Elation Design LED 36MH, 36 User manual

Elation Design LED 36MH, 36 User manual
Design LED 36MH
Elation Professional
4295 Charter Street
Los Angeles, Ca 90058
www.elationlighting.com
Rev. 1/26/07
Design LED 36MH™
Contents
1.
General Information……………………………………………………………………… 3
a. Introduction………………………………………………………………………. 3
b. Unpacking………………………………………………………..…………..… 3
c.
Customer Support…………………………………………….………………… 3
d. Warranty Registration……………………………………………………..…… 4
e. Discharge Lamp Warning……………………………………………………… 4
2.
Safety Instructions………………………………………………………........…………. 6
3.
Features…………………………………………………………………………………… 8
4.
General Guidelines………………………………………………………………………. 9
5.
Lamp Installation…………………………………………………………………………. 10
a. Lamp installation…………………………………………………….………….. 10
b. Lamp optimization……………………………………………………..…………11
6.
Mounting and Installation………………………………………………………….……. 13
a. Mounting Positions……………………………………………………………… 13
b. Mounting Points…………………………………………………………………. 14
c.
7.
Securing………………………………………………………………………….. 15
Understanding DMX……………………………………………………………………... 16
a. DMX Connections………………………………………………………………. 16
b. DMX Terminator…………………………………………………………………. 17
c.
3-Pin to 5-Pin Conversion……………………………………………………….18
d. DMX Addressing………………………………………………………………… 18
8.
Display Indicators……………………………………………………………………….. 20
9.
Fixture Menu……………………………………………………………………………… 21
a. Menu functions………………………………………………………………….. 23
10. DMX Channel Traits…………………………………………………………………….. 39
a. DMX Channel Values…………………………………………………………… 40
11. Error Codes………………………………………………………………………………. 45
12. Cleaning and Maintenance……………………………………………………………… 48
13. Warranty…………………………………………………………………………………... 49
14. Photometric Data………………………………………………………………………… 51
15. Gobo Patterns……………………………………………………………..……………... 52
16. Dimensional Drawings………………………………………………….……………….. 53
17. Circuit Schematic………...………………………………………………………………. 54
18. Technical Specifications…………………………………………...………….………… 55
©Elation Professional®
2
Design LED 36MH™
Design LED 36MH™
1. GENERAL INFORMATION
INTRODUCTION: Congratulations, you have just purchased one of the most innovative and
reliable lighting fixtures on the market today! The Design LED 36MH™ has been designed to
perform reliably for years when the guidelines in this booklet are followed. Please read and
understand the instructions in this manual carefully and thoroughly before attempting to
operate this unit. These instructions contain important information regarding safety during
use and maintenance.
UNPACKING: Thank you for purchasing the Design LED 36MH™ by Elation Professional®.
Every Design LED 36MH™ has been thoroughly tested and has been shipped in perfect
operating condition. Carefully check the shipping carton for damage that may have occurred
during shipping. If the carton appears to be damaged, carefully inspect your unit for damage
and be sure all accessories necessary to operate the unit have arrived intact. In the event
damage has been found or parts are missing, please contact our customer support team for
further instructions. Please do not return this unit to your dealer without first contacting
customer support at the number listed below.
CUSTOMER SUPPORT: Elation Professional® provides a customer support line, to provide
set up help and to answer any question should you encounter problems during your set up or
initial operation. You may also visit us on the web at www.elationlighting.com for any
comments or suggestions. For service related issue please contact Elation Professional®.
Service Hours are Monday through Friday 9:00 a.m. to 5:00 p.m. Pacific Standard Time.
Voice:
(323) 582-3322
Fax:
(323) 582-3108
E-mail:
Forum:
[email protected]
www.ElationLighting.com/forum
Warning! To prevent or reduce the risk of electrical shock or fire, do not expose this unit to
rain or moisture.
Caution! There are no user serviceable parts inside this unit. Do not attempt any repairs
©Elation Professional®
3
Design LED 36MH™
Design LED 36MH™
yourself, doing so will void your manufactures warranty.
Elation Encourages Recycling: Please do not discard the shipping carton in the trash. Please
recycle whenever possible.
WARRANTY REGISTRATION: The Design LED 36MH™ carries a two year (730 days)
limited warranty. Please fill out the enclosed warranty card to validate your purchase. All
returned service items whether under warranty or not, must be freight pre-paid and
accompany a return authorization (R.A.) number. The R.A. number must be clearly written on
the outside of the return package. A brief description of the problem as well as the R.A.
number must also be written down on a piece of paper and included in the shipping container.
If the unit is under warranty, you must provide a copy of your proof of purchase invoice. Items
returned without a R.A. number clearly marked on the outside of the package will be refused
and returned at customer’s expense. You may obtain a R.A. number by contacting customer
support at (323) 582-3322.
Never open this fixture while in use!
This device falls under protection-class 1. Therefore it is essential that the device be
grounded properly.
All electrical connections must performed by qualified personal.
Be sure the available voltage matches the voltage requirements of the unit.
Be sure the power cord is never crimped or damaged. If the power cord is damaged, replace
it immediately with a new one of similar power rating.
Always disconnect from main power before performing any type of service or any cleaning
procedure.
Only handle the power cord by the plug. Never pull out the plug by tugging the wire portion of
the cord.
Please be aware that damages caused by manual modifications to the device are not subject
to warranty.
©Elation Professional®
4
Design LED 36MH™
Design LED 36MH™
2. SAFETY INSTRUCTIONS
The Design LED 36MH™ is an extremely sophisticated piece of
electronic equipment. To guarantee a smooth operation, it is
important to follow the guidelines in this manual. The
manufacturer of this device will not accept responsibility for
damages resulting from the misuse of this fixture due to the
disregard of the information printed in this manual.
1. Always be sure that the fan and the air inlets remain clean and are never blocked.
Allow about 6” (15cm) between this fixture and other devices or a wall to allow for
proper cooling.
2. Never touch the fixture during normal operation. This can cause severe personal
injuries and/or damage to the fixture.
3. Be sure to unplug the DESIGN LED 36MH™ from the power outlet before
performing any service related issues.
4. Lamp Replacement; Allow at least 30 minutes after disconnecting main power
before you open the DESIGN LED 36MH™. To prevent personal injury, never touch
the lamp if you are not absolutely sure it has cooled.
5. Never look directly into the lamp beam. You risk injury to your retina, which may
induce blindness.
6. Be sure to track and record the lamp running time. The lamp should be changed at
the end of the specified lamp life, regardless of lamp output. You may also have to
change the lamp if it shows any deformations or damage. The same is with all glass
components, color filters, lenses and mirrors.
7. For safe operation, follow the Installation guide described in chapter two of this
manual. Operating the DESIGN LED 36MH™ without suited safety aids such as
safety cables or clamps can increase the risk of damage and/or personal injury.
8. Installation should only be performed by qualified and certified personal.
9. When mounting this fixture, use only the original rigging parts included with this
fixture. Any structural modification will void the original manufactures warranty and
©Elation Professional®
5
Design LED 36MH™
Design LED 36MH™
may increase the risk of damage and/or personal injury.
10. To reduce the risk of fire or shock, do not expose this fixture to rain or moisture.
11. Do not attempt to operate this fixture if the power cord has become damaged or
frayed.
Important Notice: Damages resulting from the disregard of safety and general user
instructions found in this user manual are not subject to any warranty claims.
Never touch the device during operation!
The housing may heat up
Never look directly into the light source,
as sensitive persons may suffer an epileptic shock.
©Elation Professional®
6
Design LED 36MH™
Design LED 36MH™
3. FEATURES
•
Pan 540˚ / Tilt 265°
•
Low power consumption
•
Minimal heat emission
•
Equipped with 36 one-watt LEDs: (12 red, 12 blue, 12 green)
•
High quality Luxeon LEDs manufactured by Lumileds, USA
•
100,000 hours RATED LEDs
•
Step-less, smooth RGB additive color mixing, 16.7 million colors (24bit)
•
Preprogrammed colored macros
•
Strobe-effect with a maximum flash rate of 18fps (white or color)
•
12 or 10 DMX-channel operation (16 or 8 bit operation)
•
Flicker-free operation for television and film
•
Brilliant light output
•
3 operation mode: DMX controlled, stand alone or sound activated (via internal
microphone)
•
Dimmer intensity from 0%~100%
•
Control board with 4-digit display and foil-keyboard
•
Digital display can be turned 180° to fit different installation position
•
RDMX (Remote DMX addressing from any DMX console)
•
Auto test for all functions
•
Automatic Pan/Tilt Correction
•
USITT DMX-512 Complaint
•
Value of each DMX-channel can be displayed
•
8 User Assignable Program Presets - Internal Program: Edit and save programs to the
incorporated EEPROM through the front control panel or external controller; you can
save a maximum of 48 scenes, and run the saved programs by using the “run” menu
on the front control panel
©Elation Professional®
7
Design LED 36MH™
Design LED 36MH™
4. GENERAL GUIDELINES
This fixture is a professional lighting effect designed for use on stage, in nightclubs, in
theatres, etc. Do not attempt operation or installation without a proper knowledge on how to
so.
This fixture was designed for indoor use only, use of this product outdoors will void all
warranties written or implied.
Although this fixture has not duty cycle, consistent operational breaks will ensure that the
fixture will function properly for many years to come.
Do not shake the fixture around. Avoid brute force when installing or operating the device.
When choosing an installation location, please be sure the fixture will not be exposed to
extreme heat, moisture, or dust. The minimum distance between the fixture and a wall or flat
surface should be at least .5 meter (about 1.5ft).
Always install the fixture with an appropriate safety cable. When installing the fixture in a
suspended environment always be to use mounting hardware no less than M10 x 25 mm,
also be sure the hardware is insert in the pre-arranged mounting holes in the “Omega” clamp
(see page 14).
When using the quick release “Omega” cam-lock system, be sure the four quick lock
fasteners are locked in the quick lock mounting points properly.
Do not attempt to operate this fixture until you have familiarized yourself with its functions.
Do not permit operation by persons not qualified for operating this type of theatrical fixture;
most damages are the result of operations by persons unfamiliar with this type of product.
©Elation Professional®
8
Design LED 36MH™
Design LED 36MH™
5. FIXTURE OVERVIEW
1) LED LENS ASSEMBLY – 36 One-watt Lumileds LED’s by Luxeon rated at 100,000
hours (12 red, 12 green, 12 blue).
2) LED MENU DISPLAY – Four segment LED menu display, details all menu functions.
3) MODE/ESC BUTTON – This button is used to access and exit the fixture’s on-board
menu system.
4) UP BUTTON – This button is used to scroll forward when navigating through the
fixture’s menu system.
5) DOWN BUTTON – This button is used to scroll backwards when navigating through
©Elation Professional®
9
Design LED 36MH™
Design LED 36MH™
the fixture’s menu system.
6) ENTER BUTTON – This button is used to select and confirm a menu function.
7) HEAD FAN ASSEMBLY – This fan is used to cool the internal temperature of the head
assembly.
8) BASE ASSEMBLY – The main base holds the majority of the electronics and logic
boards. The base also provides a means to securely mount the fixture to the floor or
ceiling.
9) DMX INPUT JACK – This 3-pin XLR jack is receives an incoming DMX signal from a
DMX controller.
10) DMX OUTPUT JACK – This 3-pin XLR jack sends a DMX signal to another DMX
fixture. For best results this jack should be terminated if it is the last fixture in a DMX
daisy chain (see DMX termination on page XX).
11) POWER CONNECTION – This cable provides main power to your fixture. Always be
sure to use a properly grounded power cable. If this cable ever becomes frayed or
damaged this cable should be replaced immediately by a qualified technician.
12) FUSE HOLDER – This housing holds a 2A/250v GMA fuse and is designed to protect
the electronics in the event of severer power fluctuations. Never defeat this fuse. In
the event of fuse failure, always be sure to replace with an exact match fuse unless
other wise specified by an authorized Elation Professional technician.
13) POWER SWITCH – This switch controls main power to the unit (if I have to tell you
that, you probably should not be using this fixture!).
14) TRANSPORT HANDLE – This fixture contains a build-in carrying handle be sure to
always transport this fixture by the handle and never by grasping the head or yoke
assembly.
15) OMEGA CLAMP – This system allows a quick and efficient means to secure a clamp
to the unit. To attach a clamp to the unit, attach a clamp that is rated to handle the
weight of the unit to your omega clamp. After a clamp has been attached to the omega
clamp, attach the cam locks to the designated position on the bottom of your unit.
Lock the cam locks into position by turning the wing nuts 90°.
16) SAFETY CABLE RIGGING POINT –The fixture provides a built-in rigging point for a
safety cable on the underside of the fixture, be sure to use this point and never secure
a safety cable to a carrying handle.
©Elation Professional®
10
Design LED 36MH™
Design LED 36MH™
6. MOUNTING AND INSTALLATION
Caution: For added protection mount the fixtures in areas outside of walking paths, seating
areas, or areas were the fixture might be reached by unauthorized personal.
Before mounting the fixture to any surface, make sure that the installation area can hold a
minimum point load of 10 times the device’s weight.
Fixture installation must always be secured with a secondary safety attachment, such as an
appropriate safety cable.
To avoid injury, never stand directly below the device when mounting, removing, or servicing
the fixture.
Refer to regulations BGV C1 (formerly VBG 70) and DIN VDE
0711-217 for proper installation in Europe
To ensure proper installation, only qualified staff should
attempt installation.
Mounting
The DESIGN LED 36MH™ is fully operational in two different mounting positions, hanging
upside-down from a ceiling, or set on a flat level surface (see illustration on next page). To
avoid internal damage to the unit, never mount the unit on its side in a permanent
installation as illustrated on the next page. This could cause excessive stress on the motors
and damage the unit. Be sure this fixture is kept at least 0.5m away from any flammable
materials (decoration etc.). Always use and install the supplied safety cable as a safety
measure to prevent accidental damage and/or injury in the event the clamp fails.
Be sure to complete all rigging and installation procedures before connecting the main power
cord to the appropriate wall outlet.
©Elation Professional®
11
Design LED 36MH™
Design LED 36MH™
Mounting points
Overhead mounting requires extensive experience, including amongst others calculating
working load limits, a fine knowledge of the installation material being used, and periodic
safety inspection of all installation material and the fixture. If you lack these qualifications, do
not attempt the installation yourself. Improper installation can result in bodily injury.
CAUTION!
Be sure all electrical connections are performed by a qualified
electrician.
©Elation Professional®
12
Design LED 36MH™
Design LED 36MH™
Clamp Mounting
The Design LED 36MH™ provides a unique mounting bracket assembly that integrates the
hanging yoke as well as the safety cable rigging point in one unit (see the illustration on next
page). When mounting this fixture to truss be sure to secure an appropriately rated clamp to
the hanging yoke using a M10 screw fitted through the center hole of the hanging yoke. As an
added safety measure be sure to attached at least one properly rated safety cable to the
fixture using on of the safety cable rigging point integrated in the bracket assembly
Securing the DESIGN LED 36MH™
Regardless of the rigging option you choose for your DESIGN LED 36MH™ always be sure
to secure your fixture with a safety cable. The fixture provides a built-in rigging point for a
safety cable on the hanging bracket as illustrated above (3). Be sure to only use the
designated rigging point for the safety.
©Elation Professional®
13
Design LED 36MH™
Design LED 36MH™
7. UNDERSTADING DMX
Data Cable (DMX Cable) Requirements (For DMX and Master/Slave Operation):
Your fixture and your DMX controller require a standard 3-pin XLR connector for data input
and data output (see figure below). Be sure to only use properly rated DMX cables for DMX
operation and not standrd audio cables. If you are constructing your own cables be sure to
use two conductor shielded digital cable rated at a 120 ohms (this cable can be purchased at
almost all professional sound and lighting stores). Your cables should be made with a male
and female 3-pin XLR connector on either end of the cable.
Please note; this is not the same as audio microphone cable. Audio cable has a
different resistance rating.
Be sure to follow the above figure when making your own cables. Do not use the ground lug
on the XLR connector. Do not connect the cable’s shield conductor to the ground lug or allow
the shield conductor to come in contact with the XLR’s outer casing. Grounding the shield
could cause a short circuit and erratic behavior.
©Elation Professional®
14
Design LED 36MH™
Design LED 36MH™
DMX-512 control connection
Connect the provided XLR cable to the female 3-pin XLR output of your controller and the
other side to the male 3-pin XLR input of the moving head (Please refer to the diagram on the
previous page). You can link multiple DMX fixtures together through DMX cables as
illustrated on the previous page. Always be sure to daisy-chain your in and out data
connections, never split or “Y” your DMX connections unless you are using an approved DMX
splitter such as the Elation Opto Branch 4™ or DMX Branch/4™.
DMX-512 connection with DMX terminator
Although a DMX line may operate normally without one, we always recommend the use of a
terminator on the last fixture to avoid erratic behavior. A terminator is a 120 ohm 1/4 watt
resistor that is connected between pins 2 and 3 of a male XLR connector (DATA + and DATA
-). A DMX Terminator is inserted in the female XLR connector of the last fixture in your DMX
chain. Using a cable terminator (Elation part number Z-DMX/T) will decrease the possibilities
of erratic behavior. In instances where a DMX splitter is used, you must be sure to terminate
all open lines. For example if using an Elation DMX Branch/4™ with four line outputs you
must be sure to 4 DMX terminators, one for each output.
5-Pin XLR DMX Connectors. Some manufactures use 5-pin XLR connectors for DATA
transmission in place of 3-pin. 5-pin XLR fixtures may be implemented in a 3-pin XLR DMX
©Elation Professional®
15
Design LED 36MH™
Design LED 36MH™
line. When inserting standard 5-pin XLR connectors in to a 3-pin line a cable adaptor must be
used, these adaptors are readily available at most electric stores. The following chart details
a proper cable conversion.
Fixture DMX addressing;
All fixtures should be given a DMX starting address when using a DMX controller, so the
correct fixture responds to the correct control signal. This digital starting address is the
channel number from which the fixture starts to “listen” to the digital control information sent
out from the DMX controller. The allocation of this starting DMX address is achieved by
setting the correct DMX address on the digital display located on the head of the fixture.
You can set the same starting address for all fixtures or a group of fixtures, or set different
address for each individual fixture. Be advised that setting all you fixtures to the same DMX
address will subsequently control all fixtures in the same fashion, in other words, changing
the settings of one channel will affect all the fixtures simultaneously.
If you set each fixture to a different DMX address, each unit will start to “listen” to the channel
number you have set, based on the quantity of control channels (DMX channels) of each
fixture. That means changing the settings of one channel will only affect the selected fixture.
In the case of the Design LED 36MH™, which is a 12 channel fixture(default setting), you
should set the starting DMX address of the first unit to 1, the second unit to 13 (12 + 1), the
third unit to 25 (12 + 13), and so on.
©Elation Professional®
16
Design LED 36MH™
Design LED 36MH™
Note: During start-up the Design LED 36MH™ will automatically detect whether a DMX data
signal is being received or not. If DMX data signal is being received, the display will show
"A.XXX" (XXX representing the actual DMX address). If the fixture is not receiving a DMX
signal the display will flash "A.XXX" (XXX representing the actual DMX address).
If your fixture is connected to a DMX controller and the display is flashing (not receiving a
DMX signal), please check the following:
-
The 3 PIN XLR plug (cable with DMX signal from controller) is not connected or is not
inserted completely into the DMX input jack.
-
The DMX controller is switched off or defective.
-
The DMX cable or connector is defective.
-
A DMX terminator has been inserted into the last fixture in your DMX chain.
©Elation Professional®
17
Design LED 36MH™
Design LED 36MH™
8. DISPLAY LED INDICATORS
The Design LED 36MH™ has two LED indicators on the display. These indicators are
designed to give a quick visual indication of the fixtures’ status. The illustration below details
the functionality of the LED indicators.
. .
DMX OK
Lamp on
.
NO DMX
Lamp on
.
NO DMX
Lamp off
DMX OK
Lamp off
The first LED indicators represents DMX signal:
• If the indicators is on a clean DMX signal is present
• If the indicator is off there is no DMX signal present
The second LED indicator represents lamp condition:
• If the indicator is on the lamp is struck and in working condition
• If the LED indicator is off the lamp has not struck, has been turned off, or is bad.
©Elation Professional®
18
Design LED 36MH™
Design LED 36MH™
9. FIXTURE MENU
On-Board System Menu: The DESIGN LED 36MH™ comes with an easy to navigate
system menu. This next section will detail the functions of each command in the system
menu.
LED Control Panel: The control panel located on the top, front of the fixture allows you to
access the main menu and make all necessary adjustments to the Design LED 36MH™.
During normal operation, tapping the “MODE/ESC” key once will access the fixture’s main
menu. Once in the main menu you can navigate through the different functions and access
the sub-menus with the Up and Down buttons. Once you reach a field that requires adjusting,
tap the ENTER button to activate that field and use the UP and Down button to adjust the
field. Tapping the Enter button once more will confirm your setting. Once a setting is saved
the LED will briefly readout PASS to confirm a new setting has been made and locked into
memory. You may exit the main menu at any time without making any adjustments by tapping
the MODE/ESC button.
MODE/ESC Button - To access the main menu locate the MODE/ESC button on the front of
the unit. Press this button to activate the system menu. Tap the UP button until you reach the
function you wish to change. When you reach the function you wish to change tap the ENTER
button once to select that menu function. When a function is selected the menu will begin to
flash, use the UP or DOWN button to change the function. Once your changes are made tap
the ENTER button yet again to lock the change in the system menu. To exit without making
any changes tap the MODE/ESC button.
Default settings shaded.
0
ADDR
A001~A511
1
2
TEST
AUDI
T-01~T-XX
MSTR
Indicate the staring DMX address.
Set all slave units to A001 in
Master-Slave mode.
Automatically test all function
Runs fixture as a master unit for
audio Master-Slave mode.
©Elation Professional®
19
Design LED 36MH™
Design LED 36MH™
ALON
3
4
RESE
ALL
ON/OFF
TIME
SCAN
LIFE
LAMP
ON/OFF
0000~9999
0000~9999
ON/OFF
5
6
7
RPAN
RTLT
FINE
CLMP
ON/OFF
ON/OFF
ON/OFF
8
DISP
VALU
D ON
FLIP
9
SPEC
RDMX
SPOT
DFSE
FEED
VER
10 EDIT
STEP
SCXX
RUN
Runs fixture as a single unit for
Stand-Alone operation.
Resets all motors and returns fixture
to the home position.
Resets only the pan and tilt motors.
Displays the total fixture running time.
Displays a lamps running time.
Clear lamp running time.
Reverses the pan movements.
Reverses the tilt movements.
Changes modes between 16 bit and
8 bit operation.
D–XX D-00 (DXXX)
LED display will detail the DMX value
of each channel during normal
operation.
ON/OFF
Turns off LED display after 2 minutes
of non-use
ON/OFF
This function will reverse the LED
display by 180˚ for hanging operation.
ON/OFF
Allows a user to change the DMX
address remotely from a DMX
console.
ON/OFF
Lamp optimization.
ON/OFF
Resets all the fixture functions to
factory settings.
ON/OFF
Pan and tilt feedback (error
correction) on/off
V1.0~V9.9
Displays the fixture’s current software
version
Sets the amount of steps in
S–01 ~S–48
the user program.
C–01
0 1 XX (00~FFH) Edit each of the channel
~
~
settings (values) for the
C-12
12 XX (00~FFH) selected scene.
Adjust the hold time of
TIME
T – XX (01~FFH) each scene in the user
program.
Allows the programmer to
edit the user program via
CEDT
ON/OFF
any
external
DMX
controller.
ON/OFF
Program test
©Elation Professional®
20
Design LED 36MH™
Design LED 36MH™
Main Menu Functions
1. ADDRESS MENU
- AOO1 - A511 (Value) - This is where you set the fixtures DMX address.
Setting/Changing the DMX Address
After applying power to the DESIGN LED 36MH™ the LED will display the fixture’s
current DMX address immediately after the reset sequence. If the fixture is not receiving
a DMX signal the display will flash continuously. To set or adjust a DMX address, please
follow the procedure below:
1. Switch on the DESIGN LED 36MH™ and wait for the fixture reset process to
finished.
2. Press the Mode/Esc button to access the main menu. Toggle through the menu by
pressing the Up and Down buttons until the display shows A001. Tap the enter
button to make changes to the address, the current three digit address will
immediately begin to flash.
3. While the current three-digit address is flashing, use the Up and Down buttons to
adjust the address. Lock your new address into the unit’s memory by pressing the
Enter button. After the new address has been successfully stored into the fixture’s
memory the LED will briefly readout PASS.
The DMX address is non-destructible and will remain in the fixture’s memory even when
power to the fixture has been switched off. Memory is backed-up and retained by an internal
power source with a five year shelf life.
2. TEST MENU
- T-01 - T-XX (Test) - Tests the functions of each channel. There are 12 DMX
channels and all except channels can be tested. To enter the test menu follow the procedure
below:
1. Access the main menu.
2. Tap the UP button until “TEST” is displayed, press ENTER.
3. The display will show T-01. You can now press the up button and test the different
©Elation Professional®
21
Design LED 36MH™
Design LED 36MH™
channels. For example: If you press the up button until “T-03” is displayed, the unit will
test the color channel, changing the color one by one and show the rainbow effect
with different speeds.
4. Press MODE/ENTER or EXIT to exit.
3. AUDIO MENU -
MSTR (Master) – Runs fixture in audio mode as a master unit in Master-Slave mode.
ALON (Alone) – Runs fixture in audio mode as a single unit in Stand-Alone operation.
MSTR - This feature is used to run the internal preset programs in AUDIO mode in a
Master/Slave configuration. Follow the procedure below for Master-Slave operation:
1. Access the main menu.
2. Tap the UP or DOWN button until “AUDI” is displayed, press ENTER.
3. Tap the UP or DOWN button until “MSTR” is displayed, press ENTER.
4. Press MODE/ESC to return to the main menu.
5. Set the DMX address to 001 for all slave units.
ALON – This feature is used to run the internal preset programs in AUDIO mode in a
Stand-Alone configuration (single fixture mode). Follow the procedure below for
Stand-Alone operation:
1. Access the main menu.
2. Tap the UP or DOWN button until “AUDI” is displayed, press ENTER.
3. Tap the UP or DOWN button until “ALON” is displayed, press ENTER.
4. Press MODE/ESC to return to the main menu.
4. RESE (RESET) MENU -
ALL - Resets all the motors in the unit.
SCAN - Resets the Pan and Tilt motors.
©Elation Professional®
22
Design LED 36MH™
Design LED 36MH™
ALL
- When you activate this reset function, the fixture will begin to reset all motors.
1. Access the main menu.
2. Tap the UP button until “RESE” is displayed, press ENTER.
3. Tap the UP button until “ALL” is displayed, press ENTER.
4. The display will show “ON/OFF”. Press the UP button to select “ON” to reset the
color motor.
5. Press ENTER to confirm
6. Press MODE/ESC to return to the main menu.
SCAN
- When you activate this reset function, the fixture will only reset the Pan and Tilt
motors.
1. Access the main menu.
2. Tap the UP button until “RESE” is displayed, press ENTER.
3. Tap the UP button until “SCAN” is displayed, then press ENTER to confirm.
4. The display will show “ON/OFF”. Press the UP button to select “ON” to reset the
color motor. Press ENTER to confirm.
5. Press MODE/ESC to return to the main menu.
5. TIME MENU -
LIFE - Displays the fixtures total running time.
LAMP - Displays the lamp running time.
CLMP - Clears the lamp running time.
LIFE
- With this function you can display the total running time of the fixture.
1. Access the main menu.
2. Tap the UP button until ”TIME” is displayed, press ENTER.
©Elation Professional®
23
Design LED 36MH™
Design LED 36MH™
3. Tap the UP button until “LIFE” is displayed, press ENTER.
4. Press MODE/ESC to return to the main menu.
LAMP
- With this function you can display the running time of the lamp.
1. Access the main menu.
2. Tap the UP button until ”TIME” is displayed, press ENTER.
3. Tap the UP button until “LAMP” is displayed, press ENTER.
4. Press MODE/ESC to return to the main menu.
CLMP
- With this function you can clear the running time of the lamp. Note: Please
clear the lamp time every time you replace the lamp.
1. Access the main menu.
2. Tap the UP button until “TIME” is displayed, press ENTER.
3. Tap the UP button until “CLMP” is displayed, press ENTER.
4. Press MODE/ ENTER, the display will show “ON/OFF”.
5. Press the UP button to select “ON” to activate this function, or “OFF” to
deactivate this function.
6. Press ENTER to confirm.
7. Press MODE/ESC to return to the main menu.
6. RPAN MENU
- This menu function will reverse the mirror PAN movements.
1. Access the main menu.
2. Tap the UP button until “RPAN” is displayed, press ENTER.
3. The display will show “ON/OFF”.
4. Press the UP button to select “ON” to activate this function, or “OFF” to deactivate
this function.
5. Press ENTER to confirm.
6. Press MODE/ESC to return to the main menu.
©Elation Professional®
24
Design LED 36MH™
Design LED 36MH™
7. RTLT MENU
- This menu function will reverse the mirror TILT movements.
1. Access the main menu.
2. Tap the UP button until “RTLT” is displayed, press ENTER.
3. The display will show “ON/OFF”.
4. Press the UP button to select “ON” to activate this function, or “OFF” to deactivate
this function.
5. Press ENTER to confirm.
6. Press MODE/ESC to return to the main menu.
8. FINE MENU
- This menu item switches between 16 bit (fine) and 8 bit (coarse) modes. When
this function is turned on the fixture will operate in 16 bit (fine) mode. When functioning in
16 bit mode the fixture will use 16 DMX channels, when the 16bit function is turned off the
fixture will use 14 DMX channels. To access the Fine menu follow the procedure below:
1. Access the main menu.
2. Tap the UP button until “FINE” is displayed, press ENTER.
3. The display will show “ON/OFF”.
4. Press the UP button to select “ON” to activate this function, or “OFF” to deactivate
this function.
5. Press ENTER to confirm.
6. Press MODE/ESC to return to the main menu.
9. DISPLAY MENU
- This menu function will control the various on-board display features.
VALU – This function will display the DMX value of each channel as it is
adjusted through the use of a DMX console.
1. Access the main menu.
©Elation Professional®
25
Design LED 36MH™
Design LED 36MH™
2. Tap the UP button until “DISP” is displayed.
3. Press ENTER, the display will show “VALU”.
4. Press ENTER, once again “d-00” will be displayed.
5. Press ENTER to confirm.
6. Press MODE/ESC to return to the main menu.
D ON – This function will turn the display off after the has gone two seconds
without any menu activity.
1. Access the main menu.
2. Tap the UP button until “DISP” is displayed.
3. Press ENTER, the display will show “VALU”.
4. Tap the UP button until ”D-ON” is displayed and tap the ENTER button.
5. Press the UP button to select “ON” to activate this function, or “OFF” to deactivate
this function.
6. Press ENTER to confirm.
7. Press MODE/ESC to return to the main menu.
FLIP – This function will reverse the display readout buy 180˚.
1. Access the main menu.
2. Tap the UP button until “DISP” is displayed.
3. Press ENTER, the display will show “VALU”.
4. Tap the UP button until ”FLIP” is displayed and tap the ENTER button.
5. Press the UP button to select “ON” to activate this function, or “OFF” to deactivate
this function.
6. Press ENTER to confirm.
7. Press MODE/ESC to return to the main menu.
10. SPEC MENU – This menu option access all the special functions listed below.
RDMX - Allows DMX address to be changed via and external DMX controller.
DFSE (Default) - Resets the unit to all default settings.
FEED - This function turn the DMX correction feature “ON” (default) or “OFF.”
©Elation Professional®
26
Design LED 36MH™
Design LED 36MH™
VER (Version) - Displays the software version.
RDMX
– This function allows the DMX address to remotely be adjusted from a DMX
console. This setting requires special settings for both the controller and the fixture.
RDMX is on by default. Follow the procedure listed below to access the RDMX functions:
Fixture Settings:
1. Access the main menu.
2. Tap the UP button until “SPEC” is displayed, press ENTER.
3. Tap the UP button until “RDMX” is displayed, press ENTER.
4. The display will show “ON/OFF.”
5. Press the UP button to display “ON” to activate this function, or “OFF” to
deactivate this function.
6. Press ENTER to confirm.
7. Press MODE/ESC to return to the main menu.
Controller Settings:
1. Set the DMX value of channel 1 to a value of 7.
2. Set the DMX value of channel 2 to a value of 7 or 8. When channel 2 is set to "7"
you can adjust the starting address between 1 and 255. When set to "8" you can
adjust the starting address between 256 and 511.
3. Use channel 3 to set your desired DMX starting address. For example: If you
want to set the starting address to 57, set channel 1 to a value of “7,” set channel 2
to a value of “7” and use channel 3 to set your address to 57 by selecting a channel
value of 57. Example 2: If you want to set the starting address to 420, set channel
1 to a value of “7,” channel 2 to "8" and channel 3 to "164" (256+164=420).
4. Wait for approximately 20 seconds for the unit to complete the address
reset function.
DFSE
- With this function you can restore the factory default settings of the fixture. All
©Elation Professional®
27
Design LED 36MH™
Design LED 36MH™
settings will be set back to the default values. Any edited scenes will be lost. When
restoring the factory settings the unit must be set to the address that the unit was in when
you started editing. When you confirm this function, the fixture will begin to reload
the original factory settings.
1. Access the main menu.
2. Tap the UP button until “SPEC” is displayed, press ENTER.
3. Tap the UP button until “DFSE” is displayed, press ENTER.
4. The display will show “ON/OFF.”
5. Press the UP button to display “ON” to activate this function, or “OFF” to
deactivate this function.
6. Press ENTER to confirm.
7. Press MODE/ESC to return to the main menu.
FEED
- Use this function to activate the pan/tilt error correction.
1. Access the main menu.
2. Tap the UP button until “SPEC” is displayed, press ENTER.
3. Tap the UP button until “FEED” is displayed, press ENTER.
4. The display will show “ON/OFF.”
5. Press the UP button to display “ON” to activate this function, or “OFF” to
deactivate this function.
6. Press ENTER to confirm.
7. Press MODE/ESC to return to the main menu.
VER
- Use this function to display the Software version of the unit.
1. Access the main menu.
2. Tap the UP button until “SPEC” is displayed, press ENTER.
3. Tap the UP button until “VER” is displayed, press ENTER.
4. The display will show “V-1.0,” the display may also show, “V-2.0,” “V-9.9” etc.
5. Press ENTER or MODE/ESC to exit.
©Elation Professional®
28
Design LED 36MH™
Design LED 36MH™
11. EDIT MENU
- This menu item allows you to write a program into the fixture’s internal memory
(EEPROM) via the control panel or via an external DMX controller.
STEP (S-01 - S-48) – This set the total amount of scenes in the user program. There is a
maximum of 48 scenes available.
SCXX (SC01 – SC48) - These are the scenes that are stored in your program. There are a
total of 48 scenes. C-01 ~ C-12 (Channel 1 ~ Channel 12) – Represents the total fixture
channels for each scene that can be edited.
TIME (Time) - Running time of the entire program.
CEDT - Edit program using a external controller.
RUN – Program test mode.
CEDT- Records scenes automatically from any external DMX controller and stores them
inside the fixtures built-in memory. These scenes can then be recalled without the use of
an external controller.
1. Access the main menu.
2. Tap the UP or DOWN buttons until “EDIT” is displayed, then press ENTER.
3. Tap the UP or DOWN buttons until “REC” is displayed, then press ENTER.
4. After entering the REC function the display will read “RE.XX,” where as “XX”
represents the scene number in the internal memory to which the scene will be
stored.
5. Press the UP or DOWN buttons to select the desired scene number.
6. When you reach the scene number you wish to store the scene to, press ENTER
to confirm and lock the scene into the fixture’s memory.
7. Press MODE/ESC to return to the main menu.
STEP
- With this function you can program the number of steps in your individual
©Elation Professional®
29
Design LED 36MH™
Design LED 36MH™
Program.
1. Access the main menu.
2. Tap the UP button until “EDIT” is displayed, press ENTER.
3. Tap the UP button until “STEP” is displayed, press ENTER.
4. The display shows “S-01,” this indicates the first step of your program. You can
call up to 48 scenes in “Run.” For example; if “S-05” is displayed, it means that
the scene will “RUN” the first 5 scenes you saved in “Edit.”
5. Press ENTER to save and MODE/ESC to exit.
SC01
- This function allows you to choose the total number of scenes in your internal
program.
1. Access the main menu.
2. Tap the UP button until “EDIT” is displayed, press ENTER.
3. Tap the UP button until “SC01” is displayed.
4. The display indicates “SC01,” this stands for the first scene of your program. You
may recall up to 48 scenes. For example, if you choose “SC05,” and then select
the “Run” function, the first 5 scenes you saved in “Edit” mode will run.
5. Press ENTER to save and MODE/ESC to exit.
Editing procedure 1: Using the control board only.
1. Access the main menu.
2. Tap the UP button until “EDIT” is displayed and press ENTER.
3. The display will show “SC-01”, this stands for the scene number. For example,
“SC-01” is displayed, it means you will be editing scene 1, press ENTER. You can
change the scene number by tapping the UP button.
4. Press ENTER, the display will show “C-01,” this represents the channel number. If
“C-01” is displayed, you will be editing the fixture’s channel 1 value of the
selected scene, press ENTER. You can change the channel number by tapping
the UP button.
5. The display will show the DMX value for the channel that is being edited. It will be
displayed as “11XX,” it stands for Channel 11 of the editing scene, the DMX value
©Elation Professional®
30
Design LED 36MH™
Design LED 36MH™
is “XX.”
6. Adjust the DMX value by tapping the UP button, until you get the expected effect
for this channel.
7. Press ENTER to enter the editing of the other channels of the scene.
8. Repeat steps 5-8, until you finish setting all the DMX values for all the channels of
this scene, each scene can have 16 channels maximum.
9. Once all the channels are completed, the display will begin to flash “TIME,” this
indicates the time needed to run this scene.
10. Press ENTER to edit the time needed, the display shows “ TXXX ” , “ XXX ”
represents the time needed to run this scene. For example, “T002” means scene
1 needs 0.4 seconds to run, “T-15” means this scene needs 3.0 seconds to run.
Note: “XX” is always 0.2 seconds not one second.
11. Adjust the time needed by tapping the UP button.
12. Press ENTER to save the settings for the scene you are editing, the display will
change to the next scene automatically.
13. Repeat steps 3-12 to edit other scenes, you can edit and save 48 scenes
maximum.
14. Press MODE/ESC to exit and save your edited scene into the fixtures internal
memory. The number of steps can be defined under “EDIT” and the scenes can
be called up under “Run.” To run the scenes see page 30.
Editing procedure 2: Using an external controller.
1.
Call up the first scene in your controller now.
2.
Select “SC01” by pressing the UP or DOWN buttons.
3.
Press MODE/ESC, the display shows “SC01”.
4.
Press MODE/ESC, the display shows “C-01”.
5.
Select "CEDT" by pressing the UP or DOWN buttons.
6.
Press MODE/ESC, the display shows "OFF".
7.
Press UP, the display will read "ON".
8.
Press MODE/ESC, the display shows "SC02". You successfully downloaded
the first scene.
9.
Adjust the Step-time as described above.
©Elation Professional®
31
Design LED 36MH™
Design LED 36MH™
10. Call up the second scene in your controller now.
11. Repeat steps 5-11 until all desired scenes are downloaded.
12. Press MODE/ESC to exit. The number of steps can be defined under “STEP”
and the scenes can be called up under “RUN.”
RUN
- This function allows you to “RUN” the user-installed program. You can set the
number of steps under Step (S-01- S-48). You can edit the individual scenes under Edit.
1. Access the main menu.
2. Tap the UP button until “EDIT” is displayed, press ENTER.
3. Tap the UP button until “RUN” is displayed, press ENTER.
4. “AUTO” is displayed. If you press the UP button it will show “SOUN”. Select which
one you want to activate, and press ENTER.
5. Press UP, to select “ALON” or “NAST”. Which mean stand alone, and
master/slave mode.
6. Select a mode, and press ENTER to confirm.
7. Press MODE/ESC to return to the main menu.
©Elation Professional®
32
Design LED 36MH™
Design LED 36MH™
10. DMX CHANNEL TRAITS
The chart below details the channel layout for 12 DMX channels (default).
In 8bit mode the “Pan Fine” and “Tilt Fine” channels are not used, thus converting the fixture
into a 10-channel DMX fixture.
CHANNEL 1: Pan Movement (max. 540˚)
CHANNEL 2: 16bit Pan Movement (pan fine)
CHANNEL 3: Tilt Movement (max. 265°)
CHANNEL 4: 16bit Tilt Movement (tilt fine)
CHANNEL 5: Speed Control (Pan/Tilt movement, blackout selection)
CHANNEL 6: Rainbow Control (Built-in color macros)
CHANNEL 7: Red Control
CHANNEL 8: Green Control
CHANNEL 9: Blue Control
CHANNEL 10: Strobe Control (0~13Hz, Variable, Random, Pulse)
CHANNEL 11: Special (Auto program control and motor reset)
CHANNEL 12: Dimmer Control
©Elation Professional®
33
Design LED 36MH™
Design LED 36MH™
DMX channel function and values (12 Channel Mode):
Channel 1 - PAN movement 8bit :
Channel 2 – Pan fine
Channel 3 - TILT movement 8bit :
Channel 4 – Tilt fine
Channel 5 - Speed pan/tilt movement:
0-225
Max to min speed
226-235
Blackout by movement
236-245
No function
246-255
No function
Channel 6 - Rainbow:
0-7
No function
8-220
Rainbow colors
221-255
Crossfading colors from slow to fast
Channel 7 - Red :
0-255
Red (0-Black, 255-100% Red)
Channel 8 - Green:
0-255
Green (0-Black, 255-100% Green)
Channel 9 - Blue:
0-255
Blue (0-Black, 255- 100% Blue)
Channel 10 – reset, internal programs:
Normal
0-79
80-84
All motor reset
85-87
Scan motor reset
88-99
No function
100-119
Internal program 1
120-139
Internal program 2
140-159
Internal program 3
160-179
Internal program 4
180-199
Internal program 5
©Elation Professional®
34
Design LED 36MH™
Design LED 36MH™
200-219
220-239
240-255
Channel 11 - Strobe:
0
1-95
96-127
128-159
160-191
192-223
224-255
Internal program 6
Internal program 7
Auto program by music
No function (shutter open)
Strobe effect slow to fast
No function (shutter open)
Pulse effect in sequences
No function (shutter open)
Random strobe effect slow to fast
No function (shutter open)
Channel 12 - General dimming (option 1)
0-255
Dimming (1%-100%)
©Elation Professional®
35
Design LED 36MH™
Design LED 36MH™
DMX channel function and values (10 Channel Mode):
Channel 1 - PAN movement 8bit :
Channel 2 - TILT movement 8bit :
Channel 3 - Speed pan/tilt movement:
0-225
Max to min speed
226-235 Blackout by movement
236-245 No function
246-255 No function
Channel 4
0-7
8-220
221-255
- Rainbow:
No function
Rainbow colors
Crossfading colors from slow to fast
Channel 5 - Red :
0-255
Red (0-Black, 255-100% Red)
Channel 6 - Green:
0-255
Green (0-Black, 255-100% Green)
Channel 7 - Blue:
0-255
Blue (0-Black, 255- 100% Blue)
Channel 8 – reset, internal programs:
No function
0-79
80-84
All motor reset
85-87
Scan motor reset
88-99
No function
100-119 Internal program 1
120-139 Internal program 2
140-159 Internal program 3
160-179 Internal program 4
180-199 Internal program 5
200-219 Internal program 6
220-239 Internal program 7
240-255 Auto program by music
©Elation Professional®
36
Design LED 36MH™
Design LED 36MH™
Channel 9 - Strobe:
0
No function (shutter open)
1-95
Strobe effect slow to fast
96-127 No function (shutter open)
128-159 Pulse effect in sequences
160-191 No function (shutter open)
192-223 Random strobe effect slow to fast
224-255 No function (shutter open)
Channel 10 - General dimming (option 1)
0-255
Dimming (1%-100%)
©Elation Professional®
37
Design LED 36MH™
Design LED 36MH™
11. ERROR CODES:
When power is applied, the unit will automatically enter a “reset/test” mode. This mode brings
all the internal motors to a home position. If there is an internal problem with one or more of
the motors an error code will flash in the display in the form of “XXer” were as XX will
represent a function number. For example, when the display shows “02Er,” it means there is
some type of error with the channel 2 motor. If there are multiple errors during the start-up
process they will all flash in the display. For example: if the fixtures has errors on channel 1,
channel 2, and channel 5 all at the same time, you will see the error message “01Er”, “02Er,”
and ”05Er” flash repeated 5 times.
If an error does occur during the initial start-up procedure the fixture will self-generate a
second reset signal and try to realign all the motors and correct the errors, if the error persist
after a second attempt a third attempt will be made.
If after a third attempt all the errors have not been corrected the fixture will make the following
determinations: 1) 3 or more errors - The fixture cannot function properly with three or more
errors therefore the fixture will place itself in a stand-by mode until subsequent repairs can be
made. 2) Less than 3 errors - The fixture has less than 3 errors, therefore most other
functions will work properly. The fixture will attempt to operate normally until the errors can be
correct by a technician. The errors in question will remain flashing in the display as a reminder
of internal errors.
01Er – PAN movement error:
The yoke is not located in the default position after start-up or after a reset command. This
message will appear after a fixture reset if the pan-yoke’s magnetic-indexing circuit
malfunctions (sensor failed or magnet is missing) or there is a stepper motor failure (defective
motor or a defective motor IC drive on the main PCB).
03Er – TILT movement error:
The head is not located in the default tilt position after start-up or after a reset command. This
message will appear after a fixture reset if the tilt magnetic-indexing circuit malfunctions
©Elation Professional®
38
Design LED 36MH™
Design LED 36MH™
(sensor failed or magnet is missing) or there is a stepper motor failure (defective motor or a
defective motor IC drive on the main PCB).
©Elation Professional®
39
Design LED 36MH™
Design LED 36MH™
12. CLEANING AND MAINTENANCE
Please refer to the following points during normal inspection:
1. Be sure all screws and fasteners are securely tightened at all times. Lose screws may
fall out during normal operation resulting in damage or injury as larger parts could fall.
2. There must not be any deformations on the housing, color lenses, rigging hardware
and rigging points (ceiling, suspension, trussing). Deformations in the housing could
allow for dust to enter into the motor assemblies. Damaged rigging points or
unsecured rigging could cause the unit to fall and serious injure a person.
3. All mechanical parts and motors should not show any traces of serious wear and
should rotate freely.
4. Electric power supply cables must not show any damage, material fatigue or
sediments. Never remove the ground prong from the power cable.
Further instructions depending on installation and usage have to be adhered to by a skilled
installer and any safety problems should be addressed before attempting operation.
We recommend frequent cleaning of the device; this will ensure operational longevity and
crisp light output. When cleaning, please use a moist, lint-free cloth. Never use alcohol or
solvents.
There are no user serviceable parts inside this. Please refer all other service related issues to
an authorized Elation service technician.
Should you decide to service the fixture yourself please order genuine Elation parts directly
from Elation.
©Elation Professional®
40
Design LED 36MH™
Design LED 36MH™
13. 2-YEAR LIMITED WARRANTY
A. Elation Professional® hereby warrants, to the original purchaser, Elation Professional®
products to be free of manufacturing defects in material and workmanship for a period of two
years, (730 days) from the date of purchase. This warranty shall be valid only if the product is
purchased within the United States of America, including possessions and territories. It is the
owner’s responsibility to establish the date and place of purchase by acceptable evidence, at
the time service is sought.
B. For warranty service, send the product only to the Elation Professional® factory. All
shipping charges must be pre-paid. If the requested repairs or service (including parts
replacement) are within the terms of this warranty, Elation Professional® will pay return
shipping charges only to a designated point within the United States. If the entire instrument is
sent, it must be shipped in its original package. No accessories should be shipped with the
product. If any accessories are shipped with the product, Elation Professional® shall have no
liability what so ever for loss of or damage to any such accessories, nor for the safe return
thereof.
C.
This warranty is void if the serial number has been altered or removed; if the product is
modified in any manner which Elation Professional® concludes, after inspection, affects the
reliability of the product; if the product has been repaired or serviced by anyone other than the
Elation Professional® factory unless prior written authorization was issued to purchaser by
Elation Professional®; if the product is damaged because not properly maintained as set
forth in the instruction manual.
D. This is not a service contract, and this warranty does not include maintenance, cleaning
or periodic check-up. During the period specified above, Elation Professional® will replace
defective parts at its expense, and will absorb all expenses for warranty service and repair
labor by reason of defects in material or workmanship. The sole responsibility of Elation
Professional® under this warranty shall be limited to the repair of the product, or replacement
thereof, including parts, at the sole discretion of Elation Professional®. All products covered
by this warranty were manufactured after January 1, 1990, and bare identifying marks to that
©Elation Professional®
41
Design LED 36MH™
Design LED 36MH™
effect.
E.
Elation Professional® reserves the right to make changes in design and/or
improvements upon its products without any obligation to include these changes in any
products theretofore manufactured.
F.
No warranty, whether expressed or implied, is given or made with respect to any
accessory supplied with products described above. Except to the extent prohibited by
applicable law, all implied warranties made by Elation Professional® in connection with this
product, including warranties of merchantability or fitness, are limited in duration to the
warranty period set forth above. And no warranties, whether expressed or implied, including
warranties of merchantability or fitness, shall apply to this product after said period has
expired. The consumer’s and or Dealer’s sole remedy shall be such repair or replacement as
is expressly provided above; and under no circumstances shall Elation Professional® be
liable for any loss or damage, direct or consequential, arising out of the use of, or inability to
use, this product.
G. This warranty is the only written warranty applicable to Elation Professional® Products
and supersedes all prior warranties and written descriptions of warranty terms and conditions
heretofore published.
©Elation Professional®
42
Design LED 36MH™
Design LED 36MH™
14. PHOTOMETRIC DATA:
©Elation Professional®
43
Design LED 36MH™
Design LED 36MH™
15. DIMENSIONAL DRAWINGS:
©Elation Professional®
44
Design LED 36MH™
Design LED 36MH™
17. TECHNICAL SPECIFICATIONS
Power supply
Power consumption
Power Consumption
Fuse protection
_98VAC, 50Hz;□120VAC, 50Hz;□208VAC, 50Hz;
□220VAC, 50Hz;□230VAC, 50Hz;□240VAC, 50Hz; or
□ 98VAC,60Hz; □ 120VAC,60Hz; □ 208VAC,60Hz;
220VAC,60Hz;□230VAC,60Hz;□240VAC,60Hz;
135w
□
120V = 2A/250V, GMA (5x20mm fine-wire fuse)
220V = 2A/250V, GMA (5x20mm fine-wire fuse)
Lamp
36 x 1w Lumileds LEDs
Type
100,000 Hrs Rated
Life time
Color
12 x Red LEDs ~ 12 Green LEDs ~ 12 Blue LEDs
Strobe / Dimmer
Strobe-effect with variable speed 1 - 18 flashes per second
Continuously mechanical dimmer 0 - 100%
DMX Channels
12 (16bit – default) or 10 (8bit – user selectable)
Drive
Standard DMX-512, 3 pole XLR; [+] = Pin 3
[-] = Pin 2
[Ground] = Pin 1.
Starting DMX [001].
Pan / Tilt
Pan- movement
540° in max. 2.0 seconds, 16 bit resolution
Tilt- movement
265° in max. 1.5 seconds, 16 bit resolution
Weights and measures
Dimensions
29cm (W) x 28.2cm (L) x 34.7cm (H) ~ Head vertical
Weight (net)
9.5Kgs / 20Lbs
Please Note: Specifications and improvements in the design of this unit and this
manual are subject to change without any prior written notice.
©Elation Professional®
45
Design LED 36MH™
Design LED 36MH™
Elation Professional
4295 Charter Street
Los Angeles, CA. 90058
323-582-3322 / 323-582-3108 fax
www.ElationLighting.com /
[email protected]
©Elation Professional®
46
Design LED 36MH™
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement