Delfield NDF-18 Installation manual

Delfield NDF-18 Installation manual
Shelleymatic®
by Delfield
Milk, Ice Cream and Milk & Ice Cream Dispensers
Service and Installation Manual
Please read this manual completely before attempting to install or operate this equipment! Notify carrier of damage! Inspect all
components immediately.
N, N6/N10/N14
Free-standing milk or
beverage dispensers
NSCF, SCF
Free-standing ice cream
dispensers and milk & ice
cream dispensers
NDF
Free-standing milk or
beverage dispensers
NLFAC
Free-standing milk or beverage
dispensers with air curtain
MF, MFSC
Built-in milk or beverage
dispensers
Important Information
Read Before Use
Please Save These Instructions!
May 2013
Milk, Ice Cream & Milk & Ice Cream Dispensers Service and Installation Manual
Important Warning And Safety Information
WARNING
Read This Manual Thoroughly Before Operating, Installing, Or Performing Maintenance On The Equipment.
WARNING
Failure To Follow Instructions In This Manual Can Cause Property Damage, Injury Or Death.
WARNING
Do Not Store Or Use Gasoline Or Other Flammable Vapors Or Liquids In The Vicinity Of This Or Any Other
Appliance.
WARNING
Unless All Cover And Access Panels Are In Place And Properly Secured, Do Not Operate This Equipment.
WARNING
This Appliance Is Not Intended For Use By Persons Who Lack Experience Or Knowledge, Unless They Have
Been Given Supervision Or Instruction Concerning Use Of The Appliance By A Person Responsible For Their
Safety.
WARNING
This Appliance Is Not To Be Played With.
Warning
Do Not Clean With Water Jet.
WARNING
Do Not Use Electrical Appliances Inside The Food Storage Compartment Of This Appliance.
CAUTION
Observe the following:
2
•
Minimum clearances must be maintained from all walls and combustible materials.
•
Keep the equipment area free and clear of combustible material.
•
Allow adequate clearance for air openings.
•
Operate equipment only on the type of electricity indicated on the specification plate.
•
Unplug the unit before making any repairs.
•
Retain this manual for future reference.
For customer service, call (800) 733-8829, (800) 773-8821, Fax (989) 773-3210, www.delfield.com
Milk, Ice Cream & Milk & Ice Cream Dispensers Service and Installation Manual
Contents
Receiving and Inspecting Equipment......................................... 3
Serial Number Location.............................................................. 4
Warranty Information.................................................................. 4
Regulatory Certifications............................................................. 4
Specifications.............................................................................. 5
Installation................................................................................6-7
Operation..................................................................................... 8
Maintenance................................................................................ 9
Wiring Diagram.........................................................................10
Replacement Parts...............................................................11-17
Standard Labor Guidelines.......................................................18
Notes.........................................................................................19
Receiving and Inspecting the Equipment
Even though most equipment is shipped crated, care should be
taken during unloading so the equipment is not damaged while
being moved into the building.
1. Visually inspect the exterior of the package and skid or
container. Any damage should be noted and reported to
the delivering carrier immediately.
2. If damaged, open and inspect the contents with the
carrier.
3. In the event that the exterior is not damaged, yet upon
opening, there is concealed damage to the equipment
notify the carrier. Notification should be made verbally as
well as in written form.
4. Request an inspection by the shipping company of the
damaged equipment. This should be done within 10 days
from receipt of the equipment.
5. Check the lower portion of the unit to be sure casters are
not bent.
6. Also open the compressor compartment housing and
visually inspect the refrigeration package. Be sure lines
are secure and base is still intact.
7. Freight carriers can supply the necessary damage forms
upon request.
8. Retain all crating material until an inspection has been
made or waived.
Uncrating the Equipment
First cut and remove the banding from around the crate.
Remove the front of the crate material, use of some tools will
be required. If the unit is on legs remove the top of the crate
as well and lift the unit off the skid. If the unit is on casters it
can be rolled off the skid.
For customer service, call (800) 733-8829, (800) 773-8821, Fax (989) 773-3210, www.delfield.com
3
Milk, Ice Cream & Milk & Ice Cream Dispensers Service and Installation Manual
Serial Number Location
Serial number tag locations
MF/MFSC — on the end above the refrigeration system.
N, N6/N10/N14, and SCF — rear of the unit above the louver.
NDF — Front right hand corner under the lid.
NLFAC — at the rear of the unit by the power cord.
Always have the serial number of your unit available when calling
for parts or service. A complete list of authorized Delfield parts
depots is available at www.delfield.com.
The units represented in this manual are for indoor use only.
©2013 The Delfield Company. All rights reserved. Reproduction without
written permission is prohibited. “Delfield” and “Shelleymatic” are registered
trademarks of The Delfield Company.
Warranty Information
Visit http://www.delfield.com/minisite/service/warranty_info to:
• Register your product for warranty.
• Verify warranty information.
• View and download a copy of your warranty.
Regulatory Certifications
All models are certified by:
National Sanitation Foundation (NSF)
Underwriters Laboratories (UL)
4
For customer service, call (800) 733-8829, (800) 773-8821, Fax (989) 773-3210, www.delfield.com
Milk, Ice Cream & Milk & Ice Cream Dispensers Service and Installation Manual
Specifications
Model
H.P.
Loading/Dispensing
Weight
(lbs)
Amps
(115V)
NEMA Plug
BTU Load
Evap BTU/
TD
BTU
Capacity
Ref/Charge
Self-contained free-standing milk or beverage dispensers
N-520
1/4
sliding top lids
327
5.0
5-15P
189
33/31º
1035
134a/16oz
N-860
1/4
sliding top lids
392
5.0
5-15P
259
42/28º
1167
134a/16oz
N-1200
1/4
sliding top lids
462
5.0
5-15P
328
51/25º
1273
134a/16oz
N-1530
1/4
sliding top lids
532
5.0
5-15P
398
60/23º
1360
134a/16oz
N6-1313-34
1/4
sliding top lids
382
5.0
5-15P
245
42/28º
1167
134a/16oz
N6-1313-36
1/4
sliding top lids
402
5.0
5-15P
245
42/28º
1167
134a/16oz
N10-1313-34
1/4
sliding top lids
545
5.0
5-15P
353
55/24º
1315
134a/16oz
N10-1313-36
1/4
sliding top lids
565
5.0
5-15P
353
55/24º
1315
134a/16oz
N14-1313-34
1/4
sliding top lids
650
5.0
5-15P
455
68/21º
1422
134a/16oz
N14-1313-36
1/4
sliding top lids
670
5.0
5-15P
455
68/21º
1422
134a/16oz
Self-contained free-standing milk or beverage dispensers
NDF-12
1/4
drop front & flip top lids
365
5.0
5-15P
687
49/25º
1204
134a/16oz
NDF-18
1/3
drop front & flip top lids
430
7.0
5-15P
898
60/27º
1585
134a/24oz
Self-contained free-standing milk or beverage dispensers with air curtain (BTU is with lids closed.)
NLFAC-8
1/3
hinged lids w/air curtain
401
7.0
5-15P
668
140/16º
2184
134a/24oz
NLFAC-12
1/2
hinged lids w/air curtain
491
9.0
5-15P
859
140/21º
2885
134a/32oz
NLFAC-16
1/2
hinged lids w/air curtain
583
11.0
5-15P
1050
140/23º
3193
134a/32oz
390
7.1
5-15P
139(ref)
414(frz)
37/43º(ref)
37/21º(frz)
1596(ref)
796(frz)
404A/16oz
Self-contained free-standing milk and ice cream dispensers
NSCF-48
1/4
hinged top lids
Self-contained free-standing ice cream dispensers
SCF-32
1/4
hinged top lids
334
7.1
5-15P
709
51/18º
915
404A/16oz
SCF-48
1/3
hinged top lids
414
8.0
5-15P
1043
69/19º
1350
404A/24oz
Model
H.P.
Cutout Dim. (L x D)
Weight
(lbs)
Amps
(115V)
NEMA Plug
BTU Load
Evap BTU/
TD
BTU
Capacity
Ref/Charge
Self-contained built-in milk or beverage dispensers *a 2.87” space is required between each cutout
MFSC-2020
1/4
(1) 25.25” x 22.25”
303
5.0
5-15P
304
51/24º
1223
134a/16oz
MFSC-2821
1/4
(1) 10.75” x 21”
267
5.0
5-15P
264
45/26º
1166
134a/16oz
MFSC-31
1/4
(2) 10.75” x 21”*
306
5.0
5-15P
296
50/24º
1212
134a/16oz
MFSC-44
1/4
(3) 10.75” x 21”*
413
5.0
5-15P
408
64/21º
1346
134a/16oz
MFSC-57
1/4
(4) 10.75” x 21”*
461
5.0
5-15P
519
79/18º
1447
134a/16oz
Remote built-in milk or beverage dispensers *a 2.87” space is required between each cutout
MF-2020
N/A
(1) 25.25” x 22.25”
240
N/A
N/A
304
51/24º
N/A
134a/N/A
MF-2821
N/A
(1) 10.75” x 21”
197
N/A
N/A
264
45/26º
N/A
134a/N/A
MF-31
N/A
(2)10.75” x 21”*
238
N/A
N/A
296
50/24º
N/A
134a/N/A
MF-44
N/A
(3)10.75” x 21”*
312
N/A
N/A
408
64/21º
N/A
134a/N/A
MF-57
N/A
(4) 10.75” x 21”*
335
N/A
N/A
519
79/18º
N/A
134a/N/A
For customer service, call (800) 733-8829, (800) 773-8821, Fax (989) 773-3210, www.delfield.com
5
Milk, Ice Cream & Milk & Ice Cream Dispensers Service and Installation Manual
Installation
Location
These units are intended for indoor use only. Be sure the location
chosen has a floor strong enough to support the total weight of
the cabinet and contents. Units in this product line can weigh as
much as 1500 pounds when it is fully stocked. Reinforce the
floor as necessary to provide for maximum loading.
For the most efficient refrigeration, be sure to provide good air
circulation inside and out.
Inside cabinet: Do not pack unit so full that air cannot circulate.
Take care not to block air flow to the fans and allow space along
sides.
Outside cabinet: Be sure that the unit has access to ample
air. Avoid hot corners and locations near stoves and ovens. It
is recommended that the rear of the unit be no less than two
inches from any wall, partition or any other object which will
restrict exhaust air flow.
Leveling
A level cabinet looks better and will perform better because
the cabinet will not be subject to unnecessary strain due to
doors not properly lining up with door frames.
Some models have casters for ease of cleaning underneath and
for mobility. It is important that the unit be installed in a stable
condition with the front casters locked before operating. Locking
the front casters after installation is the operator’s responsibility.
Electrical connection
A standard self-contained unit is provided with a power cord
and three-prong grounded plug.
The unit should be plugged into a receptacle with its own
circuit protection that matches the amperage of the plug.
Refer to the amperage data on specifications
page or the serial tag data and your local code or
the National Electrical Code to be sure the unit is
connected to the proper power source. A protected
circuit of the correct voltage and amperage must
be run for connection to the unit.
Built-in units
All self-contained units (MFSC) are tested at the factory to assure
proper operation. The unit should not be installed directly next to
high heat generating equipment (ranges, griddles, etc.).
These units are built into the counter from below and must be
supported from the bottom. The counter cut-out sizes and power
supply requirements are shown on the specifications page. All
refrigerators have drains located in the bottom of the tank. An
appropriate drainage area or container must be provided by
the customer. Be sure to place the unit so the pressure control,
located near the compressor, can be reached.
For installation of remote units (MF), consult a refrigeration
service company to connect refrigeration lines to the remote
condensing unit.
Self-contained refrigerated units (MFSC) require
air flow to the compressor. A louver is provided
and must be installed in the counter in front of the
condenser. An equal size opening at the rear of
the cabinet must also be provided to allow warm
air to escape. Failure to do so will void all product
warranties.
Free standing units
All self-contained units (N, N6/10/14, NDF, NLFAC, SCF and
NSCF) are tested at the factory to assure proper operation. The
unit should not be installed directly next to high heat generating
equipment (ranges, griddles, etc.).
These units are free standing, either on legs or casters. The
power supply requirements are shown on the specifications
page. All free standing units have drains located in the bottom
of the tank. An appropriate drainage area or container must be
provided by the customer.
Do not place the unit against a wall or any object that will block
air circulation through the condensing unit. If the unit must
be placed against a wall, leave a minimum of 2” of space for
air flow.
The power supply must be disconnected
whenever performing maintenance or repairing
the equipment!
The unit must never be operated without the
louvered panel in place.
6
For customer service, call (800) 733-8829, (800) 773-8821, Fax (989) 773-3210, www.delfield.com
Milk, Ice Cream & Milk & Ice Cream Dispensers Service and Installation Manual
Installation Continued
How to adjust self-leveling dispenser
Tools Needed: One small flat head screw driver; One Phillips
head screw driver.
1. A
lways wear safety glasses when adjusting your dispenser.
Also, lock brakes on mobile units before beginning.
2. U
nload dispenser and remove stainless steel load tray by
lifting straight up and set it aside (see figure 1).
RETAINER
(Figure 1) Sample unit
LOAD TRAY
RETAINER
ELEVATOR HOUSINGS
3. U
se small regular screw driver to loosen each retainer
mounted on stainless steel rod at top of each elevator
housing.
4. To
remove
elevator housing,
lift
housing
straight up to
clear the stud on
unit base. Then
gently swing the
bottom of the
housing towards
the inside of the
unit and pull
housing out of the
unit (see figure 2).
Lay housing on
flat surface.
5. U
se Phillips head
screw driver to
remove front panel
on the elevator
housing (see figure
3).
6. If carrier is riding
too high, you need
to remove springs.
With carrier all the
way to the top, gently
disengage one spring
at a time, unhooking
bottom loop out of
carrier bracket (see
figure 4). Remove
as many springs as
necessary.
If carrier is riding too
low, you need to add
springs. With carrier
all the way to the top,
gently engage one
spring at a time by
hooking bottom loop
of spring into carrier
bracket. Add as many
springs as necessary.
REMOVE SCREWS,
SLIDE COVER OFF
(Figure 3) Remove front panel
REMOVE OR
ADD SPRINGS
AS NEEDED
(Figure 4) Remove or add springs
7. W
hen finished, put elevator housing back in unit and put
stainless steel load tray back on elevator housings. Load
unit to test dispensing level. If spring adjustment does
not position carrier properly, repeat procedure #6 trying
different springs. If this does not work, a different set
of springs may be required. To order, call The Delfield
Company Parts and Service Department at 800.733.8829
8. I f level is appropriate, put front panels back on and
tighten retainer.
CAUTION: Dispenser should not be operated
with front panels off elevator housing.
OTE: When adjusting the elevators make sure each have the
N
same number and size of springs connected to the carrier on
both sides. This will prevent the load tray from binding.
(Figure 2) Remove elevator housing
For customer service, call (800) 733-8829, (800) 773-8821, Fax (989) 773-3210, www.delfield.com
7
Milk, Ice Cream & Milk & Ice Cream Dispensers Service and Installation Manual
Operation: N, N6/10/14, NDF, NLFAC, MF & MFSC Series
N, N6/10/14, NDF, NLFAC and MFSC Series milk dispensers
are set at the factory to maintain temperatures between 36°F
and 40°F. No further adjustment should be necessary. To begin
operation on self-contained models, plug the electrical supply
cord into a receptacle with the correct voltage. Remote models
will require a connection to a separate refrigeration system.
Loading: N, MF & MFSC Series
To load, place a complete layer of cartons or bottles standing
upright on the load tray. Then place a divider tray on top of
this layer, then another layer of cartons or bottles on this tray,
then another tray and another layer, etc. As each additional
tray is loaded, the elevators gradually lower. The last layer
may be placed on top without the use of another tray. When
loading the average tall half pint bottles, four layers may be
loaded into each compartment standing upright and the fifth
layer laying down.
It is very important to use the divider trays
provided between each successive layer of
contents to assure the correct balance of the
load and the proper action of the elevating
mechanism.
Wire racks, when used, should be loaded completely. When
placing one rack on top of the other, be sure the stacking lugs
are properly aligned.
Loading: N6/10/14 Series
These cabinets are designed to dispense 13” x 13” x 11” high
(maximum dimensions) dairy cases. Place one case loaded
with milk on the carrier and then place a second case loaded
with milk on top of the first case. Press down on the cases
leaning them toward the retaining bracket located under the
top lid track, then gradually release pressure on the cases
so that the top edge of the case engages with the retaining
bracket.
The elevating mechanism is designed to keep the contents
several inches below the top of the cabinet when fully loaded.
This distance serves two purposes:
A. It keeps the top layer of milk completely refrigerated even
when the lids are removed.
B. It insures that the lids will operate without striking the
contents as successive layers are added.
Loading: NDF Series
These cabinets are designed to dispense 13” x 13” x 11” high
(maximum dimensions) dairy cases. They do not have a selfleveling mechanism. Simply place the cases on top of each
other inside the cabinet through the wide opening in the top
and front.
Loading: NLFAC Series
These cabinets are designed to dispense 13” x 13” x 11” high
(maximum dimensions) dairy cases. Model NLFAC-8 holds
eight cases; four on the bottom and four on the top. Model
NLFAC-12 holds twelve cases; six on the bottom and six on
the top. Model NLFAC-16 holds sixteen cases, eight on the
bottom and eight on the top.
Milk cases are loaded through the wide opening in the top and
front of the unit. Fold the hinged lids up and back and rest
them on the top. The cabinet interior has self-locating guides
installed to make loading easy.
Operation: SCF & NSCF series
SCF Series ice cream dispensers are set at the factory to
maintain temperatures between -5°F and 0°F. NSCF Series
combination milk and ice cream dispensers are set at the
factory to maintain temperatures between 36°F and 40°F for
refrigerated product and between -5°F and 0°F for frozen
product. Each combination unit is constructed with two tanks
and separate controls. No further adjustments should be
necessary. To begin operation plug the electrical supply cord
into a receptacle with the correct voltage.
Loading
To load, place two layers of ice cream on the load tray, then a
tray, two additional layers of ice cream, then another tray, etc.
Do not stack ice cream above the frost line on the interior of
the freezer. See the instructions for the MF units (above) for
loading the refrigerated portion of the combination units.
Temperature Control
NLFAC Thermostat Control
Set the thermostat toward 1 for
higher temperatures and toward
7 for lower temperatures. The
refrigerator factory setting is 4
and maintains 38ºF (3ºC) in the
box.
8
Low Pressure Control, Remaining Self Contained Models
If it is necessary to adjust the temperature, turn the knob
clockwise as indicated on the control. Make adjustments
gradually. It may take an hour to realize the temperature
change. Milk or beverage dispenser factory settings are 17ºF
differential, 34ºF cut in, and 17ºF cut out. Milk and ice cream
dispenser factory settings are 25ºF differential, 30ºF cut in, and
5ºF cut out.
For customer service, call (800) 733-8829, (800) 773-8821, Fax (989) 773-3210, www.delfield.com
Milk, Ice Cream & Milk & Ice Cream Dispensers Service and Installation Manual
Maintenance
Door Gasket Maintenance
Door gaskets require regular cleaning to prevent mold and mildew build up
and also to retain the elasticity of the gasket. Gasket cleaning can be done
with the use of warm soapy water. Avoid full strength cleaning products
on gaskets as this can cause them to become brittle and crack. Never
use sharp tools or knives to scrape or clean the gasket. Gaskets can be
easily replaced and do not require the use of tools or an authorized service
person. The gaskets are “Dart” style and can be pulled out of the groove in
the door and new gaskets can be “pressed” back into place.
Drain Maintenance - Base
Each unit has a drain located inside the unit that removes the condensation
from the evaporator coil and routes it to an external condensate evaporator
pan. Each drain can become loose or disconnected during normal use.
If you notice water accumulation on the inside of the unit be sure the
drain tube is connected to the evaporator drain pan. If water is collecting
underneath the unit make sure the end of the drain tube is in the
condensate evaporator in the machine compartment. The leveling of the
unit is important as the units are designed to drain properly when level. Be
sure all drain lines are free of obstructions.
Caster Maintenance
Wipe casters with a damp cloth monthly to prevent corrosion.
The power switch must be turned to OFF and the unit
disconnected from the power source whenever performing
service, maintenance functions or cleaning the refrigerated
area.
Refrigerators and Freezers
The interior and exterior can be cleaned using soap and warm water. If
this isn’t sufficient, try ammonia and water or a nonabrasive liquid cleaner.
When cleaning the exterior, always rub with the “grain” of the stainless
steel to avoid marring the finish. Do not use an abrasive cleaner because
it will scratch the stainless steel and can damage the breaker strips and
gaskets.
Stainless Steel Care and Cleaning
To prevent discoloration or rust on stainless steel several important
steps need to be taken. First, we need to understand the properties of
stainless steel. Stainless steel contains 70- 80% iron, which will rust. It
also contains 12-30% chromium, which forms an invisible passive film
over the steels surface, which acts as a shield against corrosion. As long
as the protective layer is intact, the metal is still stainless. If the film is
broken or contaminated, outside elements can begin to breakdown the
steel and begin to form discoloration of rust. Proper cleaning of stainless
steel requires soft cloths or plastic scouring pads.
NEVER USE STEEL PADS, WIRE BRUSHES OR SCRAPERS!
Cleaning solutions need to be alkaline based or non-chloride cleaners.
Any cleaner containing chlorides will damage the protective film of the
stainless steel. Chlorides are also commonly found in hard water, salts,
and household and industrial cleaners. If cleaners containing chlorides are
used be sure to rinse repeatedly and dry thoroughly. Routine cleaning of
stainless steel can be done with soap and water. Extreme stains or grease
should be cleaned with a non-abrasive cleaner and plastic scrub pad.
Always rub with the grain of the steel. There are stainless steel cleaners
available which can restore and preserve the finish of the steels protective
layer. Early signs of stainless steel breakdown are small pits and cracks. If
this has begun, clean thoroughly and start to apply stainless steel cleaners
in attempt to restore the passivity of the steel.
Never use an acid based cleaning solution! Many food
products have an acidic content, which can deteriorate the
finish. Be sure to clean the stainless steel surfaces of ALL
food products. Common items include, tomatoes, peppers
and other vegetables.
Cleaning the Condenser Coil
In order to maintain proper refrigeration performance, the condenser fins
must be cleaned of dust, dirt and grease regularly. It is recommended that
this be done at least every three months. If conditions are such that the
condenser is totally blocked in three months, the frequency of cleaning
should be increased. Clean the condenser with a vacuum cleaner or stiff
brush. If extremely dirty, a commercially available condenser cleaner may
be required.
Failure to maintain a clean condenser coil can initially cause high
temperatures and excessive run times. Continuous operation with a dirty
or clogged condenser coil can result in compressor failure. Neglecting the
condenser coil cleaning procedures will void any warranties associated
with the compressor and cost to replace the compressor.
Never use a high-pressure water wash for this cleaning
procedure as water can damage the electrical components
located near or at the condenser coil.
Preventing blower coil corrosion
To help prevent corrosion of the blower coil, store all acidic items, such
as pickles and tomatoes, in sealable containers. Immediately wipe up all
spills.
Cleaning the condensate evaporator (remote models only)
The stainless steel condensate evaporator pan should be cleaned every
six months. Use a vacuum cleaner or damp cloth to remove dust that may
have accumulated. This will prevent corrosion of the stainless steel.
Defrosting
Milk or Ice Cream dispensers require defrosting after 3/8” to 1/2” of frost
forming. On/Off switch is located above the louver panel.
Never use sharp objects or tools to clean or scrape ice/frost build up. A
puncture could cause irreparable damage to the refrigeration system.
Cleaning the NLFAC milk dispensers
The following special instructions apply to the model NLFAC dispenser
only. After cleaning the interior and exterior as described above, be sure
to return the milk case loading tray to the bottom of the unit. The load tray
is required not only for easy self-locating of milk cases, but it also ensures
proper air flow through the evaporator coil for the air curtain.
Any restriction to the air flow path, including leaving the
milk case load tray out of the cabinet, will result in the
voiding of your warranties.
A drain is supplied to simplify cleaning of the interior. Open
the clamp used to close off the drain tube. Drain accumulated liquid from
the cabinet. Be sure to re-clamp the tubing before resuming operation of
the NLFAC unit.
Air Diffuser Cleaning Procedure
The air diffuser is located on the inside wall by the evaporator fans.
Remove the air diffuser from the equipment. Soak in fresh hot dishwater
for five minutes. Rinse by spraying soap off with warm water, directing the
spray into the holes. Repeat rinsing steps until material is visibly clean.
Soak in sanitizing solution for five minutes. Replace into equipment.
For customer service, call (800) 733-8829, (800) 773-8821, Fax (989) 773-3210, www.delfield.com
9
Milk, Ice Cream & Milk & Ice Cream Dispensers Service and Installation Manual
Wiring Diagrams
Model — MFSC
L1
N
G
N
G
Condensing Unit
Pressure Control
Models — N, SCF, NSCF, & NDF
L1
Condensing Unit
On/off Switch
Pressure Control
Model — NLFAC
L1
N
Condensing Unit
Thermostat
10
Evap. Fans
For customer service, call (800) 733-8829, (800) 773-8821, Fax (989) 773-3210, www.delfield.com
G
Milk, Ice Cream & Milk & Ice Cream Dispensers Service and Installation Manual
Replacement Parts
NLFAC8
3516101
Drier, Filter, 1/4ODF
3516172
Blade, fan, evaporator
3516173
Guard, Plastic, Fan, 6”
*377-AZ0-0004
Bolt, Lock
3234684
Lock Assembly, Glass Door
031-264-0000
Bracket, Evaporator Fan Motor
*359-411-0041
Louver, 13.00 X 25.00
3234783
Caster, 5, Plate, Swivel, Break
2162691
Motor, Fan, 115V, 50/60
3234156
Catch, Magnetic, Snap-In
2190154
Switch, Rocker, 20A/125V
3516065
Coil, Evaporator, 3.00” X 24.75”
2194791
Thermometer Cable, Danfoss
AE630AT-602-J7
Compressor
2194792
Thermometer Display, Digital, Danfoss
3526675
Condensing Unit, 1/3HP, Hi, R134A
6230008
Track, Door, 50.21,PVC,BLACK
2183348
Cord, power, 16/3 W/Nema 5-15P
3516062
Valve, Expansion, R134A, RFG
*000-BI7-0033
Cover assembly, NLFAC8
NLFAC16
6230017
Hinge, aluminum in-between
000-282-0054
Assembly, Control, Thermostat
6230020
Hinge, aluminum
3516172
Blade, fan, evaporator
6230110
Hinge, plastic insert
*377-AZ0-0004
Bolt, Lock
*271-BGF-0003
Divider, Milk Crate, NLFAC
031-264-0000
Bracket, Fan Motor
3516101
Drier, Filter, 1/4ODF
3234783
Caster, 5, Plate, Swivel, Break
3516173
Guard, Plastic, Fan
3234156
Catch, Magnetic, Snap-In
3234684
Lock Assembly, Glass Door
3516065
Coil, Evaporator, 3.00 X 24.75
*359-411-0041
Louver, 13.00” X 25.00”
3527024
Compressor, AK169AT-038-J7, Tecumseh
2162691
Motor, evaporator, 115V,50/60
3526689
Condensing Unit, 1/2HP, Hi, R134A
2190154
Switch, Rocker, 20A/125V,
2183348
Cord, power, 16/3 W/Nema 5-15P
2194791
Thermometer Cable, Danfoss
*000-BI7-0035
Cover Assembly, Lift, NLFAC-16
2194792
Thermometer Display, Digital, Danfoss
6230019
Hinge, Aluminum, In Between
000-282-0054
Thermostat control
6230020
Hinge, Aluminum, Heavy Duty
6230007
Track, Door, 36.21, PVC, Black
6230110
Hinge, Insert, Plastic
3516062
Valve, Expansion, R134A
NLFAC12
*271-BGF-0003
Divider, Milk Crate, NLFAC
3516101
Drier, Filter, 1/4ODF
000-282-0054
Assembly, Control, Thermostat
3516173
Guard, Plastic, Fan, 6”
3516172
Blade, fan, evaporator
3234684
Lock Assembly, Glass Door
*377-AZ0-0004
Bolt, Lock
*359-411-0041
Louver, 13.00 X 25.00
031-264-0000
Bracket, Fan Motor
2162691
Motor, Fan, 115V, 50/60
3234783
Caster, 5, Plate, Swivel, Break
2190154
Switch, Rocker, 20A/125V
3234156
Catch, Magnetic, Snap-In
2194791
Thermometer Cable, Danfoss
3516065
Coil, Evaporator, 3.00 X 24.75
2194792
Thermometer Display, Digital, Danfoss
3527025
Compressor, AK168AT-038-J7, Tecumseh
6230009
Track, Door, 64.21, PVC, Black
3526688
Condensing Unit, 1/2HP, Hi, R134A
3516062
Valve, Expansion, R134A, RFG
2183348
Cord, power, 16/3 W/Nema 5-15P
*000-BI7-0034
Cover Assembly, Lift, NLFAC-12
6230018
Hinge, aluminum in-between 24.0”
6230020
Hinge, Aluminum, Heavy Duty
6230110
Hinge, Insert, Plastic
*271-BGF-0003
Divider, Milk Crate, NLFAC
* Part print on page 17.
** Condenser Assembly on page 15.
† Elevator Assembly on page 16.
For customer service, call (800) 733-8829, (800) 773-8821, Fax (989) 773-3210, www.delfield.com
11
Milk, Ice Cream & Milk & Ice Cream Dispensers Service and Installation Manual
Replacement Parts
N-520, 860, 1200 & 1530
000-AYP-0031
Lid Assembly, Top Sliding, N10
*265-774-0039
Carrier, elevator
000-AYP-0032
Lid Assembly, Top Sliding, N14
AE540AT-238-J7
Compressor, Tecumseh
3234105
Locknut/Washer, 1” Drain
3526674
Condensing Unit, 1/4HP, Hi, R134A
*359-AZD-0000
Louver, 13.5 x 9
2183348
Cord, power, 16/3 W/Nema 5-15P
*359-AZD-0001
Louver, 13.5 x 13
*030-392-0030
Divider, Tray
*359-411-000C
Louver, 25 x 13
3234065
Drain, 1” brass, 4” long, w/locknut and washer
2193927
Pressure control
6690493
Drain, Valve, 3/4 NPT
2190154
Switch, Rocker, 20A/125V
3516101
Drier, Filter, 1/4ODF
3516062
Valve, Expansion, R134A, RFG
†000-546-0036
Elevator assembly, 12.6” High (on condensing
unit side)
NDF-12
†000-546-0030
Elevator assembly, 24.41” High
6230170
Bumper, Corner, Small, PVC
3234110
Handle, lid, N-520/860/1200/1530
3234180
Caster, 4, Plate, Swivel, Break
3234645
Leg, 6”
3234307
Catch, Door
000-AYP-0037
Lid, sliding, bottom, N-520/860/1530
AE540AT-238-J7
Compressor - Tecumseh
000-AYP-0038
Lid, sliding, bottom, N-1200/1530
3526674
Condensing Unit, 1/4HP, Hi, R134A
000-AYP-0035
Lid, sliding, top, N-520/860
2193927
Control, Pressure, Low
000-AYP-0036
Lid, sliding, top, N-1200/1530
2183348
Cord, Lead, 16/3 W/Nema 5-15P
3234105
Locknut/Washer,1 Drain
3234242
Drain, Plastic, 1IPS, 2.87
*359-AZD-0000
Louver, 13.5” x 9”
6690493
Drain, Valve, 3/4” NPT
*359-AZD-0001
Louver, 13.5” x 13”
3516101
Drier, Filter, 1/4”ODF
*359-411-000C
Louver, 25” x 13”
6700007
Gasket, Snap-In
2193927
Pressure control
000-BOV-0031
Hinge, Pin Assembly, Right Hand
2190154
Switch, Rocker, 20A/125V,
000-BOV-0030
Hinge/Pin Assembly, Left Hand
3516062
Valve, Expansion, R134A, RFG,
000-BOM-0032
Lid Assembly, Front, NDF-12
000-BOM-0030
Lid Assembly, Top, NDF-12
6230003
Lock, Key, Lid, NDF/NDFA
*359-AZD-0030
Panel, Access, NDF-12
3516059
Thermometer, Digital
3516062
Valve, Expansion, R134A, RFG
N6-N10-N14
*265-774-003A
Carrier, N6, N10, N14
AE540AT-238-J7
Compressor - Tecumseh
3526674
Condensing Unit, 1/4HP, Hi, R134A
2183348
Cord, power, 16/3 W/Nema 5-15P
3234065
Drain, 1” brass, 4” long, w/ locknut and washer
6690493
Drain, Valve, 3/4” NPT
3516101
Drier, Filter, 1/4”ODF,
†000-546-0035
Elevator assembly, 22.57” high
3234110
Handle, lid, N6/10/14
3234645
Leg, 6”
000-AYP-0033
Lid Assembly, Bottom Sliding, N6
000-AYP-0034
Lid Assembly, Bottom Sliding, N10/14
000-AYP-0030
Lid Assembly, Top Sliding, N6
* Part print on page 17.
** Condenser Assembly on page 15.
† Elevator Assembly on page 16.
12
For customer service, call (800) 733-8829, (800) 773-8821, Fax (989) 773-3210, www.delfield.com
Milk, Ice Cream & Milk & Ice Cream Dispensers Service and Installation Manual
Replacement Parts
NDF-18
SCF-32
6230170
Bumper, Corner, Small, PVC
372-395-0000
Carrier, Large Ice Cream
3234180
Caster, 4, Plate, Swivel, Break
**000-BN5-0030
Condensing Unit
3234307
Catch, Door
2193927
Control, Pressure, Low
AE630AT-602-J7
Compressor
2183348
Cord, power, 16/3 W/Nema 5-15P
3526675
Condensing Unit, 1/3HP, Hi
*030-392-0000
Divider, Shelley IC Tank
2193927
Control, Pressure, Low
3234242
Drain, Plastic, 1IPS, 2.87
2183348
Cord, power, 16/3 W/Nema 5-15P
6690493
Drain, Valve, 3/4 NPT
3234242
Drain, Plastic, 1IPS, 2.87
†000-546-0030
Elevator Assembly, Small
6690493
Drain, Valve, 3/4 NPT
3234645
Leg, 6”, s/s
3516101
Drier, Filter, 1/4ODF
3234188
Lid
6700008
Gasket, Snap-In
*359-411-0003
Louver, 25 x 13
000-BOV-0031
Hinge, Pin Assembly, Right
*359-AZD-0001
Louver, Side, 13.00 X 13.50
000-BOV-0030
Hinge/Pin Assembly, Left
*359-AZD-0000
Louver, Side, 9.00 X 13.50
000-BOM-0033
Lid Assembly, Front, NDF-18
2190154
Switch, Rocker, 20A/125V
000-BOM-0031
Lid Assembly, Top, NDF-18
3516225
Valve, Expansion, Freezer, 1/4Ton
6230003
Lock, Key, Lid, NDF/NDFA
*359-AZD-0031
Panel, Access, NDF-18
SCF-48
3516059
Thermometer, Digital
372-395-0000
Carrier, Large Ice Cream
3516062
Valve, Expansion, R134A, RFG
**000-BN5-003G
Condensing Unit
2193927
Control, Pressure, Low
NSCF-48
2183348
Cord, power, 16/3 W/Nema 5-15P
372-395-0000
Carrier, Large Ice Cream
*030-392-0000
Divider, Shelley IC Tank
**000-BN5-0030
Condensing Unit
3234242
Drain, Plastic, 1IPS, 2.87
2193927
Control, Pressure, Low
6690493
Drain, Valve, 3/4 NPT
2183348
Cord, power, 16/3 W/Nema 5-15P
†000-546-0030
Elevator Assembly, Small
*030-392-0000
Divider, Shelley IC Tank
3234645
Leg, 6”, s/s
3234242
Drain, Plastic, 1IPS, 2.87
3234188
Lid
6690493
Drain, Valve, 3/4 NPT
*359-411-0003
Louver, 25 x 13
†000-546-0030
Elevator Assembly, Small
*359-AZD-0001
Louver, Side, 13.00 X 13.50
3234645
Leg, 6”, s/s
*359-AZD-0000
Louver, Side, 9.00 X 13.50
3234188
Lid
2190154
Switch, Rocker, 20A/125V
*359-411-0003
Louver, 25 x 13
3516225
Valve, Expansion, Freezer, 1/4Ton
*359-AZD-0001
Louver, Side, 13.00 X 13.50
*359-AZD-0000
Louver, Side, 9.00 X 13.50
2190154
Switch, Rocker, 20A/125V
3516273
Valve, Expansion, 1/4, Hi, R404a
3516225
Valve, Expansion, 1/4, Lo, R404a
*3516265
Valve, EPR, 3/8 ODF
* Part print on page 17.
** Condenser Assembly on page 15.
† Elevator Assembly on page 16.
For customer service, call (800) 733-8829, (800) 773-8821, Fax (989) 773-3210, www.delfield.com
13
Milk, Ice Cream & Milk & Ice Cream Dispensers Service and Installation Manual
Replacement Parts
MFSC-31, MFSC-44, MFSC-57, MFSC-2821
MF-2020
372-395-0000
Carrier, ice cream
372-395-0038
Carrier
AE540AT-238-J7
Compressor, Tecumsh
1701278
Cover, expansion valve
3526674
Condensing Unit, 1/4HP, Hi, R134A
*030-392-0000
Divider, Shelley IC Tank
2193927
Control, Pressure, Low
3234242
Drain, Plastic, 1IPS, 2.87
2183348
Cord, power, 16/3 W/Nema 5-15P
†000-546-0030
Elevator Assembly, Small
1701278
Cover, expansion valve
3234110
Handle, lid
*030-392-0000
Divider, Shelley IC Tank
000-BMN-0030
Lid assembly
3234242
Drain, Plastic, 1IPS, 2.87
3234021
Stopper, Drain, 1IPS
3516101
Drier, Filter, 1/4ODF
3516062
Valve, Expansion, R134A, RFG
†000-546-0030
Elevator Assembly, Small
3234188
Lid, Large, Ice Cream
*359-411-0003
Panel, Louvered, DropIn
3234021
Stopper, Drain, 1IPS
3516062
Valve, Expansion, R134A, RFG
MFSC-2020
372-395-0038
Carrier, ice cream
AE540AT-238-J7
Compressor, Tecumsh
3526674
Condensing Unit, 1/4HP, Hi, R134A
2193927
Control, Pressure, Low
2183348
Cord, power, 16/3 W/Nema 5-15P
1701278
Cover, expansion valve
3234242
Drain, Plastic, 1IPS, 2.87
3516101
Drier, Filter, 1/4ODF
†000-546-003E
Elevator Assembly, Large
3234110
Handle, lid
000-BMN-0030
Lid, Assembly
*359-411-0003
Panel, Louvered, DropIn
3234021
Stopper, Drain, 1IPS
3516062
Valve, Expansion, R134A, RFG
MF-2821, MF-31, MF-44, MF-57
6320007
Bearing, 0.50ID, 0.625OD
372-395-0000
Carrier
1701278
Cover, expansion valve
272-397-0030
Cover, top, elevator
*030-392-0000
Divider, Shelley IC Tank
3234242
Drain, Plastic, 1IPS, 2.87
†000-546-0030
Elevator Assembly, Small
* Part print on page 17.
** Condenser Assembly on page 15.
† Elevator Assembly on page 16.
14
For customer service, call (800) 733-8829, (800) 773-8821, Fax (989) 773-3210, www.delfield.com
Milk, Ice Cream & Milk & Ice Cream Dispensers Service and Installation Manual
Replacement Parts - Condensing Units
2
2
3
3
4
1
4
5
1
5
6
6
8
7
9
8
10
Condensing Unit
Condensing Unit
Key
Part Number
Description
Key
Part Number
Description
-
000-BN5-0030
Condensing Unit
-
000-BN5-003G
Condensing Unit
1
2160028
Fan, Axial, 5.5”, 120V
1
2160028
Fan, Axial, 5.5”, 120V
2
2160030
Guard, Fan, 6.0”
2
2160030
Guard, Fan, 6.0”
3
026-C58-0037
Shroud, condenser coil
3
026-C58-0037
Shroud, condenser coil
4
3526999
Compressor, Danfoss, NF5.5CLX,
115V/60Z
4
3527000
Compressor, Danfoss, NF7CLS,
115V/60HZ
5
3516438
Relay, overload, Danfoss, NF7CLX
2194788
Capacitor, start, 320MFD
5
7
2194787
Capacitor, start 280MFD
3516444
Relay, overload, Danfoss, NF5.5CLX
6
3516322
Drier, filter
6
3516324
High pressure cutout
7
075-231-0030
Pan, condensate
7
3516322
Drier, filter
8
3516454
Coil, Condenser
8
3516458
Receiver tank
8
075-231-0030
Pan, condensate
10
3516254
Coil, condenser
For customer service, call (800) 733-8829, (800) 773-8821, Fax (989) 773-3210, www.delfield.com
15
Milk, Ice Cream & Milk & Ice Cream Dispensers Service and Installation Manual
Replacement Parts - Elevator Assemblies
6
5
1
4
3
1
2
7
2
6
3
5
4
Elevator Assembly
Elevator Assembly
Key
Part Number
Description
-
000-546-003E
Elevator Assembly, Large
-
000-546-0035
Elevator assembly, 22.57” high
1
372-398-003e
Jacket elevator
1
272-397-0035
Cover, elevator
2
221-397-003e
Cover, top, elevator
2
044-393-0035
Rod, guide
4
6150201
Spring, Extension
3
6230024
Retainer
4
6150202
Spring, Extension
4
372-398-0035
Body, elevator
5
6230024
Retainer, Field Adj.
5
264-394-0000
Carrier bracket, elevator
6
044-393-0030
Rod, Guide, Elevator, 25.43”
6
6320007
Bearing
-
6320007
Bearing, 0.50”ID, 0.625”OD
7
264-396-0000
Carrier plate, elevator
-
264-394-0001
Elevator Carrier Plate
-
6150201
Spring
-
264-396-0001
Elevator Carrier Plate
Elevator Assembly
-
000-546-0030
Elevator assembly, 24.41” High
1
272-397-0030
Cover, elevator
2
044-393-0030
Rod, guide, 25.43”
3
6230024
Retainer
4
372-398-0030
Body, elevator
5
264-394-0000
Carrier bracket, elevator
6
6320007
Bearing
7
264-396-0000
Carrier plate, elevator
-
6150201
Spring
Elevator Assembly
-
000-546-0036
Elevator assembly, 12.6” High
1
272-397-0036
Cover, elevator
2
044-393-0036
Rod, guide, 13.62”
3
6230024
Retainer
4
372-398-0036
Body, elevator
5
264-394-0000
Carrier bracket, elevator
6
6320007
Bearing
7
264-396-0000
Carrier plate, elevator
-
6150201
Spring
16
For customer service, call (800) 733-8829, (800) 773-8821, Fax (989) 773-3210, www.delfield.com
Milk, Ice Cream & Milk & Ice Cream Dispensers Service and Installation Manual
Replacement Part Prints
3516265 - Valve, EPR, 3/8 ODF
000-BI7-0033 - Cover assembly, NLFAC8
000-BI7-0034 - Cover Assembly, Lift, NLFAC-12
000-BI7-0035 - Cover Assembly, Lift, NLFAC-16
359-AZD-0000 - Louver, 13.5” x 9”
359-AZD-0001 - Louver, 13.5” x 13”
359-411-000C - Louver, 25” x 13”, N-Series
359-411-0003 - Louver, 25” x 13”
030-392-0000 - Divider, Shelley IC Tank
030-392-0030 - Divider, Tray, MF, FF, RFF, SCF Series
265-774-0039 - Carrier, elevator, N520, N860, N1200, N1530
359-411-0041 - Louver, 13.00” X 25.00”
265-774-003A - Carrier, N6, N10, N14
359-AZD-0030 - Panel, Access, NDF-12
359-AZD-0031 - Panel, Access, NDF-18
377-AZ0-0004 - Bolt, Lock
271-BGF-0003 - Divider, Milk Crate, NLFAC
For customer service, call (800) 733-8829, (800) 773-8821, Fax (989) 773-3210, www.delfield.com
17
Milk, Ice Cream & Milk & Ice Cream Dispensers Service and Installation Manual
Standard Labor Guidelines To Repair Or Replace Parts On Delfield Equipment
Advice and recommendations given by Delfield Service Technicians do not constitute or guarantee any special coverage.
•
•
•
•
A maximum of 1-hour is allowed to diagnose a defective component.
A maximum of 1-hour is allowed for retrieval of parts not in stock.
A maximum travel distance of 100 miles round trip and 2-hours will be reimbursed.
Overtime, installation/start-up, normal control adjustments, general maintenance, glass breakage, freight damage, and/or
correcting and end-user installation error will not be reimbursed under warranty unless pre-approved with a Service Work
Authorization from Delfield. You must submit the number with the service claim.
Labor Of 1 Hour Is Allowed To Replace:
• Compressor Start Components and Overload Protector
• Condensate Element
• Defrost Timer
• Door Hinges, Locks, and Gaskets
• Evaporator/Condenser Fan Motor and Blade
• Fan Delay/Defrost Termination Switch
• Hi-limit/Thermal Protector Switch
• Springs/Lowerator
• Thermometer
• Thermostat
Labor Of 2 Hours To Replace:
• Defrost Element
• Locate/Repair Leak
• Pressure Control
Labor Of 3 Hours To Replace:
• Condenser or Evaporator Coil
• Expansion Valve
Labor Of 4 Hours To Replace:
• Compressor
This includes recovery of refrigerant and leak check.
$55.00 maximum reimbursement for refrigerant recovery (includes recovery machine, pump, torch, oil, flux, minor fittings,
solder, brazing rod, nitrogen, or similar fees.)
Refrigerants:
• R134A A maximum of $5.00/lb. or 31¢/oz. will be reimbursed.
• R404A A maximum of $15.00/lb. or $1.00/oz. will be reimbursed.
18
For customer service, call (800) 733-8829, (800) 773-8821, Fax (989) 773-3210, www.delfield.com
Milk, Ice Cream & Milk & Ice Cream Dispensers Service and Installation Manual
Notes
For customer service, call (800) 733-8829, (800) 773-8821, Fax (989) 773-3210, www.delfield.com
19
Covington, TN
Mt. Pleasant, MI
Thank you for choosing Delfield!
Help is a phone call away. Help our team of professional, courteous customer
service reps by having your model number and serial number available at the time
of your call (800) 733-8829.
Model:________________________ S/N: _______________________
Installation Date:________________
For a list of Delfield’s authorized parts depots,
visit our website at www.delfield.com
Register your Delfield warranty
online. Go to www.delfield.com
under the service tab to complete.
980 S. Isabella Rd., Mt. Pleasant, MI 48858, U.S.A. • (989) 773-7981 or (800) 733-8829 • Fax (989) 773-3210 • www.delfield.com
Delfield reserves the right to make changes in design or specifications without prior notice. ©2013 The Delfield Company. All rights reserved. Printed in the U.S.A.
DMMILKICE 05/13
9291482
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement