Operation Manual 9,874 KB
MODEL
LC-32A33X
LC-37A33X
LCD COLOUR TELEVISION
OPERATION MANUAL
32A33X_Cover.indd 1
2008-1-8 10:46:43
Blank page
32A33X_Cover2.indd 2
2008-1-4 20:18:36
OPERATION MANUAL
Dear SHARP customer
Thank you for your purchase of the SHARP LCD colour TV product. To ensure safety and many years of
trouble-free operation of your product, please read the Important Safety Precautions carefully before
using this product.
Contents
Introduction
Dear SHARP customer ................................................................................................ 1
Contents ....................................................................................................................... 1
Important Safety Precautions ..................................................................................... 4
Supplied accessories .................................................................................................. 5
Trademarks .................................................................................................................. 5
Preparation
Attaching the stand ..................................................................................................... 6
Part names ................................................................................................................... 7
TV (Front) .......................................................................................................... 7
TV (Rear) ........................................................................................................... 8
Remote control unit.......................................................................................... 9
Before turning on the power ..................................................................................... 10
Connecting external devices .................................................................................... 11
Connecting a VCR, game console or camcorder .......................................... 11
Connecting a DVD player ............................................................................... 11
Connecting a Digital TV STB (Set Top Box) ................................................... 12
Connecting a PC ............................................................................................ 12
Inserting the batteries ............................................................................................... 13
Using the remote control unit ................................................................................... 13
Cautions regarding the remote control unit ................................................... 13
Turning the TV on/off................................................................................................. 14
Turning on the power ..................................................................................... 14
Turning off the power ..................................................................................... 14
About Menu operations ............................................................................................. 15
What is Menu? ............................................................................................... 15
Basic Menu operations .................................................................................. 15
About Guide Display ...................................................................................... 15
TV/AV input mode menu items ...................................................................... 16
PC input mode menu items ........................................................................... 17
Watching TV
Setting channels automatically ................................................................................ 18
Selecting programmes .............................................................................................. 19
Adjusting the volume ................................................................................................. 19
Menu language settings ............................................................................................ 19
Setting channels to your preference........................................................................ 20
Auto search .................................................................................................... 20
Manual setting for each channel .................................................................... 20
Sorting programmes ...................................................................................... 22
Erasing programmes ...................................................................................... 23
Labelling programmes ................................................................................... 23
Useful viewing functions ........................................................................................... 24
Split-screen viewing ...................................................................................... 24
Returning to the previously selected channel ................................................ 25
Muting the audio temporarily ......................................................................... 25
Outputting only audio..................................................................................... 25
Switching the analogue audio format ............................................................ 26
1
32A33X_en_a.indd 1
2008-1-4 20:13:04
Contents
Watching TV (Continued)
Reducing the start-up time ........................................................................... 26
Password setting for the child lock (for TV input mode) ................................ 27
Energy conservation settings ................................................................................... 28
Auto power-off at a designated time ............................................................. 28
Auto power-off after the end of broadcast .................................................... 28
Auto power-off when there are no operations performed ............................. 28
Power Management ....................................................................................... 29
Ecology ......................................................................................................... 29
Picture size settings .................................................................................................. 30
Selecting the Wide Screen Signalling (WSS) picture size automatically ........ 30
Selecting the Wide Screen Signalling (WSS) picture size manually ............... 30
Selecting the picture size manually ................................................................ 31
Selecting a preset AV MODE .................................................................................... 32
Manual picture settings............................................................................................. 33
Picture adjustment ......................................................................................... 33
Advanced picture settings ............................................................................. 34
Other picture settings................................................................................................ 35
DNR (Digital Noise Reduction) ....................................................................... 35
Adjusting the image position.......................................................................... 35
Game Play Time ............................................................................................ 35
Audio adjustment ....................................................................................................... 36
Output Volume Select ................................................................................... 36
Settings when using external devices
Settings when using HDMI output devices ............................................................. 37
Selecting the input source and signal type ............................................................ 38
Selecting input source ................................................................................... 38
Selecting input signal type ............................................................................ 38
Labelling input sources ............................................................................................. 39
Skipping HDMI/PC input .......................................................................................... 39
Colour system settings ............................................................................................. 39
AQUOS LINK
Controlling HDMI devices using AQUOS LINK ....................................................... 40
AQUOS LINK connection .......................................................................................... 41
Connecting an AQUOS BD Player/AQUOS Recorder via the AQUOS
AUDIO ........................................................................................................ 41
Connecting an AQUOS BD Player/AQUOS Recorder only ............................ 41
AQUOS LINK Setup ................................................................................................... 41
AQUOS LINK Auto power on ......................................................................... 41
Selecting recorder .......................................................................................... 42
Operating an AQUOS LINK device ........................................................................... 42
Listening with the 1 BIT THEATER RACK SYSTEM (AQUOS AUDIO) ........... 42
Listening with the AQUOS TV speaker system .............................................. 43
Manually changing the AQUOS Audio speaker system’s sound mode ......... 43
Playback of titles using AQUOS LINK............................................................ 43
Selecting media type for CEC-compatible recorder ...................................... 44
HDMI device selection ................................................................................... 44
Recording via the AQUOS Recorder EPG (only for recorders) ...................... 44
Connecting a PC
Displaying a PC image on the screen ...................................................................... 45
Selecting the picture size ............................................................................... 46
Adjusting the PC image automatically ........................................................... 47
Adjusting the PC image manually .................................................................. 47
Input resolution settings ........................................................................................... 48
Selecting the input resolution......................................................................... 48
2
32A33X_en_a.indd 2
2008-1-4 20:13:05
Contents
Connecting a PC (Continued)
PC Control of the TV .................................................................................................. 49
PC compatibility chart ............................................................................................... 50
RS-232C commands list ............................................................................................ 50
Teletext function
About Teletext ............................................................................................................ 51
Displaying Subtitles ................................................................................................... 52
Displaying Subpages ................................................................................................. 52
Teletext language setting.......................................................................................... 53
Appendix
Troubleshooting ......................................................................................................... 54
Error messages about recording using AQUOS LINK ........................................... 55
Reset ........................................................................................................................... 56
Specifications............................................................................................................. 57
Optional accessory ................................................................................................... 57
Dimensional drawings ............................................................................................... 58
Mounting the TV on the wall .................................................................................... 60
Removing the stand ...................................................................................... 60
Handling and precautions with the wall-mounted TV ................................... 60
CLEARING THE PASSWORD .................................................................................... 61
3
32A33X_en_a.indd 3
2008-1-4 20:13:05
Important Safety Precautions
• Cleaning — Unplug the AC cord
from the AC outlet before cleaning
the product. Use a damp cloth to
clean the product. Do not use liquid
cleaners or aerosol cleaners.
• Water and moisture — Do not use
the product near water, such as
bathtub, washbasin, kitchen sink,
laundry tub, swimming pool and in a
wet basement.
• Do not place vases or any other
water-filled containers on this product.
The water may spill onto the product
causing fire or electric shock.
• Stand — Do not place the product
on an unstable cart, stand, tripod
or table. Doing so can cause the
product to fall, resulting in serious
personal injuries as well as damage
to the product. Use only a cart,
stand, tripod, bracket or table
recommended by the manufacturer
or sold with the product. When
mounting the product on a wall, be
sure to follow the manufacturer’s
instructions. Use only the mounting
hardware recommended by the
manufacturer.
• When relocating the product
placed on a cart, it must be moved
with utmost care. Sudden stops,
excessive force and uneven floor
surface can cause the product to fall
from the cart.
• Ventilation — The vents and other
openings in the cabinet are designed
for ventilation. Do not cover or block
these vents and openings since
insufficient ventilation can cause
overheating and/or shorten the life
of the product. Do not place the
product on a bed, sofa, rug or other
similar surface, since they can block
ventilation openings. This product is
not designed for built-in installation;
do not place the product in an
enclosed place such as a bookcase
or rack, unless proper ventilation
is provided or the manufacturer’s
instructions are followed.
• The LCD panel used in this product
is made of glass. Therefore, it can
break when the product is struck
forcefully or with a sharp object. If
the LCD panel is broken, be careful
not to be injured by broken glass.
• Heat sources — Keep the product
away from heat sources such as
radiators, heaters, stoves and other
heat-generating products (including
amplifiers)
• To prevent fire, never place any type
of candle or naked flames on the
top or near the TV set.
• To prevent fire or shock hazard, do
not place the AC power cord under
the TV set or other heavy items.
• Do not place heavy objects on this
product or stand on it. Doing so
could cause injury if the product
overturns. Take special care near
children and pets.
The LCD panel is a very high technology product
with 1,049,088 thin film transistors, giving you fine
picture details.
Due to the very large number of pixels, occasionally
a few non-active pixels may appear on the screen
as a fixed point of blue, green or red.
This is within product specifications and does not
constitute a fault.
Precautions when
transporting the TV
Be sure to always carry the TV
by two people holding it with two
hands — one hand on each side
of the TV.
• Do not display a still picture for a long time, as this could
cause an afterimage to remain.
• Install the product on the place where the AC cord can
be unplugged easily from the AC outlet, or from the AC
INPUT terminal on the rear of the product.
4
32A33X_en_b.indd 4
2008-1-4 20:13:34
Supplied accessories
Make sure the following accessories are provided with the product.
Remote control unit
Used with batteries inserted.
Page 9
“AAA” size battery (g2)
Page 13
Cable clamp
AC cord
Always use the AC cord supplied with
the TV.
Page 10
Stand unit
Stand base
Stand post
Short screws (g9)
Hex key
Cloth
For bundling cables.
Put all parts of the stand unit together and then attach it to the TV.
Page 10
Page 6
Operation manual
Trademarks
• “HDMI, the HDMI logo and High-Definition Multimedia Interface are trademarks or registered trademarks of HDMI
Licensing LLC.”
5
32A33X_en_b.indd 5
2008-1-10 8:28:22
Preparation
Attaching the stand
• Before attaching (or detaching) the stand, unplug the AC cord from the AC INPUT terminal.
• Before performing work spread cushioning over the base area to lay the TV on. This will prevent it from being
damaged.
CAUTION
• Attach the stand in the correct direction.
• Be sure to follow the instructions. Incorrect installation of the stand may result in the TV falling over.
1
Confirm the screws supplied with the TV.
Screws (g4)
(used in step 3)
3
Screws (g5)
(used in step 2)
1 Insert the stand into the openings on the
bottom of the TV.
2 Insert and tighten the 4 screws into the 4
holes on the rear of the TV.
Hex key
2
Attach the supporting post for the stand unit
onto the base as shown below.
Screw
Screw
Soft
cushion
Hex
key
NOTE
• To detach the stand, perform the steps in reverse order.
6
32A33X_en_b.indd 6
2008-1-10 8:28:24
Preparation
Part names
TV (Front)
TV/VIDEO button
Channel up (r)/down (s) buttons
MENU button
Volume up (e)/down (f) buttons
POWER (On/Off) button
Remote control sensor
OPC indicator*
OPC sensor
SLEEP timer indicator
POWER indicator**
*OPC: Optical Picture Control (See page 33.)
** See page 14 for the TV status indicator.
• The illustrations and on-screen displays in this operation manual are for explanation purposes and may vary slightly from the
actual operations.
• The illustrations used throughout this manual are based on LC-37A33X.
7
32A33X_en_b.indd 7
2008-1-4 20:13:36
Preparation
TV (Rear)
AC INPUT terminal
INPUT 3 (HDMI) terminals
RS-232C terminal
INPUT 4 (HDMI) terminal
INPUT 5 (PC) terminals
Headphone jack
INPUT 1 terminals
MONITOR OUTPUT
terminals
Antenna input terminal
INPUT 2 terminals
Regarding the headphone jack
• Use headphones with a stereo mini plug (Ø 3.5 mm).
• Be sure to unplug headphones from the jack when they are not
in use.
• The speakers do not output volume when headphones are
plugged in.
• The “Audio” menu cannot be operated when headphones are
plugged in.
• You can set the volume to different levels for each input source.
Volume display when headphones are plugged in
20
8
32A33X_en_b.indd 8
2008-1-10 8:28:24
Preparation
Remote control unit
6
7
1
13
8
9
10
2
11
3
14
4
5
6
7
8
9
10
15
16
17
18
19
20
21
22
11
23
24
12
13
14
12
15
16
17
18
19
20
1
2
3
4
5
POWER (STANDBY/ON)
To switch the power on and off. (See page 14.)
0–9
Set the channel. (See page 19.)
TELETEXT mode: Set the page. (See pages 51 and 52.)
A (Flashback)
Press to return to the previous selected channel or
external input mode. (See page 25.)
IN 3 (HDMI)
Directly select the INPUT 3 terminal. (See page 37.)
IN 4 (HDMI)
Directly select the INPUT 4 terminal. (See page 37.)
21
22
23
24
MPX
Select the sound multiplex mode. (See page 26.)
VOLk/VOLl
Set the volume. (See page 19.)
e (Mute)
Mute the sound. (See page 25.)
WIDE
Change the wide image mode. (See pages 31 and 46.)
FREEZE
Freeze a motion picture on the screen. (See page 24.)
EXIT
Return to the default screen.
AQUOS LINK buttons
If external equipment such as a AQUOS BD Player
is connected via HDMI cables and is AQUOS LINK
compatible, you can use these AQUOS LINK buttons.
See pages 40 to 44 for details.
m (TELETEXT)
Select the TELETEXT mode. (all TV image, all TEXT
image, TV/TEXT image) (See pages 51 and 52.)
k (Reveal hidden for TELETEXT)
TELETEXT mode: Display hidden characters. (See page
51.)
[ (SUBTITLE for TELETEXT)
To turn the subtitles on and off. (See page 52.)
3 (Hold)
TELETEXT mode: Stop updating Teletext pages
automatically. Press 3 again to release the hold mode.
(See pages 51 and 52.)
1 (Subpage)
Display the Teletext subpage directly. (See page 52.)
v (Top/Bottom/Full)
TELETEXT mode: Set the area of magnification. (See
page 51.)
TV/VIDEO (INPUT SOURCE)
Select an input source. (TV, INPUT 1, INPUT 2, INPUT 3,
INPUT 4, INPUT 5 (PC)) (See pages 11, 37 to 39, 45.)
OPC
To switch the Optical Picture Control on and off. (See
page 33.)
AV MODE
Select an audio and video setting: AV MODE (STANDARD,
MOVIE, GAME, USER, DYNAMIC (FIXED), DYNAMIC), PC
MODE (STANDARD, PC, USER). (See page 32.)
DISPLAY
Display the channel or input information.
CHr/CHs
TV input mode: Select the channel. (See page 19.)
TELETEXT mode: Select the page. (See page 51.)
SLEEP
Set the Sleep timer. (See page 28.)
PC
Directly select the INPUT 5 terminal. (See page 45.)
MENU
Display the menu screen. (See page 15.)
a/b/c/d (Cursor)
Select a desired item on the setting screen.
ENTER
Execute a command.
RETURN
MENU mode: Return to the previous menu screen. (See
page 15.)
Colour (Red/Green/Yellow/Blue)
TELETEXT mode: Select a page. (See page 51.)
9
32A33X_en_b.indd 9
2008-1-4 20:13:36
Preparation
Before turning on the power
Notes on installing the TV
• Avoid direct sunlight and place the TV in a well-ventilated location.
• Place the TV in a level location.
• Do not turn on the power of the TV before connecting the AC cord.
1
Connecting the antenna cable
To enjoy a clearer picture, use an outdoor antenna. The following is a brief explanation of the types of
connections that are used for coaxial cable.
Standard DIN45325 plug (IEC169-2)
75-ohm coaxial cable (round cable)
Antenna cable
(commercially available)
Room antenna terminal
(75-ohm type)
To antenna
terminal
2
Connecting external devices
See pages 10 to 12 for connecting antennas and external equipment, such as a VCR and DVD player.
3
Connecting the AC cord
TV (rear view)
AC outlet
AC cord
• Place the TV close to the AC outlet, and keep the power plug within reach.
• Disconnect the AC cord from the AC outlet if the TV will not be used for a long period of time.
4
Bundling the cables
Insert the cable clamp in the hole on the TV as shown.
Cable clamp
CAUTION
• TO PREVENT RISK OF ELECTRIC SHOCK, DO NOT TOUCH UN-INSULATED PARTS OF ANY CABLES WITH THE
AC CORD CONNECTED.
10
32A33X_en_b.indd 10
2008-1-4 20:13:36
Preparation
Connecting external devices
You can connect many types of external equipment to your TV, like a VCR, game console, camcorder, DVD
player, Digital TV STB (Set Top Box) and PC. To view external source images, select the input source from TV/
VIDEO on the remote control unit or TV/VIDEO on the TV.
CAUTION
• To protect all equipment, always turn off the TV before connecting to a VCR, game console, camcorder, DVD player, Digital
TV STB (Set Top Box), PC or other external equipment.
• Refer to the relevant operation manual (VCR, DVD player, etc.) carefully before making connections.
Connecting a VCR, game console or camcorder
A VCR, game console, camcorder and some other audiovisual equipment can be conveniently connected using
the INPUT 1/INPUT 2 terminals.
When using component cable
(commercially available)
Y
When using composite cable or
S-VIDEO cable (commercially available)
S-VIDEO
PB
(CB)
PR
(CR)
or
R
AUDIO
L
R
AUDIO
L
VCR/
Game console/
Camcorder
VIDEO
VCR/
Game console/
Camcorder
Connecting a DVD player
You can use the INPUT 1/INPUT 2, INPUT 3/INPUT 4 (HDMI) terminals when connecting to a DVD player and
other audiovisual equipment.
NOTE
• When using a DVI-HDMI conversion adaptor, input the Audio Signal from the AUDIO terminal of INPUT 3. (See page 37.)
When using HDMI-certified cable
(commercially available)
When using component cable
(commercially available)
Y
PB
(CB)
PR
(CR)
DVD player
R
AUDIO
L
DVD player
11
32A33X_en_b.indd 11
2008-1-4 20:13:37
Preparation
Connecting a Digital TV STB (Set Top Box)
You can use the INPUT 1/INPUT 2 or INPUT 3/INPUT 4 (HDMI) terminals when connecting to a Digital TV STB (Set
Top Box) and other audiovisual equipment.
NOTE
• When using a DVI-HDMI conversion adaptor, input the Audio Signal from the AUDIO terminal of INPUT 3. (See page 37.)
When using HDMI-certified cable
(commercially available)
When using component cable
(commercially available)
Y
PB
(CB)
PR
(CR)
Digital TV
STB
(Set Top Box)
R
AUDIO
L
Digital TV STB
(Set Top Box)
Connecting a PC
You can use the INPUT 5 (PC) terminal when connecting
to a PC. (See page 45.)
ANALOG
RGB
AUDIO
(L/R)
PC
12
32A33X_en_b.indd 12
2008-1-4 20:13:37
Preparation
Inserting the batteries
Before using the TV for the first time, insert two “AAA” size batteries (supplied). When the batteries become
depleted and the remote control fails to operate, replace the batteries with new “AAA” size batteries.
1 Open the battery cover.
2 Insert the two supplied “AAA” size 3 Close the battery cover.
batteries.
• Place batteries with their terminals
corresponding to the (e) and (f)
indications in the battery compartment.
CAUTION
Improper use of batteries can result in chemical leakage or explosion. Be sure to follow the instructions below.
• Do not mix batteries of different types. Different types of batteries have different characteristics.
• Do not mix old and new batteries. Mixing old and new batteries can shorten the life of new batteries or cause chemical
leakage in old batteries.
• Remove batteries as soon as they have worn out. Chemicals that leak from batteries can cause a rash. If you find any
chemical leakage, wipe thoroughly with a cloth.
• The batteries supplied with this product may have a shorter life expectancy due to storage conditions.
• If you will not be using the remote control unit for an extended period of time, remove the batteries from it.
Using the remote control unit
Use the remote control unit by pointing it towards the
remote sensor window.
Objects between the remote control unit and sensor
window may prevent proper operation.
30º
5m
30º
30º
Remote control sensor
30º
Cautions regarding the remote control unit
• Do not subject the remote control unit to shock.
In addition, do not soak the remote control unit with liquids or place it in
an area with high humidity.
• Do not install or place the remote control unit under direct sunlight.
The heat may cause deformation of the unit.
• The remote control unit may not work properly if the remote sensor
window of the TV is under direct sunlight or strong lighting. In such
cases, change the angle of the lighting or TV, or operate the remote
control unit closer to the remote sensor window.
13
32A33X_en_b.indd 13
2008-1-4 20:13:37
Preparation
Turning the TV on/off
Turning on the power
Turning off the power
Press POWER on the TV.
POWER button
• POWER indicator (Green): The TV is on. (After a few
seconds, an image appears with sound.)
• After turning the power “ON” by pressing POWER on the
TV, you can turn the power ON/OFF by pressing POWER
on the remote control.
POWER button
Press POWER on the remote control.
• The TV enters standby mode and the image on the screen
disappears.
• The POWER indicator on the TV changes from green to
red.
Press POWER on the TV.
• The POWER indicator on the TV turns off.
• When the TV is turned off by POWER on the TV, you
cannot turn on the power by pressing POWER on the
remote control.
POWER indicator
POWER indicator
Light off
Power off
Lighted (Red)
The TV is in standby mode.
Lighted (Green)
The TV is on.
NOTE
• If you are not going to use this TV for a long period of time,
be sure to remove the AC cord from the AC outlet.
• Minor power is consumed when the unit is in standby
mode.
14
32A33X_en_c.indd 14
2008-1-4 20:14:07
Preparation
About Menu operations
H Using the control panel of the TV
What is Menu?
• You need to bring up the On-Screen Display to perform
settings for the TV. The On-Screen Display for the settings
is called “Menu”.
• The Menu enables various settings and adjustments. (See
pages 16 and 17.)
• The Menu can be operated with the remote control unit.
You can also operate the Menu using the control panel
of the TV.
Button operations on the control panel correspond to
the ones on the remote control as shown below.
Basic Menu operations
1
Remote control buttons
TV/VIDEO
ENTER
CH r
a
CH s
b
VOL k
d
VOL l
c
Press MENU and the MENU screen displays.
MENU
[Picture]
Picture
AV Mode
Audio
Power Control
[STANDARD]
OPC
[Off]
Backlight
[+16]
Contrast
[ 30]
+
Brightness [
0]
+
Colour
[
0]
+
Tint
[
0]
Sharpness [
0]
+
Advanced
Reset
2
TV control panel buttons
Press c/d to select the desired menu, and
then press ENTER.
Audio
NOTE
• Menu options differ in the selected input modes, but the
operating procedures are the same.
• The screens in the operation manual are for explanation
purposes (some are enlarged, others cropped) and may
vary slightly from the actual screens.
About Guide Display
Power Control
STANDARD
Treble
[ 0]
-
+
Bass
[ 0]
-
+
Balance
[ 0]
L
R
The Guide Display at the bottom of the screen shows
operations with an On-Screen Display.
Surround
: Select
Reset
3
Press a/b to select the desired menu item.
Press ENTER to proceed if necessary.
Audio
Power Control
ENTER
: Enter
RETURN
: Back
MENU
: End
The bar above is an operational guide for
the remote control. The bar will change in
accordance with each menu setting screen.
STANDARD
Treble
[ 0]
-
+
Bass
[ 0]
-
+
Balance
[ 0]
L
R
Surround
Reset
4
5
Press a/b or c/d to select the desired item
or adjust the item to the desired level. Press
ENTER if necessary.
Press EXIT or MENU to exit the MENU.
Press RETURN as necessary to return to the
previous MENUs.
15
32A33X_en_c.indd 15
2008-1-4 20:14:08
Preparation
TV/AV input mode menu items
List of TV/AV menu items to help you with operations
Picture
AV Mode ..................................................................... Page 32
OPC ............................................................................. Page 33
Backlight .................................................................... Page 33
Contrast ...................................................................... Page 33
Brightness .................................................................. Page 33
Colour ......................................................................... Page 33
Tint .............................................................................. Page 33
Sharpness .................................................................. Page 33
Advanced
Colour Temp. .................................................. Page 34
Film Mode ....................................................... Page 34
Black ............................................................... Page 34
3D-Y/C ............................................................ Page 34
Monochrome .................................................. Page 34
Reset ........................................................................... Page 33
Setup
Auto Installation ......................................................... Page 18
Programme Setup .............................................. Pages 20-23
Child Lock .................................................................. Page 27
Input Skip ................................................................... Page 39
Input Label ................................................................. Page 39
Position ....................................................................... Page 35
WSS ............................................................................ Page 30
4:3 Mode ..................................................................... Page 30
Standby Mode ............................................................ Page 26
Language .................................................................... Page 19
Text Language ........................................................... Page 53
Reset ........................................................................... Page 56
Option
Audio
AV Mode ..................................................................... Page 32
Treble .......................................................................... Page 36
Bass ............................................................................ Page 36
Balance ....................................................................... Page 36
Surround ..................................................................... Page 36
Reset ........................................................................... Page 36
Power Control
AQUOS LINK Setup .................................................... Page 41
DNR ............................................................................. Page 35
Input Select
INPUT1 ............................................................ Page 38
INPUT2 ............................................................ Page 38
Output Volume Select ............................................... Page 36
Audio Only .................................................................. Page 25
Game Play Time ......................................................... Page 35
Colour System ........................................................... Page 39
HDMI Setup
Auto View ........................................................ Page 37
Audio Select ................................................... Page 37
No Signal Off .............................................................. Page 28
No Operation Off ....................................................... Page 28
Ecology ....................................................................... Page 29
NOTE
• Some menu items may not be displayed depending on the selected input source.
16
32A33X_en_c.indd 16
2008-1-31 12:59:49
Preparation
PC input mode menu items
List of PC menu items to help you with operations
Picture
AV Mode ..................................................................... Page 32
OPC ............................................................................. Page 33
Backlight .................................................................... Page 33
Contrast ...................................................................... Page 33
Brightness .................................................................. Page 33
Advanced
Colour Temp. .................................................. Page 34
Black ............................................................... Page 34
Reset ........................................................................... Page 33
Setup
Input Skip ................................................................... Page 39
Input Label ................................................................. Page 39
Standby Mode ............................................................ Page 26
Language .................................................................... Page 19
Text Language ........................................................... Page 53
Reset ........................................................................... Page 56
Option
Audio
AV Mode ..................................................................... Page 32
Treble .......................................................................... Page 36
Bass ............................................................................ Page 36
Balance ....................................................................... Page 36
Surround ..................................................................... Page 36
Reset ........................................................................... Page 36
Power Control
Power Management .................................................. Page 29
No Operation Off ....................................................... Page 28
Ecology ....................................................................... Page 29
AQUOS LINK Setup .................................................... Page 41
Input Select
INPUT1 ............................................................ Page 38
INPUT2 ............................................................ Page 38
Output Volume Select ............................................... Page 36
Audio Only .................................................................. Page 25
Game Play Time ......................................................... Page 35
Fine Sync.
Input Signal ..................................................... Page 48
Auto Sync. ...................................................... Page 47
H-Position ....................................................... Page 47
V-Position ....................................................... Page 47
Clock ............................................................... Page 47
Phase .............................................................. Page 47
Reset ............................................................... Page 47
NOTE
• Some menu items may not be displayed depending on the selected input source.
17
32A33X_en_c.indd 17
2008-1-31 12:59:50
Watching TV
Setting channels automatically
You can run auto installation again, even after setting
up the preset channels.
4
If you have already set the password, enter it
here.
• See page 27 for setting a password.
1
Press MENU and the MENU screen displays.
2
Press c/d to select “Setup”.
3
5
Press a/b to select “Yes”, and then press
ENTER.
6
Press a/b to select the desired language
listed on the screen, and then press ENTER.
Press a/b to select the desired sound
system, and then press ENTER.
You do not need to do anything during the
auto search.
“Search is completed.” is displayed. Press
MENU to exit.
Press a/b to select “Auto Installation”, and
then press ENTER.
MENU
[Setup ... Auto Installation]
Setup
Option
Auto Installation
Programme Setup
Child Lock
Input Skip
Input Label
Position
WSS
4:3 Mode
Standby Mode
Language
Text Language
Reset
18
32A33X_en_c.indd 18
2008-1-4 20:14:09
Watching TV
Selecting programmes
Adjusting the volume
You can change channels in several ways.
Using CHr/s on the remote control unit
• Press CHr to increase the channel number.
• Press CHs to decrease the channel number.
NOTE
• CHr/s on the TV operates the same as CHr/s on
the remote control unit.
Changing the volume
You can change the volume on the TV or on the
remote control unit.
• To increase the volume, press VOLk.
• To decrease the volume, press VOLl.
20
Using 0 — 9 on the remote control unit
Select the channels directly by pressing buttons 0 to 9.
NOTE
• “TV”, “INPUT1”, “INPUT2”, “INPUT3”, “INPUT4” and
“INPUT5” (PC) modes can store volume adjustment values
separately.
Menu language settings
a
To select a 1-digit channel (e.g. channel 2):
• Press 0, followed by 2.
To select a 2-digit channel (e.g. channel 12):
• Press 1, followed by 2.
When viewing Teletext information
View a page directly which is 3-digit page number from
100 to 899 by pressing buttons 0 to 9.
You can also select a language from setup menu.
Select from among 4 languages: English, Simplified
Chinese, Traditional Chinese and Arabic.
1
Press MENU and the MENU screen displays.
2
Press c/d to select “Setup”.
3
Press a/b to select “Language”, and then
press ENTER.
4
Press a/b to select the desired language
listed on the screen, and then press ENTER.
Channel display
(Example)
PAL
SAT.1
12
B/G
MONO
19
32A33X_en_c.indd 19
2008-1-4 20:14:09
Watching TV
Setting channels to your preference
You can run the auto search procedure again at any
time by accessing the Setup menu and Programme
Setup. Channels can be tuned automatically or
manually.
Auto search
Manual setting for each channel
You can also automatically search by performing
the procedure below. This is the same function as
programme auto search in auto installation.
1
2
3
Press MENU and the MENU screen displays.
Press c/d to select “Setup”.
Press a/b to select “Programme Setup”, and
then press ENTER.
If you have already set the password, enter it
here.
You can set some channel items manually. They are
Search, Fine (TV frequency), Colour System, Sound
System and Skip.
1
2
3
[Setup ... Programme Setup]
Setup
Option
Press a/b to select “Programme Setup”, and
then press ENTER.
If you have already set the password, enter it
here.
4
Press a/b to select “Manual Adjust”, and
then press ENTER.
5
Press a/b to select “Yes”, and then press
ENTER.
Auto Installation
Programme Setup
Press c/d to select “Setup”.
• See page 27 for setting a password.
• See page 27 for setting a password.
MENU
Press MENU and the MENU screen displays.
Child Lock
Input Skip
Programme Setup “Manual Adjust” menu
Input Label
Position
01 SAT.1
02 PR07
03 KABEL
WSS
4:3 Mode
Standby Mode
Language
Text Language
Reset
4
5
Press a/b to select “Auto Search”, and then
press ENTER.
Press a/b to select “Yes”, and then press
ENTER.
Press a/b to select the desired sound
system, and then press ENTER.
“Search is completed.” is displayed. Press
MENU to exit.
You can select one of the following settings.
1
2
3
4
5
Search (See page 21.)
Fine (See page 21.)
Colour system (See page 21.)
Sound system (See page 21.)
Skip (See page 22.)
20
32A33X_en_c.indd 20
2008-1-4 20:14:09
Watching TV
Manual setting for each channel (continued)
Search tuning
1
Colour system
Press a/b/c/d to select the channel you
want to edit, and then press ENTER.
1
• The selected channel information displays.
• The selected channel information displays.
2
Press a/b to select “Search”, and then press
ENTER.
MENU
2
Colour system menu
Channel Search.
Fine
Colour System
Search
179.25 MHz
Select desired item
Fine
Sound System
Skip
Press a/b to select “Colour System” and
then press ENTER.
• Receivable colour systems are listed.
[Setup ... Programme Setup]
Search
Press a/b/c/d to select the channel you
want to edit, and then press ENTER.
NEXT
Colour System
AUTO
Sound System
PAL
Skip
SECAM
NTSC 3. 58
NTSC 4. 43
3
As ENTER is pressed, the next channels will
be searched in order.
PAL-60
3
Fine tuning
1
Press a/b/c/d to select the channel you
want to edit, and then press ENTER.
• The selected channel information displays.
2
Press a/b to select “Fine”, and then press
ENTER.
3
Press c/d to adjust the frequency, and then
press RETURN or MENU.
Sound system (Broadcasting system)
1
Press a/b/c/d to select the channel you
want to edit, and then press ENTER.
• The selected channel information displays.
2
Press a/b to select “Sound System”, and
then press ENTER.
• Receivable sound systems (Broadcasting systems)
are listed.
Sound system menu
• Adjust while checking the background picture as
a reference.
Search
Press a/b to select the optimum colour
system, and then press ENTER.
Search
Set value at desired level
Select desired item
Fine
Fine
Colour System
B/G
Sound System
Sound System
D/K
Skip
Skip
I
Colour System
179.25 MHz
M
• Instead of the method above, you can also set
by directly entering the frequency number of the
channel with 0 — 9.
• When setting a frequency on the “Fine” screen,
the last figure of the frequency needs to be “0” or
“5”.
a
• 179.25 MHz: Press 1 s 7 s 9 s 2 s 5.
• 49.25 MHz: Press 4 s 9 s 2 s 5 s ENTER.
3
Press a/b to select the optimum sound
system, and then press ENTER.
NOTE
• Check the sound system if the sound output were not
correct.
21
32A33X_en_c.indd 21
2008-1-4 20:14:10
Watching TV
Manual setting for each channel (continued)
Skipping channels
Channels with “Skip” set to “On” are passed over
when using CHr/s even if selected while watching
the image from the TV.
1
Press a/b/c/d to select the channel you
want to edit, and then press ENTER.
• The selected channel information will be displayed.
2
Sorting programmes
Channel positions can be sorted freely.
1
Press MENU and the MENU screen displays.
2
Press c/d to select “Setup”.
3
Press a/b to select “Programme Setup”, and
then press ENTER.
If you already set the password, enter it here.
Press a/b to select “Skip”, and then press
ENTER.
• See page 27 for setting a password.
• Skip menu displays.
Skip menu
MENU
[Setup ... Programme Setup]
Search
Select desired item
Fine
Colour System
4
Press a/b to select “Sort”, and then press
ENTER.
5
Press a/b to select “Yes”, and then press
ENTER.
6
Press a/b/c/d to select the channel you
want to move, and then press ENTER.
7
Move it to the desired position by pressing
a/b/c/d, and then press ENTER.
8
Repeat the steps 6 and 7 until all desired
channels are sorted.
Off
Sound System
Skip
3
On
Press a/b to set “Skip” to “On”, and then
press ENTER.
Sort menus
01 SAT.1
01 SAT.1
02 KABEL
03
04
05
06
07
08
09
10
11
12
13
14
15
16
17
18
19
20
01 SAT.1
02 KABEL
01 SAT.1
02 KABEL
03
04
06
07
08
09
10
11
12
13
14
15
16
17
18
19
20
05
01 KABEL
01 KABEL
02 SAT.1
03
04
05
06
07
08
09
10
11
12
13
14
15
16
17
18
19
20
22
32A33X_en_c.indd 22
2008-1-4 20:14:10
Watching TV
Erasing programmes
Labelling programmes
The individual programme can be erased.
Channels can be labelled freely.
1
Press MENU and the MENU screen displays.
1
Press MENU and the MENU screen displays.
2
Press c/d to select “Setup”.
2
Press c/d to select “Setup”.
3
Press a/b to select “Programme Setup”, and
then press ENTER.
If you already set the password, enter it here.
3
Press a/b to select “Programme Setup”, and
then press ENTER.
If you already set the password, enter it here.
• See page 27 for setting a password.
4
Press a/b to select “Erase Programme”, and
then press ENTER.
5
Press a/b to select “Yes”, and then press
ENTER.
• See page 27 for setting a password.
4
Press a/b to select “Label”, and then press
ENTER.
MENU
[Setup ... Programme Setup]
Auto Search
Label Settings.
Manual Adjust
6
7
8
Sort
Press a/b/c/d to select the channel you
want to erase, and then press ENTER.
Erase Programme
Press ENTER to erase the channel.
All the subsequent programmes move up.
Repeat the steps 6 and 7 until all desired
channels are erased.
Erase programme menus
01 SAT.1
02 PRO7
03 KABEL
04
05
06
07
08
09
10
11
12
13
14
15
16
17
18
19
20
01 SAT.1
02 PRO7
03 KABEL
04
05
06
07
08
09
10
11
12
13
14
15
16
17
18
19
20
01 SAT.1
02 KABEL
03
04
05
06
07
08
09
10
11
12
13
14
15
16
17
18
19
20
Yes
Label
No
5
Press a/b to select “Yes”, and then press
ENTER.
6
Press a/b/c/d to select the channel you
want to label, and then press ENTER.
7
Press a/b to select characters and c/d
to move to the desired digit, and then press
ENTER to complete the label setting.
23
32A33X_en_c.indd 23
2008-1-4 20:14:10
Watching TV
Useful viewing functions
Split-screen viewing
This function is conveniently used when, for instance,
watching cooking programmes and taking notes.
Picture and still image
You can freeze a motion picture on the Display.
1
Press FREEZE.
• A moving image displays on the left screen and
a still image displays on the right screen. The still
image is one frame captured from a moving image
at the moment you press FREEZE.
FREEZE
(Example)
2
Reshoot the still image by pressing ENTER.
3
Press RETURN to exit still image.
• Each time you press ENTER, the image on the
right screen updates.
NOTE
• The still image automatically goes out after 30 minutes.
24
32A33X_en_c.indd 24
2008-1-4 20:14:11
Watching TV
Returning to the previously selected
channel
Outputting only audio
When listening to music from a music programme, you
can set the display off and enjoy audio only.
1
Press MENU and the MENU screen displays.
2
Press c/d to select “Option”.
Press A to switch the currently tuned channel to the
previously tuned channel.
Press A again to switch back to the currently tuned
channel.
3
Press a/b to select “Audio Only”, and then
press ENTER.
Press A to toggle between the currently selected
input source and the previously selected one.
4
Press a/b to select “On”, and then press
ENTER.
Press A to return to the previous page in TELETEXT
mode.
Muting the audio temporarily
Using Mute (e) on the remote control unit
e mutes the current sound output.
1
Press e.
Selected item
Description
On
Audio is output without screen image.
Off
Both screen images and audio are output.
NOTE
• When you make operations that change the picture on the
TV such as by changing the input source, the Audio Only
function is set to “Off”.
• The sound is silenced.
• “M” is displayed while the mute function is on.
Mute
2
Press e again within 30 minutes to cancel the
mute.
• Before 30 minutes, the volume level returns to the
previous setting.
NOTE
• Mute will be cancelled after 30 minutes. However,
the TV will not suddenly output loud sound as the
volume level will be set to 0 automatically. Increase
the volume level by pressing VOLk.
25
32A33X_en_d.indd 25
2008-1-4 20:14:38
Watching TV
Switching the analogue audio format
You can switch between multiple audio modes
when watching a multiple audio or stereo broadcast
programme.
When receiving a bilingual signal
Each time you press MPX, the mode switches among
CH A, CH B and CH AB.
Bilingual mode
BBC2
99
PAL
In the NICAM TV broadcasts
When receiving a stereo signal
Each time you press MPX, the mode switches
between NICAM STEREO and MONO.
BBC2
99
B/G
CH A
PAL
B/G
CH B
BBC2
99
PAL
B/G
CH AB
Stereo mode
BBC2
99
BBC2
99
PAL
NICAM
B/G
STEREO
PAL
When receiving a monaural signal
When you press MPX, “MONO” displays.
B/G
MONO
Monaural mode
BBC2
99
PAL
When receiving a bilingual signal
Each time you press MPX, the mode switches among
NICAM CH A, NICAM CH B, NICAM CH AB and
MONO.
B/G
MONO
NOTE
• “BBC2” and “99” are tentative network name and channel.
Bilingual mode
BBC2
99
PAL
NICAM
B/G
CH A
BBC2
99
PAL
NICAM
BBC2
99
PAL
B/G
MONO
B/G
CH B
BBC2
99
PAL
NICAM
B/G
CH AB
When receiving a monaural signal
Each time you press MPX, the mode switches
between NICAM MONO and MONO.
Reducing the start-up time
You can reduce the TV’s start-up time after the turning
on the power with the remote control unit.
1
Press MENU and the MENU screen displays.
2
Press c/d to select “Setup”.
3
Press a/b to select “Standby Mode”, and
then press ENTER.
4
Press a/b to select “Mode 1” or “Mode 2”,
and then press ENTER.
Monaural mode
BBC2
99
PAL
NICAM
B/G
MONO
BBC2
99
PAL
B/G
MONO
Selected item
In the TV mode of A2 TV broadcasts
When receiving a stereo signal
Each time you press MPX, the mode switches
between STEREO and MONO.
BBC2
99
PAL
B/G
STEREO
Mode 1
Starting the TV is quick from standby.
Mode 2
Power consumption is small during
standby.
5
Stereo mode
Description
Press MENU to exit.
BBC2
99
PAL
B/G
MONO
26
32A33X_en_d.indd 26
2008-1-4 20:14:39
Watching TV
Password setting for the child lock
(for TV input mode)
Allows you to use a password to protect certain
settings from being accidentally changed.
Setting a channel
1
Repeat steps 1 to 4 in Setting a password.
2
Press a/b to select “Channel Setting”, and
then press ENTER.
3
Press a/b to select “Yes”, and then press
ENTER.
Press MENU and the MENU screen displays.
2
Press c/d to select “Setup”.
3
Press a/b to select “Child Lock”, and then
press ENTER.
4
If you already set the password, enter it here.
5
Press a/b to select “Change Password”, and
then press ENTER.
Change Password
Enter your new password.
Channel Setting
Use 4 digits.
Reset
New Password
Select child lock
Channel Setting
Channels.
Reset
Setting a password
Register a 4-digit password number to use the Child
Lock function.
1
Change Password
Yes
No
4
Press a/b/c/d to select the channel that
you wish to apply the Child Lock, and then
press ENTER.
Resetting the password
Allows you to reset your password.
1
Repeat steps 1 to 4 in Setting a password.
2
Press a/b to select “Reset”, and then press
ENTER.
3
Press a/b to select “Yes”, and then press
ENTER.
Change Password
Clear password.
Reconfirm
Channel Setting
Reset
Yes
6
Enter the 4-digit number as a password using
0 — 9.
Change Password
Enter your new password.
Channel Setting
Use 4 digits.
Reset
New Password
Reconfirm
7
Enter the same 4-digit number as in step 6 to
confirm.
No
NOTE
• As a precautionary measure, make a note of your
password on the back of this operation manual, cut
it out and keep it in a safe place that children cannot
reach.
• This function is only available for TV input mode.
• To relock a channel which has been temporarily unlocked
by inputting the correct password, turn power off and then
on again.
NOTE
• To view a locked channel you must enter a password.
When you select a locked channel, a password prompt
message pops up.
• Press ENTER to display the password input window.
27
32A33X_en_d.indd 27
2008-1-10 8:29:04
Watching TV
Energy conservation settings
Auto power-off at a designated time
This function is conveniently used when, for instance,
going to bed while watching TV.
1
Press SLEEP.
• Remaining time displays when sleep timer has
been set.
Auto power-off after the end of broadcast
You can set the TV to automatically power off in about
15 minutes after the TV goes into a state of receiving
no programme signals, such as the end of a broadcast
day.
1
Press MENU and the MENU screen displays.
2
Press c/d to select “Power Control”.
3
Press a/b to select “No Signal Off”, and then
press ENTER.
4
Press a/b to select “Enable”.
Sleep timer: Remain 2hr. 00min.
2
Each time you press SLEEP, the remaining
time switches as shown below.
0hr. 30min.
Off
1hr. 00min.
2hr. 30min.
1hr. 30min.
2hr. 00min.
NOTE
• When the time has been set, countdown automatically
starts.
• Five minutes before the preset of time expires, the
remaining time displays each minute.
• Select “Off” by pressing SLEEP to cancel the sleep timer.
• Five minutes before the power shuts down, the
remaining time displays every minute.
NOTE
• “Disable” is the factory preset value.
• When a TV programme finishes, and the TV receives signal
input, this function may not operate.
Auto power-off when there are no
operations performed
You can set the TV to automatically power off when no
TV operation is performed for more than 3 hours.
1
Press MENU and the MENU screen displays.
2
Press c/d to select “Power Control”.
3
Press a/b to select “No Operation Off”, and
then press ENTER.
4
Press a/b to select “30 min” or “3 hour”.
• Five minutes before the power shuts down, the
remaining time displays every minute.
NOTE
• “Disable” is the factory preset value.
28
32A33X_en_d.indd 28
2008-1-4 20:14:40
Watching TV
Power Management
Ecology
You can set the TV to automatically power off when no
image is displayed on PC.
1
2
3
4
Press MENU and the MENU screen displays.
Press c/d to select “Power Control”.
Press a/b to select “Power Management”,
and then press ENTER.
Press a/b to select “Mode1” or “Mode2”,
and then press ENTER.
Select desired item
When set to “Yes”, The TV activates the following
power saving mode.
•
•
•
•
•
“OPC” set to “On” (Page 33)
“Standby Mode” set to “Mode 2” (Page 26)
“No Signal Off” set to “Enable” (Page 28)
“No Operation Off” set to “3 hour” (Page 28)
“Power Management” set to “Mode 1” (Page 29)
1
Press MENU and the MENU screen displays.
2
Press c/d to select “Power Control”.
3
Press a/b to select “Ecology”, and then
press ENTER.
4
Press a/b to select “Yes”, and then press
ENTER.
Off
Mode 1
Mode 2
NOTE
• Ecology mode cannot be deactivated by selecting “No”.
Each setting must be changed individually to deactivate
Ecology mode.
Selected item
Description
Off
• No power management
• Factory preset value.
Mode 1
• If no signal inputs for approximately 8
minutes, the power shuts down.
• Even if you start using the PC and the
signal inputs again, the TV stays off.
• The TV turns on again by pressing
POWER. (See page 14.)
Mode 2
• If no signal inputs for approximately 8
seconds, the power shuts down.
• When you start using the PC and the
signal inputs again, the TV turns on.
• The TV turns on again by pressing
POWER. (See page 14.)
NOTE
• If you turn off the power by disconnecting AC cord when
setting “Mode 2” in power management, the TV may not
function properly after turning the power on again. In such
case, press POWER on the remote control unit.
• Pressing POWER on the display will have the same result.
29
32A33X_en_d.indd 29
2008-1-10 8:29:05
Watching TV
Picture size settings
Selecting the Wide Screen Signalling
(WSS) picture size automatically
WSS allows a television to switch automatically among
the different screen formats.
Selecting the Wide Screen Signalling
(WSS) picture size manually
The WSS signal has 4:3 auto-switching that allows you
to select between Panorama and Normal.
1
Press MENU and the MENU screen displays.
1
Press MENU and the MENU screen displays.
2
Press c/d to select “Setup”.
2
Press c/d to select “Setup”.
3
Press a/b to select “WSS”, and then press
ENTER.
3
Press a/b to select “4:3 Mode”, and then
press ENTER.
4
Press a/b to select “On” or “Off”, and then
press ENTER.
4
Press a/b to select “Panorama” or “Normal”,
and then press ENTER.
NOTE
• Try to set WIDE mode if an image does not switch to the
correct screen format. When the broadcast signal contains
no WSS information, the function will not work even if
enabled.
WSS signal 4:3 screen
4:3 mode “Panorama”
Selected item
4:3 mode “Normal”
Description
Panorama
Wide image without side bars
Normal
Normal range keeping 4:3 or 16:9 aspect
ratio
30
32A33X_en_d.indd 30
2008-1-4 20:14:40
Watching TV
Selecting the picture size manually
Manual Selection
You can select different picture sizes that account for
the kind of each picture.
Auto Selection
If you set “WSS” and “4:3 Mode” in the Setup menu
on page 30, the optimum WIDE mode is automatically
chosen for every broadcast containing the WSS
information.
“WSS” menu
To enable Auto Selection, set “WSS” in the Setup
menu to “On”. (See page 30.)
“4:3 Mode” menu
To set the type of the wide screen, select “Panorama”
or “Normal” in the 4:3 Mode menu. (See page 30.)
Press WIDE.
1
• The WIDE MODE menu displays.
• The menu lists the wide mode options selectable
for the type of video signal currently received.
WIDE MODE
Normal
Zoom 14:9
4:3 Mode set to “Panorama”
Panorama
Full
Cinema 16:9
4:3 Mode set to “Normal”
NOTE
• If the broadcast signal contains no WSS information, Auto
Selection will not function even when the WSS option is
enabled.
Cinema 14:9
Press WIDE or a/b while the WIDE MODE
menu displays on the screen.
2
• As you toggle down the options, each mode is
immediately reflected on the TV.
Selected item
Description
Normal
For 4:3 “standard” pictures. A side bar appears on each side.
Zoom 14:9
For 14:9 letterbox pictures. A thin side bar appears on each side, and you may also see bars on the top and
bottom with some programmes.
Panorama
In this mode the picture is progressively stretched toward each side of the screen.
Full
For 16:9 squeeze pictures.
Cinema 16:9
For 16:9 letterbox pictures. Bars may appear on the top and bottom with some programmes.
Cinema 14:9
For 14:9 letterbox pictures. Bars may appear on the top and bottom with some programmes.
Underscan
Display with an Underscan image only when receiving a 720p signal. Display with the High-Definition image
adjusted optimally. Noise may appear on the edge of the screen with some programs.
Normal
Zoom 14:9
Panorama
Cinema 14:9
Cinema 16:9
Full
NOTE
• Some picture sizes may not be
displayable depending on the
input signal.
31
32A33X_en_d.indd 31
2008-1-4 20:14:40
Watching TV
Selecting a preset AV MODE
The AV MODE function enables you to select
appropriate settings for audio and video to account for
the system environment which can vary due to factors
like room brightness, type of programme watched or
the type of image input from external equipment.
Using AV MODE on the remote control unit
1
Press AV MODE.
2
Press AV MODE again before the mode
displayed on the screen disappears.
• Present AV MODE displays.
• The mode changes as shown below.
AV input mode
AV Mode : STANDARD
AV Mode : MOVIE
AV Mode : DYNAMIC
AV Mode : GAME
AV Mode : DYNAMIC (FIXED)
AV Mode : PC
Selected item
Description
STANDARD
For a highly defined image in a normally
bright room
MOVIE
For a movie
GAME
Lowers image brightness for easier
viewing.
PC
For PC. (Available only when inputting an
HDMI or PC signal.)
USER
Allows the user to customise settings as
desired. You can set the mode for each
input source.
DYNAMIC
(FIXED)
Changes the image and sound settings to
the factory preset values. No adjustments
are allowed.
DYNAMIC
For a clear-cut image emphasising high
contrast for sports viewing.
NOTE
• You can select a different AV MODE item for each input
mode. (For example, select STANDARD for TV input and
DYNAMIC for VIDEO input.)
• During PC input mode, only “STANDARD”, “PC” and
“USER” can be selected under the AV mode selection.
AV Mode : USER (TV)
PC input mode
AV Mode : PC
AV Mode : STANDARD
AV Mode : USER (
)
Using AV Mode on the menu screen
1
Press MENU and the MENU screen displays.
2
Press c/d to select “Picture”.
3
Press a/b to select “AV Mode”, and then
press ENTER.
4
Press a/b to select the desired item, and
then press ENTER.
32
32A33X_en_e.indd 32
2008-1-4 20:15:18
Watching TV
Manual picture settings
Selected item
Picture adjustment
2
Press MENU and the MENU screen displays.
Press c/d to select “Picture”.
MENU
dbutton
OPC
Sets whether or not the screen brightness
is automatically adjusted according to
the lighting condition in the room. (OPC
setting: See this page.)
Backlight
The screen dims
The screen
brightens
Contrast
For less contrast
For more contrast
You can adjust the picture to your preference.
Follow the steps to adjust the picture.
1
cbutton
Brightness
For less brightness
For more brightness
Colour
For less colour
intensity
For more colour
intensity
Tint
Skin tones become
purplish
Skin tones become
greenish
For more sharpness
Sharpness
For less sharpness
Advanced
For finer picture adjustments. (See page 34).
Reset
Resets all picture adjustment items to the
factory preset values.
[Picture]
Picture
AV Mode
H OPC (Optical Picture Control) setting
Audio
You can set the TV to automatically adjust the screen
to suitable backlight brightness according to the
lighting conditions.
[STANDARD]
OPC
[Off]
Backlight
[+16]
Contrast
[ 30]
+
Brightness [
0]
+
Colour
[
0]
+
Tint
[
0]
Sharpness [
0]
+
Advanced
OPC indicator
Using OPC on the remote control unit
Reset
3
Press a/b to select the desired menu item.
Press ENTER to proceed if necessary.
4
Press a/b or c/d to select the desired item
or adjust the item to the desired level. Press
ENTER if necessary.
NOTE
• For resetting all adjustment items to factory preset values,
pressa/b to select “Reset”, press ENTER, press a/b to
select “Yes”, and then press ENTER.
• “Backlight” cannot be adjusted when “OPC” is set to “On”
or “On (Display)”.
• Select “Advanced” and then press ENTER to set “Colour
Temp.”, “Film Mode”, “Black”, “3D-Y/C” or “Monochrome”.
See page 34.
Press OPC to switch the OPC function on and off.
Using OPC on the menu screen
You can also set the menu screen.
Selected item
Description
On (Display)
Displays the OPC effect on the screen
while adjusting the brightness of the
screen.
On
Automatically adjusts
Off
The brightness is fixed at the value set in
“Backlight” (See this page).
OPC indicator
Light off
“Off” is selected in the OPC setting.
Lighted (Green) “On” or “On (Display)” is selected in the
OPC setting.
NOTE
• Make sure no object obstructs the OPC sensor, which
could affect its ability to sense surrounding light.
33
32A33X_en_e.indd 33
2008-1-31 13:00:14
Watching TV
Advanced picture settings
The advanced settings enable you to set the picture
adjustment in more detail. There are five options you
can choose from.
1
Press MENU and the MENU screen displays.
2
Press c/d to select “Picture”.
3
Press a/b to select “Advanced”, and then
press ENTER.
4
Press a/b to select the desired menu, and
then press ENTER.
5
Press a/b to select the desired level, and
then press ENTER if necessary.
H 3D-Y/C
Provides high quality images with minimal dot crawl
and cross colour noise.
Selected item
H Colour Temp. (Colour Temperature)
Description
Standard
Normal adjustment
Fast
For movie image
Slow
For still image
Off
3D-Y/C off
NOTE
• 3D-Y/C is not selectable depending on the input signal
type.
• 3D-Y/C may not operate depending on the input signal
type or noisy input signal.
H Monochrome
For viewing images in monochrome.
Adjusts the colour temperature to give the best white
image.
Selected item
High
Mid-High
Middle
Mid-Low
Low
Description
White with bluish tone
White with reddish tone
H Film Mode
Automatically detects a film-based source (originally
encoded at 24/25 frames/second, depending on the
vertical frequency), analyses it then recreates each still
film frame for high-definition picture quality.
H Black
For easier viewing, change the viewing depth by
selecting a level for automatically adjusting the dark
portion of an image.
Selected item
Description
On
For high detail in black portions
Off
No adjustment
34
32A33X_en_e.indd 34
2008-1-10 8:29:25
Watching TV
Other picture settings
DNR (Digital Noise Reduction)
Reduces noise on the screen and produces a clearer
video image.
1
Press MENU and the MENU screen displays.
2
Press c/d to select “Option”.
3
Press a/b to select “DNR”, and then press
ENTER.
4
Press a/b to select the desired level, and
then press ENTER.
Game Play Time
This function displays the elapsed game time so you
do not lose track of the time.
To display the elapsed time, select “GAME” under “AV
Mode” for the input mode of the terminal connected to
the game console before starting the game.
1
Press MENU and the MENU screen displays.
2
Press c/d to select “Option”.
3
Press a/b to select “Game Play Time”, and
then press ENTER.
4
Press a/b to select “On”, and then press
ENTER.
Select desired item
Off
High
Low
Selected item
On
The elapsed time is displayed every 30
minutes when you switch to GAME mode
in external input mode.
Off
No adjustment
Adjusting the image position
For adjusting a picture's horizontal and vertical position.
1
Press MENU and the MENU screen displays.
2
Press c/d to select “Setup”.
3
Press a/b to select “Position”, and then
press ENTER.
4
Press a/b to select “H-Position” or
“V-Position”.
Description
Set value at desired level
H-Position [ 0]
+
V-Position
+
[ 0]
Reset
Selected item
Description
H-Position
Centres the image by moving it to the left
or right.
V-Position
Centres the image by moving it up or
down.
5
Press c/d to adjust the item to your desired
position.
NOTE
• For resetting all adjustment items to the factory preset values,
press a/b to select “Reset”, and then press ENTER.
• Adjustments are stored separately according to input
source.
• Images may not be displayed properly depending on the
settings and/or signals.
32A33X_en_f.indd 35
35
2008-1-4 20:15:51
Watching TV
Audio adjustment
You can adjust the audio of the selected AV mode.
1
2
Press MENU and the MENU screen displays.
Press c/d to select “Audio”.
Audio
Power Control
Output Volume Select
Allows you to select what controls the audio output.
1
Press MENU and the MENU screen displays.
2
Press c/d to select “Option”.
3
Press a/b to select “Output Volume Select”,
and then press ENTER.
4
Press a/b to select “Fixed” or “Variable”, and
then press ENTER.
STANDARD
Treble
[ 0]
-
+
Bass
[ 0]
-
+
Balance
[ 0]
L
R
Surround
Reset
Select desired item
3
Press a/b to select the desired menu item.
Press ENTER to proceed if necessary.
4
Press a/b or c/d to select the desired item
or adjust the item to the desired level. Press
ENTER if necessary.
Selected item
cbutton
dbutton
Treble
For weaker treble
For stronger treble
Bass
For weaker bass
For stronger bass
Balance
Decrease audio from
the right speaker
Decrease audio
from the left speaker
NOTE
• For resetting all adjustment items to the factory preset
values, press a/b to select “Reset”, press ENTER, press
a/b to select “Yes”, and then press ENTER.
H Surround
When you set to “On”, you can enjoy surround sound,
the same as if you were in a movie theatre.
Selected item
Fixed
Variable
Selected item
Description
Fixed
• Sound via speakers is adjusted with VOL
e/f on the remote control unit or the
TV.
• Sound via the MONITOR OUTPUT
terminal is not adjustable and constantly
outputs.
Variable
• Sound via the MONITOR OUTPUT
terminal is adjusted with VOL e/f on
the remote control unit or the TV.
• Sound via speakers is muted.
NOTE
• The “Audio” menu cannot be operated when headphones
are plugged in or when “Variable” is selected.
Description
On
Makes it possible to enjoy natural,
realistic surround sound.
Off
Outputs the normal sound.
36
32A33X_en_f.indd 36
2008-1-4 20:15:53
Settings when using external devices
Settings when using HDMI output devices
HDMI terminals can carry audio and visual signals to the TV with an HDMI certified cable. When you want to output
the audio and picture from an HDMI output device on the TV, select “INPUT3” or “INPUT4” by switching the input
source.
Connecting an HDMI output device
HDMI output
device
HDMI cable (commercially available)
H HDMI (High-Definition Multimedia Interface)
terminal selection
1
To watch an HDMI equipment image, select
“INPUT3” or “INPUT4” using direct key IN3
(HDMI), IN4 (HDMI), TV/VIDEO on the
remote control unit or TV/VIDEO on the TV.
2
Press MENU and the MENU screen displays.
3
Press c/d to select “Option”.
4
Press a/b to select “HDMI Setup”, and then
press ENTER.
• The HDMI Setup can be selected only when
“INPUT3” or “INPUT4” is selected.
MENU
[Option ... HDMI Setup]
Option
HDMI Setup
items
Selectable
items
Description
Auto View
Enable/
Disable
Set whether or not to use
WIDE MODE based on
signal recognition, including
an HDMI signal.
Audio
Select
Digital/
Analogue
Select “Digital” for audio
signal via the HDMI terminal.
Select “Analogue” for audio
signal via the AUDIO jack.
NOTE
• Refer to your external equipment operation manual for the
above settings.
• When connecting a DVI-HDMI conversion adaptor/cable to
the HDMI terminal, the image may not come in clearly.
• “Audio Select” is only available for INPUT3.
AQUOS LINK Setup
DNR
Input Select
Output Volume Select
Audio Only
Game Play Time
Colour System
HDMI Setup
Fine Sync.
5
Press a/b to select the desired item, and
then press ENTER.
37
32A33X_en_f.indd 37
2008-1-4 20:15:53
Settings when using external devices
Selecting the input source and
signal type
Selecting input source
Can use for selecting the input source.
Using TV/VIDEO on the remote control unit or on
the TV
TV/VIDEO allows you to choose from the available
input sources.
Selecting input signal type
For setting the signal type of external equipment.
1
Press MENU and the MENU screen displays.
2
Press c/d to select “Option”.
3
Press a/b to select “Input Select”, and then
press ENTER.
4
Press a/b to select a signal type you want to
set, and then press ENTER.
Input source
1
2
Press TV/VIDEO on the remote control unit or
on the TV.
Press TV/VIDEO on the remote control unit or
on the TV to select the input source.
• The image and sound from the selected source
are output on the TV.
• You can also select the input source by pressing
a/b.
Selectable item
INPUT 1
Auto, COMPONENT, S-VIDEO, VIDEO
INPUT 2
Auto, COMPONENT, VIDEO
NOTE
• If no colour image displays, try changing the other
signal type.
• Check the operation manual of the external equipment for
the signal type.
• When the signal type is set to “Auto”, the input terminal
where a cable is connected is automatically selected.
• When the signal type is set to “Auto” and multiple video
signal cables are connected, the signal type is selected in
the following prioritised order:
INPUT 1: COMPONENT s S-VIDEO s VIDEO
INPUT 2: COMPONENT s VIDEO
38
32A33X_en_f.indd 38
2008-1-4 20:15:53
Settings when using external devices
Labelling input sources
You can assign each input source a label as you
prefer.
1
2
Press TV/VIDEO to select the desired input
source.
Press MENU and the MENU screen displays.
Skipping HDMI/PC input
This setting allows you to skip the HDMI or PC input
on the Input Selection Operation.
1
Press MENU and the MENU screen displays.
2
Press c/d to select “Setup”.
3
Press a/b to select “Input Skip”, and then
press ENTER.
4
Press a/b to select the Input (INPUT 3 to
INPUT 5) you wish to skip, and then press
ENTER.
INPUT 3
3
Press c/d to select “Setup”.
4
Press a/b to select “Input Label”, and then
press ENTER.
Select desired item
INPUT 4
INPUT 5
Yes
No
• When an HDMI input terminal (INPUT 3 and
INPUT 4) is selected, a Menu screen for selecting
“Auto” or “Manual” is displayed.
• When you select “Auto” using a/b, the Menu
screen returns to the “Input Label” Menu screen.
5
Press a/b to select characters and c/d
to move to the desired digit to label the input
source.
• When you want to change the input label that you
have already assigned to the default name, press
c/d to move to “CLEAR” on the “Input Label”
screen, and then press ENTER.
6
Repeat the above until the name is fully spelt
out, and then press MENU.
• The name can be 6 characters or less.
• When you want to set an input source name of
less than 6 characters, press MENU to exit from
the labelling menu.
5
Press a/b to select “Yes”, and then press
ENTER.
6
Press MENU to exit.
Colour system settings
You can change the colour system to one that is
compatible with the image on the screen.
1
Press MENU and the MENU screen displays.
2
Press c/d to select “Option”.
3
Press a/b to select “Colour System”, and
then press ENTER.
4
Press a/b to select a compatible video signal
system of your equipment, and then press
ENTER.
TV
INPUT1
INPUT2
DVD
Select desired item
AUTO
INPUT4
PAL
SECAM
(Example)
NTSC 3. 58
NTSC 4. 43
NOTE
• You cannot change labels if the input source is TV.
PAL-60
NOTE
• Factory preset value is “AUTO”.
• If “AUTO” is selected, colour system for each channel is
automatically set. If an image does not display clearly,
select another colour system (e.g. PAL, NTSC 4.43).
• “Colour System” is selectable only when inputting an
S-VIDEO or composite signal.
32A33X_en_f.indd 39
39
2008-1-4 20:15:53
AQUOS LINK
Controlling HDMI devices using AQUOS LINK
What is AQUOS LINK?
Using the HDMI CEC (Consumer Electronics Control) protocol, with AQUOS LINK you
can interactively operate compatible system devices (AV amplifier, DVD, Blu-ray Disc
device) using a single remote control.
NOTE
• AQUOS LINK-compatible AQUOS BD Player, 1 BIT THEATER RACK SYSTEM (AQUOS
AUDIO) and AQUOS Recorder are to be on sale after the release of this TV. (As of January
2008)
What you can do with AQUOS LINK
✔ One Touch Play
While the TV is in standby mode, it automatically turns on and plays back the image
from the HDMI source.
✔ Single remote control operation
The AQUOS LINK automatically recognises the connected HDMI device and you can
control the TV and the devices as if using a universal remote control.
✔ Operating Title list of external devices
You can also call up the external player’s Top menu or AQUOS BD Player’s/AQUOS
Recorder’s Title list provided that the devices support AQUOS LINK.
✔ Multiple control of HDMI devices
You can select which HDMI device to operate using OPTION.
✔ Controlling the 1 BIT THEATER RACK SYSTEM (AQUOS AUDIO)
You can adjust the volume and select the sound mode of the 1 BIT THEATER RACK
SYSTEM (AQUOS AUDIO).
NOTE
• Point the remote control toward the TV, not to the connected HDMI device.
• Video noise may occur depending on the type of HDMI-certified cable used. Make sure to use
a HDMI-certified cable.
• Up to 3 pieces of HDMI recording equipment and one AV amplifier can be connected using
this system.
• These operations affect the HDMI device selected as the current input source. If the device
does not operate, turn on the device and select the appropriate input source using TV/VIDEO.
• When you insert/remove HDMI-certified cables or change connections, turn on all connected
HDMI devices before turning on the TV. Confirm that picture and audio are correctly output by
selecting “INPUT3” or “INPUT4” from the INPUT SOURCE menu.
40
32A33X_en_f.indd 40
2008-1-12 14:49:08
AQUOS LINK
AQUOS LINK connection
First connect the 1 BIT THEATER RACK SYSTEM (AQUOS AUDIO) or an AQUOS BD Player/AQUOS Recorder
that supports the HDMI CEC protocol.
NOTE
• Refer to the operation manual of the device to be connected for further details.
• After unplugging connection cables or changing the connection pattern, first turn on the power of the TV with all relevant
device’s power turned on. Change the external input source by pressing TV/VIDEO, select the appropriate input source and
verify the audiovisual output.
• The cables illustrated in the following explanation are commercially available items.
Connecting an AQUOS BD Player/AQUOS
Recorder via the AQUOS AUDIO
Connecting an AQUOS BD
Player/AQUOS Recorder only
Output connection
HDMIcertified
cable
HDMI-certified
cable
AUDIO cable (commercially available)
To Analogue Audio (L/R)
input terminal
AQUOS BD Player/
AQUOS Recorder
AQUOS BD Player/
AQUOS Recorder
HDMI-certified cable
1 BIT THEATER
RACK SYSTEM
AQUOS LINK Setup
AQUOS LINK Auto power on
4
If this is activated, the One Touch Play function
is enabled. While the TV is in standby mode, it
automatically turns on and plays back the image from
the HDMI source.
Press a/b to select “Auto Power On”, and
then press ENTER.
Auto Power On
Selecting Recorder
On
Off
1
Press MENU and the MENU screen displays.
2
Press c/d to select “Option”.
3
Press a/b to select “AQUOS LINK Setup”,
and then press ENTER.
32A33X_en_f.indd 41
5
Press a/b to select “On”, and then press
ENTER.
6
Press MENU to exit.
NOTE
• The factory default for this item is “Off”.
41
2008-1-31 13:00:42
AQUOS LINK
Selecting recorder
Operating an AQUOS LINK device
You can select a recorder for the recording from
several connected recorders.
1
Repeat steps 1 to 3 in AQUOS LINK Auto
power on.
2
Press a/b to select “Selecting Recorder”,
and then press ENTER.
AQUOS LINK allows you to operate the HDMIconnected device with one remote control.
Use the following procedure to start playback.
1
Press PLAY I to start playback of a title.
2
Press FWD J to fast forward.
Press REV G to reverse.
Press STOP H to stop.
Press POWER to turn the HDMI-connected
device on/off.
Auto Power On
• See page 43, section “Playback of titles using
AQUOS LINK” if you want to start playback using
the list of the titles of the AQUOS BD Player/
AQUOS Recorder.
Selecting Recorder
INPUT3
[1. 0. 0. 0]
INPUT4
[2. 0. 0. 0]
3
Select the recorder, and then press ENTER.
4
Press MENU to exit.
Use the following procedure to start recording.
Check the following items before recording.
• Make sure the antenna cable is connected properly.
• Check if the recording media (HDD, DVD, etc.) has enough
capacity for recording a programme.
• Select the equipment for recording in Selecting Recorder.
NOTE
• If you have connected the 1 BIT THEATER RACK SYSTEM
(AQUOS AUDIO) between the TV and an AQUOS Recorder,
the input source’s indication changes from “INPUT3” to
“INPUT3 (Sub)” as it is shown below.
1
After you selected recording media (HDD,
DVD, etc.) in the menu, please make sure the
recording menu in the ready condition.
2
Press REC E to record a programme.
3
Press REC STOP H to stop recording.
Auto Power On
Selecting Recorder
INPUT3
[1. 0. 0. 0]
INPUT3 (Sub)
[1. 1. 0. 0]
INPUT4
[2. 0. 0. 0]
Listening with the 1 BIT THEATER RACK
SYSTEM (AQUOS AUDIO)
You can opt to listen to the TV sound only from the 1
BIT THEATER RACK SYSTEM (AQUOS AUDIO).
1
Press OPTION and the AQUOS LINK menu
screen displays.
2
Press a/b to select “By AQUOS AUDIO SP”,
and then press ENTER.
AQUOS LINK Menu
Recorder EPG
Top Menu/Title List
Media change
By AQUOS AUDIO SP
By AQUOS SP
Sound mode change
Model select
• The sound from the TV speaker and headphone
terminal is silenced and only the sound from the 1
BIT THEATER RACK SYSTEM (AQUOS AUDIO) is
audible.
• You can use VOL k/l and MUTE (e).
42
32A33X_en_g.indd 42
2008-1-31 13:01:17
AQUOS LINK
Listening with the AQUOS TV speaker
system
You can opt to listen to the TV sound only from the
AQUOS TV speaker system.
1
Press OPTION and the AQUOS LINK menu
screen displays.
2
Press a/b to select “By AQUOS SP”, and
then press ENTER.
Playback of titles using AQUOS LINK
This section explains how to play back a title in the
AQUOS BD Player/AQUOS Recorder.
Manually changing the AQUOS Audio
speaker system’s sound mode
1
2
Press OPTION and the AQUOS LINK menu
screen displays.
Press a/b to select “Sound mode change”.
AQUOS LINK Menu
Recorder EPG
Top Menu/Title List
1
Select the appropriate external input.
2
Press OPTION and the AQUOS LINK menu
screen displays.
3
Press a/b to select “Top Menu/Title List”,
and then press ENTER.
Media change
By AQUOS AUDIO SP
By AQUOS SP
Sound mode change
Model select
3
The sound mode changes every time you
press ENTER.
AQUOS LINK Menu
Recorder EPG
Top Menu/Title List
• Refer to the operation manual of the AQUOS
audio speaker system for details.
Media change
By AQUOS AUDIO SP
By AQUOS SP
Sound mode change
Model select
• The linked recorder now powers on and the TV
automatically selects the appropriate external
input source.
• The title list data from the connected AQUOS BD
Player/AQUOS Recorder displays.
4
Select the title with a/b/c/d, and then
press PLAY I to start playback.
43
32A33X_en_g.indd 43
2008-1-4 20:16:25
AQUOS LINK
Selecting media type for CEC-compatible
recorder
Recording via the AQUOS Recorder EPG
(only for recorders)
If your recorder has multiple storage media, select the
media type here.
You can call up the CEC-compatible recorder’s EPG
and preset timer recordings using the TV’s remote
control.
1
Press OPTION and the AQUOS LINK menu
screen displays.
2
Press a/b to select “Media change”, and
then press ENTER.
1
Press OPTION and the AQUOS LINK menu
screen displays.
2
Press a/b to select “Recorder EPG”, and
then press ENTER.
AQUOS LINK Menu
• The external input source switches and the
recorder’s EPG is displayed.
Recorder EPG
Top Menu/Title List
AQUOS LINK Menu
Media change
Recorder EPG
Top Menu/Title List
By AQUOS AUDIO SP
By AQUOS SP
Media change
Sound mode change
Model select
3
By AQUOS AUDIO SP
By AQUOS SP
Sound mode change
Model select
Select the desired medium, such as DVD or
HDD. The media type changes every time you
press ENTER.
3
HDMI device selection
Select the programme to record.
• Refer to the operation manual of the recorder for
details.
If multiple HDMI devices are connected in a daisy
chain, you can specify which device to control here.
1
Press OPTION and the AQUOS LINK menu
screen displays.
2
Press a/b to select “Model select”, and then
press ENTER. The HDMI device changes
every time you press ENTER.
44
32A33X_en_g.indd 44
2008-1-4 20:16:25
Connecting a PC
Use the PC terminals to connect a PC.
NOTE
• The PC INPUT terminals are DDC1/2B-compatible.
• Refer to page 50 for a list of PC signals compatible with the TV.
ANALOG
RGB
RGB cable
(commercially available)
Ø 3.5 mm stereo
minijack cable
(commercially available)
AUDIO
(L/R)
PC
Signal names for 15-pin mini D-sub connector
Pin No.
5
4
10
15
13
1
6
7
8
9
14
2
3
12
11
Signal name
R
G
B
Not connected
CSYNC
Pin No.
Signal name
GND (Ground)
GND (Ground)
GND (Ground)
+5V
GND (Ground)
Pin No.
Signal name
Not connected
SDA
HD
VD
SCL
NOTE
• Macintosh adaptor may be required for use for some Macintosh computers.
• Pin No. 5 is not used for inputting the signal.
Displaying a PC image on the screen
To view an image from a PC, select “INPUT 5” using
direct key PC, TV/VIDEO on the remote control unit or
TV/VIDEO on the TV.
TV
INPUT1
INPUT2
INPUT3
INPUT4
INPUT5
When connecting to a PC, the correct input signal type
is automatically detected. (See page 48.)
NOTE
• Each time TV/VIDEO is pressed, the input source toggles.
45
32A33X_en_g.indd 45
2008-1-4 20:16:25
Connecting a PC
Selecting the picture size
You can select the picture size as illustrated below.
NOTE
• Connect the PC before making adjustments.
• Selectable picture size may vary with input signal type.
Connecting a PC
ANALOG
RGB
RGB cable
(commercially available)
Ø 3.5mm stereo
minijack cable
(commercially available)
AUDIO
(L/R)
PC
1
Press WIDE.
• The WIDE MODE menu displays.
WIDE MODE
Normal
Full
(Example)
2
Press WIDE or a/b to select a desired item
on the menu.
a
Picture size images.
Input Signal
1024 g 768
1360 g 768
Normal
Keeps the original aspect
ratio in a full screen
display.
Full
An image fully fills the
screen.
46
32A33X_en_g.indd 46
2008-1-4 20:16:25
Connecting a PC
Adjusting the PC image automatically
This function enables the screen to be automatically
adjusted to its best possible condition when the
analogue terminals of the TV and PC are connected
with a commercially available RGB cable, etc.
Adjusting the PC image manually
Ordinarily you can easily adjust the picture as
necessary to change image position using Auto Sync.
In some cases, however, manual adjustment is needed
to optimise the image.
1
Press MENU and the MENU screen displays.
1
Press MENU and the MENU screen displays.
2
Press c/d to select “Option”.
2
Press c/d to select “Option”.
3
Press a/b to select “Fine Sync.”, and then
press ENTER.
3
Press a/b to select “Fine Sync.”, and then
press ENTER.
4
Press a/b to select “Auto Sync.”, and then
press ENTER.
4
Press a/b to select a specific adjustment
item among “H-Position”, “V-Position”, “Clock”
and “Phase”.
5
Press a/b to select “Yes”, and then press
ENTER.
Input Signal
Auto Sync.
• Auto Sync. starts.
Select desired item
Input Signal
Auto Sync.
H-Position
[
0]
V-Position
[
0]
Clock
[
0]
Phase
[
0]
H-Position
[90]
+
V-Position
[60]
+
Clock
[90]
+
Phase
[ 8]
+
Reset
Yes
No
Reset
NOTE
• Auto Sync. is likely to succeed when an input PC image
has wide vertical stripes (e.g. pattern with high contrast
stripes, or cross-hatched).
It may fail when an input PC image is solid (low contrast).
• Be sure to connect the PC to the TV and switch it on
before starting Auto Sync.
Selected item
Description
H-Position
Centres the image by moving it to the left
or right.
V-Position
Centres the image by moving it up or
down.
Clock
Adjusts when the image flickers with
vertical stripes.
Phase
Adjusts when characters have low
contrast or when the image flickers.
5
Press c/d to adjust the item to your desired
position.
NOTE
• For resetting all adjustment items to the factory preset
values, press a/b to select “Reset”, and then press
ENTER.
• Images may not be displayed properly depending on the
settings and/or input signals.
47
32A33X_en_g.indd 47
2008-1-4 20:16:25
Connecting a PC
Input resolution settings
Selecting the input resolution
• Some input signals may have to be registered manually to
display properly.
• The pairs of input signals (resolutions) in the list below are
not distinguishable when received. In such case, you have
to set the correct signal manually. After setting once, it will
display when the same signal (resolution) is input again.
1024 x 768
1360 x 768
NOTE
• You can only select the “Input Signal” on the Setup menu
when receiving one of the 2 input signals listed above.
1
Press MENU and the MENU screen displays.
2
Press c/d to select “Option”.
3
Press a/b to select “Fine Sync.”, and then
press ENTER.
4
Press a/b to select “Input Signal”, and then
press ENTER.
5
Press a/b to select the desired input signal
on the display, and then press ENTER.
Input Signal
Select desired item
Auto Sync.
H-Position
1024 x 768
V-Position
Clock
1360 x 768
Phase
Reset
(Example)
48
32A33X_en_g.indd 48
2008-1-4 20:16:26
Connecting a PC
PC Control of the TV
• When a programme is set, the TV can be controlled from the PC using the RS-232C terminal.
The input signal (PC/video) can be selected, the volume can be adjusted and various other adjustments and
settings can be made, enabling automatic programmed playing.
• Attach an RS-232C cable cross-type (commercially available) to the Din/D-sub RS-232C for the connections.
NOTE
• This operation system should be used by a person who is accustomed to using PCs.
Communication conditions
Set the RS-232C communications settings on the PC to match the communications conditions of the TV. The
communications settings of the TV are as follows:
Baud rate:
9,600 bps
Data length:
8 bits
Parity bit:
None
Stop bit:
1 bit
Flow control:
None
Communication procedure
Send the control commands from the PC via the RS-232C connector.
The TV operates according to the received command and sends a response message to the PC.
Do not send multiple commands at the same time. Wait until the PC receives the OK response before sending the
next command.
Command format
Eight ASCII codes e CR
C1 C2 C3 C4 P1 P2 P3
Command 4-digits
Parameter 4-digits
P4
Command 4-digits: Command. The text of four characters.
Parameter 4-digits: Parameter 0 — 9, space, ?
Return code
Parameter
Input the parameter values, aligning left, and fill with space(s) for the remainder. (Be sure that four values are input for the
parameter.)
When the input parameter is not correct, “ERR” returns. (Refer to “Response code format”.)
0
0
0
0
a
3
0
1
0
0
0
0
5
9
5
When “?” is input for some commands, the present setting value responds.
?
?
?
?
?
Response code format
Normal response
O
K
Problem response (communication error or incorrect command)
E
Return code (0DH)
R
R
Return code (0DH)
49
32A33X_en_h.indd 49
2008-1-4 20:16:55
Connecting a PC
PC compatibility chart
Horizontal Vertical
VESA
Frequency Frequency Standard
Resolution
VGA
SVGA
1024 g 768
48.4 kHz
60 Hz
✓
1024 g 768
56.5 kHz
70 Hz
✓
1024 g 768
60.0 kHz
75 Hz
✓
1360 g 768
47.7 kHz
60 Hz
✓
1280 g 1024
64.0 kHz
60 Hz
✓
SXGA+ 1400 g 1050
65.3 kHz
60 Hz
✓
720 g 400
31.5 kHz
70 Hz
640 g 480
31.5 kHz
60 Hz
✓
640 g 480
37.9 kHz
72 Hz
✓
640 g 480
37.5 kHz
75 Hz
✓
WXGA
800 g 600
35.1 kHz
56 Hz
✓
SXGA
800 g 600
37.9 kHz
60 Hz
✓
800 g 600
48.1 kHz
72 Hz
✓
800 g 600
46.9 kHz
75 Hz
✓
Horizontal Vertical
VESA
Frequency Frequency Standard
Resolution
XGA
DDC is a registered trademark of Video Electronics Standards Association.
Power Management is a registered trademark of Sun Microsystems, Inc.
VGA and XGA are registered trademarks of International Business Machines Corp.
RS-232C commands list
Commands
• Commands not indicated here are not guaranteed to operate.
CONTROL ITEM
COMMAND
CONTROL
CONTENTS
PARAMETER
CONTROL ITEM
COMMAND
CONTROL
CONTENTS
PARAMETER
POWER SETTING
P O W R 0
_
_
_
POWER OFF (STANDBY)
VOLUME
V O L M *
INPUT SELECTION A
I
T G D _
_
_
_
INPUT SWITCHING (TOGGLE)
POSITION
H P O S
* * * _ H-POSITION (AV) (f10—10)
I
T V D _
_
_
_
TV (CHANNEL FIXED)
H P O S
* * * _ H-POSITION (PC) (0—180)
I
A V D *
_
_
_
INPUT1—5 (1—5)
V P O S
* * * _ V-POSITION (AV) (f20—20)
CHANNEL
INPUT SELECTION B
AV MODE
SELECTION
* _ _ VOLUME (0—60)
D C C H *
* _ _ TV DIRECT CHANNEL (1—99)
V P O S
* * * _ V-POSITION (PC) (0—120)
C H U P _
_
_
_
CHANNEL UP
C L C K
* * * _ CLOCK (0—180)
C H D W _
_
_
_
CHANNEL DOWN
P H S E
* * _ _ PHASE (0—15)
I
N P 1 0
_
_
_
INPUT1 (Auto)
I
N P 1 1
_
_
_
I
N P 1 2
_
_
I
N P 1 3
_
I
N P 2 0
I
I
W I
D E 0
_
_
_
TOGGLE
INPUT1 (COMPONENT)
W I
D E 1
_
_
_
NORMAL
_
INPUT1 (S-VIDEO)
W I
D E 2
_
_
_
ZOOM 14:9
_
_
INPUT1 (VIDEO)
W I
D E 3
_
_
_
PANORAMA
_
_
_
INPUT2 (Auto)
W I
D E 4
_
_
_
FULL
N P 2 1
_
_
_
INPUT2 (COMPONENT)
W I
D E 5
_
_
_
CINEMA 16:9
N P 2 3
_
_
_
INPUT2 (VIDEO)
W I
D E 6
_
_
_
CINEMA 14:9
A V M D 0
_
_
_
TOGGLE
W I
D E 7
_
_
_
UNDERSCAN
A V M D 1
_
_
_
STANDARD
M U T E 0
_
_
_
TOGGLE
A V M D 2
_
_
_
MOVIE
M U T E 1
_
_
_
MUTE ON
A V M D 3
_
_
_
GAME
M U T E 2
_
_
_
MUTE OFF
A V M D 4
_
_
_
USER
A C S U 0
_
_
_
SURROUND TOGGLE
A V M D 5
_
_
_
DYNAMIC (FIXED)
A C S U 1
_
_
_
SURROUND ON
A V M D 6
_
_
_
DYNAMIC
A C S U 2
_
_
_
SURROUND OFF
A V M D 7
_
_
_
PC
AUDIO CHANGE
A C H A _
_
_
_
TOGGLE
SLEEP TIMER
O F T M 0
_
_ _
OFF
O F T M 1
_
_
_
SLEEP TIMER 30 MIN
O F T M 2
_
_
_
SLEEP TIMER 1 HOUR
O F T M 3
_
_
_
SLEEP TIMER 1 HOUR 30 MIN
O F T M 4
_
_
_
SLEEP TIMER 2 HOUR
O F T M 5
_
_
_
SLEEP TIMER 2 HOUR 30 MIN
NOTE
• If an underbar (_) appears in the parameter column, enter a
space.
• If an asterisk (*) appears, enter a value in the range
indicated in brackets under CONTROL CONTENTS.
WIDE MODE
MUTE
SURROUND
50
32A33X_en_h.indd 50
2008-1-10 8:29:53
Teletext function
About Teletext
What is Teletext?
Teletext broadcasts pages of information and
entertainment to specially equipped television sets.
Your TV receives Teletext signals broadcast by a TV
network, and decodes them into graphical format for
viewing. News, weather reports, sports information,
stock exchange prices and programme previews are
among the many services available.
TELETEXT
Teletext mode
Teletext is turned on/off with m on the remote control
unit. You can operate your TV in Teletext mode directly
by inputting commands with the remote control unit.
TELETEXT
When viewing the Teletext information
• Press CHr to increase the page number.
• Press CHs to decrease the page number.
NOTE
• When you turn TELETEXT on and change a Teletext page
right after changing channels, the relevant page may not
be displayed until the TV finishes reading all the Teletext
information.
Button functions
Colour (Red/Green/Yellow/Blue):
You can select a group or block of pages displayed
in the coloured brackets at the bottom of the screen
by pressing the corresponding Colour (Red/Green/
Yellow/Blue) on the remote control unit.
TELETEXT
Red
Turning on and off Teletext
1
Select a TV channel or external input source
providing the Teletext programme.
2
Press m to display the Teletext.
Green
Yellow
Blue
0 — 9:
Directly select any page from 100 to 899 by using 0 — 9.
v (Top/Bottom/Full):
Each time you press v, the TELETEXT image
switches as shown below.
Full (Displays in full screen)
Top (Displays in the upper half of the screen)
3
Press m again to display the Teletext on
the right screen and normal image on the left
screen.
• Each time you press m, the screen switches as
shown upper right.
• If you select a programme with no Teletext signal,
“No Teletext available.” is displayed.
Bottom (Displays in the lower half of the screen)
k (Reveal hidden for TELETEXT):
To reveal hidden information such as an answer to a
quiz, press k.
• Press k again to hide the information.
3 (Hold):
To stop updating Teletext pages automatically, press 3.
• Press 3 again to release the hold mode.
51
32A33X_en_h.indd 51
2008-1-4 20:16:56
Teletext function
Displaying Subtitles
You can display subtitles as they are transmitted.
1
Press [ to display the subtitle.
2
Press [ to exit the subtitle screen.
Displaying Subpages
You can display subpages as they are transmitted.
• Subtitle is updated by information sent by the
broadcasting station.
• To stop updating subtitle automatically, press 3.
NOTE
• Subtitle will not be displayed when the service does not
contain subtitle information.
1
2
Press m to display Teletext.
Press 1 to display the subpage as shown
below.
Subpage screen
+
0002
00
01
02
03
3
Select the desired subpage by using c/d.
4
Press 1 to exit the subpage screen.
• 0 — 9 directly selects the desired subpage.
52
32A33X_en_h.indd 52
2008-1-4 20:16:56
Teletext function
Teletext language setting
If Teletext information does not display correctly,
perform the procedure below.
Select from among 4 kinds of language tables: West
Europe, East Europe, Turkish/Greek, Arabic/Hebrew.
Each table is compatible with the Teletext languages
listed below.
1
Press MENU and the MENU screen displays.
2
Press c/d to select “Setup”.
3
Press a/b to select “Text Language”, and
then press ENTER.
4
Press a/b to select receivable teletext
broadcasting language in your country, and
then press ENTER.
MENU
[Setup ... Text Language]
Select language
Arabic/Hebrew
West Europe
East Europe
Turkish/Greek
NOTE
• Teletext can display only when it is sent by a network. Not
used to convert between languages.
53
32A33X_en_h.indd 53
2008-1-4 20:16:56
Appendix
Troubleshooting
The problems described below are not always caused by malfunctions. Check the TV again before having the TV
serviced.
Problem
Possible Solution
• No power.
• Check if you pressed POWER on the remote control unit. (See page 14.)
If the indicator on the TV lights up red, press POWER.
• Is the AC cord disconnected? (See page 10.)
• Has the power been turned on? (See page 14.)
• Unit cannot be operated.
• External influences such as lightning, static electricity, etc., may cause improper
operation. In this case, operate the unit after first turning the power off the TV or
unplugging the AC cord and re-plugging it in after 1 or 2 minutes.
• Remote control unit does not
operate.
•
•
•
•
• Picture is cut off.
• Is the image position correct? (See page 35.)
• Are screen mode adjustments such as picture size made correctly? (See pages 30,
31 and 46.)
• Strange colour, light colour, or
dark, or colour misalignment.
•
•
•
•
•
• Power is suddenly turned off.
• The unit’s internal temperature has increased.
Remove any objects blocking the vent or clean.
• Check the power control setting. (See pages 28 and 29.)
• Is the sleep timer set? (See page 28.)
• No picture.
• Is the connection to external equipment correct? (See pages 11, 12, 37, 45 and 46.)
• Has the input signal setup been performed correctly after connection? (See page
48.)
• Is the correct input selected? (See page 38.)
• Is the picture adjustment correct? (See pages 33 to 35.)
• Is the antenna connected properly? (See page 10.)
• Is “On” selected in “Audio Only”? (See page 25.)
• No sound.
• Is the volume too low? (See page 19.)
• Make sure that headphones are not connected. (See page 8.)
• The TV sometimes makes a
cracking sound.
• This is not a malfunction. This happens when the cabinet slightly expands and
contracts according to changes in temperature. This does not affect the TV’s
performance.
Are batteries inserted with polarity (e, f) aligned? (See page 13.)
Are batteries worn out? (Replace with new batteries.)
Are you using it under strong or fluorescent lighting?
Is a fluorescent light shining on the remote control sensor?
Adjust the picture tone. (See pages 33 to 35.)
Is the room too bright? The picture may look dark in a room that is too bright.
Check the colour system setting. (See pages 21 and 39.)
Check the input signal setting. (See page 48.)
Check the HDMI Setup setting. (See page 37.)
Cautions regarding use in high and low temperature environments
• When the unit is used in a low temperature space (e.g. room, office), the picture may leave trails or appear slightly delayed.
This is not a malfunction, and the unit will recover when the temperature returns to normal.
• Do not leave the unit in a hot or cold location. Also, do not leave the unit in a location exposed to direct sunlight or near a
heater, as this may cause the cabinet to deform and the LCD panel to malfunction.
Storage temperature: f20°C to e60°C.
54
32A33X_en_i.indd 54
2008-1-4 20:17:26
Appendix
Error messages about recording using AQUOS LINK
The example of an error message
displayed on a screen
Error code
Failed to record
Cannot record the broadcast.
S05
Failed to record
Cannot record the broadcast.
S06
Failed to record
Cannot record the broadcast.
S07
Failed to record
S09
Failed to record
S10
Failed to record
S11
Failed to record
S12
Failed to record
Cannot record the programme.
S13
Failed to record
Cannot record the programme.
S14
Failed to record
No record media available.
S16
Failed to record
Cannot record while playback.
S17
Failed to record
Cannot record while recording other
programme.
S18
Failed to record
No record media available.
S19
Failed to record
Cannot record while not receiving
broadcast.
S20
Failed to record
No record media available.
S21
Failed to record
No recordable memory available.
S22
Failed to record
Age limitation is set.
S23
Failed to record
Cannot record with the recorder.
S31
Possible Solution
Check the content (broadcast or programme)
or the recording medium such as HDD or DVD.
Either the content or the recording medium may
be incompatible.
This network cannot be recorded.
Use the recording function of your recording
device, not the AQUOS LINK function.
Use the recording function of your recording
device, not the AQUOS LINK function.
Check the content (broadcast or programme).
It may be incompatible.
Check the recording medium.
Stop playback and set up the recording again.
During recording, another recording is not possible.
Check the recording medium.
Writing to the medium is prohibited.
Please check if the settings are properly set.
Broadcasts are not receivable.
Recording to the medium is not possible. Check
the recording medium.
Check the capacity of the recording medium.
Deactivate the child lock and set up the
recording again.
Check your recording device.
55
32A33X_en_i.indd 55
2008-1-4 20:17:28
Appendix
Reset
If complex adjustments are made and the settings
cannot be restored to normal, you can reset the
settings to the factory preset values.
1
Press MENU and the MENU screen displays.
2
Press c/d to select “Setup”.
3
Press a/b to select “Reset”, and then press
ENTER.
4
Press a/b to select “Yes”, and then press
ENTER.
• When “Reset” is completed, the backlight will turn
off and then on in a short period of time.
• The screen will be returned to its original state.
• “Execute auto installation” displays on the screen.
5
Press a/b to select “Yes” and then press
ENTER.
• “Auto installation” will be executed.
NOTE
• If you execute “Reset”, all the settings such as Picture,
Audio, Programme and Language will be reset to the
factory preset values.
56
32A33X_en_i.indd 56
2008-1-4 20:17:29
Appendix
Specifications
Model
LC-32A33X
LC-37A33X
LCD panel
32o (800 mm) Advanced Super View &
BLACK TFT LCD
37o (940 mm) Advanced Super View &
BLACK TFT LCD
Resolution
1,049,088 pixels (1366 g 768)
Video Colour System
PAL/SECAM/NTSC 3.58/NTSC 4.43/PAL 60
TV
Function
PAL: B/G, D/K, I SECAM: B/G, D/K, K/K1 NTSC: M
Item
TV-Standard
Receiving
Channel
VHF/UHF
44.25—863.25 MHz
CATV
S1—S41ch (including Hyperband)
TV-Tuning System
Auto Preset 99 ch
STEREO/BILINGUAL
NICAM: B/G, I, D/K A2 stereo: B/G
450 cd/m2 (at AV MODE Dynamic position)
Brightness
Backlight life
60,000 hours (at Backlight Standard position)
Viewing angles
H : 176º V : 176º
Audio amplifier
10W g 2
Speakers
10 g 4 cm 2pcs
Terminals
Rear
15 g 4 cm 2pcs
Antenna input
UHF/VHF 75 q DIN type
INPUT 1
VIDEO in, AUDIO in, S-VIDEO in,
COMPONENT in (480I, 576I, 480P, 576P, 720P/50Hz, 720P/60Hz, 1080I/50Hz, 1080I/60Hz)
INPUT 2
VIDEO in, AUDIO in,
COMPONENT in (480I, 576I, 480P, 576P, 720P/50Hz, 720P/60Hz, 1080I/50Hz, 1080I/60Hz)
INPUT 3
HDMI (HDMI input) (480P, 576P, 720P/50Hz, 720P/60Hz, 1080I/50Hz, 1080I/60Hz), AUDIO in
(Ø 3.5 mm jack)
INPUT 4
HDMI (HDMI input) (480P, 576P, 720P/50Hz, 720P/60Hz, 1080I/50Hz, 1080I/60Hz)
INPUT 5 (PC input) 15 pin mini D-sub, AUDIO in (Ø 3.5 mm jack)
MONITOR OUT
VIDEO out, AUDIO out
RS-232C
9 pin D-sub male connector
OSD language
English/Simplified Chinese/Traditional Chinese/Arabic
Power Requirement
AC 110—240 V, 50/60 Hz
Power Consumption
Weight
133 W (0.7 W Standby)
163 W (0.7 W Standby)
without stand
10.5 kg
14 kg
with stand
12.5 kg
16 kg
Operating Temperature
0°C — 40°C
• As a part of policy of continuous improvement, SHARP reserves the right to make design and specification changes for product
improvement without prior notice. The performance specification figures indicated are nominal values of production units. There
may be some deviations from these values in individual units.
Optional accessory
The listed optional accessory is available for the LCD colour
TV. Please purchase it at your nearest shop.
• Additional optional accessories may be available in the near
future. When purchasing, please read the newest catalogue for
compatibility and check the availability.
Part name
Model number
Wall mount bracket
(for LC-32A33X/
LC-37A33X)
AN-37AG5
57
32A33X_en_i.indd 57
2008-1-14 9:06:26
Appendix
Dimensional drawings
Unit: mm
LC-32A33X
402
74
95
776
395.9
55
335
523
578
701.5
230
110
200
200
58
32A33X_en_i.indd 58
2008-1-4 20:17:29
Appendix
Dimensional drawings
Unit: mm
LC-37A33X
402
71
904
96
463.8
55
370
585
640
824.4
230
100
200
200
59
32A33X_en_i.indd 59
2008-1-10 8:30:24
Appendix
Mounting the TV on the wall
Removing the stand
For wall mounting with the optional bracket, remove the stand.
Before detaching/attaching the stand
•
•
•
•
Before detaching (or attaching) the stand, unplug the AC cord from the AC outlet.
Remove all terminal covers and connected cables.
Lay the TV down on cushioning (such as a blanket) over a table.
Make sure two or more people perform the operation.
CAUTION
• Do not remove the stand from the TV unless using an optional bracket to mount it.
1
Hex key
2
Stand post
Unfasten the four screws used to secure the stand in
place.
1 Detach the stand from the TV. (Hold the stand so
it will not drop from the edge of the base area.)
2 Remove the stand post from the stand base and
attach it to the TV.
NOTE
• To attach the stand, perform the above steps in reverse order.
Handling and precautions with the wall-mounted TV
• You can mount the TV on the wall using the optional AN-37AG5 bracket.
• For details, refer to the instructions supplied with the optional bracket.
CAUTION
• This TV should be mounted on the wall only with the AN-37AG5 (SHARP) wall mount bracket. The use of other wall
mount brackets may result in an unstable installation and may cause serious injuries.
• Installing the Liquid Crystal Television requires special skill that should only be performed by qualified service
personnel. Customers should not attempt to do the work themselves. SHARP bears no responsibility for improper
mounting or mounting that results in accident or injury.
Using an optional bracket to mount the TV
• You can ask a qualified service personnel about using an optional AN-37AG5 bracket to mount the TV to the wall.
• Carefully read the instructions that come with the bracket before beginning work.
Hanging on the wall
AN-37AG5 wall mount bracket.
(See the bracket instructions for details.)
Vertical mounting
Angular mounting
About setting the TV angle
0/15/20°
0/5/1
AN-37AG5
NOTE
• Detach the cable clamps on the rear of the TV when using the optional mount bracket.
• To use this TV mounted on a wall, first remove the cover at the 4 locations on the rear of the TV, and then use the screws
supplied with the wall mount bracket to secure the bracket to the rear of the TV.
60
32A33X_en_i.indd 60
2008-1-12 14:50:39
Appendix
CLEARING THE PASSWORD
If you forget your password, set a new password using the following procedure.
1
Press MENU and the MENU screen displays.
2
Press c/d to select “Setup”.
3
Press a/b to select “Child Lock”, and then press ENTER.
4
The password input screen displays.
5
If you enter “3001” using 0 — 9, the “Child Lock” setting menu will be displayed.
6
Enter the 4-digit number as a password using 0 — 9. (See page 27.)
The new password is now set.
The Password is
.
NOTE
• As a precautionary measure, make a note of your password above, remove it from this manual, and keep it in a familiar place.
61
32A33X_en_i.indd 61
2008-1-4 20:17:29
Memo
62
32A33X_en_i.indd 62
2008-1-4 20:17:30
Memo
63
32A33X_en_i.indd 63
2008-1-4 20:17:30
Memo
64
32A33X_en_i.indd 64
2008-1-4 20:17:30
32A33X_Cover2.indd 1
2008-1-4 20:18:36
Printed in Malaysia
TINS-D483WJZZ
08P01-MA-NP
32A33X_Cover.indd 2
9/10/2008 10:12:54 AM
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement