Advertisement
Advertisement
TEC Protable Printer
B-SP2D SERIES
Maintenance Manual
Document No. EO18-33014
Original
Mar., 2003
(Revised )
PRINTED IN JAPAN
(Revision Date: Feb. 17, 2004)
WARNING!
Follow all manual instructions. Failure to do so could create safety hazards such as fire or electrocution.
CAUTION!
The country setting for the Wireless LAN Module may need to be changed according to each country’s Radio Law. Before selling the printers, refer to Section 7 and change the setting if necessary.
NOTE:
Failure to follow manual instructions or any unauthorized modification, substitution or change to this product will void the limited product warranty.
EO18-33014
(Revision Date: Jan. 29, 2004)
TABLE OF CONTENTS
Page
1. UNPACKING ............................................................................................ 1- 1
1.1
PROCEDURE ................................................................................. 1- 1
1.2
CHECKS ......................................................................................... 1- 1
2. MAIN UNIT REPLACEMENT ................................................................... 2- 1
2.1
REPLACING THE CPU PC BOARD
AND THE WIRELESS LAN MODULE ............................................ 2- 1
2.2
REPLACING THE DRIVE PC BOARD
AND THE STEPPING MOTOR ASS'Y .......................................... 2- 5
2.3
REPLACING THE PLATEN ............................................................ 2- 8
2.4
REPLACING THE PRINT HEAD, CUTTER, AND SENSORS ....... 2-10
2.5
REPLACING THE STRIP ROLLER ............................................... 2-18
2.6
TEST PRINT .................................................................................. 2-20
2.7
SETTING AND ADJUSTMENT ...................................................... 2-24
3. ELECTRONICS ........................................................................................ 3- 1
3.1
BLOCK DIAGRAM .......................................................................... 3- 1
3.2
CPU PC BOARD ............................................................................. 3- 2
3.3
DRIVER PC BOARD ....................................................................... 3- 3
4. PROGRAM DOWNLOAD ......................................................................... 4- 1
4.1
PROGRAM DOWNLOADING TO A WINDOWS MACHINE ........... 4- 1
4.2
COMMUNICATION PARAMETERS SETTING ............................... 4- 3
4.3
DOWNLOAD TO THE PRINTER .................................................... 4- 4
4.4
DOWNLOAD TO THE WIRELESS LAN MODULE ........................ 4-10
5. TROUBLESHOOTING ............................................................................. 5- 1
6. OPTIONAL EQUIPMENT ......................................................................... 6- 1
6.1
HOW TO USE THE BATTERY CHARGER
(B-SP2D-CHG-QM) ....................................................................... 6- 1
6.2
HOW TO USE THE BATTERY CHARGER
(B-SP2D-CHG5-QM) ...................................................................... 6- 2
7. WIRELESS LAN PARAMETER SETTING ............................................... 7- 1
7.1
WHEN USING THE RFLAN CONFIGURATION TOOL .................. 7- 1
7.2
WHEN USING THE WEB BROWSER ........................................... 7-10
CAUTION!
1. This manual may not be copied in whole or in part without prior written permission of TOSHIBA TEC.
2. The contents of this manual may be changed without notification.
3. Please refer to your local Authorized Service representative with regard to any queries you may have in this manual.
Copyright © 2004 by TOSHIBA TEC CORPORATION
All Rights Reserved
570 Ohito, Ohito-cho, Tagata-gun, Shizuoka-ken, JAPAN
1. UNPACKING
1. UNPACKING
1.1 PROCEDURE
1) Open the carton.
2) Unpack the accessories from the carton.
3) Unpack the printer.
Owner's Manual
Accessory
(GH20 Type only)
SMW-3x8 Screw
Cord Clamp
Media Guide
SMW-3x8 Screw Belt Holder
EO18-33014
1.1 PROCEDURE
B-SP2D Printer
Outer Winded Guide
Battery
Owner's Manual
Battery Charger
(B-SP2D-CHG-QM)
Carton
Carton
[ Printer and Accessorry ]
[ Battery Charger ]
NOTES: 1. Keep the carton and pad for future transportation of the printer.
2. Since the power cord set is not enclosed in this battery charger unit, please purchase an approved one which meets the standard for each country from your Authorized TOSHIBA TEC representative.
For details, please refer to the B-SP2D-CHG Owner's Manual.
1.2 CHECKS
1) Check for damage or scratches on the machine.
2) Confirm that none of the accessories are missing.
1-1
2. MAIN UNIT REPLACEMENT
EO18-33014
(Revision Date: Mar. 10, 2006)
2.1 REPLACING THE CPU PC BOARD AND THE WIRELESS LAN MODULE
2. MAIN UNIT REPLACEMENT
WARNING!
1.
Unload the battery before replacing any parts.
2.
Danger of explosion if battery is incorrectly replaced. Replace the battery only with 'TOSHIBA TEC
Corporation, Battery Pack Type B-SP2D-BT, 7.4V 1400mAh Lithium-Ion. Discard used batteries according to the manufacture's instructions.
CAUTION!
1.
Since a lot of small molded parts are used in this printer, care must be taken not to damage or lose them.
2.
Be careful not to damage the print head while removing and reassembling.
3.
In the United States, used lithium ion batteries should be returned to the store where you bought the machine. (USA only)
4.
LITHIUM ION BATTERY
DISPOSE OF PROPERLY
Caution: Do not handle damaged or leaking lithium ion battery.
5.
Before handling the main parts, be sure to discharge static electricity in human body through other metals. Failure to do this may damage the CPU PC board, print head, etc..
Lubrication
CAUTION!
1.
Lubrication: During parts replacement
2.
Kinds of oil: FLOIL G-488: 1Kg can. (Part No.19454906001)
3.
Do not spray the inside of the printer with lubricants. Unsuitable oil can damage the mechanism.
All machines are generally delivered in their best condition. Efforts should be made to keep them that way. Lack of oil, or the presence of debris or dust, may cause an unexpected failure. To maintain in optimal operating condition, periodically clean the machine and apply the proper kinds of oil to each part in which lubrication is needed.
Although the frequency of lubrication varies according to how often the machine is used, as a minimum it is necessary to lubricate before any part becomes dry. It is also necessary to wipe off excessive oil or it will collect dirt.
NOTE: Replacement procedures are partly different depending on the models.
2.1 REPLACING THE CPU PC BOARD AND THE WIRELESS LAN MODULE
For GH20/GH30 models
1) Remove the three cover securing screws to remove the bottom cover. For the RoHS compliant printers, the cover securing screws are covered with rubber caps. First, remove the rubber caps using tweezers or something, and then, remove the cover securing screws. At this time, care must be taken not to damage the bottom cover.
The removed rubber caps are non-reusable. Please use new rubber caps (Part No.: 7FM02372000) when reassembling the printer.
NOTES: 1. When removing the bottom cover, support the gears so that they don't come out.
2. When reassembling, tighten the cover securing screws with 2.5 to 2.8kgf
⋅cm (0.245 to
0.275N
⋅m).
3. When reassembling, attach the bottom cover so as not to catch the FPC cable.
Bottom Cover
Cover Securing Screw
Rubber Cap
2-1
2. MAIN UNIT REPLACEMENT
EO18-33014
(Revision Date: Feb. 17, 2004)
2.1 REPLACING THE CPU PC BOARD AND THE WIRELESS LAN MODULE
For GH40 model
1) Remove the three PT-3x8 screws to remove the bottom cover.
Remove the wireless LAN module from the gear cover, and then, disconnect the FPC cable from the wireless
LAN module. Remove the three cover securing screws to remove the gear cover.
Gear Cover
Wireless LAN Module
Bottom Cover
FPC Cable
Cover Securing Screw
PT-3x8 Screw
NOTES: 1. When removing the gear cover, support the gears so that they do not come off.
2. When reassembling, tighten the PT-3x8 screws with 6kgf
• cm (58.8N
• cm).
3. When reassembling, be careful not to pinch the FPC cable by the bottom cover or gear cover.
Also, connect the FPC cable to the wireless LAN module with the terminal side facing to the bottom cover. Then, lock the FPC cable with the connector lock.
Wireless LAN Module
Connector
Terminal Side of the FPC Cable
4. When the wireless LAN module is replaced with a new one, it is necessary to set the country setting appropriately for the country where the printer is used. (Refer to Section 7.)
2-2
2. MAIN UNIT REPLACEMENT
EO18-33014
(Revision Date: Jan. 29, 2004)
2.1 REPLACING THE CPU PC BOARD AND THE WIRELESS LAN MODULE
2) Open the battery cover, and then remove the top cover.
NOTE:
When reassembling, attach the top cover so as not to catch the FPC cable.
Battery Cover
Top Cover
3) Disconnect all the connectors to remove the CPU PC board from the pritner.
NOTES: 1. When removing each FPC cable, unlock the connector with tweezers, etc. At this time, be careful not to scratch the FPC cable and the CPU PC board.
2. Do not fold back the FPC cables. Doing so may damage the internal wires.
CPU PC Board
CN103
Interface FPC
CN102
Sensor 1 FPC
CN101
Print Head FPC
CN104
Sensor 2 FPC
2-3
2. MAIN UNIT REPLACEMENT
EO18-33014
(Revision Date: Jan. 29, 2004)
2.1 REPLACING THE CPU PC BOARD AND THE WIRELESS LAN MODULE
4) While raising the CPU PC board a little, remove the Drive PC board from CN2 on the CPU PC board.
CN2 Drive PC Board
CPU PC Board
5) After replacing the CPU PC board with the new one, reassemble in the reverse order of removal.
After the replacement, perform each check and setting below.
(1) Status Indicator
Condition
The printer is off.
The printer is turned on.
Status Indicator
The status indicator is off.
The status indicator blinks in red for a few seconds, then lights in green.
If the battery is nearly end, the status indicator lights in orange. If the battery voltage is low, the status indicator lights in red.
The status indicator blinks in red.
After the printer is turned on, the
[FEED] button is pressed without media loaded.
When the status indicator doesn't perform as the table above shows, make sure that the cables are connected to the CPU PC board properly. If the status indicator still doesn't perform properly, replace the CPU PC board with the new one.
(2) Test Print
Perform a test print to check each item. (Refer to Section 2.6 TEST PRINT.)
(3) Initial Setting
With Set Up Tool, be sure to perform each sensor adjustment, destination setting, printer ID setting, and online check printing. (Refer to Section 2.7 SETTING AND ADJUSTMENT.)
2-4
2. MAIN UNIT REPLACEMENT
EO18-33014
(Revision Date: Jan. 29, 2004)
2.2 REPLACING THE DRIVE PC BOARD AND THE STEPPING MOTOR ASS'Y
2.2 REPLACING THE DRIVE PC BOARD AND THE STEPPING MOTOR ASS'Y
1) Remove the bottom cover, top cover, and CPU PC board from the printer. For the GH40 model, also remove the wireless LAN module and gear cover.
(Refer to Section 2.1 REPLACING THE CPU PC BOARD AND WIRELESS LAN MODULE.)
2) In case of the GH20 model, remove the SMW-2x6 screw to release the earth wire of the interface PC board
(RS-232C).
3) Release the connector lock to disconnect the FPC cable, and then pull out the interface PC board (Bluetooth or RS-232C).
4) Remove the gears from the printer in the following order; 1. motor idler gear, 2. idler gear, 3. platen idler gear.
(GH20 type only)
Earth Wire
SMW-2x6 Screw
Interface PC Board
(RS-232C)
Connector Lock
2. Idler Gear
FPC Cable
3. Platen Idler Gear
1. Motor Idler Gear
Interface PC Board (Bluetooth)
(GH30 model only)
5) Remove the 1. stepping motor ass'y, 2. ATC-battery terminal ass'y, and 3. drive PC board from the printer as an assembly.
6) Remove the stepping motor ass'y and the ATC-battery terminal ass'y from the drive PC board.
2. ATC-Battery Terminal Ass'y
3. Drive PC Board
1. Stepping Motor Ass'y
2-5
2. MAIN UNIT REPLACEMENT
EO18-33014
(Revision Date: Mar. 10, 2006)
2.2 REPLACING THE DRIVE PC BOARD AND THE STEPPING MOTOR ASS'Y
6) Remove the stepping motor ass'y and the ATC-battery terminal ass'y from the drive PC board.
7) Remove the two SMW-2x6 screws to remove the stepping motor from the motor bracket.
Stepping Motor
SMW-2x6 Screw
Motor Bracket
8) After replacing the drive PC board and the stepping motor ass'y with the new ones, reassemble in the reverse order of removal.
NOTES: 1. When reassembling the stepping motor ass'y, fit the positioning pins into the mounting hole of the motor bracket as the figure below shows.
2. For the GH20 model, when attaching the motor braket to the printer, make sure that the earth spring on the motor braket comes in contact with the printer's earth plate.
Positioning Pin
Earth Spring
Printer's Earth Plate
Positioning Pin Motor Bracket
2-6
2. MAIN UNIT REPLACEMENT
EO18-33014
(Revision Date: Jun. 13, 2003)
2.2 REPLACING THE DRIVE PC BOARD AND THE STEPPING MOTOR ASS'Y
3. Before reassembling the gears, wipe away dusts, stain or dirt on the gears with a clean cloth. Also apply FLOIL G-488 to each gear' shaft and the portion between the motor gear and the motor idler gear.
4. After reassembling the gears, manually rotate the gears to make sure that they works properly.
5. Make sure of the orientation of the gears, and then reassemble them in the following order; 1. platen idler gear, 2. motor idler gear, 3. idler gear.
3. Idler Gear
1. Platen Idler Gear
2. Motor Idler Gear
2-7
2. MAIN UNIT REPLACEMENT
EO18-33014
(Revision Date: Jan. 29, 2004)
2.3 REPLACING THE PLATEN
2.3 REPLACING THE PLATEN
1) Remove the bottom cover and the top cover from the printer. For the GH40 model, also remove the wireless LAN module and gear cover.
(Refer to Section 2.1 REPLACING THE CPU PC BOARD AND WIRELESS LAN MODULE.)
2) Remove the platen gear from the platen.
3) Remove the platen holders in the direction indicated by the arrows to remove the platen ass'y.
Platen Ass'y
Platen Holder
Platen Gear
4) Remove the platen shaft holders and the platen holders from the platen and the strip shaft.
Strip Shaft
Platen Holder
Platen Shaft Holder
2-8
Platen
2. MAIN UNIT REPLACEMENT
EO18-33014
2.3 REPLACING THE PLATEN
5) After replacing the platen with the new one, reassemble in the reverse order of removal.
NOTES: 1. Before reassembling the platen gear, wipe away dusts, stain or dirt on the gear with a clean cloth.
2. Make sure of the orientation of the platen gear, then reassemble is as the picture below shows.
[ Outer Side ]
Platen Gear
[ Inner Side ]
2-9
2. MAIN UNIT REPLACEMENT
EO18-33014
2.4 REPLACING THE PRINT HEAD, CUTTER, AND SENSORS
2.4 REPLACING THE PRINT HEAD, CUTTER, AND SENSORS
CAUTION!
1.
Before handling the print head, be sure to discharge static electricity in human body through other metals.
Failure to do this may damage the print head element.
2.
Never touch the print head element directly by hands or hard objects. Doing so will damage the element, causing a dot missing and a print failure.
1) Open the media cover.
2) Release the four hooks to remove the print head cover ass’y.
Print Head Cover Ass'y
Hook
3) Pull out the print head shaft.
2-10
Print Head Shaft
2. MAIN UNIT REPLACEMENT
EO18-33014
2.4 REPLACING THE PRINT HEAD, CUTTER, AND SENSORS
4) Remove the FPC harness from the head connector while being careful not to touch the print head element.
Head Connector
FPC Harness
5) Remove the SMW-2.6x6 screw to remove the print haed from the print head plate.
SMW-2.6x6 Screw
Print Head Print Head Plate
SMW-2.6x6
Screw
6) Release the two hooks which are provided at the inside of the media cover, and then remove the blind plate.
Blind Plate
Media Cover
Hook
2-11
2. MAIN UNIT REPLACEMENT
EO18-33014
(Revision Date: Jan. 29, 2004)
2.4 REPLACING THE PRINT HEAD, CUTTER, AND SENSORS
7) Remove the two SMW-2.6x6 screws to remove the cutter plate from the media cover.
Cutter Plate
Media Cover
SMW-2.6x6 Screw
Cutter Plate
8) When replacing the print head FPC, sensor 1 FPC, or sensor 2 FPC, follow Step 9 and after.
9) Remove the bottom cover, top cover, CPU PC board, drive PC board, stepping motor ass'y, and gears.
For the GH40 model, also remove the wireless LAN module and gear cover.
(Refer to Sections 2.1 REPLACING THE CPU PC BOARD AND WIRELESS LAN MODULE, 2.2 RE-
PLACING THE DRIVE PC BOARD AND THE STEPPING MOTOR ASS'Y, and 2.3 REPLACING THE
PLATEN.)
2-12
2. MAIN UNIT REPLACEMENT
EO18-33014
2.4 REPLACING THE PRINT HEAD, CUTTER, AND SENSORS
10) Pull out the media cover shaft, and then remove the media cover and the media guide.
Media Cover
Media Guide
Media Cover
Shaft
11) Remove the FPC of the sens 1 PC board ass'y from the frame.
Sens 1 PC Board Ass'y
Frame
(After performing Step 10 and Step 11)
Print Head Cover
Media Cover
Media Cover Shaft
Media Guide Frame
2-13
2. MAIN UNIT REPLACEMENT
EO18-33014
2.4 REPLACING THE PRINT HEAD, CUTTER, AND SENSORS
12) Remove the rivet, and then remove the sens 1 PC board ass'y from the print head cover.
Rivet Sens 1 PC Board Ass'y
13) Remove the print head FFC harness from the frame.
Print Head FFC Harness
14) Remove the dust sheet from the upper media cover switch.
Dust Sheet
Frame
2-14
Media Cover Switch
2. MAIN UNIT REPLACEMENT
EO18-33014
2.4 REPLACING THE PRINT HEAD, CUTTER, AND SENSORS
15) Remove the upper media cover switch, strip/batch sensor, and black mark/feed gap sensor , which are provided for the sens 2 PC board, from the frame.
Media Cover Switch
Frame
Strip/Batch Sensor
16) Remove the dust sheet from the lower media cover switch.
Sens 2 PC Board
Black Mark/Feed Gap Sensor
Dust Sheet
Media Cover Switch
2-15
2. MAIN UNIT REPLACEMENT
EO18-33014
2.4 REPLACING THE PRINT HEAD, CUTTER, AND SENSORS
17) Unhook the lower media cover switch, which are provided for the sens 2 PC board, from the frame.
Media Cover Switch
Frame
18) Remove the lower media cover switch with the sens 2 PC board from the frame.
Frame
Sens 2 PC Board
Media Cover Switch
19) After replacing the print head, cutter, and sensors with the new one, reassemble in the reverse order of removal.
NOTES: 1. Reassemble the cover springs properly when attaching the media cover shaft.
Cover Spring
Media Cover Shaft
2-16
2. MAIN UNIT REPLACEMENT
EO18-33014
2.4 REPLACING THE PRINT HEAD, CUTTER, AND SENSORS
2. After replacing the sensors, with the Set Up Tool, be sure to perform each sensor adjustment, destination setting, printer ID setting, and online check printing. (Refer to Section 2.7 SETTING AND
ADJUSTMENT.)
3. After replacing the media cover switch, perform a check by following steps below.
1) Turn on the printer and load a media roll.
2) Press the [FEED] button while sliding each of the media cover release catch.
3) Make sure that the printer works properly as the table below shows.
Condition
Media cover release catches are fully released.
Either of the media cover release catch is released.
Media cover release catches are locked.
Performance
The printer doesn't feed the paper.
The status indicator flashes in red.
The printer feeds the paper.
4) When the printer doesn't work properly, the media cover switch may not be attached properly or it may not be connected to the CPU PC board properly. Check these possible causes, then make sure of the printer's performance again. If the printer still doesn't work properly, replace the media cover switch with the new one.
2-17
2. MAIN UNIT REPLACEMENT
EO18-33014
2.5 REPLACING THE STRIP ROLLER
2.5 REPLACING THE STRIP ROLLER
1) Open the media cover.
2) Release the hooks to remove the strip cover to the direction indecated by the arrow.
Strip Cover
3) Remove the two strip support guides in the direction indicated by the arrows.
Strip Support Guide
4) Remove the strip roller together with the strip roller holders from the strip cover.
5) Remove the strip roller holders from the strip roller.
Strip Cover
Strip Roller Holder
2-18
Strip Roller
2. MAIN UNIT REPLACEMENT
EO18-33014
2.5 REPLACING THE STRIP ROLLER
6) After replacing the strip roller with the new one, reassemble in the reverse order of removal.
NOTES:
1.
When reassembling, fit the strip roller holders to the strip roller so that their wider sides contact the strip roller springs.
Strip Roller
Strip Roller Holder
2.
When reassembling, attach the strip support guides correctly as the picture below shows.
Strip Support Guide
2-19
2. MAIN UNIT REPLACEMENT
EO18-33014
(Revision Dtae: Mar. 10, 2006)
2.6 TEST PRINT
2.6 TEST PRINT
After replacing the print head ass’y, sensor ass’y or CPU PC board ass'y, perform a test print to check the print condition.
Procedure
1) Load a receipt roll (Type: PD-190R or equivalent, Paper roll diameter:
∅36mm) and the battery into the printer.
2) Turn on the printer while pressing and holding the [FEED] button.
3) The printer will automatically print the self diagnosis result.
4) Pressing the [FEED] button again causes the printer to print oblique patterns.
(Print sample)
1st label
2 Software version
5
6
7
1
2
3
4
8
9
B-SP2D
7FM00434001
MAIN V1.0 :xx00
10MAR2003
BOOT V1.0 :xx00
10MAR2003
FONT xx00
KANJI xx00
SENS R:4.3V
T:1.2V
P:1.0V
H:+30
°C
A:+24
°C
PEEL 3.2V
TYPE QM
ID 01234
HEAD OK (2)
BATT 8.2V (5)
ADJ.
+00 +0.0mm
P/W 120min
FORM 0000000000
0000000000
MODE LABEL
PARA [PC850][0]
LOOP IR:OK BT:OK
IrDA IrCOMM
FRONT
OP.
Bluetooth
0001cc400020
10
11
12
13
14
15
20
16
17
18
19
2nd and subsequent labels
1234567890123456789012345678901
1234567890123456789012345678901
1234567890123456789012345678901
1234567890123456789012345678901
1234567890123456789012345678901
1234567890123456789012345678901
1234567890123456789012345678901
1234567890123456789012345678901
1234567890123456789012345678901
1234567890123456789012345678901
1234567890123456789012345678901
1234567890123456789012345678901
1234567890123456789012345678901
1234567890123456789012345678901
1234567890123456789012345678901
1234567890123456789012345678901
1234567890123456789012345678901
1234567890123456789012345678901
1234567890123456789012345678901
1234567890123456789012345678901
1234567890123456789012345678901
1234567890123456789012345678901
1234567890123456789012345678901
1234567890123456789012345678901
1234567890123456789012345678901
1234567890123456789012345678901
1234567890123456789012345678901
1234567890123456789012345678901
1 Model name
B-SP2D
Model name
2 Firmware Part Number
7FM00434001
Software Number
NOTE:
For the RoHS compliant printers (Firmware version V1.8 or greater), this part number is not printed.
3 Checksum (MAIN)
MAIN V1.0
:xx00 10MAR2003
Date of issue
Checksum
Version
4 Checksum (BOOT)
BOOT V1.0
:xx00 10MAR2003
Date of issue
Checksum
Version
2-20
2. MAIN UNIT REPLACEMENT
EO18-33014
2.6 TEST PRINT
5 Checksum (FONT)
FONT xx00
Checksum for the C/G area
6 Checksum (Writable character)
KANJI xx00
Checksum for the writable character area
NOTE: Chinese character will be printed when supported by the printer.
7 Sensor status
SENS R:4.3V
T:1.2V
P:1.0V
H:+30
°
C
A:+24
°
C
Black mark sensor status
Feed gap sensor status
Strip/Batch
Thermistor status
Print head termistor status
NOTE:
Make sure that each sensor's voltage satifsies the standard below. If the voltage doesn't satisfy it, this sensor may be damaged. In this case, perform a sensor adjustment or replace it with the new one. (For the sensor adjustment, refer to Section 2.7 SETTING AND
ADJUSTMENT.)
R: 3.5V or more, T: 1.5V or more, P: 3.5V or more
H: (t-5) ~ (t+20)
°
C t = Environmental temperature
A: (t-5) ~ (t+5)
°
C
8 Threshold
PEEL 3.2V
Threshold voltage of strip sensor
9 Destination code
TYPE QM
Destination code
10 Printer ID No.
ID 01234
Printer ID No.
11 Print head element check
HEAD OK (2)
Print head output dividing method
(AUTO, 2, 3, AUTO 1)
Check result of the print head broken element
(OK: Normal, NG: Broken element)
NOTE:
When the check result is NG, the print head element may be broken. In this case, replace the print head with the new one.
12 Battery status
BATT 8.2V
(5)
5 levels of the remaining battery voltage
Remaining battery voltage
NOTE:
Using a battery fully charged, make sure that the remaining voltage is 7.6V to 8.4V. If is is less than 7.6V, a battery failure may occur. In this case, replace the battery with the new one.
2-21
2. MAIN UNIT REPLACEMENT
EO18-33014
(Revision Date: Jan. 29, 2004)
2.6 TEST PRINT
13 Print tone & Print start position
ADJ.
+00
+0.0mm
Print tone fine adjustment
Print position fine adjustment
NOTE: Setting value for the Print Position Fine Adjustment
When the setting value is x.3 mm, the value will be automatically changed to x.2 mm. In the same way, x.8 mm will be changed to x.7 mm. This is because the print head's dot density is 8 dots/mm.
14 Auto power off
P/W 120min
Auto power off (1min, 5min, 30min, 120min)
15 Versions of the forms No.1 to No.20
FORM 0000000000
0000000000
Versions of the form No.10 (top) and No.20 (bottom)
Versions of the form No.9 (top) and No.19 (bottom)
Versions of the form No.8 (top) and No.18 (bottom)
Versions of the form No.7 (top) and No.17 (bottom)
Versions of the form No.6 (top) and No.16 (bottom)
Versions of the form No.5 (top) and No.15 (bottom)
Versions of the form No.4 (top) and No.14 (bottom)
Versions of the form No.3 (top) and No.13 (bottom)
Versions of the form No.2 (top) and No.12 (bottom)
Versions of the form No.1 (top) and No.11 (bottom)
16 Print mode
MODE LABEL
Print mode (LABEL, RECEIPT, RECEIPT1, TPCL-LE)
17 Printer parameter
PARA [PC850] [0]
Without zero slash
Character code
2-22
2. MAIN UNIT REPLACEMENT
EO18-33014
(Revision Date: Jan. 29, 2004)
2.6 TEST PRINT
18 Loopback test
LOOP IR:OK BT:OK
Check result of the option device interface
(RS=RS-232C, BT=Bluetooth, LN=Wireless LAN) (OK, NG)
Check result of IrDA (OK, NG)
NOTE: The check result of RS-232C interface will be NG because a special jig is used.
RS-232C Loopback Connector Wiring Pattern
Connector Manufacturer: HIRAKAWA HEWTECH CORP.
Connector Type: VM2059 or equivalent
19 Baud rate & Protocol
IrDA IrCOMM 115,200 FRONT
Direction of IrDA (UPPER, FRONT)
Baud rate (TEC only)
(9,600, 19,200, 38,400, 115,200)
Protocol (TEC, IrCOMM)
20 Option interface
OP.
Bluetooth
Interface to option devices (RS-232C, Bluetooth, Wireless LAN)
9,600 EVEN
0001cc400020
Parity (RS-232C only) (EVEN, NON)
Baud rate (RS-232C only) (9,600, 19,200, 38,400, 115,200)
BD address (Bluetooth only) or MAC address (Wireless LAN only)
2-23
2. MAIN UNIT REPLACEMENT
EO18-33014
2.7 SETTING AND ADJUSTMENT
2.7 SETTING AND ADJUSTMENT
After replacing the CPU PC board or sensors, be sure to perform each setting and sensor adjustment with Set Up
Tool. According to your condition, perform a proper setting and adjustment as shown below.
When the CPU PC board was replaced with the new one
1) Install the Set Up Tool on a PC. (Refer to Section 2.7.2 Set Up Tool.)
2) Perform a sensor adjustment. (Refer to Section 2.7.3 Adjusting Sensors.)
3) Register a destination. (Refer to Section 2.7.4 Registering Destination.)
4) Register the printer ID. (Refer to Section 2.7.5 Registering Printer ID.)
5) Perform an online check printing. (Refer to Section 2.7.6 Performing Online Check Printing.)
When a sensor replacement or a sensor adjustment was performed
(in this case the CPU PC board is not replaced)
1) Perform a test print. (Refer to Section 2.6 TEST PRINT.)
Make sure that the paper type is set to LABEL mode. (Refer to Section 2.7.1 Selecting Paper Type.)
2) Install the Set Up Tool on a PC. (Refer to Section 2.7.2 Set Up Tool.)
3) Register a destination. (Refer to Section 2.7.4 Registering Destination.)
Select "IrDA:TEC Protocol" for F1:Transmission Cotrol, "Japan" for F2:Destination, respectively.
4) Perform a sensor adjustment. (Refer to Section 2.7.3 Adjusting Sensors.)
5) Register a destination. (Refer to Section 2.7.4 Registering Destination.)
Restore F1:Transmission Control to "IrDA:IrCOMM", "RS-232C", or "Bluetooth" and F2:Destination to
"Other countries" as printed on the test print performed in Step 1.
6) Perform an online check printing. (Refer to Section 2.7.6 Performing Online Check Printing.)
2-24
2. MAIN UNIT REPLACEMENT
EO18-33014
2.7 SETTING AND ADJUSTMENT
2.7.1 Selecting Paper Type
Type of paper to be issued can be selected on the printer. Select LABEL mode by following procedures below.
2-25
2. MAIN UNIT REPLACEMENT
EO18-33014
2.7 SETTING AND ADJUSTMENT
2.7.2 Set Up Tool
This software has the functions to adjust the sensors, set the destination, register the printer ID, and print the result of the online check. To perform any operations, face the B-SP2D’s IrDA window to the IrDA jig (Actisys
IR) connected to a PC through the serial interface.
The IrDA jig shown below is recommended. Please procure it locally.
Name: ACT-IR220L PLUS PC Serial IrDA Adaper
Manufacturer: ACTISYS
For details, please access to ACTISYS's homepage
http://www.actisys.com
Installing Software
To perform the above functions, the software “B-SP2D Series Production Process for Windows” must be installed on a PC.
When you need the above software, please contact TOSHIBA TEC Subsidiaries or our Sales Department.
[System Requirements]
System
IBM compatible PC running Windows 95
®
, Windows 98
®
, or Windows 2000
®
(Performance of PC running other OS is not guaranteed.)
NOTE: Windows 95, Windows 98, and Windows 2000 are registered trademarks of Microsoft Corporation.
Installed memory of 16MB minimum (32MB or more is recommended.)
Available hard disk space of 10MB minimum (10MB or more is recommended.)
Interface
For IrDA communication, the IrDA interface should be provided for the PC (without drivers such as
IrLAP) or an IrDA device which is connectable to a serial port should be provided for the PC.
For RS-232C communication, more than one serial port should be provided for the PC.
[Setup disk]
The SETUP DISK for installation consists of 2 floppy disks (3.5", 2HD, 1.44 MB).
B-SP2D Series
Production Process for Windows (V1.0.0)
WR.FD-SP2D-KOUTEI
DISK(1/2)
7FM00477000
7th March 2003
V001.000
Copyright
2003
TOSHIBA TEC CORPORATION
All Rights Reserved
1. While running Windows 98 (or Windows 95, Windows 2000), insert Setup Disk (1/3) into the PC floppydrive.
2. Click on the [START] button then highlight RUN and click on RUN.
3. When the RUN display appears, type in A:\SETUP.EXE and click on the [OK].
4. By following the messages on the screen, perform the installation.
5. When the installation was completed successfully, the end screen appears. Click on the [Finish] button to end the installation.
2-26
2. MAIN UNIT REPLACEMENT
EO18-33014
(Revision Date: Jan. 29, 2004)
2.7 SETTING AND ADJUSTMENT
2.7.3 Adjusting Sensors
This function is provided for adjusting printer’s sensors (Reflective, Transmissive, Strip, and No paper level).
The sensors have been optimally adjusted before shipment from the factory. Therefore, the sensors should not be adjusted, except when there is a need to adjust them. If the sensors are adjusted, be sure to follow the procedure described below, or the printer will not operate properly. The interface to be used for adjusting sensors, should be “IrDA: TEC Protocol”.
* “IrDA: IrCOMM” is not supported for the sensor adjustments. If the sensors have to be adjusted when the destination “Other countries” has already been registered, set “F1: Transmission Control” and “F2: Destination” to “IrDA: IrCOMM” and “Japan”, respectively and register them. Then, adjust the sensors.
When using the keyboard, press the [F1] or [F2] key together with the [Ctrl] key.
* To increase efficiency, until when the printer is turned OFF from when reading the sensor A/D values and each sensor adjustment are performed, a feed is not performed when the cover is closed.
1) Reading sensor A/D values
Connect the IrDA jig (Actisys IR) to the serial port on a PC, then start up the software for production process.
Turn the printer ON, then face the IrDA jig to the upper IrDA windows of the printer.
Press the [F3] key of the keyboard or click on the [F3: All sensors] button on the screen.
All of the current sensor A/D values will be read at once and displayed.
2-27
2. MAIN UNIT REPLACEMENT
EO18-33014
(Revision Date: Jan. 29, 2004)
2.7 SETTING AND ADJUSTMENT
2) Adjusting reflective sensor
Place the label part of the specified paper on the reflective sensor, then press the [F4] key of the keyboard, or click on the [F4: Reflective sensor] button on the screen. The reflective sensor will be adjusted. When the adjustment is completed, all of the current sensor A/D values will be displayed.
NOTE: If the adjustment value of the reflective sensor is out of the judgement criterion, an error message will appear. When clicking on the OK button of the error message window, the A/D values will be displayed. In this case, however, an "Error" is shown in place of the A/D value for the reflective sensor. Readjust the reflective sensor.
3) Adjusting transmissive/strip sensors
Remove labels from the backing paper of the specified paper, then place only the backing paper on the transmissive sensor. Pass the backing paper through the path for the strip issues.
Press the [F5] key of the keyboard, or click on the [F5: Transmissive/Strip sensor] button on the screen.
The transmissive and strip sensors will be adjusted. When the adjustments are completed, all of the current sensor A/D values will be displayed.
NOTE: If the adjustment values of the transmissive/strip sensors are out of the judgement criterion, an error message will appear. When clicking on the OK button of the error message window, the
A/D values will be displayed. In this case, however, an "Error" is shown in place of the A/D values for the transmissive and strip sensors. Readjust these sensors.
2-28
2. MAIN UNIT REPLACEMENT
EO18-33014
(Revision Date: Jan. 29, 2004)
2.7 SETTING AND ADJUSTMENT
4) Adjusting no paper level
Without placing the paper in the printer, press the [F6] key of the keyboard, or click on the [F6: No paper
level] button on the screen. The no paper levels for the reflective and the transmissive sensors will be adjusted. When the adjustments are completed, all of the current sensor A/D values will be displayed.
NOTE: If the adjustment values of the no paper level of the reflective and transmissive sensors are out of the judgement criterion, an error message will appear. When clicking on the OK button of the error message window, the A/D values will be displayed. In this case, however, an "Error" is shown in place of the A/D values for the reflective and transmissive sensor of no paper level. Readjust these sensors.
2.7.4 Registering Destination
While holding down the [FEED] switch on the printer, turn the printer ON. After the printer is initialized (LED blinks in red), the LED will blink in green for several seconds, then printer prints the self-test result.
To register the destination, face the IrDA jig (Actisys IR) to the upper IrDA window of the printer in this state, then press the [F10] key of the keyboard, or click on the [F10: Registration] button on the screen.
The destination will be registered. When the destination registration is normally completed, the message “The destination has been registered.” will be displayed. The interface to be used for registering the destination, should be “IrDA: TEC Protocol”.
2-29
2. MAIN UNIT REPLACEMENT
EO18-33014
(Revision Date: Jan. 29, 2004)
2.7 SETTING AND ADJUSTMENT
* When the destination is registered, the IrDA window of the printer will change from the upper window to the front window.
* The appropriate communications protocol for each destination is as follows:
• Japan: IrDA: TEC Protocol
• Other countries: IrDA: IrCOMM
NOTES: 1. When “Other countries” is mistakenly registered, change the [F1: Transmission Control] and
[F2: Destination] to “IrDA: IrCOMM” and “Japan”, respectively, then register them.
2. “IrDA: IrCOMM” is not supported for the sensor adjustments. If the sensors have to be adjusted when the destination “Other countries” has already been registered, set “F1: Transmission Control” and “F2: Destination” to “IrDA: IrCOMM” and “Japan”, respectively, and register them. Then, adjust the sensors. After all sensors are adjusted, change the destination to “Other countries” again.
When using the keyboard, press the [F1] or [F2] key together with the [Ctrl] key.
2.7.5 Registering Printer ID
Move the cursor to the printer ID entry box by pressing the [F7] key of the printer. Manually input the lower 6 digits of the printer’s serial number in the [F7: Printer ID] entry box. Or, click on the [Scanner] button on the screen and scan the printer ID with a scanner.
Turn the printer ON, face the IrDA jig (Actisys IR) to the front IrDA window of the printer, then press the [F8] key of the keyboard, or click on the [F8: ID Registration] button on the screen. The printer ID will be registered.
When the printer ID registration is normally completed, the message “The printer ID has been changed to xxxxx.” will be displayed. The interface to be used for registering the printer ID, should be “IrDA: TEC Protocol” and
“IrDA: IrCOMM” for Japan” and “Other countries” of the destination, respectively. Set the COM port number, also.
NOTES:
1. The printer ID is from 0 to 65535. If any value over this range is input, an error message will be displayed.
2. COM Port number can be set in a range from COM1 to COM9.
2-30
2. MAIN UNIT REPLACEMENT
EO18-33014
(Revision Date: Jan. 29, 2004)
2.7 SETTING AND ADJUSTMENT
2.7.6 Performing Online Check Printing
To print the online check result, select either of the following interfaces, according to the destination.
• IrDA: TEC Protocol: When “Japan” has been registered as the destination.
• IrDA: IrCOMM: When “Other countries” has been registered as the destination.
Select the appropriate option in [F1: Transmission Control].
(1) Load the paper on the path for the batch issues, then press the [Shift] + [F11] keys of the keyboard. Or, check the "Batch mode" check box and click on the [F11: Print] button on the screen. This operation results that the three labels are issued in the order of slant line (print tone fine adjustment value -10), test print (print tone fine adjustment value -10), and test print (print tone fine adjustment value +00).
(2) Load the paper on the path for the strip issues, then press the [F11] key of the keyboard. Or,check the
"Strip mode" check box and click on the [F11: Print] button on the screen. One label will be printed.
2-31
2. MAIN UNIT REPLACEMENT
(3) Make sure of printing on the labels and print positions.
(1)
(2)
EO18-33014
(Revision Date: Jan. 29, 2004)
2.7 SETTING AND ADJUSTMENT
Batch: 111-11
Strip: 999-99
Print tone
+00 or -10
Judgment criteria of (1): (Horizontal scanning direction)
Distance from the left edge of the label to the left edge of the printed rectangle: [4.5 ± 1 mm]
Judgment criteria of (2): (Vertical scanning direction)
Distance from the top edge of the label to the top edge of the printed rectangle: [8.0 ± 1 mm]
4) Self-Test Result Printing
B-SP2D-GH20-QM B-SP2D-GH30-QM
B-SP2D-GH40-QM
2-32
2. MAIN UNIT REPLACEMENT
EO18-33014
2.7 SETTING AND ADJUSTMENT
* Details of checked contents are as described in Section 2.6 TEST PRINT. Especially, the destination
(“TYPE” on the printouts) must be correctly set. Loop back check (“LOOP” on the printouts) for each interface must be OK. The optional device (“OP.” on the printouts) must match the model.
NOTE: The special jig is required for the loop back check for B-SP2D-GH20 (RS). If it is not used, the check will result in NG.
For B-SP2D-GH30, the Bluetooth device address must be printed for the optional device (“OP.” on the printouts).
2-33
3. ELECTRONICS
3. ELECTRONICS
3.1 BLOCK DIAGRAM
EO18-33014
(Revision Date: Jan. 29, 2004)
3.1 BLOCK DIAGRAM
3-1
3. ELECTRONICS
EO18-33014
3.2 CPU PC BOARD
3.2 CPU PC BOARD
This PC board is the central part of the printer, consisting of the following components and circuits:
•
CPU
•
Flash ROM (4MB)
•
SDRAM (8MB)
•
D/A Converter and Sensor Sensitivity Adjust Circuit
•
Reset Circuit
•
PLD (Programmable Logic Device)
•
IrDA Interface Driver/Receiver
•
Print Head Circuit
(1) CPU
A 32-bit CPU operates by the 30MHz internal clock. (External clock is 5.91MHz.)
This CPU includes 4-KB RAM, 16-bit timer (8 channels), 10-bit A/D converter (8 channels), DMA (4 channels), serial interface (3 channels), memory interface, etc., and processes the following:
•
Controlling the read/write of the SDRAM and flash ROM
•
Detecting and controlling the status of the various sensors and switches (Feed gap sensor, black mark sensor, strip/batch sensor, ambient thermistor, meida cove swtich, and FEED button)
•
Communicating with the RS-232C interface or Bluetooth module.
•
Controlling the print head circuit
•
Detecting the control signal of the stepping motor
•
Controlling the status LED
(2) Flash ROM (4MB)
This printer uses a 4MB flash ROM, on which the boot program and application program are written. This is also used to store the printer settings.
(3) SDRAM (8MB)
This printer uses a 8MB SDRAM, which is used to draw print data.
(4) D/A Converter and Sensor Sensitivity Adjust Circuit
The status signals from the feed gap/black mark sensor, strip/batch sensor, ambiment thermistor, print head voltage, print head broken element voltage, and print head temperature are sent to the A/D converter of the
CPU. The CPU acknowledges the printer status from these signals and processes the following:
•
Controlling the print start position
•
Controlling the printer ON/OFF
•
Controlling the print pulse
•
Detecting the issue mode
Also, the status signals are sent back to each sensor so that the sensor sensitivity can be optimized.
The D/A converter converts these feed back signals from digital to analog, and then outputs them to each sensors (feed gap/black mark sensor, strip/batch sensor).
(5) Reset Circuit
The reset circuit controls resetting the CPU, PLD, and flash ROM by monitoring the +3.3V.
After the power is turned on and the voltage becomes stable, the reset status of the CPU, PLD and flash ROM is released. When the power is turned off and the battery voltage drop is detected, the CPU and the flash
ROM are reset to protect the data and the circuit.
(6) PLD (Programmable Logic Device)
This component supports the CPU by processing the following:
•
Outputting data to the IrDA interface
•
Controlling the Bluetooth module
•
Controlling the print head circuit buffer
3-2
3. ELECTRONICS
EO18-33014
(Revision Date: Jan. 29, 2004)
3.3 DRIVER PC BOARD
(7) Print Head Circuit
This circuit sends print data to the print head and outputs the strobe signals, enable signals, etc.
The termistor signal output from the print head is transferred to the A/D converter of the CPU. The CPU uses this signal to control the print tone by detecting the print head temperature. This circuit also checks the voltage supplied to the print head and the print head broken element.
(8) Interface Circuit
To CN103 on the CPU PC board, various interface devices used to interface with the host or handy terminal are connected. The interface types are different depending on the models.
- RS-232C interface: GH20 model
- Bluetooth interface: GH30 model
- Wireless LAN: GH40 model
The IrDA driver/receiver is installed on the CPU PC board of the all models as standard,
3.3 DRIVER PC BOARD
This PC board, including the stepping motor driver, generator IC, etc, controls the stepping motor and generates the voltages from the battery supply voltage.
(1) Stepping Motor Driver
This circuit controls the stepping motor connected to Connector 2. Using the PM1 and PM2 signals output from the CPU PC board, it generates the PMA1, PMA2, PMB1, and PMB2 stepping motor drive signals.
Also, the PMEN signal output from the PLD on the CPU PC board is used as the driver's enable signal.
(2) Power Supply Circuit
This circuit generates the operating voltage for the logic ICs, print head, stepping motor, etc. from the voltage
VM (DC 7.4V) that is supplied from the Li-ion battery connected to Connector 3.
The 3.3V is used to operate the CPU, PLD, Flash ROM, SDRAM, etc. 5VB (5V) is used to operate the peripherals and control circuits, such as, the stepping motor driver, feed gap/black mark sensor, strip/batch sensor, print head (signal), etc.
The VH voltage is used as the operating voltage for the print head and stepping motor.
Also, this circuit protects itself when an overcurrent of the battery or an overvoltage is detected by cutting off the circuit.
3-3
4. PROGRAM DOWNLOAD
EO18-33014
(Revision Date: Jan. 29, 2004)
4.1 PROGRAM DOWNLOADING TO A WINDOWS MACHINE
4. PROGRAM DOWNLOAD
This section provides step by step instructions on how to setup and download the firmware to the B-SP2D portable printer. The software for performing the program download will allow the download of the firmware
(application program and character generator) from the provided floppy disk. The application program and the character generator are installed into the B-SP2D printer’s flash memory prior to being shipped to the customer. However, if specifications should change at a later date, this software will allow downloading firmware updates to the B-SP2D printer. The firmware download will be made from a personal computer via the IrDA interface (or RS-232C interface). Without this software, the firmware can be copied from the B-SP2D printer to another B-SP2D printer via IrDA communication.
4.1 PROGRAM DOWNLOADING TO A WINDOWS MACHINE
4.1.1 System Requirements
System
IBM compatible PC running Windows 95 ® , Windows 98 ® , Windows 2000 ® , or Windoes XP ®
(Performance of PC running other OS is not guaranteed.)
NOTE: Windows 95, Windows 98, Windows 2000, and Windows XP are registered trademarks of Microsoft
Corporation.
Installed memory of 16MB minimum (32MB or more is recommended.)
Available hard disk space of 10MB minimum (10MB or more is recommended.)
Interface
For IrDA communication, the IrDA interface should be provided for the PC (without drivers such as IrLAP) or an IrDA device which is connectable to a serial port should be provided for the PC.
For RS-232C communication, more than one serial port should be provided for the PC.
4.1.2 Setup
Before you can communicate from your PC to the B-SP2D printer, you must first copy the “Download Program for B-SP2D" from the three floppy disks provided to the hard disk of your PC.
B-SP2D Series
Download Program for B-SP2D (V1.0.0)
WR.FD-SP2D-DOWNLOAD
DISK(1/3)
7FM00479000
17th March 2003
V001.000
Copyright
2003
TOSHIBA TEC CORPORATION
All Rights Reserved
Setup Disk
Make sure that you have all three diskettes available of the “Download Program for B-SP2D”.
1. While running Windows 98 (or Windows 95, Windows 2000, Windows XP), insert Setup Disk (1/3) into the
PC floppydrive.
2. Click on the [START] button then highlight RUN and click on RUN.
3. When the RUN display appears, type in A:\SETUP.EXE and click on the [OK].
4-1
4. PROGRAM DOWNLOAD
EO18-33014
4.1 PROGRAM DOWNLOADING TO A WINDOWS MACHINE
4. By following the messages on the screen, perform the installation.
5. When the installation was completed successfully, the end screen appears. Click on the [Finish] button to end the installation.
4.1.3 Firmware Files Copy
If it ever becomes necessary to upgrade the firmware in the B-SP2D printer you will be supplied with a floppy disk containing the latest firmware revision similar to that shown below.
The files contained on the Install Kit can be copied to PC hard disk and then downloaded to the printer.
(Example)
B-SP2D Series
FIRMWARE(MAIN) V1.0
WR.FD-SP2D-FIRM
SP2D-MAIN-V10-Z920-E8.BIN
7FM00451000:E800
10th March 2003
V001.000
Copyright
2003
TOSHIBA TEC CORPORATION
All Rights Reserved
4.1.4 Running the Download Program for B-SP2D
1. Click on the [START] button to access the program menu.
2. Highlight Programs then highlight TOSHIBA TEC, B-SP2D, Download. And then click on Download
Program for B-SP2D in the screen display below.
3. The screen will change to display the initial screen of the Download Program as shown below.
4. After the download was completed successfully, from the [File(F)] drop down menu select [Exit(X)], and then click on the [OK] to terminate the download.
4-2
4. PROGRAM DOWNLOAD
EO18-33014
(Revision Date: Jan. 29, 2004)
4.2 COMMUNICATION PARAMETERS SETTING
4.2 COMMUNICATION PARAMETERS SETTING
This section provides communication parameters setting for the PC to perform the firmware download to the
B-SP2D printer. As the communication parameters, device, parity, interface, baud rate, and forced download mode can be set.
4.2.1 Communication Conditions
1. From the [tool(T)] drop down menu select [Condition(C)].
2. Select desired settings for device, parity, interface, and baud rate. Then click on the [OK].
NOTES: 1. After the PC starts up, COM1, None, RS-232C, and 9600bps are programmed as default setting.
2. To perform Forced Download, make a check in the check box "Forced download mode".
3. From the firmware version V1.1, IrCOMM protocol has been supported. When downloading the firmware by using the IrCOMM protocol, be sure to turn the printer to the system mode, as this is the only mode that enables downloading with the IrCOMM protocol. In case of Windows 95 and Windows 98, the data will be output to a virtual COM port. Set the virtual COM port for the Device. In case of the forced download, be sure to use the TEC protocol regardless of the protocol set for the printer.
NONE
4-3
4. PROGRAM DOWNLOAD
EO18-33014
(Revision Date: Jan. 29, 2004)
4.3 DOWNLOAD TO THE PRINTER
4.3 DOWNLOAD TO THE PRINTER
4.3.1 Conditions for Downloading
(1) IrDA (TEC Protocol) Interface
Item
Baud Rate
Stop Bit
Data Length
Parity
Forced Download
115200 bps
Specification
Normal Mode (Label mode, Receipt mode, TPCL-LE mode, System mode)
Depending on the communication protocol setting.
(9600/19200/38400/115200 bps)
1 bit
8 bit
None
(2) IrDA (IrCOMM) Interface
Protocol
Device Name
Service Name (Class name)
Minimum Turn Around Time
Link Release Threshold Time
IrCOMM (9-wire)
B-SP2D
IrDA: IrCOMM
1 msec.
12 sec.
(3) RS-232C Interface
Item
Baud Rate
Stop Bit
Data Length
Parity
Forced Download
115200 bps
None
Specification
Normal Mode (Label mode, Receipt mode, TPCL-LE mode, System mode)
Depending on the communicatio nprotocol setting.
(9600/19200/38400/115200 bps)
1 bit
8 bit
Depending on the communication protocol setting.
(None/Even)
(4) Printer to Printer
Baud Rate
Stop Bit
Date Length
Parity
115200 bps
1 bit
8 bit
None
4-4
4. PROGRAM DOWNLOAD
EO18-33014
(Revision Date: Jan. 29, 2004)
4.3 DOWNLOAD TO THE PRINTER
4.3.2 Status Indicator during Download
The following table shows the state of the status indicator and the printer during download.
Status Indicator Printer State
Receives an ACK (06H) twice when entering the
Download Mode.
When executing a loading preparation command, the printer detects a low battery or near low battery.
Communicating
IrDA (TEC Protocol) interfae
IrDA (IrCOMM) interface
RS-232C interface
Source printer
Printer to printer
Destination printer
Writing/deleting data to/from the Flash memory.
An error occurs during download.
Blinks in red twice.
Blinks in red.
Blinks in green.
Blinks in green and orange alternately.
Blinks in green.
Lights in green.
Blinks in red.
NOTES:
1. When downloading is completed properly, the printer will be automatically reset and started.
2. If an error occurs during a download, the printer will stop. To recover from the error state, it is necessary to turn off and then on the printer.
3. If an error occurs while the main program is downloaded, turn off and then on the printer. The printer will enter the download mode. Retry downloading.
4.3.3 Selecting a Firmware File
1. From the [File(F)] drop down menu select [Open(O)].
2. Select a binary file (*.BIN) to be downloaded.
4-5
4. PROGRAM DOWNLOAD
EO18-33014
4.3 DOWNLOAD TO THE PRINTER
3. The screen returns to the main menu screen, and the download file information will be shown as follows.
Make sure all items in the information box.
4.3.4 Forced Download to Printer
1. For IrDA communication, face the IrDA interface windows of both PC (or a device) and the printer, and then turn on the printer while pressing and holding the [FEED] button.
For RS-232C communication, connect the printer to the PC with the RS-232C cable, and then turn on the printer while pressing and holding the [FEED] button.
When the the status indicator blinks slowly in red twice, the printer enters the forced download mode.
CAUTION!
For RS-232C communication, use a battery-driven PC. If an AC-power-driven PC is used, a noise may occur on the signal line, causing the printer's CPU PC board to be damaged.
NOTE:
If the status indicator doesn't blink slowly in red twice, the printer doesn't enter the forced download mode. Retry to turn on the printer while pressing and holding the [FEED] button.
2. When the printer is in the forced download mode, open a file for downloading. And then, from the
[Transmission(R)] drop down menu select [Start(S)] to start the download.
NOTE:
Be sure to open a file for downloading first.
4-6
4. PROGRAM DOWNLOAD
EO18-33014
4.3 DOWNLOAD TO THE PRINTER
3. During data transmission, the screen below appears with a progress indicator at the bottom. When the file has been successfully transferred, the message below appears.
NOTES: 1. For IrDA communication, do not interrupt the IrDA interface windows of both PC and the printer nor move the PC and the printer during data transmission.
2. Never turn off the printer nor remove the battery from the printer during data transmission.
Doing so may cause an error.
3. If an error occurs during data transmision, retry from Step 1.
4.3.5 Execution of Download to Printer
1. Match the printer communication conditions for the PC and the printer. For IrDA communication, turn on the printer and face the IrDA interface windows of both PC (or a device) and the printer. (Direction of the printer's IrDA depends on the setting.)
For RS-232C communication, connect the printer to the PC with the RS-232C cable, and then turn on the printer.
When the the status indicator blinks slowly in red twice, the printer enters the download mode.
NOTE: If the status indicator doesn't blink slowly in red twice, the printer doesn't enter the download mode.
Turn off then on the printer, make sure the communication conditions, and then retry Step 1.
CAUTION!
For RS-232C communication, use a battery-driven PC. If an AC-power-driven PC is used, a noise may occur on the signal line, causing the printer's CPU PC board to be damaged.
2. When the printer is in the download mode, open a file for downloading. From the [Transmission(R)] drop down menu select [Start(S)] to start the download.
NOTE:
Be sure to open a file for downloading first.
4-7
4. PROGRAM DOWNLOAD
EO18-33014
4.3 DOWNLOAD TO THE PRINTER
3. During transmission, the screen below appears with a progress indicator at the bottom. When the file has been successfully transferred, the message below will appear.
NOTES: 1. For IrDA communication, do not interrupt the IrDA interface windows of both PC and the printer nor move the PC and the printer during data transmission.
2. Never turn off the printer nor remove the battery from the printer during data transmission.
Doing so may cause an error.
3. If an error occurs during data transmision, retry from Step 1.
4.3.6 Copying the Firmware from the Printer to Another Printer
Without using the PC, you can copy the firmware from the printer to another printer. By following procedures below, the firmware can be copied via IrDA communication at a high speed of 115.2K bps.
1. Make sure that the two printers are off, and then place them within 10 cm facing the IrDA interface windows.
IrDA Communication
2. Open the source printer cover, then turn on the power by pressing and holding the power button, resulting that the status indicator lights in red and then blinks in orange.
Keep pressing and holding the power button while the status indicator blinks in orange.
NOTE:
While the status indicator blinks in orange, the printer is waiting a response from the other printer which was inquired.
4-8
4. PROGRAM DOWNLOAD
EO18-33014
(Revision Date: Jan. 29, 2004)
4.3 DOWNLOAD TO THE PRINTER
3. During Step 2 (i.e. when the status indicator blinks in orange with the depression of the power button), turn on the destination printer by pressing and holding the [FEED] button. After the destination status indicator blinks in red twice, release the two buttons which are being held.
NOTE:
In case the destination status indicator doesn't blink in red twice, the printer doesn't enter the download mode. Retry to turn on the destination printer by pressing and holding the [FEED] button.
4. When ensuring the destination printer was on, the source one starts transferring the firmware data via IrDA communication.
5. During data transmission, the source status indicator blinks in green and in orange alternately. The destination one blinks in green.
NOTE:
After having received the data, the destination status indicator lights in green, indicating that the
Flash ROM erase and write is performed. Never turn off the printer nor remove the battery while the printer is working.
6. Data transmission is completed in approximately 3 minutes.
7. After the data transmission is completed successfully, the source status indicator keeps blinking in green.
After the Flash ROM erase and write was completed successfully, the destination printer restarts automatically while the status indicator blinks in red, blinks in green, then lights in green.
8. If an error occurs during data transmission, either of the status indicator blinks in red. Retry from Step 1.
NOTE:
Do not move the printers nor interrupt their IrDA interface windows during data transmission. Doing so may fail in IrDA communication.
4.3.7 Execution of Download by using the IrCOMM Protocol
1. Match the printer communication conditions for the PC and the printer. Turn on the printer while holding down the [FEED] key to turn the printer to the system mode. Face the IrDA interface windows of both PC
(or a device) and the printer. (Direction of the printer's IrDA depends on the setting.)
2. Click on the [Start(S)] of the [Transmission(R)] on the screen to start downloading.
When the printer enters the download mode, the status indicator slowly blinks in red twice.
When the printer is in the download mode, open a file for downloading.
NOTES: 1. Be sure to open a file for downloading first.
2. If the status indicator doesn't blink in red twice, the printer doesn't enter the download mode.
Turn off then on the printer, make sure the communication conditions, and then retry from
Step 1.
3. During transmission, the progress indicator is not displayed at the bottom of the screen.
NOTES: 1. For IrDA communication, do not interrupt the IrDA interface windows of both PC and the printer nor move the PC and the printer during data transmission.
2. Never turn off the printer nor remove the battery from the printer during data transmission.
Doing so may cause an error.
3. If an error occurs during data transmision, retry from Step 1.
4. Whether the downloading is completed properly or not is indicated by the status indicator as follows:
When succeeded: Blinks in green (downloading)
→
Lights in green (Writing data)
→
Blinks in green and red alternately. (Normal completion)
When error occurs: Blinks in red
4. After completing the download, be sure to turn off the printer by pressing the power button.
4-9
4. PROGRAM DOWNLOAD
EO18-33014
(Revision Date: Jan. 29, 2004)
4.4 DOWNLOAD TO THE WIRELESS LAN MODULE
4.4 DOWNLOAD TO THE WIRELESS LAN MODULE
Firmware download to the wireless LAN module can be performed by using the B-SP2D RFLAN F/W Download Tool.
In this section, the procedures for the firmware download to the wireless LAN module are provided.
4.4.1 System Requirements
System
IBM compatible PC running Windows
®
95, Windows
®
98, Windows
®
2000, or Windoes
®
XP
(Performance of PC running other OS is not guaranteed.)
NOTE: Windows 95, Windows 98, Windows 2000, and Windows XP are registered trademarks of Microsoft
Corporation.
Installed memory of 16MB minimum (32MB or more is recommended.)
Available hard disk space of 10MB minimum
Interface
IrDA interface is used for the communication between the PC and the printer.
When using the TEC Protocol, ACTiSYS ACT-IR220L+ (IrDA Com-Port Serial Adapter) is required.
When using the IrCOMM Protocol, use a communicable IrDA interface.
4.4.2 Setup
Before you can communicate from your PC to the B-SP2D printer, you must first copy the “FW Download
Tool" from the provided three floppy disks to the hard disk of your PC.
B-SP2D Series
F/W Download Tool
WR.FD-SP2D-RFLAN-DOWNLOAD
DISK(1/3)
7FM00558000
31st October 2003
V001.000
Copyright
2003
TOSHIBA TEC CORPORATION
All Rights Reserved
Setup Disk
Make sure that you have all three diskettes available of the “FW Download Tool”.
1. While running Windows 98 (or Windows 95, Windows 2000, Windows XP), insert Setup Disk (1/3) into the
PC floppydrive.
2. Click on the [START] button then highlight RUN and click on RUN.
3. When the RUN display appears, type in A:\SETUP.EXE and click on the [OK].
4. By following the messages on the screen, perform the installation.
5. When the installation was completed successfully, the end screen appears. Click on the [Finish] button to end the installation.
4-10
4. PROGRAM DOWNLOAD
EO18-33014
(Revision Date: Jan. 29, 2004)
4.4 DOWNLOAD TO THE WIRELESS LAN MODULE
4.4.3 Firmware Files Copy
If it ever becomes necessary to upgrade the firmware in the wireless LAN module you will be supplied with a floppy disk containing the latest firmware revision similar to that shown below.
The files contained on the Install Kit can be copied to PC hard disk and then downloaded to the printer.
B-SP2D RFLAN Module
FIRMWARE V1.0
RFLAN-FIRM-V100.BIN
31st August 2003
V001.000
Copyright
2003
TOSHIBA TEC CORPORATION
All Rights Reserved
4.4.4 Installation Procedure (When using the TEC Protocol)
1 Connect the ACT-IR220+ to the serial port of the PC.
Example
PC
ACT-IR220+
2 Confirm the IrDA settings of the PC in the following way.
Turn on the printer while pressing and holding the [FEED] key on the printer to start the printer in the system mode. Hold the [FEED] key until the indicator LED starts to blink in green. Since a diagnostic test result is automatically printed, confirm that the settings of the IrDA interface are "TEC 19200".
NOTE: Do not press the [FEED] key after the diagnostic test printing. Doing so causes the printer to enter another mode where printer parameters cannot be set.
4-11
4. PROGRAM DOWNLOAD
EO18-33014
(Revision Date: Oct. 26, 2004)
4.4 DOWNLOAD TO THE WIRELESS LAN MODULE
3 Run the firmware downloader, "B-SP2D RFLAN F/W Download Tool", on the PC.
4 Confirm that the settings of the downloader are as follows:
Control port of the Com Settings is IrDA: TEC Protocol.
The port number to which the ACT-IR220+ is connected is selected for the Com Settings Port.
NOTE: While the downloader is communicating with the wireless LAN module, do not switch the active window to another application.
4-12
4. PROGRAM DOWNLOAD
EO18-33014
(Revision Date: Jan. 29, 2004)
4.4 DOWNLOAD TO THE WIRELESS LAN MODULE
5 Place the ACT-IR220+ so that it faces to the IrDA interface window. Then, click on the [Start] button on the screen to be ready for downloading. (When the [Start] button is clicked, the printer's LED will blink in green.)
Example
IrDA Interface Window
B-SP2D Printer
ACT-IR220+
6 Click on the [File Open] button and select the firmware file to be downloaded.
7 Then, click on the [Download] button to start downloading.
4-13
4. PROGRAM DOWNLOAD
EO18-33014
(Revision Date: Oct. 26, 2004)
4.4 DOWNLOAD TO THE WIRELESS LAN MODULE
8 During data transmission, the screen below appears with a progress indicator at the bottom.
When the file has been successfully transferred, the message will appear in about 30 to 90 seconds. Click on the [OK] button.
CAUTION!
Never turn off the printer before the download completion message appears.
Total number of the download file blocks and the number of the transferred blocks
9 Click on the Close button to exit the downloader.
10 Press and hold the Power button on the printer to turn it off.
4-14
4. PROGRAM DOWNLOAD
EO18-33014
(Revision Date: Jan. 29, 2004)
4.4 DOWNLOAD TO THE WIRELESS LAN MODULE
4.4.5 Installation Procedure (When using the IrCOMM supporting IrDA)
When using the IrDA interface supporting the IrCOMM, such as, IrDA interface built in a laptop PC, the
IrCOMM Protocol should be used.
1 Confirm the IrDA settings of the PC in the following way.
Turn on the printer while pressing and holding the [FEED] key on the printer to start the printer in the system mode. Hold the [FEED] key until the indicator LED starts to blink in green. Since a diagnostic test result is automatically printed, confirm that the settings fo the IrDA interface are "IrCOMM".
NOTE: Do not press the [FEED] key after the diagnostic test printing. Doing so causes the printer to enter another mode where printer parameters cannot be set.
2 Run the firmware downloader, "B-SP2D RFLAN F/W Download Tool", on the PC.
3 Confirm that the settings of the downloader are as follows:
Control port of the Com Settings is IrDA: IrCOMM.
Vertual port for the IrDA is selected for the Com Settings Port.
NOTE: When the OS is Windows 2000 or Windows XP, COM port setting will be ineffective.
4 Place the PC and the printer so that their IrDA interface windows face each other. Then, click on the [Start] button on the screen to be ready for downloading. (When the [Start] button is clicked, the printer's LED will blink in green.)
Example
IrDA Interface Window
B-SP2D Printer
PC
5 Download the firmware to the wireless LAN module in the printer. After downloading is completed, turn off the printer. (Refer to Step 6 to Step 10 of Section 4.4.4.)
4-15
5. TROUBLESHOOTING
EO18-33014
5. TROUBLESHOOTING
5. TROUBLESHOOTING
Problem
The printer is not turned on.
The printer does not print media.
(The status indicator blinks in red.)
Cause
1. The battery is not loaded correctly.
2. The battery terminal is disconnected from the soldering part.
3. CPU PC board ass'y failure or Drive PC board ass'y failure
Corrective action
Re-load the battery correctly.
Replace the battery terminal.
1. The media roll is not loaded correctly.
2. The media cover is not closed completely.
3. The media is jammed in the printer.
4. The print head FFC harness or the print head element is broken.
5. The print head temperature reached the upper limit of the operating temperature.
6. A communication error occurred.
7. Flash ROM write error or erase error occurred.
8. There is insufficient area in the flash ROM.
9. The print mode is not selected correctly.
1. The battery voltage is low.
Replace the CPU PC board ass'y or the Drive PC board ass'y.
Re-load the media roll correctly.
Close the media cover completely.
Remove the jammed media and re-load the media roll correctly.
Replace the print head FFC harness or the print head ass'y.
Open the media cover and allow the print head to cool.
Check that the interface cable is connected firmly.
Check the communication parameters.
Open the media cover and close it again.
Replace the CPU PC board ass'y.
Open the media cover and close it again.
Erase the data.
Open the media cover and close it again.
Send the correct print mode from the PC or handy terminal.
Turn off the printer and replace the battery with a fully charged one.
The printer does not print media.
(The status indicator lights in red.)
The printer does not print media.
(The status indicator lights in orange.)
The [FEED] button does not function.
1. The battery is nearly end.
1. The [FEED] button is depressed incompletely.
Replace the battery with a fully charged one as soon as possible.
Press the [FEED] button more strongly.
Replace the CPU PC board ass'y.
5-1
5. TROUBLESHOOTING
EO18-33014
5. TROUBLESHOOTING
Problem
The printer does not print labels one by one in the strip mode or specified number of labels in the batch mode.
A cover open error occurs after closing the media cover.
The printer does not print by radio communication.
Poor print quality
The print start position is not detected.
PC board ass'y.
broken.
PC board ass'y.
2. Print head failure
3. Platen failure
Cause
1. The sensors are not adjusted properly.
2. The sensors are not installed properly.
3. The sensors are dirty.
4. The sensors are disconnected from the CPU
1. Either side of the media cover is unlocked.
2. The media cover switch failure
1. Interface PC board ass'y failure
2. CPU PC board ass'y failure
3. Interface PC board ass'y is disconnected from the CPU PC board ass'y.
4. The FPC cable for the interface PC board is
1. The print head is dirty.
2. Unspecified media is used.
1. The sensor is not adjusted properly.
2. The sensor is not installed properly.
3. The sensor or the sensor filter is dirty.
4. The sensor is disconnected from the CPU
The power switch does not perform.
The battery cover is not closed completely.
Print tone is uneven.
A print error occurs in the feed direction.
1. Power switch failure or CPU PC board ass'y failure
1. The battery cover failure
2. The top cover failure
1. The print head is dirty.
2. The print head ass’y is not installed in position.
3. The print head failure
4. The platen failure
1. Failure in the motor idler gear, platen idler gear, idler gear, or platen gear
Corrective action
Re-adjust the sensors.
Re-install the sensors.
Clean the sensors.
Connect the sensors to the
CPU PC board ass'y.
Close the media cover until both sides of the cover click in position.
Replace the media cover switch.
Replace the interface PC board ass'y.
Replace the CPU PC board ass'y.
Connect the interface PC board ass'y with the CPU PC board ass'y completely.
Replace the FPC cable for the interface PC board.
Clean the print head.
Change the media to the specified one.
Re-adjust the sensor.
Re-install the sensor.
Clean the sensor and sensor filter.
Connect the sensor to the
CPU PC board ass'y completely.
Replace the power switch or the CPU PC board ass'y.
Replace the battery cover.
Replace the top cover.
Clean the print head.
Re-install the print head ass'y correctly.
Replace the print head ass'y.
Replace the platen.
Replace the motor idler gear, platen idler gear, idler gear, or platen gear.
Replace the print head ass'y.
Replace the platen.
5-2
6. OPTIONAL EQUIPMENT
EO18-33014
6.1 HOW TO USE THE BATTERY CHARGER (B-SP2D-CHG-QM)
6. OPTIONAL EQUIPMENT
6.1 HOW TO USE THE BATTERY CHARGER (B-SP2D-CHG-QM)
WARNING!
1.
The B-SP2D-CHG battery charger is exclusively used for the B-SP2D-BT lithium-ion battery pack.
DO NOT charge any other battery packs, or explosion, combustion, heat may result.
2.
If the battery charger gives out smoke, bad smell, or extraordinary heat, unplug the power cord from the outlet immediately. Failure to do this may cause fire or electric shock.
NOTE:
Since the power cord set is not enclosed in this battery charger unit, please purchase an approved one which meets the standard for each country from your Authorized TOSHIBA TEC representative. For details, please refer to the B-SP2D-CHG Owner's Manual.
Battery Pack (B-SP2D-BT)
3
Battery Charger (B-SP2D-CHG)
1
AC Power Cord
2
1) Connect the AC power cord to the charger.
2) Connect the AC plug to a wall outlet.
3) Install the battery pack.
The CHARGE lamp will light and charging will begin. The CHARGE lamp indicates how much the battery pack is charged.
CHARGE Lamp
CHARGE lamp
OFF
Red
Green
Blinking red
State
Unconnected.
Charged.
Completed.
Abnormal state
4) After charging is completed, remove the battery pack from the battery charger.
5) Disconnect the power cord from the AC outlet.
6-1
6. OPTIONAL EQUIPMENT
EO18-33014
(Revision Date: Jan. 29, 2004)
6.2 HOW TO USE THE BATTERY CHARGER (B-SP2D-CHG5-QM)
Charging time
To charge an empty battery pack:
Battery pack
B-SP2D-BT
Charging time about 3 hours
• The charging time may differ depending on the condition of the battery pack or the temperature of the environment.
NOTES:
1. Battery packs should be charged on condition that both ambient temperature and battery temperature fall within a range of 0 °C to 40°C.
2. The battery charger will get warmer during charging (room temperature + about 30°C). This is not abnormal state.
3. When a completely discharged battery is charged, the CHARGE lamp may not light for a while. Leave the battery charger and the battery pack alone for a few minutes.
Stop using that battery pack if the CHARGE lamp does not light yet. The battery pack is faulty.
4. Periodically clean the charger terminals with a dry cloth.
6.2 HOW TO USE THE BATTERY CHARGER (B-SP2D-CHG5-QM)
WARNING!
1.
The B-SP2D-CHG5 battery charger is exclusively used for the B-SP2D-BT lithium-ion battery pack.
DO NOT charge any other battery packs, or explosion, combustion, heat may result.
2.
If the battery charger gives out smoke, bad smell, or extraordinary heat, unplug the power cord from the outlet immediately. Failure to do this may cause fire or electric shock.
NOTE:
Since the power cord set is not enclosed in this battery charger unit, please purchase an approved one which meets the standard for each country from your Authorized TOSHIBA TEC representative. For details, please refer to the B-SP2D-CHG5 Owner's Manual.
Battery Pack (B-SP2D-BT)
Battery Charger (B-SP2D-CHG5)
4
AC Adapter
1
2
AC Power Cord
3
1) Connect the enclosed AC adapter to the battery charger.
2) Connect the AC power cord to the AC adapter.
3) Connect the AC plug to an AC outlet.
4) Install the battery pack.
The CHARGE lamp will light and charging will begin. The CHARGE lamp indicates how much the battery pack is charged. Maximum of 5 battery packs can be charged at the same time.
CHARGE lamp
OFF
Red
Green
Blinking red
State
Unconnected.
Charged.
Completed.
Abnormal state
CHARGE Lamp
6-2
6. OPTIONAL EQUIPMENT
EO18-33014
(Revision Date: Jan. 29, 2004)
6.2 HOW TO USE THE BATTERY CHARGER (B-SP2D-CHG5-QM)
5) After charging is completed, remove the battery pack from the battery charger. The CHARGE lamp will not go off immediately after the battery pack is removed, but this is not abnormal.
6) Disconnect the AC plug from the AC outlet.
Charging time
To charge an empty battery pack:
Battery pack
B-SP2D-BT
Charging time about 3 hours
• The charging time may differ depending on the condition of the battery pack or the temperature of the environment.
NOTES:
1. Battery packs should be charged on condition that both ambient temperature and battery temperature fall within a range of 0 °C to 40°C.
2. The battery charger will get warmer during charging (room temperature + about 30°C). This is not abnormal state.
3. When the CHARGE lamp blinks in red, it means a battery pack error. As the life of the battery pack may be expired, replace it with a new one.
4. If the CHARGE lamp does not light in red even if a battery pack is installed, check the following:
• The AC power cord or AC adapter’s plug may not be connected properly. Connect it properly.
• The charging terminal of the battery charger or the battery pack is stained. Wipe it clean with a dry soft cloth.
• When the battery’s over discharge protector has been operated, leave the battery charger and the battery pack alone for a few minutes. Stop using the battery pack if the CHARGE lamp does not light at all.
5. Periodically clean the charger terminals with a dry cloth.
6-3
7. WIRELESS LAN PARAMETER SETTING
EO18-33014
(Revision Date: Oct. 26, 2004)
7.1 WHEN USING THE RFLAN CONFIGURATION TOOL
7.
WIRELESS LAN PARAMETER SETTING
This section provides the parameter setting procedure for the wireless LAN module. There are two parameter setting methods: One uses the B-SP2D RFLAN Configuration Tool and the parameters are set via IrDA.
The other uses the Web browser and the parameters are set via wireless LAN.
NOTES:
1. Since the available frequency of the wireless LAN is different from country to country, it is required to select the country from JA, EU, US, France, and Spain. (When the printer is delivered, EU is selected.)
When the printer is used in the U.S.A., France, or Spain, select the appropriate country.
2. The set parameters are stored in the wireless LAN module.
3. RFLAN Configuration Tool V1.0 covers wireless LAN module V7xx only. RFLAN Configuration Tool V1.1
covers both of wireless LAN module V1xx and V7xx.
7.1 WHEN USING THE RFLAN CONFIGURATION TOOL
7.1.1 System Requirements
System
IBM compatible PC running Windows
®
95, Windows
®
98, Windows
®
2000, or Windoes
®
XP
(Performance of PC running other OS is not guaranteed.)
NOTE: Windows 95, Windows 98, Windows 2000, and Windows XP are registered trademarks of Microsoft
Corporation.
Installed memory of 16MB minimum (32MB or more is recommended.)
Available hard disk space of 10MB minimum
Interface
Communicatin between the PC and the printer should be via IrDA interface.
When using the TEC Protocol, ACTiSYS ACT-IR220L+ (IrDA Com-Port Serial Adapter) is required.
When using the IrCOMM Protocol, use the communicable IrDA interface.
7.1.2 Setup
Before you can communicate from your PC to the B-SP2D printer, you must first copy the “RFLAN Configuration Tool" from the provided three floppy disks to the hard disk of your PC.
B-SP2D RFLAN
Configuration Tool
WR.FD-SP2D-RFLAN-PARATOOL
DISK(1/3)
7FM00557000
31st October 2003
V001.000
Copyright
2003
TOSHIBA TEC CORPORATION
All Rights Reserved
Setup Disk
Make sure that you have all three diskettes available of the “RFLAN Configuration Tool”.
1. While running Windows 98 (or Windows 95, Windows 2000, Windows XP), insert Setup Disk (1/3) into the
PC floppydrive.
2. Click on the [START] button then highlight RUN and click on RUN.
3. When the RUN display appears, type in A:\SETUP.EXE and click on the [OK].
7-1
7. WIRELESS LAN PARAMETER SETTING
EO18-33014
(Revision Date: Jan. 29, 2004)
7.1 WHEN USING THE RFLAN CONFIGURATION TOOL
4. By following the messages on the screen, perform the installation.
5. When the installation was completed successfully, the end screen appears. Click on the [Finish] button to end the installation.
7.1.3 Parameter Setting Procedure (when using TEC Protocol)
When using the TEC Protocol, ACTiSYS ACT-IR220L+ (IrDA Com-Port Serial Adapter) is required.
1.Connect the ACT-IR220L+ to the serial port of the PC.
Example
PC
ACT-IR220+
2. Confirm the IrDA settings of the printer in the following way.
Turn on the printer while pressing and holding the [FEED] key on the printer to start the printer in the system mode. Hold the [FEED] key until the indicator LED starts to blink in green. Since a diagnostic test result is automatically printed, confirm that the settings fo the IrDA interface are "TEC 19200".
NOTE: Do not press the [FEED] key after the diagnostic test printing. Doing so causes the printer to enter another mode where printer parameters cannot be set.
7-2
7. WIRELESS LAN PARAMETER SETTING
EO18-33014
(Revision Date: Oct. 26, 2004)
7.1 WHEN USING THE RFLAN CONFIGURATION TOOL
3 Run the parameter setting application, RFLAN Configuration Tool, on the PC.
NOTE: While the RFLAN Configuration Tool is communicating with the wireless LAN module, do not switch the active window to another application.
4 Confirm that the settings of the application are as follows:
Control port of the Com Settings is IrDA: TEC Protocol.
The port number to which the ACT-IR220+ is connected is selected for the Com Settings Port.
7-3
7. WIRELESS LAN PARAMETER SETTING
EO18-33014
(Revision Date: Oct. 26, 2004)
7.1 WHEN USING THE RFLAN CONFIGURATION TOOL
5 Place the ACT-IR220+ so that it faces to the IrDA interface window. Then, click on the [Start] button on the screen to be ready for downloading. (When the [Start] button is clicked, the printer's LED will blink in green.)
IrDA Interface Window
B-SP2D Printer
ACT-IR220+
6 After setting each parameter, click on the [Send Para] button. The setting data will be donwloaded to the wireless LAN module. During transmission, the parameters being downloaded are shown below the [Send
Para] button.
[Send Para] button
[Restore] button [Get Para] button
ROM Version
IP Address
Gateway Address
Subnet Mask
Socket Port No.
DHCP ID
Host Name
WINS Server
Address
RF-LAN
Security Setting
WEP Type
Send Key
Key #1 to #4
User Name
Password
ESS ID
Connection Mode
Channel No.
Authentication
SE Mode
NOTES:
1. How to call the factory set initial settings
Clicking on the [Restore] button resets the parameter settings to the initial values that were set at the shipment from the factory. Regarding the IP address, the upper 2 bytes are fixed to "172.16", and the lower 2-byte number is set to the printer ID. However, the IP address called by the [Restore] button will be always "172.16.0.10".
Also, clicking on the [Restore] button disables the [Get Para], [Send Para], and [Restore] buttons until the factory set initial values have been displayed.
2. How to call the currernt settings
Clicking on the [Get Para] button displays the current settings.
If an unavailable channel has been set for the selected country, it will be automatically changed to a proper channel on this tool. (Applicable from the RFLAN Configuration Tool V1.1.)
3. How to save and load the settings
It is possible to save the parameter settings shown on the screen and to load the saved parameter settings.
7-4
7. WIRELESS LAN PARAMETER SETTING
EO18-33014
(Revision Date: Oct. 26, 2004)
7.1 WHEN USING THE RFLAN CONFIGURATION TOOL
Save
Click on the File menu and select the Save(S) to show the File save screen. Name the file and save.
Load
Click on the File menu and select the Load(L) to show the File load screen. Specify the file name and load it.
NOTE: On the RFLAN Configuration Tool screen, parameters to be set are shown in boldface and those to be omitted (skipped) are shown in normal style. These are also saved or loaded.
(Applicable from the RFLAN Configuration Tool V1.1.)
4. Description of each parameter
Firmware version of the wireless LAN module
ROM Version: ROM version No. of the printer
TCP/IP setting
IP Address:
Gateway Address:
Subnet Mask:
LPD:
IP Address (Default: 172.16.xxx.xxx)
Printer ID
Setting value: xxx.xxx.xxx.xxx
Gateway IP Address (Default: 0.0.0.0)
Setting value: xxx.xxx.xxx.xxx
Subnet Mask (default: 255.255.0.0)
Setting value: xxx.xxx.xxx.xxx
Whether LPD protocol is enabled or disabled. (Default: Enabled)
: Disabled
: Enabled
Socket:
Socket Port:
DHCP:
DHCP ID:
HOST:
WINS:
Whether Socket communication is enabled or disabled. (Default: Enabled)
: Disabled
: Enabled
Port No. to be use for socket communication (Default: 8000)
Setting value: 0 - 65535
Whether DHCP Client Protocol is enabled or disabled. (Default: Disabled)
: Disabled
: Enabled
Client ID to be notified to the DHCP server when using DHCP
(Default: MAC Address)
Host name to be notified to the host when using DHCP, WINS Protocol
Max. 32 bytes (Default: MAC Address)
Whether WINS Protocol is enabled or disabled, and WINS Server address
(Default: OFF)
Disable: OFF
ON (STATIC): WINS Server assigned is used.
ON (DHCP): WINS Server notified by the DHCP Server is used.
WINS Server Address: WINS server address (Default: 0.0.0.0)
Setting value: xxx.xxx.xxx.xxx
RF-LAN Basic Settings
ESS ID:
Connection Mode:
Channel:
Authentication:
ESS ID (Network Name) (Default: TOSHIBA TEC)
Max. 32 bytes
Connection mode (Default: Infrastructure)
Infrastructure mode
Adhoc mode
Channel to be used for Adhoc communication (Default: 1)
Channel No. using only Adhoc mode
Authentication method (Default: Open system)
Open system
Shared key
7-5
7. WIRELESS LAN PARAMETER SETTING
EO18-33014
(Revision Date: Oct. 26, 2004)
7.1 WHEN USING THE RFLAN CONFIGURATION TOOL
5. Parameters to be set are shown in boldface on the screen of the RFLAN Configuration Tool. Those to be omitted are shown in normal style and skipped when the parameter settings are downloaded. This makes the download time shorter.
Whether to set the parameter or not can be switched alternately by double-clicking. (Applicable from the RFLAN Configuration Tool V1.1.)
6. Clicking on the [Send Para] button disables the [Get Para], [Send Para], and [Restore] buttons until the parameter settings have been downloaded to the wireless LAN module.
SE Settings
Country: Country where the printer is used. (Default: EU)
EU: Europe
US: America
FRA: France
ESP: Spain
JA: Japan
NOTE: Since the frequency band of the wireless LAN is different from country to country, it is necessary to set the country. To set the country, a password entry is required. Click on the Help(H) menu and then SE
Mode, the password entry screen will appear. Type in "B-SP2D" and click on the [OK] button.
Select the country on the screen.
NOTE: When the country is changed, selectable channels are also changed. After changing the country, be sure to set the available channel. (Applicable from the RFLAN Configuration
Tool V1.1.)
Country Available channel
EU
US
FRA
ESP
JA
1 to 13
1 to 11
10 to 13
10 to 11
1 to 14
7-6
7. WIRELESS LAN PARAMETER SETTING
EO18-33014
(Revision Date: Oct. 26, 2004)
7.1 WHEN USING THE RFLAN CONFIGURATION TOOL
RF-LAN Security Settings
WEP Type:
Send Key:
Security:
Key #1 to #4:
Whether WEP key is enabled or disabled. (Default: OFF)
Disable: OFF
ON (40 bits): Enabled (The length of the WEP Key is 40 bits)
ON (140 bits): Enabled (The length of the WEP Key is 104 bits)
WEP key number to be used for transmission
1: Key #1
2: Key #2
3: Key #3
4: Key #4
Security mode (Default: OFF)
OFF: Disabled
MD5: MD5
LEAP: LEAP (Applicable from the RFLAN Configuration Tool is V1.1.)
Setting for WEP Keys #1 to #4 (Default: 0000 [NUL 13 bytes])
When the WEP Type is set to 104 bits, the all bits are effective. When set to
40 bits, the top 40 bits (5 bytes) only are effective.
Key #1
Key #2
Key #3
Key #4
5 bytes 13 bytes
User:
Pass:
User name to be used for authentication (Default: 0000 [NUL 32 bytes])
Max. 32 bytes
Password to be used for authentication (Default: 0000 [NUL 32 bytes])
Max. 32 bytes
NOTE: The entered password is displayed as "*****" on the screen.
For details of each parameter, refer to Section 7.2.9.
7. After setting the parameters, click on the Close button to exit the appliation.
8. Press and hold the Power button on the pritner to turn it off.
7-7
7. WIRELESS LAN PARAMETER SETTING
EO18-33014
(Revision Date: Jan. 29, 2004)
7.1 WHEN USING THE RFLAN CONFIGURATION TOOL
7.1.4 Parameter Setting Procedure (when using IrCOMM Protocol)
When using the IrDA interface supporting the IrCOMM, such as, IrDA interface built in a notebook PC, the
IrCOMM Protocol should be used.
Example
IrDA Interface Window
B-SP2D Printer
PC
1. Confirm the IrDA settings of the PC in the following way.
Turn on the printer while pressing and holding the [FEED] key on the printer to start the printer in the system mode. Hold the [FEED] key until the indicator LED starts to blink in green. Since a diagnostic test result is automatically printed, confirm that the settings fo the IrDA interface are "IrCOMM".
NOTE: Do not press the [FEED] key after the diagnostic test printing. Doing so causes the printer to enter another mode where printer parameters cannot be set.
2 Run the parameter setting application, "RFLAN Configuration Tool", on the PC.
7-8
7. WIRELESS LAN PARAMETER SETTING
3. Confirm that the settings of the downloader are as follows:
Control port of the Com Settings is IrDA: IrCOMM.
Vertual port for the IrDA is selected for the Com Settings Port.
EO18-33014
(Revision Date: Oct. 26, 2004)
7.1 WHEN USING THE RFLAN CONFIGURATION TOOL
NOTES:
1. When the OS is Windows 2000 or Windows XP, COM port setting will be ineffective.
2. While the RFLAN Configuration Tool is communicating with the wireless LAN module, do not switch the active window to another application.
4. Place the PC and the printer so that their IrDA interface windows face each other. Then, click on the
[Start] button on the screen to be ready for downloading. (When the [Start] button is clicked, the printer's
LED will blink in green.)
IrDA Interface Window
B-SP2D Printer
PC
5. Refer to Section 7.1.3 and set the parameters, then download the settings to the printer.
7-9
7. WIRELESS LAN PARAMETER SETTING
EO18-33014
(Revision Date: Oct. 26, 2004)
7.2 WHEN USING THE WEB BROWSER
7.2 WHEN USING THE WEB BROWSER
It is possible to access the printer’s website at “http://[printer’s IP address]/” by using the web browser. From this website, the wireless LAN parameters can be set.
There are the Info, Wireless, IP Addr, and Admin tabs on the web page. On each page, it is possible to browse and set the parameters.
The URL, http://[printer’s IP address]/maintenance.html, allows an access to the printer maintenance web page. On this page, the country where the printer is used and UART baud rate can be set.
For details, refre to the following sections.
7.2.1 Wireless Parameter Print
First, print the wireless LAN module's parameter setting before setting the parameters.
Pressing and holding the Power button while the printer power is off causes the printer to turn on and print a wireless LAN parameter settings label regardless of the issue mode. If the label is not printed successfully due to an error, it is required to turn off the power, and then retry from the beginning. This is because the printer will not print the label even if the error is cleared.
Although the wireless LAN parameter settings label is also printed by sending a reset command while holding down the Power button of the printer in operation, these printed parameter settings are not effective. Therefore, the parameter settings label must be printed when the printer power is off.
Version
Sample
RF-LAN PARAMS[100] |TYPE[EU ]
IP [172.016.000.010] |LPR [ON ]
GW [000.000.000.000] |DHCP[ON ]
SUB [255.255.000.000] |CON [INF]
SOCK [ON ][65535] |AUTH[SKEY]
WEP [128]|SECU[MD5] |CHAN[07]
WINS [ON ][000.000.000.000]
HOST [TTEC ]
[
ESSID [TEC
[
MAC:0010C61CCDA9
]
]
]
Item
IP
GW
SUB
SOCK
TYPE
Parameter
Module Version
IP Address
Gateway IP Address
Subnet Mask
Socket communication
Socket port
Country where the printer is used.
xxx
Setting xxx.xxx.xxx.xxx
xxx.xxx.xxx.xxx
xxx.xxx.xxx.xxx
ON/OFF
0 to 65535
EU/US/JP/FRA/ESP
[xxx]
[xxx.xxx.xxx.xxx]
[xxx.xxx.xxx.xxx]
[xxx.xxx.xxx.xxx]
[ON ] [OFF]
[00000] to [65535]
[EU ] [US ] [JP ]
LPR
DHCP
CON
AUTH
WEP
SECU
CHAN
WINS
LPR communication
DHCP
Connection mode
Authentication method
WEP
Security mode
Used channel
WINS
ON/OFF
ON/OFF
Infrastructure/Adhoc
Open system/Shared key
OFF/ON (40 bits)/ON (128 bits)
OFF/MD5 /LEAP
0 to 14
[FRA] [ESP]
[ON] [OFF]
[ON ] [OFF]
[INF][ADH]
[OPEN] [SKEY]
[OFF][ 40] [128]
[OFF ] [MD5 ] [LEAP]
[00] to [14]
OFF/ON (STATIC)/ON(DHCP) xxx.xxx.xxx.xxx
[OFF ] [ON ] [DHCP]
[xxx.xxx.xxx.xxx]
HOST
ESSID
Host name
ESS ID xxxxxxxx… (Max. 32 bytes) xxxxxxxx… (Max. 32 bytes)
[xxxxxxxx…]
[xxxxxxxx…]
Barcode
IP Address xxx.xxx.xxx.xxx
A bar code is printed.
NOTE: LEAP is selectable for the security mode only when the wireless LAN module version is V1xx.
7-10
7. WIRELESS LAN PARAMETER SETTING
7.2.2 Info Page
The current printer state is displayed.
EO18-33014
(Revision Date: Oct. 26, 2004)
7.2 WHEN USING THE WEB BROWSER
Connected to SSID:
Using channel:
Currently used SSID
Currently used channel
MAC address of Access Point: IP address of the currently connected access point
Current transmission rate (Mbits/s): Current transmission rate
Current communication quality (%): Ratio of successfully sent packets to the all packets
MAC address of the Module: MAC address of the wireless LAN module
Current IP address: Currently used IP address (When DHCP is enabled, the leased
IP address is displayed.)
Module Firmware version: Firmware version of the wireless LAN module
7-11
7. WIRELESS LAN PARAMETER SETTING
EO18-33014
(Revision Date: Oct. 26, 2004)
7.2 WHEN USING THE WEB BROWSER
7.2.3 Wireless Page
The parameter settings associated to the wireless LAN module can be browsed or changed.
Operating Mode:
The SSID:
Channel:
EAP Authentication:
User name for EAP:
Password for EAP:
WEP Enabled:
WEP Key length:
Connection mode
SSID to be used.
Channel to be used in Adhoc mode
Security protocol to be used.
User name to be used for the security protocol (See NOTE.)
Password to be used for the security protocol (See NOTE.)
Whether WEP is enabled or disabled.
WEP key length
WEP Key 1 – 4:
WEP key to use:
WEP keys #1 to #4 (See NOTE.)
WEP key to be used for transmission
Shared key Authentication: Whether the shared key authentication mode is enabled or disabled.
When it is disabled, the authentication will be open system.
Power save timeouts: Time that the wireless LAN module takes to enter the power save mode.
For details, refer to Section 7.2.9.
NOTE: The entered data are displayed as "
• • • •
" on the browser for security. (Wireless LAN module version V1xx.)
7-12
7. WIRELESS LAN PARAMETER SETTING
EO18-33014
(Revision Date: Oct. 26, 2004)
7.2 WHEN USING THE WEB BROWSER
7.2.4 IP Addr Page
The parameter settings associated to the IP address can be browsed or changed.
IP Address mode:
Default IP Address:
Default Subnet Mask:
Default gateway:
DHCP ID:
Use Socket Only printing:
DHCP ID used for the DHCP client protocol
Whether printing by socket communication is enabled or disabled.
Printing Port for Socket Only: Port number used for printing by socket communication
Use LPD printing: Whether printing by using LPR protocol is enabled or disabled.
WINS Client: Whether WINS protocol is enabled or disabled, and WINS server address acquisition method
Wins server address:
IP Address setting mode
IP Address setting
Subnet mask setting
Gateway setting
Host name:
WINS server address
Only when the WINS client parameter is set to ON (Static), this setting is effective.
Host name
For details, refer to Section 7.2.9.
7-13
7. WIRELESS LAN PARAMETER SETTING
EO18-33014
(Revision Date: Oct. 26, 2004)
7.2 WHEN USING THE WEB BROWSER
7.2.5 Admin Page
The parameter settings can be initialized or the wireless LAN module can be rebooted.
Reboot Module: Used to restart the wireless LAN module.
Restore factory defaults: Used to restore the parameter settings to the initial values.
7.2.6 Maintenance Page
The country where the printer is used and the transmission rate between the wireless LAN module and the printer can be set. Note that this page is exclusively for service personnel.
The URL, http://[printer’s IP address]/maintenance.html, allows an access to this page.
ExpChannel: Country where the wireless LAN module is used.
UART baudrate: Transmission rate between the wireless LAN module and the printer
For details, refer to Section 7.2.9.
7-14
7. WIRELESS LAN PARAMETER SETTING
EO18-33014
(Revision Date: Jan. 29, 2004)
7.2 WHEN USING THE WEB BROWSER
7.2.7 Parameter Settings at Power On Time
When the printer is started in the usual way, the wireless LAN module is started according to the parameter settings stored in the wireless LAN module. However, when the printer is started while holding the Feed button, the wireless LAN module is not started at the time of diagnostic test label printing. Accordingly, communication via wireless LAN module cannot be performed.
Exceptionally, if the printer is restarted by the reset command while the Feed button is held in online mode, a communication via wireless LAN is possible even after the diagnostic test label printing. However, this does not meet the specification and the parameters should not be set in this state.
When the slant line pattern has been printed by pressing the Feed button after the diagnostic test label printing, the wireless LAN module will restart according to the following specific parameter settings, regardless of the stored settings.
IP Address: 172.16.0.10
Subnet Mask: 255.255.0.0
DHCP: Disabled
WINS: Disabled
ESSID: TTEC
Connection mode: Adhoc
Channel: 10
Authentication: Open
WEP: Disabled
Security: Disabled
For the parameter settings other than above, the stored settings are effective. The above parameter settings allows always connecting to the printer on the same settings, regardless of the stored settings.
7.2.8 IP Address Setting by Using the ID Setting Command
After the printer is started while holding down the Feed button and the diagnostic test label is printed, the printer
ID and the printer IP address can be set at the same time, by using the ID command.
The printer IP address consists of the upper 2 bytes of “172.16” and the lower 2-byte number which is equal to the printer ID. At this time, the subnet mask is set to 255.255.0.0.
NOTES:
1. When both of the following conditions are satisfied, only the printer ID is set.
•
When the ID command is sent in online mode after the printer prints the diagnostic test label and the slant line pattern.
•
When the wireless LAN IP address disabling parameter of the ID command is set with “, 0”.
2. IP address setting is possible only right after the diagnostic test label is printed, therefore, the command cannot be sent via wireless LAN interface.
7-15
7. WIRELESS LAN PARAMETER SETTING
EO18-33014
(Revision Date: Oct. 26, 2004)
7.2 WHEN USING THE WEB BROWSER
7.2.9 Wireless LAN Parameter List and Initial Values
(1) Wireless LAN Parameter List and Wireless LAN Module’s Initial Value
The following table shows the wireless LAN parameters and the wireless LAN module’s initial values. The wireless LAN module’s initial values can be obtained by clicking on the Restore button on the parameter setting screen via both IrDA and HTTP.
NOTE: LEAP is selectable for the security mode only when the wireless LAN module version is V1xx.
7-16
7. WIRELESS LAN PARAMETER SETTING
EO18-33014
(Revision Date: Feb. 17, 2004)
7.2 WHEN USING THE WEB BROWSER
(2) Factory Set Initial Values
All wireless LAN parameter settings of the factory set initial values, except IP address, are same as those of wireless LAN module’s initial values. Regarding the IP address of the factory set initial value, the upper 2 bytes of the IP address are fixed to 172.16, and the lower 2-byte number equals to each printer ID.
NOTE: Country Setting
When the printer is turned on, the country settings for the printer and the wireless LAN module are compared and the final country setting is determined.
When the country setting for the printer is “JP”, it takes precedence over that for the wireless LAN module. For example, whenever the printer’s country setting is “JP”, the setting for the wireless LAN will be automatically changed to “JP” at the power on time, regardless of the wireless LAN module’s setting.
In order to set to a desired country other than “JP”, it is necessary to set “QM” for the printer before setting for the wireless LAN module.
The following table shows the combination of the country settings and the final result of the wireless LAN module.
Countery Setting for the Printer
Country Setting for the Wireless LAN Module
JP EU US France Spain Other
JP JP JP JP JP JP JP
QM EU EU US FRA ESP Other
The country setting may need to be changed according to each country's Radio Law. Refer to the following table, and, if necessary, change the country setting for the wireless LAN module before selling the printers or after replacing the wireless LAN module.
As the all printers have been shipped from the factory with the country setting of "EU", there is no need to change the country setting when the setting corresponds to "EU".
Country
U.S.A.
Belgium
France
Italy
Portugal
The Netherlands
New Zealand
Iceland
Setting
US
EU
FRA
EU
EU
EU
EU
EU
Country
Canada
Denmark
Germany
Ireland
Spain
United Kingdom
Switzerland
Hungary
Setting
US
EU
EU
EU
EU or ESP
EU
EU
EU
Country
Austria
Finland
Greece
Luxembourg
Sweden
Australia
Norway
Liechtenstein
Setting
EU
EU
EU
EU
EU
EU
EU
EU
7-17

Public link updated
The public link to your chat has been updated.
Advertisement