Slip-On (2015)
Installation Instructions
1.
Make sure the bike is completely cool before starting the
installation. Make sure the bike is secure on a center stand
or ideally a service lift.
2.
Remove OEM muffler heat shield.
3.
Remove OEM muffler assembly.
4.
Attach muffler to TBR slip system using the supplied hook
springs. Slide rubber lined muffler clamp and barrel clamp
on and install to bike.
5.
Loosely attach muffler to bike using the OEM bolt and nut
and install muffler clamp to inside of passenger foot peg.
7.
Before you run the bike, clean off all fingerprints and dirt, as
any oily residue will etch the metal and become somewhat
permanent when the system gets hot. Run the bike and enjoy.
It is normal for some white smoke to appear the first time you
start the bike. This is packing/manufacturing oil from inside
the pipe burning off. Check for gaps or leaks. If you find a leak,
a little high temperature silicon sealant should fix it. After 50
to 100 miles, recheck all fasteners for tightness.
Suzuki
GSX-R600 / 750
Slip-on Exhaust System with S1R Exhaust Canister
Part # 005-4180405-S1
Parts List
Care & Cleaning / Warranty
Qty. Description
Part Number
1
1
1
1
2
1
1
1
Carbon
Vertical
005-41804S
005-27-61MSH
005-S45
005-SP
031-P09175
015-10212
10” S1R
S1R Clamp with Rubber Liner
Slip Tube
61mm Barrel Clamp
Spring Hooks
Spring Puller
Anti-Seize Lubricant
TBR Sticker Kit
Care & Cleaning
Keep system free of dirt and moisture. Store in a cool, dry place. Make sure vehicle is
completely cool before maintenance.
Stainless Header System: Polished stainless steel pipes will turn a light golden hue
after a few heat cycles, this is a normal characteristic of high quality stainless steel.
Clean using a mild water based spray cleaner. Always apply cleaner or polish with a
soft, clean cloth.
6.
Check for clearance and alignment, then tighten muffler mount,
and finally barrel clamp.
Titanium Header System: Polished titanium pipes will experience color shift ranging
from deep blue/purple through amber after a few heat cycles. This is a normal
characteristic of high quality titanium. Clean using a mild water based spray cleaner.
Always apply cleaner or polish with a soft, clean cloth.
Polished Aluminum Canisters: Use an aluminum or mag wheel polish to restore the
bright finish to factory spec.
IMPORTANT - PLEASE READ CAREFULLY
We recommend that this performance part be installed by a qualified
motorcycle technician. If you have any doubts as to your ability to install this
performance part, please consult with your local motorcycle dealer. Read all
instructions first before starting installation. Make sure the motorcycle and
exhaust system are completely cool before starting the installation. Also,
make sure the bike is secure on a centerstand or ideally a service lift during
installation. Be sure to save all stock components for possible use later.
Warranty Information
Two Brothers Racing products are intended for closed course competition purposes only, and therefore
are sold “as is” without warranty. Two Brothers Racing specifically disclaims any warranties of
merchantability or fitness for a particular purpose and disclaims all responsibility for consequential and
incidental damages or any other losses arising from the use of these products or parts. Not tested for use
Brushed Aluminum Canisters: Clean using a mild water based spray cleaner. Always
apply cleaner or polish with a soft, clean cloth.
Carbon Fiber Canisters: Clean using a mild water based spray cleaner. Always apply
cleaner or polish with a soft, clean cloth. Always make sure the fiberglass packing
inside is in good condition and not burned out, as exhaust heat inside an empty canister
will deteriorate the carbon fiber sleeve.
TBR sells repack kits (Road - #005-10038, Offroad - #005-10038MX) that include
everything you need to easily do it yourself.
Titanium Mufflers: For cleaning use a mild water based spray cleaner. Always apply
cleaner or polish with a soft, clean cloth. Always make sure the fiberglass packing
inside is in good condition and not burned out, as exhaust heat inside an empty canister
will deteriorate the carbon fiber sleeve.
TBR sells repack kits (Road - #005-10038, Offroad - #005-10038MX) that include
everything you need to easily do it yourself.
Repack all road canisters every 3,000 miles. Part #005-10038
Repack all offroad canisters after every 10 hours of use. Part #005-10038MX
NEVER dyno test your bike with carbon fiber or titanium canisters installed - the
intense heat and lack of cooling air can quickly burn through the canister material. Two
Brothers Racing does not provide a warranty for burned canisters.
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement