Manuale The Rooster
The Rooster device and logo copyright © 2007 Jon Bailes. All rights reserved.
WARNING
For your personal safety, please read this operating manual and
warning thoroughly before using the equipment.
This unit must be installed in such a manner that operator access
to the mains plug is maintained. Where the product is to be rack
mounted, this may be achieved by having access to the
disconnection device for the whole rack.
To reduce the risk of electric shock, it is essential that the unit is
disconnected from the mains supply before removing the cover.
Please also note that the power supply capacitors within this unit
can remain charged even after the mains supply has been
disconnected. It is essential that these capacitors are discharged
after the mains supply has been disconnected and the covers
have been removed.
In the event that this unit has been dropped or has suffered an
impact, an electrical safety test must be carried out before
reconnection to the mains supply.
This equipment is not intended for use in explosion hazard
environments. It must be used and stored in studio conditions,
such that the ambient relative humidity does not exceed 80%, nor
is the temperature to be allowed to drop to a level, which would
cause dew point to be reached.
Please ensure that adequate ventilation is provided and that the
ventilation slots are not obstructed. When rack mounting this
equipment, a fan may be required to provide sufficient airflow.
©Thermionic Culture Ltd., May 2008
1
CONTENTS
Section
Page
1
Introduction
3
2
Controls and meters
4
2.1
Phase switch
4
2.2
I/P switch
4
2.3
DI socket
4
2.4
I/P level control
4
2.5
Base lift control
4
2.6
Mid/Hi lift control
5
2.7
2.5k/4k/Hi switch
5
2.8
Mid Cut control
5
2.9
Bass Cut switch
5
2.10 LPF switch
6
2.11 Mode switch
6
2.12 Attitude switch
6
2.13 O/P level control
7
2.14 Off/48V switch
7
2.15 Meters
7
3
Operational hints and tips
8
4
Connections
9
5
Servicing and maintenance
10
5.1
Valves
10
5.2
Operating voltages and fuses
10
6
Specification
©Thermionic Culture Ltd., May 2008
11
2
1
Introduction
The Rooster is a valve device dedicated to bringing together
three facilities in one unit. It provides a high quality Mic / DI /
Line pre-amp, suitable for any type of microphone, DI or line
source. Then comes a unique sounding EQ section,
specially designed by Vic Keary, comprising broad but very
useable frequency bands with a ‘vari slope’ curve. This is
also a feature of the Earlybird 2 series of mic-amps. Finally,
the ability to change the amount of distortion, or THD, of the
unit as a whole is provided by the “Attitude” control,
combined with the ‘Mode’ switch. All of these features are
available on both of the unit’s 2 channels.
The Rooster will provide everything from a warm, clean
sounding valve mic-pre, suitable for any application, to a
characterful overdriven processor with powerful EQ, as
adaptable for adding dirt and edge to mics as it is for
mixdown treatment.
The user has control over the amount of THD that The
Rooster will add to the signal as well as the kind of
harmonics included in that THD. This is achieved by using
the same 5725 distortion valve as employed in Thermionic
Culture’s ‘Culture Vulture Mastering’ unit. The control over
gain given to the user can also be used to obtain more or
less THD included in the output signal. In addition to this the
EQ section can be used to tailor the sound of the distortion
at high THD levels or it may act as a more conventional tone
control at low distortion settings.
©Thermionic Culture Ltd., May 2008
3
2
Controls and meters
2.1
Phase switch
Controls the absolute phase of the signal. The ‘NonInv’ position does not alter the phase of the signal
applied to the input. Whereas, the ‘Invert’ position puts
the signal at the output 180º out of phase with the
input signal.
2.2
I/P switch
In the ‘Mic’ position, the unit takes the input signal
from the ‘Mic In’ XLR socket at the rear of the unit and
gives up to 79dB of gain to a mic level signal. When
set to ‘Line’ the unit takes the input signal from the
‘Line In’ XLR socket and gives up to 45.5dB of gain to
a line level signal.
2.3
DI socket
This socket provides an unbalanced, high impedance
input for any low or instrument level input sources.
This input will cut any other input when connected, so
it will become the input to The Rooster regardless of
the position of the I/P switch.
2.4
I/P Level control
The ‘I/P Level’ control gives continuously variable
adjustment over the input gain of The Rooster in
whatever mode it is being used.
2.5
Bass Lift control
The ‘bass lift’ control gives continuously variable
adjustment over the amount of bass boost applied to
the signal. The unique ‘vari slope’ bass lift curve can
be thought of as a ‘shelving’ type curve at low
amounts of boost. As the boost increases the low end
©Thermionic Culture Ltd., May 2008
4
‘tips up’, giving an emphasis to lower frequencies and
this adds an impression of size to the bass end.
2.6
Mid/Hi Lift control
The ‘Mid/Hi Lift’ control gives continuously variable
adjustment over the amount of mid or high frequency
boost applied to the signal. The ‘2.5k/4k/Hi’ switch,
described next, determines the actual frequency range
being lifted.
2.7
2.5k/4k/Hi switch
This switch provides the user with a very broad lift at
2.5 & 4kHz (highest peak frequencies) with some top
lift as well and a ‘vari slope’ shelving type curve on the
‘hi’ setting. At maximum boost the peak point for the
‘hi’ setting will be 10kHz.
2.8
Mid Cut control
The ‘mid cut’ control gives continuously variable
adjustment over the amount of mid range frequencies
being cut from the signal. The curve used is a bell
shape curve that becomes sharper as more cut is
applied. The centre of the curve is at 700Hz.
2.9
Bass Cut switch
The ‘Bass Cut’ switch is a stepped control with the
following options available :-
·
·
·
·
·
·
0 Flat response;
1 High pass filter operating below 30Hz;
2 6dB per octave curve, 3dB down at 120Hz;
3 6dB per octave curve, 3dB down at 350Hz;
4 Shelving curve, 3dB down at 800Hz;
5 Shelving curve, 3dB down at 3kHz
Positions 2-5 have a steeper cut below 30Hz.
©Thermionic Culture Ltd., May 2008
5
2.10 LPF switch
Switches a Low Pass Filter in or out of circuit after the
distortion valve. This is included because, in situations
where all stages of The Rooster are being pushed into
extreme distortion, it may be necessary to tame the
excessive high frequency content created by the
distortion itself. This control can provide a smoother
kind of extreme distortion to the signal. This filter starts
acting above 5kHz and is 6dB down at 10kHz.
2.11 Mode switch
This switch determines whether The Rooster’s 5725
valve is to be used as a Triode or Pentode valve.
Triode valves tend to give predominantly 2nd order
harmonic distortion when driven hard whereas
Pentode valves give predominantly more 3rd order
harmonics. 2nd order harmonics will tend to sound
smoother and 3rd order harmonics will give a more
aggressive effect.
2.12 Attitude switch
The ‘Attitude’ switch allows the user to determine how
much distortion, or THD The Rooster will add to the
signal. At position ‘1’ The Rooster is capable of
delivering a very clean signal (typically 0.01%), but as
the control is stepped towards ‘Max’ the distortion
provided by The Rooster will increase.
This does also rely on the setting of the ‘I/P Level’
control, which if turned down will decrease distortion
and when turned up increases distortion. With both
controls set to maximum the distortion will be very
extreme.
©Thermionic Culture Ltd., May 2008
6
2.13 O/P Level control
The ‘O/P Level’ control is a continuously variable
attenuator that controls the output level of The
Rooster. A cleaner signal is obtained when the control
is set to maximum. Turning the output control down
towards minimum and driving the input of The Rooster
harder results in more distortion.
2.14 Off/48V switch
The Off/48V switches located at the right hand side of
The Rooster, control whether or not the 48V phantom
power is applied to the ‘Mic In’ XLRs. This allows the
use of phantom powered microphones. Please
ensure that these are switched to the ‘Off’ position
when using ribbon microphones or passive
equalisers such as The Pullet.
2.15 Meters
The meters read the output level of The Rooster after
the ‘O/P Level’ control, serving as a basic indication of
the output level feeding the next piece of equipment in
the signal chain.
©Thermionic Culture Ltd., May 2008
7
3
Operational hints and tips
To use The Rooster as a clean, high quality, valve mic amp.
Set the ‘O/P Level’ control to maximum and the ‘Attitude’
switch to ‘1’, then use the ‘I/P Level’ control to obtain the
desired amount of gain. If more gain is required simply
increase the ‘Attitude’ switch until the gain is satisfactory.
This can still give acceptably clean results even with the
‘Attitude’ switch near to ‘Max’.
The ‘LPF’ filter becomes especially useful when heavily
distorting DI inputs, like bass instruments for example. As
the distortion becomes extreme the high frequency content
can start to sound more ‘clipped’ and stands out from the
actual sound of the instrument. Using the ‘LPF’ filter will
tame the problem frequencies and result in a smoother more
musical sounding distortion, allowing the user to push The
Rooster into even more distortion if desired.
The Rooster can act as a subtle enhancer on mixdown. For
example, a vocal sound can be given more life and cut
through a mix better if a little overdrive is added plus some
additional mid range or top EQ. Try the ‘Attitude’ switch at ‘4’
and add a little mid lift at 4k, the ‘Pentode’ setting will make
the vocal slightly more aggressive if required.
Drum microphones can benefit greatly from being recorded
through The Rooster. A mic that is placed to capture the
sound of the whole kit with a little room sound included
would be ideal. The ‘Attitude’ can be increased to give a
similar effect to compression. The ‘Bass Lift’ can also be
used to give a very large bottom end to the drums. The
‘Triode’ and ‘Pentode’ settings will govern how smooth or
harsh the user wants the overall effect to be.
©Thermionic Culture Ltd., May 2008
8
4
Connections
There are 3 XLR connections per channel at the rear of The
Rooster, plus one DI jack input per channel, on the front
panel.
‘Mic In’ is a balanced input, which all microphones should be
plugged into. The connector is a 3 pin female XLR. (The
input signal should be applied to pins 2 and 3. Pin 1 is
ground).
‘Line In’ is the female 3 pin XLR socket that any line level
signals (+4 dBV) should be sent to. These inputs are
balanced (see ‘Mic-In’ for connections). If an unbalanced
source is used, Pin2 should be signal and pins 1 and 3
should be ground.
‘O/P’ is the male 3 pin XLR socket that the line level output
signal (+4 dBV) appears at. On the standard Rooster, the
output is unbalanced (Pin 2 is the ‘hot’ output signal and pins
1 & 3 are ground). A balanced version is also available (pins
2 & 3 are the balanced signal out and pin 1 is ground).
‘DI’ is the jack socket on the unit’s front panel. This provides
a high impedance signal for all low level and instrument level
signals. When this input is connected it will disable all other
inputs on this channel and operate regardless of the position
of the ‘I/P’ switch.
©Thermionic Culture Ltd., May 2008
9
5
Servicing and maintenance
5.1
Valves
All valves are selected to ensure that the unit gives
optimum and consistent performance across both
channels.
Although Thermionic Culture Ltd. guarantees the
valves for twelve months, they can last up to 20 years.
Spare valves can be obtained from Thermionic Culture
Ltd.
The Rooster Valve complement is:
Input:
Distortion:
Output:
5.2
ECC81 / 12AT7 (2 off)
5725 (2 off)
PCF 80 (2 off)
Operating voltages / fuses
The Rooster can be set to operate from either 230V or
115V 50/60 Hz AC. The appropriate mains input
voltage can be selected on the red switch located next
to the mains inlet.
Note: Mains fuses must be replaced in accordance
with the following table.
230V
115V
©Thermionic Culture Ltd., May 2008
T315mA
T630mA
10
6
Specification
Measurements are made at typical ‘Attitude’ setting ‘2’. in
Pentode mode with an output of +4dBu. Load resistance is
10kΩ.
Available gain (dB)
Mic
Line
Frequency response
+0dB, -1dB
Distortion (THD @ 1kHz)
Noise (IEC weighted)
MOL (2% THD @1kHz)
Phase shift
Input impedance
Mic
Line
DI
Output impedance
48 (79 with Attitude at max
@1kHz)
14.5
7Hz to 45kHz
≤0.035%
≤95dB below MOL
≥+25dBu
22º (6%) at 10kHz (8º extra on
balanced version)
600Ω
10kΩ
47kΩ unbalanced
600Ω
The Rooster is designed to work into a load of at least 4x
output impedance. If loaded with 600Ω, the bandwidth and MOL
will be reduced.
©Thermionic Culture Ltd., May 2008
11
The Rooster - frequency response curves
20
2k5 lift(10)
Hi Lift(10)
4k lift(10)
Bass lift (10)
Bass lift (7)
Bass lift (3)
Bass cut (1)
Bass cut (2)
Bass cut (3)
Bass cut (4)
Bass cut (5)
Mid Cut(9)
Mid Cut (5)
LPF
Gain (dBu)
10
0
-10
-20
-30
0.02
0. 1
1
Frequency (kHz)
10
100
Thermionic Culture Ltd., Harlow, Essex, UK
Tel: +44 (0)1279 414770 Fax: +44 (0)1279 412233
www.thermionicculture.com
©Thermionic Culture Ltd., May 2008. Printed in UK.
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising