Network Technologies VOPEX-USBV-4 Installation and Operation Manual
Network Technologies VOPEX-USBV-4 is a powerful USB KVM Splitter and 3-Port Hub. It allows you to control one USB-enabled CPU through four separate USB keyboards, USB mice, and VGA monitors. The VOPEX-USBV-4 also enables the connection of three additional USB devices, such as printers, scanners, or cameras. Each user can have complete control of the CPU, and each user monitor will show the same image at all times.
Advertisement
Advertisement
VOPEX
®
Series
VOPEX-USBV-2/4
USB Keyboard, Video, and Mouse
Splitter/Hub
Installation and Operation Manual
Front and Rear View of VOPEX-USBV-4
MAN034 Rev Date 12/16/2010
TRADEMARK
VOPEX is a registered trademark of Network Technologies Inc in the U.S. and other countries.
COPYRIGHT
Copyright © 2004, 2010 by Network Technologies Inc. All rights reserved. No part of this publication may be reproduced, stored in a retrieval system, or transmitted, in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, without the prior written consent of Network Technologies Inc, 1275 Danner Drive, Aurora, Ohio 44202.
CHANGES
The material in this guide is for information only and is subject to change without notice. Network Technologies Inc reserves the right to make changes in the product design without reservation and without notification to its users.
i
TABLE OF CONTENTS
INTRODUCTION ............................................................................................................................................................. 1
LIMITATIONS .................................................................................................................................................................. 1
MATERIALS .................................................................................................................................................................... 1
FEATURES AND FUNCTIONS....................................................................................................................................... 2
INSTALLATION ............................................................................................................................................................... 3
Monitor Connection...................................................................................................................................................... 3
Mouse Connection....................................................................................................................................................... 3
Keyboard Connection .................................................................................................................................................. 3
CPU Connection .......................................................................................................................................................... 4
Hub Ports ..................................................................................................................................................................... 4
Power-Up ..................................................................................................................................................................... 4
OPERATION ................................................................................................................................................................... 5
Keyboard Command Mode.......................................................................................................................................... 5
Mice and Trackballs with MACs .................................................................................................................................. 6
International SUN Keyboards ...................................................................................................................................... 6
Hub Ports ..................................................................................................................................................................... 7
AUDIO SUPPORT OPTION............................................................................................................................................ 7
SPECIFICATIONS .......................................................................................................................................................... 7
TROUBLESHOOTING .................................................................................................................................................... 8
WARRANTY INFORMATION.......................................................................................................................................... 8
TABLE OF FIGURES
Figure 1- Connect User 1 Keyboard, Mouse, and Monitor................................................................................................................. 3
Figure 2- Connect the VOPEX to the CPU ........................................................................................................................................ 4
Figure 3- Connect other devices to Hub Ports ................................................................................................................................... 4
ii
NTI VOPEX-USBV-2 KVM SPLITTER
INTRODUCTION
The VOPEX-USBV-2/4 (VOPEX) is a USB KVM Splitter and 3-Port Hub. It enables the control of one USB enabled CPU through two (or four) separate USB keyboards, USB mice, and VGA monitors and it enables the connection of 3 additional USB devices
(other than keyboards or mice). Each user is able to have complete control of a CPU, provided they don't try to access it at the same time. While the user access is controlled by separate modes of operation, each user monitor will show the same image at all times. The 3 hub ports (for printer, scanner, camera, etc.) will be connected to the CPU at all times.
OPTION: Audio support to enable each user to connect stereo speakers to receive audio signals from the connected CPU- add
"-A" to the part number (i.e. VOPEX-USBVA-2/4)
Types of User Input Devices Supported:
•
USB keyboard with Windows layout
•
USB keyboard with SUN layout
•
USB keyboard with MAC layout
•
USB Mouse - (up to 3 buttons)
•
USB IntelliMouse (scroll wheel)
• Mouse-Trak
•
Logitech, Kensington and Microsoft Wheelmouse or Trackball on Mac CPUs with special drivers
•
Logitech Cordless Elite Duo keyboard and mouse
•
Crystal Vision keyboard with touchpad
• Gyration
•
NTI USB-PS/2 Adapter
•
NTI USB-SUN Adapter
Types of Shared Devices Supported:
•
USB 2.0 compliant (low/full speed).
•
Plug-n-Play specification supported
Types of CPUs Supported:
Any USB CPU supporting USB version 1.0 or above including:
WINxx
• USB
SUN
LIMITATIONS
•
The USB ports on the VOPEX are USB 2.0 (low/full speed) compatible. Any USB 2.0 device connected to the VOPEX will be regulated to USB 2.0 low/full speeds.
MATERIALS
Materials included with this kit:
•
VOPEX-USBV-2/4 2/4-Port USB KVM Splitter
•
USB-AB-1M-ST 1 Meter Transparent USB A-B Device Cable
•
VEXT-3 3 Foot M-F VGA Video Cable
•
120 or 240VAC @ 50 or 60Hz-5VDC/2.0A AC Adapter (2-Port models)
-Or –
120 or 240VAC @ 50 or 60Hz-5VDC/6.0A AC Adapter (4-Port models)
•
SA-3-MM 3 Foot M-M 3.5mm Stereo Audio Cable (Models with audio support only)
•
This manual
1
NTI VOPEX-USBV-2 KVM SPLITTER
FEATURES AND FUNCTIONS
1. Power Switch- to power up or power down the VOPEX.
2. Power LED- for visual indication of splitter's power status
3. Mode Status LED’s- for visual indication of splitter's operating mode
4. Mode Switch- press to manually switch between operating modes
5. VIDEO- 15HD male connector- for connecting the video cable from the CPU
6. MONITOR x- 15HD female connectors- for connection of the user video monitors
7. 5VDC- connection jack for the AC adapter
8. DEVICES x- USB type A female connectors- for connection of the cables from USB devices
9. USER x DEVICES- USB type A female connectors- for connection of user USB device(s)
10. CPU- USB type B female connector- for connection of the devices cable from the CPU
2
NTI VOPEX-USBV-2 KVM SPLITTER
INSTALLATION
FYI: It is not necessary to disconnect power to the CPU and monitor(s) before installation.
Monitor Connection
1.
Disconnect the monitor cable at the CPU and reconnect it to the "MONITOR 1" port on the VOPEX. (See Fig. 1)
2.
Plug a second monitor (or optional VEXT-xx extension cable) into the "MONITOR 2" port on the VOPEX.
Note: "xx" in VEXT-xx indicates the length of the cable in feet. Many lengths are available. Contact your VPI salesperson or visit our web site at http://www.vpi.us for details.
Note: The monitor connected to “MONITOR 1” will send DDC data to the connected CPU. Be sure to connect a monitor to “MONITOR1” to ensure the CPU has the required video configuration information to work properly.
Mouse Connection
1.
Disconnect the mouse at the CPU and reconnect it to one of the female USB type A 'USER 1 DEVICES" ports on the
VOPEX.
2.
Connect a second mouse (or optional USB extension cable NTI USB2-AA-5M) to the female USB type A "USER 2 DEVICES" ports on the VOPEX.
Keyboard Connection
1. Disconnect the keyboard at the CPU and reconnect the keyboard to the remaining female USB type A "USER 1 DEVICES" port on the VOPEX.
2. Connect a second keyboard (or optional USB extension cable NTI USB2-AA-5M) to the remaining female USB type A "USER
2 DEVICES" ports on the VOPEX.
Figure 1- Connect User 1 Keyboard, Mouse, and Monitor
3
NTI VOPEX-USBV-2 KVM SPLITTER
CPU Connection
1.
Connect the male USB type A connector end of the USB-AB-1M-ST cable into the device port on the CPU.
2.
Connect the male USB type B connector of the same cable to the "CPU" port on the VOPEX.
3.
4.
Connect the male 15HD connector end of the VEXT-3 into the CPU’s video port. (See Fig. 2)
Connect the female 15HD connector end of the VEXT-3 into the "VIDEO" port on the VOPEX.
Figure 2- Connect the VOPEX to the CPU
Hub Ports
If desired, connect additional USB devices to each of the three "Hub Ports". These ports will be powered and operational anytime the VOPEX and CPU are powered ON. See Fig. 3.
Power-Up
If not already ON, turn ON power to the CPU, monitors, and VOPEX.
Figure 3- Connect other devices to Hub Ports
4
NTI VOPEX-USBV-2 KVM SPLITTER
OPERATION
Mode Selection
The VOPEX comes equipped with four (VOPEX-USBV-2) or six (VOPEX-USBV-4) modes of operation. To manually toggle between modes, depress the MODE button once each time a mode change is desired. The VOPEX will cycle through the modes of operation, then return to the first mode (1 to 2, 2 to 3, 3 to 4, etc). The following table details the modes of operation.
MODE
1- INSTANTANEOUS
2- DELAY
DESCRIPTION
Both users have control of the CPU simultaneously.
The first user with an active device gets control of
CPU. The second user is locked out until after 5 seconds of inactivity from the first user.
INDICATOR LEDS
3- USER 1 "USER 1" has sole access. Other users are locked out.
4- USER 2 "USER 2" has sole access. Other users are locked out.
5- USER 3
6- USER 4
"USER 3" has sole access. Other users are locked out.
"USER 4" has sole access. Other users are locked out.
Keyboard Command Mode
In order to control the other features of the VOPEX with the keyboard, Command Mode must be enabled. To enter
Command Mode from the keyboard:
Press
Ctrl
+
`
~
(ACCENT
KEY)
When the Command Mode is enabled, all 3 status lights on the keyboard will illuminate and both LED’s on the VOPEX will blink continuously to indicate Command Mode is enabled. See the table below for functions that are available while in Command
Mode.
NOTE: The user must exit Command Mode in order for the CPU to switch to the selected mode. To exit Command Mode, press ESC on the keyboard. The mouse will not operate while in Command Mode.
NOTE: While in Command Mode, when a proper programming command is entered and is recognized by the switch, the
LED’s on the keyboard will flash once to indicate acceptance. The user must exit Command Mode (by pressing ESC) to
see a change take effect in the switch operation.
NOTE: The VOPEX will automatically exit Command Mode after 5 seconds of inactivity by the user if the user does not manually exit Command Mode.
5
NTI VOPEX-USBV-2 KVM SPLITTER
The following functions exist while in Command Mode:
Key Combination
<X>-<key>-<Y>
Description of Function
Select a new key sequence to use to enter Command Mode – Replace <key> with the desired key to follow <Ctrl> with.
<L> - <x> - <x>
<V> - <Enter>
<M>
<W>
<D> - <x>
<P> - <x>
<Esc>
Select the country code of the keyboard being used with a USB SUN CPU (see Country Codes chart on page 6)
This will print the version of the code in the VOPEX to a text editor window (i.e. Windows Notepad) for use when troubleshooting the VOPEX. Note: The text editor should be open prior to entering
Command Mode.
Configure the CPU port to connect to a MAC CPU (see "Mice and Trackballs with MACs" on pg. 6.
Configure the CPU port to connect to a Windows or SUN CPU
Select the operating mode, x=1 for Instantaneous Mode, x=2 for Delay Mode, x=3 User 1 Mode, x=4 for User 2 mode, x=5 for User 3 mode, x=6 for User 4 mode. (Modes are described in the table on page 5.)
Select the default mode to have the VOPEX enter upon power-up.
Exit Command Mode
Mice and Trackballs with MACs
The VOPEX can be configured to enable full functionality between mice and trackballs having two or more buttons and a USB
MAC CPU. By default, the CPU port on the VOPEX is configured for use with a WINDOWS or SUN CPU and has no special translation for using multi-function mice and trackballs when a MAC CPU is connected. Using the commands in Command Mode above, either enable or disable this feature as needed.
NOTE: Be sure to re-configure the port for connection to a WINDOWS or SUN CPU if a MAC CPU is removed and a
WINDOWS or SUN CPU is then connected.
International SUN Keyboards
The VOPEX can recognize international layouts for Sun keyboards. To use an international Sun keyboard, follow this procedure:
1. Disconnect the CPU from the VOPEX
2. Connect the international keyboard to be used to the VOPEX
3. Power down the VOPEX for at least 3 seconds
4. Power up the VOPEX
5. Reconnect the CPU to the VOPEX
It is also possible to configure the VOPEX to emulate a specific international Sun keyboard regardless of what actual keyboard is connected. This is recommended when the CPU needs the layout code (i.e. a SUN CPU) and the keyboard doesn't have an explicit layout code (i.e. some Windows keyboards). To do this, manually set the VOPEX to indicate the international keyboard identification number to the CPU using the following procedure:
1. Connect the keyboard to be used to the VOPEX
2. Power down the VOPEX for at least 3 seconds
3. Power up the VOPEX
4. Enter Command Mode (<Ctrl> - <`>)
5. Type Lxx, where xx is the number from the list below that corresponds to the desired country code
6. Exit Command Mode
7. Power down the VOPEX for at least 3 seconds
8. Power up the VOPEX
9. Reboot the CPU connected to the VOPEX
Country Codes
00 Not 10 Greek
01 Arabic
02 Belgian
11 Hebrew
12 Hungary
31 Turkish
32 UK
33 US
04 Canadian-French 14 Italian
06 Danish
07 Finnish
08 French
09 German
16 Korean
American 27
19 Norwegian
28
6
NTI VOPEX-USBV-2 KVM SPLITTER
Hub Ports
The three connections labeled "Hub Ports" can be used to connect any USB device, such as a printer, scanner, camera, etc. for continuous operation at USB 2.0 compliant (low or full) speeds. These ports are not controlled by the VOPEX.
AUDIO SUPPORT OPTION
If your VOPEX has the audio support option built-in (VOPEX-USBVA-2/4), there are 3.5mm stereo audio jacks for the connection of the audio from the CPU and to self-powered stereo speakers for each user. Each user will receive audio signals at all times.
Audio support provides the following additional features:
•
Audio signals from the same CPU that keyboard, mouse, and video signals are from can be received by each user.
•
Audio inputs accept any standard line level audio (4Vp-p).
•
Audio outputs are capable of driving self-powered speakers or headphones.
A SA-3-MM 3-foot 3.5mm stereo audio cable has been provided to connect the audio from the CPU to the VOPEX (Additional
3,6,10,15,25,35,50 and 100 foot lengths are available from NTI).
User audio ports
Audio In port for connection from CPU
SPECIFICATIONS
Size: Each unit is 8.5”W x 6”D x 2.6”H
Power: Powered by 120 or 240VAC @ 50 or 60Hz-5VDC/2.0A AC Adapter (2-Port VOPEX) or 6.0A AC Adapter (4-Port VOPEX)
Connections: 15HD VGA & SGA compatible
USB Type A female device connectors
USB Type B female CPU connector
7
NTI VOPEX-USBV-2 KVM SPLITTER
TROUBLESHOOTING
PROBLEM SOLUTION
• Keyboard
• Mouse
•
•
Check cable connections on CPU and VOPEX
Check cable connections on CPU and VOPEX
•
Make sure a monitor is connected to “MONITOR 1”
•
Check cable connections on CPU and VOPEX
WARRANTY INFORMATION
The warranty period on this product (parts and labor) is two (2) years from the date of purchase. Please contact Network
Technologies Inc at (800) 742-8324 (800-RGB-TECH) or (330) 562-7070 or visit our website at http://www.networktechinc.com
for information regarding repairs and/or returns. A return authorization number is required for all repairs/returns.
MODEL NO: VOPEX-USBV-__
SERIAL NO: _____________________
DATE: _____________________
INSPECTED BY: ________________
Man034 Rev 12/16/10
8

Public link updated
The public link to your chat has been updated.
Advertisement
Key features
- Control one CPU with four separate keyboards, mice, and monitors
- Connect three additional USB devices (printers, scanners, cameras, etc.)
- Supports USB 2.0 compliant devices (low/full speed)
- Plug-and-play specification supported
- Compatible with any USB CPU supporting USB version 1.0 or above (WINxx, MAC, SUN)
- Manual mode switching for easy control
- LED indicators for visual indication of splitter status