Jordan MK80 specs

Jordan MK80 specs
Temperature Regulators
Mark 80 Series
Self-Operated Temperature Regulators
The MK80 Series is completely self-operated and requires no external power source or other expensive
instrumentation to operate the valve.
The operation of the MK80 is fairly simple. A pre-measured amount of liquid fill is drawn into the thermal system filling the upper diaphragm chamber, the capillary
tube, and most of the bulb. As the controlled temperature increases, the volatile liquid fill in the sensing bulb
begins to vaporize and creates pressure on the sealed
system. This pressure drives the valve stem, closing
direct acting valves, or opening reverse acting valves.
Accurate temperature control begins with a reliable
actuator.
•
Simple replacement: attached to the yoke by
just four screws, the actuator can be replaced
in less than five minutes. Control ranges can be
changed with the valve in line by simply replacing the actuator.
•
Liquid/vapor thermal system: to obtain the force
needed to position the valve seats, Jordan uses
a liquid/vapor thermal system that is capable
of delivering far more operating power than the
simple liquid expansion systems used on other
temperature regulators. As the sensed temperature increases, the liquid fill in the bulb begins to
vaporize and creates pressure within the sealed
system. This pressure, exerted on the diaphragm,
drives the valve stem to modulate the valve seats
to the proper position.
A temperature regulator is only as good as its actuator
and a great deal of research has gone into the development of Jordan’s stainless steel SWA actuator. That
is why the SWA, combined with Jordan’s sliding gate
regulator design, provides the finest temperature control available in a self-operated design. Among the features of the SWA actuator:
•
Heliarc welded construction: the upper and lower casings, and diaphragm, are heliarc welded
around the circumference to fuse a solid bond
and eliminate the need for a gasket, a common
source for leakage.
•
Stainless Steel diaphragm: pre-formed from AISI
347 SST to eliminate rupturing caused by metal
fatigue brought about by constant stress, the
most common failure in bellows actuators.
•
Sensitive control: because of the stroke length,
the span of an SWA is about 1/3 that of a typical
bellows actuator.
Features
•
•
•
High rangeability — controls flows from 5% to
100% of rated capacity.
Sliding gate seats provide —
—— Straight-through flow for reduced turbulence and quiet operation
—— Short stroke for fast response and accurate
temperature control
—— Easily interchangeable Cv’s
—— Tight shutoff due to overlap of seat closure
area
Available with capillaries up to 100 feet in length.
Jordan Valve, a division of Richards Industries
3170 Wasson Road • Cincinnati, OH 45209
513.533.5600 • 800.543.7311 • 513.871.0105 (f)
[email protected] • www.jordanvalve.com
Mark 80 Self-Operated Temperature Regulators
Because of the shorter stroke length of the sliding gate
seats, the MK80 is able to utilize a sealed actuator
with a stainless steel diaphragm, and does not require
a bellows to operate. To seal the actuator, the upper
and lower casings and diaphragm are heli-arc welded
around the circumference to create a solid bond. This
seal eliminates the need for any type of gasket. All
sealing surfaces on the MK80 are metal to metal.
Mark 80 Self-Operated Temperature Regulators
Specifications
Line Sizes: 1/2" (DN15) through 2" (DN50)
Cv Values & Maximum Differential Pressure
Size
End Connections:
•
Threaded — FNPT, BSPT, BSPP
•
ANSI Flanges — 150#, 300#
•
DIN Flanges — PN10/16, PN25/40
Inches
Body Materials:
•
Ductile Iron
•
Bronze
•
Carbon Steel
•
Stainless Steel
Flow Coefficient
DN
Cv
Kv
1/2" or
3/4"
15 or 20
2.5 or
4.4
2,15 or
3,78
1" or
1-1/4"
25 or 32
6.4 or
9.5
5,50 or
8,17
1-1/2"
40
15
12,9
2"
50
25 or 30
21,5 or
25,8
Max ∆P
Seat
Material
PSI
SST
125
8,62
Jorcote
300
20,68
SST
125
8,62
Jorcote
250
17,24
BAR
SST
75
5,17
Jorcote
175
12,07
SST
75
5,17
Jorcote
175
12,07
Low Flow Cv's Available
Reduced Cv's can be used in a valve of any size so long
as the required Cv is a smaller value than the standard for
that particular size. In addition, the following Cv values
can be provided:
Trim Materials:
•
303 SS for DI, BRZ & CS body valves
•
316SS for SS body valves
Seat Materials:
•
Jorcote on SST — Standard
•
Jorcote/Jordanic on SST — For severe service
•
Chrome Plated SST — Optional
1.6
(1,4)
0.84
(0,72)
0.42
(0,36)
0.21
(0,18)
0.02
(0,017)
0.008
(0,007)
0.004
(0,003)
0.002
(0,0017)
0.08
(0,07)
0.04
(0,03)
0.0008 (0,0007)
(N/A in 316SS)
Yoke Material: Carbon Steel
Available Temperature Control Ranges & Spans
Stem Packing Materials:
•
Spring-loaded Teflon (to 450°F max/232°C max)
•
Braided (above 500°F/260°C up to 650°F/343°C)
Service: steam, water, oil, gas, air and chemicals
Shutoff: ANSI Class IV
Action:
•
Direct (increase in temperature closes valve)
•
Reverse (increase in temperature opens valve)
Body Rating (Max):
•
Ductile Iron: 988 psi @ 100°F; 988 psi @ 450°F (68,1
bar @ 37,8°C; 68,8 bar @232,2°C)
•
Carbon Steel: 1480 psi @ 100°F; 1235 psi @ 450°F
(102,0 bar @ 37,8°C; 85,2 bar @ 232,2°C)
•
Stainless Steel: 1480 psi @ 100°F; 990 psi @ 450°F
(102,0 bar @ 37,8°C; 68,3 bar @ 232,2°C)
•
Bronze: 500 psi @ 100°F; 350 psi @ 450°F (34,5 bar
@ 37,8°C; 24,1 bar @ 232,2°C)
•
-20°F (-28,9°C) temperature limit on all materials
•
For other temperatures, consult factory
Overheat Protection: 100°F (38°C) above top of control
range
Range ˚F
(˚C)
Thermal Fill
-20 to 20 **
(-29 to -7)
Temperature span from closed to open
˚F (˚C) with standard spring*
1/4" - 3/4"
1" - 1-1/4"
1-1/2" - 2"
Freon 22
8 (4)
12 (7)
16 (9)
10 to 55
(-12 to 13)
Freon R134A
9 (5)
14 (8)
17 (9)
35 to 90
(2 to 32)
Iso Butane
11 (6)
15 (8)
18 (10)
55 to 115
(13 to 46)
N-Butane
11 (6)
15 (8)
18 (10)
80 to 140
(27 to 60)
Ethyl
Chloride
11 (6)
15 (8)
18 (10)
110 to 165
(43 to 74)
Freon R123
15 (8)
22 (12)
26 (14)
120 to 185
(49 to 85)
Ethyl Ether
15 (8)
22 (12)
26 (14)
160 to 225
(71 to 107)
Acetone
15 (8)
22 (12)
26 (14)
205 to 260
(96 to 127)
Isopropyl
Alcohol
9 (5)
14 (8)
17 (9)
230 to 290
(110 to 143)
N-Propyl
Alcohol
11 (6)
15 (8)
18 (10)
265 to 325
(129 to 163)
N-Butyl
Alcohol
11 (6)
15 (8)
18 (10)
315 to 400†
(157 to 204)
M-Xylene
12 (7)
19 (11)
21 (12)
380 to 450†
(193 to 232)
P-Cymene
12 (7)
19 (11)
21 (12)
* Lower spans and ranges available with optional light spring.
** Requires reinforced actuator
† Requires 1" x 14" bulb.
-2-
Mark 80 Self-Operated Temperature Regulators
Thermal System Specifications
Actuator: Type SWA
Types of Bulbs
Capillary Material:
•
Standard — Copper
•
Optional — SST
•
Type C: Finned Bulb
•
Type D: Bulb with Rigid "Dead" Extension
•
Type E: Bulb with Pressure-tight Extension (well
required for support when mounted horizontally)
•
Type F: Bulb Extension with Adjustable Union
3 x 2 for
copper
3" dia. for
SST
Armor/Bulb Material:
•
Standard — SST with copper bulb
•
Optional — SST with SST bulb; Teflon with Teflon/
SST bulb
Capillary/Armor Length:
•
Standard — 8 feet
•
Optional — lengths to 100 feet
Standard Bulb Dimensions
Nominal Bulb Size (Diameter x Length)
for ranges beginning:
Bulb Type
101°F (38,3°C) or above
100°F (37,7°C) or below
1" x 12" (standard)
(2,5cm x 30,5cm)
1" x 14" (standard)
(2,5cm x 35,6cm)
3/4" x 23" (optional)
(1,9cm x 58,4cm)
3/4" x 27" (optional)
(1,9cm x 68,6cm)
1" x 12" (SST only)
(2,5cm x 30,5cm)
1" x 14" (SST only)
(2,5cm x 35,6cm)
1-1/8" x 14" (CU only)
(2,9cm x 35,6cm)
1-1/8" x 14" (CU only)
(2,9cm x 35,6cm)
1" x 12"
(2,5cm x 30,5cm)
1" x 14"
(2,5cm x 35,6cm)
A&B
C
D, E, & F
Types of Bulbs
•
Type A: Standard Bulb
•
Type B: Plain Bulb
Types of Thermal Wells
1" NPT
external
thread
on tank
fitting
Type A: standard threaded connection
•
*
D plus 1/8"
* Internal thread is 1-1/4" 18 UNEF 28
Inverted
Mounting (must
be specified on
order)
Type B: optional flanged connection
•
*
D plus 1/8"
Flange: 1-1/2" x 150#,
2" x 150#, 1-1/2" x
300#, 2" x 300#
-3-
* Internal thread is 1-1/4" 18 UNEF 28
Mark 80 Self-Operated Temperature Regulators
Dimensions
5" (114mm) Min
D
Flanged Ends
•
Size
1/2"
B
3/4"
1"
1-1/4"
C
1-1/2"
A
A1
•
Threaded Ends
•
Dimensions (inches)
Size
Material
A
B
C
D
Weight
(lbs.)
1/2" &
3/4"
DI/BRZ
3.62
12.00
2.18
7.00
20
CS/SS
3.65
12.00
2.18
7.00
21
DI/BRZ
4.12
12.25
2.62
7.00
22
CS/SS
4.12
12.25
2.62
7.00
23
DI/BRZ
4.12
12.25
2.62
7.00
22
DI/BRZ
4.50
12.75
2.75
7.00
24
1"
1-1/4"
1-1/2"
2"
•
2"
CS/SS
4.65
12.75
2.75
7.00
25
DI/BRZ
4.50
12.81
3.00
7.00
24
CS/SS
5.50
12.81
3.00
7.00
27
Size
(DN)
15 &
20
25
32
40
50
Material
15
20
25
32
40
DI/BRZ
50
Dimensions (mm)
A
B
C
D
Weight
(kg)
92
305
55
178
9,1
CS/SS
93
305
55
178
9,5
DI/BRZ
105
311
67
178
10,0
CS/SS
105
311
67
178
10,4
DI/BRZ
105
311
67
178
10,0
DI/BRZ
114
324
70
178
10,9
CS/SS
118
324
70
178
11,3
DI/BRZ
114
325
76
178
10,9
CS/SS
140
325
76
178
12,2
-4-
Dimensions (inches)
A1
B
C
Weight (lbs.)
D
DI/BRZ
CS/SS
150#
7.25
12.00
2.81
7.00
21
23
300#
7.50
12.00
2.81
7.00
22
24
150#
7.25
12.00
2.81
7.00
22
25
300#
7.62
12.00
2.81
7.00
23
28
150#
7.25
12.25
2.62
7.00
24
28
300#
7.75
12.25
2.62
7.00
25
30
150#
7.87
12.25
2.62
7.00
25
—
300#
8.37
12.25
2.62
7.00
26
—
150#
8.75
12.75
2.75
7.00
27
32
300#
9.25
12.75
2.75
7.00
30
38
150#
10.00
12.81
3.00
7.00
29
38
300#
10.50
12.81
3.00
7.00
31
42
Flanged Ends, Metric
Size
(DN)
Threaded Ends, Metric
ANSI
Flange
Dimensions (mm)
Weight (kg)
Flange
(PN)
A1
B
C
D
DI/BRZ
10/16
130
305
55
178
9,5
10,4
25/40
130
305
55
178
10
10,9
CS/SS
10/16
150
305
55
178
10
11,3
25/40
150
305
55
178
10,4
12,7
10/16
160
311
67
178
10,9
12,7
25/40
160
311
67
178
11,3
13,6
10/16
180
311
67
178
11,3
—
25/40
180
311
67
178
11,8
—
10/16
200
324
70
178
12,2
14,5
25/40
200
324
70
178
13,6
17,2
10/16
230
325
76
178
13,2
17,2
25/40
230
325
76
178
14,1
19,1
Mark 80 Self-Operated Temperature Regulators
Ordering Schematic
1
—
2
3
—
1
/
4
5
Model
6
7
8
9
5
10
Trim
80
Standard
T3
303SS / Teflon Packing
80T
with Thermometer
T6
316SS / Teflon Packing
TM
Monel / Teflon Packing
2
Size (DN)
11
TA
Alloy 20 / Teflon Packing
Hastelloy C / Teflon Packing
025
1/4" (DN8)
TH
038
3/8" (DN12)
I3
303SS / 287-I Packing
050
1/2" (DN15)
I6
316SS / 287-I Packing
075
3/4" (DN20)
IM
Monel / 287-I Packing
100
1" (DN25)
IH
Hastelloy C / 287-I Packing
125
1-1/4" (DN32)
ZZ
Non-Standard
150
1-1/2" (DN40)
200
2" (DN50)
3
Seats
6
Body Material
Material
A
Cv
303SST
Y
0.0008
DI
Ductile Iron
B
316SST
E
0.0002
BR
Bronze
Q
303 / Teflon
F
0.004
CS
Carbon Steel
R
316 / Teflon
G
0.008
S6
Stainless Steel
S
Monel / Teflon
H
0.02
4
End Connections
PT
T
Alloy 20 / Teflon
I
0.04
U
Hastelloy C / Teflon
J
0.08
303SS / Jorcote
1
0.21
NPT
I7
PN10 DIN IFE
V
BT
BSPT
F7
PN10 FE (except IFE)
W
316SS / Jorcote
2
0.42
BP
BSPP
I6
PN16 DIN IFE
X
303SS / Jorcote / Jordanic
3
0.84
SW
FSW
F6
PN16 FE (except IFE)
Y
316SS / Jorcote / Jordanic
4
1.6
F1
125# FE
I8
PN25 DIN IFE
1
303SST w/std. W.H.
5
2.5
2
316SST w/std. W.H.
I5
150# IFE
F8
PN25 FE (except IFE)
6
4.4
F5
150# FE (except IFE)
I4
PN40 DIN IFE
7
6.4
F2
250# FE
F4
PN40 FE (except IFE)
8
9.5
I3
300# IFE
ZZ
Non-Standard
F3
300# FE (except IFE)
ZZ
9
15
A
25
B
30
Non-Standard
Continued on page 6.
-5-
Mark 80 Self-Operated Temperature Regulators
Ordering Schematic (Cont'd)
7
Standard Spring °F
Standard Spring °C
06
-20 to 20*
A6
-29 to -7
12
10 to 55
B2
-12 to 13
9
19
35 to 90
B9
2 to 32
N1N1Q
1" x 12"
27
55 to 115
C7
13 to 46
N2N1Q
1" x 14"
8 (2,4)
1" x 12"
10 (3,1)
35
80 to 140
D5
27 to 60
42
110 to 165
E2
43 to 74
A2A2A
1" x 14"
49
120 to 185
E9
49 to 85
A1A4A
1" x 12"
15 (4,6)
58
160 to 225
F8
71 to 107
A2A4A
1" x 14"
15 (4,6)
66
205 to 260
G6
96 to 127
72
230 to 290
H2
110 to 143
81
265 to 325
J1
129 to 163
A2A4R
88
315 to 400
J8
157 to 204
A2A5R
93
380 to 450
K3
193 to 232
Q1N1Q
1" x 12"
Q2N1Q
1" x 14"
8 (2,4)
G1B2A
1" x 12"
10 (3,1)
G2B2A
1" x 14"
G1B3A
1" x 12"
G2B3A
1" x 14"
-25 to -5*
A5
-32 to -21
11
5 to 35
B1
-15 to 2
17
30 to 70
B7
-1 to 21
10 (3,1)
1" x 14"
10 (3,1)
Copper
Type A
12 (3,7)
15 (4,6)
8 (2,4)
10 (3,1)
12 (3,7)
SST
Type A
12 (3,7)
24
50 to 90
C4
10 to 32
G1B4A
1" x 12"
15 (4,6)
75 to 115
D2
24 to 46
G2B4A
1" x 14"
15 (4,6)
41
105 to 140
E1
41 to 60
G1B5A
1" x 12"
20 (6,1)
G2B5A
1" x 14"
20 (6,1)
46
115 to 160
E6
46 to 71
56
155 to 200
F6
68 to 93
64
195 to 235
G4
91 to 113
71
225 to 270
H1
107 to 132
79
260 to 300
H9
127 to 149
86
310 to 370
J6
154 to 188
H1B1A
1" x 12"
92
375 to 440
K2
191 to 227
H2B1A
1" x 14"
8 (2,4)
H1B2A
1" x 12"
10 (3,1)
H2B2A
1" x 14"
H1B3A
1" x 12"
H2B3A
1" x 14"
H1B4A
1" x 12"
15 (4,6)
H2B4A
1" x 14"
15 (4,6)
H1B5A
1" x 12"
20 (6,1)
H2B5A
1" x 14"
20 (6,1)
A
Size for Bulb Diameter x Length
B
Type A,
1" NPT, Cu
A
Type A,
1" NPT, SST
B
8 (2,4)
G2B2R
10 (3,1)
1" x 12"
(24,5mm x 304,8mm)
1" x 14"
(24,5mm x 355,6mm)
E
Type B,
1-1/2" x 150#, SST
H2B1R
F
Type B,
1-1/2" x 300#, SST
H2B3R
Type B,
2" x 150#, SST
H2B5R
Type B,
2" x 300#, SST
J3T4A
G
H
1" x 14"
SST
Type A
12 (3,7)
15 (4,6)
G2B5R
Thermowell
Type, Fitting & Material
G2B1R
G2B4R
* Requires reinforced actuators
10 (3,1)
12 (3,7)
SST
Type B
12 (3,7)
8 (2,4)
1" x 14"
H2B4R
SST
Type B
12 (3,7)
15 (4,6)
SWA
Reinforced
SWA
20 (6,1)
J3T1A
1" x 17"
8 (2,4)
TFE
Coated
Type B
10 (3,1)
12 (3,7)
Tank Fitting Only
11
1" NPT Brass for 1" Bulb
12
1" NPT SST for 1" Bulb
D
Direct
NN
None
R
Reverse
-6-
Reinforced
SWA
8 (2,4)
10 (3,1)
10
SWA
20 (6,1)
H2B2R
J3T5A
Reinforced
SWA
20 (6,1)
32
G2B3R
SWA
8 (2,4)
A2A2R
Light Spring °C
05
Copper
Type A
A2A1R
A2A3R
Actuator
8 (2,4)
A1A2A
Light Spring °F
8
Thermowell System
Bulb: Refer to
the standard bulb Cap/Arm
dimensions chart
ft (m)
for metrics
Range
Action
SWA
Mark 801/802 Series
Self-Operated Temperature Regulators
The MK801/802 Series is completely self-operated and
requires no external power source or other expensive instrumentation to operate the valve.
The Mark 801/802 Series is the high-flow and super-high
flow versions of our Mark 80 Series temperature regulator.
Accurate temperature control begins with a reliable
actuator.
A temperature regulator is only as good as its actuator
and a great deal of research has gone into the development of Jordan’s stainless steel SWA actuator. That is why
the SWA, combined with Jordan’s sliding gate regulator
design, provides the finest temperature control available
in a self-operated design. Among the features of the SWA
actuator:
•
Heliarc welded construction: the upper and lower
casings, and diaphragm, are heliarc welded around
the circumference to fuse a solid bond and eliminate the need for a gasket, a common source for
leakage.
•
Stainless Steel diaphragm: pre-formed from AISI 347
SST to eliminate rupturing caused by metal fatigue
brought about by constant stress, the most common
failure in bellows actuators.
•
Sensitive control: because of the stroke length, the
span of an SWA is about 1/3 that of a typical bellows
actuator.
•
•
Simple replacement: attached to the yoke by just
four screws, the actuator can be replaced in less
than five minutes (without the need to adjust the
stroke after replacement). Control ranges can be
changed with the valve in line by simply replacing
the actuator.
Features
•
Liquid/vapor thermal system: to obtain the force
needed to position the valve seats, Jordan uses a
liquid/vapor thermal system that is capable of delivering far more operating power than the simple liquid expansion systems used on other temperature
regulators. As the sensed temperature increases,
the liquid fill in the bulb begins to vaporize and cre- •
ates pressure within the sealed system. This pressure, exerted on the diaphragm, drives the valve
stem to modulate the valve seats to the proper position.
-7-
Sliding gate seats provide —
——
Straight-through flow for reduced turbulence
and quiet operation
——
Short stroke for fast response and accurate
temperature control
——
Easily interchangeable Cv’s
——
Tight shutoff due to overlap of seat closure
area
Available with capillaries up to 100 feet (30m) in
length.
Mark 801/802 Self-Operated Temperature Regulators
Specifications
Cv Values & Maximum Differential Pressure
• Mark 801
Line Sizes: 1/2" (DN15) through 2" (DN50)
End Connections:
•
Threaded — FNPT, BSPT, BSPP
•
ANSI Flanges — 150#, 300#
•
DIN Flanges — PN10/16, PN25/40
Size
Inches
Body Materials:
•
Ductile Iron
•
Bronze
•
Carbon Steel
•
Stainless Steel
Trim Materials:
•
303 SS for DI, BRZ & CS body valves
•
316SS for SS body valves
Seat Materials:
•
Jorcote on SST — Standard
•
Jorcote/Jordanic on SST — For severe service
•
Chrome Plated SST — Optional
Flow Coefficient
DN
Cv
Kv
1/2" &
3/4"
15 & 20
6.4
5,50
1/2"
15
7.0
6,02
3/4"
20
9.5
8,17
1" &
1-1/4"
25 & 32
15
12,90
1"
25
18
15,48
1-1/4"
32
25
21,50
1-1/2"
& 2"
40 & 50
30
25,80
1-1/2"
40
45
38,70
2"
50
50
43,00
PSI
SST
75
5,17
Jorcote
200
13,79
•
Size
1-1/2"
2"
Shutoff: ANSI Class IV
Action:
•
Direct (increase in temperature closes valve)
•
Reverse (increase in temperature opens valve)
SST
75
5,17
Jorcote
200
13,79
SST
75
5,17
Jorcote
200
13,79
SST
75
5,17
Jorcote
175
12,07
SST
75
5,17
Jorcote
175
12,07
SST
75
5,17
Jorcote
175
12,07
SST
75
5,17
Jorcote
175
12,07
SST
75
5,17
Jorcote
175
12,07
SST
75
5,17
175
12,07
Seat Material
PSI
BAR
SST
75
5,17
Jorcote
100
6,89
SST
75
5,17
Jorcote
100
6,89
Mark 802
Inches
Service: steam, water, oil, gas, air and chemicals
BAR
Jorcote
Yoke Material: Carbon Iron
Stem Packing Materials:
•
Spring-loaded Teflon (to 450°F max/232°C max)
•
Braided (above 500°F/260°C up to 650°F/343°C)
Max ∆P
Seat Material
Flow Coefficient
DN
40
50
Cv
65
70
Kv
55,9
60,2
Max ∆P
Available Temperature Control Ranges & Spans
Body Rating (Max):
•
Ductile Iron: 988 psi @ 100°F; 988 psi @ 450°F (68,1
bar @ 37,8°C; 68,8 bar @232,2°C)
•
Carbon Steel: 1480 psi @ 100°F; 1235 psi @ 450°F
(102,0 bar @ 37,8°C; 85,2 bar @ 232,2°C)
•
Stainless Steel: 1480 psi @ 100°F; 990 psi @ 450°F
(102,0 bar @ 37,8°C; 68,3 bar @ 232,2°C)
•
Bronze: 500 psi @ 100°F; 350 psi @ 450°F (34,5 bar
@ 37,8°C; 24,1 bar @ 232,2°C)
•
-20°F (-28,9°C) temperature limit on all materials
•
For other temperatures, consult factory
Overheat Protection: 100°F (38°C) above top of control
range
Range °F (°C)
Thermal Fill
Temperature span from
closed to open °F (°C)
w/standard spring*
1/2" - 3/4"
1" - 2"
(DN15-20) (DN25-32)
-10 to 20 (-23 to -7)**
Freon 22
18 (10)
30 (17)
20 to 55 (-7 to 13)
Freon R134A
20 (11)
32 (18)
45 to 90 (7 to 32)
Iso Butane
21 (12)
33 (18)
65 to 115 (18 to 46)
N-Butane
21 (12)
33 (18)
90 to 140 (32 to 60)
Ethyl Chloride
21 (12)
33 (18)
120 to 165 (49 to 74)
Freon R123
31 (17)
38 (21)
130 to 185 (54 to 85)
Ethyl Ether
31 (17)
38 (21)
170 to 225 (77 to 107)
Acetone
31 (17)
38 (21)
215 to 260 (102 to 127)
Isopropyl Alcohol
20 (11)
32 (18)
240 to 290 (116 to 143)
N-Proply Alcohol
21 (12)
33 (18)
275 to 325 (135 to 163)
N-Butyl Alcohol
21 (12)
33 (18)
325 to 400 (163 to 204)
Xylene
25 (14)
50 (28)
390 to 450† (199 to 232)
P-Cymene
25 (14)
50 (28)
* Lower spans and ranges available with optional light spring.
** Requires reinforced actuator
† Requires 1" x 17" bulb.
-8-
Mark 801/802 Self-Operated Temperature Regulators
Thermal System Specifications
Actuator: Type SWA
Capillary Material:
•
Standard — Copper
•
Optional — SST
Armor/Bulb Material:
•
Standard — SST with copper bulb
•
Optional — SST with SST bulb; Teflon with Teflon/
SST bulb
Capillary/Armor Length:
•
Standard — 8 feet (2,4 meters)
•
Optional — Lengths to 100 feet (30,5 meters)
Types of Bulbs:
•
Type A: Standard Bulb
•
Type B: Plain Bulb
•
Type C: Finned Bulb
•
Type D: Bulb with Rigid “Dead” Extension
•
Type E: Bulb with Pressure-tight Extension (well required for support when mounted horizontally)
•
Type F: Bulb Extension with Adjustable Union
Thermal Wells:
•
Type A: Standard Threaded Connection
•
Type B: Optional Flanged Connection
Standard Bulb Dimensions
Bulb Type
A&B
C
D, E & F
Nominal Bulb Size (Dia x Length) for ranges beginning:
101°F (38,3°C) or above
100°F (37,7°C) or below
1" x 14" (standard)
(2,5cm x 35,6cm)
1" x 17" (standard)
(2,5cm x 43,2cm)
3/4" x 27" (optional)
(1,9cm x 68,6cm)
3/4" x 33" (optional)
(1,9cm x 83,8cm)
1" x 14" (SST only)
(2,5cm x 35,6cm)
1" x 17" (SST only)
(2,5cm x 43,2cm)
1-1/8" x 14" (CU only)
(2,9cm x 35,6cm)
1-1/8" x 14" (CU only)
(2,9cm x 35,6cm)
1" x 14" (standard)
(2,5cm x 35,6cm)
1" x 17" (standard)
(2,5cm x 43,2cm)
-9-
Mark 801/802 Self-Operated Temperature Regulators
Dimensions
5" (114mm) Min
D
Flanged Ends
•
Size
1/2"
3/4"
B
1"
1-1/4"
1-1/2"
C
2"
A
A1
•
Threaded Ends
Size
Material
1/2" &
3/4"
DI/BRZ
1"
1-1/4"
1-1/2"
2"
•
Dimensions (inches)
A
B
C
D
Weight
(lbs.)
3.62
12.00
2.18
7.00
20
CS/SS
3.65
12.00
2.18
7.00
21
DI/BRZ
4.12
12.25
2.62
7.00
22
CS/SS
4.12
12.25
2.62
7.00
23
DI/BRZ
4.12
12.25
2.62
7.00
22
DI/BRZ
4.50
12.81
3.00
7.00
24
CS/SS
5.50
12.81
3.00
7.00
27
DI/BRZ
4.50
12.81
3.00
7.00
24
CS/SS
5.50
12.81
3.00
7.00
27
15
20
25
32
40
50
Threaded Ends, Metric
Size
(DN)
15 &
20
25
32
40
50
Material
DI/BRZ
Dimensions (mm)
A
B
C
D
Weight
(kg)
92
305
55
178
9,1
CS/SS
93
305
55
178
9,5
DI/BRZ
105
311
67
178
10,0
CS/SS
105
311
67
178
10,4
DI/BRZ
105
311
67
178
10,0
10,9
DI/BRZ
114
325
76
178
CS/SS
140
325
76
178
12,2
DI/BRZ
114
325
76
178
10,9
CS/SS
140
325
76
178
12,2
-10-
A1
B
Weight (lbs.)
C
D
DI/BRZ
CS/SS
150#
7.25
12.00
2.18
7.00
21
23
300#
7.50
12.00
2.18
7.00
22
24
150#
7.25
12.00
2.18
7.00
22
25
300#
7.62
12.00
2.18
7.00
23
28
150#
7.25
12.25
2.62
7.00
24
28
300#
7.75
12.25
2.62
7.00
25
30
150#
7.87
12.25
2.62
7.00
25
—
300#
8.37
12.25
2.62
7.00
26
—
150#
8.75
12.75
3.00
7.00
29
38
300#
9.25
12.75
3.00
7.00
31
42
150#
10.00
12.81
3.00
7.00
29
38
300#
10.50
12.81
3.00
7.00
31
42
Flanged Ends, Metric
Size
(DN)
•
Dimensions (inches)
ANSI
Flange
Dimensions (mm)
Weight (kg)
Flange
(PN)
A1
B
C
D
DI/BRZ
CS/SS
10/16
130
305
55
178
9,5
10,4
25/40
130
305
55
178
10
10,9
10/16
150
305
55
178
10
11,3
25/40
150
305
55
178
10,4
12,7
10/16
160
311
67
178
10,9
12,7
25/40
160
311
67
178
11,3
13,6
10/16
180
311
67
178
11,3
—
25/40
180
311
67
178
11,8
—
10/16
200
324
76
178
12,2
17,2
25/40
200
324
76
178
13,6
19,1
10/16
230
325
76
178
13,2
17,2
25/40
230
325
76
178
14,1
19,1
Mark 801/802 Self-Operated Temperature Regulators
Ordering Schematic
To specify a MK801/802 Series Temperature Regulator, build a model number by making a selection from each category in the Product Designator Coding System below.
1
—
1
2
—
3
/
4
5
6
7
8
9
10
5
Model
11
12
Trim
T3
303SS / Teflon Packing
High-Flow with Temperature Gauge
T6
316SS / Teflon Packing
Super High-Flow
TM
Monel / Teflon Packing
Super High-Flow with Temperature Gauge
TA
Alloy 20 / Teflon Packing
TH
Hastelloy C / Teflon Packing
I3
303SS / 287-I Packing
1/2" (DN15)
I6
316SS / 287-I Packing
075
3/4" (DN20)
IM
Monel / 287-I Packing
100
1" (DN25)
IA
Alloy 20 / 287-I Packing
125
1-1/4" (DN32)
IH
Hastelloy C / 287-I Packing
150
1-1/2" (DN40)
ZZ
Non-Standard
200
2" (DN50)
801
High-Flow
801T
802
802T
2
Size
050
3
Seats
6
Body Material
Material
Cv
Ductile Iron
A
303SST
K
6.1
Bronze
B
316SST
7
6.4
CS
Carbon Steel (WCB)
Q
303 / Teflon
L
7.0
S6
Stainless Steel (CF8M)
R
316 / Teflon
M
9.0
9.5
DI
BR
4
End Connections
S
Monel / Teflon
8
T
Alloy 20 / Teflon
Q
14
U
Hastelloy C / Teflon
9
15
PT
NPT
BT
BSPT
V
303SS / Jorcote
R
18
BP
BSPP
W
316SS / Jorcote
T
24
SW
FSW
X
303SS / Jorcote / Jordanic
A
25
F1
125# IFE
Y
316SS / Jorcote / Jordanic
B
30
I5
150# IFE
1
303SSt w/std. W.H.
V
35
F5
150# FE (except IFE)
2
316SST w/std. W.H.
W
45
F2
250# FE
C
50
I3
300# IFE
Y
65
F3
300# FE (except IFE)
E
70
I7
PN10 DIN IFE
F7
PN10 FE (except IFE)
I6
PN16 DIN IFE
F6
PN16 FE (except IFE)
I8
PN25 DIN IFE
F8
PN25 FE (except IFE)
I4
PN40 DIN IFE
F4
PN40 FE (except IFE)
ZZ
Non-Standard
ZZ
Non-Standard
Continued on page 12.
-11-
MK80/1012/5K/AB
Mark 801/802 Self-Operated Temperature Regulators
Ordering Schematic (Cont'd)
Range
7
Standard Spring °F
Standard Spring °C
08
-10 to 20*
A8
-23 to 7
14
20 to 55
B4
-7 to 13
23
45 to 90
C3
7 to 32
30
65 to 115
DD
18 to 46
37
90 to 140
D7
32 to 60
47
20 to 165
E7
49 to 74
52
130 to 185
F2
54 to 85
60
170 to 225
GG
77 to 107
68
215 to 260
G8
102 to 127
75
240 to 290
H5
116 to 143
84
275 to 325
J4
90
325 to 400
95
390 to 450
ZZ
Type & Material
Diameter x Length
A
Type A, Cu
2
1" x 14"
(24,5mm x 355,6mm)
G
Type A, SST
3
1" x 17"
(24,5mm x 431,8mm)
H
Type B, SST
J
Teflon Coated B
ZZ
Non-Standard
Type C Bulb
C9
Type C, Cu
1-1/8" x 14"
(28,6mm x 355,6mm)
135 to 163
C2
Type C, SST
KK
163 to 204
1" x 14"
(24,5mm x 355,6mm)
K5
199 to 232
ZZ
Non-Standard
Non-Standard
Light Spring °F
Light Spring °C
Capillary / Armor
10
Material
Length
07
-15 to -5*
A7
-26 to -21
13
15 to 35
B3
-9 to 2
21
40 to 70
C1
41 to 21
28
60 to 90
C8
16 to 32
36
85 to 115
D6
29 to 46
44
115 to 140
E4
52 to 60
50
125 to 160
FF
46 to 71
56
155 to 200
F6
68 to 93
65
205 to 235
G5
96 to 113
73
235 to 270
H3
113 to 132
A
Standard
83
270 to 300
J3
132 to 149
R
SWA / Reinforced required below 0°F (18°C)
89
320 to 370
J9
160 to 188
ZZ
Non-Standard
94
385 to 440
K4
196 to 227
* Reinforced actuator required
A
Cu
1
8' (2,4m)
B
SST
2
10' (3,0m)
T
Teflon Coated
3
12' (3,7m)
4
15' (4,6m)
5
20' (6,1m)
ZZ
11
Size: for Bulb Diameter x Length
Type, Fitting & Material
A
Type A, 1" NPT, Cu
B
1" x 14"
(24,5mm x 355,6mm)
B
Type A, 1" NPT, SST
C
1" x 17"
(24,5mm x 431,8mm)
E
Type B, 1-1/2" x 150#, SST
F
Type B, 1-1/2" x 300#, SST
G
Type B, 2" x 150#, SST
H
Type B, 2" x 300#, SST
NN
None
ZZ
Non-Standard
Non-Standard
Actuator
12
Thermowell
8
Bulb
9
Action
D
Direct
R
Reverse
Tank Fitting Only
11
1" NPT Brass for 1" Bulb
12
1" NPT SST for 1" Bulb
NN
None
ZZ
Non-Standard
Jordan Valve, a division of Richards Industries
3170 Wasson Road • Cincinnati, OH 45209
513.533.5600 • 800.543.7311 • 513.871.0105 (f)
[email protected] • www.jordanvalve.com
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement