ProK142 Manual
Pro-Kool® 42" Evaporative Cooler
USER'S MANUAL
Pro
This page intentionally left blank.
Table of Contents
INTRODUCTION ..................................................................................................................................................................1
Why use evaporative coolers in your work place?
How does evaporative cooling work?
ABOUT THIS MANUAL........................................................................................................................................................1
SAFETY INFORMATION ..................................................................................................................................................1-2
SAFETY RECOMMENDATIONS ..........................................................................................................................................2
SPECIFICATIONS ................................................................................................................................................................2
UNIT DESCRIPTION ..........................................................................................................................................................3
WATER SUPPLY SYSTEM ..................................................................................................................................................4
COOLING PAD ASSEMBLY ................................................................................................................................................4
CONTROL ............................................................................................................................................................................5
OPERATION AND MAINTENANCE ....................................................................................................................................7
Unit Placement and Other Considerations
Unpacking and Initial Setup
Regular Cleaning
Normal Startup
Normal Shutdown
TROUBLESHOOTING ..........................................................................................................................................................8
Cooling Pads not Wetting
Foaming
Line Clogs or Obstructions
Odor Control
Scale Buildup
Splattering Out Front
Leaking Out Bottom
OPTIONAL ACCESSORIES ................................................................................................................................................9
Pneumatic Wheel Option
Water Conditioner & Cleaner
REPLACEMENT PARTS............................................................................................................................................10 & 11
PERFORMANCE CHARTS ................................................................................................................................................12
HUMIDITY CHARTS ..........................................................................................................................................................13
GENERAL ..........................................................................................................................................................................14
WARRANTY........................................................................................................................................................................15
Introduction
WHY USE EVAPORATIVE COOLERS IN YOUR WORKPLACE?
•
The Pro-Kool® evaporative cooler requires little space, has a low initial cost, is inexpensive and simple to operate and requires
minimal scheduled maintenance.
•
Due to the design and construction of the cooling pads, cooling efficiency is normally maintained near optimum throughout the life
of the pads. (Approximately two seasons)
•
In many cases, evaporative coolers are a better solution than mechanical refrigeration systems because they are more economical
to operate and maintain and do not use environmentally sensitive and costly refrigerants.
HOW EVAPORATIVE COOLING WORKS
Evaporative cooling is the same process your body uses to cool itself. When you perspire, and air moves across your skin, a portion of the
perspiration (water) evaporates. Evaporation requires heat to change liquid water-to-water vapor and this heat is taken from your skin,
producing the cooling effect.
In an evaporative cooler, the cellulose cooling pads take the place of your skin, water instead of perspiration wets them and a fan moves the
air. The air blows across the cooling pads and evaporates moisture. Heat is drawn from the pads and the air, dropping the air temperature
and producing the cooling effect. The cooled air is then forced through a building or space and displaces the warm air out building openings,
cooling the surroundings. In addition, air velocity increases the cooling effect as it moves over the skin of people in the airflow path.
Pro-Kool® evaporative coolers are portable and use the latest technology to provide large volumes of cool air, efficiently and inexpensively for
cooling small to medium size areas. Simply adding more units can accommodate larger areas. With proper sizing and application, a Pro-Kool®
evaporative cooler can lower the effective air temperature by up to 20°. Even in high humidity, the efficiency of the Pro-Kool® evaporative
cooler provides effective cooling.
About this Manual
The intent of this manual is to help you in two ways: to provide you with step-by-step instructions for quick and easy assembly of your
product and to serve as a reference for simple maintenance and questions regarding your product.
Important! Read ALL instructions carefully before starting your Pro-Kool®.
• Optional equipment contains necessary instructions for assembly or operation.
Important! Pay particular attention to all SAFETY information.
All information, illustrations and specifications in this manual are based on the latest product information available at the time of printing.
We reserve the right to make changes at any time without notice.
Safety Information
Warning and Danger Decals have been placed on the equipment to warn of potentially dangerous situations. Care should be taken to
keep this information intact and easy to read at all times. Replace missing or damaged safety decals immediately.
Using the equipment for purposes other than specified in this manual may cause personal injury and/or damage to the equipment.
Safety-Alert Symbol
This is a safety-alert symbol. When you see this symbol on your equipment, be alert to the potential for personal injury. This
equipment is designed to be installed and operated as safely as possible… however, hazards do exist.
Signal words are used in conjunction with the safety-alert symbol to identify the severity of the warning.
CAUTION indicates an imminently hazardous situation, which, if not avoided, COULD cause damage to your equipment or equipment
failure.
WARNING indicates a potentially hazardous situation, which, if not avoided, COULD result in death or serious injury.
1
Safety Information
Follow Safety Instructions
Carefully read all safety messages in this manual and on your equipment safety decals. Follow recommended precautions and safe
operating practices.
Keep safety decals in good condition. Replace missing or damaged safety decals.
Decal Descriptions
This diagram shows the proper location of the safety decals as shipped from the factory. Replace damaged or missing decals. Make sure
the decals are easy to see at all times.
Safety Recommendations
READ AND SAVE THESE INSTRUCTIONS!
• This is an electric device with moving components. There is the possibility of fire, electric shock, or injury to persons. Ensure all the
safety recommendations are adhered to in order to minimize this risk.
• Disconnect all power and unplug the unit before you inspect, clean or perform maintenance on the components of the unit.
• Never reach into the unit when it is running; you could become entrapped by the v-belt or injured by the rotating fan blades.
• The frame edges may be sharp; do not run your hand along them. Be careful and wear gloves when you reach under the frame to
inspect the PVC pipes and mesh socks.
• A GFCI (Ground Fault Circuit Interrupter) is recommended for use with this product.
• If pads and grates are removed for servicing, they must be replaced prior to operating unit.
Pro-Kool Specifications
•
Length x Width x Height: 51" x 33" x 68"
•
Shipping Weight: 300 pounds
•
Fan Motor: 1 Hp, 115 volt, 2-speed, 60 Hz. (also available in 230V and 50/60 Hz), 12.4 amps, 12,480 cfm.
•
Pump - Little Giant 115 volt, 60 Hz., Submersible, 1200 GPH.
•
Reservoir Capacity: 38 Gallons
•
Optional Water Supply - Standard 3/4" hose connection (garden hose size)
•
Housing - High impact poly w/UV protection
•
Evaporation Media - Chemically treated cellulose paper to resist deterioration. 8" thick pads.
2
Pro-Kool Unit Description
The Pro-Kool® evaporative cooler is a completely self-contained, portable unit capable of delivering 15 MPH velocity of air with a temperature
drop of up to 20°. The unit is composed of:
•
•
•
•
Level-controlled water supply system
Cooling pad assembly
Motor-driven fan
Frame and housing
The bottom is made of high impact poly and holds approximately 40 gallons at normal operating level (about 6" deep).
A float-operated valve automatically maintains proper water level when the unit is connected to a water supply.
The bottom rests on, and is fixed to, a rugged steel support frame. Four casters (2 locking, 2 regular) are attached to the underside of the steel
frame.
A pump draws water from the bottom and discharges it through the vinyl hose to the PVC pipes located above the cooling pads. The PVC pipes
distribute water onto the top of the cooling pads; saturating them. Excess water drips back into the bottom through the holes in the cooling pad
support channels.
The cellulose cooling pads sit in support channels and are held in place by the tray and pad support plate.
The fan is powered by a belt drive 1hp electric motor. The fan draws room air through the cooling pads where it picks up moisture and cools
by evaporation. The fan blade then discharges the cooled air.
Note: It is important the cooled space has sufficient air openings so the warmer air can flow out and be replaced by the cooled air.
A closed-in space or high humidity will reduce the cooling effect. See Unit Placement and Other Considerations in the "Operations
and Maintenance" section of this manual.
Note: Water weighs about eight pounds per gallon, so when the unit is full, it weighs over 500 pounds. During setup and before
startup, place the unit in the desired location and then fill the bottom. Do not attempt to lift the unit once it is filled and be careful to
avoid spills when moving it; even over smooth ground. Do not try to push it over rough or soft ground as you can overstress the
wheels and frame and cause structural and component damage, which is not covered by warranty.
Water Supply System
Hose adapter
The water can be supplied continuously with an ordinary garden hose by attaching it to the supplied hose adapter to the fill connection, or it
can be filled manually.
With a continuous water supply connected, the float valve in the bottom rises and falls with the water level. A linkage attaches the float to the
shutoff valve in the fill connection. As the water level rises to normal operating level (about 5" deep), the float valve shuts off the water supply.
When the water level drops, the float valve reopens to maintain a normal operating level.
After unplugging the unit, the bottom can also be manually filled with a hose or bucket; if a hose connection is impractical. Simply remove
any of the pad sections and place the hose, or pour the water, directly into the bottom. When you fill the bottom manually it can be filled to a
higher level, but make sure someone monitors the filling operation to avoid overfilling and flooding.
Note: Water damage due to overfilling is not covered by the warranty.
Note: When you run the unit and manually fill it, check the water level frequently so it does not run dry. Operating the pump
without water will damage it or reduce its service life. This is not covered by the warranty. The cooling effect also stops if the pads
are dry.
Note: Pads must be replaced before operating unit.
3
Water Supply System
A drain in the bottom allows you to drain the unit for cleaning and
maintenance. A drain cap on the underside covers the drain during
operation. Make sure the cap is in place before filling.
The pump is attached to the fan housing. Plastic ties hold the pump in its
proper position.
The pump can be easily removed and replaced.
A small plastic screen covers the pump inlet to prevent foreign matter from
entering and damaging the pump impeller.
Note: A dirty water supply will quickly reduce the unit's performance
and the unit will require more frequent cleaning to maintain cooling
effectiveness. Always try to use a filtered, treated water supply.
A clear vinyl hose connects the pump to the valve. From the valve, a "T" connector supplies two lines that run along the top of the pads and
up to supply the PVC pipe with water. Each piece of vinyl hose connects to a PVC pipe, which run horizontally along the top of the inlet
above the cooling pads.
The PVC pipes have a series of holes that run the full length of the pipe. The holes direct the water inward at a 90° angle against a
deflector plate to continuously saturate the cooling pads from the top down. Excess water drains back to the bottom through drainage holes
in the bottom support channels which support the cooling pads.
Note: Water cleanliness has a major effect on the cooler's performance. Use a clean water supply and consider a water softener if
your water is hard. Dissolved solids in hard water deposit on the cooling pad surfaces and reduce the airflow through the unit and
therefore the amount of evaporation.
Cooling Pad Assembly
The cooling pads are critical for proper, efficient cooler operation. They are made of laminated cellulose (paper) fibers and arranged to give
a large surface area for evaporation and to provide a rigid structure. The shape of the cells allows high velocity airflow through the pad at a
minimum pressure drop. At the same time, the air passages between the cells force the incoming air to impinge on the wet cell surfaces and
maximize evaporation.
Note: The Pro-Kool® evaporative cooler also acts as an air filter and removes dust and other particles from the air. This dirt
collects on the cooling pads and lowers cooler efficiency. The pads should be cleaned at least weekly and more frequently in
dusty conditions. See Regular Cleaning under "Operation & Maintenance".
The pump supplies a continuous flow of water over the pads causing a "sheet flow" which constantly replaces the water lost to evaporation
and keeps the pads saturated.
One cubic foot of the cooling pad material holds about a gallon of water during operation. One cubic meter holds about 100 liters of water.
Note: The cooling pads are relatively strong but are subject to crushing, especially when wet. Handle them carefully when you
clean them. Crushed cells reduce the total airflow through the unit and therefore lowers it's cooling capacity.
The cooling pad sections, (four sections total), sit in plastic tray at the back and bottom of the unit. The tray holds the cooling pads in
position and form a back to completely enclose the unit.
Note: Do not remove or handle the cooling pads when they are wet, as they damage easily. Run the fan without the pump until
pads are dry. With normal care, the pads should last at least two seasons. Abuse or mishandling will reduce their effectiveness
and shorten their life.
4
Control
The Pro-Kool® PROK142-2 control switch is mounted on the front of the unit in the upper right corner.
It has the following positions:
OFF - Power is off to the blower motor and the pump motor.
LOW VENT - The fan runs at low speed and the pump is OFF.
HIGH VENT - The fan runs at high speed and the pump is OFF. Use this setting to quickly dry the
cooling pads for removal and cleaning.
LOW COOL - The fan runs at low speed and the pump is on. Use this setting for low cooling loads.
Pro-Kool® Control Switch
HIGH COOL - The blower runs at high speed and the pump is on. Use this setting for maximum
cooling.
PUMP ONLY - Pump is on and the fan is OFF. Use this setting to drain unit only.
Operation & Maintenance
Unit placement and other considerations
Pro-Kool
Pro-Kool
The Pro-Kool® unit(s) should be placed at one end of the
building and an appropriate exhaust fan should be at the
opposite end to pull the cool air from the Pro-Kool® unit and
discharge the warm air out of the building.
Try to get all the air flowing in the same direction. Do not direct
other fans against the Pro-Kool® unit. It will counter the
Pro-Kool®'s airflow and stop the cooling effect.
Obstructing the airflow from the Pro-Kool® unit severely
reduces the cooling effect.
Avoid using ceiling fans as they disrupt the airflow from the
Pro-Kool® unit.
Use as many exhaust fans as possible to create a natural draft
through the building. This will enhance the Pro-Kool®'s
performance.
Typical Pro-Kool® Unit Arrangement
5
Operation & Maintenance
UNPACKING AND INITIAL SETUP
The Pro-Kool® 1HP Evaporative Cooler is shipped upright on a pallet. The Pro-Kool® is fully assembled and ready for service except for
thoroughly cleaning manufacturing dust from the cooling pads before running it for the first time.
CAUTION: Be careful when you move the unit. Avoid jarring or dropping the unit to prevent damage to the bottom.
1.
Cut the straps that wrap the unit.
2.
Remove the shrink wrap.
3.
Ensure the switch is OFF and the unit remains unplugged.
4.
Remove the pad support plate from the back of the unit by removing all the set screws.
5.
Remove the cooling pads from the unit. Pull pad out and then lift out of drain rail. With one pad out, the rest can be easily removed in
the same manner.
6.
Inspect the entire unit for shipping damage.
7.
Ensure the fan belt is attached to the motor and fan
pulleys. To ensure it is correct, press your finger on the belt
about halfway between each pulley. It should have about a
half-inch of play. If it is too loose, the V-belt will slap around
while running. If it is too tight, it will cause the pulley bearings
to wear and fail prematurely.
Note: If you notice any damage to your unit, contact your
dealer immediately.
8.
Thoroughly clean all four cooling pad sections using a garden
hose.
Note: Do not use cleaning fluids or other chemicals to clean
the pads as they can cause foaming during operation. Use only
clean water. Refer to page 9 for approved cleaners.
Pro-Kool® assembly
6
9.
Remove the drain cap from the underside and rinse with a
hose to flush any manufacturing dust, etc. from the unit.
10.
Replace the drain cap.
11.
Replace the pads.
12.
Proceed to "Normal Setup".
Operation & Maintenance
REGULAR CLEANING
The frequency with which the Pro-Kool® is cleaned will depend on the environment in which it is used. The more dirty the environment the
more often it will need cleaning. In most cases the Pro-Kool® will need to be cleaned weekly.
Caution: The pads should be dry before you handle them, as they are stronger when dry than when they are wet and less
susceptible to damage. If they are wet, run the unit in the HIGH VENT position until they are dry. After cleaning, let the pads air
dry before you replace them.
1.
2.
3.
4.
5.
6.
Turn the switch to OFF and unplug the unit.
Check the pads for cleanliness. If they are dirty, remove and clean by spraying with a garden hose, water only. If they are not dirty you
will still need to remove the cooling pads to clean the inside of the unit. Dirty cooling pads reduce the unit's effectiveness.
Use a garden hose to rinse out the bottom and the inside of the unit. The dirt that accumulates is removed from the air during
operation, as the Pro-Kool® unit also acts as an air filter.
Remove the drain cap from the underside of the unit and let the unit drain completely. Rinse out any remaining dirt.
Replace the drain cap (finger tighten only).
Replace the cooling pads once they are dry.
Note: With proper use and regular cleaning, the cooling pads will last about two seasons. If you handle them wet and are abusive,
however, they will be easily damaged. Refer to page 15 for recommended conditioning and cleaning chemicals.
NORMAL STARTUP
NOTE: Some splattering may occur until pads are conditioned (may take several uses).
1.
Move the unit to the place where it will be run. Do not attempt to lift or move the unit once it is filled as damage to the unit or a large
spill may occur.
Note: When you decide where to place the unit, make sure there are no obstructions in the way that will disrupt or block the
airflow. Make sure the unit is level at all times. Keep the unit at least three feet away from walls or other obstructions that will
interfere with airflow into the unit.
2.
3.
4.
5.
6.
7.
8.
Check to insure the drain cap is in place and secure.
Connect the garden hose to the brass hose adapter. Check that there is a washer in the hose connection's female end.
Open the water supply valve and check that water enters the bottom through the float valve by removing one cooling pad. Allow the
unit to fill and check that the float valve completely shuts off the water.
If you are manually filling, remove one or more cooling pads and fill the bottom with a bucket or hose.
Visually monitor the filling operation to avoid overflowing and causing spill damage.
Plug the unit into an outlet.
Turn the switch to the low cool position, then to high cool if more air is desired.
CAUTION: Do not run the pump without water in the bottom or you will damage the pump. Running the pump dry will void the
warranty on the pump.
NORMAL SHUTDOWN
1.
2.
3.
4.
5.
Turn the switch to the High Vent position, and let the unit run until the cooling pads are dry. This will maximize the life of the pads.
Turn the switch to the OFF position. Unplug the unit if you are going to clean the pads or inspect the components.
Shut off the water supply.
Drain the bottom if you are going to clean it or store it. It can be done two ways:
a) Remove drain cap from bottom of unit.
b) Attach garden hose to hose fitting labeled drain. Place valve handle in the drain position and put switch to pump only.
Note: Monitor water level and shut pump off when unit is empty. DO NOT RUN PUMP DRY.
If the unit will be stored for the season, insure the cooling pads are completely dry, and then remove them. Wrap them in plastic bags
or store them in a clean place where they will not be damaged or get dirty. The unit should be cleaned thoroughly before storing.
7
Troubleshooting
COOLING PADS NOT WETTING
1.
2.
3.
Make sure the unit has water.
Check to insure the control switch is in the proper position.
Make sure the pump is running.
4.
Pump is running but no water:
a.
Ensure hose is connected.
b.
Ensure the impeller on the inside of the pump turns freely.
5.
Pump is not running:
a.
A certified electrician must check wiring from pump to pump selector switch.
b.
If the wiring is correct, replace the pump.
FOAMING
Foaming is generally caused by a dirty water supply or contaminated water in the bottom.
1.
2.
3.
If foaming occurs, stop the unit, drain it and flush the bottom and insides thoroughly with clean water.
Clean the pads and do not use any kind of chemical cleaners. Refer to the "Regular Cleaning" section for proper procedure for
cleaning the pads.
Reassemble, refill and restart.
LINE CLOGS OR OBSTRUCTIONS (Little or no water flow)
Depending on the cleanliness of the water and the amount of dirt, dust, etc. in the supply air, you may have to clean the PVC pipes from
time to time. Your own experience will dictate the frequency.
1.
2.
3.
4.
5.
6.
7.
Turn off the unit and unplug it.
Remove the pads.
Locate the two PVC pipes in the top housing. Each PVC pipe is secured to an elbow connector by a hose. Remove this clamp from
both PVC pipes.
Grip the opposite end of each PVC pipe with pliers and gently twist it out of its "Y" connector.
Direct a jet of water at the series of outlet holes in the PVC pipes to blow them clear.
Direct the water nozzle into the end of each pipe and blow them clear. Inspect them for cleanliness and repeat if necessary.
Replace the PVC pipes taking care to ensure the water outlet holes are facing inwards at 90° towards deflector plate.
Note: Ensure you push the PVC pipes fully onto the elbow, and attach hose clamps.
ODOR CONTROL
Water source needs to be of good quality and regular maintenance is imperative. Pro-Kool® Water Conditioner is available from the factory.
See page 9.
LIME OR SCALE BUILDUP
Insure water source is of good quality and regular maintenance is being conducted. Pro-Kool® Water Conditioner is available from the
factory. See page 9.
SPLATTERING
If more or less water is desired, adjust PVC ball valve (see page 11, item 22).
LEAKING
Out Bottom
Check for cracks on the bottom. If a crack is found, repair it by using a Pro-Kool® Repair Kit or replace the entire bottom.
1. Insure drain cap is installed and hand tightened (drain cap must have gasket inside).
8
Optional Accessories
Your Pro-Kool® Evaporative cooler can be purchased with accessories/options or some of these options can be retrofitted to your Pro-Kool®
after the initial purchase. Necessary instructions are included with all equipment purchased separate from your Pro-Kool®.
Accessories or Options available at time of purchase or after purchase:
•
Pneumatic Wheels
•
Water Conditioner & Cleaner
Pneumatic Wheel Option
Pneumatic wheels are available at the time of your Pro-Kool® purchase or as a retrofit kit on a previously
purchased Pro-Kool®.
The pneumatic wheel options includes two locking and two non-locking wheels.
Pneumatic wheels are designed to allow for easy rolling on rough or uneven surfaces.
Water Conditioner & Cleaner
Cleaner is recommended to remove scale buildup
from the water supply system.
Water Conditioner is
recommended to control odors
found to be present in some
water sources.
• Clean Pro-Kool® according to the instructions
on page 7 of this manual.
• Place the tab under the float
valve water outlet for quick,
fast odor control.
• Refill with water and add one (1) pint of Cooler
Cleaner Treatment to the water reservoir.
• Operate the Pro-Kool® in the "pump only" mode
for approximately 20 minutes. Refill Pro-Kool®
with fresh water.
• Place the tab next to the
pump for longer lasting and
more constant odor control.
• Repeat treatment steps if deemed necessary.
• Operate Pro-Kool® in normal manner and
repeat treatment when evidence of scale
build-up begins.
9
Pro-Kool® Parts List
1
7
6
2
3
5
4
Item
Schaefer P/N
Description
1
42PKTH
Top housing
2
42PKBH
Bottom housing
3
WC-CASTERS5
5" caster
4
WC-CASTERLGLK
5" locking caster
5
42PKSF
Support frame
6
42PKFG
Front guard
7
WC-SWITCH
6-position switch
10
Pro-Kool® Parts List
13
12
11
10
9
8
25
24
14
23
22
15
16
21
17
20
18
19
Actual Pro-Kool® may vary
slightly from unit shown here.
Item
Schaefer P/N
Description
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
VH58ID
SSFB-426
AK-94C
A55
WC-SWITCHCORDLG
WC-PUMPCORD
WC-1HPMTR
WC-MTRCORD
PK-PCB15
PK-PUMP1200
42PKDR
PVCCAP112
DFV
BV34
PVCBV
42PKMFMB
PBBA205-16
FS1X14
PK-PVCP12X4512
42PK-SDP
42PKPAD
5/8" ID vinyl hose
Stainless steel 42" 6-wing fan blade
9.25" diameter composite pulley
55" V-belt
Switch to motor electrical pigtail
Switch to pump electrical pigtail
1 HP 2-speed evap. cooler motor
Electrial motor cord
Black 15' power cord
1200 GPH pump
Drain rail
1 1/2" drain cap (under unit)
Float valve
3/4" brass ball valve
PVC ball valve
Motor/fan mounting bracket
Pillow block bearings
Fan shaft
1/2" PVC pipe
Spray deflector plate
Evaporative cooling pad
26
11
27
Pro-Kool® Performance Chart
Pro
12
Pro
Wet Bulb Temperature = Wet Bulb Temperature @ Current Relative Humidity
Dry Bulb Temperature = Current Ambient Air Temperature
Temperature Difference = Dry Bulb Temperature Minus Wet Bulb Temperature
Temperature Drop = Temperature Difference Multiplied by 72%
Output Temperature = Dry Bulb Temperature Minus Temperature Drop
Pro-Kool® Humidity Charts
13
General
Support Information
Using this equipment for any other purpose than it was intended or in a way not within the operating recommendations specified in this
manual will void the warranty and may cause personal injury.
This manual is designed to provide comprehensive planning, installation, safety, operation, maintenance, troubleshooting and parts
information. The Table of Contents provides a convenient overview of the information in this manual.
Thank you
The employees of Schaefer Ventilation Equipment would like to thank you for your recent Schaefer purchase. If a problem should arise,
your Schaefer dealer can supply the necessary information to help you.
Dealer & Product Information
Dealer’s Name:
Dealer’s Address:
Dealer’s Phone:
Date of Purchase:
Ordering Replacement Parts
To order replacement parts contact the dealer from whom you purchased your Pro-Kool®. If you do not have that information,
please call Schaefer Ventilation Equipment at 800-779-3267 to locate a dealer near you.
Keep this manual in a clean, dry place for future reference.
Pro
14
Warranty
Schaefer Ventilation Equipment, LLC. warrants to the original purchaser that our products which prove to be defective in material or
workmanship within one year (unless otherwise specified) from date of purchase will be repaired or replaced at the option of Schaefer
Ventilation Equipment, LLC. F.O.B. Sauk Rapids, Minnesota.
What is Not Covered By The Warranty
The warranty does not cover:
(1)
(2)
(3)
(4)
Installations not made in accordance with installation instructions;
Where the operation of the product varies substantially from our operating instructions;
Malfunctions resulting from misuse, negligence, alteration, accident or lack of performance of required maintenance;
Loss of time, inconvenience, loss of use of the product, or other consequential damages.
The above constitutes our sole warranty.
THERE IS NO WARRANTY OF MERCHANTABILITY AND THERE ARE NO WARRANTIES WHICH EXTEND
BEYOND THE DESCRIPTION OF THE FACE HEREOF.
Products with warranty periods that exceed our standard one-year warranty are listed below. These products are subject to all
other provisions as stated in The Schaefer Warranty.
25 Years 15 Years 10 Years 5 Years 3 Years 2 Years 2 Years 1 Year -
Poly Housings
Fiberglass Housings
VersaHeat® IRLens™ Ceramic Emitters for Gas Units
Schaefer GQ Tube Heater Combustion and Heat Exchanger Tubes
PC Compatible Controls
Certain Manual and Variable Speed Controls
Schaefer GQ Tube Heater Burner Controls
Schaefer K-Series, 2-Stage, Compact Heater and the Stainless Steel Tube Heaters
Products with warranty periods less than the stated one-year warranty are listed below. These products are subject to all other
provisions as stated in The Schaefer Warranty.
120 Days - VersaHeat® IRLens™ Elements for Electric Units
800-779-3267
[email protected] • www.schaeferfan.com
©2007 Schaefer Ventilation Equipment 6-8-07
15
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement