Flashlogic FLC-IDS(RS) BM1 Remote Starter Install Guide
Below you will find brief information for Remote Starter FLC-IDS(RS) BM1. This device allows you to start your BMW or Mini from a distance using your factory key fob. You can also lock, unlock, and open the trunk from the key fob. This instruction manual will guide you through the installation and programming of your new remote starter.
advertisement
instaLL guiDe
FLC-IDS(RS)-BM1-EN
Document numbeR
12366
Revision Date
20131002
FiRmwaRe
FLC-IDS(RS)-BM1
haRDwaRe
FLRSBM1
accessoRies
PROGRAMMING CABLE FLPROG (REQUIRED)
FLRF1/2 (OPTIONAL)
CARLINK ASCL2 (OPTIONAL)
notice
The manufacturer will accept no responsability for any electrical damage resulting from improper installation of this product, be that either damage to the vehicle itself or to the installed device. This device must be installed by a certified technician. Please review the Installation Guide carefully before beginning any work.
Automotive Data Solutions Inc. © 2013
beFoRe instaLLation
1- Connect module to computer
2- Login to Weblink account
3- Flash firmware to module (module is not preloaded with firmware)
4- Use accessories accordingly (accessories are sold separately) www.flashlogic.com
VEHICLE LIST - 1 OF 1
FEATURES
Page 2 oF 16
DOC.: #12366
• 20131002
NOTES
I This fi rmware covers Automatic Transmission
(AT) vehicles only.
1 Series PTS AT
3 Series PTS AT***
5 Series PTS AT
6 Series PTS AT
1M PTS AT
M3 PTS AT***
M5 PTS AT
08-13 1 • • • • • • • • •
06-11 1 • • • • • • • • •
05-10 1 • • • • • • • • •
05-10 1 • • • • • • • • •
11 1 • • • • • • • • •
08-12 1 • • • • • • • • •
06-10 1 • • • • • • • • •
M6 PTS AT
X1 PTS AT***
X5 PTS AT
X5 Diesel PTS AT
X5 M PTS AT
X6 PTS AT
X6 M PTS AT
Z4 PTS AT***
Clubman PTS AT***
06-10 1
12-13 1
07-13 1
07-13 1
10-13 1
08-13 1
10-13 1
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
09-13 1 • • • • • • • • •
08-13 1 • • • • • • • • •
Cooper PTS AT***
Cooper Convertible PTS AT***
07-13 1
08-13 1
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
Coupe PTS AT***
Roadster PTS AT***
* If equipped with a factory hood switch.
** If equipped with an electric E-brake and it is activated, vehicle will shudown when a door is opened during RS sequence.
*** If equipped with the Confort Access System, the door handles will not be functional during RS sequence.
12-13 1 • • • • • • • • •
12-13 1 • • • • • • • • •
• • • • •
• • • • •
• • • • •
• • • • •
• • • • •
• • • • •
• • • • •
• • •
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
• • • • •
• • • • •
•
•
•
•
•
•
• • • • • • • • •
• • • • • • • • • •
• • • • • •
• • • • • •
• • • • • •
• • • • •
• • • • •
• • • • •
• • • • •
• • • • •
• • • • •
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
Automotive Data Solutions Inc. © 2013 FLC-IDS(RS)-BM1-EN www.flashlogic.com
BOX CONTENTS
MODULE
PROGRAMMING
BUTTON
A
B
C
D
LED 1
N
M
LED 2
H
G
J
I
L
K
EXPANSION PACK
E
F
XP LED 1 XP LED 2
O
P
ACCESSORIES (SOLD SEPARATELY)
PROGRAMMING CABLE (REQUIRED)
T-HARNESS 1
EXPANSION CABLE
BOX CONTENTS - 1 OF 1
10 PIN WHITE CONNECTOR
12 PIN BLACK CONNECTOR
AFTERMARKET HOOD SWITCH AND CABLE
Page 3 oF 16
DOC.: #12366
• 20131002
STICKER 1
STICKER 2
RF KIT (OPTIONAL)
COMPATIBLE MODELS ONLY
TELEMATICS DEVICE (OPTIONAL)
COMPATIBLE MODELS ONLY
Automotive Data Solutions Inc. © 2013 FLC-IDS(RS)-BM1-EN www.flashlogic.com
imPoRtant technicaL note - 1 OF 1
instaLL viDeo gaLLeRY avaiLabLe onLine
Before installing this product, consult our Install Video Gallery and watch:
•
Vehicle Disassembly Procedure videos
•
Module Connection Procedures videos
•
Module Programming Procedures videos
Simply visit our forum and register at http://www.12voltdata.com/forum/viewtopic.php?f=340&t=9683&sid=a61772b486e4584ad6f058b171ffa425
Page 4 oF 16
DOC.: #12366
• 20131002
Automotive Data Solutions Inc. © 2013 FLC-IDS(RS)-BM1-EN www.flashlogic.com
01
02
03
04
START vehicle. Verify all vehicle functionalities. If the vehicle displays error messages or any malfunction: stop the installation and service the vehicle.
Turn ignition to OFF position. Remove keyfob from keyport.
07
08
Verify all keyfob functionalities (Door Lock,
Door Unlock, Trunk Release and Comfort
Access System if equipped).
09
MODULE INSTALLATION PROCEDURE - 1 OF 1
Connect and secure every connector to the vehicle, as shown in STEP 1 of the WIRING
DIAGRAM.
13
WARNING: Any vehicle harness that is disconnected during installation, must be re-connected before performing any system tests. Failure to comply will result in vehicle displaying error messages. An OEM scantool will be required to clear the error messages.
START vehicle. Verify all vehicle functionalities.
14
15
Page 5 oF 16
DOC.: #12366
• 20131002
Connect the P connector to the module, as shown in STEP 3 of the WIRING DIAGRAM.
P
F
I
RF
If required, connect a compatible RF Kit, as shown in STEP 4 of the WIRING DIAGRAM.
If required, connect a compatible Telematics
Device, as shown in STEP 4 of the WIRING
DIAGRAM.
Insert the expansion pack into module.
10
05
Use the EXPANSION CABLE to connect the A connector to the module and the O connector to the expansion pack.
11
O
A
06
F
Connect the module to the computer with the programming cable (F port). Flash the module with the latest fi rmware then fl ash the expansion pack.
12
C
Automotive Data Solutions Inc. © 2013
WARNING: If the vehicle displays error messages or any malfunction, stop the installation, verify every connection and if the problem persists, call technical support.
Turn ignition to OFF position. Remove keyfob from keyport.
16
17
Connect the C connector to the module, as shown in STEP 2 of the WIRING DIAGRAM.
FLC-IDS(RS)-BM1-EN
18
If the vehicle is not equipped with a factory hood switch, install an aftermarket hood switch as shown in STEP 4 of the WIRING
DIAGRAM.
Put sticker 1 on a clean and visible surface in the engine bay and put sticker 2 under the dashboard near the OBDII connector.
Module installation procedure completed.
www.flashlogic.com
TYPE 1 - WIRING DIAGRAM - 1 OF 1
STEP 1:
CONNECT THE FOLLOWING TO THE VEHICLE
START THE VEHICLE WITH THE OEM KEYFOB
TO TEST THE CONNECTIONS
A1
A2
RELAY
Page 6 oF 16
DOC.: #12366
• 20131002
BRAKE SWITCH MODULE
N
M
C
D
O
A
B
P
L
K
J
I
H
G
WARNING
1-TO CONNECT THE MODULE: FOLLOW STEPS 1 TO 4
2-TO DISCONNECT THE MODULE: FOLLOW STEPS 4 TO 1
E
F
STEP 2:
CONNECT THE FOLLOWING TO THE MODULE
C
BLACK 20 PIN
P
STEP 3:
CONNECT THE FOLLOWING TO THE MODULE
WHITE 18 PIN
RELAY
H
07 GRAY/WHITE - HOOD STATUS (-) INPUT
08 GRAY/BLACK (NC)
F
I
BLACK 4 PIN - RF CABLE
BLUE 4 PIN - TELEMATIC CABLE
Automotive Data Solutions Inc. © 2013
4
3
2
1
BRAKE HARNESS
COMFORT ACCESS SYSTEM MODULE
MINI: BEHIND INSTRUMENT PANEL, DRIVER SIDE
BMW: UNDER DASH, DRIVER SIDE
STEP 4:
CONNECT THE FOLLOWING IF REQUIRED
IF NOT EQUIPPED
WITH AN OEM HOOD SWITCH,
INSTALL AN AFTERMARKET HOOD SWITCH
C1
C2
B1
B2
B1 CONNECTOR
B2 HARNESS
C1 CONNECTOR
WARNING:
THESE CONNECTORS HAVE TWO
[2X] LOCKING MECHANISMS.
INSERT THE CONNECTOR IN ITS
HOUSING AND APPLY GENTLE
PRESSURE ON BOTH EXTREMITIES
TO SECURE THE CONNECTION.
(TWO AUDIBLE CLICKS WILL BE HEARD.)
C2 HARNESS
AFTERMARKET HOOD SWITCH (-)
FLC-IDS(RS)-BM1-EN
RF KIT
TELEMATIC
www.flashlogic.com
01
02
03
04
05
LED 1 is solid RED. Insert keyfob 1 into keyport.
Within 10 seconds, LED 1 will fl ash GREEN once (1x).
08
Remove keyfob 1 from keyport.
09
LED 1 will turn solid RED. Wait 5 seconds.
Insert keyfob 1 into keyport.
07
MODULE PROGRAMMING PROCEDURE - 1 OF 1
Remove keyfob 1 from keyport.
10
11
WARNING: Follow steps 4, 3, 2 as shown in the wiring diagram to disconnect the module from the vehicle.
Connect module to computer and proceed with KLON programming.
WARNING: Follow steps 2, 3, 4 as shown in the wiring diagram to connect the module to the vehicle.
LED 1 will turn solid RED.
13
14
15
Insert keyfob 1 into keyport.
06
Within 10 seconds, LED 1 will fl ash GREEN rapidly.
12
Automotive Data Solutions Inc. © 2013 FLC-IDS(RS)-BM1-EN
Page 7 oF 16
DOC.: #12366
• 20131002
LED 1 will turn solid GREEN for 2 seconds.
Remove keyfob 1 from keyport.
Module Programming Procedure completed.
www.flashlogic.com
06
07
08
01
02
03
04
05
12
13
14
15
16
11
09
10
17
18
instaLLation checKList - 1 OF 2
Page 8 oF 16
DOC.: #12366
• 20131002
checKList
WARNING: Vehicle engine will start many times. Test in a well ventillated area.
Open driver door window for easy vehicle access.
Close all vehicle doors, hood and trunk.
Press LOCK button three times [3x] rapidly on the OEM keyfob to remote start vehicle.
Question 1: Does the vehicle remote start?
YES: Go to step 5.
NO: The module doesn't detect OEM remote lock button from the vehicle communication network. Check all connection, repeat step 4 and call technical support if the problem persist.
Press LOCK button three times [3x] rapidly on the OEM keyfob to shut down vehicle.
Question 2: Does the vehicle shut down?
YES: Go to step 6.
NO: Repeat step 5. If problem persists, push vehicle start button once [1x] to shut down the vehicle and call technical support.
Unlock and open driver door.
Press LOCK button three times [3x] rapidly on the OEM keyfob to remote start vehicle.
Question 3: Does the vehicle remote start?
YES: The module does NOT detect the door signal from the vehicle communication network. Press LOCK button three times [3x] rapidly on the OEM keyfob to shut down vehicle and call technical support.
NO: Go to step 8.
Open hood.
Question 4: Is the orange warning sticker "Sticker 1" placed under the hood?
YES: Leave hood open and go to step 9.
NO: Put the mandatory orange warning sticker "Sticker 1", leave hood open and go to step 9.
Close all doors.
Press LOCK button three times [3x] rapidly on the OEM keyfob to remote start vehicle.
Question 5: Does the vehicle remote start?
YES: Press LOCK button three times [3x] rapidly on the OEM keyfob to shut down vehicle. Go to Question 6.
NO: Go to step 11.
Question 6: Is the vehicle equipped with a factory hood switch? (Inside hood latch)
YES: The module does NOT detect the hood signal from the vehicle communication network. Call technical support.
NO: Install the mandatory hood switch included in the kit. Repeat installation checklist.
Close hood.
Enter vehicle. Do NOT press brake pedal.
Close all doors.
Press LOCK button three times [3x] rapidly on the OEM keyfob to remote start vehicle.
Wait for the vehicle to start.
Press brake pedal.
Question 7: Does the vehicle shut down?
YES: Go to step 17.
NO: The module does NOT detect the brake pedal signal from the vehicle communication network. Press LOCK button three times [3x] rapidly on the OEM keyfob to shut down vehicle and call technical support.
Apply parking brake.
Exit vehicle.
Automotive Data Solutions Inc. © 2013 FLC-IDS(RS)-BM1-EN www.flashlogic.com
instaLLation checKList - 2 OF 2
22
23
24
25
19
20
21
checKList
Close all doors.
Press LOCK button three times [3x] rapidly on the OEM keyfob to remote start vehicle.
Wait for the vehicle to start.
Question 8: Is the vehicle equipped with Comfort Access System ?
YES: For 1, 5, 6, X5, X6: Touch exterior driver door handle to unlock door using Comfort Access System. Within 45 seconds, go to step 22.
YES: For 3, X1, Z4, Mini: Press UNLOCK button once [1x] on the OEM keyfob. Within 45 seconds, go to step 22.
NO: Press UNLOCK button once [1x] on the OEM keyfob. Within 45 seconds, go to step 22.
Open driver door.
Question 9: Does the vehicle shut down?
YES: For Z4, X5, X6: Go to step 25.
YES: For 1, 3, 5, 6, X1: The module does NOT detect the parking brake signal or the unlock signal from the vehicle communication network. Call technical support.
NO: For Z4, X5, X6: The module does NOT detect the parking brake signal correctly from the vehicle communication network. Call technical support.
NO: For 1, 3, 5, 6, X1: Go to step 23.
Press and release brake pedal.
Push vehicle start button once [1x] to shut down the vehicle.
Installation checklist completed.
Page 9 oF 16
DOC.: #12366
• 20131002
Automotive Data Solutions Inc. © 2013 FLC-IDS(RS)-BM1-EN www.flashlogic.com
>>
01
NOTE: In Valet Mode, the Remote starter is not functional. Keyless entry, Lock and Unlock will remain functional. See RF kit user manual for alternate valet mode programming.
06
Insert keyfob into keyport.
07
VALET MODE PROGRAMMING PROCEDURE - 1 OF 1
Remove keyfob from keyport.
Valet Mode Programming Procedure completed.
To exit valet mode: repeat steps 1 to 6.
02
Time restriction. Complete next step within 5 seconds.
>>
03
STOP ACC ON START
Cycle ignition ON fi ve times [5x OFF/ON] rapidly. Parking Light will fl ash once [1x].
ENGINE
START
STOP
04
Wait, Parking Light will fl ash once [1x] to indicate that the valet mode is ON or twice [2x] to indicate that the valet mode is OFF.
05
STOP ACC ON START
Turn ignition to STOP position.
ENGINE
START
STOP
Automotive Data Solutions Inc. © 2013 FLC-IDS(RS)-BM1-EN
Page 10 oF 16
DOC.: #12366
• 20131002 www.flashlogic.com
aFteRmaRKet Remote PRogRamming: notes
I All aftermarket remotes must be programmed to the
RF-Kit.
Refer to the RF-Kit user guide for aftermarket remote features and programming procedures.
aFteRmaRKet Remote PRogRamming - 1 OF 1
Page 11 oF 16
DOC.: #12366
• 20131002
Automotive Data Solutions Inc. © 2013 FLC-IDS(RS)-BM1-EN www.flashlogic.com
>>
>>
>>
It is mandatory to exit the Module Navigation at the end of this procedure. Failure to exit the
Module Navigation will drain vehicle battery.
To exit the Module Navigation at any time:
Follow STEP 13.
Module must be programmed to the vehicle.
04
05
Use the Module Navigation Chart on the next page.
06
01
STOP ACC ON START
Set ignition to OFF position.
ENGINE
START
STOP
02
TO ACCESS THE MENUS: Press and hold programming button until LED 1 turns solid
GREEN.
07
08
03
[X]
IN THE MENUS: Press the programming button as many times as the menu number indicates. LED 1 will fl ash GREEN an equal amount of times continuously.
Automotive Data Solutions Inc. © 2013
09
MODULE NAVIGATION PROCEDURE - 1 OF 1
TO ACCESS THE OPTIONS: Press and hold programming button until LED 1 turns solid
RED.
10
[Y]
IN THE OPTIONS: Press the programming button as many times as the option number indicates. LED 1 will fl ash RED an equal amount of times continuously.
TO ACCESS THE SETTINGS: Press and hold programming button until LED 1 turns solid
GREEN.
11
12
[Z]
LED 1 will flash GREEN as many times as the current (or default) setting number, continuously.
13
[Z]
IN THE SETTINGS: Press the programming button as many times as necessary to access your setting. LED 1 will fl ash GREEN an equal amount of times continuously.
To return to the MENUS: exit the Module
Navigation and redo the Module Navigation
Procedure.
14
>>
FLC-IDS(RS)-BM1-EN
Page 12 oF 16
DOC.: #12366
• 20131002
To save and return to the OPTIONS: Press and hold programming button until LED 1 turns solid RED.
[Y]
LED 1 will fl ash RED as many times as the current option number continuously.
Configure every other setting and proceed to step 13.
MANDATORY: EXIT MODULE NAVIGATION.
Press and hold programming button for 7 seconds. LED 1 will fl ash RED rapidly. Release programming button. LED 1 will turn OFF.
Module navigation completed.
Failure to exit the Module Navigation will drain vehicle battery.
www.flashlogic.com
moDuLe navigation chaRt - 1 OF 1
Page 13 oF 16
DOC.: #12366
• 20131002
moDuLe navigation chaRt: notes
I Default settings are listed in bold.
II Make sure the option is covered on the vehicle before attempting to change the setting.
*Vehicle will shutdown when a door is opened.
Automotive Data Solutions Inc. © 2013
01 CONFIGURATION
02-07 Technical Support only
FLC-IDS(RS)-BM1-EN
01
02
03
04
05
06
07
08
09
DISARM/UNLOCK BEFORE START
RELOCK AFTER START
RELOCK AFTER SHUTDOWN
FORCE UNLOCK ALL ON FIRST PRESS
TAKEOVER
SECURE TAKEOVER DELAY
FACTORY KEYLESS RS SEQUENCE
MODULE RUN TIME
WAIT TO START DELAY
10-15 N/A
01 N/A
01
02
03
04
01
02
03
04
02
01
02
03
04
01
02
01
02
01
02
01
02
01
05
06
07
08
01
02
03
04
05
06
07
08
01
01
25 MIN
30 MIN
35 MIN
15 min
02 sec
05 SEC
08 SEC
10 SEC
15 SEC
20 SEC
25 SEC
30 SEC
N/A
N/A
oFF
ON
oFF
ON
oFF
ON
oFF
ON
enabLe
DISABLE*
45 sec
90 SEC
03 MIN
04 MIN
DISABLE
N/A
LOCK + UNLOCK + LOCK
LocK + LocK + LocK
03 MIN
05 MIN
10 MIN
15 MIN www.flashlogic.com
Remote staRteR eRRoR coDes - 1 OF 1
Remote staRteR eRRoR coDes: notes
I WARNING: The following applies only when the parking lights are connected and supported by the system.
II After a remote starter failure, the parking lights will fl ash
[X] number times to indicate an error code. See table.
09
10
11
12
13
14
15
16
03
04
05
06
07
08
[X] numbeR oF PaRKing Light FLashes
Foot brake is ON.
Hood is open.
Engine tach signal is lost.
System is in Valet Mode.
Vehicle is moving (VSS).
Glow plug timeout error.
RS not synchronized. Start vehicle with OEM key for 15 sec before trying a new RS sequence.
N/A
N/A
N/A
N/A
N/A
N/A
CAN communication failure during RS sequence.
Page 14 oF 16
DOC.: #12366
• 20131002
Automotive Data Solutions Inc. © 2013 FLC-IDS(RS)-BM1-EN www.flashlogic.com
moDuLe Diagnostics - 1 OF 1 test moDuLe
I DURING PROGRAMMING
II DURING REMOTE START
III WITH IGNITION OFF
Flashing RED
Solid RED
Flashing GREEN
Solid GREEN then OFF
OFF
Flashing RED
Solid RED
Flashing GREEN
Solid GREEN then OFF
OFF
Flashing RED
Solid RED
Flashing GREEN
Solid GREEN then OFF
OFF
Missing/wrong information from fi rmware or vehicle.
Module waiting for more vehicle information.
Additional steps required to complete module programming.
Module correctly programmed.
No activity or module already programmed.
Module incorrectly programmed.
Module incorrectly programmed.
Module correctly programmed and operational.
Reset in progress.
Invalid ground when running status from remote starter.
Module incorrectly programmed or connected.
Module not programmed. Waiting for more vehicle information.
False ground when running status from remote starter.
Reset in progress.
Module at rest and ready for a remote start sequence.
Page 15 oF 16
DOC.: #12366
• 20131002
Automotive Data Solutions Inc. © 2013 FLC-IDS(RS)-BM1-EN www.flashlogic.com
01
02
03
04
Disconnect all connectors from module except the BLACK 20-PIN connector.
07
MODULE RESET PROCEDURE - 1 OF 1
Reconnect all connectors.
Disconnect the BLACK 20-PIN connector.
08
Repeat programming procedure.
PRESS AND HOLD programming button while connecting the BLACK 20-PIN connector.
Wait, LED 1 will flash RED. RELEASE programming button.
LED 1 will turn RED for 2 seconds.
>>
Failure to follow procedure may result with a
DTC or a CHECK ENGINE error message.
05
06
Module RESET completed.
Automotive Data Solutions Inc. © 2013 FLC-IDS(RS)-BM1-EN
Page 16 oF 16
DOC.: #12366
• 20131002 www.flashlogic.com
advertisement
Key Features
- Remote start from OEM remotes
- Secure takeover
- Data Immobilizer bypass
- Arm OEM alarm
- Disarm OEM alarm
- Door lock
- Door unlock
- Trunk/hatch release
- Parking light control
Frequently Answers and Questions
How do I program the remote starter?
What vehicles are compatible with this remote starter?
What accessories are required for this remote starter?
Related manuals
![Omega Link OEM-IDS(RS)-BM1-[OL-RS-BM1]-EN Install Manual](http://s3.manualzz.com/store/data/054732371_1-1f6580174f560a1502698ef056117b14-150x150.png)
advertisement