CM Valustar 2401, 2402, 2413, 2412, 2403, 2404, 2405, 2406, 2414, 2407, 2408, 2409, 2410, 62401, 62402, 62413, 62412, 62403, 62404, 62405, 62406, 62414, 62407, 62408, 62409, 62410 Electric Chain Hoist Operating, Maintenance & Parts Manual

Electric Chain
24761
Operating, Maintenance
& Parts Manual
TM
Rated Loads
1/4 through 2-Tons
250 through 2000 kg.
Follow all instructions and warnings for
inspecting, maintaining and operating this hoist.
The use of any hoist presents some risk of personal injury or
property damage. That risk is greatly increased if proper
instructions and warnings are not followed. Before using this
hoist, each operator should become thoroughly familiar with
all warnings, instructions, and recommendations in this manual.
Retain this manual for future reference and use.
Forward this manual to the hoist operator.
Failure to operate the equipment as directed in the manual
may cause injury.
Before using the hoist, fill in the information below. Refer to
the hoist identification plate.
Model Number ____________________________________
Serial Number______________________________________
Purchase Date ____________________________________
Voltage ____________________________________________
Rated Load ________________________________________
®
624-U
i
CM HOIST PARTS AND SERVICES ARE AVAILABLE IN THE UNITED STATES AND IN CANADA
As a CM Hoist user, you are assured of reliable repair and parts services through a network of Master Parts Depots and
Service Centers that are strategically located in the United States and Canada. These facilities have been selected on the
basis of their demonstrated ability to handle all parts and repair requirements promptly and efficiently.
Below is a list of the Master Parts Depots in the United States and Canada. To quickly obtain the name of the U.S. Service
Center located nearest you, call (800) 888-0985. Fax: (716) 689-5644. In the following list, the Canadian Service Centers are
indicated.
UNITED STATES MASTER PARTS DEPOT
CALIFORNIA
OTTO SYSTEMS, INC.
12010 Bloomfield Ave.
Santa Fe Springs, CA 90670
562/462-1612 or 800/596-7392
Fax 562/462-1617
or
7656 Las Positas Road
Livermore, CA 94551
925/245-8800 or 800/508-6886
Fax 925/245-8804
COLORADO
MATERIALS HANDLING EQUIPMENT CO.
1740 W. 13th Ave.
Denver, CO 80204
303/573-5333
Fax 303/893-3854
GEORGIA
ACE INDUSTRIES, INC.
6295 McDonough Drive
Norcross, GA 30093
770/441-0898 or 800-733-2231
Fax 800/628-3648
ILLINOIS
JOHN SAKASH COMPANY INC.
700 Walnut Street
Elmhurst, IL 60126
630/833-3940
Fax 630/833-9830
INDIANA
HORNER ELECTRIC COMPANY, INC.
1521 East Washington Street
Indianapolis, IN 46201
317/639-4261
Fax 317/639-4342
IOWA
VM HOIST & CRANE SERVICES
PO Box 440
450 Highway 151
Walford, IA 52351
319/846-6040
Fax 319/846-6045
KANSAS
INDEPENDENT ELECTRIC MACHINERY
4425 Oliver Street
Kansas City, KS 66106
913/362-1155 or 800/833-2610
Fax 913/904-3330
LOUISIANA
BEERMAN PRECISION, INC.
PO Box 6018
Metairie, LA 70009
504/207-6000
Fax 504/207-6044
MASSACHUSETTS
ABEL DISTRIBUTORS, INC.
50 Parker Street, Unit 2
Newburyport, MA 01950
978/463-0700
Fax 978/463-5200
NEW JERSY
SHUPPER-BRICKLE EQUIPMENT CO.
PO Box 803
2394 Route 130, Suite C
Dayton, NJ 08810
732/438-3888
Fax 732/438-3889
NEW YORK
VOLLAND ELECTRIC EQUIPMENT CO.
75 Innsbruck Drive
Buffalo, NY 14227
716/656-9900
Fax 716/656-8899
NORTH CAROLINA
TEAM SESCO
PO Box 667489
2225 Freedom Drive
Charlotte, NC 28208
704/372-4832 or 800/487-3726
Fax 704/358-1098
OHIO
MAZZELLA LIFTING TECHNOLOGIES
21000 Aerospace Parkway
Cleveland, OH 44142-1072
440/239-7000 or 800/362-4601
Fax 440/239-7010
PENNSYLVANIA
AMICK ASSOCIATES, INC.
11 Sycamore Street
PO Box 529
Carnegie, PA 15106-0529
412/429-1212 or 800/445-9456
Fax 412/429-0191
RAM MOTORS & CONTROLS, INC.
5460-B Pottsville Pike, Docks 8-11
PO Box 748
Leesport, PA 19533
610/916-8000
Fax 610/916-7957
SOUTH CAROLINA
ENGINEERED SYSTEMS INC.
1121 Ducan-Reidville Road
Duncan, SC 29334
864/879-7438 or 800/879-7438
Fax 864/879-6428
TEXAS
ABEL EQUIPMENT CO., INC.
3710 Cavalier Drive
Garland, TX 75042
972/272-7706
Fax 972/272-6955
HYDRAULIC EQUIPMENT SERVICES, INC.
1021 North San Jacinto Street
Houston, TX 77002
713/228-9601
Fax 713/228-0931
WISCONSIN
TRESTER HOIST & EQUIPMENT, INC.
W136 N4863 Campbell Drive Suite #4
Menomonee Falls, WI 53051
262/790-0700 or 800/234-6098
Fax 262/790-1009
CANADIAN SERVICE CENTERS
ALBERTA
BENNETT & EMMOTT, LTD.
18131 118TH Avenue
Edmonton, Alberta T5S 1MB
403/454-9000
Fax 403/454-8990
**COLUMBUS McKINNON, LTD.
10311-174th Street
Edmonton, Alberta T5S 1H1
800/263-1997
Fax 403/486-6160
BRITISH COLUMBIA
FLECK BROTHERS, LTD.
4084 McConnel Court
Burnaby, British Columbia V5A 3N7
604/420-3535
Fax 604/421-8803
MANITOBA
KING’S ELECTRIC MOTORS, INC.
633 Tyne Avenue
Winnipeg, Manitoba R2L 1J5
204/663-5332
Fax 204/663-4059
NOVA SCOTIA
*W & A MOIR
95 Ilsley Ave.
Dartmouth, Nova Scotia B3B 1L5
902/468-7720
Fax 902/468-3777
ONTARIO
*R & W HOIST REPAIR, LTD.
790 Redwood Square
Units 5, 6, & 7
Oakville, Ontario L6L 6N3
905/825-5500
Fax 905/825-5315
*TORONTO ELECTRIC HOIST
SALES & SERVICE
9 Codeco Court
North York, Ontario M3A 1A1
416/386-0820
Fax 416/386-0821
*MASLACK SUPPLY, LTD.
488 Falconbridge Road
Sudbury, Ontario P3A 4S4
705/566-1270
Fax 705/566-4208
*COLUMBUS MCKINNON, LTD.
P.O. Box 1106
10 Brook Road, North
Cobourg, Ontario K9A 4W5
905/372-0153
Fax 905/372-3078
QUEBEC
*HERCULES SLING & CABLE
3800 Transcanada Highway
Pointe-Claire, Quebec H9R 1B1
514/428-5511
Fax 514/428-5555
*LEGER PALANS ET OUTILLAGES,INC.
7995-17th Ave.
Montreal, Quebec H1Z 3R2
514/376-3050
Fax 514/376-0657
* ARE ALSO MASTER PARTS DEPOTS
** MASTER PARTS DEPOT ONLY
ii
SAFETY PRECAUTIONS
Each Valustar Electric Hoist is built in accordance with the specifications contained herein and at the time of manufacture complied with our interpretation of applicable sections of the *American Society of Mechanical Engineers Code B30.16 “Overhead
Hoists,” the National Electrical Code (ANSI/NFPA 70) and the Occupational Safety and Health Act. Since OSHA states the
National Electrical Code applies to all electric hoists, installers are required to provide current overload protection and grounding
[on the branch circuit section] in keeping with the code. Check each installation for compliance with the application, operation
and maintenance sections of these articles.
The safety laws for elevators, lifting of people and for dumbwaiters specify construction details that are not incorporated into the
hoists. For such applications, refer to the requirements of applicable state and local codes, and the American National Safety
Code for elevators, dumbwaiters, escalators and moving walks (ASME A17.1). Columbus McKinnon Corporation cannot be
responsible for applications other than those for which CM equipment is intended.
L
!
*Copies of this standard can be obtained from ASME Order Department, 22 Law Drive, Box 2300, Fairfield, NJ 07007-2300, U.S.A.
THIS SYMBOL POINTS OUT IMPORTANT SAFETY INSTRUCTIONS WHICH IF NOT FOLLOWED
COULD ENDANGER THE PERSONAL SAFETY AND/OR PROPERTY OF YOURSELF AND
OTHERS. READ AND FOLLOW ALL INSTRUCTIONS IN THIS MANUAL AND ANY PROVIDED
WITH THE EQUIPMENT BEFORE ATTEMPTING TO OPERATE YOUR VALUSTAR HOIST.
L
!
WARNING
Improper operation of a hoist can create a potentially hazardous situation which, if not avoided, could result in death or
serious injury. To avoid such a potentially hazardous situation,
the operator shall:
1. NOT operate a damaged, malfunctioning or unusually
performing hoist.
2. NOT operate the hoist until you have thoroughly read
and understood this Operating, Maintenance and Parts
Manual.
3. NOT operate a hoist which has been modified (without
the manufacturer’s approval or without certification that it
is in conformity with ANSI/AMSE B30 volumes).
4. NOT lift more than rated load for the hoist.
5. NOT use hoist with twisted, kinked, damaged, or worn
load chain.
6. NOT use the hoist to lift, support, or transport people.
7. NOT lift loads over people.
8. NOT operate a hoist unless all persons are and remain
clear of the supported load.
9. NOT operate unless load is centered under hoist.
10. NOT attempt to lengthen the load chain or repair damaged load chain.
11. Protect the hoist’s load chain from weld splatter or other
damaging contaminants.
12. NOT operate hoist when it is restricted from forming a
straight line from hook to hook in the direction of loading.
13. NOT use load chain as a sling, or wrap load chain
around load.
14. NOT apply the load to the tip of the hook or to the hook
latch.
15. NOT apply the load unless load chain is properly seated
in the chain wheel(s) or sprocket(s).
16. NOT apply load if bearing prevents equal loading on all
load supporting chains.
17. NOT operate beyond the limits of the load chain travel.
18. NOT leave load supported by the hoist unattended
unless specific precautions have been taken.
19. NOT allow the load chain or hook to be used as an electrical or welding ground.
20. NOT allow the load chain or hook to be touched by a
live welding electrode.
21. NOT remove or obscure the warnings on the hoist.
22. NOT operate a hoist on which the safety placards or
decals are missing or illegible.
23. NOT operate a hoist unless it has been securely
attached to a suitable support.
L
!
24. NOT operate a hoist unless load slings or other
approved single attachments are properly sized and
seated in the hook saddle.
25. Take up slack carefully - make sure load is balanced and
load holding action is secure before continuing.
26. Shut down a hoist that malfunctions or performs unusually
and report such malfunction.
27. Make sure hoist limit switches function properly.
28. Warn personnel of an approaching load.
! CAUTION
L
Improper operation of a hoist can create a potentially hazardous situation which, if not avoided, could result in minor or
moderate injury. To avoid such a potentially hazardous situation, the operator shall:
1. Maintain a firm footing or be otherwise secured when
operating the hoist.
2. Check brake function by tensioning the hoist prior to
each lift operation.
3. Use hook latches. Latches are to retain slings, chains,
etc. under slack conditions only.
4. Make sure the hook latches are closed and not supporting any parts of the load.
5. Make sure the load is free to move and will clear all
obstructions.
6. Avoid swinging the load or hook.
7. Make sure hook travel is in the same direction as shown
on the controls.
8. Inspect the hoist regularly, replace damaged or worn
parts, and keep appropriate records of maintenance.
9. Use the hoist manufacturer’s recommended parts when
repairing the unit.
10. Lubricate load chain per hoist manufacturer’s
recommendations.
11. NOT use the hoist load limiting or warning device to
measure load.
12. NOT use limit switches as routine operating stops unless
allowed by manufacturer. They are emergency devices
only.
13. NOT allow your attention to be diverted from operating
the hoist.
14. NOT allow the hoist to be subjected to sharp contact
with other hoists, structures, or objects through misuse.
15. NOT adjust or repair the hoist unless qualified to perform such adjustments or repairs.
iii
HOIST SAFETY IS UP TO YOU...
1
! WARNING
L
CHOOSE THE RIGHT HOIST FOR THE JOB...
Choose a hoist with a capacity for the job.
Know the capacities of your hoists and the
weight of your loads. Then match them.
The application, the size and type of load,
the attachments to be used and the period of
use must also be taken into consideration in
selecting the right hoist for the job.
Remember the hoist was designed to ease
! WARNING
L
2
– DO NOT OPERATE DAMAGED OR MALFUNCTIONING HOIST.
– DO NOT OPERATE WITH TWISTED, KINKED OR DAMAGED
CHAIN.
service until repairs are made.
Under no circumstances should you operate a malfunctioning hoist.
Check chain for gouged, twisted, distorted
links and foreign material. Do not operate
hoists with twisted, kinked or damaged chain.
Load chain should be properly lubricated.
Hooks that are bent, worn or whose open-
! WARNING
L
ings are enlarged beyond normal throat
opening should not be used. If latch does not
engage throat opening of hook, hoist should
be taken out service.
Check for misphasing – hook travel should
correspond to control direction.
– DO NOT PULL AT AN ANGLE. BE SURE HOIST AND LOAD
ARE IN A STRAIGHT LINE.
USE HOIST PROPERLY
Be sure hoist is solidly held in
the uppermost part of the support
hook arc.
Be sure hoist and load are in a
straight line. Do not pull at an
angle.
Be sure load is hooked securely.
Do not tip load the hook. Do not
load hook latch. Hook latch is to
prevent detachment of load under
slack chain conditions only.
! WARNING
L
4
our burden and carelessness not only
endangers the operator, but in many cases,
a valuable load.
INSPECT
All hoists should be visually inspected
before use, in addition to regular, periodic
maintenance inspections.
Inspect hoists for operational warning
notices and legibility.
Deficiencies should be noted and brought
to the attention of supervisors. Be sure
defective hoists are tagged and taken out of
3
– DO NOT LIFT MORE THAN RATED LOAD.
LIFT PROPERLY
Do not lift co-workers with a hoist.
Make sure everyone is clear of the load
when you lift.
Do not remove or obscure operational
warning notices.
Do not use load chain as a sling.
Such usage damages the chain
and lower hook.
Do not operate with hoist head
resting against any object. Lift the
load gently. Do not jerk it.
– DO NOT LIFT PEOPLE OR LOADS
OVER PEOPLE.
5
MAINTAIN PROPERLY
CLEANING: Hoists should be kept clean
and free of dust, dirt, moisture, etc., which
will in any way affect the operation or safety of the equipment.
LUBRICATION: Chain should be properly
lubricated.
AFTER REPAIRS: Carefully operate the
hoist before returning it to full service.
VIOLATION OF ANY OF THESE WARNINGS LISTED MAY RESULT IN SERIOUS PERSONAL INJURY TO THE
OPERATOR OR NEARBY PERSONNEL BY RELEASED LOAD OR BROKEN HOIST COMPONENTS.
1
FOREWORD
This manual contains important information to help you properly install, operate and maintain your hoist for maximum performance, economy and safety.
Please study its contents thoroughly before putting your hoist into operation. By practicing correct operating procedures and by
carrying out the recommended preventive maintenance suggestions, you will experience long, dependable and safe service.
After you have completely familiarized yourself with the contents of this manual, we recommend that you carefully file it for future
reference.
The information herein is directed to the proper use, care and maintenance of the hoist and does not comprise a handbook on
the broad subject of rigging. Rigging can be defined as the process of lifting and moving heavy loads using hoists and other
information, we recommended consulting a standard textbook on the subject.
TABLE OF CONTENTS
SAFETY PRECAUTIONS
PAGE
Master Parts Depots . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .i
Do’s and Do Not’s . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .ii
Hoist Safety is Up To You . . . . . . . . . . . . . . . . . . . . . . . . .iii
Foreward . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1
GENERAL INFORMATION
Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2
CM Repair/Replacement Policy . . . . . . . . . . . . . . . . . . . .2
ACCESSORIES
Series 635 Low Headroom Trolley . . . . . . . . . . . . . . . . . .3
Series 635 Motor Driven Trolley . . . . . . . . . . . . . . . . . . . .3
Rigid Lug Suspension . . . . . . . . . . . . . . . . . . . . . . . . . . . .3
Chain Container . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3
INSTALLATION
Unpacking Information . . . . . . . . . . . . . . . . . . . . . . . . . . .3
Attaching Suspension . . . . . . . . . . . . . . . . . . . . . . . . . . . .4
Attaching Load Chain . . . . . . . . . . . . . . . . . . . . . . . . . . . .4
Installing Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . .4
Series 635 Low Headroom Trolley . . . . . . . . . . . . . . .4
Series 635 Motor Driven Trolley . . . . . . . . . . . . . . . . .6
Chain Container . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6
Power Supply and Electrical Connections . . . . . . . . . . . .6
Three-Phase Hoists . . . . . . . . . . . . . . . . . . . . . . . . . . .7
Checking for Adequate Voltage at Hoists . . . . . . . . .7
Checking for Twist in Load Chain . . . . . . . . . . . . . . . .8
OPERATING INSTRUCTIONS
General . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8
Hoist . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8
Hoist with Low Headroom Trolley . . . . . . . . . . . . . . . . . . .9
Hoist with Motor Driven Trolley . . . . . . . . . . . . . . . . . . . . .9
Safety Procedures . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9
INSPECTION
Procedures . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9
Frequent Inspections . . . . . . . . . . . . . . . . . . . . . . . . . .9,10
Periodic Inspections . . . . . . . . . . . . . . . . . . . . . . . . . .9,10
Preventive Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . .9
Hook Inspection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11
Protector . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11
Load Chain . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11
MAINTENANCE
Hoist Lubrication . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12
Electric Brake Adjustment . . . . . . . . . . . . . . . . . . . . . . .12
Exterior Finish . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12
Trouble Shooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13
Recommended Spare Parts . . . . . . . . . . . . . . . . . . . . . .12
Electrical Data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14
Wiring Diagrams . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17
ASSEMBLY
PAGE
Hook or Lug Suspension . . . . . . . . . . . . . . . . . . . . . . . .16
Centrifugal Mechanism . . . . . . . . . . . . . . . . . . . . . . . . . .16
Fasteners . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16
Lower Hook Block Pin . . . . . . . . . . . . . . . . . . . . . . . . . . .16
Removal and Installation of Load Chain . . . . . . . . . . . .17
Cutting Chains . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18
Testing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18
REPLACEMENT PARTS
Ordering Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . .18
Parts List and Exploded Views . . . . . . . . . . . . . . . . .19-25
LIST OF TABLES
1
2
3
4
5
Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2
Trolley Side Frame Spacing . . . . . . . . . . . . . . . . . . . . . . .7
Min. Frequent Inspections . . . . . . . . . . . . . . . . . . . . . . .10
Min. Periodic Inspections . . . . . . . . . . . . . . . . . . . . . . . .10
Electrical Data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14
LIST OF ILLUSTRATIONS
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
Series 635 Low Headroom Trolley . . . . . . . . . . . . . . . . . .3
Series 635 Motor Driven Trolley . . . . . . . . . . . . . . . . . . . .3
Rigid Lug Suspension . . . . . . . . . . . . . . . . . . . . . . . . . . . .3
Chain Container . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3
Suspension Assemblies . . . . . . . . . . . . . . . . . . . . . . . . . .4
Load Chain Attachment . . . . . . . . . . . . . . . . . . . . . . . . . .5
Series 635 Low Headroom Trolley . . . . . . . . . . . . . . . . . .6
Attaching Hoist to Trolley . . . . . . . . . . . . . . . . . . . . . . . . .6
Hook Inspection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11
Gaging Load Chain Wear . . . . . . . . . . . . . . . . . . . . . . . .11
Typical Wiring Diagrams . . . . . . . . . . . . . . . . . . . . . . . . .15
Hook Suspension . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16
Centrifugal Mechanism Assembly . . . . . . . . . . . . . . . . .16
Cutting Chain by Nicking . . . . . . . . . . . . . . . . . . . . . . . .18
Cutting Chain with Bolt Cutter . . . . . . . . . . . . . . . . . . . .18
Exploded View, Control Station . . . . . . . . . . . . . . . . . . . .22
Exploded View, Hoist . . . . . . . . . . . . . . . . . . . . . . . . .23-24
Exploded View, Series 635 Low Headroom Trolley . . . . .25
2
GENERAL INFORMATION
SPECIFICATIONS
The Valustar Electric Chain Hoist is a highly versatile materials
handling device that can be used to lift loads that are within
rated capacity. The mechanical features of these hoists
include an alloy steel lift wheel, overload device (Protector),
hardened steel chain guides, simple two stage gear reduction, lifetime lubrication, forged steel hooks and lightweight
aluminum frames. The electrical features include hoist-duty
motor, magnetic reversing contactor, rugged control station,
heavy-duty motor brake and control transformer (3 phase
units). Hoists are supplied with a rigid upper hook suspension
as standard. Table 1 summarizes the hoist’s specifications.
CM REPAIR/REPLACEMENT POLICY
any properly maintained hoist develops a performance problem, due to a material or workmanship defect, as verified by
CM, repair or replacement of the unit will be made to the
original purchaser without charge. This repair/replacement
policy applies only to Valustar Hoists installed, maintained
and operated as outlined in this manual, and specifically
excludes parts subject to normal wear, abuse, improper
installation, improper or inadequate maintenance, hostile
environmental effects and unauthorized repairs/modifications.
We reserve the right to change materials or design if, in our
opinion, such changes will improve our product. Abuse,
repair by an unauthorized person, or use of non-CM replacement parts voids the guarantee and could lead to dangerous
operation. For full Terms of Sale, see Sales Order
Acknowledgement. Also, refer to the back cover for
Limitations of Warranties, Remedies and Damages, and
Indemnification and Safe Operation.
All Columbus McKinnon (CM) Valustar Electric Chain Hoists
are inspected and performance tested prior to shipment. If
Table 1
Valustar Electric Chain Hoist Specifications
CODE
DC
CODE
MODEL
2401
2402
2413
2412
2403
2404
2405
2406
2414
2407
2408
2409
2410
62401
62402
62413
62412
62403
62404
62405
62406
62414
62407
62408
62409
62410
WB
WB
WE
WE
WF
WF
WH
WH
WJ
WL
WL
WR
WR
MAX. CAP. LIFTING SPEED MOTOR
(TONS)
F.P.M.
H.P.
1/4
1/4
1/2
1/2
1/2
1/2
1
1
1/2
1
1
2
2
16
16
8
8
16
16
8
8
32
16
16
8
8
1/4
1/4
1/4
1/4
1/2
1/2
1/2
1/2
1
1
1
1
1
MIN. HOOK
DISTANCE
POWER SUPPLY
NET WEIGHT
VOLTS/PHASE/HERTZ (POUNDS)
16-1/2"
16-1/2"
19-7/8"
19-7/8"
16-1/2"
16-1/2"
19-7/8"
19-7/8"
17-5/8"
17-5/8"
17-5/8"
24-1/2"
24-1/2"
115-1-60
230/460-3-60
230/460-3-60
115-1-60
115-1-60
230/460-3-60
115-1-60
230/460-3-60
230/460-3-60
115-1-60
230/460-3-60
115-1-60
230/460-3-60
51
61
72
62
53
68
69
78
105
109
106
129
126
Series 635 Low Headroom Trolley Specifications
MAX. CAP.
(TONS)
FOR USE WITH MODELS
ADJUSTABLE FOR S-BEAMS
TREAD DIA. OF
WHEELS (IN.)
MIN. RADIUS
CURVE (IN.)
1/4 to 1
2
WB, WE, WF, WH, WJ, WL
WR
4" X 7.7# TO 15" X 50#
6" X 12.5# TO 18" X 54.7#
3-1/8
4-3/4
24
24
Series 635 Motor-Driven Trolley Specifications
MAX. CAP.
(TONS)
1/4 to 2
FOR USE WITH MODELS
WB, WE, WF, WH, WJ,
WL, WR
POWER
SUPPLY
TRAVEL
SPEED (FPM)
MOTOR
H.P.
ADJUSTABLE
FOR S-BEAMS
MIN. RADIUS
CURVE (IN.)
115-1-60
230-3-60
or 460-3-60
75
1/4
6" x 12.5"
thru
15" x 50#
30
3
ACCESSORIES
Series 635 Low Headroom Trolley
These are manual push type trolleys designed for use with
the Valustar Electric Chain Hoists, and a rigid lug suspension
is required to attach the hoist to the trolley (see Figure 1).
The trolley is adjustable to operate on a range of American
Standard beams as indicated in Table 1, and it will also
operate on flat flanged beams.
Figure 3. Rigid Lug Suspension
Chain Container
This accessory is used to hold the slack chain, and it is supplied complete with mounting hardware and mounting
instructions. The chain container is recommended for those
applications where the slack chain would interfere with the
load. Chain containers can be furnished for units already in
use. When ordering, specify hoist model and lift.
Figure 1. Series 635 Low Headroom Trolley
Series 635 Motor Driven Trolley
The motor driven trolley is self-contained and supplied complete with controls and wiring, ready for attachment to any of
the Valustar Electric Hoists (see Figure 2). A rigid lug suspension is required to attach the hoist to the trolley, and
complete instructions are provided to electrically and
mechanically attach the hoist to the trolley. The trolley is
adjustable to operate on a range of American Standard
beams as indicated in Table 1, and it will operate on flat
flanged beams.
Figure 4. Chain Container
INSTALLATION
UNPACKING INFORMATION
When received, the hoist should be carefully inspected for
damage which may have occurred during shipment or handling. Check the hoist frame for dents or cracks, the external
cords for damaged or cut insulation, the control station for
cut or damaged enclosure, and inspect the load chain for
nicks and gouges. If shipping damage has occurred, refer to
the packing list envelope on the carton for claim procedure.
Before installing the hoist, make sure that the power supply
to which it will be connected is the same as that shown on
the nameplate located on the side of the hoist.
Note: To assure extra long life and top performance,
be sure to follow the load chain lubricating instructions on Page 12.
Figure 2. Series 635 Motor Driven Trolley
Rigid Lug Suspension
This suspension is required for attaching the hoist to the Low
Headroom or Motor Driven Trolley (see Figure 3). It must be
ordered separately with the hoist model and trolley type
specified.
4
Also, do not apply any type of lubricant to the threads of
these screws. Lubricating the threads will reduce the effort to
seat the screws and, as a result, tightening the screws to the
above recommended torque may break the screw, damage
the suspension adapter, strip the nuts and/or damage the
hoist frame.
ATTACHING LOAD CHAIN
Models WE, WH and WR
1. Suspend the hoist from an adequate support.
2. The hoist is shipped with the dead end of the load chain
temporarily positioned a few links from the end by a plastic tie (1) as shown in Figure 6. Do not remove this plastic
tie until the chain is secured.
Figure 5. Suspension Assemblies
1. Lug type (single reeved adapter) for use with Low
Headroom Trolley and Motor Driven Trolley.
2. Swivel hook type (double-reeved adapter).
3. Rigid Hook Type (single-reeved adapter).
4. 12 point suspension screws.
(Do not order parts by these numbers. See parts list.)
ATTACHING SUSPENSION
1. Remove the hook suspension from the carton and the two,
12 point suspension screws from the bag, see Figure 5.
The suspension for a double chain hoist (Models WE, WH
and WR) includes a dead end bolt and block for supporting the dead end of the load chain as shown in Figure 5.
2. Place the suspension in the recess on top of hoist. On
double chain hoist, the dead end block should project
through the bottom of hoist with the pin hole and slot
aligned to the underside of hoist as shown in Figure 6. It
may be necessary to lift the bolt head from the hex
recess in the suspension adapter, turn and reseat it, to
obtain this alignment. DO NOT CHANGE THE POSITION
OF THE DEAD END BLOCK ON THE BOLT. The pin hole
should clear the hoist frame by not more than 1/4" on
Models WE and WH and 7/16" on Model WR.
3. Insert the screws through the adapter and engage the selflocking nuts enclosed in the hoist. Screws will enter the
nuts freely except for the last 1/4" of travel during which the
resistance of the nut locking collar will be encountered.
4. Securely tighten the screws to the recommended seating
torque specified in the table below, using a 12 point socket which fits the head of the screw.
Model No.
WB, WE, WF
and WH
WJ, WL,
and WR
Screw Size
3/8-16 UNC-3A
Recommended
Seating Torque
30-45 Lb. Ft.
1/2-20 UNF-3A
40-80 Lb. Ft.
3. On Models WE and WH, insert the last link of the load
chain into the dead end block (2) and secure it with the
dead end pin, washer and cotter pin furnished with the
suspension. Remove the plastic tie (1) by cutting with a
pair of electrical pliers.
On Model WR, remove the plastic tie (1) by cutting with a
pair of electrical pliers. Slide the contact block up the
chain until it is against the bottom of the hoist and the
dead end block is projecting through the square opening
in the bottom of the block. Insert the last link of the load
chain, making sure there are no twists between the hook
block and the dead end block, into the dead end block.
Push the contact block up slightly and secure the load
chain to the dead end block using the dead end pin,
washer and cotter pin furnished with the suspension. The
dead end pin also supports the contact block.
4. Do not remove the ties from the load chain until after the
hoist is suspended from its permanent support or tract
system. Now, suspend the hoist from its permanent support or tract system. If the hoist is to be hung from a Low
Headroom Trolley or a Motor Driven Trolley, refer to the
trolley installation instructions.
INSTALLING ACCESSORIES
Series 635 Low Headroom Trolley
(See Figure 7)
! WARNING
L
Operating the trolley on a beam that has no rail stops may
allow the trolley to fall off the end of beam.
TO AVOID INJURY:
Install rail stops at each end of the beam on which the trolley
is to operate.
To attach the hoist to the trolley a lug suspension (Figure 3) is
required. The trolley and lug suspension are packed separately, and the hook suspension that is packed with the hoist
may be discarded. To install the lug suspension, follow the
instructions for attaching the suspension on this page.
! WARNING
L
To adjust the trolley to fit the beam properly, proceed as follows:
TO AVOID INJURY:
2. The number of spacers as given in Table 2 is nominally
correct, however, due to the variation in size encountered
on structural steel sections, it will be necessary in some
cases to vary the number used. Therefore, the distance
Using other than CM supplied high strength suspension
screws to attach the suspension adapter to the hoist may
cause the screws to break and allow the hoist and load to fall.
Use only the CM supplied suspension screws to attach the
suspension to the hoist and torque these screws to the recommended seating torque as specified above.
1. Arrange the side frames, load bracket, spacer washers
and nuts on the suspension bolts according to Figure 7
and Table 2. Do not assemble cotter pins to the bolts.
Note: special trolleys shown in chart require
special suspension bolts.
5
Figure 6. Load Chain Attachment
6
between the trolley trackwheel flanges and the beam
flange width should be measured to determine the exact
distribution of the spacer washers. The number of spacer
washers between side frames and load bracket should
be the same or differ only by one spacer to keep the hoist
hook centered under the beam.
Figure 8. Attaching Hoist to Trolley
L
! WARNING
An excessively worn beam flange may fail and allow the trolley
to fall from the beam.
TO AVOID INJURY:
Figure 7. Series 635 Low Headroom Trolley
Note: Due to the variations in beam flange
widths, it is suggested that the beam flange
width be measured to determine the exact distribution of spacer washers. The distance between
trackwheel flanges (dimension “X”) should be
1/8 to 3/16 inch greater than the beam flange
width for straight runway beams, and 3/16 to 1/4
inch greater than the beam flange width if runway system includes sharp curves. Also, the use
of other than CM supplied washers may result in
trackwheel to beam flange variations and thus
Table 2 will not apply.
3. Install the trolley on beam by sliding one side of frame out
far enough to allow the trackwheels to clear the beam
flange.
! WARNING
L
If CM’s washer spacing recommendations are not followed,
trolley may fall from beam.
TO AVOID INJURY:
Measure the actual beam flange on which the trolley is to
operate and use Table 2 to determine the arrangement of the
spacer washers for that flange width.
4. Draw the side frames together and assemble cotter pins.
5. With the trolley mounted on the beam, attach the hoist by
inserting the suspension lug into the trolley load bracket
and inserting the suspension pin through the load bracket
and suspension lug as shown in Figure 8. Secure the pin
using the socket head cap screw and lockwasher.
Periodically inspect the beam flange for wear. Replace beam if
flange is worn.
Series 635 Motor Driven Trolley
To attach the hoist to the trolley, a lug suspension (Figure 3)
is required. The trolley and lug suspension are packed separately, and the hook suspension that is packed with the hoist
may be discarded. To install the lug suspension, follow the
instructions for attaching the suspension on page 4. The
Motor Driven Trolley must be assembled and wired to the
hoist by the user per the manual packed with the trolley.
Chain Container
For installation instruction, refer to instruction sheet packed
with the chain container.
POWER SUPPLY AND ELECTRICAL
CONNECTIONS
All Hoists
The hoist should be connected to a branch circuit which
complies with the requirements of the National Electrical
Code and applicable local codes.
It is recommended, especially for a single phase hoist with a
one horsepower motor, that a line of adequate capacity be
run directly from the power supply to the hoist to prevent
having problems with low voltage and circuit overloads.
7. Now, refer to “Power Supply and Electrical Connections”
on this page and complete the hoist installation procedure.
For grounding of the hoist, the power cord includes a
grounding conductor (green wire). On a standard single
phase unit this cord is equipped with a three-prong plug. Be
sure that the receptacle opening which receives the longest
prong is properly grounded. Furthermore, the suspension
system on which the hoist is mounted should also be permanently grounded.
8. Then with a capacity load on hoist, operate trolley over
the entire length of runway or monorail system to be sure
that the adjustment and operation is satisfactory. On systems with curves, keep the rail edges at the curved sections lightly greased.
Before connecting the hoist to the power supply, check that
the power to be used agrees with that shown on the hoist
identification label. In addition, for a three phase, dual voltage unit, check the voltage shown on the tag attached to
power cord.
6. Thread the socket head cap screw and lockwasher into
load bracket and tighten securely.
7
Table 2
1-TON CAPACITY
NO. OF SPACERS
Trolley Side Frame Spacing
“X”
STANDARD
TROLLEYS
A
B
C
D
SPECIAL
TROLLEYS
FLANGE
WIDTH
2-5/8
3
3-3/8
3-5/8
4
4-5/8
5
5-1/4
5-1/2
5-5/8
6
6
6-1/4
7
7-1/8
7-1/4
7-7/8
8
2-TON CAPACITY
NO. OF SPACERS
A
B
C
D
10
9
8
7
6
4
3
2
1
1
0
1
2
3
4
6
7
8
9
9
0
1
2
3
4
6
7
8
8
9
10
9
8
7
6
4
3
2
2
1
5
4
0
5
6
9
5
6
9
4
3
1
A
B
C
D
8
7
6
4
3
3
2
1
0
0
1
2
4
5
5
6
7
8
0
1
2
4
5
6
7
7
8
8
7
6
4
3
2
1
1
0
8
5
5
4
2
1
2
5
5
6
8
9
1
4
5
5
8
8
8
5
4
4
1
1
Minimum Beam Radius 24" for all capacities. Dimension applies to minimum S-Beam and will vary with larger S-Beams.
The nominal hoist voltage rating corresponding to the voltage
range given on hoist identification label is:
Range
110-120
220-240
440-480
SINGLE SPEED UNITS
Nominal Volts
115
230
460
Three Phase Hoists
Changing the voltage connections on a single speed, three
phase dual voltage unit is easily accomplished by following
the instructions on the wiring diagram provided with the hoist.
Since the motor in a three phase hoist can rotate in either
direction, depending on the manner in which it is connected
to the power supply, the direction of hook movement must be
checked during the original installation and each time hoist is
moved to a new location.
1. Make temporary connections at the power supply.
±
2. Operate (UP) control in control station momentarily. If
hook raises, connections are correct and can be made
permanent.
3. If hook lowers, it is necessary to change direction by
interchanging the Red Lead and the Black Lead of the
hoist power cord at power supply. Under no circumstances should the internal wiring of control station or
hoist be changed to reverse hook direction. The wiring is
inspected and tested at the factory.
! WARNING
L
Allowing the hook block to run into the bottom of the hoist
when raising a load or allowing the loose end block to run into
the bottom of the hoist when lowering a load may break the
chain and allow the load to drop.
TO AVOID INJURY:
Do not allow the hook block or the loose end block to contact
the bottom of the hoist.
Checking for Adequate Voltage at Hoist
The hoist must be supplied with adequate electrical power in
order to operate properly. For proper operation, the voltage,
(measured at the end of the hoist power cord) must be as
indicated in the table below:
NOMINAL
POWER
SUPPLY
115-1-60
230-3-60
460-3-60
MINIMUM
RUNNING
VOLTAGE
104
198
396
MINIMUM
STARTING
VOLTAGE
98
–
–
Signs of Inadequate Electrical Power (Low Voltage) are:
• Noisy hoist operations due to brake and/or contactor
chattering.
• Dimming of lights or slowing of motors connected to the
same circuit.
• Heating of the hoist motor and other internal components,
as well as heating of the wires and connectors in the circuit feeding the hoists.
• Failure of the hoist to lift the load due to motor stalling.
• Blowing of fuses or tripping of circuit breakers.
8
Low voltage can also be caused by using an undersize
extension cord to supply power to the hoist. The following
chart should be used to determine the size wires in the
extension cord in order to minimize the voltage drop between
the power source and the hoist.
LENGTH OF
EXTENSION
CORD
Up to 50 feet
80 feet
120 feet
SINGLE-PHASE
HOISTS
MIN. WIRE SIZE
#14 AWG
#12 AWG
#10 AWG
THREE-PHASE
HOISTS
MIN. WIRE SIZE
#16 AWG
#16 AWG
#14 AWG
L
! WARNING
Failure to provide a proper power supply system for the hoist
may cause hoist damage and offers the potential for a fire.
TO AVOID INJURY:
Provide the hoist with a 20 amp. minimum, overcurrent protected power supply system per the National Electrical Code
and applicable local codes as instructed in this manual.
Remember, operation with low voltage can void the CM
repair/replacement policy. When in doubt about any of the
electrical requirements, consult a qualified electrician.
Note: Always disconnect the power from the power
supply system and lockout/tagout disconnecting
means before servicing the hoist.
WARNING
Working in or near exposed energized electrical equipment
presents the danger of electrical shock.
TO AVOID INJURY
Disconnect power and lockout/tagout disconnecting means
before removing cover or servicing this equipment.
Checking for Twist in Load Chain
Models WE, WH and WR
The best way to check for this condition is to run the lower
hook, without a load, up to within about 2” of hoist. If the
dead-end of the chain has been properly installed, a twist
can occur only if the lower hook block has been capsized
between the strands of chain. Reverse capsize to remove
twist.
The hoist is equipped with a Protector™ that is designed to
allow the intermediate gear to slip on an excessive overload.
An overload is indicated when the hoist will not raise the
load. Also, some clutching noise may be heard if the hoist is
loaded beyond rated capacity. Should this occur, immediately release the up
control to stop the operation of the hoist.
At this point, the load should be reduced to the rated hoist
capacity or the hoist should be replaced with one of the
proper capacity. When the excessive load is removed, normal hoist operation is automatically restored.
CAUTION: The Protector™ is susceptible to overheating and wear when slipped for extended periods. Under no circumstance should the clutch be
allowed to slip for more than a few seconds.
Due to the above, the hoist is not recommended for use in
any application where there is a possibility of adding to an
already suspended load to the point of overload. This
includes dumbwaiter installation (refer to limitations discussed in Safety Precautions on Page ii), containers that are
loaded in mid-air, etc. Also, if the hoist is used at unusual
extremes of ambient temperatures, above 150°F. or below
15°F., changes in lubricant properties may permit the hoist to
raise larger loads than under normal operating conditions
and present possibility of damage or injury.
On single phase units, it is necessary to stop the hoist before
changing direction. Therefore, when lowering a load, the
rocker in the control station must be released momentarily
before the up control is depressed to raise the load. If this
is not done, the hoist will continue to operate in the down
direction while the up control is depressed, and it will continue to lower the load until the control rocker is released. As
a result, on the single phase units, the direction must not be
reversed quickly (plug reversed).
±
TO AVOID INJURY:
Permanently ground the hoist as instructed in this manual.
GENERAL
±
L
! WARNING
Failure to properly ground the hoist presents the danger of
electric shock.
OPERATING INSTRUCTIONS
±
To avoid these low voltage problems, the hoist must be connected to an electrical power supply system that complies
with the National Electrical Code and applicable local codes.
This system must also be rated for a minimum of 20 amps
and it must have #14 AWG or larger wiring, a disconnecting
means, overcurrent protection (slow blow fuses or inverse-time
type circuit breakers) and provisions for grounding the hoist.
There are no electrical switches to stop the operation of the
hoist at the upper and lower limits of the lift. As a result, it is
necessary to release the rocker in the control station to stop
the hoist before the hook block or loose end block contacts
the bottom of the hoist frame. If the hook block or loose end
block contacts the hoist frame, the Protector™ will function to
stop the hoisting or lowering operation and protect the hoist
components from damage. However, continued, prolonged
or repeated slipping of the Protector™ will damage the
Protector™ and cause overheating of the internal hoist components.
HOIST
1. Before picking up a load, check to see that the hoist is
directly overhead.
2. WHEN APPLYING A LOAD, IT SHOULD BE DIRECTLY
UNDER HOIST OR TROLLEY. AVOID OFF CENTER
LOADING OF ANY KIND.
3. Take up a slack load chain carefully and start load easily
to avoid shock and jerking of hoist load chain. If there is
any evidence of overloading, immediately lower the load
and remove the excess load.
4. DO NOT allow the load to swing or twist while hoisting.
5. DO NOT allow the load to bear against the hook latch.
9
HOIST WITH LOW HEADROOM TROLLEY
This unit should be moved by pushing on the suspended
load or by pulling the empty hook. However, the unit can also
be moved by pulling on the control station since an internal
steel cable extends the length of the control cord and is
anchored to the hoist and to the control station.
HOIST WITH MOTOR DRIVEN TROLLEY
This unit should be moved by operating the controls marked
± (Forward) and (Reverse) in control station. Unless altered
by the erector, depressing ± (Forward) control will move the
hoist toward motor housing end. Anticipate the stopping
point and allow trolley to coast to a smooth stop. Reversing
or “plugging” to stop trolley causes overheating of motor and
swaying of load.
11. Take up a slack load chain carefully and start load easily
to avoid shock and jerking of hoist load chain. If there is
any evidence of overloading, immediately lower the load
and remove the excess load.
12. Do not allow the load to swing or twist while hoisting.
INSPECTION
PROCEDURES
±
SAFETY PROCEDURES
To maintain continuous and satisfactory operation, a regular
inspection procedure must be initiated to replace worn or
damaged parts before they become unsafe. Inspection intervals must be determined by the individual application and
are based on the type of service to which the hoist will be
subjected and the degree of exposure to wear, deterioration
or malfunction of the critical components.
For safety precautions and a list of DO’S and DO NOT’S for
safe operation of hoists, refer to page ii.
The type of service which the hoist is subjected can be classified as “NORMAL,” “HEAVY,” “SEVERE.”
1. When preparing to lift a load, be sure that the attachments to
the hook are firmly seated in hook saddle. Avoid off center
loading of any kind, especially loading on the point of hook.
2. When lifting, raise the load only enough to clear the floor
or support and check to be sure that the attachments to
the hook and load are firmly seated. Continue to lift only
after you are assured the load is free of all obstructions.
3. DO NOT load hoist beyond the rated capacity shown on
hoist identification plate or on the hoist motor housing
cover or hoist back frame cover. Overload can cause
immediate failure of some load-carrying part or create a
defect causing subsequent failure at less than rated
capacity. When in doubt, use the next larger capacity of
CM Valustar Hoist.
4. DO NOT use this or any other overhead materials handling equipment for lifting persons.
5. Stand clear of all loads and avoid moving a load over the
heads of other personnel. Warn personnel of your intention to move a load in their area.
6. DO NOT leave the load suspended in the air unattended.
7. Permit only qualified personnel to operate unit.
8. DO NOT wrap the load chain around the load and hook
onto itself as a choker chain.
Doing this will result in:
a. The loss of the swivel effect of the hook which could
mean a twisted chain and a jammed lift wheel.
b. The chain could be damaged at the hook.
9. On two part-reeved hoists, check for twists in the load
chain. A twist can occur if the lower hook block has been
capsized between the strands of chain. Reverse the capsize to remove twist.
10. DO NOT allow the load to bear against the hook latch.
The latch is to help maintain the hook in position while the
chain is slack before taking up slack chain.
L
! WARNING
Allowing the load to bear against the hook latch and/or hook
tip can result in loss of load.
TO AVOID INJURY:
Do not allow the load to bear against the hook latch and/or
hook tip. Apply load to hook bowl or saddle only.
NORMAL SERVICE: Involves operation with randomly
distributed loads within the rated load limit, or uniform
loads less than 65 percent of rated load for not more than
25 percent of the time.
HEAVY SERVICE: Involves operating the hoist within the
rated load limit which exceeds normal service.
SEVERE SERVICE: Is normal or heavy service with
abnormal operating conditions.
Two classes of inspection, FREQUENT and PERIODIC, must
be performed.
FREQUENT INSPECTIONS: These inspections are visual
examinations by the operator or other designated personnel. Records of such inspections are not required. The
frequent inspections are to be performed monthly for normal service, weekly to monthly for heavy service, and
daily to weekly for severe service, and they should
include those items listed in Table 3.
PERIODIC INSPECTIONS: These inspections are visual
inspections of external conditions by an appointed person. Records of periodic inspections are to be kept for
continuing evaluation of the condition of the hoist.
Periodic inspections are to be performed yearly for normal service, semi-annually for heavy service and quarterly for severe service, and they are to include those items
listed in Table 4.
CAUTION: Any deficiencies are to be corrected
before the hoist is returned to service. Also, the
external conditions may show the need for disassembly to permit a more detailed inspection, which,
in turn, may require the use of non-destructive type
testing.
Preventive Maintenance
In addition to the above inspection procedure, a preventive
maintenance program should be established to prolong the
useful life of the hoist and maintain its reliability and continued
safe use. The program should include periodic and frequent
inspections with particular attention being paid to the lubrication of the various components using the recommended lubricants (see page 12).
10
Table 3
Minimum Frequent Inspections
Normal
Type of Service
Heavy
Item
Severe
a) Brake for evidence of slippage.
b) Control functions for proper operation.
Yearly
Weekly
to
Yearly
Daily
to
Weekly
c) Hooks for damage, cracks, twists, excessive throat opening, latch
engagement and latch operation – see page 11.
d) Load chain for adequate lubrication, as well as for signs of wear,
damaged links or foreign matter – see page 11.
e) Load chain for proper reeving and twists.
Table 4
Minimum Periodic Inspections
Normal
Type of Service
Heavy
Item
Severe
a) All items listed in Table 3 for frequent inspections.
b) External evidence of loose screws, bolts or nuts.
Yearly
Every
Six
Months
Every
Three
Months
c) External external evidence of worn, corroded, cracked or distorted
hook block, suspension bolts, gears, bearings, loose end chain, stop
block, loose end block and pins, and dead end block and pin
(double reeved units).
d) External evidence of damage to hook retaining nut or collar and pin.
Also check the upper suspension adapter making sure it is fully seated in the hoist frame and retighten the screws to the recommended
seating torque (see page 4). If a condition of loose screws persists,
replace the self-locking nuts in the frame.
e) External evidence of damage or excessive wear of the liftwheel and
hook block sheave (double reeved units) chain pockets. Widening
and deepening of the pockets may cause the chain to lift-up in the
pocket and result in binding between liftwheel and chain guides or
between the sheave and hook block (double reeved units).
Also, check the chain guides for wear or burring where the chain
enters the hoist.
Severely worn or damaged parts should be replaced.
f) External evidence of excessive wear or brake parts and brake
adjustment – see page 12.
g) External evidence of pitting or any deterioration of contactor contacts.
h) Inspect the electrical cords and cables for damaged insulation.
i) Inspect trolley trackwheels for external wear on tread and flange,
and for wear on internal bearings surfaces as evidenced by a looseness on the stud.
11
M
EA
O SU
PE R
NI E
NG
LATCH TYPE HOOK
(Upper and Lower)
TO MEASURE OPENING,
DEPRESS LATCH
AGAINST HOOK BODY
AS SHOWN
Models
WB, WF
WE, WH, WJ & WL
WR
Replace Hook When Opening is
Greater Than
1-3/16
1-5/16
1-1/2
Figure 9. Hook Inspection
Hook Inspection
Hooks damaged from chemicals, deformations or cracks, or
that have more than a 10° twist from the hook’s unbent plane
or excessive opening or seat wear must be replaced. Also,
hooks that are opened and allow the latch to not engage the
tip, must be replaced. Any hook that is twisted or has excessive throat opening indicates abuse or overloading of the
unit. Inspect other load sustaining parts for damage.
tion for nicks, gouges, twisted links, stretching and excessive
wear. In particular, observe the bearing surface between
links, and if any of these conditions exist, the load chain must
be replaced. Chain should be gaged throughout its entire
length and replaced if beyond serviceable limits.
To determine if load chain should be continued in service,
check gage lengths as indicated in Figure 10. Chain worn
beyond length indicated, nicked, gouged or twisted should
be replaced before returning hoist to service. Chain should
be clean, free of twists and pulled taut before measuring. In
cases where the wear is localized and not beyond serviceable limits, it is sometimes possible to reverse the load chain,
end for end, and allow a new section to take the wear.
Removal and installation of the load chain is covered in subsequent paragraphs.
To aid in gaging load chain wear. A chain gage can be
obtained from CM. This can be obtained by ordering chain
gage Part No. 3191.
CAUTION: Before installing new load chain, the unit
must be disassembled to allow inspection for damage or wear and replacement, if required, of mating
parts (liftwheel, chain guides, motor and gear housings).
On latch type hooks, check to make sure that the latch is not
damaged or bent and that it operates properly with sufficient
spring pressure to keep the latch tightly against the tip of the
hook and allow the latch to spring back to the tip when
released. If the latch does not operate properly, it should be
replaced. See Figure 9 to determine when the hook must be
replaced.
Figure 10. Gaging Load Chain Wear
Protector™
The Protector™ should operate for the normal life of the hoist
without service. The device has been lubricated and calibrated at the factory for a specific model of hoist and is not
adjustable or interchangeable with other models. For proper
overload protection be sure before installing a Protector™
that it is correct for the unit. The spring washer of the
Protector™ has been color coded at the factory as follows:
Models
WB, WE
WE, WH
WJ
WL, WR
Protector™ Color Code
White
Orange
Red
Green
L
! WARNING
Removing the snap ring on the Protector™ assembly will
allow the parts to spring apart.
TO AVOID INJURY:
Do not attempt to disassemble the Protector™.
LOAD CHAIN
Clean and Inspection
First clean the load chain with a non-acid or non-caustic type
solvent, then slack the chain and make a link-by-link inspec-
Models
WE, WB,
WF & WH
WJ, WL,
and WR
Dia. of
Chain Stock
0.250"
0.312"
No. of Links Max. Gage Length
to Gage
Allowable
Used Chain
19
14-13/16"
21
18-7/8"
When installing new load chain or mating parts, refer to
Lubrication on page 12.
IMPORTANT: Do not use replaced chain for other
purposes such as lifting or pulling. Load chain may
break suddenly without visual deformation. For this
reason, cut worn chain into short lengths to prevent
use after disposal.
L
! WARNING
Using other than CM supplied load chain may cause the chain
to jam in the hoist and/or allow the chain to break and the load
to drop.
TO AVOID INJURY:
Due to size requirements and physical properties, use only CM
HOISTALOY® load chain in the CM Valustar Hoists.
12
MAINTENANCE
L
! WARNING
conditions, it may be necessary to clean the chain at least once a day
and lubricate it several times between cleanings.
When lubricating the chain, apply sufficient lubricant to obtain natural
run-off and full coverage.
L
! WARNING
The lubricants used in and recommended for the Valustar
Hoist may contain hazardous materials that mandate specific
handling and disposal procedures.
TO AVOID CONTACT AND CONTAMINATION:
Handle and dispose of lubricants only as directed in applicable material safety data sheets and in accordance with applicable local, state and federal regulations.
Used motor oils contain known carcinogenic materials.
TO AVOID HEALTH PROBLEMS:
Never use used motor oils as a chain lubricant. Only use
Lubriplate Bar and Chain Oil 10-R as a lubricant for the load
chain.
HOIST LUBRICATION
Low Headroom Trolley
NOTE: To assure extra long life and top performance, be sure to lubricate the various parts of the
Valustar Hoist using the lubricants specified below.
If desired, these lubricants may be purchased from
CM. Refer to page 22 for information on ordering the
lubricants.
CM trackwheel bearings are pre-lubricated and require no lubrication.
Gears
The Protector™ should operate for the normal life of the hoist
without service. The device has been lubricated and calibrated at the factory for a specific model of hoist and is not
adjustable or interchangeable.
CAUTION: The Protector™ is to be used with
“Century Lubricants HB-11, #3” grease. Use of any
other grease will damage Protector™ parts or cause
improper operation.
The gears and Protector™ are factory greased and should
not need to be renewed unless the gears have been
removed from the housing and degreased.
CAUTION: Never degrease or attempt to disassemble the Protector™. Degreasing may damage parts
or cause erratic, inconsistent operation. If the
Protector™ has been degreased, it must be replaced
by a factory calibrated device.
If the gears are removed from the housing, wipe the excess
grease off the outside Protector™ surfaces with a soft cloth
and degrease the remaining gears and housings. Upon
reassembly, add 7 oz. of above grease to gears and housing. Also, coat the spline on the end of the drive shaft with a
molydisulphide lubricant such as “Super Herculon.”
Bearings
All bearings and bushings except the lower hook thrust bearing are prelubricated and require no lubrication. Lubricate
the lower hook thrust bearing at least once a month, using a
heavy cup grease.
Chain Guides, Liftwheel & Lower Sheave Wheel
When the hoist is disassembled for inspection and/or repair,
the chain guides, lower sheave wheel (on double chain units)
and liftwheel must be lubricated with Lubriplate, Bar and
Chain Oil 10-R (Fiske Bros. Refining Co.) prior to reassembly.
Apply sufficient lubricant to obtain run-off and full coverage.
Load Chain
A small amount of lubricant will greatly increase the life of load
chain. Do not allow the chain to run dry. Keep it clean and lubricate at regular intervals with Lubriplate, Bar and Chain Oil 10-R
(Fiske Bros. Refining Co.) or equal lubricant. Normally, weekly
lubrication and cleaning is satisfactory, but under hot and dirty
ELECTRIC BRAKE ADJUSTMENT
The correct air gap between armature and field, when brake is not
energized, is 0.035 inch and need not be adjusted until the gap
reaches 0.075 inches. To adjust the brake, proceed as follows:
1. Disconnect hoist from power supply.
2. Remove back frame cover.
3. Before adjusting the gap:
a) back off the stud nuts and examine friction linings and friction
surfaces for excessive wear, scoring or warpage.
b) check shading coils to be sure they are in place and not broken. A missing or broken shading coil will cause noisy brake
operation.
These symptoms indicate the need for parts replacement.
4. Turn adjusting nuts clockwise gaging the air gap at both ends.
5. Replace cover, reconnect the power and check operation.
EXTERIOR FINISH
The exterior surfaces of the hoist and trolleys have a durable, scratch
resistant baked powder coating. Normally, the exterior surfaces can
be cleaned by wiping with a cloth. However, if the finish is damaged,
compatible touch-up paint can be purchased from CM. Refer to
page 22 for information on ordering the paint.
RECOMMENDED SPARE PARTS
To insure continued service of the Valustar Hoist, the following is a list
of parts that are recommended to be kept on hand at all times to
replace parts that have worn or failed:
Qty. for each
Part Name
Hoist in Service
Brake Friction Disc
Models WB & WE
1
All Other Models
2
624-199
Brake Coil
1
624-213
Capacitor
(115-1-60 Units Only)
1
624-215
Cut-Out Switch
(115-1-60 Units Only)
1
624-216
Contactor
1
624-218
Transformer
(Three-phase Units Only)
1
624-306
Control Station Parts Kit
1
624-307
Control Station Switch Kit
1
624-778
Solid State Reverse Switch
1
Refer to Page 21 for ordering information and parts list for the part
numbers.
Key No.
624-197
13
TROUBLE SHOOTING
––– Remedy–––
––– Probable Cause –––
1. Hook does not respond to control station.
A. No voltage at hoist – main line or branch circuit switch open; branch line fuse
blown or circuit breaker tripped.
B. Phase failure (single-phasing, three-phase unit only) – open circuit, grounded or
faulty connection in one line of supply system, hoist wiring, reversing contactor,
motor leads or windings.
C. Open control circuit – open or shorted winding in transformer or reversing
contactor coil; loose connection or broken wire in circuit; mechanical binding in
contactor; control station contacts not closing or opening
D. Wrong voltage or frequency.
E. Low voltage.
F. Brake not releasing – open or shorted coil winding; armature binding.
G. Excessive load.
A. Close switch, replace fuse or reset breaker.
B. Correct power supply system. Check for electrical continuity and repair or replace
defective part.
C. Check electrical continuity and repair or replace defective part.
D. Use the voltage and frequency indicated on hoist identification label.
E. Correct low voltage condition as described on page 7.
F. Check electrical continuity and connections. Check that correct coil has been
installed. The coil for three phase dual voltage unit operates at 230 volts when the
hoist is connected for either 230 volt or 460 volt operation. Check brake adjustment (page 12).
G. Reduce load to the capacity limit of hoist as indicated on the hoist identification
label.
2. Hook moves in wrong direction.
A. Wiring connections reversed at the control station.
A. Use wiring diagram and check wiring connections.
B. Failure of the motor cut-out switch to effect dynamic braking at time of reversal
(single-phase units only).
C. Phase reversal (three-phase units only).
B. Check connections to switch. Replace damaged switch or faulty capacitor.
C. Refer to installation instructions page 7.
3. Hook lowers but will not raise.
A. Excessive load.
B. Open hoisting circuit – open or shorted winding in reversing contactor coil; loose
connection or broken wire in circuit; control station contacts are not making.
C. Motor cut-out device not operating. (single-phase units only).
D. Phase failure (three-phase units only).
A. See item 1G.
B. Check electrical continuity and repair or replace defective part.
C. Check the switch connections and actuating bar and contact for sticking or damage. Check centrifugal mechanism for loose or damaged components. Replace
defective parts.
D. See item 1B.
4. Hook raises but will not lower.
A. Open lowering circuit – open or shorted winding in reversing contactor coil; loose
connections or broken wire in circuit; control station contacts not making.
B. Motor cut-out switch not operating (single-phase units only).
A. Check electrical continuity and repair or replace defective part.
B. See item 3C.
5. Hook lowers when hoisting control is operated.
A. Phase failure (three-phase units only).
A. See item 1B.
6. Hook does not stop promptly.
A. Brake slipping.
B. Excessive load.
A. Check brake adjustment as described on page 12.
B. See item 1G.
7. Hoist operates sluggishly.
A.
B.
C.
D.
Excessive load.
Low voltage.
Phase failure or unbalanced current in phases (three-phase units only).
Brake dragging.
A.
B.
C.
D.
See item 1G.
Correct low voltage condition as described on page 7.
See item 1B.
Check brake adjustment as described on page 12.
8. Motor overheats.
A. Excessive load.
B. Low voltage.
C Extreme external heat.
D. Frequent starting or reversing.
E. Phase failure or unbalanced current in the phases (three-phase units only).
F. Brake dragging.
G. Motor cut-out device not opening start winding circuit (single-phase units only).
A. See item 1G.
B. Correct low voltage condition as described on page 7.
C. Above an ambient temperature of 104°F (40°C), the frequency of hoist operation
must be limited to avoid overheating the motor. Special provisions should be made
to ventilate the space or shield the hoist from radiant heat.
D Avoid excessive inching, jogging or reversing. This type of operation drastically
shortens the motor and contactor life and causes excessive brake wear.
E. See item 1B.
F. Check brake adjustment as described on page 12.
G. See Item 3C.
9. Hook fails to stop either or both.
A. Shaft not rotating.
A. Check for damaged gears.
14
element and impose normal voltage) or D.C. resistance substantially below normal. The current method is recommended
for coils with very low D.C. resistance.
ELECTRICAL DATA
To Detect Open and Short Circuits in
Electrical Components
Open circuits in the coils of electrical components may be
detected by isolating the coil and checking for continuity with
an ohmmeter or with the unit in series with a light or bell circuit.
Motor current draw in the stator should be measured with the
rotor in place and running. Brake, relay and contactor coil
current should be measured with the core iron in operating
position.
Shorted turns are indicated by a current draw substantially
above normal (connect ammeter in series with suspected
Table 5
Electrical Data for Hoist Components
CONTACTOR
Models
Voltage
TRANSFORMER
Voltage
230/480
TO 115
Leads
Secondary:
Blue-tan to Blue
Primary:
Red-black
to Red-blue
Primary:
White-red to
White-green
WB, WE,
WF & WH
WJ, WL,
and WR
D.C. Resistance
(Ohms)*
19.5
.
87.5
Coil
(Volts)
Normal
D.C. Resistance
Current (Amps)
(Ohms)*
120
.04
297.5
120
.04
297.5
BRAKE COIL
Rated
Voltage
115
230**
99.0
Nominal Current
D.C. Resistance
(Amps) at Rated Voltage
(Ohms)*
0.5
6.2
0.25
24.7
MOTORS
Models
WB, WE
Voltage
Phase
& Hertz
115-1-60
H.P.
1/4
Full Load
Current
(Amps)
4.6
WB, WE
230/460
3-60
1/4
1.4/.70
WF, WH
115-1-60
1/2
7.2
WF, WH
230/460
3-60
1/2
1.8/.90
WL, WR
115-1-60
1
9.8
WJ, WL, WR
230/460
3-60
1
3/1.5
*Resistance values listed are nominal and they may vary slightly from component to component.
**On dual-voltage units connected for 460 volts, brake coils operate on 230 volts.
Leads
5 TO 8 (START)
T1 to T2
T3 to T4
1 to 4
2 to 5
3 to 6
7 to 8
7 to 9
8 to 9
5 to 8 (START)
T1 to T2
T3 to T4
1 to 4
2 to 5
3 to 6
7 to 8
7 to 9
8 to 9
5 to 8 (START)
T1 to T2
T3 to T4
1 to 4
2 to 5
3 to 6
7 to 8
7 to 9
8 to 9
*D.C.
Resistance
(Ohms)
4.9
4.3
4.3
14.8
14.8
14.8
29.5
29.5
29.5
3.7
3.8
3.8
7.8
7.8
7.8
15.6
15.6
15.6
1.3
1.1
1.1
4.7
4.7
4.7
9.4
9.4
9.4
15
SINGLE PHASE-TYPE ‘T’ CONTACTOR
110-120 VOLT
SINGLE PHASE-TYPE ‘T’ CONTACTOR
110-120 VOLT
THREE PHASE
230/460-3-60
220/380-415-3-50
MODELS WB, WE, WF &
WH
THREE PHASE
230/460-3-60
220/380-415-3-50
MODELS WJ, WL & WR
Figure 11. Typical Wiring Diagrams. Wiring Diagrams shown are representative. Consult diagram in Hoist or furnished with unit.
16
ASSEMBLY
HOOK OR LUG SUSPENSION
Models WE, WH, and WR
Assemble the dead end bolt and block through the suspension adapter, as shown in Figure 12.
To install the replacement mechanism, a press-on tool as shown
in Figure 13 will be required. The press-on tool is not included in
the kit, however, it may be ordered from CM – order centrifugal
mechanism press-on tool part number 28598.
When installing the replacement centrifugal mechanism, the
spacer is placed between the rotor shaft shoulder and the centrifugal mechanism as shown in Figure 13. Using a slow-acting
press, apply pressure to the press-on tool and press the mechanism onto the shaft until it sets against the spacer. To prevent
damaging the mechanism and/or spacer, the force applied to
the press-on tool press the mechanism onto the shaft should
not exceed 3000 pounds.
FASTENERS
Models WE, WB, WF and WH, tighten motor housing cover
screws (624-106) to where they have a minimum breakaway
torque of 48 pound inch.
Models WJ, WL and WR tighten motor thru bolts (624-140) to
where they have a minimum breakaway torque of 50 pound
inch.
The liftwheel gear nut (624-139) should be tightened to a seating torque of 85 pound feet.
LOWER HOOK BLOCK PIN
Figure 12. Hook Suspension
CENTRIFUGAL MECHANISM
Centrifugal mechanism (624-212) is furnished in kit form
which contains the centrifugal mechanism, spacers and an
Instruction Sheet. The Instruction Sheet provides complete
details on the installation of replacement mechanism.
Figure 13. Centrifugal Mechanism Assembly
When removing or installing the lower hook chain block pin
(624-764), care must be taken so as to prevent damaging the
pin and/or hook block. These pins are tapered groove pins and,
as a result, they can only be removed in one direction. To
remove the pin, a V-Block, drift and hammer (or slow acting
press) are required. The drift should be the same diameter as
the pin (5/16" diameter for Models WB, WE, and WF and 3/8"
diameter for Models WJ and WL) and it should be placed on
17
the small end of the pin. The small end of the pin is the end
opposite the end on which the three grooves are visible.
Place the hook block in the V-Block and drive the pin out
using the drift and a hammer or slow acting press.
L
! WARNING
Use of improper lower hook chain block pin as well as improper
installation of this pin can cause the pin to break and allow the
load to fall.
TO AVOID iNJURY AND PROPERTY DAMAGE:
Use only CM supplied, special high strength lower hook chain
block pin to attach the chain to the lower hook block and
install the pin as directed above.
To re-install the pin, the parts must be arranged the same as
they were when the pin was removed. To do this, use the
small end of the pin as a gage. First check the holes in the
hook block body and determine which hole is the largest.
Place the hook block body in the V-Block with the larger hole
on top. Next, check each end of the hole in the lower hook
chain block (624-775) and determine which end is the
largest. Place the chain in the slot of the chain and insert the
chain block, with the large hole on top, into the hook block
body. Align the holes in the hook block body with the hole in
the chain block and insert the small end of the pin in the
hole. Push the pin in by hand until it stops and then use a
hammer or slow acting press to drive the pin into position so
that the end of the pin is flush with the outside surface of the
hook block body.
REMOVAL AND INSTALLATION OF
LOAD CHAIN
! WARNING
L
Improper installation (reeving) of the load chain can result in a
dropped load.
TO AVOID INJURY/DAMAGE:
Verify use of proper size and type of hoist load chain for
specific hoist.
1. Disconnect hoist from power supply.
2. Detach loose end chain from hoist frame. Remove loose
end block and stop block from the old load chain.
3. Using the following procedures (cutting chains) cut a portion out of the second to last link (flat link) on the loose
side of the old chain to form a coupling link. The portion
removed should be centered on the weld and be 3/8"
long. Remove any burrs from the cut edges of the coupling link. Discard the last link.
4. Connect the new chain to the old chain using the coupling
link. The coupling link should be a flat link and the first link
of the new chain should be an upstanding link. Be sure the
welds on the upstanding links are away from the liftwheel.
5. Re-energize power supply and operate hoist in the down
direction until approximately two and one-half (2-1/2') feet
of the new chain is hanging free on the loose end side.
Make sure that the last link of the new chain is an upstanding link. Slide the stop block onto the new chain and attach
the loose end block to the chain using the load chain pin.
Next, attach the loose-end chain to the hoist frame using
the loose-end screw washer and plain washer.
Note: If hoist is equipped with a chain container, do
not attach the loose end chain to the hoist frame.
6. On single reeved units, remove the lower hook block from
the old chain and remove the coupling link. Reassemble
the hook block to the last link of the new chain. (See
above-lower hook block pin.)
On double reeved units, pull the new chain through the
hook block using the old chain and coupling link. Be sure
there are no twists in the chain and the first link of the new
chain is a flat link.
NOTE: Upstanding links in the hook block will
have weld towards the sheave.
Remove the coupling link and remove the old chain from
the dead end block at the hoist. Run the new chain up to
the dead end block making sure there is no twist in the
chain between the hook block and dead end block.
Attach the last link (flat link) of the new chain to the dead
end block.
If the hoist is completely disassembled when the new chin is
to be installed, the new chain should be placed over the liftwheel (with weld on upstanding links away from liftwheel).
Leave 2-1/2' of chain hanging free on the loose end side.
Refer to steps 5 and 6 above to complete the installation.
Note: On the double chain units, it will be necessary
to use a length of soft wire to pull the new chain
through the hook block in lieu of using the coupling
link and old chain as indicated.
Use only CM Star () Grade Load Chain and CM replacement parts. Use of
other chain and parts may be dangerous and voids factory warranty.
L
! WARNING
Use of commercial or other manufacturers’ chain and parts to
repair CM Hoists may cause load loss.
TO AVOID INJURY:
Use only CM supplied replacement load chain and parts. Chain
and parts may look alike, but CM chain and parts are made of
specific material or processed to achieve specific properties.
If the starter chain method is not used, the chain can be
installed by partially disassembling the hoist. Remove the
loose-end chain, loose-end block and stop block from the
chain. Then, energize the hoist to carefully run the old chain
out of the hoist. Disconnect the hoist from the power supply
and remove the electric brake assembly. Rotate the brake
hub by hand, at the same time feeding the new chain into
and through liftwheel area with the hoist upside down or using
a soft wire to pull the chain up onto the liftwheel. Be sure that
the weld on the upstanding link is away from the liftwheel.
Refer to steps 5 and 6 above to complete the installation.
NOTE: On the double reeved units, it will be necessary to use a length of soft wire to pull the new
chain through the hook block in lieu of using the
coupling link and old chain as indicated.
18
CUTTING CHAINS
CM Hoistaloy load chain is hardened and it is difficult to cut.
The following methods are recommended when cutting a
length of new chain from stock or cutting off worn chain.
®
Protector™ permits lifting a load in excess of 200% of
rated load, it should be replaced.
*If the protector prevents lifting a load of 125% of rated
capacity, reduce load to rated capacity.
NOTE: For additional information on inspection and
testing, refer to Code B30.16 “Overhead Hoists”
obtainable from ASME Order Department, 22 Law
Drive, Box 2300, Fairfield, NJ 07007-2300, U.S.A.
Grinder
Nicks
REPLACEMENT PARTS
ORDERING INSTRUCTIONS
Figure 14. Cutting Chain by nicking
1. Use a grinder and nick the link on both sides (Figure 14),
then secure the link in a vise and break off with a hammer.
2. Use a 7" minimum diameter by 1/8" thick abrasive wheel
(or type recommended by wheel supplier) that will clear
adjacent links.
The following information must accompany all correspondence or orders for replacement parts:
1. Hoist Model Number from identification label.
2. Serial number of the hoist stamped below identification
plate.
3. Voltage, Phase, Hertz from identification label.
4. Length of lift.
5. Key number of part from parts list.
6. Number of parts required.
7. Part name from parts list.
8. Part number from the parts lists.
If trolley replacement parts are ordered, also include the type
and capacity of the trolley.
Figure 15. Cutting Chain with a bolt cutter
3. Use a bolt cutter (Figure 15) similar to the H.K. Porter
No. 0590MTC with special cutter jaws for cutting hardened chain (1" long cutting edge).
L
!
WARNING
Cutting chain can produce flying particles.
TO AVOID INJURY:
Wear eye protection. Provide a shield over chain to prevent
flying particles.
TESTING
Before using, all altered, repaired or used hoists that have
not been operated for the previous 12 months shall be tested
by the user for proper operation.
1. Test the unit without a load.
2. Test the unit with a light load of 50 pounds times the number of load supporting parts of load chain. Check to see
that the hoist operates properly and that the brake holds
the load when the control is released.
3. Test with a load of 125%* of rated capacity. Hoists in
which load sustaining parts have been replaced should
be tested with 125%* of rated capacity by or under the
direction of an appointed person and a written report prepared for record purposes.
4. After test 3, check that the Protector functions. If the
NOTE: When ordering replacement parts, it is recommended that consideration be given to the need for
also ordering such items as gaskets, fasteners, insulators, etc. These items may be damaged or lost during
disassembly or just unfit for future use because of
deterioration from age or service.
L
! WARNING
Using “commercial” or other manufacturer’s parts to repair
the CM Valustar Hoist may cause load loss.
TO AVOID INJURY:
Use only CM supplied replacement parts. Parts may look alike,
but CM parts are made of specific materials or processed to
achieve specific properties.
19
PARTS LIST
NUMBER REQUIRED
KEY
NO.
PART NAME
624-100 Motor Housing
PART NUMBERS
Models WB, Models WJ, Model
WE, WF, WH WL, WR
WB
1
Model
WE
1
Model
WF
Model
WH
Model Model
WJ
WL
27028
Model
WR
24008
28669
35620
(Includes Item 624-102)
(Includes Items 624-102, 624-120, 624-129)
624-101 Gear Housing
1
1
Intermediate Gear and Pinion
624-102 Bearing - Inboard
1
1
88440
Order 83670 (Bearing)
and 24350 (Shaft Adapter)
624-103 Chain Guide
2
2
27008
35018
624-104 Liftwheel
1
1
27360
35421
624-105 Suspension Adapter Nut
Motor Housing Cover Screw
624-106
and Lockwasher
624-107 Liftwheel Gear Retainer Ring
Motor Shaft Bearing, Inboard
624-108
Retainer Ring
Gear Housing Attaching Screw
624-109
and Lockwasher
Loose End Screw, Washer
624-110
and Lockwasher
624-111 Motor Shaft Bearing - Outboard
2
2
927755
935791
2
2
C302
C303
1
---
27767
---
2
2
27790
35764
4
4
Order 28830 Screw
and 940802 Lockwasher
Order 982682 Screw
and 940830 Lockwasher
1
1
C304
C305
1
---
82009
---
624-112 Motor Shaft Bearing - Inboard
1
1
82003
82004
624-113 Stator Pin
Control Cable Screw, Washer
624-114
and Lockwasher
Back Frame Assembly
624-115
(Includes Brake Studs)
1
---
983541
---
1
1
C306
C306
1
1
24620
(Includes 624-116 thru 624-118, 624-127, 624-128)
24622
624-116 Drive Shaft and Pinion Bearing
Intermediate Gear and Pinion
624-117
Bearing - Outboard
Bearing Retainer Screw
624-118
and Washers
Back Frame Attaching Screw
624-119
and Lockwasher
624-120 Liftwheel Bearing - Gear End
1
1
82009
83691
1
1
82009
88437
1
2
C307
C308
3
4
1
1
Order 982699 Screw
and 940802 Lockwasher
88429
Order 982682 Screw
and 940830 Lockwasher
82002
624-121 Motor Housing Cover
1
1
24504
24759
624-122 Back Frame Cover
Back Frame Cover Attaching Screw
624-123
and Lockwasher
624-125 Hoist I.D. Label 115-1-60, 230/460
1
1
24757
24758
2
2
C309
C310
1
1
624-126 Capacity/Warning Label
1
1
624-127 Hole Plug Set
4
1
982454
624-128 Back Frame Expansion Plug
1
---
940837
---
624-129 Gear Housing Plug
Drive Shaft and Pinion Assembly
---
1
---
935767
1
1
Order 624-116, 624-131,
624-132 and 624-133
624-131 Drive Shaft and Pinion Assembly
1
1
624-132 Brake Hub
1
1
624-133 Brake Hub Retainer Ring
1
1
24641
24642
(8T. Pinion, 5-15/64” Long) (8T Pinion, 5 43/64” Long)
27851
27852
(8T. 21/32” Long)
(8T. 1-1/8” Long)
27766
624-134 Liftwheel Gear
1
1
27009 (53T.)
35009 (79T.)
624-135 Intermediate Pinion
1
1
24351 (8T.)
35351 (10T.)
624-136 Intermediate Gear Retainer Ring
1
1
27765
624-137 Protector
1
1
624-138 Liftwheel Bearing - Motor End
1
1
88429
83669
624-139 Liftwheel Gear Nut and Lockwasher
---
1
---
C312
(Includes Shaft Adapter for WJ, WL, WR)
(Includes Items 624-131 thru 624-133 for
624-130 Models WB, WE, WF, WH, WJ, WL and WR.
Also Includes Item 624-116 with Models
WJ, WL, WR
Contact Factory
24764
24765
Contact Factory
24765
28694
24766
24765
24766
24768
C311
24639
24638
24638
35357
(18T.)
35356
(12T.)
24019
(13T.)
35766
35356
(12T.)
24019
(13T.)
---
35763
28695
36668
36670
36670
20
PARTS LIST, continued
Key
No.
624-140
Part Name
Motor Attaching Screw and
Lockwasher
NUMBER REQUIRED
Models WB, Models WJ, Model
WE, WF, WH WLWR
WB
PART NUMBERS
Model Model Model
WF
WH
WJ
Model
WE
Model
WL
Model
WR
For all Units, order (4) 87377
Motor Thru Bolts and (4) 982226
Lockwashers
82639
---
4
----
624-142 Loose End Nut
1
1
82638
624-143 Contactor/Capacitor Bracket with
Attaching Screws
624-145 Capacitor Clamp with Attaching
Screws and LockWasher
---
1
---
1
Order (1) Bracket 24200 and (1) Screw
982688
---
624-146 Loose End Link
1
1
35367
624-147 Contact Block
---
1
---
---
---
624-149 Brake Disc Retainer Ring
---
1
---
---
24801
---
624-151 Lower Hook with Latch
(Includes Item 624-152)
624-152 Latch Kit
1
1
28686
35611
35611
35612
1
1
45661
45662
45662
45663
624-156 Load Chain (Specify Length)
1
1
624-157 Lower Hook Assembly-Complete
(Items 624-151 and 624-158)
624-158 Lower Hook Collar (or Nut) Pin
and Thrust Bearing
1
1
---
28665
---
28665
---
---
35645
1
1
---
C325
---
C325
---
---
C326
624-159 Lower Sheave
1
1
---
27017
---
27017
---
---
35010
624-160 Lower Sheave Bearing
2
2
---
88429
---
88429
---
---
83674
624-161 Hook Block (*Must order in pairs
with 624-162)
624-162 Chain Stop Block
2
2
---
27048
---
27048
---
---
35034
35367
28687
28686
28687
45662
45661
45662
85889 (Specify Length Required)
2
Order Bracket 35701 and (2)
Screws 983643
Order (1) 35268 Clamp, (1)
982210 Washer, (1) 983544
Lockwasher and (1) 987354 Screw
36764
85979 (Specify Length Required)
23465903C
23465603C
624-163 Chain Stop Screw
2
982517
624-164 Chain Stop Lockwasher
2
10095701
624-165 Chain Stop Nut
2
982514
624-166 Stop Block
1
1
624-167 Alignment Pin
4
2
624-170 Suspension Adapter
1
1
27703
27013
27703
27013
35740
35740
35741
624-171 Upper Hook with Latch
(Includes Item 624-152)
1
1
28689
28697
28689
28697
35617
35617
35616
624-172 Upper Hook Collar (or Nut) and Pin
1
1
C329
C330
C329
C330
C331
C331
C332
624-173 Suspension Adapter Screw
2
2
624-174 Rigid Hook Suspension-Complete
1
1
2788
2789
2788
2789
3651
3651
3658
624-175 Dead End Bolt
1
1
---
89508
---
89508
---
---
35957
624-176 Dead End Block, Pin, Washer
and Cotter Pin
624-177 Suspension Lug
1
1
---
C334
---
C334
---
---
C335
1
1
27450
27452
27450
27452
35456
35456
35457
2778
2779
2778
2779
3677
3677
3668
624-178 Lug Suspension - Complete
624-179 Suspension Adapter Anchor
---
2
624-180 Back Frame Dowel
---
624-190 Brake Plate
1
624-191 Brake Friction Plate
24785
24786
82354
82354
987554
36849
---
35066
2
---
35768
1
24741
24740
2
2
24603
24602
624-192 Brake Field
1
1
24606
24608
624-193 Brake Armature
1
1
24607
24609
624-194 Brake Spring
2
2
24731
24732
624-195 Brake Nut
2
2
982442
982443
1
1
24738
24738
1 (Models WB, WE)
27817
24735
624-196 Brake Coil Retainer Strap
624-197 Brake Disc
2 (Models WF, WH, WJ, WL,WR)
624-198 Brake Friction Plate-Double
(Not Required for Models WB, WE)
624-199 Brake Coil
1
1
24600
24601
1
1
See Parts List on Page 22
See Parts List on Page 22
21
PARTS LIST, continued
Key
No.
Part Name
624-200 Gear Housing Gasket
624-210 Rotor Assembly
(Items 624-108 and 624-112 included)
(For 115-1-60 Units, Item 624-212 Included)
624-211 Stator
(Also order 624-113 for Models WB, WE, WF, WH)
624-212 Centrifugal Mechanism and Spacer
624-213 Capacitor
115-1-60
624-214 Capacitor Mounting Clamp and Screw
624-215 Cut-out Switch with Attaching Screws
115-1-60
NUMBER REQUIRED
PART NUMBERS
Models WB, Models
Model Model Model Model Model Model Model
WE, WF, WH WJ, WL, WR WB
WE
WF
WH
WJ
WL
WR
1
1
1
1
1
1
---
See Parts List on Page 22
See Parts List on Page 22
C349
---
27716
35278 Run Capacitor
35279 Start Capacitor
See Key No. 624-145
1
1
1
C336
---
Order (1) Cut-Out Switch 24675 & (2)
Screws 987523
1
1
1
624-218 Transformer with Attaching Screws
1
1
624-219 Wire Nuts (Specify Number Required)
---
---
624-221 Power Cord
115-1-60
230/460-3-60
624-230 Control Station and Cable
10 ft. Lift Units
15 ft. Lift Units
20 ft. Lift Units
All Other Lifts
624-231 Control Cable
10 ft. Lift Units
15 ft. Lift Units
20 ft. Lift Units
All Other Lifts
624-232 Control Station
35707
See Parts List on Page 22
1
624-216 Contactor with Attaching Screw
624-220 Jumper Set
27747
See Parts Lists on Page 22
1
1
1
1
1
1
1
1
1
Order (1) Contactor 28553, (2) Screws
957854 and (2) Lockwashers 957855
C343 (230/460 Units Only)
982473 (Small) or 982477 (Large)
--For 115-1-60 Units, Order (1)
Contactor 35182, (2) Screws
957854 and (2) Lockwasher
957855.
For 230/460-3-60 Units, Order
(1) Contactor 24729, (2)
Screws 957854 and (2)
Lockwashers 957855
Order (1) Transformer 24900
& (2) screws 982683
982473 (Small) or 982477 (Large)
For 115-1-60 Units, Order (1) 51847,
(1)51858, (1)51861 and Jumpers
For 115-1-60 Units, Order (1 Each) 51847,
(3)27599 (1)24300, (1)24301, (1)24302
24111, 24112 and 24113 Jumpers.
& (1)24303.
For 230/460-3-60 Units, Order (1 Each) 24111,
For 230/460-3-60 Units, Order (1 each)
24112, and 24113.
20331
24106
24107
24119
24120
24100
24101
24102
Contact CM
24100
24101
24102
Contact CM
24121
24122
24123
Contact CM
See Figure 16, Page 22
1
1
24121
24122
24123
Contact CM
See Figure 16, Page 22
624-233 Warning Tag
1
1
81704
81704
624-234 Product Label
1
1
24707
24707
624-240 Rotor Wave Washer
1
---
27292
---
624-241 Rotor Bearing Spacer
1
---
27291
---
624-252 Warning Label (Electrical)
2
2
24842
24842
624-760 Lower Hook and Block Assembly
1
1
28683
---
28683
---
35651
35651
---
624-763 Lower Hook Body
1
1
45401B
---
45401B
---
35370
35370
---
624-764 Lower Hook Chain Block Pin
1
1
45943
---
45943
---
35790
35790
---
1
28686
---
28686
---
35611
35611
---
1
88485
---
88485
---
88485
88485
---
---
983772
---
983772
983772
---
624-771 Lower Hook with Latch
624-772 Lower Hook Thrust Bearing
1
1
624-774 Lower Hook Nut Pin
1
1
983772
624-775 Lower Hook Chain Block
1
1
1
1
28007
---
28007
---
35026
35026
---
624-776 Lower Hook Nut
982526
---
982526
---
982526
982526
---
624-777 Lower Hook Block Washer
1
1
945921
---
945921
---
945921
945921
---
624-778 Solid State Reverse Switch
---
1
------
35271
---
1
---
Order (1) 35267 Clamp, (1)
982210 Washer, (1) 983544
Lockwasher and (1) 987354
Screw
624-779
Reverse Switch Clamp, Washer, Screw
and Lockwasher
22
PARTS LIST
MODELS AND VOLTAGES
No.
Req’d
Key No. Part Name
WB, WE
WF, WH
WJ
WL
WR
115-1-60 230/460 115-1-60 230/460 115-1-60 230/460 115-1-60 230/460 115-1-60 230/460
624-199 Brake Coil
1
51001
51003
51001
51003
---
51002
51001
51002
51001
51002
624-210 Rotor Assembly
includes items 624-108
and 624-112
115-1-60
includes 624-212
624-211 Stator (also order 624-113
for models WB, WE, WF, WH
1
24228
286004
24226
286000
---
---
---
---
---
---
1
24222
24221
24223
24220
---
24225
367001
24225
367001
24225
PACKAGED LUBRICANTS
Usage
TOUCH-UP PAINTS
Used in the Valustar Electric Chain Hoists
(Refer to page 12 for Lubrication Instructions)
Type
Quantity
Hoist Gears
Grease (Special)
Valustar Electric Chain Hoists and Series 635 Low Headroom Trolleys
Name
Color
Quantity*
Size
Part No.
Part No.
1/2# Can
28605
1# Can
28616
4# Can
28617
Spline on end of Drive Shafts Oil-Graphite Mixture
1 Pint Can
40628
Load Chain
Oil
1 Pint Can
28608
1 Gal. Can
28619
Lower Hook Thrust Bearing
Grease: Heavy Cup Grease - obtain locally*
Hoist
Trolley
Orange
Black
1 case
1 case
12-12 oz. Aerosol Cans
12-12 oz. Aerosol Cans
84190
84189
*Touch-up paints are only available in case quantities.
NOTE: When painting Hoists or Trolleys, also order
warning labels, identification labels, etc. that may be
coated during painting.
*These oils are not furnished by CM in packaged quantities.
When ordering lubricants, specify the type of lubricant, part number and
packaged quantity required.
CONTROL STATION
Key No.
Part Name
No. Req’d
Part No.
624-232 Control Station (Includes
624-301 thru 624-822)
624-252 Warning Label (Electrical)
1
36900B
1
24842
624-253 Manufacturer Label
1
28470
624-301 Control Station Grommet
1
36989
624-302 Control Station Housing
1
36998B
624-303 Gasket
1
36486
624-304 Control Station Button
Assembly
1
36988
624-306 Control Station Parts Kit
1
36939
624-307 Contact Assembly (Includes
624-304)
624-822 Warning Label
1
36987
1
24845
624-231
624-306
624-302
624-301
624-253
624-303
624-822
624-307
624-304
624-252
Figure 16. Control Station Exploded View
23
24
624-163
624-164
624-162
Figure 17. Valustar Electric Chain Hoist Exploded View
624-166
624-165
25
SERIES 635 LOW HEADROOM TROLLEY PARTS LIST
Figure 18. Series 635 Low Headroom Trolley Exploded View
Key No.
Part Name
No. Req’d.
1-Ton 2-Ton
624-400
Trackwheel
4
624-401
Trackwheel Stud
4
624-402
Trackwheel Stud Nut
4
624-403
Suspension Bolt
(Special Alloy Steel Bolt)
9-5/32" long*
Key No.
Part Name
4
35774
624-409
Load Bracket
4
987790 35838
3-7/16" wide*
1
1
35019
4
982520 948804
5-13/32" wide**
1
1
35024
–
4-3/16" wide†
1
1
–
35033
6-11/16" wide††
1
1
–
35043
1
1
35371
–
–
35450
50762
–
624-410
No. Req’d.
1-Ton 2-Ton
Part No.
1-Ton 2-Ton
–
Vertical Load Bar Pin
(Special Alloy Steel Pin)
10-1/4" long**
2
–
35407
–
10" long†
–
2
–
35445
2-11/16" long*
–
2
–
35414
2-7/8" long**
1
1
–
35413
3-3/4" long†
1
1
–
35400
–
††
12-1/16" long
624-404
2
Part No.
1-Ton 2-Ton
Trolley Spacer Washers
0.165" thick*
40
–
35782
–
0.125" thick**
38
–
958822
–
1/2" long*
1
1
982383
0.165" thick†
–
32
–
35783
1-1/4" long**
1
1
982386
–
0.125" thick††
–
38
–
988039
3/4" long†
1
1
–
982433
624-405
Suspension Bolt Nut
4
4
948803 958818
–
987209
624-406
Suspension Bolt Nut Cotter Pin
4
4
988343 988368
624-407
Side Frame, Plain Side
624-408
624-411
Vertical Load Bar Pin Screw
1-1/2" long††
1
1
624-412
Vertical Load Bar Pin Screw L.W.
1
1
983548 983547
624-413
Trackwheel Stud Nut L.W.
4
4
987923 987924
Without Trolley Guards***
2
2
35640
35654
624-414
Identification Label
1
1
36916
36917
Trolley Guards***
2
2
35635
35636
624-416
Trackwheel Washer
–
1
–
987903
624-417
Warning Label
1
1
Without Trolley Guards***
2
2
35640
35654
Trolley Guards***
2
2
35635
35636
Side Frame, ID Plate Side
* These items are for the 1-Ton Trolley for operation on 2.66" thru 5.64"
flange widths.
** These items are for the 1-Ton Trolley for operation on over 5.64" thru 7.00"
flange widths.
*** If side frame is equipped with spacer block, contact factory.
†
††
936984 936984
These items are for the 2-Ton Trolley for operation on 3.33" thru 6.00"
flange widths.
These items are for the 2-Ton Trolley for operation on over 6.00" thru 8.25"
flange widths.
®
Note: When ordering parts, always furnish hoist model and serial number, motor horsepower,
voltage, phase, frequency and rated capacity of hoist on which the parts are to be used.
For the location of the nearest CM Master Parts Depot, see the list located on the inside front cover.
LIMITATION OF WARRANTIES, REMEDIES AND DAMAGES
THE WARRANTY STATED BELOW IS GIVEN IN PLACE OF ALL
OTHER WARRANTIES, EXPRESS OR IMPLIED, OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, OR
OTHERWISE, NO PROMISE OR AFFIRMATION OF FACT MADE
BY ANY AGENT OR REPRESENTATIVE OF SELLER SHALL
CONSTITUTE A WARRANTY BY SELLER OR GIVE RISE TO
ANY LIABILITY OR OBLIGATION.
Seller warrants that on the date of delivery to carrier the goods are
free from defects in workmanship and materials.
SELLER’S SOLE OBLIGATION IN THE EVENT OF BREACH OF
WARRANTY OR CONTRACT OR FOR NEGLIGENCE OR
OTHERWISE WITH RESPECT TO GOODS SOLD SHALL BE
EXCLUSIVELY LIMITED TO REPAIR OR REPLACEMENT, F.O.B.
SELLER’S POINT OF SHIPMENT, OF ANY PARTS WHICH SELLER DETERMINES TO HAVE BEEN DEFECTIVE or if Seller determines that such repair or replacement is not feasible, to a refund of
the purchase price upon return of the goods to Seller.
the use of the goods if, prior to such damage, injury or loss, such
goods are (1) damaged or misused following Seller’s delivery to carrier; (2) not maintained, inspected, or used in compliance with
applicable law and Seller’s written instructions and recommendations; or (3) installed, repaired, altered or modified without compliance with such law, instructions or recommendations.
UNDER NO CIRCUMSTANCES SHALL SELLER BE LIABLE FOR
INCIDENTAL OR CONSEQUENTIAL DAMAGES AS THOSE
TERMS ARE DEFINED IN SECTION 2-715 OF THE UNIFORM
COMMERCIAL CODE.
Any action against Seller for breach of warranty, negligence or otherwise, must be commenced within one year after such cause of
action occurs.
INDEMNIFICATION AND SAFE OPERATION
Buyer shall comply with and require its employees to comply with
directions set forth in instructions and manuals furnished by Seller
and shall use and require its employees to follow such instructions
and manuals and to use reasonable care in the use and maintenance of the goods. Buyer shall not remove or permit anyone to
remove any warning or instruction signs on the goods. In the event
of personal injury or damage to property or business arising from
the use of the goods, Buyer shall within 48 hours thereafter give
Seller written notice of such injury or damage. Buyer shall cooperate
with Seller in investigating any such injury or damage and in the
defense of any claims arising therefrom.
NO CLAIM AGAINST SELLER FOR ANY DEFECT IN THE GOODS
SHALL BE VALID OR ENFORCEABLE UNLESS BUYER’S WRITTEN NOTICE THEREOF IS RECEIVED BY SELLER WITHIN ONE
YEAR FROM THE DATE OF SHIPMENT.
Seller shall not be liable for any damage, injury or loss arising out of
If Buyer fails to comply with this section or if any injury or damage is
caused, in whole or in part, by Buyer’s failure to comply with applicable federal or state safety requirements, Buyer shall indemnify and
hold Seller harmless against any claims, loss or expense for injury
or damage arising from the use of the goods.
L
! WARNING
Alterations or modifications of equipment and use of nonfactory repair parts can lead to dangerous operation and
injury.
TO AVOID INJURY:
• Do not alter or modify equipment.
• Do use only CM replacement parts.
®
Columbus McKinnon Corporation
Industrial Products Division
140 John James Audubon Parkway
Amherst, New York 14228-1197
1-800-888-0985
Fax 716-689-5644
© 2009 Columbus McKinnon Corp.
© 2002 Columbus McKinnon Corp.
Printed in USA
Printed in USA
SS 7/99