ifs vtvr72430-2drdt-r3 install & oper instr

ifs vtvr72430-2drdt-r3 install & oper instr
VT72430-2DRDT-R3
VR72430-2DRDT-R3
IFS Fiber Module
Installation & Operation
Instructions
P/N 1062780 • REV B • ISS 01AUG11
VT/VR72430 -2DRDT
OFF
RS232 DATA
ON
1
ON
OFF
RS422 DATA
ON
2-WIRE
RS485 DATA
1
ON
1
2
2
ON
1
ON
Data Input
Data Output
Ground
OFF
OFF
ON
4-WIRE
RS485 DATA
2
7
6
5
4
3
2
1
2
ON
7
6
5
4
3
2
1
- Data In
+ Data In
7
6
5
4
3
2
1
- Data In/Out
+ Data In/Out
7
6
5
4
3
2
1
- Data Out
+ Data Out
NOTE: A 120 ohm resistor (provided)
may need to be connected across
the data lines to ensure proper
operation.
- Data In
+ Data In
- Data Out
+ Data Out
NOTE: A 120 ohm resistor (provided)
may need to be connected across
the data (IN) lines to ensure proper
operation.
VT7800A-2DRDT
8 CHANNEL DIGITAL VIDEO TRANSMITTER
+
2 CHANNEL DATA TRANSCEIVER
VT7800B
8 CHANNEL
DIGITAL VIDEO TRANSMITTER
ifs
ifs
VIDEO STATUS
A
B
POWER
VT7800C
8 CHANNEL
DIGITAL VIDEO TRANSMITTER
ifs
ifs
VIDEO STATUS
VIDEO STATUS
CHAN 1
CHAN 5
CHAN 9
CHAN 13
CHAN 17
CHAN 21
CHAN 2
CHAN 6
CHAN 10
CHAN 14
CHAN 18
CHAN 22
CHAN 3
CHAN 7
CHAN 4
CHAN 8
POWER
VT72430-2DRDT
CHAN 11
CHAN 15
CHAN 12
CHAN 16
VT72430-2DRDT
POWER
CHAN 19
CHAN 23
CHAN 20
CHAN 24
A
B
C
ifs
CH 1
C
CH 5
VR
RX
VT
VT
TX
VR
VT
VT
CH 4
POWER
CH 7
VR
VR
VT
VT
CH 8
VR
CH 9
B
RX
CH 11
TX
OPTICAL
CARRIER
1
2
OFF
VR
VR72430-2DRDT
ifs
VT
CH 12
POWER
VT
VR
VT
VT
CH 14
VR
VR
VT
VT
CH 15
VR
VR
VT
VT
CH 16
VR
VR72430-2DRDT
CH 17
CH 18
CH 19
OPTICAL
CARRIER
CH 20
POWER
VR
CWDM1X5
VT
CH 21
VR
VR
VT
VT
CH 22
VR
VR
VT
VT
CH 23
VR
VR
VT
VT
CH 24
VR
VR
VR72430-2DRDT
NOTE: WITHOUT PROPER FIBER CONNECTION, LED's DO NOT INDICATE
CORRECT OPERATIONAL STATUS OF THE UNIT.
International
Fiber
Systems
Incorporated
ifs
Status indicating
LEDs will change
from RED to GREEN
with these conditions.
Video detected from the transmitter
VIDEO STATUS
CH 13
ifs
Power
ifs
VT
VR
POWER
Video input from a camera
VR7800C
8 CHANNEL
DIGITAL VIDEO RECEIVER
VIDEO STATUS
CH 10
CH 6
VR
CH 3
OPTICAL
CARRIER
1
2
VT
VR
CH 2
ifs
A
OFF
VIDEO STATUS
VT
VR7800B
8 CHANNEL
DIGITAL VIDEO RECEIVER
115VAC - 1A 50/60HZ
220VAC - 1/2A 50/60HZ
VT72430-2DRDT
CWDM1X5
Simplex Single
Mode Fiber
Optic Cable
VR7800AX
8 CHANNEL DIGITAL VIDEO RECEIVER
+
2 CHANNEL DATA TRANSCEIVER
PS-R3
POWER SUPPLY
PS-R3
POWER SUPPLY
115VAC - 1A 50/60HZ
220VAC - 1/2A 50/60HZ
POWER
ifs
International
Fiber
Systems
Incorporated
ifs
FCC Compliance
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions: (1) This device may not cause harmful interference, and (2) this device must accept
any interference received, including interference that may cause undesirable operation.
Changes or modifications not expressly approved by International Fiber Systems, Inc. could void
the user’s authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class A
digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference when the equipment is operated in a
commercial environment. This equipment generates, uses and can radiate radio frequency
energy and, if not installed and used in accordance with the instruction manual, may cause
harmful interference to radio communications. Operation of this equipment in a residential
area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense.
CLASS 1 LASER PRODUCT
(For purposes of IEC 60825-1)
Complies with FDA Performance Standard for Laser Products
Title 21
Code of Federal Regulations
Subchapter J
Comprehensive
Lifetime Warranty
(a) Seller warrants to the original End User that products and any
services furnished hereunder will be free from defects in material
and workmanship as of the date of delivery, and will conform to
Seller’s published technical specifications. The foregoing shall
apply only to failures to meet said warranties which appear within
that period of time during which the Products are installed in their
original installation for the original End User and operator of such
Products; provided, however, that in the event of product discontinuance, warranty support is limited to five (5) years from the
announcement of discontinuance. Notwithstanding the preceding
sentence, the duration of the warranty period for products not
manufactured by Seller (e.g., fiber optic cabling, test equipment,
power supplies or batteries) shall be the warranty period offered by
the original manufacturer, if any.
(b) The conditions of any tests shall be mutually agreed upon and
Seller shall be notified of, and may be represented at, all tests that
may be made. The warranties and remedies set forth herein are
conditioned upon (a) proper storage, installation, use and maintenance, and conformance with any applicable recommendations of
Seller and (b) Buyer promptly notifying Seller of any defects and,
if required, promptly making the product available for correction.
(c) If any product or service fails to meet the foregoing warranties,
Seller shall thereupon correct any such failure either at its option,
(i) by repairing any defective or damaged product or parts of the
products, or (ii) by making available any necessary repaired or
replacement products or parts thereof. Any repaired or replacement
part or product shall be warranted for the remaining period of the
original Warranty Period. Seller shall pay, or credit Buyer for, the
cost of freight for all return shipments of products or parts to
Buyer. Where a failure cannot be corrected by Seller's reasonable
efforts, the parties will negotiate an equitable adjustment in price.
(d) The preceding paragraph sets forth the exclusive remedies for
claims based on defect in or failure of products or services,
whether the claim is in contract, indemnity, warranty, tort
(including Seller's negligence), strict liability or otherwise and
however instituted. Upon the expiration of the warranty period,
all such liability shall terminate and BUYER shall have a reasonable time, within thirty days after the warranty period, to give
written notice of any defects which appeared during the warranty
period. The foregoing warranties are exclusive and in lieu of all
other warranties, whether written, oral, implied or statutory.
NO IMPLIED OR STATUTORY WARRANTY OF
MERCHANTABILITY OR FITNESS FOR PARTICULAR
PURPOSE SHALL APPLY. Seller does not warrant any
products or services of others which BUYER has designated.
Contacting us
For help installing, operating, maintaining, and troubleshooting this product, refer to this document and any
other documentation provided. If you still have questions, contact us during business hours (Monday through
Friday, excluding holidays, between 5 a.m. and 5 p.m. Pacific Time).
Sales and support contact information
North
America
Toll-free: 855.286.8889 in the US, including Alaska and Hawaii;
Puerto Rico; Canada.
Outside the toll-free area: 503.885.5700.
E-mail: [email protected]
Europe
Select Contact Us at www.utcfssecurityproducts.eu
Australia
[email protected]
Note: Be ready at the equipment before calling.
Online
Another great resource for assistance with your Interlogix product is our online publication library. To access
the library, go to our website at the following location:
http://www.interlogix.com/transmission1
1.
Many Interlogix documents are provided as PDFs (portable document format). To read these documents, you will
need Adobe Reader, which can be downloaded free from Adobe’s website at www.adobe.com.
Product Disassembly Instructions for WEEE
Per European Directive 2002/95/EC Waste Electrical and
Electronic Equipment
Required Tools:
One number 2 Phillips (crosstip) screwdriver.
One number 2 flat screwdriver.
For the enclosed box version:
1. Locate and remove box cover securement screws. Usually, but not limited to, at least
4 screws.
2. Lift off box top cover.
3. Locate and remove securement screws for printed circuit board.
4. If there are multiple boards to the assembly, continue removing securement screws
until none are left.
5. Lift off printed circuit board.
6. Disassembly of box version of product is complete.
For rack version:
1. Locate and remove securement screws for printed circuit board. Usually, but not
limited to, at least 4 screws.
2. If there are multiple boards to the assembly, continue removing securement screws
until none are left.
3. Lift off printed circuit board(s).
4. Disassembly of rack card version of product is complete.
Copyright
Trademarks and
patents
Manufacturer
Certification
ACMA compliance
Canada
European Union
directives
© 2011 UTC Fire & Security. All rights reserved.
Interlogix and IFS names and logos are trademarks of
UTC Fire & Security.
Other trade names used in this document may be trademarks or
registered trademarks of the manufacturers or vendors of the
respective products.
UTC Fire & Security Americas Corporation, Inc.
2955 Red Hill Avenue, Costa Mesa, CA 92626-5923, USA
Authorized EU manufacturing representative:
UTC Fire & Security B.V.
Kelvinstraat 7, 6003 DH Weert, The Netherlands
N4131
Notice! This is a Class A product. In a domestic environment this
product may cause radio interference in which case the user may be
required to take adequate measures.
This Class A digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la classe A est conforme à la norme
NMB-003 du Canada.
2004/108/EC (EMC directive): Hereby, UTC Fire & Security
declares that this device is in compliance with the essential
requirements and other relevant provisions of Directive
2004/108/EC.
2002/96/EC (WEEE directive): Products marked with this symbol
cannot be disposed of as unsorted municipal waste in the European
Union. For proper recycling, return this product to your local supplier
upon the purchase of equivalent new equipment, or dispose of it at
designated collection points. For more information see:
www.recyclethis.info.
Contact information
For contact information, see www.interlogix.com.
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement