Trendnet TV-H400 Outdoor Camera Dome Enclosure Quick Installation Guide

Trendnet TV-H400 Outdoor Camera Dome Enclosure Quick Installation Guide | Manualzz

Quick Installation Guide

TV-H400

H/W: V1.0R

Table of Contents

English ...................................................................................................... 1

1. Before You Start ................................................................................

2. Hardware Installation .........................................................................

1

2

Troubleshooting ........................................................................................ 9

Version 07.10.2008

1. Before you start

Package Contents

Installation Requirements

The following items below are not included. Users must provide the items themselves. Make sure to have each item on hand before installation.

1

English

2. Hardware Installation

Note: Configure your Internet Camera Server to match your network before installing the device.

1. Rotate the TV-H400's cover counter clockwise and remove the cover.

2. Unscrew the thumbscrew to remove the protective plate from the wall mount. Save this screw.

You will need to use this screw later.

3. Run all necessary cables (CAT 5 cable, power adapter cable, and the power terminals) through the wall mount.

2

English

4. Run each cable through the opening located at the top of the

TV-H400. DO NOT run all cables through the opening simultaneously. Serious blockage can occur.

5. After inserting the appropriate cables, extend each cable to 6 inches for camera installation.

6. Use the provided rubber seal to seal the housing.

7. Slide the protective plating into the wall mount and tighten the thumb screw.

3

English

8. Screw the ceiling or wall mount on top of the TV-H400 with the provided Allen wrench and three hexagon socket screws. The screws are in the plastic bag labeled Q2 or Q2B.

9. Combine the 5cm Hex screws with the 1cm Hex screws. The 5cm

Hex screws are in the plastic bag labeled Q3. The 1cm Hex screws are in the plastic bag labeled Q4.

10. Take the circular base and connect the three Hex screws to create this assembly. Then secure the hex crews with the nuts. The nuts are in the plastic bag labeled Q5.

4

English

11. Mount the assembly in step 10 to the camera enclosure using the three flat head screws. These screws are in the plastic bag labeled Q1.

12. Mount this bracket on top of the three Hex screws, Then using the three round head screws to secure the bracket. These screws are in the plastic bag labeled Q6.

13. Connect the remaining two hex crews to this bracket.

5

English

14. Attach the mounting plate for the camera with 3 small screws.

These screws should come with the Internet Camera Server.

15. Take the assembly in step 14 and mount the assembly on top of the mounting bracket with two round head screws. These screws are in the plastic bag labeled Q6.

16. Connect the Ethernet cable and power adapter to the Internet

Camera Server.

6

English

17. Place the TV-H400's cover over the camera and rotate the cover clock-wise.

18. Connect the power terminal to the provided 12V DC, 0.6A power adapter.

19. Plug the power to the Internet

Camera Server and the camera enclosure into an available power outlet.

Your installation is now complete.

For detailed information regarding the TV-H400 configuration and advanced settings, please visit TRENDnet's website at www.trendnet.com

Register Your Product

To ensure the highest level of customer service and support, please take a moment to register your product Online at:

www.trendnet.com/register

Thank you for choosing TRENDnet

7

English

Mounting the Camera Enclosure

Note: Mounting screws and screw anchors are not included.

1. Place the mounting bracket against the wall or ceiling and mark each of the four holes with a pencil.

2. Drill holes for the screws at each marked position.

3. Insert screw anchors into the holes.

4. Align the wall or ceiling mount bracket with the screws, and then use nuts and washers to secure it.

8

English

Troubleshooting

Q1: After I put my Internet Camera Server in the enclosure, the image is distorted.

What should I do?

A1:

First, make sure that you have adjusted the focus on your camera. Second, mount the TV-H400 so that it's not in direct view of the sun.

If you still encounter problems or have any questions regarding the TV-H400, please contact TRENDnet's Technical Support Department.

9

Certifications

This equipment has been tested and found to comply with FCC and CE Rules.

Operation is subject to the following two conditions:

(1) This device may not cause harmful interference.

(2) This device must accept any interference received. Including interference that may cause undesired operation.

Waste electrical and electronic products must not be disposed of with household waste. Please recycle where facilities exist. Check with you Local

Authority or Retailer for recycling advice.

NOTE: THE MANUFACTURER IS NOT RESPONSIBLE FOR ANY RADIO OR TV

INTERFERENCE CAUSED BY UNAUTHORIZED MODIFICATIONS TO THIS

EQUIPMENT. SUCH MODIFICATIONS COULD VOID THE USER’S AUTHORITY TO

OPERATE THE EQUIPMENT.

ADVERTENCIA

En todos nuestros equipos se mencionan claramente las caracteristicas del adaptador de alimentacón necesario para su funcionamiento. El uso de un adaptador distinto al mencionado puede producir daños fisicos y/o daños al equipo conectado. El adaptador de alimentación debe operar con voltaje y frecuencia de la energia electrica domiciliaria existente en el pais o zona de instalación.

Product Warranty Registration

Please take a moment to register your product online.

Go to TRENDnet’s website at http://www.trendnet.com/register

20675 Manhattan Place

Torrance, CA 90501

USA

Copyright ©2008. All Rights Reserved. TRENDnet.

Was this manual useful for you? Yes No
Thank you for your participation!

* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project

Download PDF

advertisement