InfinityEdge™ 5” and 7” In-Wall

Touch Screen

Installation Guide

Introduction

The Control4 ® InfinityEdge™ 5” or 7” In-Wall Touch Screens offer complete system control in an elegant and compact design. These Touch Screens are equipped with a capacitive

Touch Screen surface and four (4) programmable shortcut buttons. The power options are AC power or Power-Over-Ethernet (PoE). The device may be connected via WiFi or

Ethernet. Available for new construction or retrofits.

Supported Models

• C4-TSWMC5 – InfinityEdge 5” In-Wall Touch Screen

• C4-TSWMC7 – InfinityEdge 7” In-Wall Touch Screen

Associated SKUs:

• C4-TSWMC5-EG-WH – InfinityEdge 5” In-Wall Touch Screen, White

• C4-TSWMC5-EG-BL – InfinityEdge 5” In-Wall Touch Screen, Black

• C4-TSWMC7-EG-WH – InfinityEdge 7” In-Wall Touch Screen, White

• C4-TSWMC7-EG-BL – InfinityEdge 7” In-Wall Touch Screen, Black

What’s in the Box

Carefully unpack the contents of the box, and make sure the following items are included in the box. If any item is missing or damaged, please contact your Control4 Reseller.

• InfinityEdge 5” or 7” In-Wall Touch Screen

• InfinityEdge power box (used to power the Touch Screen)

• Two (2) Orange wire nuts

• InfinityEdge 5” and 7” In-Wall Touch Screens Installation Guide (this document)

Wall Box Kit Options

There are four (4) wall box options available to install this Touch Screen. Metal and plastic wall boxes are available for new construction or retrofit installations.

•

InfinityEdge 5” or 7” In-Wall Touch Screen Wall Box Kits - New Construction

Plastic Model (C4-NWB57C-P)

Metal Model (C4-NWB57C-M)

•

InfinityEdge 5” or 7” In-Wall Touch Screen Wall Box Kit - Retrofit

Plastic Model (C4-RWB57C-P)

Metal Model (C4-RWB57C-M)

Refer to the Control4 InfinityEdge 5” or 7” In-Wall Touch Screen Wall Box Installation

Guide - New Construction or InfinityEdge 5” or 7” In-Wall Touch Screen Wall Box Installa-

tion Guide - Retrofit for your wall box installation instructions.

Accessories

• Control4 Power Over Ethernet Injector, sold separately (AC-POE1-B)

• InfinityEdge 5” and 7” In-Wall Touch Screens Wall Box New Construction, Plastic

(C4-NWB57C-P)

• InfinityEdge 5” and 7” In-Wall Touch Screens Wall Box New Construction, Metal

(C4-NWB57C-M)

• InfinityEdge 5” and 7” In-Wall Touch Screens Wall Box Retrofit, Plastic

(C4-RWB57C-P)

• InfinityEdge 5” and 7” In-Wall Touch Screen Wall Box Retrofit, Metal

(C4-RWB57C-M)

Important Safety Instructions

5.

6.

7.

1.

2.

3.

4.

8.

9.

10.

11.

12.

Read and keep these instructions.

Heed all warnings and follow all instructions.

Do not use this apparatus near water.

Clean only with a dry cloth.

Install in accordance with the manufacturer’s instructions.

Install in accordance with all national and local electrical codes.

This product is also designed for IT power systems with phase-to-phase voltage

120V or 240V.

Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat.

Only use attachments/accessories specified by Control4.

If applicable, unplug this apparatus during lightning storms or when unused for long periods of time.

This product is to be installed by qualified professionals only.

Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.

WARNING! The Touch Screen must be protected by an external circuit breaker or a fuse rated at 6A maximum when used in Europe.

Avertissement! Pour réduire le risque du feu ou de choc électrique, n’exposez pas cet appareil à la pluie ou à l’humidité.

Warnung! Die Berührungseingabe muß durch einen externen Circuit breaker oder eine Sicherung geschützt werden, die am Maximum 6A veranschlagen wird, wenn sie in Europa verwendet wird.

WARNING! Do not place the Touch Screen near sources of heat or expose to direct sunlight for an extended period of time.

Avertissement! Ne placez pas l’unité près des sources de chaleur ou exposition pour diriger la lumière du soleil pendant une période prolongée.

Warnung! Setzen Sie Maßeinheit nicht nahe Quellen der Hitze oder des Exposés, um Tageslicht während eines ausgedehnten Zeitabschnitts zu verweisen.

IMPORTANT! Do not use pens or sharp objects to navigate or make selections on the Touch Screen. To select an item or scroll through a list, use your fingertip.

Important! N’employez pas les stylos ou les objets pointus pour diriger ou pour faire des choix sur l’écran. Pour choisir un article ou un rouleau par une liste, employez votre bout du doigt.

Wichtig! Benutzen Sie nicht Federn oder scharfe Gegenstände, um oder Vorwähleren auf dem Schirm zu bilden zu steuern. Um ein Einzelteil oder eine Rolle durch eine Liste vorzuwählen, benutzen Sie Ihre Fingerspitze.

IMPORTANT! Improper use or installation can cause LOSS/DAMAGE OF

PROPERTY.

Important! L’utilisation ou l’installation inexacte peut causer LOSS/DAMAGE DE

PROPRIÉTÉ.

Wichtig! Unsachgemäßer Gebrauch oder Installation können LOSS/DAMAGE

DER EIGENSCHAFT verursachen.

IMPORTANT! Using this product in a manner other than outlined in this document voids your warranty. Further, Control4 is NOT liable for any damage incurred with the misuse of this product. See “Warranty.”

Important! Utilisant ce produit en quelque sorte autre que décrit dans ce document vide votre garantie. De plus, Control4 n’est pas responsable d’aucun dommage encouru avec l’abus de ce produit. Voyez que «Warranty.»

Wichtig! Das Verwenden dieses Produktes in gewissem Sinne anders als umrissen in diesem Dokument hebt Ihre Garantie auf. Weiter ist Control4 NICHT für irgendeine Beschädigung verantwortlich, die mit der Fehlanwendung dieses

Produktes genommen wird. Sehen Sie, daß “Warranty.”

WARNING! Install in accordance with all national, state, and local electrical codes.

Avertissement! Installez selon tous les national, état, et codes électriques locaux.

WARNING! This product generates heat. The room must have adequate ventilation or the ability to dissipate heat effectively.

Avertissement! Ce produit produit de la chaleur. La salle doit avoir à ventilation proportionnée ou la capacité d’absorber la chaleur efficacement.

WARNING! This product must be grounded in accordance with the National

Electrical Code (NEC) requirements.

Avertissement! Ce produit doit être fondu selon les conditions électriques nationales de code (NEC).

WARNING! Use this product only in dry locations.

Avertissement! Employez ce produit seulement dans des endroits secs.

CAUTION! This product is for residential use only.

Attention! Ce produit est pour à l’usage résidentiel ou commercial seulement.

MAGNET WARNING! Located within the plastic enclosures of this product are strong (rare earth) magnets that are used to attach the face plate to the electrical box. If someone handling or using the product has a pacemaker, defibrillator, or similar electronic device used for health purposes, avoid close proximity (closer than 20 inches) to the product until you consult your physician. Magnetic fields can cause damage to magnetic storage media (for example, credit cards, video tapes, computer hard drives, etc). Keep all magnets at least 20 inches away from all types of magnetic media. Certain electronic devices are sensitive to magnetic fields and may be damaged permanently or temporarily disabled if exposed to a magnetic field that is too strong. Consult the owner’s manuals of your electronic devices for further information.

Ingested magnets can cause serious injuries and may result in death. If magnets have been ingested (or you suspect they might have been), seek competent medical attention immediately.

Avertissement - Aimants! Dans l’emballage en plastique de ce produit sont inclus des aimants très puissants utilisés pour attacher les plaques de surface aux boites électriques. Si quelqu’un, manipulant ou utilisant ce produit est muni d’un pacemaker, défibrillateur ou autre dispositif d’ordre médical, il doit éviter de se trouver à proximité (moins de 20 pouces) de ce produit avant d’avoir consulté son médecin. Les champs magnétiques des aimants peuvent endommager le stockage d’information d’ordre magnétique (ex : cartes de crédit, bandes vidéo, disques durs d’ordinateur, etc.) Gardez tous les aimants au moins à 20 pouces de distance de tout type de stockage d’information d’ordre magnétique. Certains dispositifs électroniques sont sensibles aux champs magnétiques et peuvent être endommagés de façon permanente ou être désactivés si ils sont exposés à un champs magnétique trop puissant. Pour plus d’information, consultez le manuel d’utilisateur propre à votre pièce électronique.

Si avalés, les aimants peuvent causer des blessures graves et aussi causer la mort. Si des aimants ont été avalés (ou vous doutez qu’ils ont pu l’être) obtenez les soins médicaux de personnes compétentes immédiatement.

Figure 1. Touch Screen Placement

New Device

AC Power (unless using PoE)

This device uses an Ethernet or WiFi network connection, and can be powered using

PoE or AC power.

Note: Do not attempt to use PoE and AC at the same time.

Option 1: Ethernet Connection with a PoE Injector or a

Third-Party Injector or Switch

PoE injects electrical current into the Ethernet cable using a PoE Injector (model

#AC-POE1-B) or a third-party PoE solution to provide the Touch Screen with power and a network connection. The InfinityEdge 5” and 7” Touch Screens work with the Control4

PoE Injector or a third-party PoE Injector. To set up your PoE and Ethernet connection with a PoE Injector, see Figure 2.

Figure 2. Ethernet Model - Requires Ethernet Connection to PoE Injector

Place the PoE Injector near your gateway/router/switch. Pull the Ethernet cable from that location to where you want to install the Touch Screen.

Option 2: Ethernet Connection with AC

No PoE Injector is needed for Ethernet with AC power; the Ethernet is connected directly to the switch. This power connection requires both neutral and hot connections (see

Figure 3).

Figure 3. Ethernet - Requires Connection to Ethernet and AC Power

Requirements for In-Wall Installations

To install the InfinityEdge 5” or 7” Touch Screen, you need the following:

• Home Controller HC-200, HC-300, HC-1000, Commercial Controller CC-300, or

CC-1000 fully installed and configured with a Control4® system.

• Control4 InfinityEdge 5” and 7” Touch Screen custom wall box installed. See “Wall

Box Kit Options” in this document.

• If using Ethernet with PoE power:

• Ethernet network.

• Control4 PoE Injector (model #AC-POE1-B) or another third-party PoE Injector or switch (which are certified to UL/ANSI standards).

• Two (2) Ethernet CAT5 cables to support your PoE Injector: (1) one that runs from the Ethernet gateway/router/switch to the PoE Injector/switch and (2) one that runs from the PoE Injector/switch to the Ethernet Touch Screen wall box.

• If using Ethernet with AC power:

• An Ethernet network installed and available that includes a gateway/router/switch.

• Access to in-wall AC power (a neutral connection is required).

• One (1) Ethernet CAT5 cable that runs from the Ethernet gateway/router/switch to the Touch Screen.

• If using wireless with AC power:

• Wireless network (WiFi 802.11 b/g) installed and available with a wireless access point (WAP).

• Access to in-wall AC power (a neutral connection is required).

• A 14-gauge electrical wire long enough to pull between the Touch Screen and the power source.

Placement, Network Connection, and Power

Options

Place the Touch Screen in a convenient location at eye level, typically near the entrance of the room, approximately 57 to 61 inches from the floor (see Figure 1).

Option 3: WiFi Connection with AC

WiFi placement: Place the Touch Screen above a power source, for example, an outlet.

Ensure that you have WiFi in the home (see Figure 4).

Figure 4. WiFi - Requires AC Power and WAP

Front and Rear Panel Description

Front View

Figure 5. Front View of the InfinityEdge 5” or 7” In-Wall Touch Screen

1

2

3

1

2

3

Display: 5” or 7” viewing area, Touch Screen with 800 x 480 resolution.

Shortcut buttons (4): For custom programming; to initiate an action or sequence of actions.

Touch Screen Removal: Small hole located under the Touch Screen to remove the

Touch Screen from the wall.

Front dimensions. 5” Touch Screen (H x W x D): 3.15” x 4.8 x 0.8” (80mm x 122mm x 20mm); 7” Touch Screen (H x W x D): 4.6” x 6.9 x 0.9” (117mm x 175mm) x 23mm)

Wall box dimensions. 5” or 7” Touch Screens (H x W x D): 2.7” x 4.1” x 2.4”

(68mm x 104mm x 61mm)

Power box dimensions. 5” or 7” Touch Screens (H x W x D): 2.8” x 4.5” x 1.8”

(71mm x 114mm x 46mm)

Back View

Figure 6. Back View of InfinityEdge 5” or 7” In-Wall Touch Screen and Power Box

1

2

1

2

Wireless Connection: Hot (H) uses Black wire; Return (R) uses White wire.

RJ-45 port for Ethernet Connection: Ethernet port available for either a standard

Ethernet source that provides network communication only OR a PoE source that provides power to the device and network communication.

Installation

WARNING! For the location where you are installing the Touch Screen, switch off the circuit breaker or remove the fuse from the fuse box.

Avertissement! Pour l’endroit où vous installez l’écran tactile, coupez le disjoncteur ou enlevez le fusible de la boîte de fusible.

Warnung! Für die Position, in der Sie die Berührungseingabe anbringen, den

Circuit breaker ausschalten oder die Sicherung vom Sicherung Kasten entfernen.

IMPORTANT! When cutting the opening for the wall box, DO NOT cut the opening too large. Be conservative and cautiously enlarge it as needed.

Important! En coupant l’ouverture pour la boîte de mur, ne coupez pas l’ouverture trop grande. Soyez conservateur et agrandissez-avec précaution la comme nécessaire.

Wichtig! Wenn Sie die öffnung für den Wandkasten schneiden, schneiden Sie

NICHT die große öffnung zu. Seien Sie konservativ und vergrößern Sie es vorsichtig, wie gebraucht.

IMPORTANT! Before you can complete these instructions below, you must have a Control4 5” or 7” Touch Screen wall box installed according to the documentation provided in the wall box kit. See “Accessories” for details.

Important! En coupant l’ouverture pour la boîte de mur, ne coupez pas l’ouverture trop grande. Soyez conservateur et agrandissez-avec précaution la comme nécessaire. Voyez que <<Accessories>>.

Wichtig! Bevor Sie diese Anweisungen durchführen können, müssen Sie ein

Control4 7 haben“ der Berührungseingaben- Wandkasten, der entsprechend den

Unterlagen angebracht wird, die in den Wandkasteninstallationssatz bereitgestellt werden. Sehen Sie daß “Accessories.”

•

PoE: The Ethernet network connection is provided by the PoE Injector. No

•

additional wiring is needed.

Standard Ethernet Connection: Connect the Touch Screen to one of the RJ-45

•

LAN ports on the gateway/router using the RJ-45 Ethernet cable.

WiFi Connection: The internal WiFi antenna will communicate with the LAN’s WAP.

If the LAN has a WAP set up, no additional wiring is needed.

1

•

AC Power. AC power is used to power the Touch Screen when using an Ethernet

•

or WiFi network connection.

Power Over Ethernet (PoE). PoE is used to power the Touch Screen when using an Ethernet or WiFi network connection.

Prepare the plastic power box for installation into the wall box by inserting either the

Ethernet cable or the AC power cable into the power box (see Figures 7 and 8).

AC Power Connection. The steps below represent a typical U.S. installation.

Connect wires to the AC power source for the Touch Screen according to your national and local electrical codes. Your installation may require alternative wires and the use of a terminal block.

a.

Thread the power cable through the bottom back hole of the wall box to the terminal (Figure 7). Remove the tab covering the hole first.

b.

Using the orange wire nuts (shipped in the box) connect the white-to-white wire and the black-to-black wire, and then cap each one with a wire nut. Strip the wire to 1/4” if necessary.

c.

Cap the ground wire from the wall if you are using a plastic wall box.

Figure 7. AC Power Connection

Black and White Wires

Ethernet Connection

Power Cable

Power Box

Wall Box d.

e.

Align and bend the wires carefully to fit them inside the wall box.

Align and carefully slide the power box into the wall box.

Power Over Ethernet (PoE) Connection. Install a PoE Injector (sold separately) or switch, and then connect the PoE Injector to the power and network. Connect to the power box. The steps below describe how to install a Control4 PoE Injector.

a.

b.

Connect the Control4 PoE Injector to a power source, for example, an AC outlet, using the power cord (provided with the unit). The PWR mode light on the PoE

Injector is orange and the STAND BY light is green.

Connect one of the RJ-45 LAN ports on the gateway/router/switch to the PoE

Injector’s LAN port using the RJ-45 Ethernet cable. c.

Connect the PoE Injector’s PWR LAN-OUT port to the RJ-45 Ethernet cable that will be connect to the Touch Screen. When the Touch Screen is in the power box, the PWR mode LED will change from orange to green.

d.

e.

Pull the Ethernet cable through the top back hole of the wall box to the Ethernet connector on the top back of the power box, and then connect it (see Figure 8).

Align and carefully slide the power box into the wall box. Unless the Touch

Screen is in the power box, it doesn’t pull any power.

Figure 8. Ethernet Connection

2

3

4

Secure the power box into the wall box using the screws provided with the power box.

Align and slide the back of the Touch Screen into the power box. The Touch Screen is magnetic and should snap right into place.

(Optional) To secure the Touch Screen inside the power box, remove the tape covering the bottom security pin (see Figure 9) before attaching the Touch Screen to the power box.

5 Note the pinhole on the bottom underside of the Touch Screen’s faceplate. If you ever need to remove the Touch Screen from the wall, do the following: a.

Locate the small pinhole on a tab (right side) underneath the Touch Screen. b.

Insert a paper clip into the hole (about 1/4”). With both hands, lift the Touch

Screen from the bottom of the screen toward you to remove it (see Figure 9).

Figure 9. Touch Screen Pin and Pinhole

Security pin

6

7

Speaker Insert paper clip here to remove Touch Screen

To protect the screen’s display: Use one of the screen-saver options available from the More > Settings > Screen Saver page.

(WiFi only) Connect to a WAP on the Touch Screen (see Figure 10): a.

Select More > Settings >

Network. The Wireless configuration screen appears.

Figure 10. Wireless Configuration b.

c.

Under Wireless, select

Enable. If you don’t see the network you want, select

Other.

At Network Name, select to add the SSID or wireless network when the keyboard appears. Select Done.

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is

•

• encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.

Increase the separation between the equipment and receiver.

•

Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

Consult the dealer or an experienced radio/TV technician for help.

Australia/New Zealand Compliance

•

AS/NZS CISPR 22:2006

IMPORTANT! Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate this equipment.

Third-Party Trademarks

Libertas

Libertas Firmware copyright statement for Touch Screens 6/26/09

Copyright (c) 2006, One Laptop per Child and Marvell Corporation.

All rights reserved.

Redistribution. Redistribution and use in binary form, without modification, are permitted provided that the following conditions are met:

* Redistributions must reproduce the above copyright notice and the following disclaimer in the documentation and/or other materials provided with the distribution.

* Neither the name of Marvell Corporation nor the names of its suppliers may be used to endorse or promote products derived from this software without specific prior written permission.

* No reverse engineering, decompilation, or disassembly of this software is permitted.

* You may not use or attempt to use this software in conjunction with any product that is offered by a third party as a replacement, substitute or alternative to a Marvell Product where a Marvell Product is defined as a proprietary wireless LAN embedded client solution of Marvell or a Marvell Affiliate.

DISCLAIMER. THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND

CONTRIBUTORS “AS IS” AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUD-

ING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND

FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL

THE COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT,

INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES

(INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR

SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION)

HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT,

STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING

IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE

POSSIBILITY OF SUCH DAMAGE.

d.

e.

At Security, select None, WEP 64, WEP 128, or WPA. At Password, type the password given to you by the person who set up your home’s wireless network

(Control4 Dealer or Installer) on the keyboard that appears. Press Done.

Select Connect. Notice that the IP settings change. The IP address is set to

DHCP by default.

(Optional) If you need to set a static IP address instead, complete the following steps:

•

On the Network page, press Static.

Select each box one at a time and type the address: IP Address, Subnet

Mask, Default Gateway, Preferred DNS, and Alternate DNS. When the keyboard appears, type the address, and then press Done.

f.

Press OK to return to the Network page. You can now connect to a Control4

Director running on a Control4 device on the network.

g.

Press OK.

8 When your Touch Screen is physically installed and appears on the home network, you can add and configure it to the Control4 System using the Composer Pro software. See the Composer Pro User Guide for information about how to add and identify the Touch Screen to the Control4 System.

Restore the Touch Screen to Factory Default

There are two ways to perform a factory restore on the InfinityEdge 7” Touch Screen:

1. Press and hold the red 4 button upon start up, and follow the instructions presented

on the screen to initiate the factory restore process and reset the Touch Screen to the

factory default settings.

2. On the back of the Touch Screen, there is a small switch labeled “Factory Restore.”

By changing the position of this switch and reattaching the Touch Screen to the power

box in the wall, the Touch Screen will reboot and the factory default firmware image will

be installed. All settings will reset to the factory default settings.

Regulatory Compliance

FCC/Industry Canada

FCC ID: R33D2 (InfinityEdge 5” In-Wall Touch Screen); R33D3 (InfinityEdge 7” In-Wall

Touch Screen)/Canadian ID: 7848A-D2 (InfinityEdge 5” In-Wall Touch Screen); 7848A-D3

(InfinityEdge 7” In-Wall Touch Screen)

This device complies with Part 15 of the FCC Rules Sub-Part A and B and with

Canada ICES-003 and RSS-Gen. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

GNU GENERAL PUBLIC LICENSE TERMS AND CONDITIONS FOR COPYING, DISTRI-

BUTION AND MODIFICATION (Section 3.b.)

You may copy and distribute the Program (or a work based on it, under Section 2) in object code or executable form under the terms of Sections 1 and 2 above provided that you also do one of the following:

Accompany it with a written offer, valid for at least three years, to give any third party, for a charge no more than your cost of physically performing source distribution, a complete machine-readable copy of the corresponding source code, to be distributed under the terms of Sections 1 and 2 on a medium customarily used for software interchange.

The complete text for this license is available on the Control4 web site at: http://www.

control4.com.

Protected under U.S. Patents 7,335,845, 7,106,261 and licensed under U.S. Patents

5,905,442 and 5,982,103

Recycling

For information about Control4’s recycling program, go to: www.control4.com/recycling.

Warranty

Limited 2-year Warranty. Refer to http://www.control4.com/warranty.

About this Document

©2010 Control4. All rights reserved. Control4 and the Control4 logo are registered trademarks and InfinityEdge is a trademark of Control4 Corporation in the United States and/or other countries. All other names or brands may be claimed as property by their respective owners. Pricing and specifications subject to change without notice.

Part Number: 200-00164 Rev F 9/15/2010