Comp-S (2015)
Installation Instructions
**CAUTION** - Take care when installing black ceramic coated exhaust system. The coating can be scratched when installing.
1.
Make sure the motorcycle is completely cool before starting the
installation. Make sure the bike is secure on the side stand or ideally
on a service lift.
6.
TBR mufflers are specific to front and rear cylinders and are marked
accordingly. Top (T), bottom (B).
2.
Loosen OEM joint clamps.
7.
Remove OEM joint clamp and install onto TBR inlet.
3.
Remove four muffler bolts. These will be used with the TBR mufflers.
8.
Install TBR Slip-Ons onto OEM head-pipe. We recommend installing
bottom muffler and stock hardware first. Tighten.
4.
5.
Remove OEM mufflers.
9.
Install top muffler and bolts. Tighten.
Slightly loosen header nuts at the cylinder. Loosen the two lower
bolts at transmission where the front header mount is. Pull headers
away from motorcycle enough to install spacer behind the mount.
Tighten these two bolts and header nuts after spacer is installed.
10.
Tighten joint clamps.
11.
Double check all your work.
12.
Before you run the bike, clean off all fingerprints and dirt, as any
oily residue will etch the metal and become somewhat permanent
when the system gets hot. Run the bike and enjoy. It is normal for
some white smoke to appear the first time you start the bike. This is
packing/manufacturing oil from inside the pipe burning off. Check
for gaps or leaks. If you find a leak, a little high temperature silicon
sealant should fix it. After 50 to 100 miles, recheck all fasteners for
tightness.
Harley Davidson
Softail Deluxe / Slim
Slip-On Exhaust System
Part # 005-4140499D/D-B
IMPORTANT - PLEASE READ CAREFULLY
We recommend that this performance part be installed by a qualified
motorcycle technician. If you have any doubts as to your ability to install this
performance part, please consult with your local motorcycle dealer. Read all
instructions first before starting installation. Make sure the motorcycle and
exhaust system are completely cool before starting the installation. Also,
make sure the bike is secure on a center stand or ideally a service lift during
installation. Be sure to save all stock components for possible use later.
Warranty
Two Brothers Racing products are intended for closed course competition purposes only, and therefore are sold “as is”
without warranty. Two Brothers Racing specifically disclaims any warranties of merchantability or fitness for a particular
purpose and disclaims all responsibility for consequential and incidental damages or any other losses arising from the use
of these products or parts.
Care & Cleaning
Care & Cleaning
Keep system free of dirt and moisture. Store in a cool, dry place. Make sure vehicle is
completely cool before maintenance.
Stainless Header System: Polished stainless steel pipes will turn a light golden hue after a few
heat cycles, this is a normal characteristic of high quality stainless steel. Clean using a mild water
based spray cleaner. Always apply cleaner or polish with a soft, clean cloth.
Titanium Header System: Polished titanium pipes will experience color shift ranging from deep
blue/purple through amber after a few heat cycles. This is a normal characteristic of high quality
titanium. Clean using a mild water based spray cleaner. Always apply cleaner or polish with a
soft, clean cloth.
Polished Aluminum Canisters: Use an aluminum or mag wheel polish to restore the bright
finish to factory spec.
Brushed Aluminum Canisters: Clean using a mild water based spray cleaner. Always apply
cleaner or polish with a soft, clean cloth.
Carbon Fiber Canisters: Clean using a mild water based spray cleaner. Always apply cleaner
or polish with a soft, clean cloth. Always make sure the fiberglass packing inside is in good
condition and not burned out, as exhaust heat inside an empty canister will deteriorate the
carbon fiber sleeve.
TBR sells repack kits (Road - #005-10038, Offroad - #005-10038MX) that include everything you
need to easily do it yourself.
Titanium Mufflers: For cleaning use a mild water based spray cleaner. Always apply cleaner
or polish with a soft, clean cloth. Always make sure the fiberglass packing inside is in good
condition and not burned out, as exhaust heat inside an empty canister will deteriorate the
carbon fiber sleeve.
TBR sells repack kits (Road - #005-10038, Offroad - #005-10038MX) that include everything you
need to easily do it yourself.
Repack all road canisters every 3,000 miles. Part #005-10038
Repack all offroad canisters after every 10 hours of use. Part #005-10038MX
NEVER dyno test your bike with carbon fiber or titanium canisters installed - the intense heat
and lack of cooling air can quickly burn through the canister material. Two Brothers Racing does
not provide a warranty for burned canisters.
Harley Davidson
Softail Deluxe Slim
Slip-On Exhaust System
Part # 005-4140499D/D-B
Qty. Description
Part Number
1
1
1
005-414-S
Softail Muffler - Top - 24”
Softail Muffler - Bottom - 24”
Spacer
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement