Clarke JET 9000 Maintenance Instruction

WARNING: Do not use the machine without reading this manual

POWER WASHER

MODEL NO: JET 8000

PART NO: 7333500

OPERATION & MAINTENANCE

INSTRUCTIONS

GC0913

INTRODUCTION

Thank you for purchasing this CLARKE Power Washer.

The machine has been designed to use hot or cold water to clean any surfaces which can stand the force of the high pressure water jet and the action of the detergents used.

The machine must only be used for the purpose for which it was designed.

Before attempting to use this product, please read this manual thoroughly and follow the instructions carefully. In doing so you will ensure the safety of yourself and that of others around you, and you can look forward to your purchase giving you long and satisfactory service.

GUARANTEE

This product is guaranteed against faulty manufacture for a period of 12 months from the date of purchase. Please keep your receipt which will be required as proof of purchase.

This guarantee is invalid if the product is found to have been abused or tampered with in any way, or not used for the purpose for which it was intended.

Faulty goods should be returned to their place of purchase, no product can be returned to us without prior permission.

This guarantee does not effect your statutory rights.

LIST OF CONTENTS

The following items should be supplied in the carton. If any parts are missing or damaged, please see your Clarke dealer where you purchased the machine.

1 x Power Washer

1 x Gun Assembly

1 x Lance c/w fitted Pencil-Jet / Fan - High / Low Nozzle

1 x Hose Assembly on integral Hose-Reel

1 x Inlet Hose Adaptor

1 x Instruction Manual

1 x Accessory Adaptor

2

Parts & Service: 020 8988 7400 / E-mail: [email protected] or [email protected]

GENERAL SAFETY RULES

WARNING: WATER AT HIGH PRESSURE CAN BE DANGEROUS AND CAN

CAUSE DAMAGE IF THE OPERATOR IS CARELESS. NEVER ALLOW ANYONE

TO OPERATE THIS MACHINE UNLESS THEY ARE FAMILIAR WITH THE SAFETY

PRECAUTIONS.

1. High pressure water jets can be dangerous if subject to misuse. They must not be directed at animals or people.

2. NEVER allow children or untrained personnel to use this product.

3. NEVER operate the power washer with any covers removed.

4. NEVER attempt any electrical or mechanical repairs to this power washer.

Always refer to your Clarke dealer.

5. NEVER supply any liquid other than water to the water inlet.

6. Never use the detergent facility to introduce flammable liquids/solvents, e.g. paint thinners, petrol, oil due to risk of explosion.

7. ALWAYS release any residual pressure in the machine by turning off the water supply and operating the trigger, before disconnecting the hose.

8. ALWAYS keep the pressure washer itself dry and clear of water spray.

9. Never direct the spray jet at the pressure washer itself or any other electrical equipment.

10. ALWAYS wear protective clothing, safety shoes and safety glasses. Loose particles & other debris may be propelled at high speed by the water jet.

11. ALWAYS hold the spray gun firmly & expect the gun to ‘kick’ when starting.

12. ALWAYS disconnect from the water supply and ensure the machine is completely drained when not in use. Store in a cool dry location.

13. Only use chemical cleaning agents (detergents), that are approved for pressure washers. CLARKE Traffic Film Remover or CLARKE Wash and Wax

(available from your dealer), are recommended.

14. ALWAYS disconnect from the electrical power supply and remove the plug from the socket before carrying out any maintenance.

15. O N LY u se o ri g i n al spa re pa rt s from the Clarke service department.

16. High pressure hoses, fittings and couplings are important for the safety of the m a c h i n e . U s e o n l y h o s e s , f i t t i n g s a n d co u p l i n g s r e c o m m e n d e d b y t h e manufacturer.

17. N E V E R u s e t h e p r e s s u r e w a s h e r i f t h e p o w e r c a b l e o r o t h e r i m p o r t a n t p a r t s o f t h e p o w e r w a s h e r a re damaged.

18. If an extension cable is used, the cable and plug must be of watertight construction. Inadequate extension cables can be dangerous.

3


SAFETY SYMBOLS

WARNING: Do not discharge the water spray at persons or animals. Keep clear of nozzle.

WARNING: Never direct spray toward any electrical device or electrical outlet.

Wear Gloves

Equipment covered by the European

WEE (Waste Electrical/Electronic)

Directive.

Read Instructions before use.

Wear Eye Protection

4


ELECTRICAL CONNECTIONS

WARNING: READ THESE ELECTRICAL SAFETY INSTRUCTIONS

THOROUGHLY BEFORE CONNECTING THE PRODUCT TO THE MAINS

SUPPLY.

Before switching the product on, make sure that the voltage of your electricity supply is the same as that indicated on the rating plate. This product is designed to operate on

230VAC 50Hz. Connecting it to any other power source may cause damage.

This product may be fitted with a non-rewireable plug. If it is necessary to change the fuse in the plug, the fuse cover must be refitted. If the fuse cover becomes lost or damaged, the plug must not be used until a suitable replacement is obtained.

If the plug has to be changed because it is not suitable for your socket, or due to damage, it should be cut off and a replacement fitted, following the wiring instructions shown below. The old plug must be disposed of safely, as insertion into a mains socket could cause an electrical hazard.

WARNING! The wires in the power cable of this product are coloured in accordance with the following code:

Blue = Neutral Brown = Live Yellow and Green = Earth

• The wire which is coloured Blue must be connected to the terminal which is marked N or coloured Black.

• The wire which is coloured Brown must be connected to the terminal which is marked L or coloured Red.

• The wire which is coloured Yellow and Green must be connected to the terminal which is marked E ( ) or coloured Green.

Plug must be BS1363/A approved.

Always fit a 13 Amp fuse.

Earth

(Green and Yellow)

Neutral

(Blue)

Live

(Brown)

Ensure that the outer sheath of the cable is firmly held by the clamp

WE STRONGLY RECOMMEND THAT THIS MACHINE IS CONNECTED TO THE MAINS SUPPLY VIA A

RESIDUAL CURRENT DEVICE (RCD)

If in any doubt, consult a qualified electrician. DO NOT attempt any repairs yourself.

5


OVERVIEW

1 Spray Gun Assembly

2 Telescopic Handle

3 High pressure Hose

4 Power Cable

5 Reel Handle

6 Detergent Container

7 Mains Water Inlet

8 On/OFF Switch

9 Lance

6


BEFORE USE

Unpack your power washer and check to ensure all the items listed on page 2 are present.

UNFOLDING THE HOSE REEL HANDLE

1. Open the reel handle from its folded position before use.

2. Release the hose from the retaining clip on the hose reel, then pull the hose from the reel to unwind whatever length is required.

• Winding the handle clockwise will reduce the length of the hose.

• If the spray gun/lance assembly is not attached, the hose can be secured in the retaining clip when the hose is re-wound.

USING THE CARRYING HANDLE

1. Press and hold the centre button on the telescopic handle to unlock it.

• This will enable the handle to extend and retract.

ASSEMBLING THE LANCE

The lance must be fitted to the gun assembly before use.

1. Assemble by screwing the end of the lance into the gun assembly.

2. Tighten the locking nut using a 22 mm spanner.

3. Slide the plastic cap into position.

7


CONNECTING THE GUN TO THE HOSE

Connect the gun to the hose by screwing on the connector and tightening with a 17 mm spanner.

CONNECTING THE MAINS WATER SUPPLY

NOTE: Always follow any regulations of your local water supplier.

1. Screw the inlet adaptor to the water inlet as shown.

2. Connect the mains water supply hose to the inlet adaptor. A standard garden hose is suitable.

• It is recommended to use a reinforced hose with an inner diameter of at least 10 mm available from your CLARKE dealer.

• Ensure the water connection is secure.

NOTE: The water source must provide a minimum of 6.6 litres per minute at not more than 40°C.

FILLING WITH DETERGENT

If you intend to use detergent:

1. Remove the detergent filler cap located at the rear of the pressure washer and fill with detergent.

• The detergent level should be visible through the window in the back of the machine. (max capacity 500ml)

2. Replace cap before use.

8


3. Only use detergents recommended for use with pressure washers, such as

CLARKE Traffic Film Remover which is a powerful ‘low foaming’ agent for car cleaning, patio cleaning etc., or CLARKE Wash & Wax, both available from your CLARKE dealer.

DESCRIPTION

Car Wash & Wax Shampoo

Concentrated Traffic Film Remover

Concentrated Traffic Film Remover

Ready To Use Traffic Film Remover

Ready To Use Traffic Film Remover

SIZE

5 Litre

5 Litre

25 Litre

5 Litre

25 Litre

PART NUMBER

3050815

3050821

3050820

3050818

3050819

• The use of unsuitable cleaning agents may adversely affect the safety of the machine. Before use, refer to correct operating temperatures on page 17.

ACCESSORIES

A range of accessories are available from your Clarke dealer including:

Accessories with bayonet style couplings such as those shown can be fitted to the hose by means of the adaptor supplied.

9


OPERATION

GETTING STARTED

1. Ensure that the water supply is correctly connected and turned on.

WARNING: FAILURE TO TURN ON THE WATER FULLY COULD CAUSE

DAMAGE TO THE POWER WASHER INTERNAL COMPONENTS.

WARNING: DO NOT USE THE POWER WASHER IF THE SUPPLY CABLE OR

IMPORTANT PARTS OF THE MACHINE ARE DAMAGED, E.G. SAFETY

DEVICES, HIGH PRESSURE HOSES, TRIGGER

WARNING: WE RECOMMEND THAT THIS MACHINE IS CONNECTED TO THE

MAINS SUPPLY VIA A RESIDUAL CURRENT DEVICE (RCD)

2. Plug the power cable into the mains supply.

3. Release the trigger lock.

• The pressure washer is now ready for use.

4. Press the start switch (‘I’).

5. Pull the trigger.

NOTE: When the trigger is pulled the pressure of water will cause the lance/gun assembly to kick back suddenly.

6. When using the power washer for the first time, let it run for a few moments so that any air bubbles or other impurities are discharged.

7. Release the trigger to stop the water flow.

• This pressure washer is fitted with an auto stop system to protect the motor during use.

• When the trigger is released, the motor will stop. When the trigger is squeezed the motor will start up again.

10


ADJUSTING THE SPRAY

The nozzle is adjustable to allow you to adjust the spray from a narrow jet of water to a wide spray.

To adjust the nozzle, proceed as follows:

1. Hold the shaft of the lance in one hand.

2. Twist the nozzle with the other hand.

3. To vary the spray between narrow and wide, turn the nozzle anticlockwise through 180 o .

ADJUSTING THE PRESSURE

There are three ways to adjust the pressure of the water:

1. Slide the nozzle forwards to lower the pressure.

2. Back away from the surface being cleaned. The further away you are the less the pressure will be on the surface being cleaned.

3. Adjust the spray to a wider angle.

APPLYING CHEMICALS AND CLEANING SOLVENTS

CAUTION: IF YOUR EYES COME INTO CONTACT WITH ANY CLEANING

FLUIDS, RINSE THEM IMMEDIATELY WITH PLENTY OF FRESH, CLEAN WATER

AND SEEK MEDICAL ADVICE IF REQUIRED.

1. Ensure the trigger is locked.

2. Remove the cap from the detergent container.

3. Fill the container with a suitable bio-degradable detergent.

4. Replace the cap.

5. Squeeze the trigger.

6. Pull the adjusting sleeve forward to set the required spray pressure.

7. Start washing.

11


SHUTTING DOWN

When you have finished using the power washer, follow the procedure below to switch off and disconnect the unit:

1. Press the stop switch (‘O’).

2. Turn the mains water supply off at the tap.

• NEVER turn the water off with the power washer running.

3. Release the pressure in the pump and hose by squeezing the trigger for a few seconds until no more water comes out of the nozzle.

4. Move the trigger lock to the locked position.

5. Disconnect the mains power supply and store the cable in its position on the rear of the machine.

6. Wind the hose onto the reel and store the spray gun/lance in the holder on the front of the power washer as shown on page 6.

12


MAINTENANCE

WARNING: THE MACHINE SHALL BE DISCONNECTED FROM THE POWER

SUPPLY BY REMOVING THE PLUG DURING CLEANING OR MAINTENANCE

AND WHEN REPLACING PARTS.

CLEANING THE NOZZLE

If the nozzle becomes partially clogged with foreign material such as dirt or limescale, excessive pressure may develop and the pump pressure will pulsate. Clean the nozzle immediately as follows:

1. Turn off the power washer and turn off the water supply.

2. Pull the trigger to relieve any water pressure.

3. Disconnect the lance from the spray gun.

4. Remove any obstructions by directing water supply into the end of the lance for 30 seconds to back flush loose particles.

5. Reconnect the lance to gun and turn on water supply.

REMOVING THE SPRAY GUN FROM THE HOSE

The gun can be disconnected from the hose for cleaning or to unblock the spray gun/hose by disconnecting the connection using a 17 mm spanner.

Pull the hose away from the spray gun.

CLEANING THE WATER INLET FILTER

This filter should be checked periodically and cleaned if necessary.

1. Remove filter from the water inlet of the pump as shown.

2. Clean the filter by flushing both sides with water.

3. Replace the filter into the water inlet.

• The tapered side faces inwards.

NOTE: Do not operate power washer without filter properly installed.

13


SERVICING

All repairs and maintenance operations must be carried out by technically qualified personnel while disconnected from the power and water supplies.

Correct use and maintenance is necessary to guarantee the power washer's reliability and best performance.

Please only use the correct spare parts as supplied by your Clarke dealer.

ANNUALLY

LIMESCALE

Periodically the pump should be checked for limescale buildup, dependant upon the hardness of the local water supply.

Please contact the CLARKE International Service Dept.

DE-COMMISSIONING THE PRODUCT

Should the product become completely unserviceable and require disposal, dispose of the product according to local regulations. Recycle unwanted materials instead of disposing of them as waste. All tools, accessories and packaging should be sorted, taken to a recycling centre and disposed of in a manner which is compatible with the environment.

STORING THE POWER WASHER

1. Disconnect the high pressure hose and drain all water from the hose.

2. Make sure that the power washer has been thoroughly cleaned before storing it in a clean dry place.

3. Avoid storing the power washer at freezing temperatures.

14


TROUBLESHOOTING

PROBLEM POSSIBLE CAUSE SOLUTION

No water delivery.

Low or irregular pressure

Water filter blocked.

Pump valves jammed.

Clogged lance nozzle.

Insufficient water supply.

Pump taking in air.

Detergent inlet sucking in air.

See cleaning the water filter on page 13.

Contact Clarke Service

Department.

Clean the nozzle.

Check connections.

Check connections.

Check connections and that detergent supply is topped up.

Water filter dirty.

Worn out gaskets or valve components.

Exceeding the inlet water temperature.

Damaged or warn out nozzle components.

Low Voltage.

Clean or replace.


Department for replacement.

Make sure the water supply is below 40 degrees.


Department for replacement.

Make sure the pressure washer is connected to a suitable power supply.

Machine is noisy.

Air intake worn out / dirty/ blocked valves. Excess water temperature.

Motor suddenly stops.

Thermal protection has activated due to overheating.

Pressure drop.

Check air inlet. Contact

Clarke Service Department.

Reduce water temperature.

Switch off the machine and wait until the unit has cooled down sufficiently.

Air in system .

Bleed system by quickly operating trigger several times. If necessary operate the machine briefly without the high pressure hose connected.

Worn high pressure nozzle .

Renew nozzle.

15


Pressure fluctuations or pressure drop.

Shortage of water.

No water due to clogged inlet filter.

Turn water tap on fully.

Water supply hose too long/ too narrow.

Use a 1/2” diameter water supply hose.

Clean water inlet filter.

Oil leak.

Motor does not start when switched on.

Worn seals.

Plug is not connected properly.

Contact your Clarke dealer.

Check plug and lead and have them replaced by a qualified electrician if necessary.

Mains fuse tripped/blown.

Renew fuse or reset.

Motor hums when trigger operated and does not start.

Mains voltage too low.

Incorrect diameter cable resulting in voltage drop.

Have electrical connection checked.

Use correct diameter cable.

Motor cuts out - trigger open.

Additives are not being supplied.

Pump seals stuck.

Motor protection switch has been activated due to overheating or motor overload.

Nozzle partly clogged.

Contact your Clarke dealer.

Ensure supply voltage and unit voltage are equal.

Switch off and allow to cool for at least three minutes.

Clean using the supplied nozzle cleaning needle.

Additive container empty.

Fill additive container.

Lance not correctly set.

Put lance on low pressure setting.

16


PRODUCT SPECIFICATIONS

Model Number

Part Number

Voltage

Motor Input Power

Duty Cycle

Working pressure

Maximum pump output pressure

Maximum output flow rate

Maximum output temperature

Maximum input temperature

JET 8000

7333500

230V/50Hz

2400 W

Continuous

108 bar

180 bar (2610 psi)

6.6 l/min (400 l/hr)

40 0 C (104 0 F)

0-40 0 C

Detergent tank capacity

Sound Pressure Level (L

WA

)

500 ml

78 dB

Sound power level (L

WA

) 91 dB

Guaranteed sound power level (L

WA

) 93 dB

Uncertainty Factor K 2.19

Vibration

Uncertainty Factor K

Dimensions (L x W x H)

Weight

1.0 m/s

0.15

280 x 348 x 640 mm

18.35 kg

CONSUMABLES

A range of suitable hose, shampoo and traffic film remover are available from your Clarke dealer.

17


PARTS LIST - FRAME & BODY

POS DESCRIPTION

8

9

10

11

12

13

14

15

6

7

4

5

1

2

3

CODE POS DESCRIPTION

Lance Holder

On/Off Switch

Front Cover

TMC8000FB01 16

TMC8000FB02 17

TMC8000FB03 18

Hose Reel Assembly TMC8000FB04 19

Left Clamp TMC8000FB05 20

Screw st 4.2 x 20

Rubber Grommet

TMC8000FB06

TMC8000FB07

21

22

Box Cover

Screw st 2.9 x 14

Pump Assembly

Wheel Cover Plate

Retaining Disc

Transport Wheel

Body Moulding

Telescopic Handle

TMC8000FB08

TMC8000FB09

TMC8000FB10

TMC8000FB

TMC8000FB12

23

24

25

26

27

TMC8000FB13 28

TMC8000FB14 29

TMC8000FB15 30

CODE

Top Cable Holder TMC8000FB16

Detergent Tank Plug TMC8000FB17

Lower Cable Holder TMC8000FB18

Bolt

Spring Washer

Flat Washer

Cable Protector

TMC8000FB19

TMC8000FB20

TMC8000FB21

TMC8000FB22

Copper E-Ring

Spring

Microswitch Conn.

Power Cable/Plug

Detergent Bottle

Cable Clamp

Left Clamp

Screw st 4.2 x 16

TMC8000FB23

TMC8000FB24

TMC8000FB25

TMC8000FB26

TMC8000FB27

TMC8000FB28

TMC8000FB29

TMC8000FB30

18


PARTS LIST - INTERNAL COMPONENTS

19


PARTS LIST - INTERNAL COMPONENTS

POS DESCRIPTION CODE POS DESCRIPTION CODE

1

2

Motor Cover

Capacitor (assy)

2-1 Connecting Cable

2-2 Insulating Sheath

2-3 E-Rings

2-4 Protecting Sheath

3 Connecting Wire

3-1 Connecting Wire

8

9

6

7

4

5

3-2 Spring

3-3 Earth Terminal

Motor Terminal

Screw

Screw

Terminal Cover

Induction Motor

Cam

TMC800001 22-2 Check Valve Spring

TMC800002 22-3 General Valve Core

TMC8000222

TMC8000223

TMC8000021 22-4 Seal Ring TMC8000224

TMC8000022 22-5 General Valve Cover TMC8000225

TMC8000023 23

TMC8000024 24

TMC800003 25

TMC8000031 26

Seal Ring

Filter Core

Compression Joint

Relief Valve

TMC800023

TMC800024

TMC800025

TMC800026

TMC8000032 26-1 Sealing Ring

TMC8000033 26-2 Relief Valve Piston

TMC800004 26-3 Relief Valve Support

TMC800005 26-4 Relief Valve Spring

TMC8000261

TMC8000262

TMC8000263

TMC8000264

TMC800006 26-5 Sealing Ring TMC8000265

TMC800007 26-6 Relief V. Coupling scr TMC8000266

TMC800008 26-7 Relief Valve Sheath

TMC800009 26-8 Safety Valve Stem

TMC8000267

TMC8000268

14

15

16

17

10

11

12

13

Spring Washer

Socket hd Screw

Thrust Bearing

Spring Cotter Pin

Plunger

Spring

O-Ring

Plunger Shelf

TMC800010 26-9 Auto stop Spring


TMC8000269

TMC80002610

TMC800012 26-11 Switch Box TMC80002611

TMC800013 26-12 Contact Breaker Assy TMC80002612

TMC800014 26-13 Switch Box Cover

TMC800015 26-14 Pressure Switch

TMC800016 26-15 Connecting Wires

TMC800017 26-16 Relief Valve Bonnet

TMC80002613

TMC80002614

TMC80002615

TMC80002616

18

19

20

21

Oil Seal

Guide band


TMC800019 26-18 Spring Comp.Ring

Y-section Water Seal TMC800020 26-19 Pedestal Cover

Check Valve Bolt TMC800021 26-20 Sealing Ring

21-1 Sealing Ring

21-2 Check Valve Bolt

TMC8000211 27 Check Valve

TMC8000212 27-1 Single Valve cap

22 General Valve TMC800022 27-2 Check Valve Core

22-1 Check Valve Support TMC8000221 28 Socket Head Plug

TMC80002617

TMC80002618

TMC80002619

TMC80002620

TMC800027

TMC8000271

TMC8000272

TMC800028

20


33

34

35

36

29

30

31

32

37

38

39

40

Socket Cap Screw

Socket Cap Screw

Plain Washer

Spring Washer

Socket Head Plug

Pump

Sealing Ring

Nozzle

TMC800029

TMC800030

TMC800031

TMC800032

TMC800033

TMC800034

TMC800035

TMC800036

41

42

43

44

45

46

46-1

46-2

Sealing Ring

Spring Gasket

Locking Washer

Oil Box Gasket

Screw

Inlet Connector

Inlet Conn. Gasket

Inlet Connector

Sealing Ring TMC800037 46-3 Sealing Ring

Compression Spring TMC800038 47 Sealing Ring

Steel Ball

Sealing Ring

TMC800039

TMC800040

48 Connector

TMC800041

TMC800042

TMC800043

TMC800044

TMC800045

TMC800046

TMC8000461

TMC8000462

TMC8000463

TMC800047

TMC800048

21


HOSE REEL & LANCE ASSEMBLIES

POS DESCRIPTION

5

6

7

3

4

1

2

8

CODE POS DESCRIPTION

Screw

Crank Handle

Bolt

Crank Handle

Hub

TMC8000HOSE01 10

TMC8000HOSE02 11

TMC8000HOSE03 12

TMC8000HOSE04 13

Cover

Screws

TMC8000HOSE05 14

TMC8000HOSE06 15

Hose Spool (right) TMC8000HOSE07 16

CODE

Seal Ring

Seal Ring

TMC8000HOSE10

TMC8000HOSE11

Hose Spool (left) TMC8000HOSE12

HP Hose Connector TMC8000HOSE13

Retaining Clip

Retaining Clip

TMC8000HOSE14

TMC8000HOSE15

PTFE Back Cushion

A

TMC8000HOSE16

PTFE Back Cushion B TMC8000HOSE17

9

High Pressure

Hose

TMC8000HOSE08 17

Hose Connector TMC8000HOSE09

POS DESCRIPTION

1 Lance Assy

2 Gun Assembly

CODE

TMCFQ301

TMCFQ302

POS DESCRIPTION

3 Adaptor

CODE

TMC8000ADAPTOR

22


DECLARATION OF CONFORMITY

23


Clarke JET 9000 Maintenance Instruction

POWER WASHER

MODEL NO: JET 8000

OPERATION & MAINTENANCE

INSTRUCTIONS

INTRODUCTION

GUARANTEE

LIST OF CONTENTS

GENERAL SAFETY RULES

SAFETY SYMBOLS

ELECTRICAL CONNECTIONS

Earth

Neutral

Live

OVERVIEW

BEFORE USE

UNFOLDING THE HOSE REEL HANDLE

USING THE CARRYING HANDLE

ASSEMBLING THE LANCE

CONNECTING THE GUN TO THE HOSE

CONNECTING THE MAINS WATER SUPPLY

FILLING WITH DETERGENT

ACCESSORIES

OPERATION

GETTING STARTED

ADJUSTING THE SPRAY

ADJUSTING THE PRESSURE

APPLYING CHEMICALS AND CLEANING SOLVENTS

SHUTTING DOWN

MAINTENANCE

CLEANING THE NOZZLE

REMOVING THE SPRAY GUN FROM THE HOSE

CLEANING THE WATER INLET FILTER

SERVICING

ANNUALLY

STORING THE POWER WASHER

TROUBLESHOOTING

PROBLEM POSSIBLE CAUSE SOLUTION

PRODUCT SPECIFICATIONS

CONSUMABLES

PARTS LIST - FRAME & BODY

PARTS LIST - INTERNAL COMPONENTS

PARTS LIST - INTERNAL COMPONENTS

HOSE REEL & LANCE ASSEMBLIES

DECLARATION OF CONFORMITY

Related manuals

Clarke

JETSTAR 1850

Clarke

JET 9500B

Clarke

POWER WASH JET 7000

Clarke

JET 8500

Clarke

HLS130

Clarke

JETSTAR 1750

Clarke

JETSTAR 1750

Clarke

KING150

Clarke

HLS160

Clarke

JETSTAR 1750

Clarke

TIGER 2600A

Clarke

7320201

Table of contents