02_RSX_CassetteAtt
Accessory
INSTALLATION
INSTRUCTIONS
PARTS LIST
Cassette player
Application
Publications No.
BII 22639
CASSETTE PLAYER
P/N 08A03-5C2-050
2002 RSX
Issue Date
JUNE 2001
TOOLS AND SUPPLIES REQUIRED
Phillips screwdriver
Stubby Phillips screwdriver
Ratchet
8 mm and 10 mm Sockets
Shop towel
Diagonal cutters
INSTALLATION
Owner’s Manual
Customer Information: The information in this
installation instruction is intended for use only by
skilled technicians who have the proper tools,
equipment, and training to correctly and safely add
equipment to your vehicle. These procedures
should not be attempted by “do-it-yourselfers.”
1.
If equipped, make sure you have the anti-theft
code for the radio, then write down the
frequencies for the preset buttons.
2.
Disconnect the negative cable from the battery.
3.
Pry up on the seven clips, and remove the center
lower cover. Unplug the accessory socket
connector. Take care not to damage the clips.
5 Washer-screws, 5 x 8 mm
Wire tie
CLIP (7)
Harness clip
ACCESSORY
SOCKET
ACCESSORY
SOCKET
CONNECTOR
© 2001 American Honda Motor Co., Inc - All Rights Reserved.
BII 22639
(0106)
E2334E
CENTER LOWER COVER
08B03-S6M-2001-91
1 of 4
4.
Using a stubby Phillips screwdriver, remove the
two bolts that fasten the center panel.
7.
Remove the radio from the center panel bracket
(four bolts).
ANTENNA LEAD
BOLTS
CLIP (4)
SELFTAPPING
SCREWS
VEHICLE CONNECTORS
RADIO
BOLTS
POCKET
BOLTS
CENTER PANEL BRACKET
CENTER PANEL
SELF-TAPPING
SCREWS
8.
CLIP (4)
5.
Pull the center panel toward you to release the
eight clips, unplug the connectors and the
antenna lead, and remove the center panel.
Take care not to damage the clips.
6.
Remove the hazard switch from the center panel
(two self-tapping screws).
Remove the pocket from the center panel bracket
(four self-tapping screws). Save the pocket and
the self-tapping screws for your customer in case
the cassette player needs to be removed.
HAZARD SWITCH
CENTER PANEL
2 of 4
SELFTAPPING
SCREWS
BII 22639 (0106)
© 2001 American Honda Motor Co., Inc - All Rights Reserved.
9.
Stack the radio on top of the cassette player, and
slide them into the center panel bracket. Install
the radio with the four bolts removed in step 7,
and install the cassette player with four 5 x 8 mm
washer-screws supplied.
12. Reinstall the hazard switch using the two selftapping screws you removed in step 6.
HAZARD SWITCH
RADIO
BOLTS
(Removed in step 7.)
BOLTS
(Removed in step 7.)
CASSETTE
PLAYER
5 x 8 mm
WASHERSCREWS
(supplied)
5 x 8 mm
WASHER-SCREWS
(supplied)
CENTER PANEL
BRACKET
CENTER PANEL
SELFTAPPING
SCREWS
(Removed
in step 6.)
Use the center holes.
10. Slightly bend the harness clip, and attach it to the
rear of the cassette player with one 5 x 8 mm
washer-screw supplied.
RADIO
CONNECTOR
HARNESS
CLIP
CASSETTE PLAYER
5 x 8 mm
WASHER-SCREW
(supplied)
CASSETTE PLAYER
BUS CABLE
11. Loop the BUS cable, and attach it to the harness
clip. Plug the connector of the BUS cable into the
rear of the radio.
© 2001 American Honda Motor Co., Inc - All Rights Reserved.
BII 22639 (0106)
3 of 4
13. Plug the antenna lead and the vehicle harness
connectors into the rear of the radio and the
hazard switch. Slide the center panel into the
radio opening, and secure it with the two bolts.
Using a 10 mm wrench, tighten the bolts
securely.
•
14. Reconnect the negative cable to the battery.
15. Check the operation of the cassette player
according to the Owner’s Manual supplied.
16. Enter the radio anti-theft code, and reset the
customer’s radio station presets.
17. Reset the clock.
Without CD Changer:
VEHICLE HARNESS
CONNECTORS
ANTENNA LEAD
18. Put the cassette player Owner’s Manual and the
pocket and screws (removed in step 8) into the
glove box.
NOTE: Whenever the battery is disconnected, the
driver’s window AUTO function is disabled.
19. Start the engine. Push down on the driver’s
window switch until the window is fully open.
20. Pull up on the driver’s window switch to close the
window completely, then hold the switch for a
second or two more.
21. Test the AUTO window function.
CENTER PANEL
BOLTS
•
With CD Changer: Plug the connector of the CD
changer BUS cable into the cassette player.
ANTENNA
LEAD
RADIO
VEHICLE
20-PIN
CONNECTOR
CONNECTOR
CASSETTE PLAYER
CD CHANGER
BUS CABLE
(When the CD
Changer is installed)
4 of 4
BII 22639 (0106)
© 2001 American Honda Motor Co., Inc - All Rights Reserved.
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement