Extron electronics | RGB 302 | User`s guide | Extron electronics RGB 302 User`s guide

Extron electronics RGB 302 User`s guide
im Vertrieb von
CAMBOARD Electronics
User’s Guide
RGB 580xi
Universal Remote Interface
with Audio and ADSP™
www.extron.com
Extron Electronics, USA
1230 South Lewis Street
Anaheim, CA 92805
800.633.9876 714.491.1500
FAX 714.491.1517
Extron Electronics, Europe
Beeldschermweg 6C
3821 AH Amersfoort, The Netherlands
+800.3987.6673 +31.33.453.4040
FAX +31.33.453.4050
Extron Electronics, Asia
135 Joo Seng Rd. #04-01
PM Industrial Bldg., Singapore 368363
+800.7339.8766 +65.6383.4400
FAX +65.6383.4664
www.camboard.de
© 2006 Extron Electronics. All rights reserved.
Extron Electronics, Japan
Kyodo Building, 16 Ichibancho
Chiyoda-ku, Tokyo 102-0082
Japan
+81.3.3511.7655 FAX +81.3.3511.7656
Tel. 07131 911201
Fax 07131 911203
68-536-01 Rev. E
11 06
ce-info@camboard.de
im Vertrieb von
Precautions
Safety Instructions • English
This symbol is intended to alert the user of
important operating and maintenance (servicing)
instructions in the literature provided with the
equipment.
This symbol is intended to alert the user of the
presence of uninsulated dangerous voltage within
the product's enclosure that may present a risk of
electric shock.
Caution
Read Instructions • Read and understand all safety and operating
instructions before using the equipment.
Retain Instructions • The safety instructions should be kept for future
reference.
Follow Warnings • Follow all warnings and instructions marked on the
equipment or in the user information.
Consignes de Sécurité • Français
Ce symbole sert à avertir l’utilisateur que la
documentation fournie avec le matériel contient des
instructions importantes concernant l’exploitation
et la maintenance (réparation).
Ce symbole sert à avertir l’utilisateur de la présence
dans le boîtier de l’appareil de tensions
dangereuses non isolées posant des risques
d’électrocution.
Attention
Lire les instructions• Prendre connaissance de toutes les consignes de
sécurité et d’exploitation avant d’utiliser le matériel.
Conserver les instructions• Ranger les consignes de sécurité afin de
pouvoir les consulter à l’avenir.
Respecter les avertissements • Observer tous les avertissements et
consignes marqués sur le matériel ou présentés dans la documentation
utilisateur.
Sicherheitsanleitungen • Deutsch
Dieses Symbol soll dem Benutzer in der im
Lieferumfang enthaltenen Dokumentation
besonders wichtige Hinweise zur Bedienung und
Wartung (Instandhaltung) geben.
Dieses Symbol soll den Benutzer darauf
aufmerksam machen, daß im Inneren des
Gehäuses dieses Produktes gefährliche
Spannungen, die nicht isoliert sind und die einen
elektrischen Schock verursachen können,
herrschen.
Achtung
Lesen der Anleitungen • Bevor Sie das Gerät zum ersten Mal verwenden,
sollten Sie alle Sicherheits-und Bedienungsanleitungen genau
durchlesen und verstehen.
Aufbewahren der Anleitungen • Die Hinweise zur elektrischen Sicherheit
des Produktes sollten Sie aufbewahren, damit Sie im Bedarfsfall darauf
zurückgreifen können.
Befolgen der Warnhinweise • Befolgen Sie alle Warnhinweise und
Anleitungen auf dem Gerät oder in der Benutzerdokumentation.
Instrucciones de seguridad • Español
Este símbolo se utiliza para advertir al usuario
sobre instrucciones importantes de operación y
mantenimiento (o cambio de partes) que se desean
destacar en el contenido de la documentación
suministrada con los equipos.
Este símbolo se utiliza para advertir al usuario
sobre la presencia de elementos con voltaje
peligroso sin protección aislante, que puedan
encontrarse dentro de la caja o alojamiento del
producto, y que puedan representar riesgo de
electrocución.
Precaucion
Leer las instrucciones • Leer y analizar todas las instrucciones de
operación y seguridad, antes de usar el equipo.
Conservar las instrucciones • Conservar las instrucciones de seguridad
para futura consulta.
Obedecer las advertencias • Todas las advertencias e instrucciones
marcadas en el equipo o en la documentación del usuario, deben ser
obedecidas.
www.camboard.de
CAMBOARD Electronics
FCC Class A Notice
Avoid Attachments • Do not use tools or attachments that are not recommended by the
equipment manufacturer because they may be hazardous.
Warning
Power sources • This equipment should be operated only from the power source
indicated on the product. This equipment is intended to be used with a main
power system with a grounded (neutral) conductor. The third (grounding) pin is
a safety feature, do not attempt to bypass or disable it.
Power disconnection • To remove power from the equipment safely, remove all
power cords from the rear of the equipment, or the desktop power module (if
detachable), or from the power source receptacle (wall plug).
Power cord protection • Power cords should be routed so that they are not likely to
be stepped on or pinched by items placed upon or against them.
Servicing • Refer all servicing to qualified service personnel. There are no userserviceable parts inside. To prevent the risk of shock, do not attempt to service
this equipment yourself because opening or removing covers may expose you to
dangerous voltage or other hazards.
Slots and openings • If the equipment has slots or holes in the enclosure, these are
provided to prevent overheating of sensitive components inside. These openings
must never be blocked by other objects.
Lithium battery • There is a danger of explosion if battery is incorrectly replaced.
Replace it only with the same or equivalent type recommended by the
manufacturer. Dispose of used batteries according to the manufacturer's
instructions.
Note: This equipment has been tested and found to comply with the limits for a
Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed
to provide reasonable protection against harmful interference when the equipment is
operated in a commercial environment. This equipment generates, uses and can
radiate radio frequency energy and, if not installed and used in accordance with the
instruction manual, may cause harmful interference to radio communications.
Operation of this equipment in a residential area is likely to cause harmful
interference, in which case the user will be required to correct the interference at his
own expense.
Note: This unit was tested with shielded cables on the peripheral devices. Shielded
cables must be used with the unit to ensure compliance.
Eviter les pièces de fixation • Ne pas utiliser de pièces de fixation ni d’outils non
recommandés par le fabricant du matériel car cela risquerait de poser certains dangers.
Extron’s Warranty
Avertissement
Alimentations• Ne faire fonctionner ce matériel qu’avec la source d’alimentation indiquée
sur l’appareil. Ce matériel doit être utilisé avec une alimentation principale comportant
un fil de terre (neutre). Le troisième contact (de mise à la terre) constitue un dispositif de
sécurité : n’essayez pas de la contourner ni de la désactiver.
Déconnexion de l’alimentation• Pour mettre le matériel hors tension sans danger,
déconnectez tous les cordons d’alimentation de l’arrière de l’appareil ou du
module d’alimentation de bureau (s’il est amovible) ou encore de la prise secteur.
Protection du cordon d’alimentation • Acheminer les cordons d’alimentation de
manière à ce que personne ne risque de marcher dessus et à ce qu’ils ne soient
pas écrasés ou pincés par des objets.
Réparation-maintenance • Faire exécuter toutes les interventions de réparationmaintenance par un technicien qualifié. Aucun des éléments internes ne peut être
réparé par l’utilisateur. Afin d’éviter tout danger d’électrocution, l’utilisateur ne
doit pas essayer de procéder lui-même à ces opérations car l’ouverture ou le
retrait des couvercles risquent de l’exposer à de hautes tensions et autres dangers.
Fentes et orifices • Si le boîtier de l’appareil comporte des fentes ou des orifices,
ceux-ci servent à empêcher les composants internes sensibles de surchauffer. Ces
ouvertures ne doivent jamais être bloquées par des objets.
Lithium Batterie • Il a danger d'explosion s'll y a remplacment incorrect de la
batterie. Remplacer uniquement avec une batterie du meme type ou d'un ype
equivalent recommande par le constructeur. Mettre au reut les batteries usagees
conformement aux instructions du fabricant.
Keine Zusatzgeräte • Verwenden Sie keine Werkzeuge oder Zusatzgeräte, die nicht
ausdrücklich vom Hersteller empfohlen wurden, da diese eine Gefahrenquelle darstellen
können.
Extron Electronics warrants this product against defects in materials and
workmanship for a period of three years from the date of purchase. In the event of
malfunction during the warranty period attributable directly to faulty workmanship
and/or materials, Extron Electronics will, at its option, repair or replace said products
or components, to whatever extent it shall deem necessary to restore said product to
proper operating condition, provided that it is returned within the warranty period,
with proof of purchase and description of malfunction to:
USA, Canada, South America,
and Central America:
Extron Electronics
1001 East Ball Road
Anaheim, CA 92805, USA
Vorsicht
Stromquellen • Dieses Gerät sollte nur über die auf dem Produkt angegebene
Stromquelle betrieben werden. Dieses Gerät wurde für eine Verwendung mit
einer Hauptstromleitung mit einem geerdeten (neutralen) Leiter konzipiert. Der
dritte Kontakt ist für einen Erdanschluß, und stellt eine Sicherheitsfunktion dar.
Diese sollte nicht umgangen oder außer Betrieb gesetzt werden.
Stromunterbrechung • Um das Gerät auf sichere Weise vom Netz zu trennen,
sollten Sie alle Netzkabel aus der Rückseite des Gerätes, aus der externen
Stomversorgung (falls dies möglich ist) oder aus der Wandsteckdose ziehen.
Schutz des Netzkabels • Netzkabel sollten stets so verlegt werden, daß sie nicht
im Weg liegen und niemand darauf treten kann oder Objekte darauf- oder
unmittelbar dagegengestellt werden können.
Wartung • Alle Wartungsmaßnahmen sollten nur von qualifiziertem
Servicepersonal durchgeführt werden. Die internen Komponenten des Gerätes
sind wartungsfrei. Zur Vermeidung eines elektrischen Schocks versuchen Sie in
keinem Fall, dieses Gerät selbst öffnen, da beim Entfernen der Abdeckungen die
Gefahr eines elektrischen Schlags und/oder andere Gefahren bestehen.
Schlitze und Öffnungen • Wenn das Gerät Schlitze oder Löcher im Gehäuse
aufweist, dienen diese zur Vermeidung einer Überhitzung der empfindlichen
Teile im Inneren. Diese Öffnungen dürfen niemals von anderen Objekten
blockiert werden.
Litium-Batterie • Explosionsgefahr, falls die Batterie nicht richtig ersetzt wird.
Ersetzen Sie verbrauchte Batterien nur durch den gleichen oder einen
vergleichbaren Batterietyp, der auch vom Hersteller empfohlen wird. Entsorgen
Sie verbrauchte Batterien bitte gemäß den Herstelleranweisungen.
Evitar el uso de accesorios • No usar herramientas o accesorios que no sean
especificamente recomendados por el fabricante, ya que podrian implicar riesgos.
Advertencia
Alimentación eléctrica • Este equipo debe conectarse únicamente a la fuente/tipo de
alimentación eléctrica indicada en el mismo. La alimentación eléctrica de este equipo debe
provenir de un sistema de distribución general con conductor neutro a tierra. La tercera
pata (puesta a tierra) es una medida de seguridad, no puentearia ni eliminaria.
Desconexión de alimentación eléctrica • Para desconectar con seguridad la acometida
de alimentación eléctrica al equipo, desenchufar todos los cables de alimentación en el
panel trasero del equipo, o desenchufar el módulo de alimentación (si fuera
independiente), o desenchufar el cable del receptáculo de la pared.
Protección del cables de alimentación • Los cables de alimentación eléctrica se deben
instalar en lugares donde no sean pisados ni apretados por objetos que se puedan
apoyar sobre ellos.
Reparaciones/mantenimiento • Solicitar siempre los servicios técnicos de personal
calificado. En el interior no hay partes a las que el usuario deba acceder. Para
evitar riesgo de electrocución, no intentar personalmente la reparación/
mantenimiento de este equipo, ya que al abrir o extraer las tapas puede quedar
expuesto a voltajes peligrosos u otros riesgos.
Ranuras y aberturas • Si el equipo posee ranuras o orificios en su caja/alojamiento,
es para evitar el sobrecalientamiento de componentes internos sensibles. Estas
aberturas nunca se deben obstruir con otros objetos.
Batería de litio • Existe riesgo de explosión si esta batería se coloca en la posición
incorrecta. Cambiar esta batería únicamente con el mismo tipo (o su equivalente)
recomendado por el fabricante. Desachar las baterías usadas siguiendo las
instrucciones del fabricante.
Asia:
Extron Electronics, Asia
135 Joo Seng Road, #04-01
PM Industrial Bldg.
Singapore 368363
Europe, Africa, and the Middle East:
Extron Electronics, Europe
Beeldschermweg 6C
3821 AH Amersfoort
The Netherlands
Japan:
Extron Electronics, Japan
Kyodo Building
16 Ichibancho
Chiyoda-ku, Tokyo 102-0082
Japan
This Limited Warranty does not apply if the fault has been caused by misuse,
improper handling care, electrical or mechanical abuse, abnormal operating conditions
or non-Extron authorized modification to the product.
If it has been determined that the product is defective, please call Extron and ask for
an Applications Engineer at (714) 491-1500 (USA), 31.33.453.4040 (Europe),
65.6383.4400 (Asia), or 81.3.3511.7655 (Japan) to receive an RA# (Return
Authorization number). This will begin the repair process as quickly as possible.
Units must be returned insured, with shipping charges prepaid. If not insured,
you assume the risk of loss or damage during shipment. Returned units must
include the serial number and a description of the problem, as well as the name of
the person to contact in case there are any questions.
Extron Electronics makes no further warranties either expressed or implied with
respect to the product and its quality, performance, merchantability, or fitness for any
particular use. In no event will Extron Electronics be liable for direct, indirect, or
consequential damages resulting from any defect in this product even if Extron
Electronics has been advised of such damage.
Please note that laws vary from state to state and country to country, and that some
provisions of this warranty may not apply to you.
Tel. 07131 911201
Fax 07131 911203
ce-info@camboard.de
im Vertrieb von
CAMBOARD Electronics
䄺ਞ
ᅝܼ乏ⶹ•Ё᭛
䖭Ͼヺোᦤ⼎⫼᠋䆹䆒໛⫼᠋᠟‫ݠ‬Ё
᳝䞡㽕ⱘ᪡԰੠㓈ᡸ䇈ᯢDŽ
䖭Ͼヺো䄺ਞ⫼᠋䆹䆒໛ᴎ໇‫ݙ‬᳝
䴆ⱘॅ䰽⬉य़ˈ᳝㾺⬉ॅ䰽DŽ
⊼ᛣ
䯙䇏䇈ᯢк• 䑩ㅸỀ䑩嬦嫿⡈↎⼆枼敆嬼⶷䍇夤ㆁ㙊
⫊₩⏍Ề䑩嬵㕏ɿ
ֱᄬ䇈ᯢк• 䑩ㅸⷕ἞⪙⫊₩嬵㕏ᶧḦ⡈⭇㚦Ề䑩ɿ
䙉ᅜ䄺ਞ• 䑩ㅸⷕ徶⫉ᷨ␂⏍䑩ㅸ㉈⊘ᵋ䗅ㆁ㙊⫊₩
⏍㐎ẝ嬵㕏ɿ
䙓‫ܡ‬䗑ࡴ• ᵎ壂Ề䑩嬦ᷨ␂⋃⒇㯢㙊㋩劑䗅⴦₸ㅗ弾
⇡嫿⡈澤Ḧ忀₎⊲斪ɿ
www.camboard.de
Tel. 07131 911201
Fax 07131 911203
⬉⑤• 嬦嫿⡈⌫倾Ề䑩ᷨ␂ᵋ㝈㕏䗅䑶㷑ɿ嫿⡈⼆枼
Ề䑩㙊♱一䗅Ờ䑶䰼丠Ờ䑶ɿ䩭ᵊ㚢一澠♱一澡㕰
⫊₩嫿㓾澤ᵎ倾ᵎ䑩ㅗ崴弈ɿ
ᢨᥝ⬉⑤• ᵻ⫊₩♱ḏ嫿⡈㈕㋊䑶㷑澤嬸㈕㋊ㆁ㙊嫿
⡈⍏ㅗ㞍暣䑶㷑䗅䑶㷑一澤ㅗḼẖ㋦ⅱⵃ䑶䰼丠䗅
䑶㷑一ɿ
⬉⑤㒓ֱᡸ• ⣦Ⓟⵄ一澤忀₎埬嵪嵐澤ㅗ愎䆪㉥⋌ɿ
㓈ᡸ•ㆁ㙊丵Ἧ⼆枼䑲嫥嬂䗅丵Ἧ᷻⎙弜垍ɿ嫿⡈⃆
怩㯢㙊䑩ㅸ⌰Ḧ㘵㊣䗅昷ḷɿᵻ忀₎℻䋱大䑶⊲斪
ᵎ壂儫ⴲ嬖☿㆔⹁嫿⡈䘗⪑丵Ἧ嬦嫿⡈ɿ
䗮亢ᄨ• 㙊ᷜ嫿⡈㙻⠴ᵋ㙊彛栏㤾ㅗ⪕澤⫄ḭ㕰䑩㚦
敳㪣㙻⃆㒐だ₄ḷ弈䀮ɿᵎ壂䑩Ḽẖᵝ壀㉢Ẑ彛
栏⪕ɿ
䫖⬉∴• ᵎ㪤䞯䗅㘵㊣䑶㮡ṛ㙊䅇㿹䗅⊲斪ɿ⼆枼Ề䑩
ᵏ⋃⫷㋩劑䗅䘹⍍ㅗ䘹弒⛌⌸䗅䑶㮡ɿ㉊䂨䑠ᷨ⋃
䗅⸻嫯⡅䍇ⷠ⹄䑶㮡ɿ
ce-info@camboard.de
im Vertrieb von
CAMBOARD Electronics
Table of Contents
Chapter 1 • Introduction .......................................................... 1-1
About the RGB 580xi ............................................................ 1-2
Features ...................................................................................... 1-2
Chapter 2 • Installation and Setup .................................... 2-1
Installation Overview ......................................................... 2-2
Under-desk/-table/-podium mounting .................................. 2-3
Application Diagrams ......................................................... 2-4
Front Panel Features and Cabling ................................. 2-6
Rear Panel Features and Cabling .................................. 2-9
Front Panel Adjustments ................................................. 2-10
Mounting the Optional AAP Device .......................... 2-11
AAP Device Features ......................................................... 2-12
Cabling the AAP Device Rear Connectors ............... 2-13
Cable Cubby AAP Device Features ............................. 2-14
Cabling the Cable Cubby AAP Devices ..................... 2-15
Troubleshooting .................................................................... 2-17
Chapter 3 • Remote Control ................................................... 3-1
RS-232 Programmer’s Guide ............................................ 3-2
Host-to-interface communications ....................................... 3-2
Interface-initiated messages ................................................ 3-2
Error responses ...................................................................... 3-3
Using the command/response table ..................................... 3-3
Symbol definitions ................................................................. 3-4
Command/response table ..................................................... 3-4
Control Software for Windows® .................................... 3-5
Installing the software .......................................................... 3-5
Using the software ................................................................ 3-5
Contact Closure Remote Control .................................... 3-6
Appendix A • Specifications, Part Numbers, and
Accessories ........................................................................................ A-1
Specifications ......................................................................... A-2
Included Parts ......................................................................... A-5
Optional AAP Devices ........................................................ A-5
www.camboard.de
Tel. 07131 911201
Fax 07131 911203
ce-info@camboard.de
RGB 580xi • Table of Contents
iii
imContents,
Vertrieb von
Table of
cont’d
CAMBOARD Electronics
Optional Cable Cubby AAP Devices ............................ A-6
Optional RGB 580xi AAP Replacement Cables ...... A-6
RGB 580xi Remote Interface
Appendix B • Mounting Template ...................................... B-1
Dimensions ............................................................................... B-2
1
All trademarks mentioned in this manual are the properties of their respective
owners.
Chapter One
Introduction
About the RGB 580xi
Features
68-536-01 Rev. E
11 06
ii
iv
www.camboard.de
RGB
580xi • Table of Contents
Tel. 07131 911201
Fax 07131 911203
ce-info@camboard.de
im Vertrieb von
Introduction
CAMBOARD Electronics
About the RGB 580xi
RGB 580xi Remote Interface
The Extron RGB 580xi is an analog, remote-mountable
computer video interface that can be installed in a location that
is hidden from the user’s view. It features a 300 MHz (< -3 dB)
video bandwidth.
It accepts one analog computer video input (RGBHV, RGBS,
RGsB, and RsGsBs) on a 15-pin HD female connector and one
unbalanced stereo audio input on a 3.5 mm stereo female jack.
Five BNC female connectors provide video output (RGBHV,
RGBS, and RGsB), and a five-pole captive screw connector
provides for stereo audio output.
A variety of Architectural Adapter Plates (AAP) with A/V inputs
can be used in conjunction with the RGB 580xi and are ideal for
installation in remote locations, including discreet mounting in
the Extron Hideaway Surface Access Products, such as the
HSA 400, HSA 402 and HSA 822.
In addition, a series of RGB 580xi CC AAP plates are also
available for Extron Cable Cubby mounting.
In this manual, “RGB 580xi” and “remote interface” are used
interchangeably.
2
Chapter Two
Installation and Setup
Features
Stereo audio — Unbalanced, PC level stereo audio input can be
output as balanced or unbalanced stereo audio.
Installation Overview
Level and Peaking adjustments — Level and peaking controls
compensate for signal losses over long cable runs. Level
adjusts image brightness and peaking adjusts image
sharpness.
Application Diagrams
Front Panel Features and Cabling
Advanced Digital Sync Processing (ADSP™) — ADSP allows
sync processing operations, such as horizontal centering,
to occur without affecting the signal’s sync timing. This
allows horizontal centering to be applied to signals that
are output to digital display devices such as LCD
projectors, DLP projectors and plasma displays. A front
panel DIP switch provides another option, Digital Display
Sync Processing™ (DDSP™), to ensure proper displays
without altering sync pulse timing or width.
Rear Panel Features and Cabling
Front Panel Adjustments
Mounting the Optional AAP Device
AAP Device Features
Cabling the AAP Device Rear Connectors
Remote contact closure — A contact closure signal can be sent
to the interface from the remote AAP.
Cable Cubby AAP Device Features
RS-232 control — A set of instructions are available via the
Extron control software for Windows®, or any other
remote control system.
Cabling the Cable Cubby AAP Devices
Troubleshooting
1-2
www.camboard.de
RGB 580xi
xi • Introduction
Tel. 07131 911201
Fax 07131 911203
ce-info@camboard.de
im Vertrieb
Installation
andvon
Setup
CAMBOARD Electronics
Under-desk/-table/-podium mounting
Installation Overview
CAUTION
Installation and service must be performed by
authorized personnel only.
1.
Attach the under-desk mounting brackets
(part #70-077-01) to the interface with the six machine
screws (provided in the mounting kit), as shown below.
This procedure may also apply to table or podium
mounting applications. See “Application Diagrams” in this
chapter.
2.
Hold the interface with attached brackets against the
underside of the desk or other furniture. Mark the
location of holes for screws on the desk. See appendix B
for mounting dimensions.
3.
Drill 1/4" (6.4 mm) deep, 3/32" (2.38 mm) diameter pilot
holes in the table or desk at the marked screw locations
from the underside or inside (concealed side) of the
furniture, where the interface will be located.
4.
Insert the four wood screws into the pilot holes. Fasten
each screw into the installation surface until just less than
1/4" of the screw protrudes.
5.
Align the installed screws with the slots in the mounting
brackets, and place the interface against the surface, with
the screws through the bracket slots.
6.
Slide the interface slightly forward or back, then tighten all
four screws to fasten it in place.
To install and set up an RGB 580xi, follow these steps:
1
2
Turn all of the equipment off. Make sure that the
computer, the RGB 580xi, and the output devices
(projector/monitor, speakers) are all turned off and
disconnected from the power source.
For under-desk mounting:
A.
B.
Determine the installation location: table, desk,
podium, or other suitable location. If Architectural
Adapter Plates are to be connected to the interface,
consider where they will be located in relation to the
interface. See “Application Diagrams” in this
chapter.
Mount the interface. See “Under-desk/-table/
-podium mounting” in this chapter.
3
Attach output cables to the rear panel of the interface and
to the output devices. See “Rear Panel Features and
Cabling” in this chapter.
4
Attach input cables to the input devices and to the
interface’s front panel connectors. See “Front Panel
Features and Cabling” in this chapter.
5
Set the front panel DIP switches. Use the “Front Panel
Features and Cabling” section of this chapter as a guide.
6
Connect power cords and turn on the output devices
(projector/monitor, speakers), the remote interface, and
audio and video input devices.
7
The picture should appear, and sound should be audible.
If not, ensure that all devices are plugged in and receiving
power. Check the cabling and make adjustments as
needed.
8
While watching the display, adjust the video level and
peaking by using the rotary Level and Peaking controls.
See “Front Panel Adjustments” in this chapter.
AU
DIO
INPU
AN
TS
AL
OG
CO
NT
A
B
C
RO
D
L
E
VIDE
LE
O OU
L
TP
PE
VE
SO
SERG
DD R
SP
AKUT
ING
V-S
YN
NE C
WID
G
CO SYN TH
MP C
SYN
C
RG
B 58
0xi
Mounted under
a desk, table or
podium
Under-desk mounting of the RGB 580xi
2-2
www.camboard.de
RGB
580xi • Installation and Setup
Tel. 07131 911201
Fax 07131 911203
ce-info@camboard.de
RGB
580xi • Installation and Setup
2-3
im Vertrieb
von cont’d
Installation
and Setup,
CAMBOARD Electronics
Application Diagrams
The RGB 580xi can be hidden from view and remotely
connected to a computer through various Extron AAP and
Cable Cubby (CC) AAP devices that are installed in office
furniture or walls. Please consult with your Extron sales
representative concerning these AAP and CC AAP devices and
AAP-capable products from which devices may be installed.
RGB 580xi CCSI AAP
Audio
Sound System
754
APA
IER
AMPLIF
POWER
H
2
1
S INP
E U
L T
E
C
T
.S
H
IF
T
AUDIO
CH
CH
T
PROTEC
CLIP
NORM
RS-232
SIGNAL
PANEL
T
FRONT
LOCKOU
Projector
AUDIO
H. SHIFT
INPUT
SELECT
Projector
COMPUTER
RGB 580xi SI AAP
AUDIO
R
COMPUTE
INPUT
SELECT
SI
AAP
580xi
H.
SHIFT
RGB
102
AAP
AAP 102
Extron
RGB 580xi SI AAP
Mounted in the Extron AAP 102
To VGA
To
Audio
WIDTH
V-SYNC
SYNC
NEG SYNC
COMP
580xi
PEAKING
INPUT CT
SELE
RGB
LEVEL
RG
B 580
T
UT
INP EC
SEL
SOG
SERR
DDSP
OUTPUT
VIDEO
OL
E
xi
D
C
CONTR
B
INPUTS
G
A
CCI
AAP
ANALO
AUDIO
INPUTS
AUDIO
ANALOG
CONTROL
A B C D E
SOG
SERR
DDSP
V-SYNC WIDTH
NEG SYNC
COMP SYNC
VIDEO OUTPUT
LEVEL
Network
PEAKING
Extron
RGB 580xi
WIDTH
V-SYNC
SYNC
NEG SYNC
COMP
SOG
SERR
DDSP
UT
G
OUTP
PEAKIN
VIDEO
580
xi
RGB
LEVEL
TS
INPU
LOG
E
TROL
D
C
CON
B
A
ANA
IO
AUD
LAN/WAN
Network/
Internet
Remote Interface
Podium mounting of the RGB 580xi with an AAP
device
INPUTS
AUDIO
ANALOG
CONTROL
A B C D E
Projector
SOG
SERR
DDSP
V-SYNC WIDTH
NEG SYNC
COMP SYNC
VIDEO OUTPUT
LEVEL
PEAKING
RGB 580xi
RGB 580xi
HSA 400
RGB 580xi SI AAP
600W
Podium mounting of the RGB 580xi with a Cable
Cubby AAP device
MAX
H. SHIFT
PHONE
INPUT
SELECT
COMPU
DATA
AUDIO
TER
RGB
580
xi SI
AAP
HSA 400
Mounted
through a table
or podium
RGB 580xi
AUDIO
INPUT
ANALO S
Refer to the Cable Cubby User’s Manual
(part #68-701-01) for Cable Cubby installation
instructions.
G
CONTR
A
B
C
OL
D
E
VIDEO
LEVEL
SOG
SERR
OUTPUT
DDSP
PEAKING
V-SYNC
NEG
WIDTH
COMPSYNC
SYNC
RGB
580
xi
Mounted under
a table or
podium
Table mounting of the RGB 580xi with an AAP device
2-4
www.camboard.de
RGB
580xi • Installation and Setup
Tel. 07131 911201
Fax 07131 911203
ce-info@camboard.de
RGB
580xi • Installation and Setup
2-5
im Vertrieb
Installation
andvon
Setup
CAMBOARD Electronics
Front Panel Features and Cabling
4
INPUTS
AUDIO
ANALOG
CONTROL
A B C D E
SOG
SERR
DDSP
V-SYNC WIDTH
NEG SYNC
COMP SYNC
VIDEO OUTPUT
LEVEL
PEAKING
RGB 580xi
1
2
3
5
4
6
7
Contact closure control connector — Connect an optional
contact closure device to this female 5-pole captive screw
connector. Making contact closure between pins A and B
transmits a channel signal through the RS-232 port. Extron’s
RGB 580xi I AAP and RGB 580xi SI/CCSI AAP (see “AAP Device
Features” and “Cable Cubby AAP Device Features” in this
chapter) provide a one-button contact closure operation. Wire
the male connector as shown below on the left. Extron’s VGA
and control cable assembly (see chapter A, “Cables”, for part
numbers) comes with the male control connector prewired as
shown below on the right.
Prewired male control connector
Contact Closure
RGB 580xi front panel
Male VGA connector
Contact closure wiring
Audio input connector — Plug a 3.5 mm stereo plug into this
jack for unbalanced audio input. Wire the male plug as shown
below.
Tip (L)
Prewired male control
cable connector
5
Video output: level control — This control adjusts picture
brightness by compensating for signal amplitude loss caused by
cable resistance. See Front Panel Adjustments in this chapter.
6
Video output: peaking control — This control adjusts picture
sharpness by compensating for cable capacitance caused by long
cable runs. See Front Panel Adjustments in this chapter.
7
DIP switches — This bank of DIP switches, as illustrated below,
controls DDSP (Digital Display Sync Processing), serration pulse
output, SOG (sync on green) output, vertical sync width, sync
polarity, and composite sync output. Moving a switch up sets it
to On and moving it down sets it to Off.
Sleeve (GND)
Ring (R)
Tip (L)
Sleeve (GND)
Audio input wiring
3
RGB video input connector — Attach a cable
from the computer source to the RGB 580xi
via this 15-pin HD female connector. The
15-pin HD male connector pin locations and
pinout table are shown here.
6
1
5
11
15
A B C D E
2
Power/signal LED — This LED lights amber to indicate that the
RGB 580xi interface is receiving power, and lights green to
indicate it is receiving both power and an input signal.
CONTROL
1
Contact closure
Contact closure
5VDC
Ground
5VDC
10
SOG
SERR
DDSP
V-SYNC WIDTH
NEG SYNC
COMP SYNC
15-pin HD male pinout table
2-6
Pin
Description
Wire ID
1
2
3
4
5
6
7
8
9
red signal
green signal
blue signal
horizontal shift +
horizontal shift —
red coax ground
green coax ground
blue coax ground
LED red
red coax
green coax
blue coax
green wire
brown wire
red coax shield
green coax shield
blue coax shield
orange wire
Pin
Description
10 horizontal sync ground
10 vertical sync ground
10
audio ground
10
LED ground
10
shift ground
11
audio right
12
audio left
13
horizontal sync
14
vertical sync
15
LED green
www.camboard.de
RGB
580xi • Installation and Setup
Wire ID
black coax shield
yellow coax shield
black wire
yellow wire
gray wire
red wire
white wire
black coax
yellow coax
pink wire
The default for all DIP switches is Off (down).
Tel. 07131 911201
Fax 07131 911203
ce-info@camboard.de
RGB
580xi • Installation and Setup
2-7
im Vertrieb
von cont’d
Installation
and Setup,
CAMBOARD Electronics
1 — DDSP (Digital Display Sync Processing) — This feature
may be necessary for digital display devices such as LCD,
DLP (digital light processing) and plasma displays. Use this
option if the image is not displayed properly after other
options, such as serration pulse and vertical sync pulse
width, have been explored.
On —
Rear Panel Features and Cabling
100-240
0.5A MAX.
OUTPUTS
R
The interface uses DDSP instead of ADSP.
DDSP does not process the sync signal.
H
B
G
V
AUDIO
RS-232
Tx Rx
50/60 Hz
DDSP disables the horizontal shifting control.
1
Off — The interface performs sync processing operations,
such as centering, with ADSP.
2 — Serr (serration pulse) — Many LCD and DLP projectors
and plasma displays must have serration pulses removed
from the sync signal in order to display properly. Flagging
or bending at the top of the video image is a sign that the
serration pulses should be removed.
1
AC power connector — Connect a standard IEC AC power
cord here for power input (100 VAC to 240 VAC, 50/60 Hz) to
the internal, autoswitching power supply.
2
BNC output connectors — Connect coaxial cables from a
display device to these BNCs for one RGBHV, RGBS, or
RGsB/RsGsBs video output as follows:
On —
The interface outputs serration pulses in the vertical
sync interval.
Off — The interface does not output serration pulses.
R
3
H/HV
V
R
G
B
H/HV
RGBS
On —
RS-232 connector — Connect an RS-232 device (control system
or PC computer) to this female 3-pole captive screw connector
for two-way RS-232 communication. Software for RS-232
control is included with the interface. See the chapter three
section, Remote Control, for information on how to install and
use the control software and SIS commands. Wire the male
connector as shown below.
Tx Rx
Transmit
Receive
Ground
Tel. 07131 911201
Fax 07131 911203
Tip
Ring
Sleeve (s)
Tip
Ring
RS-232
The interface outputs combined horizontal and
vertical sync for RGBS.
Off — The interface outputs RGBHV or RGsB video.
V
R
6 — Comp Sync — This switch controls composite sync output.
H/HV
Balanced Output
R
See Caution
4
B
L
See Caution
Both the horizontal and the vertical sync signals are
forced to negative polarity on output.
Off — Output sync polarity follows (is the same as) input
polarity.
G
Connect the sleeve to ground (GND). Connecting
the sleeve to a negative (-) terminal will damage the
audio output circuits.
L
Tip
On —
R
Audio output connector — Cable an audio device to the
interface via this female 5-pole captive screw connector. Wire
the male connector as shown below.
Sleeve (s)
Tip
5 — Neg Sync — This switch controls sync polarity.
V
RGsB (Sync on Green)
RsGsBs (output only if input is RsGsBs)
Unbalanced Output
On — The vertical sync pulse is narrow.
Off — The vertical sync pulse is wide.
www.camboard.de
RGB
580xi • Installation and Setup
B
CAUTION
4 — V-Sync Width (vertical sync pulse width) — For some
digital display devices, if no picture appears, the picture
cuts in and out, or the picture is scrambled, try adjusting
the output vertical sync pulse width or switching from
ADSP to DDSP.
2-8
G
RGBHV
3 — SOG (sync on green)
On — The interface outputs sync on green.
Off — The interface outputs separate horizontal and
vertical sync (on the H and V connectors) for
RGBHV.
4
3
2
ce-info@camboard.de
RGB
580xi • Installation and Setup
2-9
im Vertrieb
von cont’d
Installation
and Setup,
CAMBOARD Electronics
Front Panel Adjustments
Video signals passing through long cable runs (over 125 feet)
can decrease in strength, creating signal loss. The longer the
cable, the greater the cable resistance and capacitance, and the
greater the level and peaking adjustments that will be required
to compensate for the resultant signal loss. These adjustments
change the level and peaking of the output signal to compensate
for capacitance caused by up to 1000 feet (304.8 meters) of
Extron SHR cable.
If the displayed image is too bright or too dark, try
changing the level setting. If the edges of the displayed
image seem to exceed their boundaries, or if thin lines
and sharp edges look thick and fuzzy, try changing the
peaking setting. See the illustration below.
TS
INPU
G
ALO
AN
OL
E
NTRD
COB C
VE
LE
A
B
RG
58
Peaking control — The Video Output Peaking control
affects the sharpness of a picture. Increased peaking can
compensate for detail (mid- and high-frequency) loss from
low bandwidth system components or capacitance in long
cables. The minimum setting (at the counterclockwise
limit) provides no peaking. The maximum setting (at the
clockwise limit) provides 100% peaking. Adjust this
control while viewing the displayed image to obtain the
optimum picture sharpness.
Extron’s various RGB 580xi AAP double-space devices may be
mounted to any Extron product that has an AAP faceplate, or to
an Extron AAP wallplate. See appendix A for AAP device part
numbers. The AAP device should be cabled before it is attached
to a faceplate or wallplate (see “Cabling the AAP Device Rear
Connectors” in this chapter). The screws needed for installing
an AAP device are built into its front panel, so no additional
screws are needed.
0xi
Peaking
DIO
AU
1.
Level
1.
2.
Mounting the Optional AAP Device
TH
WID
C
YN NC
V-S SY NC
G SY
NE
MP
CO
G
SO
RR
SE
SP
DD
UT
TPING
AK
O OU
PE
VIDE L
passes through long cables. Set the level at the maximum
setting for cable lengths over 500 feet for all computer
signals of 15 kHz to 135 kHz.
Level adjustment control — The Video Output Level
control alters the brightness of the displayed image. To
adjust the video output level, view the display while using
a small, flat-blade screwdriver to rotate this one-turn
potentiometer. You can judge the adjustment visually by
looking at the display.
Insert the AAP’s screws through the holes in the AAP
faceplate or the AAP wallplate. Secure the AAP device to
the faceplate or wallplate with the provided captive
washers and #4-40 nuts.
If the interface receives a typical (0.7 volts p-p) analog
computer video input, the output is as follows:
•
At the minimum level setting (the counterclockwise
limit of this control), the interface outputs video at
0.5 volts p-p.
•
Unity level is 0.7 volts p-p, the same as the input
signal. Set the control to approximately one-half turn
between the minimum and maximum level settings
to output unity level video.
Cable
Clamp
AAP 102
Cable
2
P 10
AA
DIO
AU
TE
MPU
CO
T
INPUCT
LE
SE
•
At the maximum level setting (the clockwise limit of
this control), the interface outputs video at
1.45 volts p-p.
www.camboard.de
RGB
580xi • Installation and Setup
58
P
AA
0x
RGB 580xi SI AAP
#4-40 Nut w/ Captive
Washer
Select a level setting of 0.7 volts or above to compensate
for the decrease in signal level that occurs when the signal
2-10
R
i SI
B
RG
IFT
H SH
Example of mounting an AAP device to a wallplate
Tel. 07131 911201
Fax 07131 911203
ce-info@camboard.de
RGB
580xi • Installation and Setup
2-11
im Vertrieb
von cont’d
Installation
and Setup,
2.
Follow steps 3 through
section of this chapter.
CAMBOARD Electronics
in the Installation Overview
8
DDSP disables the horizontal shifting control.
5
AAP Device Features
3
4
3
AUDIO IN
SHIFT
AUDIO IN
RGB 580xi AAP
RGB 580xi S AAP
RGB 580xi
1
Cabling the AAP Device Rear Connectors
Extron’s various AAP devices for the RGB 580xi may come with
several rear connectors that may require cabling.
COMPUTER IN
COMPUTER IN
2
Input select button — Pressing this button results in contact
closure between pins A and B of the contact closure control
connector on the front panel of the RGB 580xi.
RGB 580xi
1
Although the VGA and control cable/LED assembly
comes prewired to the captive screw connectors, any
subsequent cable assembly replacement will require the
following cabling instructions.
2
3
4
RGB 580xi SI AAP
SELECT
SHIFT
AUDIO IN
To cable the captive screw connectors, refer to the following
diagrams and orient the wires according to the view angle of
the captive screws. When using Extron’s VGA and control cable
assembly (see appendix A, “Optional RGB 580xi AAP Extension
Cables” for part numbers), refer to the color of each wire for
signal identification.
COMPUTER IN
RGB 580xi
1
1
5
2
Power/signal LED — This LED lights
•
•
amber to indicate that the AAP device is receiving power.
AUDIO
green to indicate that an active sync signal is present at the
input and that the AAP device is receiving power.
H. SHIFT
The LED flashes green whenever the minimum and
maximum limits of the horizontal shift control (H. shift)
have been reached.
2
RGB video input connector — Attach a cable from the
computer source to this 15-pin HD female connector.
3
Audio input connector — Plug a 3.5 mm stereo plug into this
jack for unbalanced audio input. Wire the male plug as shown
below.
Tip (L)
INPUT
SELECT
COMPUTER
RGB 580xi SI AAP
3
Sleeve (GND)
Red
Black
White
Yellow
Pink
Lt. Blue
Green Purple
Gray
1
2
Ring (R)
Tip (L)
Example of AAP device rear connectors
Sleeve (GND)
4
2-12
Horizontal shift control knob (H. shift) — While viewing the
displayed image, rotate this control to move the image to the
right or left on the screen. The power/signal LED flashes green
whenever the minimum and maximum limits of this control are
reached.
www.camboard.de
RGB
580xi • Installation and Setup
Tel. 07131 911201
Fax 07131 911203
1
Control connector (J4) — Insert wires into and tighten the
screws on the 3.5 mm, 5-pole captive screw connector. This
connector is used for contact closure and horizontal shifting
signals. Wire the connector as shown in the following
illustration.
ce-info@camboard.de
RGB
580xi • Installation and Setup
2-13
im Vertrieb
von cont’d
Installation
and Setup,
CAMBOARD Electronics
LED connector (J2) — Insert wires into and tighten the screws
on the 3.5 mm, 3-pole captive screw connector. This connector
is used for powering the green and amber LEDs. Wire the
connector as shown in the following illustration.
H
CC AAP Audio connector
Audio output connector (J3) — Insert wires into and tighten the
screws on the 3.5 mm, 3-pole captive screw connector. This
connector is used for unbalanced stereo audio output. Wire the
connector as shown in the following illustration.
Cable Cubby
1
L+
R+
3 2 1
1
•
RGB 580xi
RGB 580xi CCS AAP
SHIFT
2
INPUT
SELECT
3
2
Horizontal shift control knob (H. shift) — While viewing the
displayed image, rotate this control to move the image to the
right or left on the screen. The power/signal LED flashes green
whenever the minimum and maximum limits of this control are
reached.
DDSP disables the horizontal shifting control.
3
Input select button — Pressing this button results in contact
closure between pins A and B of the contact closure control
connector on the front panel of the RGB 580xi.
Cabling the Cable Cubby AAP Devices
RGB 580xi
Extron’s various CC AAP devices for the RGB 580xi come with
rear panel connectors that may require cabling.
RGB 580xi CCSI AAP
Although the control cable/LED cable assembly comes
prewired to the captive screw connectors, any
subsequent connector replacement will require the
following cabling instructions.
Installation of the RGB 580xi CC AAP devices in a Cable Cubby
allows the VGA and audio cable connectors of the CC AAP
device to be accessible, as shown in the following diagram.
2-14
www.camboard.de
RGB
580xi • Installation and Setup
amber to indicate that the CC AAP device is receiving
power.
green to indicate that an active sync signal is present at the
input and that the CC AAP device is receiving power.
The LED flashes green whenever the minimum and
maximum limits of the horizontal shift control (H. shift)
have been reached.
1
2
Power/signal LED — This LED lights
•
Audio left (white)
Audio ground (black)
Audio right (red)
Cable Cubby AAP Device Features
SHIFT
S INP
E U
L T
E
C
T
.S
H
IF
T
CC AAP VGA connector
LED
1 2 3
Green LED (pink)
LED ground (yellow)
Amber LED (orange)
3
RGB 580xi CCSI AAP
Control
2
1 2 3 4 5
Horizontal shift + (green)
Horizontal shift ground (gray)
Horizontal shift – (brown)
Contact closure + (light blue)
Contact closure – (purple)
Tel. 07131 911201
Fax 07131 911203
ce-info@camboard.de
RGB
580xi • Installation and Setup
2-15
im Vertrieb
von cont’d
Installation
and Setup,
CAMBOARD Electronics
To cable the captive screw connectors, refer to the following
diagrams and orient the wires according to the view angle of
the captive screws.
Troubleshooting
Turn on the input devices (computer, audio device) and output
device(s) (projector, monitors, speakers). The image should
now appear on the screen, and sound should be audible.
J2
If the image does not appear or there is no sound
2
J4
SHIFT
1.
Ensure that all devices are plugged in.
2.
Make sure that each device is receiving power. The
interface’s front panel LED lights green if the interface is
receiving power.
3.
Check the cabling and the audio connector wiring and
grounding, and make adjustments as needed.
4.
For digital display devices (including LCD, DLP and
plasma devices), try turning DDSP on or off using the
front panel DIP switch.
5.
To test the system setup and output, substitute a video test
generator for the computer input. Unplug the power
cords of the input/output devices and the remote
interface, replace the video source with a VTG, then
reconnect the power cords to restore AC power.
6.
Call Extron’s S3 Sales & Technical Support Hotline if
needed.
1
INPUT
SELECT
RGB 580xi
RGB 580xi CCSI AAP
1
Control connector (J4) — Insert wires into and tighten the
screws on the 3.5 mm, 5-pole captive screw connector. This
connector is used for contact closure and horizontal shifting
signals. Wire the connector as shown in the following
illustration.
LED connector (J2) — Insert wires into and tighten the screws
on the 3.5 mm, 3-pole captive screw connector. This connector
is used for powering the green and amber LEDs. Wire the
connector as shown in the following illustration.
The VGA and audio cable assemblies are routed through
the Cable Cubby. Refer to the Cable Cubby User’s
Manual (part #68-701-01) for Cable Cubby installation
instructions.
2-16
www.camboard.de
RGB
580xi • Installation and Setup
If the output image looks too green, the sync on green
(SOG) DIP switch may be set to On, and the display device
may not be configured to handle SOG signals. Set SOG to
Off.
2.
If the picture bends or flags at the top of the screen, set the
serration pulse DIP switch to Off.
3.
For a display device that experiences intermittent glitches,
try turning DDSP on or off using the front panel DIP
switch.
4.
If the picture “hangs off” the left or right edge of the
screen, and an RGB 580xi S AAP, RGB 580xi CCS AAP, RGB
580xi SI AAP, or RGB 580xi CCSI AAP device is connected
to the interface, adjust the AAP’s horizontal shift (H. Shift)
control to center the image.
5.
If the edges of the image seem to exceed their boundaries
or if thin lines and sharp edges look thick and fuzzy, try
changing the Peaking control setting. If the image is too
bright or dark, try changing the Level control setting.
LED
1 2 3
Green LED (pink)
LED ground (yellow)
Amber LED (orange)
1.
Control
2
1 2 3 4 5
Horizontal shift + (green)
Horizontal shift ground (gray)
Horizontal shift – (brown)
Contact closure + (light blue)
Contact closure – (purple)
If the image is not displayed correctly
Tel. 07131 911201
Fax 07131 911203
ce-info@camboard.de
RGB
580xi • Installation and Setup
2-17
im Vertrieb
von cont’d
Installation
and Setup,
6.
CAMBOARD Electronics
If the image still does not display correctly, call Extron’s S3
Sales & Technical Support Hotline.
RGB 580xi Remote Interface
3
Chapter Three
Remote Control
RS-232 Programmer’s Guide
Control Software for Windows®
Contact Closure Remote Control
2-18
www.camboard.de
RGB
580xi • Installation and Setup
Tel. 07131 911201
Fax 07131 911203
ce-info@camboard.de
im Vertrieb
Remote
Controlvon
CAMBOARD Electronics
There are two ways to control the horizontal shifting feature of
an RGB 580xi remote interface: by using the AAP horizontal
shift (H. shift) control, or by using an RS-232 remote control
device.
RECONFIG
When the remote interface’s RGB video input is disconnected or
the horizontal shift control (H. shift) is adjusted from the AAP
device (RGB 580xi S/CCS AAP and RGB 580xi SI/CCSI AAP),
the interface sends the reconfiguration message. No response is
required from the RS-232 host, but the host may request a new
status listing via the request information command (I/i). See
the command/response table in this chapter for details.
RS-232 Programmer’s Guide
The interface can be remotely controlled via a host computer
attached to the rear panel’s 3-pole captive screw RS-232
connector. A contact closure control system may also be used
by connecting a contact closure device to the front panel’s
female 5-pole captive screw connector. The protocol is 9600
baud, 1 stop bit, no parity, and no flow control.
The RS-232 control device (host) can use
either Extron’s Simple Instruction Set
(SIS™) commands or the graphical control
program for Windows. RS-232 control
software is included with the interface.
Chn
A contact closure selection has been detected from the remote
AAP contact closure switch (RGB 580xi I AAP and
RGB 580xi SI/CCSI AAP).
RS-232
Error responses
Tx Rx
Captive Screw Pin Locations
Female
The rear panel’s RS-232 3-pole female
connector has the following pin assignments:
Pin
RS-232 function
Description
1
2
3
Tx
Rx
Gnd
Transmit data
Receive data
Signal ground
When the interface receives a valid SIS command, it executes the
command and sends a response to the host device. If the
interface is unable to execute the command because the
command is invalid or it contains invalid parameters, it returns
an error response to the host.
The error response codes and their descriptions are as follows:
E10 – Invalid command
E13 – Invalid value (the number is out of range)
Using the command/response table
The command/response table lists valid command ASCII codes,
the interface’s responses to the host, and a description of the
command’s function or the results of executing the command.
Lowercase characters are acceptable in the command field only
where indicated. The ASCII to HEX conversion table below is
for use with the command/response table.
Host-to-interface communications
SIS commands consist of one or more characters per field. No
special characters are required to begin or end a command
sequence. When a command is valid, the interface executes the
command and sends a response to the host device. All
responses from the interface to the host end with a carriage
return and a line feed (CR/LF = ), which signals the end of
the response character string. A string is one or more
characters.
ASCII to HEX Conversion Table
•
Interface-initiated messages
When a local event such as a front panel or contact closure
selection or adjustment takes place, the interface sends a
message to the host. No response is required from the host.
The interface-initiated messages are listed here (underlined).
(C) Copyright 2001, Extron Electronics, RGB 580xi, Vx.xx
The interface displays the copyright message when it first
powers on. Vx.xx is the firmware version number.
3-2
www.camboard.de
RGB 580xi • Remote Control
Tel. 07131 911201
Fax 07131 911203
ce-info@camboard.de
RGB 580xi • Remote Control
3-3
3-4
www.camboard.de
RGB
580xi • Remote Control
Display version (Ver x.xx)
Display interface’s part #
Display status
Control Software for Windows
X2
Installing the software
The control program is contained on a 3.5-inch diskette, and it
can run from the floppy drive. However, it is more convenient
to run the program from the hard drive.
To install the software onto the hard drive, run SETUP.EXE from
the floppy disk, and follow the instructions that appear on the
screen. The program requires approximately 1 MB (megabyte)
of hard disk space.
By default the installation creates a C:\RGB302 directory, and it
places two icons (RGB 302+304 Control Pgm and RGB 302+
304 Help) into a group or folder named “Extron Electronics”.
Using the software
Q/q
N/n
I/i
To run the control program, follow these steps:
1.
Double-click on the RGB 302 + 304 Control Pgm icon in the
Extron Electronics group or folder, or on
the Rgb302.exe icon in the C:\RGB302
directory. The Comm menu appears on
the screen.
2.
Click on the comm port that is connected to the interface’s
RS-232 port. The control software “looks for” the interface
at that port and reads its configuration.
The control program window (shown below) appears and
displays current settings.
Query firmware version number
Request part number
Request information
Firmware version, part number & information requests, and reset
The included graphical control software for Windows offers
another way to control the interface via RS-232 in addition to
the Simple Instruction Set commands listed on page 3-4. The
control software is compatible with Windows 3.1x, Windows 95/
98, and Windows NT. The RGB 580xi uses version 2.0 or higher
of Extron’s RGB 302/304 Control Program, which is included
with these interfaces.
N_60-362-01
(see below)
Hph X1 •Hrt X3 •Vrt X3
X1
X1
Specify horizontal shift
Shift right one step
Shift left one step
Horizontal shift
X1
H
{H
}H
Hph
Hph
Hph
Chn
X1
Set horizontal shift value
Increment up
Increment down
Contact closure has been
detected across pins 1 and 2.
CAMBOARD Electronics
Whenever the Input Select button on the AAP device is pressed,
contact closure is initiated at the RGB 580xi remote interface and
a signal is sent from the remote interface’s RS-232 port.
Command description
Command/response table
X3
ASCII Command
(host to interface)
Response
(interface to host)
Additional
description
= Shift control range (-63 to +63)
= Controller firmware version (listed to two decimal places
e.g.: x.xx)
= Frequency in Hz or kHz (listed as xxx.xx)
X2
X1
= CR/LF
(carriage return/line feed) (hex 0D 0A)
= Space
•
Symbol definitions
The command/response table page uses symbols (defined below) to represent variables.
Vertriebcont’d
von
RemoteimControl,
Tel. 07131 911201
Fax 07131 911203
ce-info@camboard.de
RGB 580xi • Remote Control
3-5
Vertriebcont’d
von
RemoteimControl,
CAMBOARD Electronics
For information on program features, press the F1 computer
key, click on the Help menu from within the
control program, or double-click on the
RGB 302+304 Help icon in the Extron Electronics
group or folder.
RGB 580xi Remote Interface
Contact Closure Remote Control
For contact closure, connect a contact closure remote control
device to the front panel’s contact closure female 5-pole captive
screw connector. Various AAP devices and cable assemblies are
also available from Extron to provide remote contact closure
capability. The pin assignments for the RGB 580xi’s contact
closure connector are shown in the following table.
Pin
Contact closure
Description
A
B
C
D
E
Contact closure +
Contact closure +5V
Gnd
-5V
Contact closure + circuit
Contact closure - circuit
+5V source for powering AAP devices
Signal ground for powering AAP devices
-5V source for powering AAP devices
A
Appendix
Specifications, Part Numbers,
and Accessories
Specifications
Included Parts
Optional AAP Devices
Optional Cable Cubby AAP Devices
Optional RGB 580xi AAP Extension Cables
3-6
www.camboard.de
RGB
580xi • Remote Control
Tel. 07131 911201
Fax 07131 911203
ce-info@camboard.de
im Vertrieb Parts,
von
Specifications,
and Accessories
CAMBOARD Electronics
Specifications
Output level ..................................
Input impedance ..........................
Output impedance .......................
Max. propagation delay ..............
Max. rise/fall time .......................
Polarity ..........................................
Video — RGB 580xi
Gain ................................................ 0.35 V to 1.45 Vp-p
Bandwidth ..................................... 300 MHz (-3 dB)
Video input — RGB 580xi
Number/signal type ...................
Connectors ...................................
Nominal level ...............................
Minimum/maximum levels .......
Impedance ....................................
Horizontal frequency ..................
Vertical frequency .......................
Return loss ....................................
DC offset (max. allowable) .........
1 analog RGBHV, RGBS, RGsB, RsGsBs
1 female 15-pin HD
0.7 Vp-p for RGB
Analog: 0.3 V to 1.45 Vp-p with no offset
75 ohms or high Z, switchable (set to
75 ohms if no local monitor is connected)
Autoscan 15 kHz to 150 kHz
Autoscan 40 Hz to 140 Hz
<-30 dB @ 5 MHz
2.0 V
Audio
Gain ................................................ Unbalanced output: 0 dB; balanced output:
+6 dB
Frequency response .................... 20 Hz to 20 kHz, ±0.05 dB
THD + Noise ................................. 0.03% @ 1 kHz, 0.3% @ 20 kHz at nominal
level
S/N ................................................ >90 dB at maximum output, balanced
(unweighted)
Stereo channel separation .......... >90 dB @ 1 kHz to 20 kHz
Video input — RGB 580xi AAP, RGB 580xi I AAP, RGB
580xi S AAP, RGB 580xi SI AAP
Number/signal type ................... 1 analog RGBHV, RGBS, RGsB, RsGsBs
Connectors ................................... 1 female 15-pin HD
Audio input
Number/signal type ................... 1 PC level stereo, unbalanced
Connectors ................................... (1) 3.5 mm stereo mini audio jack (female)
(tip, ring, sleeve)
Impedance .................................... >5k ohms, unbalanced, DC coupled
Nominal level ............................... -10 dBV (316 mV)
Maximum level ............................ +8.5 dBu, (balanced or unbalanced) at 1%
THD+N
Video output — RGB 580xi
Number/signal type ...................
Connectors ...................................
Nominal level ...............................
Minimum/maximum levels .......
Impedance ....................................
Return loss ....................................
DC offset .......................................
1 analog RGBHV, RGBS, RGsB
5 BNC female
0.7 Vp-p for RGB
0.35 V to 1.45 Vp-p
75 ohms
-30 dB @ 5 MHz
±5 mV maximum with input at 0 offset
0 dBu = 0.775 Vrms, 0 dBV = 1 Vrms, 0 dBV
Video output — RGB 580xi AAP, RGB 580xi I AAP, RGB
580xi S AAP, RGB 580xi SI AAP
Sync
Input type ..................................... RGBHV, RGBS, RGsB, RsGsBs
Output type .................................. RGBHV, RGBS, RGsB
Input level ..................................... 2 V to 5.5 Vp-p with ±0.2 VDC offset max.
www.camboard.de
RGB
580xi • Specifications, Parts, and Accessories
2 dBu
Audio output
Number/signal type ................... 1 analog RGBHV, RGBS, RGsB
Connectors ................................... 1 female 15-pin HD
A-2
TTL: 4 V to 5 Vp-p, unterminated
510k ohms
75 ohms
85 ns
2 ns
RGBHV: Polarity follows input when
RGBHV is input and the sync polarity
switch is set to Off. Sync polarity is
negative if the sync polarity switch is set to
On.
RGBS, RGsB: negative
Tel. 07131 911201
Fax 07131 911203
Number/signal type ................... 1 buffered stereo (2 channel), balanced/
unbalanced
Connectors ................................... (1) 3.5 mm, captive screw connector, 5
pole
Impedance .................................... 50 ohms unbalanced, 100 ohms balanced
Gain error ..................................... ±0.1 dB channel to channel
Maximum level (600 ohm) ......... > +14 dBm, balanced or unbalanced at 1%
THD+N
ce-info@camboard.de
RGB 580xi • Specifications,
Parts, and Accessories
A-3
im Vertrieb
von and Accessories, cont’d
Specifications,
Parts,
CAMBOARD Electronics
Control/remote — interface
Serial control port ........................
Baud rate and protocol ...............
Serial control pin configuration ...
Program control ..........................
RS-232, captive screw connector, 3 pole
9600 baud, 8 data bits, 1 stop bit, no parity
1 = TX, 2 = RX, 3 = GND
Extron’s control/configuration program
for Windows®
Extron’s Simple Instruction Set (SIS™)
Power (RGB 580xi) ....................... 100 VAC to 240 VAC, 50/60 Hz, 18 watts,
internal, autoswitchable
Temperature/humidity .............. Storage: -40 to +158 °F (-40 to +70 °C) /
10% to 90%, noncondensing
Operating: +32 to +122 °F (0 to +50 °C) /
10% to 90%, noncondensing
Rack mount .................................. No, but furniture mountable with included
under-desk mounting kit #70-077-01
Enclosure type .............................. Metal (vented)
Enclosure dimensions
RGB 580xi .......................... 1.75" H x 6.4" W x 6.0" D
4.4 cm H x 16.3 cm W x 15.2 cm D
(Depth excludes connectors.)
RGB 580xi AAP models
Faceplate ................... 1.4" H x 3.5" W x 0.1" D
(3.6 cm H x 8.9 cm W x 0.3 cm D)
(double-space high AAP plates)
Circuit board ............ 1.3" H x 2.5" W x 0.9" D
(3.3 cm H x 6.4 cm W x 2.3 cm D)
(Depth excludes connectors, knobs, and
faceplate.)
Product weight
RGB 580xi I AAP 3', RGB 580xi SI AAP 3' ............. 0.4 lbs (0.2 kg)
RGB 580xi AAP 3', RGB 580xi S AAP 3' ................. 0.5 lbs (0.3 kg)
RGB 580xi AAP 6', RGB 580xi I AAP 6' .................. 0.6 lbs (0.3 kg)
RGB 580xi S AAP 6', RGB 580xi SI AAP 6' ............. 0.7 lbs (0.3 kg)
RGB 580xi AAP 12', RGB 580xi I AAP 12',
RGB 580xi S AAP 12', RGB 580xi SI AAP 12' ......... 1.0 lbs (0.5 kg)
RGB 580xi .................................................................. 1.2 lbs (0.5 kg)
Shipping weight ........................... AAP models .............. 2 lb (1 kg)
RGB 580xi .................. 4 lbs (2 kg)
Vibration ....................................... ISTA 1A in carton (International Safe
Transit Association)
Listings .......................................... UL, CUL
www.camboard.de
RGB
580xi • Specifications, Parts, Accessories
All nominal levels are at ±10%.
Specifications are subject to change without notice.
Included Parts
General
A-4
Compliances ................................. CE, FCC Class A, VCCI, AS/NZS, ICES
MTBF ............................................. 30,000 hours
Warranty ....................................... 3 years parts and labor
Tel. 07131 911201
Fax 07131 911203
These items are included in each order for an RGB 580xi:
Included parts
Part number
RGB 580xi
60-362-01
3.5 mm, 5-pole captive screw connectors (2)
10-319-10
3.5 mm, 3-pole captive screw connector
10-265-03
MBU 125 Under-desk mounting kit
70-077-01
RGB 580xi User’s Manual
IEC power cord
Windows-based control software
Tweeker
Optional AAP Devices
Description
Part number
RGB 580xi AAP 3' (black, white,
RAL9010 white)
70-128-02, -03, -05
RGB 580xi AAP 6' (black, white,
RAL9010 white)
70-129-02, -03, -05
RGB 580xi S AAP 3' (black, white,
RAL9010 white)
70-134-02, -03, -05
RGB 580xi S AAP 6' (black, white,
RAL9010 white)
70-135-02, -03, -05
RGB 580xi SI AAP 3' (black, white,
RAL9010 white)
70-137-02, -03, -05
RGB 580xi SI AAP 6' (black, white,
RAL9010 white)
70-138-02, -03, -05
ce-info@camboard.de
RGB 580xi • Specifications,
Parts, Accessories
A-5
im Vertrieb
von and Accessories, cont’d
Specifications,
Parts,
CAMBOARD Electronics
Optional Cable Cubby AAP Devices
Description
RGB 580xi Remote Interface
Part number
RGB 580xi CCS AAP 9' (black)
70-254-02
RGB 580xi CCS AAP 12' (black)
70-255-02
RGB 580xi CCSI AAP 9' (black)
70-256-02
RGB 580xi CCSI AAP 12' (black)
70-257-02
B
Optional RGB 580xi AAP Replacement Cables
These cables apply only to the RGB 580xi AAP,
RGB 580xi S AAP, and RGB 580xi SI AAP; they do
not apply to the RGB 580xi CCS AAP or RGB 580xi
CCSI AAP.
Appendix
RGB 580xi AAP replacement cable Part number
RGB 580xi AAP replacement cable 3' (0.9 m)
26-521-01
RGB 580xi AAP replacement cable 6' (1.8 m)
26-521-02
RGB 580xi AAP replacement cable 12' (3.6 m)
26-521-03
RGB 580xi AAP replacement cable 25' (7.6 m)
26-521-04
RGB 580xi AAP replacement cable 35' (10.6 m) 26-521-05
Mounting Template
RGB 580xi AAP replacement cable 50' (15.2 m) 26-521-06
Dimensions
A-6
www.camboard.de
RGB
580xi • Specifications, Parts, Accessories
Tel. 07131 911201
Fax 07131 911203
ce-info@camboard.de
im Vertrieb
Dimensions
for von
Mounting
CAMBOARD Electronics
Dimensions
For under-desk mounting, use the bracket mounting kit which
is included with the RGB 580xi, and refer to the template
illustration below.
The template shown here is not drawn to scale and is to be used for
dimensional reference only.
2.50"
(6.35 cm)
.
Not Drawn to Scale
7.10"
(18.034 cm)
RGB 580xi
Under-Desk Mounting
Bracket Template
B-2
www.camboard.de
RGB
580xi • Dimensions for Mounting
Tel. 07131 911201
Fax 07131 911203
ce-info@camboard.de
RGB 580xi
• Dimensions for Mounting
im Vertrieb von
www.camboard.de
CAMBOARD Electronics
Tel. 07131 911201
Fax 07131 911203
ce-info@camboard.de
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising