High Definition Digital
Video Wall LED Monitor
Operating Instructions
Model No.: CVW-47SDI2
Operation Instructions
Thank you for purchasing this product. For optimum performance and safety, please read these instructions carefully.
Before connecting, operating or adjusting this product, please read these instructions completely. Please keep this manual for future reference.
Table of Contents
1. Specifications ...................................................................1
2. Remote Control ................................................................2
3. Signal Input / Output Terminals ........................................2
4. Using Your LED Display ...................................................3
5. Using the OSD menu........................................................4
5.1 Picture Menu ..............................................................5
5.2 Setup Menu ................................................................5
6. RS-232 Protocol ...............................................................6
6.1 Piin Definition .............................................................6
6.2 Command ..................................................................6
7. Connection and Installation .............................................. 7
Disclaimers
The information in this manual has been carefully checked and is believed to be accurate. Cypress
Technology assumes no responsibility for any infringements of patents or other rights of third parties which may result from its use.
Cypress Technology assumes no responsibility for any inaccuracies that may be contained in this document. Cypress also makes no commitment to update or to keep current the information contained in this document.
Cypress Technology reserves the right to make improvements to this document and/or product at any time and without notice.
Copyright Notice
No part of this document may be reproduced, transmitted, transcribed, stored in a retrieval system, or any of its part translated into any language or computer file, in any form or by any means - electronic, mechanical, magnetic, optical, chemical, manual, or otherwise - without express written permission and consent from Cypress Technology.
© Copyright 2011 by Cypress Technology. All Rights Reserved.
Version 1.0 June 2011
Trademark Acknowledgments
All products or service names mentioned in this document may be trademarks of the companies with which they are associated.
Safety Precautions
Please read all instructions before attempting to unpack or install or operate this equipment, and before connecting the power supply.
Please keep the following in mind as you unpack and install this equipment:
Always follow basic safety precautions to reduce the risk of fire, electrical shock and injury to persons.
To prevent fire or shock hazard, do not expose the unit to rain, moisture or install this product near
water.
Never spill liquid of any kind on or into this product.
Never push an object of any kind into this product through module openings or empty slots, as you may damage parts.
Do not attach the power supply cabling to building surfaces.
Do not allow anything to rest on the power cabling or allow it to be abused by persons walking on it.
To protect the equipment from overheating, do not block the slots and openings in the module housing that provide ventilation.
Revision History
Version No
VR0
Date
20121114
Summary of Change
Preliminary Release
4
Important Information Warning
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION: TO REDUCE THE RISK OF ELECTRIC
SHOCK, DO NOT REMOVE SCREWS.
NO USER-SERVICEABLE PARTS
INSIDE.
REFER SERVICING TO QUALIFIED
SERVICE PERSONNEL.
The lightning flash with arrow-head within a triangle is intended to tell the use that parts inside the product are a risk of electric shock to persons.
The lightning flash with arrow-head within a triangle is intended to tell the use that parts inside the product are a risk of electric shock to persons.
Warning: To reduce the risk of fire or electric shock, do not expose this apparatus to rain or moisture. Do not place liquid containers (flower vase, cups, cosmetics, etc.) above the set
(including on shelves above, etc.).
1. Mains Supply
Operate this product only from the type of power supply from the package. If you are not sure of the type of power supplied to your home, consult your local power company.
Disconnect the product from the mains before your start any maintenance or installation procedures.
2. Overloading
Do not overload a wall outlet, extension cord or adapter as this may result in electric fire or shock.
3. Liquids
The product should not be exposed to any liquids such as dripping or splashing. In addition, no objects filled with liquids, such as vases, should be placed on the apparatus.
4. Cleaning
Disconnect the product from the wall outlet before cleaning. Please wipe the screen gently with soft cloth. Do not using chemical solvents to cleaning the product, e.g. methylbenzene, resin or alcohol, will damage the exterior case, tinted glass and the remote controller. Do not apply them to clean this machine.
5. Place
Do not place the product on an unstable, fluctuating or tilt table stand. The dropped display may endanger the personnel safety or product functions.
6. Cable
Do not intertwine, pull or compress the power cable when placing the product, otherwise the power cable or plug may be worn out and damaged. And do not presses the power cable beneath the product, otherwise electric shocks, short circuits or flash over may occur.
WWW.CYPRESS.COM.TW
4
1. Specifications
Model. No
SPECIFICATION
Screen Size (inches)
Aspect Ratio
Contrast Ratio
Viewing angle range
Panel Resolution
Response Time (ms)
Brightness
VIDEO
HDMI Compatibility
HDTV Compatibility
PC Resolution
SDI Timing & Distance
Progressive Scan
Video Noise Reduction
3D-Y/C Digital Comb Filter
Color Purity Optimizer
(3D Color Management)
Motion Pattern Noise Reduction
INPUT/OUTPUT
HDMI Interface
PC Input (for PC)
SDI
GENERAL
Power Supply
Power Consumption (W)
On Screen Display Languages
Dimension (H x V x D) mm
Package Dimension (H x V x D)mm
Net Weight (KG)
Gross Weight (KG)
Accessory
Power Cord
Remote Control with Batteries
User Manual
Warranty Card
CVWCVW-47SDI2
47
16:9
1400:1
178°
1366*768
12
800cd/M 2
480p/576p/720p/1080i/1080p
Up to 1080P
640x480@60,72,75
800x600@56,60,72,75
1024x768@60,70,75
1280x1024@60,75
1360x768@60
1920x1080@60
SD-SDI: SMPTE 259M-C, 270 Mbit/s up to 300m
HD-SDI: SMPTE292M, 1.485
&1.485/1.001 Gbit/s up to
200m
3G-SDI: SMPTE 424M/425M-AB,
2.970 & 2.970/1.001 Gbit/s up to 300m
Yes
Yes
Yes
Yes
Yes
2 rear
1 rear
2 rear (1 in, 1 out)
100V~240V
150
English
1046 x 591 x 115
1185 x 745 x 215
20.4
21
1
Yes
Yes
Yes
1
WWW.CYPRESS.COM.TW
WWW.CYPRESS.COM.TW
⑤
⑦
⑧
⑩
⑪
⑬
⑭
2. Remote Control
①
③
⑨
⑫
⑮
②
④
⑥
① POWER: Turn on the power of the monitor.
② POWER OFF: Turn off the power of the monitor.
③ SINGLE: Press this button to switch the output image to single display per monitor.
④ 2x2/3x3/4x4/5x5:Press thess buttons to switch the output image to 2x2/3x3/4x/3x2/4x3 or 5x5 displays per image.
⑤ ▲/▼: Adjust or select OSD menu up and down.
⑥ ◄/►: Adjust or select OSD menu left and right.
⑦ OK: Press this button to confirm the selection.
⑧ RETURN: Exit the OSD menu or the selection.
⑨ MENU: Display the OSD (On Screen Display) menu.
⑩ HDMI1/2: Press this hot key to switch the input to HDMI I/2.
⑪ VGA: Press this hot key to switch the input to VGA.
⑫ U/OVER: Press this key to adjust the screen when the image is underscan or overscan.
⑬ SDI: Press this hot key to switch the input to SDI.
⑭ OPTION: Press this key to switch to the special setting of the display image set by the factory design.
⑮ FAC:Press this key to enter into the factory mode. This is not a normal entry therefore, do not press this key unless it is adviced and guide by the special technician.
3. Signal Input/Output Terminals
2
⑦
① ② ③ ④ ⑤ ⑥
① AC IN: Connect the power cord with the power adaptor included in the package and plug it into the wall outlet for the power supply.
② HDMI IN 1/2: Connect the HDMI cable from DVD/Blu-ray player for signal input.
③ VGA IN: Connect the D-Sub 15pin cable from the PC/NB device or with RGB to D-Sub adaptor from the AV device for video signal input.
④ RS-232 IN: Connect the D-Sub 9pin cable from PC/NB device for RS-232 control.
⑤ RS-232 OUT: Connect the D-Sub 9pin cable to the next video/TV wall panel's(suggest using the same family type) RS-232 IN for unit signal distribution and displaying.
⑥ IR in: Connect the IR extender included in the package for receiving remote control's signal of the device.
⑦ SDI OUT: Connect the SDI cable to the next video/TV wall panel's(suggest using the same family type) SDI IN for unit signal distribution and displaying.
⑧ SDI IN: Connect the SDI cable from the SDI source equipment for signal input.
⑧
WWW.CYPRESS.COM.TW
2
4. Using Your LED Display
Refer to the owner's manual of any external equipment to be connected. When connecting any external equipment, do not connect any AC power cord to wall outlets until all other connections are completed.
1. Connect all AC power sources.
+
-
-
+
2. Installing the AAA size batteries in your remote control.
Step 1. Slide the back cover up to open the battery compartment of the remote control.
Step 2. Insert two AAA size batteries. Make sure to match the (+) and (-) ends of the batteries with the (+) and (-) ends indicated in the battery compartment.
Step 3. Slide the cover back into place.
Do not use caustic cleaners (Porcelain, stainless steel, toilet, or oven cleaner etc.) on the remote, as it may suffer damage.
3. Press the [POWER] button on the remote to turn on the LED Display.
Monitor
7M
30°
3M
30°
3M
Monitor
3
WWW.CYPRESS.COM.TW
WWW.CYPRESS.COM.TW
5. Using the OSD menu
Press [MENU].
Press [▲ / ▼] to highlight an option.
Press [OK] to confirm the selection.
5.1 Picture Menu
Press [▲ / ▼] to highlight an option.
Press [◄ / ►] to adjust.
Press [OK] to confirm the selection.
Press [RETURN] to exit menu.
4
Option
Picture Mode
Standard
Colour
Tint
Sharpness
Contrast
Brightness
Description
To adjust picture mode to: Vivid / Normal / Cinema / User
ON/OFF, when slelct to ON the system will go back to initial setup
To adjust the color saturation.
To adjust picture hue (NTSC only).
Sharpen of soften the picture.
To increase or decrease picture contrast.
To adjust for brighten or darken the picture.
WWW.CYPRESS.COM.TW
4
5.2 Setup Menu
Press [▲ / ▼] to highlight an option.
Press [◄ / ►] to adjust.
Press [OK] to confirm the selection.
Press [RETURN] to exit menu.
Option
Language
Standard
H Position Start
V Position Start
H Zoom Size
V Zoom Size
H Blanking Edit
V Blanking Edit
Description
Select the OSD display language (English, Traditional Chinese and Simplify Chinese).
Set it to ON will allow system to set the setup menu into the default value as indicated in the in the above diagram.
To set the total value of the horizontal value of the video/TV wall. This function is made to adjust for the standard monitor screen.
To set the total value of the vertical value of the video/TV wall. This function is made to adjust for the wide monitor screen.
To set the total value of the horizontal zoom in and zoo out size of the video/TV wall.
This function is made to enlarge the image or to shrink the image.
To set the total value of the vertical zoom in and zoo out size of the video/TV wall.
This function is made to enlarge the image or to shrink the image.
This function is to set the total value of the horizontal value of the banking area of the video/TV wall. This function is made to adjust the image according to display's frame.
This function is to set the total value of the vertical value of the banking area of the video/TV wall. This function is made to adjust the image according to display's frame.
Back Light
This function is to set the back light of the TV panel from the highest figure of
0 with the brightest light to the lowest figure of 230 with darkest light.
WWW.CYPRESS.COM.TW
WWW.CYPRESS.COM.TW
5
6
6. RS-232 Protocol
6.1 Pin Definition
RS-232 IN
Pin 1
Pin 2
Pin 3
Pin 4
Pin 5
Pin 6
NC
TxD
RxD
NC
GND
NC
Pin 7
Pin 8
Pin 9 NC
Baud Rate: 19200bps
Data bit: 8 bits
Parity: None
Stop Bit: 1 bit
Flow Control: None
RS-232 OUT
Pin 1
Pin 2
Pin 3
Pin 4
Pin 5
Pin 6
NC
RxD
TxD
NC
GND
NC
Pin 7
Pin 8
Pin 9 NC
6.2 Command
COMMAND
0x23 0x53 0x30 0x30 0x31 0x23
0x23 0x53 0x30 0x30 0x30 0x23
0x23 0x43 0x30 0x30 0x01 0x23
0x23 0x43 0x30 0x30 0x00 0x23
0x23 0x43 0x52 0x11 0x00 0x23
0x23 0x43 0x52 0x22 0x00 0x23
0x23 0x43 0x52 0x33 0x00 0x23
0x23 0x43 0x52 0x44 0x00 0x23
0x23 0x43 0x52 0x55 0x00 0x23
0x23 0x43 0x52 0x32 0x00 0x23
0x23 0x43 0x52 0x43 0x00 0x23
0xEF 0x05 0x00 0xC0 0x22 0xEE
0xEF 0x05 0x01 0xC0 0x22 0xEE
0xEF 0x05 0x03 0xC0 0x22 0xEE
0xEF 0x05 0x02 0xC0 0x22 0xEE
POWER ON
POWER OFF
UNDER SCAN
OVER SCAN
SINGLE
2x2
3x3
4x4
5x5
3x2
4x3
Change to HDMI 1
Change to HDMI 2
Change to PC
Change to SDI
ACTION
WWW.CYPRESS.COM.TW
6
7. Connection and Installation
①
④
FULL
②
③
2
①
④
SINGLE
②
③
SDI OUT
SDI IN
3
HDMI 1
HDMI 2
HDMI
SDI OUT
SDI IN
HDMI 1
HDMI 2
HDMI
1
4
HDMI 1
HDMI 2
HDMI
HDMI 1
HDMI 2
HDMI
PS3
CHDMI-4M
(HDMI Splitter)
SDI SECURITY CAMERA
SDI OUT
SDI IN
SDI OUT
SDI IN
POWER POWER OFF
2X2
3X2
SINGLE
3X3 4X4
4x3 5x5
FULL
OK
RETURN MENU
HDMI1/2 VGA U/OVER
SDI OPTION FAC
CR-107
7
WWW.CYPRESS.COM.TW
WWW.CYPRESS.COM.TW
A. Prepare the TV / Panel
Keep all the parts properly for future installation purpose.
1.Separate the fi xed rack from both side
* To avoid scratch or demage of the panel, it is suggested to place the panel on a fl at table that is soft pad.
* As show in the diagram 1, remove the screws (x4) from the fi xed rack (x2) of both side.
Fied Rack
Rack's Screw
Fied Rack
Rack's Screw
Diagram 1
As show in the picture is for reference only, please see the actual goods for standard.
2. Separate the support rack from the fi xed rack
* As show in the diagram 2, remove the support rack's screw (x4) from the fi xed rack (x2) of both side.
3. Fix the fi xed rack on
* Keep the support rack and all the removed screws properly for future installation purpose and fi x the fi xed rack on the
back of the panel as to diagram 3 show with the screws included in the panel's parts package.
Screws from panel's parts package
Fied Rack
Support Rack's screw
Screws from panel's parts package
Support Rack
Diagram 2 Diagram 3
4.Wall Mount Screws
* 4pcs of wall mount screews are the parts from the wall mount frame, put them on back of the panal with fl at
screwdriver as show in diagram 4.
Wall Mount
Screws
As show in the picture is for reference only, please see the actual goods for standard.
Diagram 4
MPM-CVW47SDI
