BAND-IT A49099 A59099 Tie
Instruction
Manual
A50099
Calibration Device
TIE-DEX CALIBRATION DEVICE – A50099
Introduction:
The A50099 Tie-Dex Calibration Device is to be used with the A30199,
A40199, A35199, and A35599 Tools using BAND-IT Tie-Dex ties only.
Table of Contents:
1. Introduction & Safety Practices
2. Specifications & Contents
3. Operating Instructions
4. Operating Instructions
5. Operating Instructions
6. Replacement Parts & Warranty
Safety Practices:
1. Read this manual and become familiar with the device before use.
2. Protective eyewear should be worn during use.
3. Wear appropriate gloves for handling steel.
4. Care should be taken to insure fingers are not in contact with the Tie during
calibration.
WWW.CABLEJOINTS.CO.UK
BAND-IT-IDEX, Inc.
A Unit of IDEX Corporation
4799 Dahlia Street
Denver, CO 80216-0307 USA
P: 1-800-525-0758
F: 1-800-624-3925
THORNE & DERRICK UK
TEL 0044 191 490 1547 FAX 0044 477 5371
-ITTEL 0044 117 977 4647 FAX 0044 977 5582
WWW.THORNEANDDERRICK.CO.UK
A50099
Calibration Device
Specification &
Contents
Specifications:
Range: 50 lbf – 170 lbf
Accuracy: 2 lbf
Dimensions: 6.65" Long X 2.47" Wide X 2.83" Tall (Device)
Weight: 2 lbs (Device)
Tie-Dex Calibration Kit Contains the Following Items:
Calibration Device with
Interface, Tie-Dex II (factory installed on Device)
Interface, Micro Tie-Dex II
Test Band, 50pcs
Test Band, Micro, 50pcs
Calibration Adjustment Key
Hex Key, 1/16"
Hex Key, 9/64"
Carrying Case
Carrying Case
Calibration Device
1/16" Hex Key
9/64" Hex Key
Micro Test Band
Micro Interface
Test Band
Calibration Key
BAND-IT-IDEX, Inc.
A Unit of IDEX Corporation
4799 Dahlia Street
Denver, CO 80216-0307 USA
P: 1-800-525-0758
F: 1-800-624-3925
www.BAND-IT-IDEX.com
Page 2 of 6
Document # P29587 rev. G
© Copyright
BAND-IT-IDEX, Inc. 2010
All rights reserved
A50099
Calibration Device
Operating
Instructions
Note:
Calibration device must have 20-30 lbf pre-load to
ensure accuracy.
1 lbf = 1 psi Approx.
Rotate the load adjustment screw counter-clockwise
if gauge indicates the pre-load is less than 20 lbf.
Gauge
Load Adjustment
Screw
Tool Interfaces
Corresponding Tool
Etched on Interface
Band Release Button
Tie-Dex II
Micro Tie-Dex II
(A40199)
Comes factory installed
on Calibration Deivice
(A30199/A35599)
Calibration Adjustment Key
Oil-Filled Cylinder
Tie-Dex II Interface
BAND-IT-IDEX, Inc.
A Unit of IDEX Corporation
4799 Dahlia Street
Denver, CO 80216-0307 USA
P: 1-800-525-0758
F: 1-800-624-3925
www.BAND-IT-IDEX.com
Page 3 of 6
Document # P29587 rev. G
© Copyright
BAND-IT-IDEX, Inc. 2010
All rights reserved
A50099
Calibration Device
Operating
Instructions
1. Attach appropriate Tool Interface to Calibration Device (Tie-Dex II Interface comes factory
installed). Use Hex Keys provided with kit to remove and install Cap Screws and Flat Head
Screw.
2. Press Band Release Button and insert appropriate Test Band (be sure to use the correct test
band depending on the type of tool being calibrated). Test Band must be clean and
undamaged.
3. Insert other end of Test Band into the Tool band slot.
4. Actuate Pull-Up Lever on Hand Tool until Lever locks in place against Tool Body and preset
tension has been achieved. Be sure the Tool Head is nested in the Interface, as shown
below. If a Tie-Dex pneumatic tool (A35199, A35599) is being calibrated, be sure that the
cutoff disable switch is in the off position. Warning: do not cut off band while tool is being
calibrated.
5. At this point in the calibration procedure, the Gauge reading on the Calibration Device
indicates the pull-up force (lbf) that the Tie-Dex II tool is set to.
Cutoff Lever
Band Release Button
Tie-Dex II Hand
Tool
Calibration
Device
Pull-Up Lever
Test Band
Gripper Release
Lever
BAND-IT-IDEX, Inc.
A Unit of IDEX Corporation
4799 Dahlia Street
Denver, CO 80216-0307 USA
P: 1-800-525-0758
F: 1-800-624-3925
www.BAND-IT-IDEX.com
Page 4 of 6
Document # P29587 rev. G
© Copyright
BAND-IT-IDEX, Inc. 2010
All rights reserved
A50099
Calibration Device
Operating
Instructions
Tool Body
6. While the Pull-Up Lever is held up
against the Tool Body, press the Tension
Release Lever forward. This will unlock
the Pull-Up Lever. Next, actuate the
Gripper Release Lever and slide the Tool
away from the Calibration Device.
Cutoff Lever
Tension
Release Lever
7. Press the Band Release Button to
remove and discard used Test Band
Pull-Up Lever
Note: Band Release Button will not
actuate while Tie-Dex II Tool is in
Calibration Device.
Gripper Release
Lever
Calibration Key
8. If needed, adjust preset tension on TieDex II Tool. To adjust, remove Plug
from rear of Tool Body and insert
Calibration Key.
Rotate as needed.
Repeat instructions above to verify
calibration.
Rotate Clockwise to
Increase Tension
9. To qualify calibration, repeat calibration
steps 3 times using a fresh piece of Test
Band each time.
BAND-IT-IDEX, Inc.
A Unit of IDEX Corporation
4799 Dahlia Street
Denver, CO 80216-0307 USA
P: 1-800-525-0758
F: 1-800-624-3925
www.BAND-IT-IDEX.com
Page 5 of 6
Document # P29587 rev. G
© Copyright
BAND-IT-IDEX, Inc. 2010
All rights reserved
A50099
Calibration Device
Replacement Parts
& Warranty
The Calibration Device can be calibrated to within 2 lbf of
actual load frame readings in the 50 to 170 lbf range.
Remove the Interface and Rotate Calibration Adjustment Screw
clockwise to decrease calibration device reading and counterclockwise to increase readings.
1 full turn = 1 lbf Approx.
The Calibration Device may be returned to BAND-IT for
periodic calibration.
Each Calibration Device has its own serial number and
calibration history.
Calibration
Adjustment Screw
Replacement Parts
Interfaces
Part
Number
A50799
A50899
A50999
Used With
Kit Contents
A40199, A35199
A30199, A35599
A001
Interface, Cap Screws (x2), Flat Head Screw
Interface, Cap Screws (x2), Flat Head Screw
Interface, Top Support, Cap Screws (2), Flat Head Screw
Test Bands and Keys
Part
Number
A50599
A50699
A44699
Packaged
Quantity
50
50
1
Description
Test Band, Tie-Dex
Test Band, Tie-Dex Micro
Calibration Key, Tie-Dex
Refer to website for warranty information: http://www.band-it-idex.com/warranty.html
WWW.CABLEJOINTS.CO.UK
THORNE & DERRICK UK
TEL 0044 191 490 1547 FAX 0044 477 5371
TEL 0044 117 977 4647 FAX 0044 977 5582
WWW.THORNEANDDERRICK.CO.UK
BAND-IT-IDEX, Inc.
A Unit of IDEX Corporation
4799 Dahlia Street
Denver, CO 80216-0307 USA
P: 1-800-525-0758
F: 1-800-624-3925
www.BAND-IT-IDEX.com
Page 6 of 6
Document # P29587 rev. G
© Copyright
BAND-IT-IDEX, Inc. 2010
All rights reserved
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement