lih-020 rev3

lih-020 rev3
HANDLINE &
Maintenance and Service Procedure
For Nozzles with: Serial # TFT-H465101 and over or Manufactured after 12/01/2003
INTRODUCTION
TASK FORCE TIPS AUTOMATIC: The nozzle you have purchased is your
primary tool in the battle against fire. It has been manufactured with great
care to give you the finest performance possible. All components are of top
quality and extremely rugged. With regular inspection and attention it will
serve you for many years. This publication is intended for those who prefer
to perform service on their own equipment. Factory service is available and
encouraged, and in most cases, seldom exceeds 24 hours one day in our
facility. Factory serviced equipment is serviced by experienced workmen
and fully tested before being returned. Repair charges for non-warranty
items are usually minimal and all serviced equipment is promptly returned
functioning to original specifications. Task Force Tips assumes no liability,
expressed or implied for damage to equipment or injury to personnel that is
a result of user service. IMPORTANT: After any maintenance or service,
always check nozzle for proper operation per INSPECTION CHECKLIST
and flow characteristics in “MANUAL: HAND-HELD AUTOMATIC
NOZZLES” (LIN-030).
GENERAL INFORMATION
TOOLS REQUIRED
The following tools are required for general service to the nozzle:
3/32, 1/8, 7/32 and 5/16 Allen wrenches
Dow #112 Lube/sealant
Loctite #271 thread locking adhesive
oxyacetylene torch
razor knife
Additional tools needed to service the shaper are:
strap wrench
vise with padded jaws
Handline / Dual-Force shaper removal clamp
(special tool TFT #THM-502)
Additional tools needed to service the pressure control are:
dental pick
two small probes, approximately 3/32 dia (such as a drill bit)
drill press, 17 inch opening
THREADED JOINTS: have been secured using Loctite® #271 thread
locking adhesive. Disassembly requires a minimal application of heat with
an oxyacetylene torch to break the bond. The threads should be heated to
approximately 450 F. Excessive heat application will cause damage to
adjacent seals and labels. Replacement parts must be reinstalled using
Loctite® #271, or equivalent. Small vials of Loctite® #271 for field service
are available; order Part # V5010, (Loctite® #271 - Mini Dispenser).
LUBRICANTS: If parts are disassembled in an area where O-rings are
present, reassemble using DOW #112 Lube on all O-rings and surfaces
that the O-rings contact. Call Dow Corning® Corp. at 800-447-4700 for the
name of your nearest distributor. The lube is also available through TFT as
item number VSA-101. If the nozzle is not disassembled refer to Field
Lubrication Procedure Section (on back).
LABEL REPLACEMENT: If labels become damaged, remove old labels
with a razor knife. Remove adhesive with acetone or methyl ethyl ketone.
Surface must be clean, dry and free from grease. Carefully apply new label.
ORDERING PARTS: Always specify the serial number of the nozzle when
ordering parts. The serial number is found on the back of the nozzle next to
the coupling. Be sure to use complete DESCRIPTION and ORDER #, as
printed on parts list. All requests for couplings must specify thread size.
Pricing information will be given at time of order. Parts and Repair Kits may
be purchased on-line at www.tft.com
BACK END
COUPLING AND BASE SERVICE PROCEDURE
TOOLS REQUIRED
1/8, 5/16 Allen(hex) wrench
Loctite #271 thread locking adhesive
oxyacetylene torch
GENERAL: Occasional replacement of hose gaskets is recommended.
Replace GASKET GRABBER [13c or 3b] if severe impact has caused
damage. Coupling service kits which include all hardware and Loctite®
#271 are available for all standard 1.5” or 2.5” couplings. Special
configurations or model changes to a nozzle can be made by selecting the
desired coupling or base. Couplings with special or standard threads are
interchangeable and may be exchanged on new nozzles. Please specify
desired threads when ordering.
COUPLING AND BLITZ BASE REMOVAL: All couplings and blitz bases
are retained with a ball race and set screw. Heat and then remove the ¼”-28
SOCKET SET SCREW [5c, or 1b] from the coupling using a 1/8” Allen
wrench. Turn coupling so that hole faces down and rotate coupling back
and forth to allow 3/16" STAINLESS STEEL BALLS [4b, 15c or 5b] to drop
out. When all the balls are out of the groove, the coupling can be removed.
Remove GASKET GRABBER/ debris screen [13c, or 3b] from the coupling.
NOTE: On couplings [6c, 9c, 11c and 12c] and Base [2b], O-RING 141 [14c
and 4b] will be found adjacent to the GASKET GRABBER [13c, or 3b]. On
coupling [2c], O-RING 151 [3c] is used. Replace and grease the proper ORing before installing the coupling.
COUPLING AND BLITZ BASE INSTALLATION: Insert the GASKET
GRABBER/ debris screen [13c, or 3b] into the coupling, raised end pointing
toward the front of the nozzle. Put the coupling onto the mating part and
load the correct number of balls into the ball groove (SEE PARTS LIST ON
EXPLODED VIEW OF NOZZLE TO DETERMINE CORRECT NUMBER OF
STAINLESS STEEL BALLS [4c, 15b or 5b] FOR YOUR COUPLING).
Insertion of the balls is easier if the coupling is rotated slightly back and forth
as the balls are loaded. Apply Loctite® #271 and install proper ¼”-28
SOCKET SET SCREW [5c, or 1b]. The set screw should be flush with the
surface of the coupling. If the coupling is difficult to turn, or feels rough when
turned, the set screw is in too far. Back set screw off a turn or so and try
again. If the feel is still not correct, recheck the number of balls in the
coupling. On TIP ONLY COUPLINGS and BLITZ BASES run the screw into
the slot on the ball groove until it bottoms out without applying pressure.
TIP ONLY BASE SERVICE: The TIP ONLY BASE [8b] is attached to the TIP
ONLY BARREL ASSEMBLY [7f ] by a threaded joint which is retained by
Loctite® #271. Apply heat to the knurled rib nearest the front of the nozzle.
Damage to seals and labels can be reduced by protecting them with a wet
cloth. The TIP ONLY BASE [8b] can now be unscrewed. Remove and
replace O-RING 143 [9b]. Clean all threads, apply Loctite® #271 to threads
and screw together.
TWIST TYPE VALVE SERVICE PROCEDURE
STO SLEEVE SERVICE: To remove the STO SLEEVE [14b], first heat and
remove the CAM SCREWS [15b] and DETENT SCREWS [16b]. The detent
screws contain SPRINGS [18b] and BALLS [17b]. Then, STO SLEEVE
[14b] can be slid off. Service to interior STO valve should be done prior to
reinstalling STO sleeve. Inspect O-RINGS [19b] and replace if damaged.
Installation is reverse of removal. Before reassembly, grease O-Rings.
Clean screw threads and apply Loctite® #271.
STO VALVE SERVICE: Heat the back end of the STO BASE [20b] with a
torch and unscrew the STO TAIL PIECE [11b]. The STO SLIDER [13b] may
now be removed. Inspect and replace any damaged O-RINGS [9b, and
12b]. Grease O-Rings, clean threads and use Loctite® #271 upon
reassembly. Refer to SLIDE VALVE SERVICE PROCEDURE for Valve Plug
Replacement, Valve Shutoff Adjustment, and Valve Adjustment for Severe
Cold.
SLIDE VALVE SERVICE PROCEDURE
Tools Required:
3/32" Allen (hex) wrench
7/32" Allen (hex) wrench
5/16” Allen wrench Ball End
Flat Screw Driver
Mallet
DOW #112 Lube
LIH-020 February 22, 2007 Rev03
BOLT-ON PISTOL GRIP REMOVAL: PISTOL GRIP [19v] is held on by a
SOCKET HEAD CAP SCREW [21v]. Remove screw with a 5/16" Ball Driver
Allen wrench. To reinstall, clean thread and apply Loctite® #271. Tighten
screw to 95 in-lbs.
VALVE PLUG REPLACEMENT: After removing back end, VALVE PLUG
[17v, 10b, or 24b] is removed by pulling straight back. New valve plug can
be installed using a mallet.
VALVE SHUTOFF ADJUSTMENT: Shutoff valve is adjusted by the threads
between the valve body and the front end of the nozzle. While holding the
VALVE HANDLE [3v] against stops in the OFF position, screw front end into
the valve body until contact is made with the VALVE PLUG [17v]. Open
handle to ON position to remove contact. Screw the front end in 1/12 turn
further to give the valve shutoff compression. Thread in both SET SCREWS
[12v] until they bottom out, without applying pressure. In an alternating
fashion continue turning in set screws until tight.
VALVE ADJUSTMENT FOR SEVERE COLD: To help prevent hose line
freezing in cold climates, the valve may be adjusted for intentional leakage
by unscrewing the front end slightly. The valve may then be returned to
normal adjustment for complete shut off during warm weather as stated
above.
SLIDE VALVE DISASSEMBLY SEQUENCE
HANDLE REMOVAL: Remove both BUTTON HEAD CAP SCREWS [6v]
from VALVE HANDLE [3v] using a 7/32” Allen wrench. Slide CAM and
SAFETY PINS [4v and 5v] out of handle by gently prying about 3/8” apart
the handle and the valve body using a flat screw driver. To remove the
handle, pull upwards while containing the DETENT BALLS [7v] and
SPRINGS [8v] to prevent their loss. Service to interior valve parts should be
done prior to reinstalling handle.
SLIDER AND SEAL REMOVAL: Remove #10-32 x ¼” SOCKET SET
SCREWS [12v] from the VALVE ASSEMBLY [11v] using a 3/32" Allen
wrench. Unscrew front portion of nozzle from valve. SLIDER [15v] can now
be pulled out from the front of valve. Remove and inspect O-RINGS [13v,
14v and 16v]. Replace O-Rings if they are damaged.
SLIDE VALVE ASSEMBLY SEQUENCE
SLIDER AND SEAL INSTALLATION: Insert O-RINGS [13v, 14v and 16v]
into the proper grooves in the valve body. Check SLIDER [15v] for any
raised metal at groove area. Replace if necessary. Lubricate O-Rings and
slider with DOW #112 Lube. Push slider into the valve body.
HANDLE INSTALLATION: Insert DETENT SPRINGS [8v] and DETENT
BALLS [7v] into the handle lugs. While holding balls in place, snap the
HANDLE [3v] into place with offset holes FORWARD. Carefully align the
groove on SLIDER [15v] with offset hole in VALVE DISCS [9v] and with
offset hole in handle. Slide SAFETY PIN [5v] into offset hole in handle. Push
down into engagement with groove in slider, until head of pin is flush with
handle. Repeat procedure for CAM PIN [4v]. Insert BUTTON HEAD
SCREWS [6v] through the lower handle holes. Thread each into
corresponding center trunnion hole. Tighten HANDLE SCREWS [6v]
securely with a torque value of 100 in-lbs (11.3 N m). Handle should click
firmly and smoothly into all detent positions and the slider should move
back and forth smoothly. The force to move handle should be between 5 lbs
and 13 lbs applied at top center of handle.
BARREL CONE ASSEMBLY SERVICE: This assembly is permanent and
cannot be taken apart. Check to ensure that the flush spring is not
damaged by pushing down on the Barrel Cone with both hands (about 50
lbs force). The Barrel Cone Assembly should be replaced if the Barrel Cone
does not push down or spring back up by itself. Lightly grease the CAM
GROOVES before re-installing the SHAPER GUIDE.
SHAPER INSTALLATION: Install 336 O-RING [9f] in front groove of
SHAPER [10f]. Grease the seal and ball groove heavily. Place (48) 13/16”
ACETAL BALLS [8f] into greased ball groove. Apply Loctite® #271 to male
thread on SHAPER GUIDE [4f, or 5f]. Start shaper onto SHAPER GUIDE
threads. Place three SHAPER GUIDE BALLS [3f] into the grooves on barrel
and screw down shaper until threads bottom out.
PRESSURE CONTROL SERVICE PROCEDURE
Tools Required:
1/4 Allen wrench (10” Long)
1/4 Allen wrench (regular length)
Mallet
PRESSURE CONTROL REPLACEMENT: The pressure control may be
removed and replaced as a unit by following the procedure in the
PRESSURE CONTROL REMOVAL and INSTALLATION AND INITIAL
OPENING ADJUSTMENT sections.
NOTICE: The Pressure Control Unit is part of the BARREL ASSEMBLY [7f].
This unit is factory calibrated and sealed. Service on this unit is best
performed at the factory using special tooling and equipment. In the
unlikely event that this unit should need service, it is highly recommended
that you return the complete nozzle to the factory for repairs OR replace the
entire PRESSURE CONTROL UNIT. DO NOT ATTEMPT TO DISASSEMBLE
THE PRESSURE CONTROL UNIT! Task Force Tips will assume NO liability
for damage or injury resulting from attempts to disassemble or repair the
Pressure Control Unit.
PRESSURE CONTROL REMOVAL: Remove the shaft locking SCREW
[1p] with 10” Long ¼” Allen wrench. Insert the Allen wrench into the front of
the pressure control shaft and tap the wrench with the mallet, then unscrew
the unit out of the barrel assembly.
PRESSURE CONTROL INSTALLATION AND INITIAL OPENING
ADJUSTMENT: Apply grease to I.D. and O.D. of LOCKING SLEEVE [2p]
and threads of shaft locking SCREW [1p]. Place LOCKING SLEEVE with
hollow end forward onto the rear of shaft and then hand tighten the SCREW.
Screw the threaded end of pressure control shaft into barrel assembly. Set
the shaper to straight stream. Insert a ¼” Allen wrench into front of shaft
and turn in until baffle just touches BARREL CONE [7f] then turn back to
between ½ and ¾ of a turn (opening gap of .026/.036 inches or .66/.91 mm).
Keep Allen wrench in shaft to assure that shaft doesn't turn and tighten
screw to approximately 180 in-lbs.
IMPORTANT: Always flow test after adjusting. Nozzle pressure and flow
requirements are shown on the following table:
INITIAL OPENING at 40 PSI (2.8 BAR)
FLOW (MIN)
FLOW (MAX)
Opening Gap (REF)
38 GPM
(144L/MIN)
58 GPM
(204 L/MIN)
.026/.036in
(.66/.91mm)
NOZZLE PRESSURE NOZZLE PRESSURE
FRONT END
AT 95 GPM
AT 250 GPM
100 PSI MODEL
85 PSI +/- 6
99 PSI +/- 6
75 PSI MODEL
60 PSI +/- 6
80 PSI +/- 6
SHELL SERVICE PROCEDURE
SHAPER REMOVAL: The rubber bumper is permanently bonded onto the
stream shaper as a single unit referred to as the SHAPER [10f]. The shaper
is attached to the SHAPER GUIDE [4f, or 5f] by a threaded joint that is
retained by Loctite® #271. Grip rear portion of the nozzle in a vise with
padded jaws, or clamp SHAPER GUIDE [4f, or 5f] using TFT special tool
TH502 held in a vise. Direct a hot narrow flame around the rear portion of the
shaper and heat for approximately 20 seconds. Damage to BUMPER [10f]
and LABELS [1f, 2f, or 6f] can be reduced by protecting them with a wet
cloth. Use a strap wrench to unscrew the shaper from the shaper guide.
Remove the shaper. Inside the shaper are (48) 13/16” ACETAL BALLS [8f],
some of which may fall free as the Shaper is removed. If Shaper is to be
reused, clean ball track and replace 336 O-RING [9f] if damaged.
SERVICE TO CAM GROOVES AND BALLS: When Shaper is removed,
check to see if the stream shaping GUIDE BALLS [3f] and CAM GROOVES
[7f - part of BARREL CONE ASSEMBLY] are damaged. Replace Balls if
sheared or missing. If the CAM GROOVES are badly damaged, the
BARREL CONE ASSEMBLY should also be replaced.
DUAL-FORCE KNOB REMOVAL: To remove the DUAL-FORCE KNOB
[8p] from the BAFFLE [4p]:
1) Turn knob to standard setting.
2) Turn the SHAPER [10f] back to full flush.
3) Insert a small probe (such as a drill bit) into each of the two 7/64 holes on
the sides of the knob.
4) Simultaneously push in on each of the two probes (this disengages the
spring loaded pawls [6p] ) while turning knob clockwise (when viewed from
the front). Once knob turns a little, the probes may be removed.
5) Turn knob clockwise until it hits a stop. (about 25 degrees).
6) Pull knob to remove from baffle.
LIH-020 February 22, 2007 Rev03
DUAL-FORCE KNOB INSTALLATION:
1) Clean SPRING PLATE [6p] of any dirt or oil.
Attach label to this side
Spring plate
with label
2) Peel off backing and apply new LABEL [7p] to spring plate as shown in
Figure 1.
Pawl in this detent
3) Place spring plate with label attached into knob as shown in Figure 2.
4) Make sure that O-RINGS [5p] on baffle are in good condition. Apply
grease to O-Rings on baffle.
5) Place knob assembly from step 3 onto baffle. Make sure that notches on
spring plate are around the bosses on the baffle. Turn knob counterclockwise about 25 degrees to lock in place.
Align notches
6) Check for smooth operation between standard and emergency settings.
PROBLEMS:
If you have any questions or problems, please call for assistance.
Ears align with shallow
notch on spring plate
Attaching Label to Spring Plate
Back View of Dual-Force Knob
with Spring Plate Installed
FIGURE 1
FIGURE 2
(800) 348-2686 • (219) 462-6161 • FAX (219) 464-0620
TASK FORCE TIPS INC. - www.tft.com
2800 East Evans Avenue • Valparaiso, IN 46383-6940
EXPLODED VIEWS and PARTS LISTS
1c
5c
2c
3c
COUPLINGS
4c
2-1/2"
ROCKER LUG
5c
6c
To 2-1/2
BLITZ
BASE
ONLY
BRITISH
INSTANTAEOUS
7c
8c
5c
9c
STORZ
10c
5c
INDEX
1c
2c
3c
4c
5c
6c
7c
8c
9c
10c
11c
12c
13c
11c
1-1/2" FULL-TIME
ROCKER LUG
14c
15c
13c
1c
14c
5c
12c
2-1/2" LOCKOUT
ROCKER LUG
Eng_Drawings\h\Fin & SUB\New Handline\Exploded Views\COUPLINGS.DWG July 14, 2003 Rev. 0 DEK
DESCRIPTION
2.5" HOSE GASKET
2.5" ROCKER LUG COUPLING
O-RING-151
3/16 SS BALLS
1/4-28X3/8 SOCKET SET
2.5" BIC COUPLING
52 MM STORZ COUPLING
O-RING-134
2.0" BSP MALE SWIVEL
1.5" COUPLING GASKET
1.5" ROCKER LUG COUPLING
2.5" ROCKER LUG COUPLING
1.5" HARD GASKET GRABBER
SINGLE
DUAL FORCE
O-RING-141
3/16 SS BALLS
QTY
1
1
1
48
1
1
1
1
1
1
1
1
1
1
1
38
PART #
V31902
P197
VO-151
V2120
V1100
H687
H686
VO-134
H685
V3130
H694
P198
H730-60D
HD730-60D
VO-141
V2120
15c
To ALL BASE and
SLIDE VALVE PARTS
(except
2-1/2 Blitz Base)
LIH-020 February 22, 2007 Rev03
From 2-1/2
ROCKER LUG
1.5
”B
1b
2.5
”
LIT
Z
2b
BL
ITZ
3b
4b
From ALL
COUPLINGS
(except 2-1/2
ROCKER LUG)
5b
1b
6b
MO
D
EL
4b
5b
VP
G
7b
OPTIONAL
PLAYPIPE
PARTS
1b
MO
DE
L
MO
DE
4b
5b
T.O
.
8b
LS
.T.O
.
To
SLIDE
VALVE
PARTS
9b
15b
10b
11b
18b
9b
12b
13b
To
PISTOL GRIP
PART SET
(see Slide
Valve Parts)
21b
16b
22b
17b
23b
14b
To
FRONT
END
SHELL
19b
20b
Eng_Drawings\h\Fin & SUB\New Handline\Exploded Views\BASES-TO-STO.DWG
July 14, 2003 Rev. 0 DEK
23b
9b
BASES, TIP ONLY and TWIST TYPE
INDEX
1b
2b
3b
4b
5b
6b
7b
8b
9b
10b
11b
12b
DESCRIPTION
1/4-28 X 3/8 SOCKET SET SCREW
2.5" BLITZ BASE
1.5" HARD GASKET GRABBER
O-RING-141
3/16 SS BALLS
1.5" BLITZ BASE
PISTOL GRIP BODY - LONG
TIP ONLY BASE
O-RING-143
TIP ONLY PLUG
TAIL PIECE - STO
O-RING-132
QTY
1
1
1
1
1
37
1
1
1
2
1
1
1
PART #
VT25-28SS375
H675
H730-60D
HD730-60D
VO-141
V2120
H674
H692
H670
VO-143
HX591
HD662
VO-132
INDEX
13b
14b
15b
16b
17b
18b
19b
20b
21b
22b
23b
24b
24b
DESCRIPTION
QTY
SLIDER - STO
1
SLEEVE - STO
1
CAM SCREW
2
DETENT SCREW
2
3/16" TORLON BALL
2
DETENT SPRING - STO
2
QUAD-RING-039
2
BASE - STO
1
"OFF" LABEL - RED
1
"ON" LABEL - BLUE
1
10-32 X 1/4 SET SCREW-ND PATCH 2
VALVE PLUG - STO
1
PART #
HD660
HD668
HD780
HD785
V2120-TORLON
VM4200
VOQ-4039
HD665
HD755
HD750
VT10Y32SS250
HXD591
LIH-020 February 22, 2007 Rev03
PLAYPIPE HANDLE
1h
2h
3h
4h
From
BLITZ
BASES
INDEX
1h
2h
3h
4h
5h
DESCRIPTION
1/4-20 SS ACORN NUT
WASHER
1/4-20 X 2 STUD FULL THREAD
PLAYPIPE HANDLE
BLITZ BRACKET
QTY
8
8
4
2
4
PART #
VT25E20AC
VW500X265-63
VT25-20ST2.0
P220
H676
Eng_Drawings\h\Fin & SUB\New Handline\Exploded Views\PLTAYPIPE.DWG
July 14, 2003 Rev. 0 DEK
5h
To
SLIDE
VALVE
PARTS
SLIDE VALVE
1v
2v
3v
4v
6v
5v
8v
SERIAL NUMBER
7v
10v
From
COUPLINGS
BASES
9v
12v
13v
14v
INDEX
1v
2v
3v
4v
5v
6v
7v
8v
9v
10v
11v
12v
13v
14v
15v
16v
17v
18v
19v
20v
21v
DESCRIPTION
8-32 X 3/8 BH CAP SCREW
VALVE HANDLE COVER
VALVE HANDLE
CAM PIN
SAFETY PIN
3/8-24 X 3/4 BUTTON HEAD SCREW
DETENT BALL
DETENT SPRING
DISC
3/8-24 HEX JAM NUT
VALVE BODY
10-32 X 1/4 SET SCREW-ND PATCH
QUAD-RING 326
QUAD-RING 225
SLIDER
O-RING 143
VALVE PLUG
GRIP SPACER
PISTOL GRIP - BLACK
WASHER
3/8-16 X 1" SOCKET HEAD CAP SCREW
QTY
4
2
1
1
1
2
2
2
2
2
1
2
1
1
1
1
1
1
1
1
1
PART #
VT08-E32BH375
HM625-BLK
HX620
HX630
HX635
VT37E24BH750
VB234TO
HM770
HX640
VT37-24JNT
HX600
VT10Y32SS250
VOQ-4326
VOQ-4225
H660
VO-143
HX590
HM693-H
HM692-BLK
VM4901
VT37-16SH1.0
15v
To
LONG
GRIP
(VPG)
16v
11v
17v
18v
19v
To
FRONT
END
SHELL
20v
21v
Eng_Drawings\h\Fin & SUB\New Handline\Exploded Views\SLIDE-VALVE.DWG
July 14, 2003 Rev. 0 DEK
LIH-020 February 22, 2007 Rev03
SHELL FRONT END
Eng_Drawings\h\Fin & SUB\New Handline\Exploded Views\SHELL - FRONT END.DWG
July 14, 2003 Rev. 0 DEK
From
SLIDE VALVE
T.O. and
S.T.O.
INDEX DESCRIPTION
2f
NAME LABEL HANDLINE - 100 PSI
NAME LABEL HANDLINE - 75 PSI
NAME LABEL DUAL-FORCE 100/55 PSI
NAME LABEL DUAL-FORCE 75/45 PSI
3f
GUIDE BALLS
4f
SHAPER GUIDE
6f
BARREL LABEL - SINGLE PRESS
- DUAL-FORCE
7f
BARREL ASSEMBLY - HANDLINE
8f
3/16" BALLS
9f
O-RING 336
10f SHAPER WITH BUMPER
2f
4f
3f
QTY
1
1
1
1
3
1
1
1
1
48
1
1
PART #
HX745
HX745L
HXD745
HXD745L
VB334TO
HXD510
H740
HD740
HX850-KIT
V2115
VO-336
H500
6f
7f
8f
9f
10f
1p
From
FRONT
END
SHELL
2p
4p
To
PRESSURE
CONTROL
PARTS
5p
6p
3p
7p
8p
9p
For
SINGLE
PRESSURE
HANDLINE
For
DUAL-FORCE
PRESSURE CONTROL
INDEX
1p
2p
3p
4p
5p
6p
7p
8p
9p
DESCRIPTION
5/16-18 X 3/4 SOCKET HEAD CAP SCREW
LOCKING SLEEVE
PRESSURE CONTROL ASSEMBLY
SINGLE 100 PSI
SINGLE 75 PSI
PRESSURE CONTROL ASSEMBLY
DUAL FORCE 100/55 PSI
DUAL-FORCE 75/45 PSI
O-RING 005
SPRING PLATE
KNOB LABEL - 100 PSI STANDARD
KNOB LABEL - 75 PSI STANDARD/LOW
KNOB
KNOB PLUG
QTY
1
1
PART #
VT31-18SH750
HX571
1
1
HX840-KIT
HX840-75-KIT
1
1
2
1
1
1
1
1
HXD840-KIT
HXDL840-KIT
VO-005
HX555
HXD752
HXD752L
HXD560
VM4124
LIH-020 February 22, 2007 Rev03
DANGER
PERSONAL RESPONSIBILITY CODE
The member companies of FEMSA that provide emergency response
equipment and services want responders to know and understand the
following:
1. Firefighting and Emergency Response are inherently dangerous
activities requiring proper training in their hazards and the use of extreme
caution at all times.
2. It is your responsibility to read and understand any user's instructions,
including purpose and limitations, provided with any piece of equipment
you may be called upon to use.
3. It is your responsibility to know that you have been properly trained in
Firefighting and /or Emergency Response and in the use, precautions,
and care of any equipment you may be called upon to use.
4. It is your responsibility to be in proper physical condition and to maintain
the personal skill level required to operate any equipment you may be
called upon to use.
5. It is your responsibility to know that your equipment is in operable
condition and has been maintained in accordance with the
manufacturer’s instructions.
6. Failure to follow these guidelines may result in death, burns or other
severe injury.
FEMSA
Fire and Emergency Manufacturers and Services Association, Inc.
P.O. Box 147, Lynnfield, MA 01940 • www.FEMSA.org
LIH-020 February 22, 2007 Rev03
WARRANTY
Task Force Tips, Inc., 2800 East Evans Avenue, Valparaiso, Indiana 46383 ("TFT") warrants to the original purchaser of its
Ultimatic, Mid-Matic, and Handline series nozzles ("equipment"), and to anyone to whom it is transferred, that the equipment
shall be free from defects in material and workmanship during the five (5) year period from the date of purchase.
TFT's obligation under this warranty is specifically limited to replacing or repairing the equipment (or its parts) which are
shown by TFT's examination to be in a defective condition attributable to TFT. To qualify for this limited warranty, the claimant
must return the equipment to TFT, at 2800 East Evans Avenue, Valparaiso, Indiana 46383, within a reasonable time after
discovery of the defect. TFT will examine the equipment. If TFT determines that there is a defect attributable to it, TFT will
correct the problem within a reasonable time. If the equipment is covered by this limited warranty, TFT will assume the
expenses of repair.
If any defect attributable to TFT under this limited warranty cannot be reasonably cured by repair or replacement, TFT may
elect to refund the purchase price of the equipment, less reasonable depreciation, in complete discharge of its obligations
under this limited warranty. If TFT makes this election, claimant shall return the equipment to TFT free and clear of any liens
and encumbrances.
This is a limited warranty. The original purchaser of the equipment, any person to whom it is transferred, and any person who
is an intended or unintended beneficiary of the equipment, shall not be entitled to recover from TFT any consequential or
incidental damages for injury to person and/or property resulting from any defective equipment manufactured or assembled
by TFT. It is agreed and understood that the price stated for the equipment is in part consideration for limiting TFT's liability.
Some states do not allow the exclusion or limitation of incidental or consequential damages, so the above may not apply to
you.
TFT shall have no obligation under this limited warranty if the equipment is, or has been, misused or neglected (including
failure to provide reasonable maintenance) or if there have been accidents to the equipment or if it has been repaired or
altered by someone else.
THIS IS A LIMITED EXPRESS WARRANTY ONLY. TFT EXPRESSLY DISCLAIMS WITH RESPECT TO THE EQUIPMENT
ALL IMPLIED WARRANTIES OF MERCHANTABILITY AND ALL IMPLIED WARRANTIES OF FITNESS FOR A
PARTICULAR PURPOSE. THERE IS NO WARRANTY OF ANY NATURE MADE BY TFT BEYOND THAT STATED IN THIS
DOCUMENT.
This limited warranty gives you specific legal rights, and you may also have other rights which vary from state to state.
ANSWERS TO YOUR QUESTIONS
We appreciate the opportunity of serving you and making your job easier. If you have any problems or questions, our toll-free
"Hydraulics Hotline", 800-348-2686, is normally available to you 24 hours a day, 7 days a week.
Visit www.tft.com. Go to Literature, Service Procedures and then
Service Poster to view a full-size version of this booklet.
TASK FORCE TIPS, Inc.
Made in USA • www.tft.com
2800 E Evans Ave • Valparaiso , IN 46383-6940 USA
800-348-2686 • 219-462-6161 • Fax 219-464-7155
LIH-020 February 22, 2007 Rev03
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement