disk and cause stored files to
be lost. As a precautionary measure, files should be copied to another computer.
Power Connection
R WARNING:
• Connect the machine only to
the power source described
on the inside front cover of
this manual. Connect the power cord directly into a wall outlet and do not use an
extension cord.
• Do not damage, break or make
any modifications to the power cord. Do not place heavy
objects on it. Do not pull it
hard nor bend it more than
necessary. These actions
could cause an electric shock
or fire.
R CAUTION:
• Unplug the power cord from the
wall outlet before you move the
machine. While moving the machine, you should take care that
the power cord will not be damaged under the machine.
R CAUTION:
• When you disconnect the power
plug from the wall outlet, always
pull the plug (not the cable).
• When the main power switch is in
the stand-by position, the optional
anti-condensation heaters are on.
In an emergency, unplug the machine's power cord.
• When you unplug the power cord,
the anti-condensation heaters turn
off.
• Make sure the plug is inserted
firmly in the wall outlet.
• Voltage must not fluctuate by more
than 10%.
• The wall outlet shall be installed
near the machine and shall be easily accessible.
Access to the Machine
Place the machine near the power
source, providing the clearance areas
shown.
6
AAE004S
1. Rear: more than 10 cm (4")
2. Right: more than 55 cm (21.7")
3. Front: more than 70 cm (27.6")
4. Left: more than 46 cm (18.2")
Note
❒ For the required space when options are installed, contact your
service representative.
149
JupiterC2_GSG_EN_Pre_FM.book Page 150 Tuesday, December 28, 2004 1:39 PM
Remarks
Maintaining Your Machine
If the exposure glass, exposure glass
cover, or ADF belt is dirty, copy clarity may be reduced. Clean these parts
if they are dirty.
Cleaning the Exposure Glass
Cover
❖ Cleaning the machine
Wipe the machine with a soft,
damp cloth, and then wipe it with
a dry cloth to remove the water.
Important
❒ Do not use chemical cleaners or organic solvents, such as thinner or
benzene. If such substances get inside the machine or melt plastic
parts, a failure might occur.
❒ Do not clean parts other than those
explicitly specified in this manual.
Other parts should be cleaned only
by your service representative.
6
ZGJS826E
Cleaning the Auto Document
Feeder
Cleaning the Exposure Glass
2
1
GDSH130J
Clean 1 and 2.
GDSH050J
Clean 1 and 2.
150
JupiterC2_GSG_EN_Pre_FM.book Page 151 Tuesday, December 28, 2004 1:39 PM
Cleaning the Dustproof Glass
Cleaning the Dustproof Glass
The dustproof glass may require
cleaning if white lines appear on the
print side of the document.
A Turn
C Slide the cleaning brush in and
out slowly 2 to 3 times to clean all
four areas.
off the power switch, and
then unplug the power cable.
B Open the front cover and remove
the cleaning brush.
ZKVH260J
ZKVH240J
There are four holes for cleaning
the dustproof glass.
Important
❒ Do not insert the brush forcefully, or the machine might be
damaged.
6
D Return the cleaning brush to its
original position.
E Plug in the power cable, and then
turn on the power switch.
AFZ028S
151
JupiterC2_GSG_EN_Pre_FM.book Page 152 Tuesday, December 28, 2004 1:39 PM
Remarks
Earth Leakage Breaker
To prevent electric shock this machine has an earth leakage breaker.
The earth leakage breaker is normally
in the on position.
Once a month, check that it functions
properly by following the procedure
below.
D Using the tip of a ball-point pen,
press the test button of the earth
leakage breaker.
Important
❒ If the earth leakage breaker is not
functioning normally, contact your
sales or service representative.
A Make sure the exposure glass cover or the ADF is closed.
E Confirm
B Turn off the power.
Reference
⇒ p.29 “Turning Off the Power”, p.29 “Turning Off the Main
Power”
6
ADL010S
that the earth leakage
breaker switch moves to the off
position.
C If the finisher is installed, detach
it from the machine.
ADL012S
F Turn the
switch to the on posi-
tion.
ADL015S
Note
❒ The above illustration shows
the 2 tray finisher. If you are using the Booklet finisher, detach
it in the same way.
ADL013S
152
JupiterC2_GSG_EN_Pre_FM.book Page 153 Tuesday, December 28, 2004 1:39 PM
Earth Leakage Breaker
G If
the finisher is installed, reattach it to the machine.
ADL015S
Note
❒ The above illustration shows
the 2 tray finisher. If you are using the Booklet finisher, reattach it in the same way.
H Turn on the main power switch of
6
the machine.
Note
❒ If the power does not come on,
check if the earth leakage breaker is in the off position. If so, do
not turn it to the on position.
Contact your sales or service
representative immediately.
R WARNING:
• Do not turn the earth
leakage breaker
from the off to the on
position. Otherwise
it might lead to an
electric shock, fire
or smoke, or cause
the circuit breakers
to trip.
153
JupiterC2_GSG_EN_Pre_FM.book Page 154 Tuesday, December 28, 2004 1:39 PM
Remarks
Replacing the Waste Toner Bottle
C Take the new waste toner bottle
R WARNING:
• Do not incinerate spilled toner
or used toner. Toner dust
might ignite when exposed to
an open flame.
out of the bag.
R CAUTION:
• The inside of the machine becomes very hot. Do not touch the
parts with a label indicating a “hot
surface”. Otherwise, an injury
might occur.
ZDJH228J
• Keep toner (used or unused) and
the toner cartridge out of reach of
children.
D Slowly
If the message "Used Toner Bottle
Replacement", "Used Toner Bottle
is full. ", and " Please replace
Used Toner Bottle." are displayed,
either replace it on your own by following the procedure below or call
your service representative.
6
Note
❒ Service differ depending on the
maintenance service contract.
A Turn off the power, and then unplug the power cable.
B Slowly
open the front cover by
pulling down from the two areas
on the left and right.
remove the used waste
toner bottle from inside the machine.
AFZ015S
Important
❒ Be sure to remove the waste
toner bottle horizontally.
A), and then put
E Remove the lid (A
it in the position shown in the illustration (B
B).
AA
AFZ018S
ZDJH229J
154
JupiterC2_GSG_EN_Pre_FM.book Page 155 Tuesday, December 28, 2004 1:39 PM
Replacing the Waste Toner Bottle
F Put
the used waste toner bottle
into the bag that contained the
new waste toner bottle, and then
seal the bag.
I Slowly
close the front cover by
pushing the two areas on the left
and right.
Important
❒ Be sure to handle the bottle
carefully so waste toner does
not spill.
G Insert the new waste toner bottle
as shown.
AA
AFZ019S
J Plug in the power cable, and then
turn on the power.
6
AFZ016S
H Push it in until it stops.
AFZ017S
Important
❒ Be sure to firmly insert the
waste toner bottle to avoid toner leakage inside the machine.
155
JupiterC2_GSG_EN_Pre_FM.book Page 156 Tuesday, December 28, 2004 1:39 PM
Remarks
Other Functions
Inquiry
The inquiry function lets you check
the telephone numbers to contact for
repairs or ordering toner. Be sure to
contact your service engineer to verify the following:
❖ Consumables
• Telephone No. to order
• Toner
• Staple
• TX Stamp Name
6
Printing inquiry information
A Press [Print Inquiry List].
B Press the {Start}
} key.
Inquiry information is printed.
C Press [Exit].
D Press [Exit].
❖ Machine Maintenance/Repair
• Telephone No.
• Serial No. of Machine
Changing the Display
Language
❖ Sales Representative
• Telephone No.
You can change the language used on
the display. English is set as default.
A Press the {User Tools/Counter}} key.
A Press the {User Tools/Counter}} key.
B Press [Inquiry].
B Press [Español].
Inquiry information appears.
The language is changed to Spanish.
C Press [Exit].
The menu appears in Spanish.
156
JupiterC2_GSG_EN_Pre_FM.book Page 157 Tuesday, December 28, 2004 1:39 PM
Other Functions
Changing Paper Thickness
Settings
Select [Normal] or [Middle Thick/91105g/m 2 ] depending on the type of
plain paper.
Note
❒ Settings will not be cleared even
when the { Clear Modes}
} key is
pressed or the power is turned off.
❒ All paper trays are set to [Normal]
as default.
A Press the {User Tools / Counter}} key.
B Press [Maintenance].
6
C Press [Plain Paper Type].
D Select the plain paper
type for
each tray depending on the paper
to be set and press [OK].
Note
❒ When printing on paper thicker
than 91 g/m2(24 lb.), select [Middle Thick/91-105g/m2].
E Press [OK].
F Press [Exit].
157
JupiterC2_GSG_EN_Pre_FM.book Page 158 Tuesday, December 28, 2004 1:39 PM
Remarks
Counter
Displaying the Total Counter
You can display the total counter value used for all functions.
A Press the {User Tools/Counter}} key.
B Press [Counter].
6
C To print a counter list, press [Print
Counter List].
D Press the {Start}} key.
A counter list prints out.
158
JupiterC2_GSG_EN_Pre_FM.book Page 159 Tuesday, December 28, 2004 1:39 PM
7. Entering Text
Entering Text
This section describes how to enter characters. When you enter a character, it appears at the position of the cursor. If there is a character already at the cursor position, the entered character appears before it.
Available Characters
• Alphabetic characters
ABCDEFGHIJKLMNOPQRSTUVWXYZabcdefghijklmnopqrstuvwxyz
• Symbols
• Numerals
0123456789
Keys
ZHWS030E
Note
❒ When entering uppercase or lowercase letters continuously, use [Shift Lock] to
lock the case.
159
JupiterC2_GSG_EN_Pre_FM.book Page 160 Tuesday, December 28, 2004 1:39 PM
Entering Text
How to Enter Text
Entering letters
A Press [Shift] to switch between uppercase and lowercase.
B Press the letters you want to enter.
Deleting characters
A Press [Backspace] or [Delete All] to delete characters.
7
160
JupiterC2_GSG_EN_Pre_FM.book Page 161 Tuesday, December 28, 2004 1:39 PM
8. Specifications
Main Unit
❖ Configuration:
Desktop
❖ Photosensitivity type:
OPC drum
❖ Original scanning:
One-dimensional solid scanning system through CCD
❖ Copy process:
Dry electrostatic transfer system
❖ Development:
Dry two-component magnetic brush development system
❖ Fusing:
Oilless belt fusing
❖ Resolution:
600 dpi
❖ Exposure glass:
Stationary original exposure type
❖ Original reference position:
Rear left corner
❖ Warm-up time:
99 seconds or less (23 °C)
❖ Originals:
Sheet/book/objects
❖ Maximum original size:
A3L, 11" × 17"L
161
JupiterC2_GSG_EN_Pre_FM.book Page 162 Tuesday, December 28, 2004 1:39 PM
Specifications
❖ Copy paper size:
• Trays: A3L– A5L, 11" × 17"L – 51/2" × 81/2"L
• Bypass: A3L– A6L, 11" × 17"L – 51/2" × 81/2"L
• Bypass (custom size):
Vertical: 90.0 – 305.0 mm, 3.55" – 12.00"
Horizontal: 148.0 – 457.2mm, 5.83" – 18.00"
• Duplex: A3L– A5K, 11" × 17"L – 51/2" × 81/2"K (except A5L, 51/2" × 81/2" L)
• LCT: A4K, 81/2" × 11"K
❖ Paper weight:
• Paper tray: 60 – 105 g/m2, 16 – 28 lb.
• Bypass tray: 60 – 163 g/m2, 16 – 43.6 lb.
• Duplex: 60 – 105 g/m2, 16 – 28 lb.
❖ Non-reproduction area:
• Leading edge: 1.5–5.0mm, 0.06”-0.20”
• Trailing edge: 0.5–6.0mm, 0”-0.24”
• Left edge: 0.5–4.0mm, 0”-0.16”
• Right edge: 0.5–4.0 mm, 0”-0.16”
❖ First copy time:
• Types 1,2:
• Color: 10 seconds or less
• B&W: 8 seconds or less
• Type 3
• Color: 8 seconds or less
• B&W: 6 seconds or less
8
❖ Copying speed: (Type 1) Full Color / B&W
• 13/16 copies/minute (A3L, 11" × 17"L)
• 24/28 copies/minute (A4K, 81/2" × 11"K)
❖ Copying speed: (Type 2) Full Color / B&W
• 13/16 copies/minute (A3L, 11" × 17"L)
• 28/35 copies/minute (A4K, 81/2" × 11"K)
❖ Copying speed: (Type 3) Full Color / B&W
• 16/19 copies/minute (A3L, 11" × 17"L)
• 35/45 copies/minute (A4K, 81/2" × 11"K)
162
JupiterC2_GSG_EN_Pre_FM.book Page 163 Tuesday, December 28, 2004 1:39 PM
Main Unit
❖ Reproduction ratio:
Preset reproduction ratios:
Metric version
Enlargement
Inch version
400%
400%
200%
200%
141%
155%
122%
129%
115%
121%
Full size
100%
100%
Reduction
93%
93%
82%
85%
75%
78%
71%
73%
65%
65%
50%
50%
25%
25%
Zoom: From 25 to 400% in increments of 1%.
❖ Maximum continuous copy run:
999 sheets
❖ Paper capacity:
• Tray 1, 2: 500 sheets ( 80 g/m2, 20 lb.)
• Bypass tray: 100 sheets (80 g/m2, 20 lb.)
8
❖ Power consumption:
• Main unit only
Type 1
Type 2
Type 3
Warm-up
about 1.4 kw
about 1.4 kw
about 1.45 kw
Stand-by
about 0.25 kw
about 0.25 kw
about 0.25 kw
During printing
about 0.72 kw
about 0.72 kw
about 0.8 kw
Maximum
less than 1.44 kw
less than 1.44 kw
less than 1.44 kw
163
JupiterC2_GSG_EN_Pre_FM.book Page 164 Tuesday, December 28, 2004 1:39 PM
Specifications
• Complete system *1
Type 1
Type 2
Type 3
Warm-up
about 1.4 kw
about 1.4 kw
about 1.45 kw
Stand-by
about 0.25 kw
about 0.25 kw
about 0.25 kw
During printing
about 0.9 kw
about 0.9 kw
about 1.05 kw
Maximum
less than 1.44kw
less than 1.44 kw
less than 1.44 kw
*1
The complete system consists of the main unit, ADF, finisher and LCT.
❖ Dimensions (W × D × H up to exposure glass):
670 × 698 × 859 mm, 26.4" × 27.5" × 33.9"
❖ Space for main unit (W × D):
Types 1, 2, 3: 1285 × 698 mm, 50.6" × 27.5" (Bypass tray extender is used for
large size paper)
❖ Noise emission *1 :
Sound power level:
• Main unit only
Type 1
Type 2
Type 3
Stand-by
Less than 40 dB (A)
Less than 40 dB (A)
Less than 40 dB (A)
Copying
Less than 65 dB (A)
Less than 67 dB (A)
Less than 67 dB (A)
Type 1
Type 2
Type 3
Less than 40 dB (A)
Less than 40 dB (A)
Less than 40 dB (A)
Less than 71 dB (A)
Less than 71 dB (A)
Less than 73 dB (A)
Type 2
Type 3
• Complete system *3
8
Stand-by
Copying
Sound pressure level
• Main unit only
*2
Type 1
Stand-by
Less than 24 dB (A)
Less than 24 dB (A)
Less than 24 dB (A)
Copying
Less than 52 dB (A)
Less than 52 dB (A)
Less than 54 dB (A)
• Complete system *3
Type 1
Type 2
Type 3
Stand-by
Less than 24 dB (A)
Less than 24 dB (A)
Less than 24 dB (A)
Copying
Less than 59 dB (A)
Less than 59 dB (A)
Less than 61 dB (A)
*1
*2
*3
164
The above measurements, made in accordance with ISO 7779 are actual values.
Measured at the position of the bystander.
The complete system consists of the main unit, ADF, finisher and LCT.
JupiterC2_GSG_EN_Pre_FM.book Page 165 Tuesday, December 28, 2004 1:39 PM
Main Unit
❖ Weight:
Types 1, 2, 3: Approx. 120 kg, 264.6 lb.
❖ HDD:
40 GB × 2
• Capacity for Document Server
37.5 GB
• Capacity for memory sorting
14.4–17.2 GB
• Capacity for others
8 GB or more
8
165
JupiterC2_GSG_EN_Pre_FM.book Page 166 Tuesday, December 28, 2004 1:39 PM
Specifications
Options
Exposure Glass Cover
Lower this over originals for copying.
Auto Document Feeder
❖ Mode:
ADF mode, Batch mode, SADF mode, Mixed Size mode, Custom Size Originals mode Auto detect (A4, 81/2" × 11")
❖ Original size:
• A3L– B6 JIS *1 KL
Vertical : 128–297mm, 5.1"-11.7"
Horizontal : 128–432mm, 5.1"-17.0" *2
• 11" × 17"L– 51/2" × 81/2"KL
❖ Original weight:
• One-sided originals: 40–128 g/m2 (11–34 lb.)
• Two-sided originals: 52–105 g/m2 (14–28 lb.)
❖ Maximum number of originals:
80 sheets (80 g/m2, 20 lb.) or less than 11 mm, 0.43"
8
❖ Maximum power consumption:
Less than 60 W (power is supplied from the main unit)
❖ Dimensions (W×
×D×
×H):
570 × 518 × 150 mm, 22.5" × 20.4" × 6.0"
❖ Weight:
Approx. 12 kg, 26.5 lb.
*1
*2
B6 JIS-sized originals cannot be detected if they are two-sided.
While using the fax function, it can read a maximum of 1200mm.
Note
❒ Specifications are subject to change without notice.
166
JupiterC2_GSG_EN_Pre_FM.book Page 167 Tuesday, December 28, 2004 1:39 PM
Options
2 Tray Finisher
Finisher Shift Tray 1:
❖ Paper size:
A3L, B4 JISL, A4KL, B5 JISKL, A5K, 11" × 17"L, 81/2" × 14"L, 81/2" ×
11"KL
❖ Paper weight:
60 – 105 g/m2, 16 – 28 lb.
❖ Stack capacity:
• 500 sheets (A4KL, B5 JISKL, A5K, 81/2" × 11"KL) (80 g/m2, 20 lb.)
• 250 sheets (A3L, B4 JISL, 81/2" × 14"L, 11" × 17"L) (80 g/m2, 20 lb.)
Finisher Shift Tray 2:
❖ Paper size:
A3L, B4 JISL, A4KL, B5 JISKL, A5K, 11" × 17"L, 81/2" × 14"L, 81/2" × 11"KL
❖ Paper weight:
60 – 105 g/m2, 16 – 28 lb.
❖ Stack capacity:
No Staple:
• 2,000 sheets (A4K, 81/2" × 11"K) (80 g/m2, 20 lb.)
• 750 sheets (A3L, B4 JISL, A4L, B5 JISKL, 11" × 17"L, 81/2" × 14"L,
81/2" × 11"L) (80 g/m2, 20 lb.)
• 500 sheets (A5K) (80 g/m2, 20 lb.)
Staple:
• 1,500 sheets (A4K, 81/2" × 11"K) (80 g/m2, 20 lb.)
• 750 sheets (A3L, B4 JISL, A4L, B5 JISKL, 11" × 17"L, 81/2" × 14"L,
81/2" × 11"L) (80 g/m2, 20 lb.)
8
❖ Staple capacity:
• 2–50 sheets (A4KL, B5 JISKL, 81/2" × 11"KL) (80 g/m2, 20 lb.)
• 2–30 sheets (A3L, B4 JISL, 11" × 17"L, 81/2" × 14"L) (80 g/m2, 20 lb.)
❖ Staple paper size:
A3L, B4 JISL, A4KL, B5 JISKL, 11" × 17"L, 81/2" × 14"L, 81/2" × 11"KL
❖ Staple paper weight:
64 – 90 g/m2, 17 – 24 lb.
❖ Staple position:
• 1 staple – 3 positions
• 2 staples – 2 positions
167
JupiterC2_GSG_EN_Pre_FM.book Page 168 Tuesday, December 28, 2004 1:39 PM
Specifications
❖ Power consumption:
Less than 60 W (power is supplied from the main unit)
❖ Dimensions (W × D × H):
680 × 620 × 1,030 mm, 26.8" × 24.5" × 40.6" (including trays)
❖ Weight:
Approx. 55 kg, 121.3 lb.
Punch Kit (2 tray finisher)
❖ Paper size
• 2 holes: A3L– A5KL, 11" × 17"L, 81/2" × 14"L
• 3 holes: A3L, B4 JISL, A4K, B5 JISK, 11" × 17"L, 81/2" × 11"K
• 4 holes:
• Metric version: A3L, B4 JISL, A4K, B5 JISK, 11" × 17"L, 81/2" × 11"K
• Narrow 2 × 2 version: A3L– A5K, 11" × 17"L, 81/2" × 14"L
❖ Paper weight:
• 4 holes: 52 – 163 g/m2, 14 lb. – 43 lb.
• 2 or 3 holes: 52 – 163 g/m2, 14 lb. – 43 lb.
❖ Power consumption:
26.4 W (power is supplied from the main unit.)
8
❖ Dimensions (W × D × H):
142 × 456 × 92 mm, 55.9 × 179.5 × 36.2 in
❖ Weight:
Approx. 2.9 kg, 6.4 lb
Note
❒ Specifications are subject to change without notice.
Booklet Finisher
Finisher Shift Tray:
❖ Paper size:
A3L, B4 JISL, A4KL, B5 JISKL, 11" × 17"L, 81/2" × 11"KL, 81/2" × 14"L
❖ Paper weight:
60 – 128 g/m2, 16 – 34 lb.
168
JupiterC2_GSG_EN_Pre_FM.book Page 169 Tuesday, December 28, 2004 1:39 PM
Options
❖ Stack capacity:
No Staple:
• 1,000 sheets (A4K, B5 JISKL, 81/2" × 11"KL) (80 g/m2, 20 lb.)
• 500 sheets (A3L, B4 JISL, 11" × 17"L, 81/2" × 14"L) (80 g/m2, 20 lb.)
Staple:
• 1000 sheets (A4KL, B5 JISKL, 81/2" × 11"KL) (80 g/m2, 20 lb.)
• 500 sheets (A3L, B4 JISL, 11" × 17"L, 81/2" × 14"L) (80 g/m2, 20 lb.)
❖ Staple capacity:
• 50 sheets (A4K, B5 JISKL, 81/2" × 11"KL) (80 g/m2, 20 lb.)
• 25 sheets (A3L, B4 JISL, 11" × 17"L, 81/2" × 14"L) (80 g/m2, 20 lb.)
❖ Staple paper size:
A3L, B4 JISL, A4KL, B5 JISKL, 11" × 17"L, 81/2" × 14"L, 81/2" × 11"KL
❖ Staple paper weight:
64 – 80 g/m2, 17 – 21 lb.
❖ Staple position:
• 1 staple – 2 positions
• 2 staples – 1 position
❖ Saddle stitch
• Paper size:
A3L, B4 JISL, A4L, 11" × 17"L, 81/2" × 11"L, 81/2" × 14"L(80 g/m2, 20 lb.)
• Saddle stitching capacity: 10 sheets
• Stack capacity:
1–5 sheets: 20 sets
6–10 sheets: 10 sets
• Folding: Center folding
• Paper weight:
64 – 80 g/m2, 17 – 20 lb.
• Saddle Stitch – 1 position
8
❖ Power consumption:
Less than 60 W (power is supplied from the main unit)
❖ Dimensions (W × D × H):
• 1 Tray Paper Unit
695 × 603 × 834 mm, 27.4" × 23.8" × 32.9"
• 2 Tray Paper Unit
695 × 603 × 932 mm, 27.4" × 23.8" × 36.7"
❖ Weight:
Approx. 38 kg, 83.8 lb. (main unit only)
169
JupiterC2_GSG_EN_Pre_FM.book Page 170 Tuesday, December 28, 2004 1:39 PM
Specifications
Punch Kit (Booklet finisher)
❖ Paper size
• 2 holes: A3L, A4KL, B4 JISL, B5 JISKL, 11" × 17"L, 81/2" × 14"L,
81/2" × 11"KL
• 4 holes: A3L, A4K
❖ Paper weight:
64 – 128 g/m2 (16–34 lb.)
❖ Power consumption:
60 W (power is supplied from the main unit.)
❖ Dimensions (W × D × H):
137 × 560 × 170 mm, 5.4" × 22.1" × 6.7"
❖ Weight:
Approx. 3.0 kg, 6.7 lb
Note
❒ Specifications are subject to change without notice.
1 Tray Paper Unit
❖ Paper weight:
60–105 g/m2 (16–28 lb.)
8
❖ Paper size:
A3L, B4 JISL, A4KL, B5 JISKL, A5K, 11" × 17"L, 8 1/ 2" × 14"L,
8 1/ 2 " × 13"L, 8 1 / 2" × 11"KL, 8 1/ 4 " × 13"L, 8" × 13"L, 7 1/ 4 " × 10 1/ 2 "L,
81/4" × 14"L, 51/2" × 81/2" L
❖ Maximum power consumption:
Less than 50 W (power is supplied from the main unit)
❖ Paper capacity:
550 sheets (80 g/m2, 20 lb.)
❖ Dimensions (W × D × H):
578 × 648 × 876 mm, 22.8" × 25.6" × 34.5"
❖ Weight:
Approx. 18 kg, 39.7 lb.
Note
❒ Specifications are subject to change without notice.
170
JupiterC2_GSG_EN_Pre_FM.book Page 171 Tuesday, December 28, 2004 1:39 PM
Options
2 Tray Paper Unit
❖ Paper weight:
60–105 g/m2 (16–28 lb.)
❖ Paper size:
A3L, B4 JISL, A4KL, B5 JISKL, A5K, 11" × 17"L, 8 1/ 2" × 14"L,
8 1/ 2 " × 13"L, 8 1 / 2" × 11"KL, 8 1/ 4 " × 13"L, 8" × 13"L, 7 1/ 4 " × 10 1/ 2 "L,
81/4" × 14"L, 51/2" × 81/2" L
❖ Maximum power consumption:
Less than 50 W (power is supplied from the main unit)
❖ Paper capacity:
1,100 sheets (80 g/m2, 20 lb.) × 2 trays
❖ Dimensions (W × D × H):
578 × 648 × 974 mm, 22.8" × 25.6" × 38.4"
❖ Weight:
Approx. 25 kg, 55.2 lb.
Large Capacity Tray
❖ Paper size:
A4K, 81/2" × 11"K
8
❖ Paper weight:
60 – 105 g/m2, 16 – 28 lb.
❖ Paper capacity:
2,000 sheets (80 g/m2, 20 lb.)
❖ Power consumption:
Maximum 50 W (power is supplied from the main unit)
❖ Dimensions (W × D × H, option unit):
578 × 648 × 974 mm, 22.8" × 25.6" × 38.4"
❖ Weight:
Approx. 25 kg, 55.2 lb.
Note
❒ Specifications are subject to change without notice.
171
JupiterC2_GSG_EN_Pre_FM.book Page 172 Tuesday, December 28, 2004 1:39 PM
Specifications
Scanner Accessibility Unit
This unit lets you operate the machine or scan documents from the side instead
of using the control panel on the machine.
Note
❒ When the scanner accessibility unit is installed, the control panel and the
scanner unit on the machine cannot be used.
8
172
JupiterC2_GSG_EN_Pre_FM.book Page 173 Tuesday, December 28, 2004 1:39 PM
Copy Paper
Copy Paper
Recommended Paper Sizes and Types
The following limitations apply to each tray:
Tray type
Paper type and
weight
Metric version
Tray 1
60-105 g/m2
(16-28 lb.)
A4K, 81/2" × 11"K
500 sheets
Tray 2
60-105 g/m2
(16-28 lb.)
A3L, B4 JISL, A4KL, B5 JISKL, A5K, 11" × 17"L,
81/2" × 14"L, 81/2" × 11"KL, 71/4" × 101/2"L,
8" × 13"L, 81/2" × 13"L, 81/4" × 13"L
500 sheets
Paper
Tray Unit
(Tray 3–
4)(option)
Inch version
Paper capacity
8
173
JupiterC2_GSG_EN_Pre_FM.book Page 174 Tuesday, December 28, 2004 1:39 PM
Specifications
Tray type
Paper type and
weight
Metric version
Inch version
Paper capacity
Bypass
tray *1
Standard paper
60-90 g/m2 (1624 lb.)
A3L, B4 JISL, A4KL,
A6L, B5 JISKL,
A5KL, B6 JISL, 11" ×
17"L, 81/2" × 11"KL,
81/2" × 14"L, 51/2" ×
81/2"L, 12" × 18"L
B4 JISL, A4KL, B5
JISKL, A5KL, B6
JISL, A6L, PostcardL,
81/2" × 14"L, 71/4" ×
101/2"KL, 81/2" ×
13"L, 81/4" × 13"L
100 sheets
Custom size
Custom size
Vertical: 90-305 mm
Vertical: 3.6"-12.0"
Horizontal: 148-457.2 mm Horizontal: 5.8"-18.0"
Middle thick pa- A3L, B4 JISL, A4KL, B4 JISL, A4KL, B5
JISKL, A5KL, B6
per 91-105 g/m2 A6L, B5 JISKL,
A5KL, B6 JISL, 11" × JISL, A6L, PostcardL,
(24-28 lb.)
17"L, 81/2" × 11"KL, 81/2" × 14"L, 71/4" ×
81/2" × 14"L, 51/2" ×
101/2"KL, 81/2" ×
1
8 /2"L, 12" × 18"L
13"L, 81/4" × 13"L
Thick paper *3
*5
*6
106-163 g/m2
(28-43.5 lb.)
8
Custom size
Custom size
Vertical: 90-305 mm
Vertical: 3.6"-12.0"
Horizontal: 148-457.2
mm
Horizontal: 5.8"-18.0"
A3L, B4 JISL, A4KL, A3L, 11" × 17"L,
A6L, B5 JISKL,
81/2" × 11"KL,
A5KL, B6 JISL, 11" × 51/2" × 81/2"L
17"L, 81/2" × 11"KL,
81/2" × 14"L, 51/2" ×
81/2"L, 12" × 18"L
Custom size
Custom size
Vertical: 90-305 mm
Vertical: 3.6"-12.0"
*3
Horizontal: 148-457.2 mm Horizontal: 5.8"-18.0"
Translucent paper
A3L, B4 JISL, A4KL,
B5 JISKL
A3L, 11" × 17"L, 81/2" ×
11"KL, 51/2" × 81/2"L
10 sheets
OHP transparencies *7 *2
A4KL
81/2" × 11"L
50 sheets
Label paper
(adhesive labels)
B4L, A4KL
A3L, 11" × 17"L, 81/2" ×
11"KL, 51/2" × 81/2"L
30 sheets
*2 *3 *6
LCT (op60-105 g/m2
tional) *3 *4 (16-28 lb.)
*1
*2
*3
174
A4K, 81/2" × 11"K
2000
sheets
When copying onto custom size paper, you need to specify vertical and horizontal
dimensions. See “Copying from the Bypass Tray”, Copy Reference.
Placing one sheet at a time is recommended. See “Copying from the Bypass Tray”,
Copy Reference.
When loading paper, make sure the top of the stack is not higher than the limit mark
of the paper tray.
JupiterC2_GSG_EN_Pre_FM.book Page 175 Tuesday, December 28, 2004 1:39 PM
Copy Paper
*4
*5
*6
*7
The paper guide is immovable. If you want to change the size of paper placed in this
tray, contact your service representative.
If you want to use thick (128–163 g/m2, 34 lb.–43.5 lb.) paper, select [Thick Paper] on
the display panel. See “Copying from the Bypass Tray”, Copy Reference.
When copying onto label paper from the bypass tray, select [Thick Paper] on the display panel. See “Copying from the Bypass Tray”, Copy Reference.
When copying onto OHP transparencies from the bypass tray, select [OHP] on the display panel. See “Copying from the Bypass Tray”, Copy Reference.
Important
❒ If you use damp or curled paper, a misfeed may occur.
❒ Because of the type of toner used by this machine, colors may appear subdued when copied onto OHP transparencies.
Note
❒ Load paper into the paper tray, the paper tray unit and the LCT with the print
side facing down.
❒ Place paper in the bypass tray with the print side facing up.
❒ When using the bypass tray, it is recommended that you set the paper orientation to L.
❒ When loading OHP transparencies, check the front and back of the sheets,
and place them correctly, or a misfeed might occur. Set the paper orientation
to Land select A4L, 81/2"×11"K as paper size.
❒ When using OHP transparencies, fan them for each use. If you store the sheets
in the tray, they may stick together and may cause feeding problems.
❒ When copying onto OHP transparencies, remove copied sheets one by one.
❒ If multiple-sheet jams occur, load the paper sheet by sheet.
❒ Postcards should be fed using the bypass tray. Select [Thick Paper] on the display panel. See “Copying from the Bypass Tray”, Copy Reference.
❒ When copying onto letterhead paper, placing orientation differs according to
the function you are using. See p.115 “Orientation-Fixed Paper or Two-Sided
Paper”.
❒ If you load paper of the same size in the same orientation in two or more
trays, the machine automatically shifts to the other tray when the first tray in
use runs out of paper. This function is called “Auto Tray Switching”. (However, if one tray has recycled or special paper, the settings of the other trays
must be the same for Auto Tray Switching to work.) This saves interrupting
a copy run to replenish paper when making a large number of copies. See
“General Features 1/5 Auto Tray Switching”, Copy Reference and p.58 “Tray
Paper Size:Tray 2–4”.
❒ The paper types you can select in System Settings are only general classifications. Copy quality for every kind of paper in a classification is not guaranteed. See p.115 “Orientation-Fixed Paper or Two-Sided Paper” for details.
❒ If you want to use middle thick (91-105 g/m2, 24 lb.-28 lb.) paper, select [Middle Thick/91-105g/m2 ] under Plain Paper Type. See p.157 “Changing Paper
Thickness Settings”.
8
175
JupiterC2_GSG_EN_Pre_FM.book Page 176 Tuesday, December 28, 2004 1:39 PM
Specifications
Unusable Paper
R CAUTION:
• Do not use aluminum foil, carbon paper, or similar conductive paper to avoid
a fire or machine failure.
Important
❒ To prevent faults, do not use any of the following kinds of paper:
• Paper for inkjet printers
• Thermal fax paper
• Art paper
• Aluminum foil
• Carbon paper
• Conductive paper
• Paper with perforated lines
• Hemmed-edge paper
❒ Do not use paper designed for inkjet printers, as these may stick to the fusing
unit and cause a misfeed.
❒ Do not use copy paper that has been already copied onto, faults could occur
if you do.
Note
❒ To prevent misfeeds, do not use the following kinds of paper:
• Bent, folded, or creased paper
• Torn paper
• Slippery paper
• Perforated paper
• Rough paper
• Thin paper with little stiffness
• Paper with a dusty surface
❒ If you copy onto rough grain paper, the image might be blurred.
8
176
JupiterC2_GSG_EN_Pre_FM.book Page 177 Tuesday, December 28, 2004 1:39 PM
Copy Paper
Paper Storage
Note
❒ When storing paper, the following precautions should always be followed:
• Do not store paper where it will be exposed to direct sunlight.
• Avoid storing paper in humid areas (humidity: 70% or less).
• Store on a flat surface.
❒ Do not store paper vertically.
❒ Under high temperature and humid conditions, or low temperature and humid conditions, store paper in vinyl bags.
8
177
JupiterC2_GSG_EN_Pre_FM.book Page 178 Tuesday, December 28, 2004 1:39 PM
INDEX
C
1 Tray paper unit, 21
2 Tray Finisher, 167
2 Tray finisher, 21
2 Tray paper unit, 21
A
Adding a Group to Another Group, 99
Adding staples, 131
Adding toner, 116
Address Book
Change Order, 66
Edit Title, 67
Program/Change/Delete Group, 65
Select Title, 68
Address book, 70
Address Book Management, 65
ADF, 21
Adjusting the Color Registration, 138
Auto Color Registration, 138
Fuser Adjustment for thick paper, 138
Adjust/Program Color key, 23
Administrator Authentication Management, 63
Administrator Tools, 63
AOF (Always On), 68
Authentication Information, 75
Auto color calibration, 142
Auto Delete File, 68
Auto Document Feeder, 19, 166
cleaning, 150
Auto Erase Memory Setting, 69
Auto Off, 30
Auto off timer, 61
Auto reset timer
copier/Document Server, 62
facsimile, 62
scanner, 62
system, 61
B
Booklet finisher, 21, 168
Browse network, 90
178
Changing a group name, 98
Changing a name Registered Name, 73
Changing a registered e-mail destination, 87
Changing a registered fax destination, 82
Changing a registered folder, 91, 94
Changing a Registered IP-Fax Destination, 85
Changing a registered
Transfer Station/Receiving Station, 105
Changing a user code, 76
Changing paper size of the paper tray, 128
Changing Paper Thickness Settings, 157
Changing the language, 156
Changing the paper size, 128
Check Modes key, 23
Cleaning the Dustproof Glass, 151
Clearing misfeeds, 119
Clearing the number of prints, 78
Clear Modes key, 24
Clear/Stop key, 24
Color circle, 23
Color selection keys, 24
Combined function operations, 31
Common key operations, 25
Control panel, 20, 23
Copy Count Display, 55
Copy paper, 173
Cover sheet tray, 60
D
Delete All Files, 68
Deleting a group, 99
Deleting a registered e-mail destination, 88
Deleting a registered fax destination, 83
Deleting a registered folder, 92, 95
Deleting a registered
Transfer Station/Receiving Station, 106
Deleting a user, 74
Deleting a user code, 76
Display/Clear/Print Counter per User, 64
Displaying names registered in groups, 97
Displaying the Counter for each user code, 77
Displaying the Total Counter, 158
Display panel, 23, 25
Display/Print Counter, 64
JupiterC2_GSG_EN_Pre_FM.book Page 179 Tuesday, December 28, 2004 1:39 PM
Document Server, 37
Deleting, 47
Downloading, 48
Printing, 44
Selecting, 42
Using the Document Server, 39
Viewing, 47
Do's and Don'ts, 145
Duplex reversal unit, 19
E
Earth leakage breaker, 19, 152
E-mail destination, 86
Energy Saver key, 24
Entering text, 159
Environment, 148
Erase All Memory, 69
Exposure glass, 19
cleaning, 150
Exposure glass cover, 21
cleaning, 150
Extended Security, 63
External options, 21
External tray, 19
F
Fax destination, 79
Finisher, 21
Firmware Version, 68
Front cover, 20
FTP, 93
Function keys, 24
Function Priority, 55
Function reset timer, 56
Function status indicators, 24
Fuser Adjustment Sheet II, 141
I
Indicators, 23
Inquiry, 156
Internal options, 22
Interrupt key, 24
K
# key, 24
Key Counter Management, 63
L
Large Capacity Tray, 171
Large Capacity Tray (LCT), 21
LDAP Authentication, 108
Left tray, 21
Loading Paper
Large Capacity Tray, 114
Loading paper, 113
paper size, 128
paper tray, 113
M
Machine environment, 148
Main power indicator, 24
Main power switch, 19, 28
Maintaining Your Machine, 150
Main Unit, 161
Misfeeds, 119
Moving, 148
Multi-Access, 33
N
Number keys, 24
O
Operation switch, 24, 28
Options, 166
P
Panel off timer, 61
Panel Tone, 55
Paper
changing, 128
loading, 113
Paper tray, 20
Paper tray priority
copier, 58
facsimile, 58
printer, 58
Paper type
bypass tray, 59
tray 1–4, 59
Power connection, 149
Power indicator, 24
Print Address Book
Destination List, 67
Printing the Counter for each user code, 77
Print Priority, 55
Program/ Change Administrator, 63
Program / Change / Delete LDAP Server, 68
Program key, 24
Protection
code, 101, 102
destination, 101
Punch kit (2 tray finisher), 168
Punch kit (Booklet finisher), 170
179
JupiterC2_GSG_EN_Pre_FM.book Page 180 Tuesday, December 28, 2004 1:39 PM
R
Receiving Station, 103
Registering a fax destination, 80
Registering a name, 73
Registering an e-mail destination, 86
Registering a New Group, 96
Registering a new user code, 75
Registering an IP-Fax Destination, 84
Registering a protection code, 101
Registering a protection code
to a group user, 102
Registering a protection code
to a single user, 101
Registering a
Transfer Station/Receiving Station, 103
Registering Folders, 89
Registering Names, 73
Registering names to a group, 96, 97
Registering SMTP and LDAP
Authentication, 107
Registering the Transfer Request, 103
Remarks, 145
Removing a name from a group, 98
Removing jammed staples, 133
Removing punch waste, 135
Replacing the Waste Toner Bottle, 154
S
Safety information, 12
Sample Copy key, 24
Saving Color Copies, 146
Saving energy, 30
Scanner Accessibility Unit, 172
Screen contrast knob, 23
Set date, 62
Set time, 62
Slip sheet tray, 60
SMB, 89
SMTP Authentication, 107
Specification
2 Tray Paper Unit, 171
Specifications, 161
1 tray paper unit, 170
2 Tray Finisher, 167
Auto Document Feeder, 166
booklet finisher, 168
Large Capacity Tray (LCT), 171
main unit, 161
punch kit, 168, 170
Scanner Accessibility Unit, 172
180
Standard Tray, 20
Staples
adding, 131
removing jammed staples, 133
Start key, 24
System Reset, 32
T
Toner, 147
adding, 116
storage, 147
To register an FTP folder, 93
To register an SMB folder, 89
Transfer Station, 103
Tray paper size, 58
U
Upper right cover, 20
Use LDAP Server, 68
User Authentication Management, 63
User Tools/Counter key, 23
User Tools (System Settings), 51
Using FTP to Connect, 93
Using SMB to Connect, 89
V
Ventilation holes, 19
W
Warm Up Notice (copier/Document Server), 55
Web browser, 47
JupiterC2_GSG_EN_Pre_FM.book Page 181 Tuesday, December 28, 2004 1:39 PM
MEMO
181
JupiterC2_GSG_EN_Pre_FM.book Page 182 Tuesday, December 28, 2004 1:39 PM
MEMO
182
EN
USA
B180-7505
Paper type: OK Prince Eco G100(55kg), Paper Thickness=80 µm // Pages in book=192 // Print scale=81%
Gap (when printed at 81% scale) = Pages in book × Paper thickness / 2 = 7.680000 mm
Introduction
This manual contains detailed instructions and notes on the operation and use of this machine. For your
safety and benefit, read this manual carefully before using the machine. Keep this manual in a handy
place for quick reference.
In accordance with IEC 60417, this machine uses the following symbols for the main power switch:
a means POWER ON.
b means POWER OFF.
c means STAND BY.
Important
Contents of this manual are subject to change without prior notice. In no event will the company be liable for direct, indirect, special, incidental, or consequential damages as a result of handling or operating the machine.
Notes:
Some illustrations in this manual might be slightly different from the machine.
Certain options might not be available in some countries. For details, please contact your local dealer.
Laser Safety:
CDRH Regulations
This equipment complies with requirements of 21 CFR Subchapter J for class 1 laser products. This
equipment contains five AlGalnP laser diodes, 7–milliwatt, 645–660 nanometer wavelength for each
emitter. This equipment does not emit hazardous light, since the beam is totally enclosed during all customer modes of operation and maintenance.
Caution:
Use of controls or adjustments or performance of procedures other than those specified in this manual
might result in hazardous radiation exposure.
Notes:
The model names of the machines do not appear in the following pages. Check the type of your machine before reading this manual. (For details, see P.17 “Machine Types”.)
•
Type 1: C2824/DSc428/LD328c/Aficio 3228C
•
Type 2: C3528/DSc435/LD335c/Aficio 3235C
•
Type 3: C4535/DSc445/LD345c/Aficio 3245C
Certain types might not be available in some countries. For details, please contact your local dealer.
Two kinds of size notation are employed in this manual. With this machine refer to the inch version.
For good copy quality, the supplier recommends that you use genuine toner from the supplier.
The supplier shall not be responsible for any damage or expense that might result from the use of parts
other than genuine parts from the supplier with your office products.
Power Source
120V, 60Hz, 12A or more
Please be sure to connect the power cord to a power source as shown above. For details about power
source, see P.149 “Power Connection”.
Copyright © 2004
Paper type: OK Prince Eco G100(55kg), Paper Thickness=80 µm // Pages in book=192 // Print scale=81%
Gap (when printed at 81% scale) = Pages in book × Paper thickness / 2 = 7.680000 mm
Operating Instructions
General Settings Guide
Getting Started
Combined Function Operations
Document Server
User Tools (System Settings)
Troubleshooting
Remarks
Entering Text
Specifications
Type for C2824/DSc428/LD328c/Aficio 3228C
Type for C3528/DSc435/LD335c/Aficio 3235C
Type for C4535/DSc445/LD345c/Aficio 3245C
Printed in Japan
EN USA B180-7505
B1807505
Read this manual carefully before you use this machine and keep it handy for future reference. For safe and correct use, be sure to read the Safety
Information in this manual before using the machine.
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement