DeWalt DCF825 Impact driver Technical data

Add to My manuals
16 Pages

advertisement

DeWalt DCF825 Impact driver Technical data | Manualzz

DCF825

DCF895

3

2

Copyright D E WALT

Figure 1 d g c a j e f g k b h i g l i h i

Figure 2 e f m

1

Figure 3

Figure 5

Figure 4 j

Figure 6 d d c

2

ENGLISH

BRUSHLESS CORDLESS IMPACT DRIVERS

DCF825, DCF895

Congratulations!

You have chosen a D E WALT tool. Years of experience, thorough product development and innovation make D E WALT one of the most reliable partners for professional power tool users.

Technical Data

DCF825 DCF895

Type

Battery Type

No load speed

Impact rate

1/2/10/11

Li-Ion

1/2/10/11

Li-Ion rpm 0–900 0–950

0–1850 0–1900

0–2800 0–2850 ipm 0–1200 0–1300

0–2300 0–2400

0–3200 0–3300

Max torque

Tool holder

Nm 160

6.35 mm

(1/4")

Weight (without battery pack) kg 1.03

170

6.35 mm

(1/4")

1.03

Noise values and vibration values (triax vector sum) according to EN60745-2-2.

L

PA

(emission sound

pressure level)

L

WA

(sound power level)

K

WA

(uncertainty for the

given sound level) dB(A) 97 97 dB(A) 108 108 dB(A) 3 3

Vibration emission value a h

Uncertainty K =

= m/s² m/s²

22 22

3.2 3.2

The vibration emission level given in this information sheet has been measured in accordance with a standardised test given in EN 60745 and may be used to compare one tool with another. It may be used for a preliminary assessment of exposure.

WARNING: The declared vibration emission level represents the main applications of the tool. However if the tool is used for different applications, with different accessories or poorly maintained, the vibration emission may differ. This may significantly increase the exposure level over the total working period.

An estimation of the level of exposure to vibration should also take into account the times when the tool is switched off or when it is running but not actually doing the job. This may significantly reduce the exposure level over the total working period.

Identify additional safety measures to protect the operator from the effects of vibration such as: maintain the tool and the accessories, keep the hands warm, organisation of work patterns.

Voltage V

DC

Capacity A h

Weight kg 0.53 0.30

Voltage V

DC

Capacity A h

Weight kg 0.64 0.35

3

ENGLISH

Charger DCB105

Mains voltage V

AC

230

Battery type Li-Ion

Approximate min 25 30 40 charging time (1.3 Ah) (1.5 Ah) (2.0 Ah) of battery packs 55 70 90

(3.0 Ah) (4.0 Ah) (5.0 Ah)

NOTICE: Indicates a practice not

related to personal injury which, if not avoided, may result in property

damage.

Denotes risk of electric shock.

Denotes risk of fire.

EC-Declaration of Conformity

MACHINERY DIRECTIVE

Charger DCB107

Mains voltage V

AC

230

Battery type Li-Ion

Approximate min 60 70 90 charging time of battery packs

(1.3 Ah) (1.5 Ah) (2.0 Ah)

140 185 240

(3.0 Ah) (4.0 Ah) (5.0 Ah)

Charger DCB112

Mains voltage V

AC

230

Battery type Li-Ion

Approximate min 40 45 60 charging time (1.3 Ah) (1.5 Ah) (2.0 Ah) of battery packs 90 120 150

(3.0 Ah) (4.0 Ah) (5.0 Ah)

BRUSHLESS CORDLESS IMPACT DRIVERS

DCF825, DCF895

D E WALT declares that these products described under Technical Data are in compliance with:

2006/42/EC, EN 60745-1, EN 60745-2-2.

These products also comply with Directive

2004/108/EC (until 19.04.2016), 2014/30/EU (from

20.04.2016) and 2011/65/EU. For more information, please contact D E WALT at the following address or refer to the back of the manual.

The undersigned is responsible for compilation of the technical file and makes this declaration on behalf of

D E WALT.

4

Fuses

Europe

U.K. & Ireland

230 V tools

230 V tools

10 Amperes, mains

3 Amperes, in plugs

Defi nitions: Safety Guidelines

The definitions below describe the level of severity for each signal word. Please read the manual and pay attention to these symbols.

DANGER: Indicates an imminently hazardous situation which, if not avoided,

will result in death or serious injury.

WARNING: Indicates a potentially hazardous situation which, if not avoided, could result in death or

serious injury.

CAUTION: Indicates a potentially hazardous situation which, if not avoided, may result in minor or

moderate injury.

Horst Grossmann

Vice President Engineering

D E WALT, Richard-Klinger-Straße 11,

D-65510, Idstein, Germany

21.08.14

WARNING: To reduce the risk of injury, read the instruction manual.

General Power Tool Safety Warnings

WARNING! Read all safety warnings

and all instructions. Failure to follow the warnings and instructions may result in electric shock, fire and/or serious injury.

SAVE ALL WARNINGS AND INSTRUCTIONS

FOR FUTURE REFERENCE

The term “power tool” in the warnings refers to your mains-operated (corded) power tool or batteryoperated (cordless) power tool.

1) WORK AREA SAFETY a) Keep work area clean and well lit.

Cluttered or dark areas invite accidents.

b) Do not operate power tools in explosive atmospheres, such as in the presence of

flammable liquids, gases or dust. Power tools create sparks which may ignite the dust or fumes.

c) Keep children and bystanders away while

operating a power tool. Distractions can cause you to lose control.

2) ELECTRICAL SAFETY a) Power tool plugs must match the outlet.

Never modify the plug in any way. Do not use any adapter plugs with earthed

(grounded) power tools. Unmodified plugs and matching outlets will reduce risk of electric shock.

b) Avoid body contact with earthed or grounded surfaces such as pipes,

radiators, ranges and refrigerators. There is an increased risk of electric shock if your body is earthed or grounded.

c) Do not expose power tools to rain or wet

conditions. Water entering a power tool will increase the risk of electric shock.

d) Do not abuse the cord. Never use the cord for carrying, pulling or unplugging the power tool. Keep cord away from heat, oil, sharp edges or moving parts.

Damaged or entangled cords increase the risk of electric shock. e) When operating a power tool outdoors, use an extension cord suitable for outdoor

use. Use of a cord suitable for outdoor use reduces the risk of electric shock. f) If operating a power tool in a damp location is unavoidable, use a residual current device (RCD) protected supply.

Use of an RCD reduces the risk of electric shock.

3) PERSONAL SAFETY a) Stay alert, watch what you are doing and use common sense when operating a power tool. Do not use a power tool while you are tired or under the influence of

drugs, alcohol or medication. A moment of inattention while operating power tools may result in serious personal injury.

b) Use personal protective equipment.

Always wear eye protection. Protective equipment such as dust mask, non-skid safety shoes, hard hat, or hearing protection used for appropriate conditions will reduce personal injuries.

c) Prevent unintentional starting. Ensure the switch is in the off position before connecting to power source and/or

ENGLISH battery pack, picking up or carrying the

tool. Carrying power tools with your finger on the switch or energising power tools that have the switch on invites accidents.

d) Remove any adjusting key or wrench

before turning the power tool on. A wrench or a key left attached to a rotating part of the power tool may result in personal injury.

e) Do not overreach. Keep proper

footing and balance at all times. This enables better control of the power tool in unexpected situations.

f) Dress properly. Do not wear loose clothing or jewellery. Keep your hair, clothing and gloves away from moving

parts. Loose clothes, jewellery or long hair can be caught in moving parts. g) If devices are provided for the connection of dust extraction and collection facilities, ensure these are connected and properly

used. Use of dust collection can reduce dust-related hazards.

4) POWER TOOL USE AND CARE a) Do not force the power tool. Use the correct power tool for your application.

The correct power tool will do the job better and safer at the rate for which it was designed.

b) Do not use the power tool if the switch

does not turn it on and off. Any power tool that cannot be controlled with the switch is dangerous and must be repaired.

c) Disconnect the plug from the power source and/or the battery pack from the power tool before making any adjustments, changing accessories, or

storing power tools. Such preventive safety measures reduce the risk of starting the power tool accidentally.

d) Store idle power tools out of the reach of children and do not allow persons unfamiliar with the power tool or these instructions to operate the power tool.

Power tools are dangerous in the hands of untrained users.

e) Maintain power tools. Check for misalignment or binding of moving parts, breakage of parts and any other condition that may affect the power tool’s operation.

If damaged, have the power tool repaired

before use. Many accidents are caused by poorly maintained power tools.

f) Keep cutting tools sharp and clean.

Properly maintained cutting tools with sharp cutting edges are less likely to bind and are easier to control.

5

6

ENGLISH g) Use the power tool, accessories and tool bits etc., in accordance with these instructions taking into account the working conditions and the work to

be performed. Use of the power tool for operations different from those intended could result in a hazardous situation.

5) BATTERY TOOL USE AND CARE a) Recharge only with the charger specified

by the manufacturer. A charger that is suitable for one type of battery pack may create a risk of fire when used with another battery pack.

b) Use power tools only with specifically

designated battery packs. Use of any other battery packs may create a risk of injury and fire.

c) When battery pack is not in use, keep it away from other metal objects like paper clips, coins, keys, nails, screws or other small metal objects that can make a connection from one terminal to another.

Shorting the battery terminals together may cause burns or a fire.

d) Under abusive conditions, liquid may be ejected from the battery, avoid contact.

If contact accidentally occurs, flush with water. If liquid contacts eyes, additionally

seek medical help. Liquid ejected from the battery may cause irritation or burns.

6) SERVICE a) Have your power tool serviced by a qualified repair person using only identical

replacement parts. This will ensure that the safety of the power tool is maintained.

Additional Specifi c Safety Rules for

Impact Wrenches/Drivers

Hold power tool by insulated gripping surfaces when performing an operation where the fastener may contact hidden

wiring. Fasteners contacting a “live” wire may make exposed metal parts of the power tool

“live” and could give the operator an electric shock.

Residual Risks

In spite of the application of the relevant safety regulations and the implementation of safety devices, certain residual risks cannot be avoided.

These are:

– Impairment of hearing.

– Risk of personal injury due to flying particles.

– Risk of burns due to accessories becoming hot during operation.

– Risk of personal injury due to prolonged use.

Markings on Tool

The following pictograms are shown on the tool:

Read instruction manual before use.

DATE CODE POSITION

The date code, which also includes the year of manufacture, is printed into the housing surface that forms the mounting joint between tool and battery.

Example:

2015 XX XX

Year of Manufacture

Important Safety Instructions for All

Battery Chargers

SAVE THESE INSTRUCTIONS: This manual contains important safety and operating instruc tions for the DCB105, DCB107 and DCB112 battery chargers.

• Before using the charger, read all instructions and cautionary markings on charger, battery pack and product using the battery pack.

WARNING: Shock hazard. Do not allow any liquid to get inside charger. Electric shock may result.

WARNING: We recommend the use of a residual current device with a residual current rating of 30mA or less.

CAUTION: Burn hazard. To reduce the risk of injury, charge only D E WALT rechargeable battery packs. Other types of batteries may overheat and burst resulting in personal injury and property damage.

CAUTION: Children should be supervised to ensure that they do not play with the appliance.

NOTICE: Under certain conditions, with the charger plugged in to the power supply, the exposed charging contacts inside the charger can be shorted by foreign material. Foreign materials of a conductive nature such as, but not limited to, steel wool, aluminum foil or any buildup of metallic particles should be kept away from charger cavities.

Always unplug the charger from the power supply when there is no battery pack in the cavity. Unplug charger before attempting to clean.

• DO NOT attempt to charge the battery pack with any chargers other than the ones in

this manual. The charger and battery pack are specifically designed to work together.

• These chargers are not intended for any uses other than charging D E WALT

rechargeable batteries. Any other uses may result in risk of fire, electric shock or electrocution.

• Do not expose charger to rain or snow.

• Pull by plug rather than cord when

disconnecting charger. This will reduce risk of damage to electric plug and cord.

• Make sure that cord is located so that it will not be stepped on, tripped over or otherwise subjected to damage or stress.

• Do not use an extension cord unless it

is absolutely necessary. Use of improper extension cord could result in risk of fire, electric shock or electrocution.

When operating a charger outdoors, always provide a dry location and use an extension

cord suitable for outdoor use. Use of a cord suitable for outdoor use reduces the risk of electric shock.

• Do not block the ventilation slots on the charger. The ventilation slots are located

on the top and sides of the charger. Place the charger in a position away from any heat source.

• Do not operate charger with damaged cord

or plug — have them replaced immediately.

Do not operate charger if it has received a sharp blow, been dropped or otherwise

damaged in any way. Take it to an authorised service centre.

• Do not disassemble the charger; take it to an authorised service centre when service or

repair is required. Incorrect reassembly may result in a risk of electric shock, electrocution or fire.

• In case of damaged power supply cord the supply cord must be replaced immediately by the manufacturer, its service agent or similar qualified person to prevent any hazard.

• Disconnect the charger from the outlet before attempting any cleaning. This will

reduce the risk of electric shock. Removing the battery pack will not reduce this risk.

• NEVER attempt to connect 2 chargers together.

• The charger is designed to operate on standard 230 V household electrical power.

Do not attempt to use it on any other

voltage. This does not apply to the vehicular charger.

SAVE THESE INSTRUCTIONS

ENGLISH

Chargers

The DCB105, DCB107 and DCB112 chargers accept 10.8V, 14.4V and 18V XR Li-Ion (DCB123,

DCB125, DCB127, DCB140, DCB141, DCB142,

DCB143, DCB144, DCB145, DCB180, DCB181,

DCB182, DCB183, DCB184 and DCB185) battery packs.

These chargers require no adjustment and are designed to be as easy as possible to operate.

Charging Procedure (fi g. 2)

1. Plug the charger into an appropriate outlet before inserting battery pack.

2. Insert the battery pack (f) into the charger, making sure the pack is fully seated in the charger. The red (charging) light will blink continuously indicating that the charging process has started.

3. The completion of charge will be indicated by the red light remaining ON continuously. The pack is fully charged and may be used at this time or left in the charger.

NOTE: To ensure maximum performance and life of

Li-Ion batteries, charge the battery pack fully before first use.

Charging Process

Refer to the table below for the charge status of the battery pack.

Charge indicators: DCB105 charging –– –– –– –– –– –– –– fully charged –––––––––––––––––––– hot/cold pack delay ––– • ––– • ––– • ––– x replace battery pack • • • • • • • • • • • • • •

Charge indicators: DCB107, DCB112 charging –– –– –– –– –– fully charged –––––––––––––– hot/cold pack delay*

–– –– –– –––––

* DCB107, DCB112: The red light will continue to blink, but a yellow indicator light will be illuminated during this operation. Once the battery has reached an appropriate temperature, the yellow light will turn off and the charger will resume the charging procedure.

The compatible charger(s) will not charge a faulty battery pack. The charger will indicate faulty battery

7

8

ENGLISH by refusing to light or by displaying problem pack or charger blink pattern.

NOTE: This could also mean a problem with a charger.

If the charger indicates a problem, take the charger and battery pack to be tested at an authorised service centre.

HOT/COLD PACK DELAY

When the charger detects a battery that is too hot or too cold, it automatically starts a Hot/Cold Pack

Delay, suspending charging until the battery has reached an appropriate temperature. The charger then automatically switches to the pack charging mode. This feature ensures maximum battery life.

A cold battery pack will charge at about half the rate of a warm battery pack. The battery pack will charge at that slower rate throughout the entire charging cycle and will not return to maximum charge rate even if the battery warms.

LITHIUM ION BATTERY PACKS ONLY

XR Li-Ion tools are designed with an Electronic

Protection System that will protect the battery against overloading, overheating or deep discharge.

The tool will automatically turn off if the Electronic

Protection System engages. If this occurs, place the

Li-Ion battery on the charger until it is fully charged.

Important Safety Instructions for All

Battery Packs

When ordering replacement battery packs, be sure to include the catalog number and voltage.

The battery pack is not fully charged out of the carton. Before using the battery pack and charger, read the safety instructions below and then follow the charging procedures outlined.

READ ALL INSTRUCTIONS

• Do not charge or use the battery pack in explosive atmospheres, such as in the presence of flammable liquids, gases or

dust. Inserting or removing the battery pack from the charger may ignite the dust or fumes.

• Never force the battery pack into charger.

Do not modify the battery pack in any way to fit into a non-compatible charger as battery pack may rupture causing serious

personal injury.

• Charge the battery packs only in designated

D E WALT chargers.

• DO NOT splash or immerse in water or other liquids.

• Do not store or use the tool and battery pack in locations where the temperature may reach or exceed 40 °C (105 °F) (such as outside sheds or metal buildings in summer).

• For best results, make sure the battery pack is fully charged before use.

WARNING: Never attempt to open the battery pack for any reason. If the battery pack case is cracked or damaged, do not insert it into the charger. Do not crush, drop or damage battery pack. Do not use a battery pack or charger that has received a sharp blow, been dropped, run over or damaged in any way (e.g., pierced with a nail, hit with a hammer, stepped on). Electric shock or electrocution may result. Damaged battery packs should be returned to the service centre for recycling.

CAUTION: When not in use, place tool on its side on a stable surface where it will not cause a tripping or

falling hazard. Some tools with large battery packs will stand upright on the battery pack but may be easily knocked over.

SPECIFIC SAFETY INSTRUCTIONS FOR LITHIUM ION

(Li-Ion)

• Do not incinerate the battery pack even if it is severely damaged or is completely worn

out. The battery pack can explode in a fire.

Toxic fumes and materials are created when lithium ion battery packs are burned.

• If battery contents come into contact with the skin, immediately wash the area with

mild soap and water. If the battery liquid gets into the eye, rinse water over the open eye for

15 minutes or until irritation ceases. If medical attention is needed, the battery electrolyte is composed of a mixture of liquid organic carbonates and lithium salts.

• Contents of opened battery cells may cause

respiratory irritation. Provide fresh air. If symptoms persists, seek medical attention.

WARNING: Burn hazard. Battery liquid may be flammable if exposed to spark or flame.

Battery Pack

BATTERY TYPE

The DCF825 operates on 14.4 volt battery packs.

The DCF895 operates on 18 volt battery pack.

ENGLISH

The DCB140, DCB141, DCB142, DCB143, DCB144,

DCB145, DCB180, DCB181, DCB182, DCB183,

DCB184 or DCB185 battery packs may be used.

Refer to Technical Data for more information.

Storage Recommendations

1. The best storage place is one that is cool and dry away from direct sunlight and excess heat or cold. For optimum battery performance and life, store battery packs at room temperature when not in use.

2. For long storage, it is recommended to store a fully charged battery pack in a cool, dry place out of the charger for optimal results.

NOTE: Battery packs should not be stored completely depleted of charge. The battery pack will need to be recharged before use.

Labels on Charger and Battery Pack

In addition to the pictographs used in this manual, the labels on the charger and the battery pack show the following pictographs:

Read instruction manual before use.

See Technical Data for charging time.

Battery charging.

Battery charged.

Battery defective.

Hot/cold pack delay.

Do not probe with conductive objects.

Do not charge damaged battery packs.

Do not expose to water.

Discard the battery pack with due care for the environment.

Charge D E WALT battery packs only with designated D E WALT chargers. Charging battery packs other than the designated

D E WALT batteries with a D E WALT charger may make them burst or lead to other dangerous situations.

Do not incinerate the battery pack.

Package Contents

The package contains:

1 Impact driver

1 Charger

2 Li-Ion battery packs (M2, P2 models)

3 Li-Ion battery packs (M3, P3 models)

1 Li-Ion battery pack (M1, P1 models)

1 Magnetic bit holder

1 Belt hook

1 Kitbox

1 Instruction manual

NOTE: Battery packs, chargers and kitboxes are not included with N-models.

• Check for damage to the tool, parts or accessories which may have occurred during transport.

• Take the time to thoroughly read and understand this manual prior to operation.

Description (fi g. 1, 2)

WARNING: Never modify the power tool or any part of it. Damage or personal injury could result.

a. Trigger switch

b. Forward/reverse control button

c. Accessory release button

d. 6.35 mm (1/4") hex chuck

e. Battery release button

Have defective cords replaced immediately.

g. Worklights

h. Belt hook

Charge only between 4 ˚C and 40 ˚C.

Only for indoor use.

l. Magnetic bit holder

9

ENGLISH

INTENDED USE

These impact wrench/drivers are designed for professional impact screwdriving applications. The impact function makes this tool particularly useful for driving fasteners in wood, metal and concrete.

DO NOT use under wet conditions or in presence of flammable liquids or gases.

These impact wrench/drivers are professional power tools.

DO NOT let children come into contact with the tool. Supervision is required when inexperienced operators use this tool.

Young children and the infirm. This appliance is not intended for use by young children or infirm persons without supervision.

• This product is not intended for use by persons

(including children) suffering from diminished physical, sensory or mental abilities, or for lack of experience and/or for want of knowledge or skills unless they are supervised by a person responsible for their safety. Children should never be left alone to play with this product.

Electrical Safety

The electric motor has been designed for one voltage only. Always check that the battery pack voltage corresponds to the voltage on the rating plate. Also make sure that the voltage of your charger corresponds to that of your mains.

Your D E WALT charger is double insulated in accordance with EN 60335; therefore no earth wire is required.

If the supply cord is damaged, it must be replaced by a specially prepared cord available through the

D E WALT service organisation.

Mains Plug Replacement

(U.K. & Ireland Only)

If a new mains plug needs to be fitted:

• Safely dispose of the old plug.

• Connect the brown lead to the live terminal in the plug.

• Connect the blue lead to the neutral terminal.

WARNING: No connection is to be made to the earth terminal.

Follow the fitting instructions supplied with good quality plugs. Recommended fuse: 3 A.

Using an Extension Cable

An extension cord should not be used unless absolutely necessary. Use an approved extension cable suitable for the power input of your charger

(see Technical Data). The minimum conductor size is 1 mm 2 ; the maximum length is 30 m.

When using a cable reel, always unwind the cable completely.

ASSEMBLY AND ADJUSTMENTS

WARNING: Prior to assembly and adjustment, always remove the battery pack. Always switch off the tool before inserting or removing the battery pack.

WARNING: Use only D E WALT battery packs and chargers.

Inserting and Removing the

Battery Pack from the Tool (fi g. 2)

NOTE: For best results, make sure your battery pack is fully charged.

TO INSTALL THE BATTERY PACK INTO THE TOOL HANDLE

1. Align the battery pack (f) with the rails inside the tool’s handle (fig. 2).

2. Slide it into the handle until the battery pack is firmly seated in the tool and ensure that it does not disengage.

TO REMOVE THE BATTERY PACK FROM THE TOOL

1. Press the battery release button (e) and firmly pull the battery pack out of the tool handle.

2. Insert battery pack into the charger as described in the charger section of this manual.

FUEL GAUGE BATTERY PACKS (FIG. 2)

Some D E WALT battery packs include a fuel gauge which consists of three green LED lights that indicate the level of charge remaining in the battery pack.

To actuate the fuel gauge, press and hold the fuel gauge button (m). A combination of the three green

LED lights will illuminate designating the level of charge left. When the level of charge in the battery is below the usable limit, the fuel gauge will not illuminate and the battery will need to be recharged.

NOTE: The fuel gauge is only an indication of the charge left on the battery pack. It does not indicate tool functionality and is subject to variation based on product components, temperature and end-user application.

Belt Hook and Magnetic Bit Holder

(fi g. 1)

WARNING: To reduce the risk of serious personal injury, turn tool off and disconnect battery pack

10

before making any adjustments or removing/installing attachments or accessories.

WARNING: To reduce the risk of serious personal injury, DO NOT suspend tool overhead or suspend objects from the belt hook. ONLY hang tool’s belt hook from a work belt.

WARNING: To reduce the risk of

serious personal injury, ensure the screw holding the belt hook is secure.

IMPORTANT: When attaching or replacing the belt hook or magnetic bit holder, use only the screw

(i) that is provided. Be sure to securely tighten the screw.

The belt hook (h) and magnetic bit holder (l) can be attached to either side of the tool using only the screw (i) provided, to accommodate left- or right- handed users. If the hook or magnetic bit holder is not desired at all, it can be removed from the tool.

To move belt hook or magnetic bit holder, remove the screw (i) that holds it in place then reassemble on the opposite side. Be sure to securely tighten the screw.

OPERATION

Instructions for Use

WARNING: Always observe the safety instructions and applicable regulations.

WARNING: To reduce the risk of serious personal injury, place the forward/reverse button in the lock-off position or turn tool off and disconnect battery pack before making any adjustments or removing/installing attachments or accessories.

Proper Hand Position (fi g. 1, 3)

WARNING: To reduce the risk of serious personal injury, ALWAYS use proper hand position as shown.

WARNING: To reduce the risk of serious personal injury, ALWAYS hold securely in anticipation of a sudden reaction.

Proper hand position requires one hand on the main handle (k).

Variable Speed Trigger Switch (fi g. 1)

To turn the tool on, squeeze the trigger switch (a). To turn the tool off, release the trigger switch. Your tool

ENGLISH is equipped with a brake. The tool will stop when the trigger switch is fully released.

The variable speed switch enables you to start the application at a slow speed. The further you squeeze the trigger, the faster the tool will operate.

For maximum tool life, use variable speed only for starting holes or fasteners.

NOTE: Continuous use in variable speed range is not recommended. It may damage the switch and should be avoided.

Forward/Reverse Control Button

(fi g. 1)

A forward/reverse control button (b) determines the direction of the tool and also serves as a lock-off button.

To select forward rotation, release the trigger switch and depress the forward/reverse control button on the right side of the tool.

To select reverse, release the trigger switch (a) and depress the forward/reverse control button on the left side of the tool. The center position of the control button locks the trigger switch (a) in the off position.

When changing the position of the control button, be sure the trigger is released.

NOTE: The first time the tool is run after changing the direction of rotation, you may hear a click on start up.

This is normal and does not indicate a problem.

Worklights (fi g. 1)

There are three worklights (g) located around the

6.35 mm (1/4") hex chuck (d). The worklights are activated when the trigger switch is depressed.

When the trigger is released, the worklight will stay illuminated for up to 20 seconds.

NOTE: The worklights are for lighting the immediate work surface and are not intended to be used as a flashlight.

Speed Selector (fi g. 1, 4)

Your tool is equipped with a speed selector (j) which allows you to select one of three speeds. Select the speed based on the application and control the speed of the tool using the variable speed trigger switch (a).

DCF825

Speed 1 rpm 0–900

Speed 2 rpm 0–1850

Speed 3 rpm 0–2800

DECF895

0–950

0–1900

0–2850

11

ENGLISH

Accessory Insertion and Release

(fi g. 1, 5, 6)

NOTE: These tools only accept 6.35 mm (1/4") hex accessories.

To install an accessory, fully insert the accessory into the chuck (d). The accessory is locked into place

(fig. 5).

To remove an accessory, push on the accessory release button (c). Remove the accessory then release the accessory release button (fig. 6).

Usage

Your impact tool generates the following maximum torque:

Cat #

DCF825

Nm

160

DCF895 170

CAUTION: Ensure fastener and/or system will withstand the level of torque generated by the tool. Excessive torque may cause breakage and possible personal injury.

1. Place the socket on the fastener head. Keep the tool pointed straight at the fastener.

2. Press switch to start operation. Release the switch to stop operation. Always check torque with a torque wrench, as the fastening torque is affected by many factors including the following:

Voltage: Low voltage, due to a nearly discharged battery, will reduce fastening torque.

Socket size: Failure to use the correct socket size will cause a reduction in fastening torque.

Bolt Size: Larger bolt diameters generally require higher fastening torque. Fastening torque will also vary according to length, grade, and torque coefficient.

Bolt: Ensure that all threads are free of rust and other debris to allow proper fastening torque.

Material: The type of material and surface finish of the material will affect fastening torque.

Fastening Time: Longer fasten ing time results in increased fastening torque. Using a longer fastening time than recommended could cause the fasteners to be overstressed, stripped or damaged.

MAINTENANCE

Your D E WALT power tool has been designed to operate over a long period of time with a minimum of maintenance. Continuous satisfactory operation depends upon proper tool care and regular cleaning.

WARNING: To reduce the risk of serious personal injury, place the forward/reverse button in the lock-off position or turn tool off and disconnect battery pack before making any adjustments or removing/installing attachments or accessories.

The charger and battery pack are not serviceable.

There are no serviceable parts inside.

Lubrication

Your power tool requires no additional lubrication.

Cleaning

WARNING: Blow dirt and dust out of the main housing with dry air as often as dirt is seen collecting in and around the air vents. Wear approved eye protection and approved dust mask when performing this procedure.

WARNING: Never use solvents or other harsh chemicals for cleaning the non-metallic parts of the tool. These chemicals may weaken the materials used in these parts. Use a cloth dampened only with water and mild soap. Never let any liquid get inside the tool; never immerse any part of the tool into a liquid.

CHARGER CLEANING INSTRUCTIONS

WARNING: Shock hazard. Disconnect the charger from the AC outlet before cleaning. Dirt and grease may be removed from the exterior of the charger using a cloth or soft non-metallic brush.

Do not use water or any cleaning solutions.

12

ENGLISH

Optional Accessories

WARNING: Since accessories, other than those offered by D E WALT, have not been tested with this product, use of such accessories with this tool could be hazardous. To reduce the risk of injury, only D E WALT recommended accessories should be used with this product.

WARNING: To reduce the risk of injury, only use D E WALT impact-ready accessories.

Consult your dealer for further information on the appropriate accessories.

Protecting the Environment

Separate collection. This product must not be disposed of with normal household waste.

Rechargeable Battery Pack

This long life battery pack must be recharged when it fails to produce sufficient power on jobs which were easily done before. At the end of its technical life, discard it with due care for our environment:

• Run the battery pack down completely, then remove it from the tool.

• Li-Ion cells are recyclable. Take them to your dealer or a local recycling station. The collected battery packs will be recycled or disposed of properly.

Should you find one day that your D E WALT product needs replacement, or if it is of no further use to you, do not dispose of it with household waste. Make this product available for separate collection.

Separate collection of used products and packaging allows materials to be recycled and used again. Re-use of recycled materials helps prevent environmental pollution and reduces the demand for raw materials.

Local regulations may provide for separate collection of electrical products from the household, at municipal waste sites or by the retailer when you purchase a new product.

D E WALT provides a facility for the collection and recycling of D E WALT products once they have reached the end of their working life. To take advantage of this service please return your product to any authorised repair agent who will collect them on our behalf.

You can check the location of your nearest authorised repair agent by contacting your local

D E WALT office at the address indicated in this manual. Alternatively, a list of authorised D E WALT repair agents and full details of our after-sales service and contacts are available on the Internet at:

www.2helpU.com.

13

Belgique et

Luxembourg België en Luxemburg

Danmark

Deutschland

Ελλάς

España

France

Schweiz

Suisse

Svizzera

Ireland

Italia

D E WALT - Belgium BVBA

Egide Walschaertsstraat 16

2800 Mechelen

D E WALT

Roskildevej 22

2620 Albertslund

Tel: NL 32 15 47 37 63

Tel: FR 32 15 47 37 64

Fax: 32 15 47 37 99

Tel: 70 20 15 10

Fax: 70 22 49 10

D E WALT

Richard Klinger Str. 11

65510 Idstein

Tel: 06126-21-1

Fax: 06126-21-2770

D

E

WALT (Ελλάς) Α.Ε.

EΔΡΑ-ΓΡΑΦΕΙΑ : Στράβωνος 7

& Λ. Βουλιαγμένης, Γλυφάδα 166 74, Αθήνα

SERVICE : Ημερος Τόπος 2 (Χάνι Αδάμ) –

193 00 Ασπρόπυργος

Τηλ: 00302108981616

Φαξ: 00302108983570

D E WALT Ibérica, S.C.A.

Parc de Negocios “Mas Blau”

Edificio Muntadas, c/Bergadá, 1, Of. A6

08820 El Prat de Llobregat (Barcelona)

D

E

WALT

5, allée des Hêtres

BP 30084, 69579 Limonest Cedex

Tel: 934 797 400

Fax: 934 797 419

Tel: 04 72 20 39 20

Fax: 04 72 20 39 00

Tel: 044 - 755 60 70

Fax: 044 - 730 70 67

D E WALT

In der Luberzen 42

8902 Urdorf

D E WALT

Calpe House Rock Hill

Black Rock, Co. Dublin

D E WALT via Energypark

20871 Vimercate (MB), IT

Tel: 00353-2781800

Fax: 00353-2781811

Tel: 800-014353

39 039 9590200

Fax: 39 039 9590313

Nederlands

Norge

Österreich

Portugal

Suomi

D E WALT Netherlands BV

Holtum Noordweg 35

6121 RE BORN, Postbus 83, 6120 AB BORN

Tel: 31 164 283 063

Fax: 31 164 283 200

D E WALT

Postboks 4613, Nydalen

0405 Oslo

D E WALT

Werkzeug Vertriebsges m.b.H

Oberlaaerstrasse 248, A-1230 Wien

Tel: 45 25 13 00

Fax: 45 25 08 00

Tel: 01 - 66116 - 0

Fax: 01 - 66116 - 614

D E WALT Limited, SARL

Centro de Escritórios de Sintra Avenida

Almirante Gago Coutinho, 132/134, Edifício 14

2710-418 Sintra

Tel: 214 66 75 00

Fax: 214 66 75 80

D E WALT

PL 47

00521 Helsinki

Puh: 010 400 4333

Faksi: 0800 411 340

Tel: 031 68 61 60

Fax: 031 68 60 08

Sverige

Türkiye

D E WALT

Box 94

431 22 Mölndal

KALE Hırdavat ve Makina A.Ş.

Defterdar Mah. Savaklar Cad. No:15

Edirnekapı / Eyüp / İSTANBUL 34050

TÜRKİYE

United

Kingdom

Australia

D E WALT, 210 Bath Road;

Slough, Berks SL1 3YD

D

E

WALT

82 Taryn Drive, Epping

VIC 3076 Australia

Middle East Africa D

E

WALT

P.O. Box - 17164,

Jebel Ali Free Zone (South), Dubai, UAE

Tel: 0212 533 52 55

Faks: 0212 533 10 05

Tel: 01753-567055

Fax: 01753-572112

Tel: Aust 1800 338 002

Tel: NZ 0800 339 258

Tel: 971 4 812 7400

Fax: 971 4 2822765

N387146 www.dewalt.be

[email protected]

www.dewalt.dk

[email protected]

www.dewalt.de

[email protected]

www.dewalt.gr

[email protected]

www.dewalt.es

[email protected]

www.dewalt.fr

[email protected]

www.dewalt.ch

[email protected]

www.dewalt.ie

www.dewalt.it

www.dewalt.nl

www.dewalt.no

[email protected]

www.dewalt.at

[email protected]

www.dewalt.pt

[email protected]

www.dewalt.fi

[email protected]

www.dewalt.se

[email protected]

www.dewalt.com.tr

www.dewalt.co.uk

[email protected]

www.dewalt.com.au www.dewalt.co.nz

www.dewalt.ae

[email protected]

01/15

advertisement

Related manuals

Download PDF

advertisement