Classe Audio CDT-300 User Guide Manual Operating Instruction Pdf

Owner’s Manual
CDT-300
DVD Transport
Downloaded From DvDPlayer-Manual.com Classe Audio Manuals
WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK,
DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE.
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION: TO REDUCE THE RISK OF ELECTRICAL SHOCK, DO
NOT REMOVE COVER. NO USER-SERVICEABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED PERSONNEL.
NOTICE
All of us at Classé take extreme care to ensure that your purchase will remain a prized investment. We are proud to inform you that all
Classé components have been officially approved for the European Community (CE) mark.
This means that your Classé product was subjected to the most rigorous manufacturing and safety tests in the world. The CE mark certifies
that your purchase meets or exceeds all European Community requirements for unit-to-unit consistency and consumer safety.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this
equipment does cause interference to radio or television reception, which can be determined by turning the equipment on and off, the user
is encouraged to try to correct the interference by one or more of the following measures:
•
•
•
•
Reorient or relocate the receiving antenna;
Increase the separation between the equipment and the receiver;
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected;
Consult the dealer or an experienced radio/TV technician for help.
CAUTION: Changes or modifications to this equipment not expressly approved by the manufacturer could void the user’s authority to
operate the equipment.
This product incorporates copyright protection technology that is protected by U.S. patents ad other intellectual property rights. Use of this
copyright protection technology must be authorized by Macrovision, and is intended for home and other limited viewing uses otherwise
authorized by Macrovision. Reverse engineering or disassembly is prohibited.
The information contained in the manual is subject to change without notice. The most current version of this manual will be posted on
our web site at http://www.classeaudio.com.
Marking by the “CE” symbol (shown left) indicates compliance of this device with the EMC
(Electromagnetic Compatibility) and LVD (Low Voltage Directive) standards of the European
Community.
Classé products are designed to comply with international directives on the Restriction of Hazardous
Substances (RoHS) in electrical and electronic equipment and the disposal of Waste Electrical and
Electronic Equipment (WEEE). The crossed wheelie bin symbol indicates compliance and that the
products must be appropriately recycled or processed in accordance with these directives.
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause
harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation.
Please record the serial number for your new Classé component here for future reference.
Serial #: ____________________________________________
2
Downloaded From DvDPlayer-Manual.com Classe Audio Manuals
Important Safety Instructions
1.
Read these instructions.
2.
Keep these instructions.
3.
Heed all warnings.
4.
Follow all instructions.
5.
Do not use this apparatus near water.
6.
Clean only with dry cloth.
7.
Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions.
8.
Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including
amplifiers) that produce heat.
9.
Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades
with one wider than the other. A grounding type plug has two blades and a third grounding prong. The
wide blade or the third prong are provided for your safety. If the provided plug does not fit into your outlet,
consult an electrician for replacement of the obsolete outlet.
10. Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and
the point where they exit from the apparatus.
11. Only use attachments/accessories specified by the manufacturer.
12.
Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with
the apparatus. When a cart is used, use caution when moving the cart/apparatus combination to
avoid injury from tip-over.
13. Unplug this apparatus during lightning storms or when unused for long periods of time.
14. Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged
in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into
the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been
dropped.
15. Do not expose this apparatus to dripping or splashing and ensure that no objects filled with liquids, such as
vases, are placed on the apparatus.
16. To completely disconnect this apparatus from the AC Mains, disconnect the power supply cord plug from
the AC receptacle.
17. The mains plug of the power supply cord shall remain readily operable.
18. Do not expose batteries to excessive heat such as sunshine, fire or the like.
The lightning flash with arrowhead symbol within an equilateral triangle is intended to alert the user
to the presence of uninsulated “dangerous voltage “ within the product’s enclosure that may be of
sufficient magnitude to constitute a risk of electric shock to persons.
The exclamation point within an equilateral triangle is intended to alert the user to the presence of
important operating and maintenance (servicing) instructions in the literature accompanying the
product.
WARNING: To reduce the risk of fire or electric shock, do not expose this apparatus to rain or moisture.
3
Downloaded From DvDPlayer-Manual.com Classe Audio Manuals
Contents
Welcome to the Classé family ........................................................................... 6
a word about installation ............................................................................ 6
Unpacking and Placement ................................................................................ 7
unpacking your unit ................................................................................... 7
placement .................................................................................................. 7
ventilation .................................................................................................. 7
custom installations .................................................................................... 7
serial number ............................................................................................. 7
register your purchase! ............................................................................... 8
operating voltage ........................................................................................ 8
warm up/break-in period ............................................................................ 9
please read this manual .............................................................................. 9
Special Design Features .................................................................................. 10
flexible GUI .............................................................................................. 10
highly refined circuit design ..................................................................... 10
extensive listening tests............................................................................. 10
extraordinary longevity ............................................................................. 10
Front Panel...................................................................................................... 11
Rear Panel....................................................................................................... 13
coaxial digital output ......................................................................... 14
AES/EBU digital output....................................................................... 14
optical digital output .......................................................................... 14
The Remote Control ........................................................................................ 18
Using the CDT-300 ......................................................................................... 21
CD operational menu ............................................................................... 21
playlist ............................................................................................... 21
controls menu .................................................................................... 22
repeat mode ....................................................................................... 22
shuffle ................................................................................................ 22
time display ....................................................................................... 22
program ............................................................................................. 22
DVD operational menu ............................................................................ 23
the home screen ................................................................................ 23
controls .............................................................................................. 23
The Menu System ........................................................................................... 24
main menu system.................................................................................... 24
system setup....................................................................................... 24
teach IR.............................................................................................. 25
display setup ...................................................................................... 25
triggers ............................................................................................... 25
remote Fkeys ...................................................................................... 26
cautionary note on Fkey use .............................................................. 26
status .................................................................................................. 27
version info ........................................................................................ 27
sensors ............................................................................................... 27
CAN-Bus .................................................................................................. 27
features .............................................................................................. 27
hardware setup .................................................................................. 28
using CAN-Bus................................................................................... 29
4
Downloaded From DvDPlayer-Manual.com Classe Audio Manuals
CAN-Bus shared features .......................................................................... 30
configuration...................................................................................... 30
operate............................................................................................... 30
AC status ............................................................................................ 30
status .................................................................................................. 30
name.................................................................................................. 30
global brightness ................................................................................ 31
global standby ................................................................................... 31
CAN-Bus model specific features ............................................................. 31
PlayLink ............................................................................................. 31
amp info ............................................................................................ 32
event log ............................................................................................ 32
display setup menu................................................................................... 33
brightness........................................................................................... 33
timeout .............................................................................................. 33
language ............................................................................................ 34
colors ................................................................................................. 34
temporary display .............................................................................. 34
System Setup ................................................................................................... 35
the system setup menu system .................................................................. 35
audio setup ............................................................................................... 35
audio delay ........................................................................................ 36
digital output...................................................................................... 36
video setup ............................................................................................... 37
video standard ................................................................................... 37
aspect ratio ........................................................................................ 38
resolution ........................................................................................... 38
edge enhancement............................................................................. 38
color space ........................................................................................ 39
preference ................................................................................................ 39
audio format ...................................................................................... 39
audio language .................................................................................. 39
subtitle language ................................................................................ 39
CD autoplay....................................................................................... 39
navigation .......................................................................................... 40
parental control ........................................................................................ 40
Updating Your Unit ......................................................................................... 41
Troubleshooting .............................................................................................. 42
Care & Maintenance ....................................................................................... 44
Specifications .................................................................................................. 45
Dimensions ..................................................................................................... 46
5
Downloaded From DvDPlayer-Manual.com Classe Audio Manuals
Welcome to the Classé family
Congratulations on your purchase of a Classé product. It is the result of many
years of continuous refinement, and we are sure that you will enjoy it for many
years to come.
We value our relationship with our customers. Please allow us to stay in touch with
you by registering your warranty on the Classé website (www.classeaudio.com) or
by returning your warranty card now, before you pack up the shipping carton
of your new product and forget all about it. Doing so will enable us to let you
know about any possible future upgrades or updates that might become available
for your Classé component.
Registering your warranty also means that warranty service can be obtained
easily and quickly, even if you have mislaid your original sales slip.
You will find the warranty registration card at the end of the separate warranty
policy booklet, enclosed.
Please, take a few minutes to register your product online or fill out the warranty registration card, and drop it
in the mail.
a word about installation Every effort has been made to make the Classé CDT-300 simple and
straightforward to install and use.
Still, we have no way to evaluate other variables such as the size and shape
of your room, its acoustics, and the associated equipment you have chosen
to use with your DVD transport. All of these factors influence the ultimate
performance of your system.
For this reason, we strongly encourage you to have your
system installed and calibrated by your dealer, whose
experience, training, and specialized equipment can
make a profound difference in the final performance of
the system.
6
Downloaded From DvDPlayer-Manual.com Classe Audio Manuals
Unpacking and Placement
unpacking your unit Carefully unpack your DVD transport according to the supplied instructions,
and remove all accessories from the carton.
Important!
Keep all packing materials for future transport of
your Classé product. Shipping your new component
in anything other than its purpose-designed packing
material may result in damage that is not covered by the
warranty.
placement The CDT-300 has been designed to operate optimally on any stable and level
surface. Incorporating vibration damping within the CDT-300’s feet and CD/DVD
Drive Assembly, a high level of isolation from external disturbances is incorporated.
As with any digital component, it is best to place the CDT-300 somewhat
apart from your most sensitive analog electronics, particularly turntables and
preamplifiers. Generally, placing it on its own shelf should suffice.
Note that adequate clearance for the AC cord and connecting cables
must be left behind the CDT-300. We suggest leaving eight inches
(20 cm) of free space behind your DVD transport to allow all cables
sufficient room to bend without crimping or undue strain.
Classé recommends that the unit not be placed directly on the top surface of a
power amplifier (or any other heat source).
ventilation Your Classé DVD transport generates a certain amount of heat in the course
of normal operation. Be sure to allow three inches (75mm) of clearance above
it and three inches (75mm) to each side to allow heat dissipation through air
circulation. Avoid placement on soft surfaces that would restrict airflow (such as
plush carpeting).
custom installations Drawings are included in this manual to facilitate special installations and
custom cabinetry (see the section Dimensions). An optional, purpose-designed
rack mount kit is available for this product. Contact your Classé dealer for more
information.
serial number The serial number for your DVD transport is found on the rear of the unit.
Please note and record this number on the page entitled Important Safety
Instructions for your future reference.
7
Downloaded From DvDPlayer-Manual.com Classe Audio Manuals
register your purchase! Having found the serial number, now would be a good time to register your
product on the Classé web site or fill out the registration card. Please register
your purchase so we can advise you of updates and other items of interest.
It will take only a minute or so. Please register your product on line or complete
the card now, before you forget.
operating voltage The CDT-300 disc transport is set at the factory (internally) for 100V, 120V,
220V, 230V, or 240V AC mains operation, as appropriate for the country in
which it is to be sold. (230V only in European Union countries, in compliance
with CE regulations.) The voltage setting may not be changed by the user.
Make sure that the label on the rear panel of your DVD transport indicates
the correct AC operating voltage for your location. Attempting to operate your
DVD transport at an incorrect voltage may damage the unit.
Warning:
The voltage setting of your DVD transport may not be
changed by the user. There are no user-serviceable
parts within the unit. Please refer any problems to an
authorized Classé service center.
If the AC mains voltage indicated on your DVD transport is incorrect, please
contact your local authorized Classé dealer or distributor.
The CDT-300 includes protection circuitry that will prevent the transport from
operating at dangerously high or low voltages.
• At startup: the AC mains voltage must be within a range of approximately
-15% to +10% of its nominal value at startup, or the transport will not
turn on. For example, a 120V unit requires the AC mains to be between
approximately 95V–135V in order to turn on.
• Overvoltage during operation: if the AC mains voltage surges by roughly
10% or more during operation, the transport will enter protection mode
and shut down. The standby LED (Light-Emitting Diode) will flash to
indicate the protection mode has been engaged. An error message will be
displayed on the LCD touchscreen.
• Under-voltage during operation: if the AC mains voltage sags by 15%
or more, the transport will continue to play (since this does not present
a particular danger to the transport), but note that it may not be able
to achieve its usual standard of performance under these compromised
conditions. The Standby LED will flash to indicate the condition.
8
Downloaded From DvDPlayer-Manual.com Classe Audio Manuals
warm up/break-in period Your new Classé DVD transport will deliver outstanding performance
immediately. However, you should expect to hear it improve somewhat as
it reaches its normal operating temperatures and its various components
“break-in.” It has been our experience that the greatest changes occur within the
first 300 hours, as the transport reaches thermal equilibrium and the capacitors
fully form. After this initial break-in period, the performance of your new
product should remain quite consistent for years to come.
The only exception to this rule is if the unit is placed in standby or unplugged
for an extended period of time, allowing it to cool down. Depending on the
degree of cooling involved, you should expect a brief warm-up period before
the its sound quality is at its best. Unless your DVD transport was allowed
to become quite chilled, subsequent thermal re-stabilization should not take
long. Fortunately, you should never have to repeat the initial 300 hour break-in
period.
please read this manual… Please take a few minutes to review this manual, and to familiarize yourself
with your new DVD transport. We understand that you are anxious to plug
everything in and get started. However, reading this manual and following the
advice it gives will ensure that you get all the benefits you deserve from having
purchased such a fine piece of equipment.
9
Downloaded From DvDPlayer-Manual.com Classe Audio Manuals
Special Design Features
flexible GUI The LCD touchscreen on the front panel of your new component supports an
extremely flexible and versatile graphical user interface (GUI) while maintaining
a clean, uncluttered appearance. The CDT-300 provides a range of controls
that might otherwise require dozens of buttons and knobs on the front panel.
Despite this power and flexibility, it remains simple to operate in day-to-day use.
highly refined Classé products are designed to deliver consistent, state-of-the-art performance
circuit design over many years of use. With this in mind, our engineers have developed
electronic circuitry that offers both exceptional performance and stability in
equal measure.
Starting with innovative circuit designs, we engineer them to optimum levels
by applying meticulous attention to detail at all phases of the design and
component selection process. By measuring, listening and viewing in an
interactive manner we conclude whether our design goals have been met.
Finally, our designs are subjected to extensive testing to ensure longevity,
reliability, and stability.
extensive listening tests Throughout the development phase, perhaps the most important testing of
all is listening and viewing our work. Subjective listening is highly valued at
Classé, as striking a balance between products that both measure exceptionally
and sound fabulous is our aim. We take the same approach with video, wherein
sophisticated video measuring equipment is used in conjunction with subjective
viewing.
extraordinary longevity Another benefit of having worked with highly refined circuit designs so
extensively over many years is that we have vast experience in what works well
over the long term.
By using only the highest quality parts to begin with, and then using them in an
informed way as a result of both accelerated aging experiments and actual longterm experience, we are able to design and manufacture products which we are
confident will stand the test of time.
We are confident that your new Classé DVD transport will give you many
years of trouble-free reliability and musical enjoyment, just as previous Classé
products have given their owners.
10
Downloaded From DvDPlayer-Manual.com Classe Audio Manuals
%*%#4
-%.5
#$4
/0
1
23
Front Panel
1
Standby button & LED indicator
The front panel Standby button will toggle the transport between its fully
operational status and a standby mode that leaves the transport off, yet
ready to respond to system commands via any of the supported control
options (e.g. IR input, DC trigger, CAN-Bus, or RS-232).
The current state of the transport is indicated by the LED on the Standby
button on the front panel. When the unit is powered and switched on, this
LED indicates the following:
•
•
•
•
On
Flashing (on power-up)
Off
Flashing (after power-up)
=
=
=
=
standby
initialization
operate
AC mains voltage out of range
If you are not going to use the transport for an extended period of
time, e.g. vacation or other travel, we suggest you disconnect it from
the AC mains. Please be certain that the transport is in standby prior to
disconnecting it from the AC mains.
Also, it is a good practice to physically disconnect any and all valuable
electronics from the AC mains during electrical storms, as a lightning
strike anywhere near your home can put a tremendous surge on the AC
mains that will easily jump across a simple power switch. The resulting
surge (which may be many thousands of volts) can damage any piece
of electronics, no matter how well designed and protected. The best
protection in the case of severe electrical storms is simply to remove the
electronics from any connection with the power grid.
11
Downloaded From DvDPlayer-Manual.com Classe Audio Manuals
2
Menu button
Pressing the front panel Menu button will call up the menu system,
replacing the normal status display in the LCD touchscreen of the
CDT-300.
3
LCD touchscreen
Most of your interaction with the CDT-300 will be with the front panel
LCD touchscreen (and with the CDT-300’s supplied remote control).
It will usually display the information you are accustomed to seeing on
the front of most CD and DVD transports (track number, time, etc.), as
well as the basic transport controls. In addition, the touchscreen can be
used to preview videos you may be “cueing up” for friends or family, and
to navigate DVD-Audio discs’ menu systems without the distraction of
having to turn on your main video display.
By pressing the Menu button, you can also call up the menu system of the
CDT-300, which gives you control over many of the operational details
of the DVD transport, including system setup options, various display
options (including the language in which the menu system itself displays),
and several custom-installation capabilities that allow superior integration
of the CDT-300 into complex systems.
For more information, see the section The Menu System later in this
manual.
4
Eject button
The front panel Eject button operates the slot-loading mechanism of the
CDT-300. It will eject a loaded disc. There may be a short delay prior to
ejection whilst a disc is playing, in order to give the disc time to come to a
stop.
A blue light illuminates the slot when there is no disc loaded.
5
IR window
The infrared (IR) receiver and transmitter are located behind this
window. Ordinarily, your Classé CDT-300 must be able to “see” the
remote control from this window in order to respond to remote control
commands.
If your DVD transport will be located behind closed doors, or for any
other reason will not be able to “see” the remote control during normal
operation, you may use the rear panel IR input and output mini-jacks
and an IR repeater system to solve the problem. For more information
about using an infrared repeater system to route signals to and from the
CDT-300, refer to the section Rear Panel later in this manual, or contact
your local Classé dealer.
12
Downloaded From DvDPlayer-Manual.com Classe Audio Manuals
COMPOSITE
S-VIDEO
Pr
Pb
Y
100/120~ T500mAL250V
230/240~ T250mAL250V
/.
CAUTION! TO REDUCE THE RISK OF ELECTRIC SHOCK, GROUNDING
OF THE CENTER PIN OF THIS PLUG MUST BE MAINTAINED
/&&
AVIS! POUR RÉDUIRE LE RISQUE DE CHOC ÉLECTRIQUE
LA FICHE CENTRALE DE LA PRISE DOIT ÊTRE
BRANCHÉE POUR MAINTENIR LA MISE À LA TERRE
Rear Panel
1
Analog Video Outputs
The CDT-300 is equipped with a complete set of analog video outputs:
Component (Y, Pb, Pr), S-Video, and Composite. The S-Video output
employs the standard S-Video (mini-DIN) connector, while the
Component and Composite outputs employ high quality RCA connectors.
Note that the three analog video standards offer varying degrees of
performance:
• Component video renders the best analog video quality, and
provides compatibility with progressive and high definition
video signals. As a result, the component outputs are the analog
outputs you will want to use in order to take full advantage of
the video scaling and processing capabilities of the CDT-300.
(The HDMI output also supports video scaling and processing.)
• S-Video is capable of rendering a high quality video image, but is
limited to standard definition, interlaced signals.
• Composite video is the most common analog video interface,
available on almost all display devices. Like S-video, it is also
limited to standard definition, interlaced signals.
For this reason, you are advised to use component video connections
whenever possible.
All three analog video outputs are active simultaneously. Connect the
appropriate video output(s) of the CDT-300 to the corresponding inputs
of your A/V preamplifier/processor using high quality video cables. Your
Classé dealer can assist you in making an appropriate cable selection.
Note that due to Macrovision copy protection software, all HD resolutions
may not be available depending on the disc.
13
Downloaded From DvDPlayer-Manual.com Classe Audio Manuals
2 HDMI Digital Video Output
The HDMI output of the CDT-300 provides for a direct, digital video
connection to your display. Digital display devices such as LCD and DLP™
are used increasingly in modern home theater settings; HDMI allows
you to keep the video signal in its digital form all the way to the display,
offering stunning clarity and realism.
In addition, HDMI carries the multichannel audio signal and some
additional data about the signal being played. When fully implemented,
it can become the only connection between the DVD transport and the
A/V preamplifier/processor. (The A/V preamp retains the audio signal and
passes the video along to the display device.) More often, people prefer to
run separate audio and video cables since doing so offers some additional
flexibility as well as the potential for higher audio performance via
AES/EBU connection.
If your display has a DVI input rather than an HDMI input, contact your
Classé dealer about a suitable adapter cable. The DVI standard lacks the
audio capabilities of HDMI, and is growing less popular in the consumer
electronics world. A simple and inexpensive adapter can convert from the
HDMI connector to the DVI connector, and the electrical characteristics
of the digital video signals are the same.
3
Digital Outputs
The CDT-300 has three digital outputs, all of which carry the same
information. You may use whichever connection you prefer, consistent
with the available connections on your A/V preamplifier/processor. Only
one of the three connections is needed.
coaxial digital output
The coaxial digital output provides a digital audio signal via a 75Ω coaxial
cable equipped with RCA-type connectors. Connect this output to a
corresponding coaxial digital input on your preamplifier/processor.
AES/EBU digital output
The AES/EBU output provides a digital audio signal via a 110Ω balanced
cable equipped with XLR-type connectors. Connect this output to a
corresponding AES/EBU digital input on your preamplifier/processor.
optical digital output
The optical digital output provides a digital audio signal via a standard
EIAJ (“Toslink™”) optical cable. Connect this output to a corresponding
optical digital input on your preamplifier/processor.
Making any one of these connections allows you to feed the signal in its
digital form directly to your A/V preamplifier for further digital processing.
14
Downloaded From DvDPlayer-Manual.com Classe Audio Manuals
4
IR Input and Output
Your Classé DVD transport includes two 1⁄8th-inch mono mini-jacks in
order to support the infrared (IR) remote controls that are ubiquitous
today. Infrared commands exist (for example) for toggling the transport
between operate and standby, in addition to discrete command codes
for either operate or standby. These codes may be used in “macros” for
sophisticated remote control systems, facilitating the control of the
transport in the larger context of a complete system.
The list of commands available is quite extensive, enabling even complex
macros (chains of commands strung together) to operate flawlessly. If this
capability is of interest to you, we strongly recommend discussing it with
your authorized Classé dealer.
Note that IR Input and Output is a bit of a misnomer: the input and
output of these plugs is electrical in nature, not infrared. They are used
with standard IR receivers, distribution amplifiers, and emitters (available
from your dealer) to translate the remote’s IR signal to an electrical signal
and vice versa. The big advantages here include being able to easily route
the signals anywhere they might need to go and the reliability of a solid
electrical connection.
Since an IR distribution system such as your dealer may design for you
usually must control many products, your DVD transport includes both
an IR input (for the control of this product) and an IR output (so as to
pass along the same signal to the next product). This allows you to “daisy
chain” your control wires from one product to the next.
Note:
Many IR repeater systems do not yet support the
stripped-carrier signal format required by your DVD
transport. If yours does not, a Delta IR Interface may
be required to ensure compatibility between your IR
repeater system and your Delta-series Classé equipment.
Your dealer can assist you in designing an effective IR
repeater system.
The transport is designed to respond to IR commands of 5VDC, with the
tip of the mono mini-jacks defined to be “positive” relative to the shank of
the plug.
15
Downloaded From DvDPlayer-Manual.com Classe Audio Manuals
5
DC Trigger Input and Output
Many audio/video components can supply a DC control voltage to
associated equipment in order to induce desired behavior. Your Classé
DVD transport can take advantage of these capabilities in order to be
switched between operate and standby automatically, usually in concert with
the A/V preamp itself.
The 1⁄8th-inch mono mini-jack Trigger In provides for remote-controlled
turn-on (that is, toggling between operate and standby) of the transport.
Two 1⁄8th-inch mono mini-jacks provide individually controllable DC
trigger outputs which can be used for any of a number of purposes, as
described in The Menu System. For example, your dealer can program
Trigger Out to toggle your Classé power amplifier between operate and
standby with your CDT-300.
The remote Trigger In will respond to the presence of 5–12VDC, with tip
polarity as shown below:
Similarly, the Trigger Outs will create a 12VDC signal that can support up
to 100mA of current.
6
Classé CAN-Bus Control Ports
These RJ-45 connectors are reserved for future control and communication
applications using Classé Audio’s implementation of the Controller Area
Network (CAN) Bus specification.
7
RS-232 Control Port
This port has two purposes:
• downloading new operating software into your DVD transport
(should new features ever be added, for example)
• external control of your preamplifier by systems such as
i-Command™, AMX® and Crestron™
For more information, please contact your dealer and ask about home
automation systems.
16
Downloaded From DvDPlayer-Manual.com Classe Audio Manuals
8
Danger!
AC Mains Power Switch
The main power switch for the CDT-300 is located at the right side of the
rear panel. The transport should be in standby mode before being switched
off. Switching the unit on puts it in standby mode.
Potentially dangerous voltages and current capabilities
exist within your DVD transport, even when
disconnected from AC mains. Do not attempt to open
any portion of the transport’s cabinet. There are no userserviceable parts inside your DVD transport. All service
of this product must be referred to a qualified authorized
Classé dealer or distributor.
9
AC Mains Input
An IEC standard power cord (supplied) is used with the CDT-300. Plug
the cord into the IEC outlet provided, and the other end into a suitable
wall outlet.
The AC inlet assembly includes a built-in fuse for the protection of the
unit in case of major AC mains problems and/or component failure.
If your CDT-300 ever behaves as though it were not connected to the
AC mains (meaning it seems completely dead), remove the AC cord from
the unit and open the fuse holder immediately above the AC cord inlet.
If the fuse is blown, replace it with the spare fuse contained in the fuse
holder. If the spare fuse blows, take the unit to your qualified Classé dealer
immediately.
Caution:
There are no user-serviceable parts inside the CDT-300.
Do not attempt to diagnose the problem yourself.
17
Downloaded From DvDPlayer-Manual.com Classe Audio Manuals
The Remote Control
34!.$"9
).&/
$)30,!9
://-
!.',%
!5$)/
02/'
4)-%
35"4)4,%
Your new DVD transport comes with a versatile remote control which can
control both the CDT-300 itself and several aspects of the rest of a Classé-based
system. The keys are arranged in logical groups according to their functions.
1
6/,
-54%
Basic Functions
This section along the top of the remote control includes two groups of
four functions that control your basic interactions with the CDT-300. The
general group is located in the topmost row, and includes:
6/,
3%450
• Light switches the backlighting of the remote control on, for
better visibility under low-light conditions. After a few moments
of inactivity, the backlight switches off automatically.
• Info takes you directly to the status screen in the LCD menu
system, displaying several items of information about the
CDT-300 and its current operational status.
• Disp (for Display) cycles through the three brightness settings of
the screen display.
• Standby toggles the CDT-300 between standby and operate.
(/-%
%.4%2
$)3#
-%.5
4)4,%
2%0%!4
*5-0
&
&
&
The DVD-specific group addresses secondary features of the DVD
standard which you may have seen on other DVD transports, namely:
&
• Zoom cycles through the available “zoomed in” or magnified
views of the DVD.
• Angle cycles through the available camera angles of the DVD
being watched. (Relatively few discs take advantage of this optional
feature of the DVD standard.)
• Audio cycles through the various available soundtracks on the
disc being played. (You can set your preference in the menu system,
and it will become the default; this button cycles you through the
other options, should you want to explore them.)
• Subtitle cycles through the available subtitles in various
languages.
2
Numeric Keypad, Programming & Volume
The next section down on the remote control provides the numeric keypad
for use in directly accessing particular tracks on the CD/DVD you are
playing, as well as two keys that are frequently used in conjunction with
the numeric keys. The Volume and Mute controls are also in this section.
• The Numeric Keypad can be used to access specific tracks/
chapters directly from your remote control. Simply press the
appropriate number key (or keys) followed by the Play key. The
CDT-300 will go directly to your selection and begin to play.
For example, to play track 12, press the 1, 2, and Play keys in
sequence.
18
Downloaded From DvDPlayer-Manual.com Classe Audio Manuals
• Time cycles through the four time display modes:
time elapsed on track
time elapsed on disc
time remaining on track
time remaining on disc
• Prog (for Program) allows you to quickly and easily create a
programmed sequence of tracks (or chapters) to be played on the
current disc. Pressing Prog will take you directly to the program
page of the menu system, regardless of where you might be.
Once on the program page, you can change the highlighted track
using the Up and Down buttons, and can use the Enter button
to toggle whether it is included in the current program. Pressing
Prog a second time returns you to wherever you had been. (Note
that the program function is not available during play or pause,
only when the CDT-300 is in stop.)
3
Navigation Keys
The central section of the remote control contains the navigation keys.
This array of keys is similar to what you may have seen on remote controls
for DVD transports, and is used for navigation of the menu system of the
CDT-300.
• Setup serves two functions: it calls up the menu system when
you need it in order to adjust something to your preference;
once within the menu system, pressing Setup returns you to the
previous level of the menu system. If you press Setup when at
the top level of the menu system, it will take you back out of the
menu system to the normal display.
• Home returns you to the normal display of chapter/track, time,
and transport controls shown on the LCD screen on the front
panel of the CDT-300. This provides a quick way to get back to
normal operation, regardless of how deep you might be in the
menu system.
a note about DVD menus:
The DVD standard supports two levels of menus:
1) a menu of available “titles” on the disc (e.g.,
the main movie, plus extra “bonus” materials like
documentaries, etc.);
2) each “title” then has a subordinate menu of chapters
within the title.
• Disc Menu presents the menu of available chapters, within
whatever title you are watching at the moment. (See explanation
of DVD menus in this section.)
• Title gives you a list of available “titles” on the disc you are
watching. (See explanation of DVD menus in this section.)
• Up/Down/Left/Right keys allow you to move within a
particular menu screen, changing the highlighted item up/down/
left/right as you like, from the comfort of your chair.
• The Enter key allows you to select the highlighted item, having
the same effect as if you had pressed the button on the LCD
touchscreen.
19
Downloaded From DvDPlayer-Manual.com Classe Audio Manuals
4
Transport Controls
You will find the transport controls used to control the day-to-day
playback of discs just below the navigation keys.
•
•
•
•
•
•
•
•
•
5
(previous) will move backward through the chapters or tracks
(or the playlist, if you have created one), one step at a time. As
with most DVD players, the single exception to this is the first
time you press the key, which will take you to the beginning
of the track currently playing. Pressing the key again within
approximately one second will then take you to the previous
track.
/ (play) will start the disc spinning (if necessary) and start
playing the music, as expected.
(next) will move forward through the tracks (or the playlist, if
you have created one), one track at a time.
, (pause) will stop the music but allow the disc to continue
spinning; when you press Play, the music will start almost
immediately, and it will pick up from where you left off.
. (stop) applies to both the music and the spinning of the disc.
When you press Play, the disc will need to take a few moments
to get up to speed prior to playing, and it will play from the
beginning of the disc or the playlist (if one has been created for
the disc).
Repeat will cycle the CDT-300 through its repeat modes.
[ (scan reverse) provides a “rewind” function, the nature of
which is dictated by your navigation preference selection in the
menu system. (See The Menu System for more information.)
] (scan forward) provides a “fast forward” function, the nature
of which is dictated by your navigation preference selection in
the menu system. (See The Menu System for more information.)
^ (eject) will cause the inserted disc to spin down and then eject.
System Controls
The CDT-300 remote control also can control user-defined functions as
well as the volume and mute functions on a Classé system.
• F1/F2/F3/F4 keys are available for controlling aspects of the
CDT-300 not covered by the other buttons on the remote
control. You are able to choose what the CDT-300 should do in
response to receiving the infrared signal that a particular “Fkey”
has been pressed. The list of possible functions is quite extensive,
and is found in the menu system (see The Menu System section,
of this manual). For example, if you are using one of the DC
triggers on your CDT-300, you can toggle its state manually
using one of the Fkeys.
Note:
The Fkeys on all Classé remote controls issue the same
infrared commands. This saves you from having to be
sure you have grabbed the proper remote, since all your
Classé remotes will perform the same function for each
Fkey.
20
Downloaded From DvDPlayer-Manual.com Classe Audio Manuals
Using the CDT-300
Your CDT-300 includes a versatile touchscreen LCD display which supports
both an attractive information display and a flexible menu system. Because of
this flexibility, the CDT-300 can present different controls and capabilities when
playing a CD, and when playing a DVD. We will present these separately.
CD operational menu
The operational menu consists of several screens that can be accessed directly
from the normal display one sees when playing a CD. They are as follows:
playlist Pressing the playlist button on the display brings up the playlist for the current
disc. If you have not created a custom program for the disc, the playlist will
simply be a list of all the available tracks on the CD, in order. If you have created
a custom program (see below), it will be presented to you here. Note that this
display is mainly informational; you cannot edit the playlist from this screen.
You may, however, jump to any track by touching it on the screen.
21
Downloaded From DvDPlayer-Manual.com Classe Audio Manuals
controls menu The controls button on the operational display brings up a menu of controls,
including repeat mode, shuffle, time display, and program.
repeat mode Pressing the repeat mode button on the controls menu displays a screen on
which you may select any of the three repeat modes available: no repeat, repeat
track, and repeat disc. (If you have created a program, repeat disc will repeat the
program.)
shuffle Pressing shuffle on the controls menu will engage the shuffle mode, which
shuffles the playback order of the tracks on the current CD.
time display Pressing the time display button on the controls menu presents a screen with
four possible selections for how the current time of the disc playing is displayed:
elapsed on track, elapsed on disc, remaining on track, remaining on disc.
program Pressing the program button on the controls menu takes you to the
programming screen.
When you first load a CD, the default program for the disc is to play all
the tracks in their normal order (as you might expect). This is shown on the
programming screen as a list consisting of track 1 followed by track 2, track 3,
and so on. A sequence number appears to the left of each track, indicating its
place in the playlist.
The CDT-300 is capable of storing thousands of playlists.
If there is a song on the disc that you prefer to skip over, simply scroll to the
track in question by pressing the up or down arrows along the right side, and
then press the large button with the track number you do not want to hear.
It will no longer be highlighted, indicating that it has been removed from the
playlist for that CD. You can repeat this process for as many tracks as you would
like to delete.
If you want to create a completely different order in which the songs are played,
turn off the highlighting for all the tracks by touching each of their buttons
in turn. Then highlight the tracks one at a time, in your desired order. The
CDT-300 will build a new playlist based on your preferred sequence.
To remove a playlist, simply deselect all tracks and press the save button.
22
Downloaded From DvDPlayer-Manual.com Classe Audio Manuals
DVD operational menu When a DVD is inserted in the CDT-300, a different set of controls is displayed.
the home screen The home screen for DVDs is presented at left in the graphic above, and
contains basic information about where you are within the disc, as well as basic
navigation buttons similar to those on your remote control.
controls Pressing the controls button in the top right corner of the home screen takes
you to the controls screen. It contains six buttons:
• back will return you to the home screen
• repeat mode takes you to another screen in which you can select any of
the available repeat modes (no repeat, repeat chapter, repeat disc, and repeat
title).
• random will play chapters within the current title in random order. This
can be used to good advantage when watching a concert DVD, or when
listening to a DVD-Audio disc, in order to shuffle the order in which songs
are played.
• time display changes the way in which the CDT-300 will display the time
information of the disc being played. Your choices are: elapsed in chapter,
remaining in chapter, elapsed in title, remaining in title.
• DVD menu button will return you to the DVD menu of the disc
• title menu button will return you to the title menu of the disc.
23
Downloaded From DvDPlayer-Manual.com Classe Audio Manuals
The Menu System
The CDT-300 uses its versatile touchscreen display to make a wide variety of
setup choices and system defaults readily available. Using these menus, you can
easily customize the behavior of your DVD transport to suit your particular
system’s configuration, as well as your personal preferences.
main menu system Pressing the Menu button to the left of the LCD touchscreen brings up a
comprehensive menu system, the top two levels of which are shown below.
This menu system provides access to many installation-specific features that let
you customize how the CDT-300 works within the context of your particular
system.
system setup The most extensive part of the menu system is under the system setup button.
This section is both comprehensive and essential to taking full advantage of the
remarkable capabilities of the CDT-300. As such, it is described more fully in its
own, dedicated section of this manual. See System Setup for all the details.
24
Downloaded From DvDPlayer-Manual.com Classe Audio Manuals
teach IR The CDT-300 provides discrete infrared (IR) command codes for all its
functions, a list that extends far beyond what is required by normal remote
controls. However, many of these functions are critical if you plan to create
a customized remote control with macros that take command of your entire
system. Without these discrete codes, many of the macros you might want to
create will simply not work reliably.
The teach IR screen provides a scrolling list of all the available IR codes in the
CDT-300. By scrolling to the command your macro-capable remote needs to
learn, and then pressing the send IR code button, the CDT-300 will send the
appropriate command code out its front panel—where it can be learned by your
third-party remote control.
For more information on such control systems, we recommend you speak with
your authorized Classé dealer.
display setup This button brings up the display setup menu, which itself has subordinate
menus. For more detailed information, please see the display setup menu,
found later in this manual. (It allows you to configure the CDT-300’s LCD screen
brightness, the display timeout, the language used in the touchscreen and menu system
and the temporary display.)
triggers Each of the CDT-300 DC Triggers may be programmed as to its “logic level,”
which is to say, whether its voltage is low (essentially 0V), or high (approximately
12VDC) when the trigger is activated. The ability to change the level of a
trigger’s on state can solve installation-specific problems that otherwise require
external devices that add to both the cost and complexity of your system.
If this seems an obscure point, that’s okay. It is a feature designed to solve
problems you may not even have, but your installation professional appreciates
being able to solve such problems when they occur.
25
Downloaded From DvDPlayer-Manual.com Classe Audio Manuals
remote Fkeys This button brings up the remote Fkeys menu.
The remote control supplied with your Classé product includes four userprogrammable function keys, or “Fkeys.” They are labeled F1, F2, F3, and
F4, and are located near the bottom of the remote control. The “remote Fkeys”
menu allows you to define how your CDT-300 will respond to seeing one of
these Fkey signals. You can use the Fkeys to give you instant access to specific
system functions that might otherwise be buried in a menu somewhere.
For example, if you use the shuffle mode frequently, you may want to consider
programming one of the Fkeys to toggle that function on and off. Doing so will
save you having to access the control menu, followed by pressing the shuffle
button (which might be hard to see from across the room, even though you could do
so from the remote control with an Fkey assignment).
The remote Fkey menu has four buttons, one each for the four Fkeys on your
remote control. Pressing any of these buttons on the LCD touchscreen takes you
to a subordinate, scrolling list of possible functions for that particular Fkey.
Selecting the one you want is as simple as scrolling through the list (by touching
either the up or down arrows on the right), and then touching the specific
function in the list that you want that Fkey to perform.
cautionary note on Fkey use Note that all Classé remote controls provide these same four Fkeys, so that
you need not worry about which remote you happen to pick up. Thus F1 on
the preamplifier’s remote control sends the same infrared signal as F1 on the
CDT-300 remote control.
While this is intended to minimize confusion amongst different remotes (since
this aspect of them will all perform identically), you should take care when
assigning different functions on different components to the same Fkey. Doing
so would result in two components doing two different things at once, in
response to a single press of a button on the remote control. This can sometimes
be useful. As an example, F1 could set the preamplifier to the CD input, and
also set the DVD transport to Play, both from the press of a single Fkey.
26
Downloaded From DvDPlayer-Manual.com Classe Audio Manuals
status The status screen provides several items of information on the currently playing
disc, as well as access to information on the software used in and the internal
sensors of the CDT-300.
version info The version info button on the status screen takes you to the version
information screen. From time to time Classé develops new software that adds
features or enhances the operation of the DVD transport. Each new software
version has its own Version Number. The Version Info Screen displays the
Version Number of the software that your unit is running. The latest software
is always posted on the Classé website (www.classeaudio.com). If the version
number displayed on the Version Info Screen is lower than the version posted
on the Classé website, you may want to update your unit. Simple and detailed
updated instructions are also provided on the website. If you ever have occasion
to call our technical support people to ask a question not covered in this manual,
they may want to know precisely what software your unit is running. Having
this information available will help them to give you the best possible service.
sensors The sensors button on the status screen takes you to the sensors screen, which
displays information about several internal sensors within the CDT-300. It is
unlikely you might ever need the sensor information, unless directed to do so by
a customer service representative at Classé in order to help troubleshoot some
unexpected problem.
CAN-Bus Classé’s Controller Area Network, or CAN-Bus, opens the way to a new level
of interaction between our Delta range of amplifiers, preamps, processors and
source components. When the CDT-300 is connected with CAN-Bus, the
different elements of a Delta series system are in constant communication,
creating a “global” network that delivers system wide status information and
shared operational features, all through the touchscreen display.
features CAN-Bus will allow a single Delta series touchscreen to:
• Display status information for every connected unit, including amplifiers
which do not have a touchscreen display.
• Create a “PlayLink” that allows an SSP or Preamp to automatically switch
to the correct input when a Delta series source component starts playback.
• Adjust the global system brightness.
• Configure the entire system to go in and out of standby at the touch of a
button and also bring individual components in and out of standby.
• Mute any connected unit.
27
Downloaded From DvDPlayer-Manual.com Classe Audio Manuals
hardware setup 1
Classé Delta Series Products
Two or more Classé Delta series products are required, at least one of which
must have a touchscreen display.
2
Category 5 Network Cables
These are ordinary network cables, commonly used for broadband Internet
connections. They should be typical “straight through” cables not the “crossed
over” type, and the total required will be one less than the total number of
Delta series components in your system.
3
CAN-Bus Terminator
A single CAN-Bus Terminator may be required. It is inserted into the
CAN-Bus OUT connector of the last component in the CAN-Bus daisy
chain. One is included in the box with your CDT-300. They are also
available free of charge from your nearest Classé Customer Support Centre
http://www.Classeaudio.com/support/service.htm
4
SSP-300 & 600 CAN-Bus Interface Box
Systems that include an SSP-600 or SSP-300 will also require an
SSP-300/600 CAN-Bus Interface Box. These are included with the products or
available free of charge from your nearest Classé Customer Support Centre
http://www.Classeaudio.com/support/service.htm
28
Downloaded From DvDPlayer-Manual.com Classe Audio Manuals
The diagrams below illustrate how to connect the CAN-Bus hardware.
Any combination of models in any order without SSP-300 or SSP-600.
CAN-BUS
IN
OUT
CAN-BUS
IN
OUT
CAN-BUS
IN
OUT
CAN-BUS
IN
OUT
Any combination of models in any order with SSP-300 or SSP-600.
CAN-BUS
IN
OUT
CAN-BUS
IN
OUT
CAN-BUS
IN
OUT
CAN-BUS
IN
OUT
NOTE: Daisy chain may need to be terminated with CAN-Bus Terminator.
using CAN-Bus CAN-Bus is controlled via the touchscreen of any Delta series component. There
is no master component, so Delta series systems where two or more units have
a touchscreen can be controlled through any of the touchscreens. However, it is
probably easiest to start using CAN-Bus through just one.
CAN-Bus is accessed by pressing the menu button on the face of the unit or
remote, then the status button, followed by the more button.
29
Downloaded From DvDPlayer-Manual.com Classe Audio Manuals
The touchscreen will then display the CAN-Bus devices screen, which lists
connected Delta series components by model & serial number.
Highlighting a unit on the CAN-Bus devices screen identifies it as the target
unit. The front panel LEDs of the target unit will start flashing (unless you
highlight the unit that you are using to access CAN-Bus).
Once you have chosen the target unit press select. The target unit’s LEDs will
stop flashing and the touch screen will list the CAN-Bus features available to it.
Some CAN-Bus features are shared by all models, some are specific to individual
models.
CAN-Bus shared features The following CAN-Bus features are shared by all models.
configuration Selecting configuration will present the CAN-Bus configuration screen
allowing access to name, global brightness, and global standby features.
operate The operate settings allow you to bring the target unit in and out of standby, or
mute. This key will be disabled for the unit whose touchscreen you are using to
access CAN-Bus.
AC status The AC status screen displays information from the target unit’s electrical supply
sensors. Two screens are available, with the second accessed by selecting more.
status The status screen is the simplest way to access essential information about
the target unit. It displays the target unit’s model number, software version,
operational status and serial number.
name Allows you to set the name that this component will be listed under in the
CAN-Bus devices screen. The name will appear next to the unit model and serial
number, and facilitate the identification of units in large systems.
30
Downloaded From DvDPlayer-Manual.com Classe Audio Manuals
global brightness By setting all your components to global brightness you can adjust the
touchscreen and LED brightness for your entire system by changing the
brightness of a single touchscreen. All CAN-Bus software updates automatically
set the updated unit to Global Brightness. If you want a particular unit to be
excluded from Global Brightness, deselect Global Brightness for that unit.
global standby By setting all your components to global standby you can bring your entire
system in and out of standby by pressing the standby button of any unit or
remote. All CAN-Bus software updates automatically set the updated unit to
global standby. If you want a particular unit to be excluded from global standby,
deselect global standby for that unit.
CAN-Bus model The following CAN-Bus features are model specific.
specific features
PlayLink This feature is exclusive to Delta series disc players and will only function if
the disc player is connected to a CAN-Bus enabled preamp or surround sound
processor.
When PlayLink is active, pressing play on the disc player will also automatically
switch the preamp/processor to a specified input. This means that you can listen
to a CD or watch a DVD literally at the touch of a button.
The first step in using PlayLink is to choose the input you wish to be selected
when play is pressed on the disc player. Press the PlayLink icon, then select the
correct input from the list.
Once you have selected the input press back, then select configuration.
PlayLink is activated and disabled through the PlayLink icon on the CAN-Bus
configuration screen.
31
Downloaded From DvDPlayer-Manual.com Classe Audio Manuals
PlayLink is automatically active after a software update, and the PlayLink icon
will only appear on the CAN-Bus configuration screen of a Delta series disc
player.
PlayLink can only select a single input per disc player. It is therefore
not designed for users who regularly play both CDs and DVDs
through different inputs from a single disc player. When PlayLink is
active the disc player will default to the same input every time play is
pressed, regardless of whether it is playing CD or DVD.
amp info Available for amplifiers only, this screen displays the data provided by the
heatsink and AC Module temperature sensors.
NOTE: This feature is only accessible when the target amplifier is on.
event log Reserved for amplifiers, this feature is a protection circuitry event log which can
only be accessed when the target amplifier is in standby. The protection circuit
shuts down the amplifier or channel if it overheats or if its output could damage
your speakers. The event log details the circumstances surrounding the amp
going into protection and should be referred to in situations that require the
intervention of your dealer or Classé customer support.
The log can report the following events interpreted as follows:
• +ve slow blo trip & -ve slow blo trip — The average current has reached
the safe operating limit.
• +ve fast blo trip & -ve fast blo trip — The peak current has reached the
safe operating limit.
• over temperature trip — The unit temperature has reached the safe
operating limit.
• DC protection trip — The DC output level has reached the safe operating
limit.
• Communication failure — There has been a loss of communication
between the amp’s system monitoring sensors.
• AC line trip — The power supply has reached the limits of the amp’s safe
operating range.
These events are rare and generally occur due to issues that are external to the
amp. They should be interpreted positively. The amp is doing what it’s designed
to do.
32
Downloaded From DvDPlayer-Manual.com Classe Audio Manuals
display setup menu
The display setup menu allows you to define your preferences for three aspects
of the CDT-300’s LCD display: the brightness of the backlighting, the timeout
of the backlighting, and the language used.
brightness The brightness setting of the CDT-300 has three possible values: low, medium,
and high. Select the appropriate setting based on the level of ambient light
typically found in your listening room while using the system. A high brightness
setting usually works best in brightly-lit rooms; you may find that a lower setting
is less visually intrusive under more subdued lighting conditions.
timeout If you prefer listening to music in a dimly-lit or darkened room, you may find
even the low brightness setting of the display somewhat distracting. If so, you
can vary the timeout of the backlighting so as to turn it off entirely after a
period of inactivity you select.
In this context, activity refers to any use of the user interface. This includes hard
buttons, the LCD touchscreen, and the remote control.
For example, if you reduce the timeout to its minimum setting, the backlighting
will illuminate the display as soon as you interact with any of the CDT-300
controls, and stay on for only three seconds—just long enough for you to check
on something. If you continue to use any of the controls (at least once every
three seconds), the display will remain lit. It will then extinguish itself after three
seconds of inactivity on your part.
33
Downloaded From DvDPlayer-Manual.com Classe Audio Manuals
If you prefer the display of the CDT-300 to remain on whenever not in
standby, choose the never timeout setting. The lamp in the LCD display was
designed for harsh automotive environments and will give you many years of
reliable operation. If you plan to leave the unit on continuously, however, we
recommend that you keep the timeout delay set to less than one minute. (Note
that setting the brightness to a lower setting does not increase the life of the lamp.)
language The language menu offers you any of five different languages supported by the
CDT-300. Classé have provided our international distributors with a software
tool that makes it possible for them to customize the translations to suit their
local customs and terminology, in an effort to ensure that the CDT-300’s
operation is as intuitive to use in every country as it is in our home country of
Canada.
colors The CDT-300 has the ability to change the color of the GUI menu system to
either blue, red, green or silver.
temporary display When playing a DVD, the CDT-300 displays the picture information on
its LCD touchscreen in a “preview” mode. This can be helpful in cueing up
material before sending the picture to the main display (saving your guests from
the otherwise inevitable FBI warnings). It is also a wonderful way of navigating
through DVD-Audio disc menu systems without having to turn on your main
video display simply to enjoy some music.
When you make use of any of the control functions of the CDT-300, the display
will change from its normal preview mode to display the user interface screens.
The temporary display setting determines how long this user interface remains
displayed before the touchscreen reverts to its usual preview mode.
34
Downloaded From DvDPlayer-Manual.com Classe Audio Manuals
System Setup
Pressing the menu button to the left of the LCD touchscreen, followed by
pressing the on screen system setup button, will bring you to a menu system
that gives you a wide range of control over how the CDT-300 works both on its
own and as a part of your overall system.
the system setup
menu system
There are four submenus that can be accessed from the system setup menu. Each
will be covered in turn.
audio setup The audio setup button gives you access to six controls pertaining to how your
DVD transport handles various audio details.
35
Downloaded From DvDPlayer-Manual.com Classe Audio Manuals
audio delay When a disc has been incorrectly authored, the audio can be out of sync with
the video. Audio delay allows you to compensate for this by inserting a delay
that repositions the audio in relation to the video and brings them into sync. The
delay is adjustable in 10ms steps and operates within a range of ± 200 ms.
Modern video displays make extensive use of video processing (as does the
CDT-300 itself ). This circuitry converts standard definition video (480i or 576i,
depending on your local broadcast standard) to a format that is compatible with
modern fixed matrix displays such as LCD, DLP or plasmas.
However, this conversion process takes some small amount of time, causing a
“lip sync” problem between the audio (which has not been delayed appreciably)
and the video (which has been delayed for processing). While some people are
more sensitive to this problem than others, anyone who perceives a consistent lag
between the audio and video will find it quite annoying.
The audio delay function of the CDT-300 addresses this by delaying the audio
by anywhere by up to 200 milliseconds. This range of adjustment should be
adequate to handle any video processing delay you might find in your system.
Note that the best use of this delay is to compensate for any delay introduced
by the CDT-300’s own video processing (assuming you are one of the ones who
are sensitive to this sort of thing). The CDT-300 can only delay audio coming
from itself, and has no control over (for example) broadcast television you may
be watching. If your television introduces enough video processing delay to be
noticeable, you would be better off using the audio delay feature of your A/V
preamplifier/processor (assuming it has this capability—which Classé processors
do have.)
digital output The digital outputs of the CDT-300 can be configured in any of three ways,
based on how you plan to use the transport:
• off — selecting this feature will only enable audio output via HDMI.
• raw — which passes along the native signal of whatever disc is playing,
whether that is PCM, Dolby Digital, DTS, or anything else. This setting
assumes that your external processor can handle anything you might send
its way.
• PCM stereo — if the soundtrack you are playing contains multichannel
information, it will be “downmixed” to a two-channel PCM signal that
would be compatible with stereo playback, or further processing with
Dolby Pro Logic II or DTS Neo:6 (as examples).
36
Downloaded From DvDPlayer-Manual.com Classe Audio Manuals
video setup Taking full advantage of the CDT-300’s extensive video capabilities is simple.
Three menus will take care of everything.
video standard These settings are usually preset for the geographic market in which you
purchase the CDT-300. However, should you need to change the output of the
CDT-300 to conform with a different standard, your choices are:
• NTSC/PAL/native — either choose the broadcast standard for your area,
or set the CDT-300 to play the disc in its native format. This last option
requires that you have a suitable multistandard display that can handle
both NTSC and PAL.
• IRE 7.5 or 0 — the “video setup” in North America assumes that black
is reproduced at a video level of 7.5 IRE units, while most of the rest of
the world assumes that video black is represented by a video level of 0 IRE
units. The CDT-300 can operate either way; you should pick the standard
common to your area for compatibility with the rest of your video sources.
• Extended Black — the CDT-300 offers a choice between PC (extended
black) and CE black levels. Use Extended Black to pass “blacker than
black” video when connected to a Consumer Electronic display (not a PC
monitor.)
37
Downloaded From DvDPlayer-Manual.com Classe Audio Manuals
aspect ratio You have three choices for the way widescreen movies will be displayed on your
television. The choice should be determined by the capabilities of your television
as well as your personal preference.
• 4:3 — If you have a 4:3 display and prefer to have it filled at all times, the
CDT-300 will look for an available 4:3 version of the movie on any disc
you insert, and play that version.
• 16:9 — If you have a modern, widescreen display that support different
aspect ratios (including an anamorphic mode), select the 16:9 option.
Doing so passes the contents of the disc to your television without
addressing the aspect ratio. In effect, you are telling the CDT-300 that the
television will be responsible for handling the aspect ratio duties.
• letterbox — If you have a 4:3 display, but prefer to see widescreen movies
in their original form, the CDT-300 can create a “letterbox” version of the
movie for you within the 4:3 frame of your television. This will result in
black bars above and below the picture, but will show you all of the picture
as the director and cinematographer originally framed it.
resolution The CDT-300 has the ability to “upconvert” standard definition DVDs to higher
display rates that are more suitable for HDTV displays. Note that this capability
exists only through its HDMI outputs.
You can select from among the following video display rates:
• auto selection — If you use the HDMI digital interface between the
CDT-300 and your display, the two components will automatically
negotiate the optimal resolution for your display device. The auto selection
capabilities of the CDT-300 apply only to the HDMI output.
• sdtv 480/576 interlaced — 480i (60 Hz) is the standard in NTSC
countries; 576i (50 Hz) is standard in PAL countries.
• sdtv 480/576 progressive— 480p (60 Hz) is the deinterlaced version of
the standard for NTSC countries; 576p (50 Hz) is the deinterlaced version
of the standard in PAL countries.
• hdtv 720 progressive — at 720 by 1280 pixels, this is the most common
rate for plasma displays and many LCD displays, and the second-most
common HD broadcast standard. It is shown at 50 Hz in PAL countries,
and at 60 Hz in NTSC countries.
• hdtv 1080 interlaced — the 1080i standard is the most commonlybroadcast HDTV format in use today, at 1080 by 1920 pixels (interlaced).
• hdtv 1080 progressive — available only through the HDMI output,
1080p is the highest-quality HDTV standard. It displays 1080 by 1920
pixels per frame.
edge enhancement Select this feature when an increase in picture sharpness is desired.
38
Downloaded From DvDPlayer-Manual.com Classe Audio Manuals
color space
• Auto: automatically optimizes color space for your display.
• RGB 4: 4: 4: select this feature if you require your DVD transport to
output Pluge.
• Ycrcb 4:2:2: Chroma upsampling by 1/2
• Ycrcb 4:4:4: Chromo upsampling by 1/1
preference The DVD standard supports multiple soundtracks and languages, all on the
same disc. This versatility can make playing a DVD more complicated than you
might like. By establishing your preferences, the CDT-300 will be able to select
the right soundtrack and language without you having to search through menus.
audio format Many DVDs have multiple soundtracks, in different formats. You can state your
preference (assuming it is available) by pressing the audio format button.
• automatic — selects the “best” available soundtrack automatically.
Preference is given to soundtracks with a greater number of discrete
channels (e.g., 5.1 rather than 2.0).
• PCM — if you prefer uncompressed digital audio, even if it means fewer
channels, select the PCM option.
• Dolby 5.1 — states a preference for 5.1 channel Dolby Digital
soundtracks if they are available.
• Dolby stereo — indicates a preference for soundtracks intended to be
reproduced via Dolby Pro Logic or Dolby Pro Logic II decoding matrix.
• DTS — when selected, the CDT-300 will automatically play the DTS
(Digital Theater Systems) soundtrack, if one is available.
audio language You can also set a preference for the spoken language used in the soundtrack
being played. Automatic defers to the default soundtrack on the disc itself. If
you prefer, you can insist that the CDT-300 play an English, French, German,
Spanish, or Italian soundtrack (assuming one is available).
subtitle language Similarly, you can establish a preference for the language used in the subtitles.
Your choices are English, French, German, Spanish, or Italian.
CD autoplay When this button is highlighted, the transport will automatically start playback
when a CD is inserted.
39
Downloaded From DvDPlayer-Manual.com Classe Audio Manuals
navigation Historically, navigating within a CD and a DVD has worked differently.
Specifically, the “fast forward” and “rewind” functions on a CD required you
to press and hold the button during the scanning process. By contrast, the same
action on a DVD required only a button click — in fact, additional button
clicks would accelerate the rate at which the scanning would occur.
If you want to have all discs operate as per the DVD way of doing things, select
latching as your navigation preference.
If you prefer the CD way of doing things, choose non-latching instead.
If you want the CDT-300 to behave like a CD player when playing a CD, and
like a DVD when playing a DVD, choose adaptive.
parental control The CDT-300 includes a set of parental controls, similar to what you may have
on your cable or satellite TV service.
• The set password button allows you to set a four-digit numeric password,
which will be required to play any disc that exceeds the rating you select.
• The set rating button gives you a list of eight ratings, with the
corresponding movie ratings listed (e.g., level 6 is the same as an R-rated
movie). The level you select here determines the maximum rating that can
be played without the password being entered. (Note that this button is
only enabled after you have set a password.)
• The block unrated button prevents unrated movies from playing without
the password.
• The enable control button enables the parental control feature of the
CDT-300.
40
Downloaded From DvDPlayer-Manual.com Classe Audio Manuals
Updating Your Unit
From time to time Classé designs new software that will enhance your
component’s performance. Updating your unit with the latest software is a
matter of downloading a file from the Classe website (www.classeaudio.com) so
it is worth ensuring that your component is fully updated.
Details of the software your DVD transport is running can be found on the
Version Information Screen. This screen is accessed by pressing the Info button
on the remote control followed by Version Info on the LCD touchscreen, or by
pressing the Menu button beside the LCD touchscreen, then selecting Status
from the touchscreen menu, followed by Version Info.
The Version Info screen displays the Version Number of the software your unit
is running. The latest software is always on the Classé website, so if the Software
Version Number on your Version Info screen is lower than the Software Version
Number posted on the Classe website, then you should consider updating your
unit.
Simple update instructions are posted on the Classe website, together with
release notes and the software itself, so it is very easy to update your component
and make it perform to its maximum potential.
41
Downloaded From DvDPlayer-Manual.com Classe Audio Manuals
Troubleshooting
In general, refer any service problems to your Classé dealer. Before contacting
your dealer, however, check to see if the problem is listed here. If it is, try the
suggested solutions. If none of these solves the problem, contact your Classé
dealer.
1
My disc is skipping.
3 Gently clean the disc itself using a damp, soft cloth, wiping along
the radius of the disc rather than around the circumference.
(Cleaning discs in the manner minimizes the chance of damaging
the disc.)
3 The disc itself may already be damaged. Try several other discs, to
see whether the problem is widespread or limited to a particular
disc.
2
There is no sound and the Standby LED is not lit.
3 Ensure the transport is plugged into the AC mains, and that the
AC mains are operating normally.
3 Check that the main power switch on the rear of the unit is on.
3 Your display may be set to timeout, and the CDT-300 may
simply be in pause or stop. Touch the screen to reactivate it so
you can see the state of the unit, or simply press the Play key on
the remote control.
3 Unplug the unit for at least thirty seconds and then plug it in
again; try powering it up. (Sometimes a brownout or short-term
loss of power might require a restart.)
3 Verify that the AC mains is not out of range. The unit will
automatically attempt to protect itself from improper AC mains
voltages by not powering up.
3 If none of these solutions work, please consult your Classé dealer
for assistance. There are no user-serviceable parts inside your
unit.
3.
A disc was inserted, but the machine rejected it and asked for
another disc to be inserted.
3 Check that the disc is compatible with your unit. The CDT-300
will play CD Audio, DVD-Video, DVD-Audio, MP3, WMA,
Video-CD and S-VCD discs.
3 Ensure that the disc surface is clean, and try reinserting it.
3 Check that the label side of the CD is facing up.
4.
The disc is spinning but there is no sound in one or both
channels.
3 Check that both interconnect cables are properly connected
between the outputs of the CDT-300 and the inputs of your
preamplifier.
3 Ensure that the preamplifier/amplifier units being used are
properly configured. (You may need to consult those units’
owner’s manuals for more information.)
42
Downloaded From DvDPlayer-Manual.com Classe Audio Manuals
5.
The screen shows an error message and the Eject button does
not eject the disc (or the transport shows some other
anomalous behavior).
3 Press the Standby button so the screen dims and the blue light
goes on.
3 Using the rear panel power switch, turn off the unit for at least
thirty seconds. Then turn the power back on and press Standby
to restart the unit.
6.
The IR remote control seems not to function.
3 Ensure that there are no obstacles between the IR remote and the
IR sensor (located to the right of the Mute button).
3 If the batteries are weak, replace them with fresh ones.
43
Downloaded From DvDPlayer-Manual.com Classe Audio Manuals
Care & Maintenance
To remove dust from the cabinet of your DVD transport, use a feather duster or
a lint-free soft cloth. To remove dirt and fingerprints, we recommend isopropyl
alcohol and a soft cloth. Dampen the cloth with alcohol first and then lightly
clean the surface of the transport with the cloth. Do not use excessive amounts
of alcohol that might drip off the cloth and into the transport.
Caution!
At no time should liquid cleaners be applied directly to
the transport, as direct application of liquids may result
in damage to electronic components within the unit.
44
Downloaded From DvDPlayer-Manual.com Classe Audio Manuals
Specifications
All specifications are accurate at the time of printing. Classé reserves the right to
adjust specifications without notice.
Formats supported
CD, CD-R, CD-RW, DVD Audio, DVD Video,
VCD, SVCD, MP3, WMA, DVD-R, DVD+R,
DVD-RW, DVD+RW
Audio outputs
Coax S/PDIF 1 x RCA, AES/EBU 1 x XLR,
Optical 1 x Toslink
Video outputs
HDMI, Component (progressive scan),
S-Video, Composite
Internal Scaling
480i (via all video outputs),
480p (via component and HDMI)
720p/1080i/1080p (via HDMI)
Power consumption
55W
Mains voltage
determined by the needs of country for which
the unit was manufactured; cannot be reset by dealer or user
Overall dimensions
Width: 17.5” (445mm)
Depth: 16.5” (419mm)
Height: 4.75” (121mm)
Net weight
26 lbs (12 kg)
Shipping weight
35 lbs (16 kg)
For more information, see your Classé dealer, or contact:
Classé Audio
5070 François Cusson
Lachine, Quebec
Canada H8T 1B3
Telephone +1 (514) 636-6384
FAX
+1 (514) 636-1428
Internet:
http://www.classeaudio.com
email:
[email protected]
Classé and the Classé logo are trademarks of Classé Audio Inc. of Lachine, Canada. All rights reserved.
i-Command™ is a trademark of Equity International, Inc. All rights reserved.
AMX® is a registered trademark of AMX Corporation of Richardson, TX. All rights reserved.
Crestron™ is a trademark of Crestron Electronics, Inc. of Rockleigh, NJ. All rights reserved.
45
Downloaded From DvDPlayer-Manual.com Classe Audio Manuals
Dimensions
ʣǰää»
{Îӓ“
ÊÓ°™ä»
Ç{““
ÊÓ°™ä»
Ç{““
46
Downloaded From DvDPlayer-Manual.com Classe Audio Manuals
Downloaded From DvDPlayer-Manual.com Classe Audio Manuals
Classé Audio
5070 François Cusson
Lachine, Quebec
Canada H8T 1B3
+1 (514) 636-6384
+1 (514) 636-1428 (fax)
http://www.classeaudio.com
email: [email protected]
North America: 1 800 370 3740
email: [email protected]
Europe: 44 (0) 1903 221 700
email: [email protected]
Asia: (852) 2790 8903
email: [email protected]
All Others: +1 514 636 6394
email: [email protected]
Copyright © 2007 Classé Audio, Inc. Printed in Canada.
V 1.9
Downloaded From DvDPlayer-Manual.com Classe Audio Manuals
100107