DGA I980
OWNER’S
MANUAL
THE DGAI980 DGMax
Super Digital Spread Spectrum
provides the longest range,
the clearest sound
and the best privacy.
OF YOUR NEW PHONE
CONTROLS & FUNCTIONS
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
12.
13.
14.
15.
36
35
19
34
33
32
31
30
29
page/int'com
20
digital answering machine
MIC
21 22 23 24
28
27
26
25
Slo
Bat
He
Tal
✱(
Me
Int
Set
De
Ch
Ha
Sel
Cal
ot Cover
ttery Compartment
eadset Jack
/Redial Key
lk Key
(Tone) Key
emory Key
tercom key
tup/Pause Key
elete Key
harging Contacts
andset Microphone
lect Key
ll ID Key
/Flash Key
16.
17.
18.
19.
20.
21.
22.
23.
24.
25.
26.
27.
28.
29.
30.
Volume ▲ and ▼ Key
Display
Handset Antenna
Handset Retainer Clip
Charging Contacts
PIN Key
Clock Key
Answer Key
Page/Int’com Key
Repeat Key
Ogm Key
Memo
Skip Key
Delete Key
Play/Stop Key
31.
32.
33.
34.
35.
36.
37.
38.
39.
40.
41.
42.
43.
44.
45.
46.
47.
48.
Message Counter Display
Status LED
Volume Up and Down Keys
Speaker LED
Speaker Button
Speaker
Ring Time Switch
Desktop/Wall Mount Adapter
Rec Time Switch
Base Antenna
Belt Clip Holder
Base Microphone
Spare Battery Compartment
Reset Switch
Base Ringer Off-On Switch
Pulse-Tone Switch
10V DC Jack
Tel Line Jack
OF YOUR OWNERS MANUAL
CONTENTS
CONTENTS
Controls And Functions . . . . . . . . . . . . . . .inside front cover
Precautions
Important Safety Instructions . . . . . . . . . . . . . . . . . . . . . . . 2
Important Electrical Considerations . . . . . . . . . . . . . . . . . . . 3
Introduction
Welcome . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Included In Your Package . . . . . . . . . . . . . . . . . . . . . . . . . 6
Installing and Adjusting your Phone
Installation Considerations . . . . . . . . . . . . . . . . . . . . . . . . . 7
Desk/Tabletop Installation . . . . . . . . . . . . . . . . . . . . . . . . . 8
Wall Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Installing the Handset Battery Pack . . . . . . . . . . . . . . . . . 13
Charging the Battery Pack . . . . . . . . . . . . . . . . . . . . . . . . 14
Cleaning the Battery Contacts . . . . . . . . . . . . . . . . . . . . . . 15
Setting the Pulse/Tone Switch . . . . . . . . . . . . . . . . . . . . . 15
Adjusting the Volume Controls . . . . . . . . . . . . . . . . . . . . . 16
Installing the Beltclip . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Headset Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Automatic Digital Code Security . . . . . . . . . . . . . . . . . . . . 18
Using Your New Phone
Making and Receiving Calls . . . . . . . . . . . . . . . . . . . . . . . 19
Speakerphone . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .21
Tone . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Flash and Call Waiting . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Page . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Intercom . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
PABX Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Storing a Phone Number in Memory . . . . . . . . . . . . . . . . . 24
Travelling Out-Of-Range . . . . . . . . . . . . . . . . . . . . . . . . . 24
Editing a Number In Memory . . . . . . . . . . . . . . . . . . . . . . 26
Dialing a Number In Memory . . . . . . . . . . . . . . . . . . . . . . 29
Chain Dialing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
Using Caller ID . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
The Integrated Answering Device
Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
Turning the Answering System On and Off . . . . . . . . . . . . 37
Setting the Clock . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
Recording Your Outgoing Message . . . . . . . . . . . . . . . . . 39
Selecting the Message Time . . . . . . . . . . . . . . . . . . . . . . . 40
Recording a Memo . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40
Selecting a PIN Code . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
Playing Your Messages . . . . . . . . . . . . . . . . . . . . . . . . . . 42
Repeating a Message . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42
Skipping a Message . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
Deleting a Message . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
Using the Reset Button . . . . . . . . . . . . . . . . . . . . . . . . . . 44
Remote Room Monitor . . . . . . . . . . . . . . . . . . . . . . . . . . . 44
Remote Access Away from Home . . . . . . . . . . . . . . . . . . . 45
Troubleshooting
Quick Reference Chart . . . . . . . . . . . . . . . . . . . . . . . . . . . 47
Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48
Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49
2
FOR YOUR PHONE
PRECAUTIONS
IMPORTANT SAFETY INSTRUCTIONS
When using your telephone equipment, these basic safety precautions should
always be followed to reduce the risk of fire, electrical shock, and injury to persons:
1. Read and understand all instructions.
2. Follow all warnings and instructions marked on the product.
3. Unplug this product from the wall outlet before cleaning, and use a dry
cloth, without liquid or aerosol cleaners.
4. Do not use this product near water; for example, near a bathtub, washbowl,
kitchen sink or laundry tub, in a wet basement or near a swimming pool.
5. Do not place this product on an unstable cart, stand or table. The telephone
may fall, causing serious damage to the unit.
6. This product should be operated only from the type of power source
indicated on the marking label. If you are not sure of the type of power
supply to your home, consult your dealer or local power company.
7. Do not allow anything to rest on the power cord. Do not locate this product
where the cord will be damaged by persons walking on it.
8. Do not overload wall outlets and extension cords, as this can result in the
risk of fire or electrical shock.
9. Never push objects of any kind into this product through cabinet slots, as
they may touch dangerous voltage points or short out parts that could result
in a risk of fire or electric shock. These slots and openings are provided for
ventilation. Never spill liquid of any kind on the product.
10. To reduce the risk of electric shock, do not disassemble this product. Take it to
qualified service personnel when service or repair work is required. Opening or
removing covers may expose you to dangerous voltages or other risks. Incorrect
reassembly can cause electric shock when the appliance is subsequently used.
11. Unplug this product from the wall outlet and refer servicing to qualified
service personnel under the following conditions:
A. If the power supply cord is damaged or frayed.
B. If liquid has been spilled into the product.
C. If the product has been exposed to rain or water.
D. If the product does not operate normally when following the operating
instructions. (Adjust only those controls that are covered by the operating
instructions. Improper adjustment of other controls may result in damage,
and will often require extensive repair work by a qualified technician).
PRECAUTIONS
E. If the product has been dropped, or the cabinet has been damaged.
F. If the product exhibits a distinct change in performance.
12. Do not use the telephone to report a gas leak in the vicinity of the leak.
Battery Safety Precautions
To reduce the risk of fire or injury to persons by the
battery, read and follow these instructions.
1. Use only the appropriate type and size battery pack specified in the owner’s
manual.
2. Do not dispose of the battery pack in a fire. The cell may explode.
3. Do not open or mutilate the battery pack. Released electrolyte is corrosive
and may cause damage to the eyes or skin. It may be toxic if swallowed.
4. Exercise care in handling the battery in order not to short the battery with
conducting materials such as rings, bracelets and keys.
5. Charge the battery pack provided with or identified for use with this product
only in accordance with the instructions and limitations.
6. Observe proper polarity orientation between the battery pack and battery
charger.
Warning!
UNIDEN AUSTRALIA Pty. Ltd. DOES NOT represent this unit to be waterproof.
To reduce risk of fire, electrical shock or damage to the unit, DO NOT expose this
unit to rain or moisture.
The exclamation point within an equilateral triangle is
intended to alert the user of the presence of important
operating and maintenance (servicing) instructions in the
literature accompanying the appliance.
IMPORTANT ELECTRICAL CONSIDERATIONS
Unplug all electrical appliances when you know an electrical storm is
approaching. Lighting can pass through your household wiring and damage any
device connected to it. This phone is no exception.
Please do not attempt to unplug any
appliance during an electrical storm.
3
Range
Your new phone is designed to achieve the maximum possible range by
transmitting and receiving according to the highest specifications. We have rated
this phone to operate at a maximum distance with the qualification that the
range depends upon the environment in which the telephone is used. Many
factors limit range, and it would be impossible to include all the variables in our
rating. The Maximum Range rating of this phone is meant to be used as a
means of comparison against other range claims.
Telephone Line Problems
If you are having trouble with your telephone service, you must first disconnect
your phone to determine if it is the cause of your problem. If you determine that it
is the cause, you must leave it disconnected until the trouble has been corrected.
Under power failure, this telephone may not operate. Please
ensure that a separate phone, not dependent on local power
is available during emergencies.
Radio Interference
Radio interference may occasionally cause buzzing and humming in your
cordless handset, or clicking noises in the base. This interference is caused by
external sources such as TV, refrigerator, vacuum cleaner, fluorescent lighting or
electrical storm. Your unit is NOT DEFECTIVE. If these noises continue and are
too distracting, please check around your home to see what appliances may be
causing the problem. In addition, we recommend that the base not be plugged
into a circuit that also powers a major appliance because of the potential for
interference. Be certain that the antenna on the unit is raised vertically.
In the unlikely event that you consistently hear distracting transmissions on
your phone, you may be receiving radio signals from another cordless telephone
or other source of interference.
Finally, it should be noted that some cordless telephones operate at frequencies
that may cause interference to nearby TV’s or VCR’s. To minimise or prevent such
interference, the base of the cordless telephone should not be placed near or on
top of a TV or VCR. If interference is experienced, moving the cordless telephone
farther away from the TV or VCR will often reduce or eliminate the interference.
4
More Than One Phone
Each telephone device that you connect draws power from the phone line. We refer
to the power drawn as the device’s Ringer Equivalence Number (REN). The REN is
shown at the bottom part of your telephone. If you are using more than one
phone or other device on the line, add up all the RENs. If the total is more than 3,
your phones might not ring.
WELCOME
TO YOUR NEW PHONE
INTRODUCTION
Congratulations on your purchase of the Uniden DGAI980 cordless telephone.
This phone is designed for reliability, long life, and outstanding performance
utilising the latest in 900 MHz Spread Spectrum Technology.
FEATURES
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
900 MHz Spread Spectrum Technology
Integrated Telephone Answering Device (ITAD)
Caller ID
Caller ID on Call Waiting
50 Number Caller ID Memory
Any key Answer
Speakerphone
Back-up Power Supply with Optional Battery Pack
3-Line, 16 Character LCD Handset Display
Headset Compatible
Handset Earpiece, Base Speaker and Ringer Volume Control
15 Channel AutoScan
10 Enhanced Memory Dial Locations
32 Digit Redial
2-way Page/Intercom
Hearing Aid Compatible
Redial, Flash, and Pause
Pulse/Tone Dialing
7-Day Standby Battery Time
4-Hour Talk Time
Digital Spread Spectrum Technology utilises a digital transmission
and a “wider frequency band” vs. a “single narrow band” 30/39 Standard Analogue
transmission. The result is a more secure conversation with the clarity of digital
sound, extended range, and minimal interference from other cordless phones.
Random CodeTM digital security automatically selects one of over 65,000 codes
for the handset and base. This feature prevents unauthorised calls as a result of your
phone being activated by other equipment.
5
INCLUDED IN YOUR PACKAGE
To get the most from your
phone, please read this
owner’s manual thoroughly.
Be sure to complete and mail
the product registration form.
If any of these items are
missing or damaged, contact
your place of purchase.
me
mo
ry
setup
pau
se
delete
Handset
Base
BT-900
Rechargeable Battery
AAD 950U
AC Adaptor
Long Telephone
Cord/Plug
Desktop/Wall
Mount Adaptor
Beltclip
Wall Mounting Screws
●
●
●
6
int'
com
This Owner’s Manual
Registration Card
Quick Reference Guide and other printed materials
INSTALLATION CONSIDERATIONS
Selecting a Location
Before choosing a location for your new phone, here are some important
guidelines you should consider:
▼
●
●
●
INSTALLING
AND ADJUSTING YOUR PHONE
●
●
●
The location should be close to both
a phone jack and a power outlet.
Keep the base and handset away from
sources of electrical noise such as
motors and fluorescent lighting.
Be sure there is sufficient space to rotate
the base antenna fully vertical.
The base can be placed on a desk, tabletop or
mounted on a standard wall plate.
You should charge the battery in your handset for 15-20 hours
before connecting the phone line.
Most phone equipment available now uses modular jacks. Phone cords are
fitted with a molded plastic connector which plugs into this type of jack. If
you do not have a modular phone jack, contact your local telephone
company for information about their installation.
Connecting the Telephone Cords
Consider these safety guidelines before connecting the telephone cord.
▼
Caution!
●
●
●
Never install telephone wiring during a lightning storm.
Never touch uninsulated telephone wires or terminals unless the telephone
line has been disconnected.
Use caution when installing or modifying telephone lines.
7
DESK/TABLETOP INSTALLATION
Before connecting your
phone line, fully charge the
Nickel- Cadmium battery
pack for 15-20 hours.
DC IN 10V
PULSE-TONE
TEL LINE
RESET
RINGER
OFF-ON
AC
Adapter
Line in
From
Telephone
Jack
1. Snap the desktop/wall mount
adaptor into the top of the base
as shown.
2. Plug the AC adaptor cord into the 10V
DC input jack on the back of the base.
3. Wrap the AC adaptor cord around the strain relief notch.
Place the power cord so
that it does not create a trip
hazard or where it could
become chafed and create a
fire or electrical hazard.
4. Plug the AC adaptor into a standard 240V AC wall outlet.
5. Charge the battery (See CHARGING THE BATTERY PACK,
page 15).
6. Plug one end of the telephone cord into the TEL LINE jack on the back
of the base.
7. Plug the other end of the cord into the
telephone jack on the wall.
Use only the Uniden AC
adaptor supplied with this
phone plugged to
uninterrupted power supply.
8
8. Set the base on a desk or tabletop with the
keypad facing up or down then place the
handset into the base. Raise the antenna to
a vertical position.
WALL INSTALLATION
▼
Standard wall plate mounting
This phone can be mounted on any standard wall plate.
Place the power cord so that
it does not create a trip
hazard or where it could
become chafed
and create a fire or electrical
hazard.
1. Snap the desktop/wall mount
adaptor into the bottom of the base
as shown.
2. Plug the AC adaptor cord into the 10V
DC input jack on the back of the base.
3. Place the AC adaptor cord inside the
molded wiring channel.
Wrap the cord around the strain
relief notch.
4. Plug the AC adaptor into a standard
240V AC wall outlet.
INSTALLATION & ADJUSTING
Use only the Uniden AC
adaptor supplied with this
phone plugged to
uninterrupted power supply.
5. Plug one end of the short telephone
cord (not supplied) into the
TEL LINE jack on the back of
the base. Plug the other end
into a standard telephone jack.
9
6. Align the mounting slots on the
base with the mounting posts on the wall.
Push in and down until the phone is
firmly seated.
Before you plug the other
end of the telephone cord
into the modular jack on the
wall, charge the battery (See
CHARGING THE BATTERY
PACK, page 15).
7. On the base, pull the handset retainer out
of the slot. Rotate clockwise 180°.
8. Flip the retainer from front to back.
Slide it back into the slot so that the lip
of the retainer is up and the oval is down.
The retainer holds the handset in place.
▼
Direct wall mounting
If you don't have a standard wall plate, you can mount your phone directly to
the wall. Before doing this, consider the following:
●
●
●
10
Select a location away from electrical cables, pipes, or other items behind the
mounting location that could cause a hazard when inserting the screws into the
wall.
Mount your phone near a working phone jack to avoid excessive
cord lengths
Make sure the wall material is capable of supporting the weight of the base and
the handset.
1. Insert two mounting screws (with their
appropriate anchoring device) into the wall
100mm apart. Allow about 5mm between the
wall and screw heads for mounting the phone.
Be careful not to insert the
mounting screws
into possible electrical
hazards such as cables,
wiring, or pipes.
2. Snap the desktop/wall mount
adaptor into the bottom of the base
as shown.
3. Plug the AC adaptor cord into the
10V DC input jack on the back of
the base.
INSTALLATION & ADJUSTING
4. Put the AC adaptor cord inside the
molded wiring channel. Wrap it around
the strain relief notch. Plug the AC
adaptor into a standard 240V AC wall
outlet.
5. Plug one end of the telephone
cord into the TEL LINE jack
on the back of the base. Plug the other
end into a telephone jack.
11
6. Align the mounting slots on the
base with the mounting screws on
the wall. Push in and down until
the phone is firmly seated.
7. On the base, pull the handset retainer
out of the slot. Rotate clockwise 180°.
8. Flip the retainer from front to back.
Slide it back into the slot so that the lip
of the retainer is up and the oval is down.
The retainer holds the handset in place.
12
INSTALLING THE HANDSET BATTERY PACK
1. Press battery cover release.
Slide cover off.
Use only Uniden Battery
(model BT-900) supplied
with your phone.
2. Install the nickel-cadmium battery
with the label down.
3. Slide the battery cover forward
until it snaps into place
INSTALLATION & ADJUSTING
13
CHARGING THE BATTERY PACK
▼
Initial battery charging
Before connecting your phone for the first time, fully
charge the rechargeable battery pack for 15-20 hours
without interruption.
1. Place the handset on the base.
2. Make sure that status LED lights.
If the LED doesn’t light, be sure the AC
adaptor is plugged in and the handset
makes good contact with the base
charging contacts.
▼
Charging optional battery pack
The base of your phone is equipped with a compartment for charging an extra
battery pack for use in your handset. You can obtain an extra battery
pack from your authorised Uniden dealer.
Please visit your authorised
Uniden dealer to obtain an
extra battery pack.
1. Position the battery pack so the contacts are faced up.
2. Slide the battery pack into
the charging compartment until it
locks into place. The compartment
has a latch that keeps the battery
in place.
3. Fully charge the battery for 24 hours. When charging is complete, lift the latch
to remove the battery pack. To install the charged battery into the handset, see
INSTALLING THE HANDSET BATTERY PACK, page 14.
In the event of a power failure, your spare battery pack
temporarily provides power for the base to enable user to make
and receive calls. The answering machine, speakerphone and
intercom will be disabled at this condition.
14
▼
Low battery indicator
When the battery pack is very low and
low battery
needs to be charged, the DGAI980 is
programmed to eliminate some functions to
save power. If the phone is not in use, the low battery flashes. If the
phone is in use, low battery flashes and the handset beeps.
All rechargeable nickel-cadmium batteries
develop a “memory effect”. The memory effect
gradually reduces your talk and standby time.
▼
To avoid Memory Effect
On a monthly basis, use the phone until the low battery indicator flashes
on the handset. Then charge the battery for 15-20 hours.
With normal usage, your battery should last about one year.
To maintain a good charge, clean all charging contacts on the handset and base
about once a month. Use a pencil eraser or other contact cleaner. DO NOT use
liquids or solvents; you may damage your phone.
SETTING THE PULSE/TONE SWITCH
Most phone systems use tone
dialing. Check with your
local phone company if
you’re not sure whether
your system is tone or pulse.
Be sure the PULSE/TONE switch
is in the TONE position, unless your local
phone system uses pulse dialing.
15
INSTALLATION & ADJUSTING
CLEANING THE BATTERY CONTACTS
ADJUSTING THE VOLUME CONTROLS
▼
Handset ringer volume
Press the vol ▲ or ▼ key on the handset
to set the handset ringer volume. There are two
ringer volume settings; high and low.
To select the high volume setting,
press vol ▲. The following screen
displays:
To select the low volume setting,
press vol ▼. The following
screen displays:
▼
Ringer High
Ringer Low
Base ringer volume
The ringer switch on your DGAI980 allows
you to turn the ringer
OFF or ON.
▼
Handset earpiece volume
There are three volume settings for the handset earpiece; high, normal and low.
The handset earpiece volume can be adjusted only during a call.
To lower the volume, press vol ▼. To raise the volume, press vol ▲.
The handset displays <High>, <Normal> or <Low> indicating the
current volume setting.
▼
Base speaker volume
To control the speaker volume of the
base, press the ▲ or ▼ .
16
INSTALLING THE BELTCLIP
▼
To attach the beltclip
1. Remove the slot cover.
2. Insert the beltclip into the empty slot
and press down until it clicks.
▼
To remove the beltclip
1. Pull back on the release tab and
lift the beltclip up.
INSTALLATION & ADJUSTING
2. Replace the slot cover. You
can store either the beltclip
or slot cover on the bottom
of the base.
17
HEADSET INSTALLATION
Use only the Uniden HS910
headset specifically designed
for Spread Spectrum phones.
You may hear a buzz or
hum on other headsets.
Your phone may be used with an optional
headset, the Uniden HS910. To use this feature,
simply plug the headset plug into the headset
jack. Your phone is ready for hands-free
conversations.
If you are using an optional headset, you must still use
the handset keypad for phone operations.
AUTOMATIC DIGITAL CODE SECURITY
Keep the headset wire away
from handset and
base antennas.
To prevent other parties from making unauthorised calls on your phone line, a
digital code was added to the DGAI980. Your phone’s handset and base share this
code. This code is randomly set each time you place the handset in the base. If
the phone experiences a power failure, you must reset the digital security code by
placing the handset on the base.
▼
To reset the digital security code
1. Restore power to the base.
2. Place the handset on the base.
status LED must light up.
The digital security code is reset.
18
MAKING AND RECEIVING CALLS
▼
Basic phone operation
Handset On Base
Handset Off Base
Base Only
Fold out the front cover of
this owner’s manual to use
the CONTROLS AND
FUNCTIONS diagram for
reference.
To answer
a call
Pick up handset.
Press
talk.
Press
speaker.
1. Pick up the handset.
2. Press talk.
3. Listen for the dial
tone.
4. Dial the number.
USING
YOUR NEW PHONE
To make
a call
To hang up
To redial
1. Press talk.
2. Listen for the dial
tone.
3. Dial the number.
Press talk, or return the handset to the base
(AutoStandby).
1. Pick up the handset.
2. Press talk.
3. Listen for the dial
tone.
4. Press redial.
Press speaker.
1. Press talk.
2. Listen for the dial
tone.
3. Press redial.
Note:
If any key is pressed before redial, the last number dialed will not redial.
When using the DGAI980 on the base unit, an ACA
approved headset is required.
19
ANSWERING A CALL
1. The handset rings and the
following screen appears:
2. Press talk to answer. Screen shows:
After 2 seconds, timer starts counting
AutoStandby automatically hangs up
when you place the handset
on the base.
Incoming Call
Talk 0:00
<Normal>
Talk
0:02
3. When you finish the call, press talk on
the handset, or return the handset
to the base.
Note:
If the user has subscribed to a Caller ID Display Service, Screen displays the following
while ringing:
• When Name Tagging is disabled
21/12 12:30PM 03
or the incoming Caller ID does not
match the one in the memory
02-9599-3577
- OR • When Name Tagging is enabled
- OR • When Caller ID signal is not strong
enough to display the complete ID
- OR • When Caller ID is coming from
overseas
- OR • When the Caller ID is from a
mobile phone
- OR -
20
21/12 12:30PM 03
Uniden
02-9599-3577
21/12 12:30PM 03
Uni❚ en
02-95❚ ❚ -3577
21/12 12:30PM 03
Unknown Number
21/12 12:30PM 03
04xx-xxx-xxx
• the Caller ID is coming from a
payphone
- OR • When Caller ID is coming from
- an analogue network exchange
- a silent number subscriber
- a caller who chooses to block their
number
PAYPHONE
Unavailable
21/12 12:30PM 03
Private Number
MAKING A CALL
▼ In
Use Dialing (Off-Hook Dialing)
1. Pick up the handset.
2. Press talk to answer.
3. Dial the number on the keypad, or
use one of the memory features.
(See USING MEMORY DIALING, page 29).
4. When you finish the call, press talk, or return the handset to the base.
▼ Standby
1.
2.
3.
4.
Dialing (On-Hook Dialing)
Pick up the handset.
Dial the number on the keypad.
Press talk.
When you finish the call, press talk, or return the handset to the base.
USING THE SPEAKERPHONE
To answer an incoming call or to put a current
call on hands free speaker phone conversation,
simply press speaker button. To hang up,
press speaker again.
30cm
21
USING YOUR PHONE
The base microphone is located
under the phone. Position yourself
approximately 30cm away from
the base and speak clearly.
TONE
The tone feature applies only
when the base is set to pulse.
If you are dialing in the pulse mode
and need to enter tone digits, press ✱ then
enter the digits. Once the call has ended, tone
mode is cancelled and pulse dialing resumes.
FLASH AND CALL WAITING
The flash + 2 procedure
toggles between the incoming
and original call (vice versa).
The flash + 1 procedure
will drop the current call and
pick up the incoming call or
call on hold.
If you have Call Waiting service and a call
waiting tone sounds, press flash then 2
to accept the call. After a short pause you will
hear the new caller. To return to the
original caller, press flash then 1.
REDIAL
The redial key redials the last number dialed. The redialed number can be up
to 32 digits long.
To call the last number dialed
from the handset, press redial.
If any key is pressed before
redial the last number will
not redial.
PAGE
To locate the handset when it is off
the base, press page/int’com on the base.
The handset beeps for 60 seconds.
The following screen appears:
22
Paging
To stop paging:
Handset: Press talk twice.
Base: Press page/int’com again.
USING YOUR DGAI980 INTERCOM
▼ Paging
from the Base to the Handset
1. Press page/int’com on the base.
The handset beeps. (If no answer, press
page/int’com again to disconnect.)
2. To answer a page, press talk or
int’com on the handset.
Speak within 30cm of
the base microphone.
3. To turn off the intercom, press speaker
on the base, or talk on the handset.
▼ Paging
from the Handset to the Base
1. Press int’com on the handset.
(If no answer, press int’com
to disconnect.)
2. To answer a page at the base, press
speaker or page/int’com .
Speak within 30cm
of the base microphone.
23
USING YOUR PHONE
3. To turn off the intercom, press speaker on
the base or talk on the handset.
TRAVELLING OUT-OF-RANGE
As you begin to move too far from the base, you will first hear a clicking sound.
As you travel further, the noise increases. If you travel out-of-range, your call
terminates.
PABX CONNECTION
Check with your PABX
supplier if you are not sure
whether your PABX network
uses Analogue or Digital
interface.
The DGAI980 telephone may work with a 2-wire Analogue PABX network.
However, with the DGAI980 hook-flash timing fixed at 90msec, some PABX
equipment that uses a different hook flash timing may have its special feature
(i.e. placing a call on hold or transferring a call) inaccessible.
STORING A PHONE NUMBER IN MEMORY
Your DGAI980 stores up to 10 name/numbers in the handset.
1. Remove the handset from the base.
2. Press and hold memory for
two seconds.
The following screen appears:
Memory Store
1
2
Whenever you are using a
menu screen, you must press
a key within 20 seconds or
the phone will return to
Standby. You may also press
memory to quit a memory
menu at any time.
3. Use the ▲ and ▼ keys or number
keypad to choose a memory location to store
a name/number.
4. Press select.
The following screen appears:
24
Store Name
5. Enter a name by using the ▲ and ▼
to scroll through the character menu.
The pause button counts as
one digit. Pressing
setup/pause more
than once increases the
length of pause in between
numbers.
keys
Use the and keys right or left, or to
create a blank space.
6. When you have finished entering a
name, press select.
The following screen appears.
The cursor flashes indicating
that the display is ready for a number.
to be entered.
7. Enter the phone number using the number keypad.
Store Number
If a pause is needed during dialling to access a long
distance service, press setup/pause to insert a pause.
The display shows a P.
8. When you have finished entering
a number, press select.
The handset beeps and and displays
a confirmation screen.
Memory 1 Stored
MAKE SURE you include the area code together
with the phone number you are keying into the
phone’s memory. This will be most useful for
Name Tagging feature.
USING YOUR PHONE
25
EDITING DETAILS IN THE MEMORY
▼ Editing
name/numbers stored in the Memory
1. Remove the handset from the base.
Whenever you are using a
menu screen, you must press
a key within 20 seconds or
the phone will return to
Standby. You may also press
memory to exit a memory
menu at any time.
2. Press and hold memory for
two seconds.
The display shows the ”Memory Store”
screen and memory locations 1-2 and
details.
1
2
Memory Store
JOHN SMITH
UNIDEN
3. Use the ▲ and ▼ keys or number
keypad to select the memory location you
would like to edit.
If you select Go Back at
any time, no changes are
made and the handset shows
the Memory
Store screen.
4. Press select.
Display shows:
5. Press select again to enter the Edit
Memory mode.
The following screen appears.
A cursor flashes indicating that the
display is ready to edit the name.
6. Edit the name with the ▲ and ▼ keys.
Use the ▲ and ▼ keys to enter symbols.
Use the and
left and right.
7. Press select.
26
keys to move the cursor
Edit Memory 1
Delete Memory 1
Go Back
Store Name
JOHN SMITH
The following screen appears.
Store Number
8175551212
A cursor flashes indicating that the
display is ready for the number to
be edited.
8. Use delete to clear number/s
Enter the phone number using the number keypad.
9. Press select.
The handset beeps and displays the
confirmation screen.
Memory 1 Stored
10. The display then returns to the Memory
Store screen. You may select another
number to edit (return to step 3) or press
memory to return to Standby.
▼ Deleting/Adding
Details in the Memory
After erasing a number, you may add a new number to memory.
1. Remove the handset from the base
2. Press and hold memory for
two seconds.
The handset shows the Memory
Store screen with saved
name/numbers displayed.
1
2
Memory Store
JOHN SMITH
UNIDEN
27
USING YOUR PHONE
3. Use the ▲ and ▼ keys, or number
keypad, to select the memory location
you would like to delete.
4. Press select.
The following screen appears:
5. Use the ▼ key to move the cursor
to Delete Memory mode.
6. Press select.
7. Use the ▲ key to move the
cursor to Yes.
Edit Memory 1
Delete Memory 1
Go Back
Delete Memory 1?
Yes
No
Delete Memory 1?
Yes
No
8. Press select.
There is confirmation tone.
The following screen appears:
9. The display then returns to the
Memory Store screen. You may select
another number to delete (return to
step 3) or you may press memory
to return to Standby.
28
Memory 1 Deleted
DIALING A NUMBER FROM THE MEMORY
To dial a number from the programmed memory location:
1. Press memory.
The handset displays your programmed
memory locations.
1
2
3
JOHN SMITH
2. Use the ▲ and ▼ keys to select the
memory location you would like to dial.
3. Press talk. The number dials
automatically.
CHAIN DIALING
Chain dialing is best used where the number to be dialed cannot fit in one
memory location, such as those using international access codes or those which
includes your account numbers.
1. Store the access codes or account numbers into a memory location and the rest
of the numbers into another memory location (see page 24 for storing numbers
into memory).
3. After a few seconds or when prompted, press mem, followed by memory
location (1-10) of the remaining numbers.
29
USING YOUR PHONE
2. To Dial: Press talk, then mem followed by the memory location (1-10) of the
access code or party/main number.
USING CALLER ID
To make use of this feature, you must subscribe to a Caller ID
Service from your telephone service provider.
▼ Caller
ID Features
While in stand-by mode, pressing set-up will allow changes to be made in the
AutoTalk, Caller ID on Call Waiting, Hyphen Display and Name Tagging features.
These features are initially set to ON status on your DGAI980.
•
AutoTalk allows you to answer the call simply by lifting the handset
from the base (without pressing talk).
•
Caller ID on Call Waiting (CIDCW) enables your phone to
display the Caller ID of the incoming call while currently using the phone.
This feature is currently not available in all areas of
Australia. Call your telephone service provider regarding
availability in your area.
Key in the area code together
with the phone number in
the memory.
30
•
Hyphen is an extra feature that enables number grouping of Caller ID
numbers for ease of reading.
•
Name Tagging enables the phone to display the caller’s name
(as programmed in the memory), if the incoming Caller ID matches the
number of and existing Memory Dial Data.
▼ To
change setting of any of the Caller ID Features
1. Press setup.
The following screen appears
1
2
3
Auto Talk:On
CIDCW
:On
Hyphen
:On
2. Use the ▲ and ▼ keys to move the
cursor to the selection that you would
like to change.
3. Once cursor is set to desired feature, press select to toggle setting between
ON and OFF.
4. After you finish your selections, press setup. Return the handset to the base.
▼ Screening
See Incoming Call display
Information on page 20.
your calls
Caller ID allows you to review caller
21/12 12:30PM 03
information before answering your
Uniden
phone. At the beginning of the second 02-9599-3577
ring, the display shows the date, time,
call count, name, and phone number of the caller. If your
Caller ID is not programmed on your phone’s memory or Name Tagging is
OFF, the name does not appear on the second line.
USING YOUR PHONE
31
▼ Reviewing
Caller ID name/numbers
To review your Caller ID name/numbers, follow the steps below:
1. Press call id.
The following screen appears:
New : 01
Total : 15
2. Press ▼ to scan through the
name/numbers.
The most recent name/number appears
first, with the date, time, call count,
name, and phone number. Press ▲ to
scan backwards.
3. Once you have reviewed your oldest
name/number, the following
screen appears.
21/12 12:30PM 03
Uniden
02-9599-3577
End
4. Press call id to return to Standby.
Once you have viewed all of your Caller ID name/
numbers and reach End, the message list does not cycle
back to the beginning. You must press ▲ to view your
previous name/numbers.
32
▼ Calling
a Caller ID name/number
1. Press call id.
The Caller ID summary screen shows
the number of new callers and total
number of calls.
New : 01
Total : 15
2. Press ▼ to scan forward. Press ▲
to scan backwards through the list.
3. Select the name/number that you
would like to dial.
21/12 12:30PM 03
Uniden
02-9599-3577
4. Press talk. The number
automatically dials.
USING YOUR PHONE
33
▼ Storing
a Caller ID name/number in a memory location
1. Press call id.
The Caller ID summary screen shows
the number of new calls and total
number of callers.
New : 01
Total : 15
3. Press ▲ or ▼ to find the name/
number that you would like to store.
4. Press memory to store the
selected name/number.
5. The Select Location screen appears.
Use the ▲ and ▼ keys to select a blank
memory location to store the new
name/number. (If you want to replace
an existing number with the Caller ID
name/number, skip to step 7.)
6. Press select. A confirmation tone
sounds. The number is programmed.
(To program name on the newly
programmed memory, follow steps on
Editing Details in the Memory on page 26.)
7. If you choose to replace an existing
number with the new Caller ID name/
number, press select. The following
screen appears:
1
2
Select Location
Bob Evans
UNIDEN
Replace Memory?
Yes
No
8. Use the ▲ key to move the cursor to Yes. Press select.
A confirmation tone sounds. The number is programmed.
34
▼ Deleting
a Caller ID name/number
To delete a single Caller ID name/number, follow the steps below.
1. Press call id.
The Caller ID summary screen shows
the number of new callers and total
number of calls.
2. Select the number that you would like to
delete. Press ▼ to scan forward through
the name/numbers and ▲ to
scan backwards.
New : 01
Total : 15
21/12 12:30PM 03
Uniden
02-9599-3577
3. Press delete.
The following screen appears:
If you select No, the Caller ID
screen returns.
Delete Message?
Yes
No
4. Press select or delete. A confirmation tone sounds. The Caller ID screen
returns with the next name/number displayed.
5. Press call id to return to Standby.
USING YOUR PHONE
35
▼ Deleting
all Caller ID name/numbers
To delete all of your Caller ID locations, follow the steps below:
1. Press call id.
The Caller ID summary screen shows
the number of new callers and total
number of calls.
New : 01
Total : 15
2. Press delete.
The following screen appears.
Delete All?
Yes
No
3. Use the ▲ key to move the cursor to Yes.
Press delete or select.
A confirmation tone sounds.
The following screen appears.
Total : 00
4. All your caller ID locations are deleted.
5. Press call id to return to Standby.
36
▼ Deleting
all Caller ID name/numbers
To delete all of your Caller ID locations, follow the steps below:
1. Press call id.
The Caller ID summary screen shows
the number of new callers and total
number of calls.
New : 01
Total : 15
2. Press delete.
The following screen appears.
Delete All?
Yes
No
3. Use the ▲ key to move the cursor to Yes.
Press delete or select.
A confirmation tone sounds.
The following screen appears.
Total : 00
4. All your caller ID locations are deleted.
5. Press call id to return to Standby.
37
THE INTEGRATED ANSWERING DEVICE
SETTING UP
THE INTEGRATED ANSWERING DEVICE
The DGAI980 has a built-in answering system to answer and record your incoming
calls. You can use your answering system to record a conversation, leave a memo
message for others who use the phone, or to answer the phone with your
personalised message when you are away.
FEATURES
●
●
●
●
Digital Tapeless Recording
15 minutes Recording Time
Call Screening
Selectable Outgoing Messages
●
●
●
Time and Day Stamp
Remote Access
Toll Saver
Digital Tapeless Recording allows you to quickly review, save, or delete messages.
You’ll never worry about a tape wearing out, jamming, or resetting improperly.
The Integrated Answering System is easy and convenient to use., However,
please read all instructions carefully before using your answering system.
TURNING THE ANSWERING SYSTEM ON/OFF
1. To turn the answering system on, press
answer. A tone sounds. An outgoing
message plays on the base speaker. A
second tone sounds after the message
plays. The message counter LED turns on
to indicate the unit is ready to answer calls.
2. To turn the answering system off, press
answer again. A tone sounds followed by
the announcement “Answer off”. The
message counter LED turns off.
Your answering machine system will automatically turn
on after 15 rings.
38
SETTING THE CLOCK
The clock on the DGAI980 Answering System starts when power
is applied to the base.
To set the correct time:
1. Press and hold clock until a tone sounds.
2. Press skip or repeat until the correct
day is announced. Numbers 0 through 6
display as each day is announced.
3. Press clock again to select the day.
The hour setting is announced.
4. Press skip or repeat until you hear the
current hour setting. Numbers 1 through 12
display as each hour is announced.
5. Press clock again to select the correct hour.
6. Press skip or repeat until you hear the
current minute setting.
The numbers 0 through 59 display as each
minute is announced.
7. Press clock again to select the correct minute.
The AM/PM setting is announced.
8. The LED displays an A or P. Press skip or
repeat until you hear the correct AM/PM setting.
9. Press clock again to complete your settings.
The DGAI980 announces the correct time.
39
SETTING UP ANSWERING DEVICE
RECORDING YOUR OUTGOING MESSAGE
When you receive a call, the answering system automatically plays either a
preset greeting, or your own personal greeting.
▼
Preset message
The following message is prerecorded:
“Hello, no one is available to take your call.
Please leave a message after the tone.”
▼
Recording your personal Greeting
1. Press and hold ogm until you hear a
long tone. After the message counter LED
blinks, release ogm. Record your message
by speaking within 30cm of the base
microphone.
2. When you finish recording your message,
press ogm again. A tone sounds. Your
message plays back for your review.
To choose between the pre-recorded greeting and your
personal greeting, press ogm during outgoing message
playback.
▼
Announce Only feature
The Announce Only feature repeats a prerecorded greeting - “No one is available
to take your call”, or your own personal greeting. It will not allow the caller to
leave a message.
For Announce Only, move the REC TIME
switch to the ANN position.
The message counter LED displays A when
the system is on Standby.
40
SELECTING THE MESSAGE TIME
▼
Incoming Message Recording Time
You can set your answering system to record
messages up to four minutes long.
To record up to one minute, move the
REC TIME switch to 1.
To record up to four minutes, move the
REC TIME switch to 4.
▼
Toll Saver
The ring time/toll saver switch sets your
answering system to answer after two or
four rings.
In the TS (Toll Saver) position, if you have
new messages, the answering system
answers after two rings. If there are no new messages, the system answers after
four rings. This way, when you call long distance to check your messages, and
have no messages, you can hang up after the second ring to save a charge.
The Memo function is
completely independent of
the outgoing message. It’s
handy for leaving other
family members quick
messages when you are
unavailable.
RECORDING A MEMO
The Memo function allows the user to record a message
on the base for others who use your phone.
1. Press and hold memo. A tone
sounds and the message counter LED
begins to blink.
2. Release memo. To record your message,
speak within 30cm of the base microphone.
3. When you have finished your message, press memo
to stop recording. The system returns to Standby.
A Memo is treated as a
incoming recorded message.
It will be added to your
stored messages.
41
To listen to your messages from a remote location, you will need to enter a twodigit Personal Identification Number (PIN) code (00-99).
To select a PIN:
1. Press and hold the pin button. A tone
sounds, and the LED displays 00.
2. To set the first number, press skip or
repeat to scroll from 0 to 9. When the
desired number appears in the display,
press pin again. This selects the first
number.
3. To set the second number, press skip or repeat to scroll from
0 to 9. When the desired number appears in the display, press pin. This selects
the second number. Your PIN is announced.
42
SETTING UP ANSWERING DEVICE
SELECTING A PIN CODE
PLAYING YOUR MESSAGES
To stop playing your
message at any time, press
play/stop again.
The base LED displays the total number of messages. If the display is blinking,
you have new messages. When the message centre is full,
the LED displays FL. The DGAI980 plays your new messages first.
After listening to your new messages, you may listen to your
old messages.
1. Press play/stop.
The system automatically
returns to Standby when all
messages have played.
The system announces the number of
new and old messages. After each
message is played, the time and day the
message was received is announced. The
message counter LED displays the
number of current messages.
USING
THE INTEGRATED ANSWERING DEVICE
2. When all new messages have played, a long tone is heard. The message counter
LED stops flashing to indicate all new messages have been reviewed.
43
3. After reviewing your new messages, you can review your old messages. Press
play/stop and follow the instructions above.
REPEATING A MESSAGE
1. Press play/stop to review your messages.
The number of old messages is announced.
2. After a message plays for a few seconds,
press repeat to replay the message.
Pressing repeat before 1-1/2 seconds of the message is played causes the system
to scan back one message. If you have several messages, press repeat until you
return to the message you want replayed.
3. You may press play/stop at any time to stop reviewing and return to
Standby. The message counter LED shows the total number of messages still
on the system.
SETTING UP ANSWERING DEVICE
SKIPPING A MESSAGE
1. Press play/stop to review your messages.
The number of messages is announced.
Each time skip is pressed,
the system scans forward
one message. If you have
several messages, press skip
to find the message you
want to display.
2. Press skip at anytime to skip to the
next message.
3. Press play/stop at any time to stop
reviewing your messages and return
to Standby.
The message counter LED shows the total
number of messages still on the system.
DELETING A MESSAGE
1. Press play/stop to review your messages .
When you press delete, you
are permanently deleting the
message. Once deleted, the
message cannot
be replayed.
2. If you decide to delete a message, while
listening to a message, press delete until
you hear a tone. The system beeps and
goes to the next message.
3. After you have played all of your messages,
a long tone sounds.
To delete all your messages, press and hold delete after reviewing
messages. When all messages are deleted, a tone sounds.
The answering machine will
not allow to delete ALL
messages unless all the
messages have been
reviewed.
The answering machine will answer “No remaining time” after 15
rings once the memory is full.
44
USING THE RESET BUTTON
The RESET button is used to initialise the
base computer.
The reset button can be used if an AC power
line disturbance causes the answering system
to malfunction and become inoperative.
Pressing RESET does not erase any data
stored in your system memory.
REMOTE ROOM MONITOR
You may call your answering system from any touch tone phone to monitor
sounds in the room where the base is installed.
1. Call your telephone number.
2. During the outgoing message playback, press # followed by your PIN code.
(See SELECTING A PIN CODE, page 41.)
3. Press # then while the system announces the time and date.
You will hear sounds in the room where your base unit is installed.
After 15 seconds, the answering system returns to the Command Waiting mode.
*
4. Press # then to monitor the room for another 15 seconds. Or, select another
remote function. Hang up to exit the system. The answering system
automatically returns to Standby.
*
45
REMOTE ACCESS AWAY FROM HOME
.
▼
You must enter a command
within 15 seconds of
entering Command Waiting
mode or the answering
system automatically hangs
up and returns to Standby.
Remote Switch On
In the event that you forgot to turn on your answering machine before you leave
home, you can switch it on from a remote location using a touch-tone phone.
1. Call your telephone number.
2. Wait for 15 rings.
3. The answering system announces the ogm.
4. Hang up. Your answering machine is ready to receive messages.
▼
Other Functions
You can access other functions such as checking recorded messages, playing or
deleting messages, etc. remotely using a touch-tone phone.
1. Call your telephone number.
The system will only
playback messages for four
minutes and then it returns
to Command Waiting mode.
To continue playing your
messages, press # then 2
again within 15 seconds.
2. While the outgoing message is playing, press # followed by your PIN code.
(For instructions to set your PIN code see page 41).
3. The answering system announces the time and day followed by the number of
messages in memory. Message playback automatically begins.
4. You may listen to your messages, or you may select a command from the
following chart:
FUNCTION
Repeat
Play
Skip
Delete
Stop
Answer On
Memo Record/Stop
Ogm Record/Stop
Answer Off
Monitor
PRESS
# then 1
# then 2
# then 3
# then 4
# then 5
# then 6
# then 7
# then 8
# then 9
# then
*
46
5. After all of your messages have played, intermittent beeps indicate that your
system is in Command Waiting mode. At this time, you may enter another
command from the chart above.
6. When you are finished, hang up to exit the system. The answering system
automatically returns to Standby.
47
YOUR NEW PHONE
TROUBLESHOOTING
QUICK REFERENCE CHART
If your phone is not performing to your expectations, please try these simple steps
before calling Uniden customer service.
SUGGESTION
PROBLEM
●
The charge light
won’t come on
when the handset
is placed in
the base.
●
●
●
The audio sounds
weak and/or
scratchy
●
●
●
Can’t make or
receive calls.
●
●
●
●
●
The handset
doesn’t ring or
receive a page.
●
Make sure the AC adaptor is plugged into the base and
wall outlet.
Make sure the handset is properly seated
in base.
Make sure the charging contacts on the handset and base
are clean.
Make sure that the base antenna is in a vertical position.
Move the handset and/or base to a different location away
from metal objects or appliances and try again.
Check both ends of the base telephone
line cord.
Make sure the AC adaptor is plugged into the base and
wall outlet.
Disconnect the AC adaptor for a few minutes, then
reconnect it.
Place the handset back on the charging cradle for a few
seconds. The status LED lights indicating that the
phone has been reset.
The Nickel-Cadmium battery pack may be weak. Charge
the battery on the base for 15-20 hours.
Be sure the antenna is in a vertical position.
The handset may be too far away from the base. Place the
base away from appliances or metal objects.
Place the handset back on the charging cradle for a few
seconds. The status LED lights indicating that the
phone has been reset.
48
SPECIFICATIONS
YOUR NEW PHONE
GENERAL
49
The DGAI980 complies with TS001, TS002, TS004, TS030, AS/NZS3260, AS/NZS3548
and FCC Part 15
(as per ACA Radio Communications Class Licensing Requirements).
Frequency control: PLL
Modulation: Direct Sequence Spread Spectrum; DBPSK
Operating temperature: 0º to +50º C
BASE UNIT
Frequency:
917.4 to 925.8 MHz (15 channels)
Power requirements: AC adaptor
AAD-950 U
10V 500mA
APVL # V99239
Size:
187mm (W) x 89mm (D) x 222mm (H)
Weight:
Approx. 770g (including optional battery)
Battery:
BT-900 (as a back-up)
Capacity
600mAH, 3.6V
Talk mode 2 hours
Standby mode 4 hours
HANDSET
Frequency: 917.4 to 925.8 MHz (15 channels)
Power requirements: Rechargeable Nickel-Cadmium battery pack
Size (without antenna): 57mm (W) x 44.5mm (D) x 184mm (H)
Weight: Approx. 265g (including battery)
Battery:
BT-900
Capacity
600 mAH, 3.6V
Talk mode
4 hours
Standby mode
7 days
Specifications, features, and availability of optional
accessories are all subject to change without prior notice.
WARRANTY
One-Year Limited Warranty
Important:
Evidence of original purchase is required for warranty service.
WARRANTOR:
Uniden Australia Pty Limited ACN 001 865 498
WARRANTY
FOR YOUR NEW PHONE
ELEMENTS OF WARRANTY: Uniden warrants to the original retail owner for the duration of
this warranty its DGAI980 DGMax (here in after referred to as the Product), to be free from
defects in materials and craftsmanship with only the limitations or exclusions set out below.
WARRANTY DURATION: This warranty to the original retail owner, shall be in effect only
for 12 months from the date of the original retail sale. This warranty will be deemed
invalid if the product is: (A) Damaged or not maintained as reasonable or necessary, (B)
Modified, altered or used as part of any conversion kits, subassemblies, or any
configurations not sold by Uniden, (C) Improperly installed, (D) Repaired by someone
other than an authorised Uniden Repair Agent for a defect or malfunction covered by this
warranty, (E) Used in conjunction with any equipment or parts or as a part of a system not
manufactured by Uniden.
PARTS COVERED: This warranty covers for one (1) year, the Base Unit and Handset only. All
accessories (AC Adaptor, Battery, Mount Adaptor, Belt Clip, etc.) are covered for 90 days only.
STATEMENT OF REMEDY: In the event that the product does not conform to this warranty at
any time while this warranty is in effect, the warrantor, at its discretion, will repair the defect
or replace the product and return it to you without charge for parts and service. THIS
WARRANTY DOES NOT COVER OR PROVIDE FOR THE REIMBURSEMENT OR PAYMENT OF
INCIDENTAL OR CONSEQUENTIAL DAMAGES. THIS GUARANTEE IS IN ADDITION TO AND
DOES NOT IN ANY WAY AFFECT YOUR RIGHTS UNDER THE CONSUMER GUARANTEE ACT.
WARRANTY CARD: If a Warranty Card has been included with this Product, please
complete and return to us within 14 days of purchase. Your name and the serial number of
the Product will then be registered in our database and this will help us process your claim
with greater speed and efficiency should you require warranty service.
PROCEDURE FOR OBTAINING PERFORMANCE OF WARRANTY: In the event that the
Product does not conform to this warranty, the Product should be shipped or delivered,
freight pre-paid, with evidence of original purchase (e.g. a copy of sales docket) to the
warrantor at:
UNIDEN AUSTRALIA PTY LIMITED
SERVICE DIVISION
345 Princes Highway, Rockdale, NSW 2216
Ph: (02) 9599 3577 Fax: (02) 9599 3278
FREE CALL 1800 632 789
Customers in other States should ship or deliver the Product freight pre-paid to their nearest
Uniden Authorised Repair Centre, (Contact Uniden for the nearest Warranty Agent to you).
50
At Uniden, we’ll take care of you!
If you need any assistance with this product, please call our Customer Hotline at
1800 632 789
FOR PURCHASING A UNIDEN PHONE!
THANK YOU
Uniden Australia Pty Limited
© 2000 Uniden Australia Pty Limited
Part Code UCZZ01667DZ
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement