222 HARTREY AVE.. EVANSTON.
IL. 60204 U.S.A.
B
MICROPHONES AN0 ELECTRONIC COMPONENTS
AREA CODE
3121866.2200
TWX: 910-231 0048
.
CABLE:
SHUREMICRO
TELEX:
72-4381
THE PREMIER FAMILY OF STEREO SOUND REPRODUCERS
STEREO DYNETICB
KF-l
PHONOGRAPH CARTRIDGE
CARTRiDGE AND STYLUS SPECIFICATIONS
ed'$ p
N75-6
15a(.0006")
Spherical
Beige 6.2 n1V 2 0 t o
20,0800
Hz within
2 d B
N75-3t
64u(.O025")
Spher~cal
--
Dark
Green
-
-
6.2 mV
--
2 0 t o
20,000
Hz
-
20 d B at
1 k H z
-
1 t o 3 grams
1% to 3 grams
400 H z
1,000 H z -
10,000 H z
-
18 cm/Sec
25 cm/sec
- at 2 grams
?Optional 78 rpm Stylus: Set amplifier t o
"MONO''
o r "A-kB."
'Output voltages given for stereo cut record. For M O N O cut record, output voltage at both left channel and right channel cartridge terminals w i l l be 71% of figures above.
NET WEIGHT: 5.7 grams
INDUCTANCE: 720 millihenries
DC RESISTANCE: 630 ohms
OPTIMUM LOAD: 47,000 ohms resistance in parallel with 400 to 500 pico- farads total capacitance per channel. Load resistance can be up to 70,000 ohrns with almost n o audible change i n frequency response. Total capaci- tance includes both tone arm wiring and amplifier input circuit.
FOUR-CHANNEL: This Stereo Dynetic@ cartridge is compatible with all four-channel matrix systems.
MONOPHONIC OPERATION: Set function switch on amplifier to "MONO" or "A+B." I f amplifier is not equipped with this switch, connect left and right channels i n parallel.
CONNECTIONS (see Figure 1): Right "hot" lead (usually red) to "R," right ground (usually green1 to "RG." Left "hot" lead (usually white) to "L," left ground (usually blue) to "LC." I f metal head is causing ground loop hum, remove the ground tab. The metallic cartridge shield is disconnected from the right channel ground by the removal of the ground tab.
CAUTION: D o not make solder connection t o cartridge terminals.
STYLUS REPLACEMENT (see Fig- ure 2 ) : Grasp molded housing of stylus and gently pull forward out of cartridge. Insert replace- ment stylus into socket and press until housing mates with
cartridge
case.
MOUNTING L12.7 rnm (112 in.) mounting centers]:
Mounllng screws are provided.
1. Remove stylus guard and stylus
(see Stylus Replacement).
2 . Connect leads to cartr~dge (see
ENNEL
::ENEL
TERM'NAL
FIGURE 1
AGROUND TAB
TERMINAL
GROUNDED
TO CASE
3. Lay cartridge i n shell and a l ~ g n mounting holes on side of car- tridge w i t h holes o r threads i n shell. Follow turntable manu- iacturer's instruclions to mount cartridge i n tone arm o r plug-in shell.
4. Reinsert stylus (see Stylus Re- placement).
FIGURE 2
RECOMMENDED STYLUS CLEANING: Use a camel's hair brush (No. 2 slze o r smaller), trlmrncd to
approximately
6 mm (1/4 in.), dipped i n alcohol or an alcohol-distilled water solution.
Commercial
cleaning solutions may cdusf stylus darnage or corrosion. Always brush stylus irom back to front; never brush o r wipe stylus from front to back or side to side.
TO PRESERVE STYLUS LIFE:
1 . Follow turntable o r tone arm instructions when adjusling antiskating force.
2 . D o n o t handle [he tone arm while i t is i n operation since this may cause the arm to sweep across the record.
3 If ~t is necessary to manually place the tone arm i n the record groove while turntable is rotating, release 11 as soon as the stylus engages the record groove.
4. Correct improper set-down adjustment or malfunction of the turntable changing mechanism to prevent the stylus from striking the edge of the turntable o r record. D o not stack more records than turntable manufac- turer recommends.
5. Take care t o properly insert the stylus into the cartridge assembly and the cartridge and shell assembly into the tone arm receptacle.
6 . Use proper vertical tracking force setting for each cartridge.
7. D o not use badly warped, cracked or imperfect records.
8. When dusting the turntable protect the stylus with the stylus guard.
SPECIAL NOTE: To maintain the original performance standards of your cartridge, be certain that any replacement stylus you buy bears the follow-
Ing certification o n the package: "This Stereo Dynetic@ stylus is precision manufactured by Shure Brothers Inc." AVOID INFERIOR IMITATIONS. THEY
WILL SERIOUSLY DEGRADE THE PERFORMANCE OF YOUR CARTRIDGE.
ALL GENUINE "DYNETIC@" STYLI ARE MANUFACTURED BY SHURE
BROTHERS INC. LOOK FOR THE NAME SHURE O N THE STYLUS GRIP.
.
"A Visit t o the Small World of a ~ t y i u s . "
FULL ONE-YEAR WARRANTY: Shure Brothers lncorporated ("Shure"),
222 Hartrey Avenue, Evanston, Illinois 60204, warrants to the owner of this product that i t w i l l be free, i n normal use, of any defects i n workmanship and materials for a period of one year from date of purchase. You should retain proof of date of purchase. Shure is not liable for any consequential damages. If this Shure product has any defects as described above, care- fully repack the unit and return i t prepaid to:
Shure Brothers lncorporated
Attention: Service Department
1501 West Shure Drive
Arlington Heights, Illinois 60004
I f you are not i n the United States, return the unit to your dealer or
Authorized Service Center for repair. The unit w i l l be repaired o r replaced and returned to you promptly, and if i t cannot be repaired or replaced, you may elect to receive a refund. This warranty does not include stylus wear.
PATENT NOTICE: Cartridge and stylus manufactured under one o r more of the following U.S. patents: 3,055,988, 3,077,521, 3,077,522, and 3,463,889.
Copyright 1979, Shure Brothers Inc.
27A1539 (SH) Printed in U.S.A