Installation and User Guide
AG Pro Quint
TM
Selectable
700 (Band 12 / 17, 13) / 800 /
AWS (1700 / 2100) / 1900 MHz
In-Building Wireless
Smart Technology ™
Signal Booster
Contents:
Antenna Options & Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Quick Install Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Installation Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Before Getting Started . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Finding the Strongest Signal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Outside Antenna Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Installing the Inside Antenna . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Installing a Wilson Electronics Signal Booster. . . . . . . . . . . . . . . . . . . . . 9
Powering up a Wilson Electronics Signal Booster . . . . . . . . . . . . . . . . . 10
Button Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Understanding LCD Screen. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Warnings and Recommendations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Guarantee, Warranty & Specifications . . . . . . . . . . . . . . . . . Back Cover
Appearance of device and accessories may vary.
Note: This manual contains important safety and operating information. Please read and follow the
instructions in this manual. Failure to do so could be hazardous and result in damage to your Signal
Booster.
Installation Instructions for the Following Wilson
Electronic Signal Booster:
AG Pro™ Quint Selectable
700 (Band 12 / 17, 13) / 800 / AWS (1700 / 2100) / 1900 MHz
In-Building Wireless Smart Technology ™ Signal Booster
Model #273470 FCC: PWO273470
How it Works
Wilson Electronics Signal Boosters are bi-directional devices that deliver service
levels consistent with what would be expected in areas of high cell network coverage.
They amplify a weak or shadowed signal in mobile, M2M, marine and in-building
applications. When using a Wilson Electronics Signal Booster in conjunction with
Wilson Electronics antennas, the Outside Antenna will collect the cell tower signal
and send it through the cable to the Signal Booster. The signal is then amplified
and re-transmitted through the Inside Antenna into the room. Cell phones and
cellular data cards in that area then communicate with the improved signal. When
a cell phone or cellular device transmits, the signal is received by the Inside
Antenna, amplified by the Signal Booster and transmitted back to the cell tower
through the Outside Antenna.
Inside this Package
Note: Kits may contain different accessories
AC/DC
Power Supply
12V / 3A
Signal
Booster
(859900)
Outdoor Antenna Options & Accessories
1. Wide Band Directional Antenna 700 - 2700 MHz
(304411) Note: The Outside fixed Antenna must be
connected with a minimum of 26’ of RG58 coax
cable (950630).
2. Pole Mount Wide Band Panel Antenna (304453)
1
Indoor Antenna Options & Accessories
A. Wide-Band Panel Antenna 700-2700 MHz
(multiple mounting options available)
B. 50 Ohm Lightning Surge Protector N Connector
(859902)
Splitter options on page 9
2
A
B
Appearance of device and accessories may vary.
To purchase, call Wilson Electronics Sales Department at: 800-204-4104
We recommend using directional antennas with this Signal Booster.
1
Contact Wilson Electronics Technical Support Team with any questions at 866-294-1660
or email: [email protected] Mon.- Fri. Hours: 7 am to 6 pm MST.
Quick Install Overview
See Installation Diagram on page 3 & 4. Contact Wilson Electronics
Technical Support Team with any questions at 866-294-1660.
1. Select a location to install the Signal Booster that is away from excessive heat,
direct sunlight, moisture and has proper ventilation. Do not place the Signal
Booster in an air-tight enclosure.
2.
Select a location on the roof of the building to install the Outside Antenna. Use a cell
phone in test mode to find the strongest signal from the cell tower. Refer to page 7.
Visit www.WilsonElectronics.com to find the test mode function for your particular cell
phone.
3.
Run the Outside Antenna cable to the Signal Booster and attach it to the connector
labeled “Outside Antenna” on the Signal Booster. Refer to page 8 for more
information on running cable. Lightning Surge Protection is recommended for all inbuilding installations refer to page 6.
4. Select a location for the Inside Antenna, preferably in the center of where the
signal needs to be amplified. A minimum separation distance of 20 vertical feet
(within the null zone) or 50 horizontal feet is necessary for proper operation.
If the inside coverage is not sufficient you may need as much as 75 feet of
horizontal separation (refer to installation diagram on pages 3 & 4). Run the
Inside Antenna cable to the Signal Booster and attach it to the connector labeled
“Inside Antenna” on the Signal Booster.
5. Before powering up the Signal Booster, verify that both the Outside Antenna and
the Inside Antenna are connected and check that all connections are tight. Refer
to page 9. Note: Be careful when plugging the connectors in so as not to bend
the center pins on the connectors.
6. If the light is not green, please refer to pages 10 & 12.
Warning: Connecting the Signal Booster directly to a cell phone with use of
an adapter will damage the cell phone and/or the Signal Booster.
IMPORTANT NOTICE
• It is very important to power your Signal Booster using a
surge protected AC Power Strip with at least a 1000 Joule
rating.
• Failure to do this will void your warranty in the event of a
power surge or lightning strike.
Contact Wilson Electronics Technical Support Team with any questions at 866-294-1660
or email: [email protected] Mon.- Fri. Hours: 7 am to 6 pm MST.
2
Installation Diagram
Outside Antenna
O
Ou
(Panel Antenna shown)
(Pa
Inside Antenna
Preferred Method: Place the Inside
Antenna in the ceiling facing down for
the best coverage.
Note: The Inside Antenna may be
mounted on the wall directly under the
Outside Antenna, in the null zone, if
20 feet of vertical separation can be
maintained.
Null Zone: The area under the
Outside Antenna, where the
Outside Antenna radiates the
least.
Note: A Lightning Surge Protector is
recommended for all building installations
(sold separately). Make sure the protector
is installed in line between the Outside
Antenna and the Signal Booster.
Inside Antenna
(Optional
second
antenna for
additional
coverage).
Power
Supply
Typical Installation
3
Contact Wilson Electronics Technical Support Team
am with any questions at 866-294-1660
or email: [email protected] Mon.- Fri.
F i Hours:
H
7 am to
t 6 pm MST.
MST
Before Getting Started
This guide will help you properly install your Wilson Electronics Signal Booster. It
is important to read through all of the installation steps for your particular
application prior to installing any equipment. Read through the instructions,
visualize where all the equipment will need to be installed and do a soft
installation before mounting any equipment. Contact Wilson Electronics Technical
Support with any questions at: 866-294-1660.
Splitter (2-way, 3-way or
4-way if using multiple
inside antennas)
Lightning
Surge Protector
(recommended)
Inside Antenna
(Optional
third antenna
for additional
coverage)
Signal
Booster
Surge Protector
Power Strip
Contact Wilson Electronics Technical Support Team with any questions at 866-294
866-294-1660
294-1660
or email:
il [email protected]
t [email protected] il
l t i
Mon.M
Fri.
F i Hours:
H
7 am tto 6 pm M
MST.
ST
4
Reasons for Weak Cellular Signals
Anyone who uses a cell phone or cellular data card knows the frustration of not
being able to connect to or maintain a strong cellular signal. When this occurs, it is
generally due to one of two reasons:
1. Location of the Nearest Cell Tower – Cell towers are situated to provide broad
coverage; however, there are many areas in which signal strength may be
reduced by topographic features or by local government restrictions on the
height or placement of the towers themselves. Rural areas generally have
fewer cell towers than urban regions.
2. Natural and Man-Made Obstructions – Signal strength can also be negatively
affected by trees, hills, buildings, weather, and other obstructions. You may be
relatively close to a cell tower but still unable to make a call. This often occurs
in homes, offices and other buildings in which stucco, concrete or metal walls
may block the signal.
The Signal Booster works with two antennas. The Inside Antenna communicates
with your cell phone and the Outside Antenna communicates with the cell tower.
The Outside Antenna receives the cell tower signal and sends it through the cable
to the Signal Booster, where it is amplified and transmitted through the Inside
Antenna into the room. When the Inside Antenna picks up a signal from your
cellular device, the Signal Booster amplifies that signal and transmits it through
the cable, then through the Outside Antenna and back to the cell tower.
Note: The Signal Booster will only operate if there is an adequate signal to amplify.
Wide Band Antenna
Cell Tower
Selecting a Direction for the Outside Antenna
Use a cell phone in test mode to find the strongest signal from the cell tower
(refer to page 7 for more information). To get the strongest signal possible, it
is very important to set up your Outside Antenna properly. The Inside and the
Outside Antenna must be mounted in such a way that they are able to pick up
the best possible cell signal on the outside of the building and provide the best
possible signal on the inside of the building. Mount the Outside Antenna as
high as possible facing the cell tower in an area with the best possible signal
coverage.
5
Contact Wilson Electronics Technical Support Team with any questions at 866-294-1660
or email: [email protected] Mon.- Fri. Hours: 7 am to 6 pm MST.
Note: Never point the front of a directional antenna toward the Inside
Antenna. See Figures 1 & 2 on page 10.
Finding the Strongest Signal
When installing your Signal Booster’s Outside Antenna, aiming it towards
the best signal source from you service provider is important. The best way
of getting the strongest signal is to have one person on the roof to rotate the
Outside Antenna, which is connected to the Signal Booster. Turn the Outside
Antenna about 45 degrees at a time, while the second person is watching the
signal strength on the phone inside the building. This allows you to read the
signal strength from the cell tower. It is preferable to have the phone in the
test mode so the actual signal strength can be read, as bars are not the most
accurate. Go to www.WilsonElectronics.com for help in finding the test mode for
your phone. Always make sure the person inside the building gives the signal
time to arrive and register on the phone (between 10-30 seconds for phone to
reset to the signal reading).
Cell Signal
Outside
Panel
Antenna
Cell Tower
Signal readings usually appear as a negative number (for example, -86). The
closer you get to zero the stronger the signal. (See graph below).
Signal Strength Graph
EXCELLENT
-50dB
-60dB
GOOD
-70dB
-80dB
POOR
-90dB
-100dB
NO
SIGNAL
-110dB
Contact Wilson Electronics Technical Support Team with any questions at 866-294-1660
or email: [email protected] Mon.- Fri. Hours: 7 am to 6 pm MST.
6
Outside Antenna Installation
The antenna should be mounted as shown in the illustration on page 5. The
mounting bracket, included with antenna, is adjustable and will accommodate
pipe diameters from 1.25” to 2” (pipe sold separately #901117). Mount the
antenna so that there is at least 3 feet of clearance in all directions around
it. Position the antenna so that it has an unobstructed line of sight to the cell
tower’s strongest signal. Make sure the antenna is not pointing across your own
roof or at the Inside Antenna as this will cause the oscillation protection circuitry
to shut down the Signal Booster.
Warning: The Outside fixed Antenna must be connected with a minimum of
26 feet of RG58 coax cable.
Warning: Lightning protection is recommended for all installations
(#859902-50 Ohm shown below). Take extreme care to ensure
that neither you nor the antenna comes near any electric power
lines.
Installing Lightning Protection (sold separately)
Install the Lightning Surge Protector
(LSP) close to the Signal Booster. Attach
the cable from the Outside Antenna to
the surge protector, using a short length
Lightning
of low loss cable; attach one end to the
LSP and the other to the Outside Antenna Surge Protector
(sold separately)
connector on the Signal Booster. Ensure
the LSP is properly grounded (ground
(not included)
wire not included). LSP sold separately,
go to www.WilsonElectronics.com or call
To Inside
800-204-4104 to order.
To Outside
Antenna
Ground Wire
(not included)
To Signal
Booster
Antenna
Signal Booster
Surge Protector Power Strip
7
Contact Wilson Electronics Technical Support Team with any questions at 866-294-1660
or email: [email protected] Mon.- Fri. Hours: 7 am to 6 pm MST.
Mounting Tips for Running Outside Antenna Cable
If you are mounting the Outside Antenna on the roof of your building, we have
found that it is easiest to run your cable underneath the down side of your roof’s
flashing. If you have satellite TV service installed you may be able to follow the
same route as the satellite TV cables that are already running from outside of your
building to the inside.
After routing the cable, we recommend sealing any areas where the cable passes
into the building with cable bushings, silicone or a silicone-type sealant to keep
your installation from leaking. If you are mounting the Outside Antenna to the
outside wall of your home or building, the simplest way is to run the cable on the
outside of the wall and attach it to the exterior of your home or office. Then drill
a hole through the wall where you want the cable to appear on the inside of the
building. Before drilling, make sure that there are no electrical outlets, sewer or
water pipes, or electrical wiring in the wall that you are about to drill through as this
could potentially harm you or damage the building.
After drilling the required hole, run the cable through and seal it with cable
bushings or a silicone-type sealant to enclose the hole that you have created. In
some instances, it may be possible to run the cable up into the fascia of the attic
overhang. In this circumstance, the cable will be accessible in the attic for further
routing.
Installing the Inside Antenna
(Instructions are for optional Inside Panel Antenna)
Select a location for the Inside Antenna, preferably in the center of where the
signal needs to be amplified. A minimum separation distance of 20 vertical feet
(within the null zone) or 50 horizontal feet is necessary for proper operation.
If the inside coverage is not sufficient you may need as much as 75 feet of
horizontal separation. Refer to installation diagram on pages 3 & 4.
Inside
Antenna
Ceiling
Rafters
Ceiling
Drywall
Contact Wilson Electronics Technical Support Team with any questions at 866-294-1660
or email: [email protected] Mon.- Fri. Hours: 7 am to 6 pm MST.
8
In some cases, multiple Inside Antennas may be required, for instance if you
have multiple rooms with poor signal. A signal may be split by using a splitter
(sold separately). Refer to the configuration on pages 3 & 4.
Optional Wide Band
Inside Antenna
(sold separately)
Splitter Options:
Multiple mounting
options available
2-way
3-way
4-way
(859957)
(859980)
(859981)
Installing a Wilson Electronics Signal Booster
Select a location to install the Signal Booster that is away from excessive heat,
direct sunlight, moisture and that has proper ventilation. Do not place the Signal
Booster in an air-tight enclosure. Recommended installation locations for inbuilding Signal Boosters are near a power outlet and in a closet or on a shelf.
Note: It is important to have adequate air ventilation. Maintain at least 6 inches
of clearance from surrounding objects. Be careful when plugging the
connector in so as not to damage the center pins on the connectors.
Run the Outside Antenna cable to the Signal Booster and attach it to the
connector labeled “Outside Antenna” on the Signal Booster. Run the Inside
Antenna cable to the Signal Booster and attach it to the connector labeled “Inside
Antenna” on the Signal Booster.
Note: For distances of 20 feet or more, use Wilson low loss cable.
Note: It is very important to power your Signal Booster using a surge protected AC
Power Strip with at least a 1000 Joule rating. Failure to do this will void your
warranty in the event of a power surge or lightning strike.
Warning: An Inside Antenna must have a separation distance from all
persons that is at least 8 inches for the Panel Antenna.
9
Contact Wilson Electronics Technical Support Team with any questions at 866-294-1660
or email: [email protected] Mon.- Fri. Hours: 7 am to 6 pm MST.
CORRECT INSTALLATION
Point antennas away from each other
Inside Panel
Antenna
Outdoor
Antenna
Signal Booster
Figure 1
INCORRECT INSTALLATION
Never point antennas toward each other
Inside Panel
Antenna
Outdoor
Antenna
Signal Booster
Figure 2
Powering up a Wilson Electronics
Signal Booster
1. Never point the front of a directional Outside Antenna toward the Inside
Antenna. Refer to Figures 1 & 2 above.
2. Ensure that both the Outside Antenna cable and the Inside Antenna cable
are connected to the Signal Booster and the connections are tight before
powering up the Signal Booster.
3. Plug the power supply into the Signal Booster input marked “POWER”
(carefully, to avoid damaging the center pin) and then into a surge protected
AC Power Strip.
4. If the Signal Booster does not have green lights, please refer below.
5. Using multiple Signal Boosters in one installation could cause interference to
the cell tower.
6. Contact Wilson Electronics Technical Support Team with any questions at
866-294-1660 or email [email protected] Technical Support hours
are Mon.- Fri. 7 am to 6 pm MST.
Button Operation 1
1 FACTORY RESET – Pushing and holding the “Reset” button for 5 seconds will
reset the Signal Booster to max gains.
Note: If the Signal Booster is unplugged, a similar situation will occur, except the
manual gains will remain the same as they were before being unplugged.
Contact Wilson Electronics Technical Support Team with any questions at 866-294-1660
or email: [email protected] Mon.- Fri. Hours: 7 am to 6 pm MST.
10
2 BAND SELECT – Pressing the “Band Select” button will cycle through the
bands. If “700” is selected, holding the “Band Select” button for 3 seconds will
switch between bands 12/17 and 13.
3 UP – Controls the manual gain adjustment.
a. Pressing the “UP” (refer to Figure 3) button will cause the selected gain to
increase in 1dB increments.
b. Gains will never go higher than the maximum (70dB or 75dB).
c. Holding the “UP” button on the initial plug-in will turn all of the manual gains to
maximum (70 dB or 75 dB) to aid the installer during setup.
Figure 3
3
PUSH UP
GAIN
4
PUSH DOWN
OVERLOAD
62 AA’ 72
Band
PUSH
Select
2
Reset PUSH
1
4 DOWN – Controls the manual gain adjustment.
a. Pressing the “DOWN” (refer to Figure 3) button will cause the selected gain to
decrease in 1dB increments.
b. Gains will never go lower than the minimum (40 dB or 45 dB).
c. Holding the “DOWN” button on the initial plug-in will turn all of the manual
gains to minimum (40dB or 45dB) to aid the installer during setup.
Understanding the LCD Screen
1. Five Bands can be individually selected:
a 700 B12 (AT&T®) = Band 12/17 (LTE)
Hold “Band Select” for 3 seconds while in
700 if B12 is not selected.
A700 AB12
AOK
b 700 B13 (Verizon™) = Band 13 (LTE)
Hold “Band Select” for 3 seconds while in
700 if B13 is not selected.
11
A700 AB13
AOK
Contact Wilson Electronics Technical Support Team with any questions at 866-294-1660
or email: [email protected] Mon.- Fri. Hours: 7 am to 6 pm MST.
c 800 – Band 5 (AMPS)
A800
d 1900 – Band 2 (PCS)
APCS
AOK
e 1700/2100 – Band 4
(AWS)
AAWS
AOK
AOK
2. When a band is selected, using the “Band Select” button, manual gains can
be changed from a maximum of 70dB / 75dB to a minimum of 40dB / 45dB by
using the UP and DOWN buttons.
3. An ORANGE light and “OVL” in the bottomright corner of the LCD screen of the frequency
that is receiving an overload signal (refer to
Figure 4) indicates that one or more of the
frequencies has been turned off (or reduced)
due to receiver overload. This reduction is
to prevent the disruption of cell towers. The
“Band Select” button must be pressed to cycle
through the frequencies to find the Band that
has the overload. Press the “DOWN” button to
decrease the gain until you have an “OK” on
the bottom-right corner of the LCD screen. The
Signal Booster is now working with reduced
gain. More than one frequency can overload at
the same time. If one frequency is reduced and
an OVERLOAD exists on another band, the
light will remain orange. Repeat the process for
all frequencies until a green light and “OK” are
achieved. Contact Wilson Electronics Technical
Support Team for assistance: 866-294-1660.
S
OVL
Figure 4
S
OSC
Figure 5
4. A RED light and “OSC” in the bottom-right corner of the LCD screen (refer to
Figure 5) indicates that the Signal Booster has shut down to prevent an oscillation,
most likely caused by the Inside and Outside Antennas being physically too close
to each other. Without this patented protection, oscillations could be transmitted to
the cell tower, blocking calls to and from the cell tower. Oscillation occurs just like
in an audio system when you put a microphone next to a speaker and get a big
squeal. When the Inside Antenna is too close to the Outside Antenna, the same
type of oscillation occurs.
Contact Wilson Electronics Technical Support Team with any questions at 866-294-1660
or email: [email protected] Mon.- Fri. Hours: 7 am to 6 pm MST.
12
During an oscillation, the Signal Booster will automatically select the first
frequency that was found to oscillate. The oscillation on the corresponding
frequency must be removed before another frequency can be selected. If a
second frequency is found to oscillate, the Signal Booster will automatically
select that frequency. All oscillations must be removed before the Signal Booster
will operate properly. If the Signal Booster has a red light and “OSC” is displayed
in the bottom-right corner, the following procedures need to be done:
a To check your cables and connections, unplug the power cord, then remove
the coax cables from the two connectors of the Signal Booster. Plug the
Signal Booster back in and adjust the gains to minimum by holding the
“DOWN” button. You should now have a green light (if not, call Wilson
Electronics Technical Support). When the green light is achieved, unplug the
power supply, reconnect the coax cables to the Signal Booster, tighten all
connections and plug the power supply back in.
b From minimum gain (40 / 45 dB) increase the gain on each frequency by
pressing the “UP” button until you get a red light, then press the “DOWN”
button 1-2 times to achieve a green light (for example, it may be at 50 dB for
the red light). If your coverage area is to low, the Outside Antenna needs to
be pointed at the cell tower with its back to the Inside Antenna. The Inside
Antenna needs to have its back facing the back of the Outside Antenna (the
Wilson Logo indicates the front of the antenna). Without proper orientation
of the antennas, you will not be able to get maximum gain from the Signal
Booster. You may need to separate the antennas further apart to get the
necessary gain* for the system to give maximum coverage and a green light.
The lower the gain the less coverage area you will have.
*Note: If the antennas cannot be sufficiently separated, the Signal Booster will
have to operate with reduced performance by decreasing the gain(s) until a
green light (OK on the LCD screen) is obtained.
Warnings and Recommendations
Warning: The Outside Antenna must always be located so the back or side
points to the Inside Antenna. Never point the front of the Outside
Antenna toward the Inside Antenna – this is to prevent oscillation.
Warning: Connecting the Signal Booster directly to the cell phone with use of
an adapter will damage the cell phone and/or Signal Booster.
Warning: Use only the correct Wilson Electronics power supply. Use of a
non-Wilson Electronics product may damage your equipment.
13
Contact Wilson Electronics Technical Support Team with any questions at 866-294-1660
or email: [email protected] Mon.- Fri. Hours: 7 am to 6 pm MST.
Warning: RF Safety: All inside antennas used with this Signal Booster
may not have gain (less cable loss) that exceeds 10.1 dBi and
must be located at least 8 inches from all people. Outside fixed
antennas may not have gain that exceeds 2.8 dBi (less cable loss)
and must be located least 27 inches from all people. The outside
fixed antenna must be connected with a minimum of 26 feet of
RG58 coaxial cable. All antennas shown on page one meet these
requirements.
Warning: Verify that both the Outside Antenna and the Inside Antenna are
connected to the Signal Booster before powering up the Signal
Booster.
Recommendation: Omni Directional Antennas are not recommended with this
Signal Booster.
Recommendation: Lightning Surge Protection is recommended for all in- building
installations.
This device complies with Part 15 of FCC rules. Operation is subject to two conditions: (1) This device may not cause harmful
interference, and (2) this device must accept any interference received, including interference that may cause undesired
operation. Changes or modifications not expressly approved by Wilson Electronics could void the authority to operate this
equipment.
About Wilson Electronics
Wilson Electronics, Inc. has been a leader in the wireless communications industry
for over 40 years. The company designs and manufactures Signal Boosters,
antennas and related components that significantly improve cellular telephone signal
reception and transmission in a wide variety of applications, both mobile (marine,
RV, vehicles) and in-building (home, office, M2M).
With extensive experience in antenna and Signal Booster research and design, the
company’s engineering team uses a state-of-the-art testing laboratory, including
an anechoic chamber and network analyzers, to fine-tune antenna designs and
performance. For its Signal Boosters, Wilson Electronics uses a double electrically
shielded RF enclosure and cell tower simulators for compliance testing.
Wilson Electronics Signal Boosters feature patented Smart Technology ™ that
enables them to automatically adjust their power based on cell tower requirements.
By detecting and preventing oscillation (feedback), signal overload and interference
with other users, these Smart Technology ™ Signal Boosters improve network cell
phone areas without compromising carrier systems.
All products are engineered and assembled in the company’s 55,000-square-foot
headquarters in St. George, Utah. Wilson Electronics has product dealers in all 50
states as well as in countries around the world.
Contact Wilson Electronics Technical Support Team with any questions at 866-294-1660
or email: [email protected] Mon.- Fri. Hours: 7 am to 6 pm MST.
14
30-Day Money-Back Guarantee
All Wilson Electronics products are protected by Wilson Electronics 30-day money-back guarantee. If for any reason
the performance of any product is not acceptable, simply return the product directly to the reseller with a dated proof of
purchase.
2-Year Warranty
Wilson Electronics Signal Boosters are warranted for two (2) years against defects in workmanship and/or materials.
Warranty cases may be resolved by returning the product directly to the reseller with a dated proof of purchase.
Signal Boosters may also be returned directly to the manufacturer at the consumer’s expense, with a dated proof of
purchase and a Returned Material Authorization (RMA) number supplied by Wilson Electronics. Wilson Electronics
shall, at its option, either repair or replace the product. Wilson Electronics will pay for delivery of the repaired or replaced
product back to the original consumer if located within the continental U.S.
This warranty does not apply to any Signal Booster determined by Wilson Electronics to have been subjected to
misuse, abuse, neglect, or mishandling that alters or damages physical or electronic properties.
Failure to use a surge protected AC Power Strip with at least a 1000 Joule rating will void your warranty.
RMA numbers may be obtained by contacting Technical Support at 866-294-1660.
Disclaimer : The information provided by Wilson Electronics, Inc. is believed to be complete and accurate.
However, no responsibility is assumed by Wilson Electronics, Inc. for any business or personal losses arising from
its use, or for any infringements of patents or other rights of third parties that may result from its use.
Copyright © 2013 Wilson Electronics, Inc. All rights reserved.
U.S. Patent Nos. – 7,221,967; 7,729,669; 7,486,929; 7,409,186; 7,783,318; 7,729,656
Signal Booster Specifications
AG Pro Quint Selectable
Model Number
273470
Antenna connectors
N-Female
Antenna Impedance
50 Ohms
Dimensions
8.875 x 6.0 x 1.5 inch (22.5 x 15.2 x 3.8 cm)
Weight
2.8 lbs (1.270 kg)
Frequency
3
698-746 MHz / 746-787 MHz / 824-894 MHz / 1850-1990 MHz / 1710-2155 MHz
Power output for single cell phone (dBm)
Uplink
Downlink
Noise Figure (typical downlink/uplink)
Isolation
700 A MHz
700 V MHz
800 MHz
1900 MHz
1700/2100 MHz
29.1
23.7
28.4
23.7
29.1
22.7
29.1
22.8
27.1
22.8
5 dB nominal
> 90 dB
Power Requirements
110-240 V AC, 50-60 Hz, 20 W
Notes: 1. Nominal gain is the maximum gain at any frequency in the passband.
2. Nominal bandwidth is the difference between two frequencies that are adjacent to the passband where the amplification is 20 dB lower than the passband amplification. One of the frequencies is lower
than the passband and the other is higher.
3. The Manufacturer’s rated output power of this equipment is for single carrier operation. For situations when multiple carrier signals are present, the rating would have to be reduced by 3.5 dB, especially
where the output signal is re-radiated and can cause interference to adjacent band users. This power reduction is to be by means of input power or gain reduction and not by
an attenuator at the output of the device.
4. The maximum power for 2 or more simultaneous signals will be reduced by 6 dB every time the number of signals is doubled.
3301 East Deseret Drive, St. George, UT 84790
For additional Technical Support visit www.WilsonElectronics.com
or email at: [email protected]
Phone: 866-294-1660 Local: 435-673-5021 Fax: 435-656-2432
www.twitter.com/WilsonCellular
www.facebook.com/WilsonCellular
111102_Rev06_02.19.13
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement