CENTURION Full Product Catalogue Sliding Gate Operators

CENTURION Full Product Catalogue Sliding Gate Operators
slidING
GATE
OPERATORS
Centurion Systems’ range of technologically advanced
sliding gate operators have been designed to automate
virtually any sliding gate and suit a wide variety of
applications; from private residences where the gate
is only operated infrequently, to large complexes,
businesses and industrial installations where the gate
could almost be used constantly. Each and every
operator offers functionality far beyond the scope of
simply opening and closing your gate, putting a world of
control literally at your fingertips.
This quick selection guide will help you to select the perfect CENTURION for you or your client’s sliding gate by providing the
differentiating features and key specifications of each.
Input voltage
Mains power required at gate
Gate mass – maximum
Gate speed – maximum
Duty cycle – mains present
Daily operations - maximum
Interface type
D2 Turbo
D2 Turbo LowVoltage
D5-Evo
D5-Evo LowVoltage
D10
D10 Turbo
A10 Endurance
A10 Heavyweight
90V - 240V AC
10V - 20V AC
10V - 28V DC
90V - 240V AC
15V - 19V AC
90V - 240V AC
90V - 240V AC
220V - 240V AC
220V - 240V AC
√
-
√
-
√
√
√
√
250kg
24m/min
250kg
24m/min
500kg
22m/min
500kg
22m/min
1000kg
26m/min
1000kg
50m/min (varies with
load)
Standard
speed
Sprint
speed
1000kg
600kg
Standard
speed
Sprint
speed
16m/min
30m/min
SLIDING GATE OPERATOR
quick selection guide
Sliding Gate Operator Quick Selection Guide
Sprint Speed
Sprint speed
50% 1
50% 1
50% 1
20% 1
25% 1
45% 1
80%
80%
10 2
10 2
150 2
30 2
750 2, 3
750 2, 3
Only limited by duty cycle
Only limited by duty cycle
LED-based
Dial-based
Dial-based
LCD
LCD
LCD
LCD
LED-based
Time-barring and automatic activation
-
-
√
√
√
√
-
-
Onboard multichannel receiver
√
√
√
√
√
√
-
-
1. Based on a 25° ambient temperature and unit not in direct sunlight
2. Battery-driven typically using a 7Ah (5Ah – D2 Turbo/D2 Turbo Low-Voltage) battery and a charger (battery can be upgraded for greater power failure autonomy –
mounted separately). Solar power may also be used.
3. With a brush replacement interval of two years
www.CentSys.com
sliding
gate operator
quick selection
guide
page 9
Technical Specifications
Product Code: D2TB0000V2
Technical Data
The D2 Turbo is a high-speed, cost-effective operator for domestic gates weighing up to 250kg, with a maximum speed of 24
metres per minute and powerful push force of 18kgf. This operator is exceptionally quick and easy to install and set up, with all
settings easily configurable via two dials on the controller.
With loads of features, the D2 Turbo is the complete motor for a standard, domestic four metre gate.
Input voltage 1
Motor voltage
Motor power supply 2
Battery charger 1
Current consumption (mains)
Current consumption (motor at rated load)
Main Features
Operator push force - starting
Mechanical Features
• High-security cleared beam Autoclose, in conjunction with
Safety Beams (PIRAC)
• Battery backup
• Automatic closing with adjustable time delay, and
pushbutton override
• Turbo speed for greater security and convenience
• Tough-as-nails steel pinion
• Easy mounting with a revolutionary jacking system
• Remote gate-status indicator (gate position, power failure,
low battery, multiple collision detection and Pillar Light Status
indication)
• Lockable, easy manual override
• Pedestrian Opening
• Stylish design enhances any entrance
• Holiday Lockout
• Modular components clip together for easy maintenance
• Courtesy/Pillar Light (fixed duration), with pre-delays and
two Pre-flashing Modes
• Very easy to install and set up, saving you time and money
Electronic Features
• Ant-proof controller housing with removable terminals
• Onboard multichannel CENTURION code-hopping receiver
with the ability to learn remote control buttons to specific
functions (e.g. Gate Trigger, Pedestrian Opening, Holiday
Lockout)
• Adaptive Collision Sensing – intelligent enough to adapt to
changes in the track, but sensitive enough to keep your loved
ones safe
• Opening and Closing Safety Beam Inputs with beam circuit
functional test
Gate length - maximum
Gate speed (varies with load) 3
Manual override
Life expectancy of electric motor
Duty cycle – mains present 4
12V DC
Battery-driven (standard capacity - 12V 5Ah)
1A @ 14.2V (charging voltage - 13.76V)
70mA
8A
18kgf
9kgf
250kg
20m
24m/min
Lockable with key release
20 (10 year life expectancy if operated only 10 times per day)
50%
Operations in standby with 5Ah battery
Half day 5
Collision sensing
• Positive Close Mode (e.g. to ensure activation of electric
fence contact switch)
• Multiple Modes of Operation with enhanced user interface
for exceptionally easy and versatile installation
Gate mass – maximum
Full day 5
• Selectable gate speed modes – Low Speed/High Speed
(High Speed is the default)
• Simple user interface makes changing setup child’s play
Operator push force - rated
D2 Turbo
90V– 240V AC ±10%, 50Hz
sliding gate
operators
D2 Turbo
Domestic Sliding Gate Operator
Operating temperature range
Onboard receiver type
Receiver code storage capacity
Receiver frequency
Degree of protection
Mass of unit packed (with standard kit,
but excluding rack and battery)
Packaging dimensions (with standard kit,
but excluding rack and battery)
1. Can operate off a solar supply, consult Centurion Systems for assistance
2. Can increase battery capacity for longer standby times
3. Gate operating speed can be configured to run at a slower, 16m/min ,
depending on the requirements of individual installations
30
15
Electronic
-15°C to +50°C
CENTURION code-hopping, multichannel output
32 transmitter buttons
433MHz
IP54
4.83kg
Width: 255mm x Depth: 188mm x Height: 333mm
4. Based on 25°C ambient temperature and unit not in direct sunlight; based
on an operator push force of less than 50% of rated
5. Based on 4m gate with no external accessories such as infrared Safety
Beams
TM
www.CentSys.com
Domestic
sliding gate
operator for
250kg gates
page 11
Technical Specifications
Domestic Sliding Gate Operator
Product Code: D2TSPCLD02
Technical Data
A low-voltage operator for domestic gates weighing up to 250kg, designed specifically for sites with no mains at the gate to reduce
installation costs while delivering outstanding reliability, comprehensive functionality and selectable high or standard speeds.
With the D2 Turbo Low-Voltage, there is no need for costly high-voltage cable runs and expensive isolators, simply use a lowvoltage step-down transformer or solar power supply.
Input voltage 1
D2 Turbo Low-Voltage
10V - 20V AC ±10%, 50Hz; 10V - 28V DC
Voltage output: 13.76V DC
Battery charger amperage output (dependent on
PSU input voltage)
10V AC input
400mA output
20V AC input
1A output
10V DC input
200mA output
28V DC input
Main Features
Motor voltage
Mechanical Features
• Multiple Modes of Operation: Standard Mode,
Open Only Mode, Reversing Mode, and two operator
Pre-flashing Modes
• Battery backup
• Turbo speed for greater security and convenience
• Automatic closing with adjustable time delay, and pushbutton
override
• Tough-as-nails steel pinion
• Very easy to install and set up, saving you time and money
Motor power supply 2
Current consumption (motor at rated load)
Operator push force - starting
Operator push force - rated
Gate mass – maximum
Gate length - maximum
Gate speed (varies with load) 3
• Lockable, easy manual override
• Remote gate-status indicator (gate position, power failure,
low battery, multiple collision detection and Pillar Light Status
indication)
• Stylish design enhances any entrance
• Pedestrian Opening
• Modular components clip together for easy maintenance
• Holiday Lockout
Electronic Features
• Courtesy/Pillar Light (fixed duration), with pre-delays and two
Pre-flashing Modes
Collision sensing
• Selectable gate speed modes – Low Speed/High Speed
(High Speed is the default)
Onboard receiver type
• Easy mounting with a revolutionary jacking system
• Low-voltage AC or DC input - perfect for installations where
there is no mains power at the gate
• Incredibly cost-effective solution
• High-security cleared beam Autoclose, in conjunction with
Safety Beams (PIRAC)
Duty cycle – mains present 4
Half day 5
• Onboard multichannel CENTURION code-hopping receiver with
the ability to learn remote control buttons to specific functions
(e.g. Gate Trigger, Pedestrian Opening, Holiday Lockout)
• Opening and Closing Safety Beam Inputs with beam circuit
functional test
Life expectancy of electric motor
Battery-driven (standard capacity - 12V 5Ah)
8A
18kgf
9kgf
250kg
20m
24m/min
Lockable with key release
20 (10 year life expectancy if operated only 10 times per day)
50%
Operations in standby with 5Ah battery
• Positive Close Mode (e.g. to ensure activation of electric fence
contact switch)
• Solar power-ready - energy-efficient, environmentally friendly
and offering greater autonomy
Manual override
1A output
12V DC
sliding gate
operators
D2 Turbo Low-Voltage
Full day 5
Operating temperature range
Receiver code storage capacity
Receiver frequency
Degree of protection
Mass of unit packed (with standard kit,
but excluding rack and battery)
Packaging dimensions (with standard kit,
but excluding rack and battery)
30
15
Electronic
-15°C to +50°C
CENTURION code-hopping, multichannel output
32 transmitter buttons
433MHz
IP54
4.83kg
Width: 255mm x Depth: 188mm x Height: 333mm
1. Can operate directly off a solar supply, consult Centurion Systems for
assistance
4. Based on 25°C ambient temperature and unit not in direct sunlight; based
on an operator push force of less than 50% of rated
2. Can increase battery capacity for longer standby times
5. Based on 4m gate with no external accessories such as infrared Safety
Beams
3. Gate operating speed can be configured to run at a slower, 16m/min ,
depending on the requirements of individual installations
TM
www.CentSys.com
Domestic
sliding gate
operator for
250kg gates
page 13
8
5
1
2
3
2
3
4
sliding gate
operators
8
7
6
1
9
Cabling Requirements
1.
D2 Turbo: 220V - 240V AC mains cable via double mains isolator switch (3 core LNE 1.5mm2 SWA)
D2 Turbo Low-Voltage: 10V - 20V AC or 10-28V DC cable via transformer in dwelling 1
Optional Wiring (all cable is multi-stranded):
+ 6 core
2.
Intercom, cable from control box to dwelling (n1
(n2 6 0.5mm² multi-stranded)
3.
Infrared Safety Beams (3 core 0.5mm² multi-stranded)
4.
Access control device (3 core 0.5mm² multi-stranded 4)
5.
Pedestrian keyswitch (2 core 0.5mm² multi-stranded) or
6.
Keypad (3 core 0.5mm² multi-stranded)
6
2
0.5mm² multi-stranded) or cable from control box to entry panel
7.
External radio receiver (3 core 0.5mm² multi-stranded 5)
8.
Pillar Lights (3 core LNE SWA 2, size according to power requirements)
9.
Inductive loop detector for free-exit (1 core 0.5mm² multi-stranded - silicone-coated 6)
1. Possibly increase cable thickness if Pillar Lights are to be installed
2. SWA - steel wire armoured. Type of cable must adhere to municipal bylaws and
preferably be screened. Screening provides better protection against lightning earth one end of the screening
5. For optimum range an external radio receiver can be mounted on the wall
6. Number of cores required by the intercom
310mm
3. Allows for all features such as Pedestrian Opening, Status LED, etc. to be
operated from the intercom handset inside the dwelling
4. Number of cores and type of cable could vary depending on the brand of access
control system being used
60mm
244mm
170mm
www.CentSys.com
page 15
Technical Specifications
Product Code: D5RB0000V6
Technical Data
The light-industrial D5-Evo is an evolution of the tried and tested D5, 500kg operator for domestic and light-industrial applications.
Potent push force, along with intelligent speed control and smooth opening and closing, makes the D5-Evo the automatic choice
for large private residences and townhouse complexes requiring reliable, feature-rich gate automation.
Battery charger amperage output (dependent on
PSU input voltage)
Motor power supply 2
Battery charger 1
Mechanical Features
• Local test button can be deactivated for added security
• Battery backup
• Sensitive anti-crushing protection for greater safety
Current consumption (motor at rated load)
• Integrated ChronoGuard timer functionality (a world first) –
Time-barring and Auto-activation features for switching on
Pillar Lights, deactivating ground loops, etc.
Operator push force - starting
• Lockable, easy manual override
• Custom-engineered gearbox molded from durable
engineering polymer
Electronic Features
• LCD interface – exceptionally easy setup with visual and
audible fault-finding and notification
• Advanced diagnostic screens indicating:
• Battery-low
• Battery charge level
• Fuse blown
• High current draw
• Details of the last transmitter activated
• Health of the drive electronics
• Currently activated gate inputs
• Multiple operating features including Intruder-detection Alarm
Modes (a world first)
• Onboard CENTURION code-hopping multichannel receiver
incorporating the following functionality:
90V - 240V AC ±10%, 50Hz
Current consumption (mains)
Motor voltage
Main Features
D5-Evo
Input voltage 1
Current consumption (mains)
170mA
90V AC input
1A output
240V AC input
2.2A output
12V DC
Battery-driven (standard capacity - 7Ah)
CP84SM - 2A @ 13.8V
170mA
10A
30kgf
Operator push force - rated
17kgf
Gate mass – maximum
500kg
Gate length - maximum
Gate speed (varies with load) 3
Manual override
sliding gate
operators
D5-Evo
Light-industrial Sliding Gate Operator
100m
18 - 22m/min
Thumbwheel behind locked door with key release
Maximum numbers of operations per day
150
Duty cycle – mains present 4
50%
Operations in standby with 7Ah battery
• Selective add and delete
• Onboard receiver can be disabled
• 500 transmitter button memory
Half day 5
Full day 5
Collision sensing
• Automatic maintenance features like Delete-Not-Present
• Opening and Closing Safety Beam Inputs
• Integrated Beam Test hardware to ensure the beams are
always working correctly
• See Diagnostics Made Easy for further details
Operating temperature range
Onboard receiver type
Receiver code storage capacity
Receiver frequency
44
35
Electronic
-15°C to +50°C
CENTURION code-hopping, multichannel output
500 transmitter buttons
433MHz
Degree of protection
IP54
Mass of unit packed (with standard kit,
but excluding rack and battery)
10kg
Packaging dimensions (with standard kit,
but excluding rack and battery)
1. Can operate off a solar supply, consult Centurion Systems for assistance
2. Can increase battery capacity for longer standby times
3. Gate operating speed can be configured to run slower, depending on the
requirements of individual installations
Width: 303mm x Depth: 231mm x Height: 432mm
4. Based on 25°C ambient temperature and unit not in direct sunlight; based
on an operator push force of less than 50% of rated
5. Based on 4m gate excluding infrared Safety Beams
TM
www.CentSys.com
light-industrial
sliding gate
operator for
500kg gates
page 17
Technical Specifications
Domestic Sliding Gate Operator
Product Code: D5RSPCLD06
Technical Data
This cost-effective sliding gate operator for gates weighing up to 500kg enables you to enjoy all the amazing features and
functionality of the flagship D5-Evo – even if you don’t have mains power at the gate.
All that is needed to breathe life into the feature-rich LCD controller is a low-voltage input, easily obtainable via a step-down
transformer, dramatically reducing installation costs.
Battery charger amperage output (dependent on
PSU input voltage)
Motor voltage
Motor power supply 2
Battery charger 1
Main Features
Current consumption (mains)
Mechanical Features
• Local test button can be deactivated for added security
• Save on cabling costs - no thick, expensive high-voltage
cables
• Sensitive anti-crushing protection for greater safety
• No need to fit costly isolators
• Battery backup
• Lockable, easy manual override
• Custom-engineered gearbox molded from durable
engineering polymer
Electronic Features
• LCD interface – exceptionally easy setup with visual and
audible diagnostics and notification
• Diagnostic screens indicating:
• Battery-low
Operator push force - starting
1A output
12V DC
Battery-driven (standard capacity - 7Ah)
CP84XTE - 1A @ 13.8V
170mA
10A
30kgf
17kgf
500kg
Manual override
Maximum numbers of operations per day
Duty cycle – mains present 4
100m
18 - 22m/min
Thumbwheel behind locked door with key release
55
20%
Operations in standby with 7Ah battery
Half day 5
Full day 5
• Selective add and delete
Collision sensing
• Onboard receiver can be disabled
Operating temperature range
Onboard receiver type
• 500 transmitter button memory
Receiver code storage capacity
• Automatic maintenance features like Delete-Not-Present
• Integrated Beam Test hardware to ensure that the beams are
always working correctly
400mA output
19V AC input
Gate mass – maximum
Gate speed (varies with load) 3
• Onboard CENTURION code-hopping multichannel receiver
incorporating the following functionality:
• Fuse blown
15V - 19V AC
15V AC input
Operator push force - rated
Gate length - maximum
• Multiple operating features including Intruder-detection Alarm
Modes (a world first)
• Opening and Closing Safety Beam Inputs
• High current draw
Current consumption (motor at rated load)
• Integrated ChronoGuard timer functionality (a world first) Time-barring and Auto-activation features for switching on
Pillar Lights, deactivation of ground loops, etc.
• Battery charge level
D5-Evo Low-Voltage
Input voltage 1
sliding gate
operators
D5-Evo Low-Voltage
Receiver frequency
100
95
75
www.CentSys.com
433MHz
10kg
3. Gate operating speed can be configured to run slower, depending on the
requirements of individual installations
• See Diagnostics Made Easy for further details
500 transmitter buttons
IP54
2. Can increase battery capacity for longer standby times
• Currently activated gate inputs
-15°C to +50°C
CENTURION code-hopping, multichannel output
Mass of unit packed (with standard kit,
but excluding rack and battery)
1. Can operate off a solar supply, consult Centurion Systems for assistance
• Health of the drive electronics
35
Electronic
Degree of protection
Packaging dimensions (with standard kit,
but excluding rack and battery)
• Details of the last transmitter activated
55
Width: 303mm x Depth: 231mm x Height: 432mm
4. Based on 25°C ambient temperature and unit not in direct sunlight; based
on an operator push force of less than 50% of rated
5. Based on 4m gate excluding infrared Safety Beams
domestic
sliding gate
operator for
500kg gates
page 19
25
8
5
1
2
3
2
3
4
sliding gate
operators
8
7
6
1
9
Cabling Requirements
1.
D5-Evo: 220V - 240V AC mains cable via double mains isolator switch (3 core LNE 1.5mm2 SWA)
D5-Evo Low-Voltage: 15V - 19V AC cable via transformer in dwelling 1
Optional Wiring (all cable is multi-stranded):
+ 6 core
2.
Intercom, cable from control box to dwelling (n1
(n2 6 0.5mm² multi-stranded)
3.
Infrared Safety Beams (3 core 0.5mm² multi-stranded)
4.
Access control device (3 core 0.5mm² multi-stranded 4)
5.
Pedestrian keyswitch (2 core 0.5mm² multi-stranded) or
6.
Keypad (3 core 0.5mm² multi-stranded)
6
2
0.5mm² multi-stranded) or cable from control box to entry panel
7.
External radio receiver (3 core 0.5mm² multi-stranded 5)
8.
Pillar Lights (3 core LNE SWA 2, size according to power requirements)
9.
Inductive loop detector for free-exit (1 core 0.5mm² multi-stranded - silicone-coated 6)
1. Possibly increase cable thickness if Pillar Lights are to be installed
2. SWA - steel wire armoured. Type of cable must adhere to municipal bylaws and
preferably be screened. Screening provides better protection against lightning earth one end of the screening
5. For optimum range an external radio receiver can be mounted on the wall
6. Number of cores required by the intercom
341mm
3. Allows for all features such as Pedestrian Opening, Status LED, etc. to be
operated from the intercom handset inside the dwelling
4. Number of cores and type of cable could vary depending on the brand of access
control system being used
60mm
250mm
160mm
www.CentSys.com
page 21
Technical Specifications
Product Code: D10RB000V3
Technical Data
Using CENTURION’s proven 24V DC technology, this is the complete solution for commercial and industrial gates weighing up to
1000kg. A rock-solid die-cast aluminium gearbox and reliable battery backup make the D10 ideally suited for complexes with large
gates and high traffic volumes, while an intelligent LCD controller with multiple Modes of Operation makes setup and diagnostics
veritable child’s play.
Input voltage 1
Motor voltage
Motor power supply 2
Battery charger 1
Current consumption (mains)
Current consumption (motor at rated load)
Main Features
Operator push force - starting
Operator push force - rated
Mechanical Features
• Battery backup
• Lockable, easy manual override with anti-jamming
• Strong die-cast aluminium gearbox
Electronic Features
• LCD interface – Exceptionally easy setup with visual and
audible diagnostics and notification
• Diagnostic screens indicating:
• Battery-low
Gate mass – maximum
• Intelligent speed control - high-speed for greater security and
convenience; slower speed for increased safety
• Integrated ChronoGuard time functionality (a world first) Time-barring and auto-activation features for switching on
Pillar Lights, deactivating ground loops, etc.
• Multiple operating features, including Intruder-detection
Alarm Modes (a world first)
• Onboard CENTURION code-hopping multichannel receiver
incorporating the following functionality:
Gate length - maximum
Gate speed (varies with load) 3
Manual override
D10
90V - 240V AC ±10%, 50Hz
24V DC
Battery-driven (standard capacity - 2 x 7Ah)
2A @ 27.5V
170mA
4A
40kgf
30kgf
1000kg
100m
22 - 26m/min
Lockable lever with key release
Maximum numbers of operations per day
750
Duty cycle – mains present 4
45%
Operations in standby with 5Ah battery
Half day 5
Full day 5
Collision sensing
Operating temperature range
Onboard receiver type
87
69
Electronic
-15°C to +50°C
CENTURION code-hopping, multichannel output
• Battery charge level
• Battery-low
• Fuse blown
• Selective add and delete
• High current draw
• Onboard receiver can be disabled
Degree of protection
IP54
• Details of the last transmitter activated
• 500 transmitter button memory
Mass of unit packed (with standard kit,
but excluding rack and battery)
13kg
• Health of the drive electronics
• Automatic maintenance features like Delete-Not-Present
Receiver code storage capacity
Receiver frequency
• Currently activated gate inputs
• Opening and Closing Safety Beam Inputs
• See Diagnostics Made Easy for further details
• Integrated Beam Test hardware to ensure that the beams are
always working correctly
• High duty cycle capability - for greater reliability in
high-volume applications
sliding gate
operators
D10
Industrial Sliding Gate Operator
Packaging dimensions (with standard kit,
but excluding rack and battery)
1. Can operate off a solar supply, consult Centurion Systems for assistance
2. Can increase battery capacity for longer standby times
3. Gate operating speed can be configured to run slower, depending on the
requirements of individual installations
500 transmitter buttons
433MHz
Width: 355mm x Depth: 288mm x Height: 485mm
4. Based on 25°C ambient temperature and unit not in direct sunlight; based
on an operator push force of less than 50% of rated
5. Based on 4m gate excluding infrared Safety Beams
TM
www.CentSys.com
industrial
sliding gate
operator for
1000kg gates
page 23
Technical Specifications
Product Code: D10TB000V1
Technical Data
CENTURION’s fastest operator yet! This is the ideal solution for extremely fast, feature-rich and high-security gate automation.
With a top speed of 50 metres per minute and all the amazing features that first made the D10 a favourite among installers and
end-users alike, the D10 Turbo offers the complete package of brains, brawn and expeditious speed.
D10 Turbo
Input voltage 1
90V - 240V AC ±10%, 50Hz
Motor voltage
Motor power supply 2
24V DC
Battery-driven (standard capacity - 2 x 7Ah)
Battery charger 1
2A @ 27.5V
Current consumption (mains)
Main Features
Mechanical Features
• Battery backup
• Lockable, easy manual override with anti-jamming
• Strong die-cast aluminium gearbox
• High duty cycle capability - for greater reliability in
high-volume applications
• Intelligent speed control - high-speed for greater security and
convenience; slower speed for increased safety
• Turbo speed for greater security and convenience
• LCD interface – exceptionally easy setup with visual and
audible diagnostics and notification
• Multiple operating features, including Intruder-detection
Alarm Modes (a world first)
• Diagnostic screens indicating:
• Onboard CENTURION code-hopping multichannel receiver
incorporating the following functionality:
• Battery-low
• Battery-low
• Fuse blown
• Selective add and delete
• High current draw
• Onboard receiver can be disabled
• Details of the last transmitter activated
• 500 transmitter button memory
• Health of the drive electronics
• Automatic maintenance features like Delete-Not-Present
• See Diagnostics Made Easy for further details
20kgf
Operator push force - rated
15kgf
Varies with speed
Gate mass – maximum 3
Gate length - maximum
50m
40 - 50m/min
Gate speed (varies with load) 4
Manual override
Lockable lever with key release
Maximum numbers of operations per day
750
Duty cycle – mains present 5
25%
Operations in standby with 5Ah battery
58
Half day 6
37
Full day 6
Collision sensing
Electronic
Operating temperature range
Onboard receiver type
-15°C to +50°C
CENTURION code-hopping, multichannel output
Receiver code storage capacity
• Battery charge level
• Currently activated gate inputs
8A
Operator push force - starting
• Integrated ChronoGuard time functionality (a world first) Time-barring and auto-activation features for switching on
Pillar Lights, deactivating ground loops, etc.
Electronic Features
170mA
Current consumption (motor at rated load)
sliding gate
operators
D10 Turbo
Industrial Sliding Gate Operator
500 transmitter buttons
Receiver frequency
433MHz
Degree of protection
IP54
Mass of unit packed (with standard kit,
but excluding rack and battery)
13kg
Packaging dimensions (with standard kit,
but excluding rack and battery)
Width: 355mm x Depth: 288mm x Height: 485mm
• Opening and Closing Safety Beam Inputs
1. Can operate off a solar supply, consult Centurion Systems for assistance
4. Varies with speed setting - see table
• Integrated Beam Test hardware to ensure that the beams are
always working correctly
2. Can increase battery capacity for longer standby times
5. Based on 25°C ambient temperature and unit not in direct sunlight; based
on an operator push force of less than 50% of rated
3. Gate operating speed can be configured to run slower, depending on the
requirements of individual installations
6. Based on 4m gate excluding infrared Safety Beams
Maximum Operating Speed for Corresponding Gate Mass
Gate Mass
TM
www.CentSys.com
Operator Maximum Running Speed
240kg
50m/min
300kg
42m/min
400kg
36m/min
500kg
32m/min
600kg
29m/min
700kg
27m/min
800kg
25m/min
900kg
24m/min
1000kg
23m/min
industrial
sliding gate
operator for
1000kg gates
page 25
8
8
5
1
2
2
3
4
sliding gate
operators
7
6
1
3
9
Cabling Requirements
1.
220V - 240V AC mains cable via double pole mains isolator switch (3 core LNE 1.5mm2
1
SWA
2
)
Optional Wiring (all cable is multi-stranded):
+ 6 core
0.5mm² multi-stranded) or cable from control box to entry panel
2.
Intercom, cable from control box to dwelling (n1
(n2 6 0.5mm² multi-stranded)
3.
Infrared Safety Beams (3 core 0.5mm² multi-stranded)
4.
Access control device (3 core 0.5mm² multi-stranded 4)
5.
Pedestrian keyswitch (2 core 0.5mm² multi-stranded) or
6.
Keypad (3 core 0.5mm² multi-stranded)
7.
External radio receiver (3 core 0.5mm² multi-stranded 5)
8.
Pillar Lights (3 core LNE SWA 2, size according to power requirements)
9.
Ground loop for free-exit (1 core 0.5mm² multi-stranded - silicone-coated 6)
6
1. Possibly increase cable thickness if Pillar Lights are to be installed
2. SWA - steel wire armoured. Type of cable must adhere to municipal bylaws and
preferably be screened. Screening provides better protection against lightning earth one end of the screening
4. Number of cores and type of cable could vary depending on the brand of access
control system being used
5. For optimum range an external radio receiver can be mounted on the wall
6. Number of cores required by the intercom
387mm
3. Allows for all features such as Pedestrian Opening, Status LED, etc. to be
operated from the intercom handset inside the dwelling
3
67mm
300mm
245mm
www.CentSys.com
page 27
A10 Endurance Product Code: A10RE000V4
A10 Heavyweight Product Code: A10RG0004
Technical Specifications
DC Converter: DC_CON10V2
Technical Data
Using a powerful three-phase motor, the A10 is the ultimate industrial automation solution. Since this beast is mains-powered,
it is able to provide an almost unlimited duty cycle with rapid opening and closing courtesy of a die-cast aluminium gearbox and
intelligent controller-inverter pairing.
A10 Endurance
220V - 240V AC ±10%, 50Hz (single phase)
Motor voltage
220V AC three-phase
Maximum absorbed current
Output pinion
6A
20 tooth mod 4
Gate speed at rated push force
Available Models
A10 Endurance:
A rapid and robust operator with a three-phase motor for commercial and industrial gates up to 1000kg
A10 Heavyweight:
An all-round performer for gates up to 2000kg
Standard speed
16m/min
13.6m.min
30m/min
NA
1000kg
2000kg
Maximum gate mass
Sprint speed
600kg
Maximum gate length
• High push force for reliable operation of almost any gate
• High duty cycle capability - for greater reliability in
high-volume applications
• Strong die-cast aluminium gearbox with anti-jamming
Sprint speed
• Proven lightning protection
• Pedestrian Opening input – prevents unauthorised vehicle
access
• Safety Beam input – connecting infrared Safety Beams
dramatically increases the safety of the automated system
Electronic Features
• Local and remote multi-function Gate Status LED
• Extremely rapid operating speed - up to 30 metres per
minute offers exceptional security and high-volume access
control
• Free-exit input (only opens gate)
• Multiple programmable features - to suit a wide variety of
applications
• Optional DC Converter for reliable battery backup with full
kit (DC_CONKITL):
• On-demand battery backup protection
NA
20m
Operator push force - rated
Standard speed
Mechanical Features
17 tooth mod 4
Lockable lever with key release
Sprint speed 2
Standard speed
Main Features
A10 Heavyweight
Input voltage 1
sliding gate
operators
A10
Industrial Sliding Gate Operator
Manual override
Duty cycle
• Selectable/adjustable Autoclose timer (1 - 255 seconds)
Electronic
Motor thermal protection
Electronic
Degree of protection
Onboard receiver
Mass of unit packed (with standard kit,
but excluding rack)
• Local diagnostic LEDs for easy programming diagnostics
Technical Data
Input voltage
Current draw @ rated thrust
Rated output voltage
• Battery-protection circuitry
Battery charger output 1
• Integrated battery charger
Duty cycle 2
Thermal protection
Degree of protection
Battery capacity 3
Operating cycles per Ah of capacity
Packaging dimensions
TM
80%
Anti-crushing sensing method
Packaging dimensions (with standard kit,
but excluding rack and receiver)
• Brown-out power failure detection
NA
Lockable lever with key release
-20°C to +50°C
• Override of Autoclose timer via trigger input
• 12V DC auxiliary supply connecting Safety Beams, external
receivers, keypads, etc.
35kgf
Operating temperature range
Optional battery backup
• Timed potential-free contact (e.g. Courtesy Lights)
30kgf
22.5kgf
IP54
√
Receiver not included
15kg
Width: 355mm x Depth: 288mm x Height: 485mm
DC Converter
12V DC
30A
310V DC
2A
20%
Electronic
IP65
Minimum 12V 7Ah but external 35Ah is recommended
Minimum 1 open or close cycle
Width: 269mm x Depth: 145mm x Height: 365mm
1. Can operate directly off a solar supply, consult Centurion Systems for
assistance
2. Based on 25°C ambient temperature and unit not in direct sunlight
3. Battery housed in separate enclosure
www.CentSys.com
INDUSTRIAL
sliding gate
operator for
HEAVY gates
page 29
8
8
5
1
3
1
2
4
sliding gate
operators
7
6
2
3
9
Cabling Requirements
1.
220V - 240V AC mains cable via double pole mains isolator switch (3 core LNE 1.5mm2
1
SWA
2
)
Optional Wiring (all cable is multi-stranded):
2.
Intercom cable from control box to dwelling (n1 6 + 6 core 2 0.5mm² multi-stranded) or cable from control box to entry panel
(n2 6 0.5mm² multi-stranded. Infrared Safety Beams (3 core 0.5mm² multi-stranded)
3.
Access control device (3 core 0.5mm² multi-stranded 4)
4.
Pedestrian keyswitch (2 core 0.5mm² multi-stranded) or
5.
Keypad (3 core 0.5mm² multi-stranded)
6.
External radio receiver (3 core 0.5mm² multi-stranded 5)
7.
Pillar Lights (3 core LNE SWA 2, size according to power requirements)
8.
Inductive loop detector for free-exit (1 core 0.5mm² multi-stranded - silicone-coated 6)
1. Possibly increase cable thickness if Pillar Lights are to be installed
2. SWA - steel wire armoured. Type of cable must adhere to municipal bylaws and
preferably be screened. Screening provides better protection against lightning earth one end of the screening
5. For optimum range an external radio receiver can be mounted on the wall
6. Number of cores required by the intercom
387mm
3. Allows for all features such as Pedestrian Opening, Status LED, etc. to be
operated from the intercom handset inside the dwelling
4. Number of cores and type of cable could vary depending on the brand of access
control system being used
67mm
300mm
245mm
www.CentSys.com
page 31
G. Backup Memory Module
Product Code: PCA12201V1.0
I
H. Wheel Kits
Product Code: CP52GSHXK3
J
L
N
D
Back up all the transmitters and operating details set up
in the controller.
O
I. Solar Supply
C
H
A. Steel, Nylon RAZ or Nylon Angle Rack
Product Code: CP20G, RAZKITSPCL, CP20N1
Product Code: ESOLAR20WA/ESOLAR40WA
J. G-SWITCH-22 GSM Device
Product Code: GSWITCH0V3
F
A
E
A variety of wheel kits are available from
Centurion Systems.
K
B
G
B
M
P
sliding gate
operators
Sliding Gate Operator Accessories
H
B
Alternative means of powering the system with a 20 Watt
or 40 Watt panel.
B. CENTURION Infrared Beams
Product Code: Photon wireless beams: PHOTON1V1; i5 wired beams: I5V3
K. SMARTGUARD or SMARTGUARDair
Keypad
Allows for monitoring and activating the operator, via
your phone, from anywhere in the world with GSM
coverage.
L. A10 DC Converter
Product Code: DC_CONKITL
Product Code: SK/1BLK, SK/AIRBLK
A variety of rack available in different lengths, for different
strengths.
C. P36 Passive Sensitive Edge
Product Code: 1010M52220
Passive sensitive edge provides additional protection against
crushing.
E. FLUX SA Loop Detector
Product Code: FLUXSA00V1
Allows free-exit of vehicles from the property (requires ground
loop to be fitted)
Always recommended on any gate automation installation to
increase the safety of the automated system.
D. Theft-resistant Cage
Product Code: 1195ACC001 / 113001V5PL / 11400101PL
Retro-installable steel cage that increases the resistance of
the operator against theft.
F. CENTURION Transmitter
Product Code: One-button: TX1NV2433; Two-button: TX2NV433;
Three-button: TX3NV2433; Four-button: TX4NV2433
Incorporates ultra-secure code-hopping technology.
Available in one-, two-, three- and four-button variants.
www.CentSys.com
Cost-effective and versatile wired or wireless keypad,
allowing access for pedestrians.
M. POLOphone Intercom
Product Code: POLOE2GOV3/POLOH00WV1
Allows visitors to communicate with people inside in order
to gain access to the property.
O. SOLO/LATTICE Proximity
Access Control
Provides battery backup and power failure autonomy for
the A10 operator.
N. Gooseneck
Product Code: XGSN-60000 or XSGN-6GLV0
Steel pole for mounting intercom gate station or access
control.
P. G-SPEAK Intercom
Product Code: GSC0K020V0,GSC1K020V0
Product Code: SOLO0001V1 / LATC0003V1
Proximity reader for allowing access for both pedestrians
and vehicles.
Mobile-based intercom system - answer your intercom
from anywhere in the world for maximum security and
convenience.
page 33
sliding gate
operators
Sliding Gate Operator Kits
D2 Turbo Full Kit
D2 Turbo Low-Voltage Full Kit
Product Code: D2TFULLKIT_RAZ1 / D2TFULLKIT_ NYLON1
Product Code: D2TSPCLD02_RAZ1 / D2TSPCLD02_ NYLON1
•
•
•
•
•
•
•
•
•
•
•
•
•
•
1 x Operator 1
1 x Foundation plate P
1 x Controller B
1 x Integral 1A charger J
1 x 5Ah battery N
4m x RAZ rack/Nylon angle rack S/U
2 x 4 button CENTURION transmitter
F
1 x Operator 1
1 x Foundation plate P
1 x Controller A
1 x Integral 1A charger J
1 x 5Ah battery N
4m x RAZ rack/Nylon angle rack S/U
2 x 4 button CENTURION transmitter
F
1
D2 Turbo/D2 Turbo
Low-Voltage
D5-Evo Full Kit
D5-Evo Low-Voltage Full Kit
Product Code: D5EVOFK_RAZ1 / D5EVOFK_STEEL2 / D5EVOFK_NYLON2
Product Code: D5RSPCLD06_RAZ1 / D5RSPCLD06_STEEL2 /
D5RSPCLD06_NYLON2
•
•
•
•
•
•
•
1 x Operator 2
1 x Foundation plate Q
1 x Controller C
1 x 2A charger K
1 x 7Ah Battery N
4m x RAZ rack/Steel rack/Nylon angle rack
2 x 4 button CENTURION transmitter F
D10 Full Kit
S/T/U
•
•
•
•
•
•
•
1 x Operator 2
1 x Foundation Plate Q
1 x Controller C
1 x 2A charger K
1 x 7Ah battery N
4m x RAZ rack/Steel rack/Nylon angle rack
2 x 4 button CENTURION transmitter F
1 x Operator 3
1 x Foundation Plate R
1 x Controller D
1 x 2A 24V charger K
2 x 7Ah Battery N
4m x Steel rack T
Product Code: D101T_FULL KIT
•
•
•
•
•
•
•
•
•
•
•
•
•
•
E
CP201 A10
Controller
1 x Operator 3
1 x Foundation Plate R
1 x Controller D
1 x 2A 24V charger K
2 x 7Ah Battery N
4m x Steel rack T
2 x Sets i5 Safety Beams G
2m x Passive sensitive edge
D10 Turbo Partial Kit
A10 Endurance Kit
Product Code: D101T_PART KIT
Product Code: A10ER
•
•
•
•
•
•
•
•
•
•
•
•
1 x Operator (20T Pinion)
1 x Foundation Plate R
1 x CP201 Controller E
1 x CP200 Inverter M
4m x Steel rack T
B
D2 Turbo
Controller
3
D10/D10 Turbo
C
D5-Evo
Controller
4
A10
D
D10
Controller
S/T/U
D10 Turbo Full Kit
Product Code: D101R
1 x Operator 3
1 x Foundation Plate R
1 x Controller D
1 x 2A 24V Charger K
2 x 7Ah Battery M
2 x Sets i5 Safety Beams G
2m x Passive sensitive edge
A
D2 Turbo Low-Voltage
Controller
2
D5-Evo/D5-Evo
Low-Voltage
I
CENTURION
Receiver
F
CENTURION
Transmitter
J
800mA Charger
G
i5
Infrared Beams
K
2A Switch Mode
Charger
H
Passive Sensitive
Edge
L
2A 24V
Charger
H
M
CP200
Inverter
N
5Ah
Battery
O
7Ah
Battery
P
D2 Turbo/D2 Turbo
Low-Voltage
Foundation Plate
4
Q
D5-Evo/D5-Evo
Low-Voltage
Foundation Plate
H
A10 Heavyweight Kit
R
D10/D10 Turbo/A10
Foundation Plate
S
RAZ Rack
T
Steel Rack
Product Code: A10GR
•
•
•
•
•
1 x Operator (17T Pinion)
1 x Foundation Plate R
1 x CP201 controller E
1 x CP200 Inverter M
4m x Steel rack T
4
U
Nylon Angle Rack
www.CentSys.com
page 35
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement