E2S AB112RTH sounder User manual
Below you will find brief information for sounder AB112RTH. This document outlines the specifications of the AB112RTH sounder, including its features such as the 45 selectable alarm tones, the rotating beacon, and the IP65 rating. It also provides guidance on installation and wiring, as well as important safety precautions. This document is a useful guide for anyone who needs to understand how the AB112RTH sounder operates and use it effectively.
advertisement
▼
Scroll to page 2
1 Nominal voltage & range AB112RTH Bulb replacement E2S Part No. BJC20W12VCL BJC20W24VCL BJCD25W120VCL BJCD25W230VCL Version 12V 20W 24V 20W 115V 25W 230V 25W Example:- AB112RTHDC24G/R This example is for a A112N sounder with rotating beacon running on 24VDC the housing is grey with a red lens. AB112RTHAC230y/x 230VAC (207-253VAC) Beacon 117mA Sounder 60mA @ 230VAC AB112RTHAC115y/x 115VAC (103-127VAC) Beacon 216mA Sounder 100mA @ 115VAC AB112RTHDC24y/x 24VDC (18-30VDC) Beacon 910mA Sounder 200mA @24VDC AB112RTHDC12y/x 12VDC (10-15VDC) Beacon 1720mA Sounder 400mA @12VDC Order code SpectrAlarm Sounder unit A112N Maximum output: 119 dB(A) @ 1 m Nominal output: 112 dB(A) @ 1 m - tone 2 45 Alarm tones (UKO OA/PREER Compliant) Rotating Beacon G6,35/GY6,35 Halogen Bulb IP Rating: IP65 Temp: -25°C to +50°C Unit weight: 2.2kg DC 2.5kg AC CE Dimensions : 168mm(w) x 318mm(h) 1.5mm² terminals For Lens colour options x = in order code to be replaced with required lens colour R = Red A = Amber B = Blue C = Clear G = Green Y = Yellow y = in order code to be replaced with required housing colour G = Grey R = Red ATTENTION: Installation must be carried out by an electrician in compliance with the latest codes and regulations. ATTENTION: Disconnect from power source before installation or service to prevent electric shock. warning signals ATTENTION: On strobe beacons allow a minimum of 2 minutes for hazardous high voltage to discharge from unit. ATTENTION: Lens on unit will be hot allow to cool prior to removal. Tel : +44(0)20 8743 8880 Fax : +44(0)20 8740 4200 mail : [email protected] web : www.e2s.com 2 AB112RTH Sounder Tone Settings Table For switch settings please note:Where 1 is indicated the switch position is on. Where 0 is indicated the switch position is off. ON 3 4 5 6 APEMs Example:Table shows 1 0 0 0 0 0 Switch setting On Off Off Off Off Off 1 2 Tone 2 Tone 2 Tone 17 Stage 2 Tone 2 Tone 5 Tone 20 Tone 5 Tone 5 Tone 5 Tone 5 Tone 5 Tone 5 Stage 3 Frequency Description Tone 6 Tone 3 Tone 7 Tone 10 Tone 2 Stage 1 0 1 0 0 0 0 Switch 1 2 3 4 5 6 0 0 0 0 0 0 1 0 0 0 0 0 Tone 15 Tone 5 Tone 5 Tone 5 Tone 5 Tone 5 Tone 5 Tone 5 800/1000Hz @ 1Hz Sweeping 2400Hz Continuous 2400/2900Hz @ 7Hz Sweeping 2400/2900Hz @ 1Hz Sweeping 500/1200/500Hz @ 0.3Hz Sweeping 1200/500Hz @ 1Hz - DIN PFEER P.T.A.P. 2400/2900Hz @ 2Hz Alternating 1000Hz @ 1Hz Intermittent 800/1000Hz @ 0.875Hz Alternating 2400Hz @ 1Hz Intermittent 800Hz 0.25 sec on, 1 sec off Intermittent 0 0 0 1 1 1 1 1 1 1 1 1 1 1 0 0 0 0 0 0 0 Tone 5 0 1 1 0 0 1 1 Tone 5 Tone 5 Tone 5 Tone 5 Tone 5 Tone 5 Tone 15 Tone 5 Tone 5 Tone 5 Tone 5 Tone 5 Tone 15 Tone 5 800Hz Continuous 660Hz 150mS on, 150mS off Intermittent Tone 2 Tone 2 Tone 2 Tone 6 Tone 29 Tone 29 Tone 2 Tone 26 Tone 2 Tone 7 Tone 2 Tone 26 Tone 26 Tone 2 Tone 5 Tone 45 10 11 12 13 14 15 16 9 4 5 6 7 8 340Hz Continuous 800/1000Hz @ 0.25 sec Alternating Tone 7 Tone 2 Tone 4 Tone 15 Tone 4 Tone 2 Tone 18 Tone 5 Tone 27 1 2 0 0 0 1 0 0 1 0 1 0 1 0 0 0 0 0 0 0 Tone 2 500/1200Hz @ 0.3Hz sec Slow Whoop 1 0 1 0 1 0 1 Tone 2 3 0 0 0 0 1 0 Tone 2 0 0 0 0 0 0 0 0 0 0 0 0 0 1 Tone 38 0 0 0 0 0 544Hz (100mS)/440 Hz (400m/S) - NF S 32-001 0 1 0 0 1 0 1 0 0 0 1 0 0 0 0 0 0 660Hz 1.8 sec on, 1.8 sec off Intermittent 0 0 0 0 0 17 1.4KHz - 1.6KHz 1s, 1.6KHz - 1.4 KHz 0.5s - NFC48-265 0 1 1 1 1 18 1 0 0 1 1 19 1 0 1 0 1 0 1 0 1 0 1 0 1 0 Tone 36 Tone 27 Tone 45 Tone 45 Tone 17 Tone 5 Two tone chime 745Hz @ 1Hz Intermittent 300Hz Continuous 660/1200Hz @ 1Hz Sweeping Bell 554Hz Continuous 440Hz Continuous 800/1000Hz @ 7Hz Sweeping 660Hz Continuous 554Hz/440Hz @ 1Hz Alternating 544Hz @ 0.875 sec Intermittent 800Hz @ 2Hz Intermittent 800/1000Hz @ 50Hz Sweeping 2400/2900Hz @ 50Hz Sweeping 1 0 0 0 0 1 Tone 35 Tone 31 Tone 9 Tone 34 Tone 23 1 1 1 1 1 1 1 1 1 1 1 1 1 0 0 1 0 0 0 1 0 0 1 0 0 1 1 0 1 0 0 1 0 1 1 0 0 1 0 0 0 0 0 1 1 1 1 1 1 1 1 0 1000 & 2000Hz @ 0.5 sec Aletrnating - Signapore 1 1 0 0 0 1 1 1 1 0 0 1 0 1 1 1 1 0 0 0 0 1 1 1 1 0 420Hz @ 0.625 Sec Australian Alert 1000Hz Continuous - PFEER Toxic Gas 2000Hz Continuous 800Hz 0.25 sec on, 1 sec off Intermittent Tone 5 Tone 5 Tone 5 Tone 5 1 0 0 1 1 0 0 1 1 0 0 1 1 0 34 500-1200Hz 3.75 sec /0.25 sec Australian Evac. 37 38 39 544Hz (100mS)/440Hz (400mS) - NF S 32-001 Tone 34 20 21 22 23 24 25 26 27 28 29 30 31 32 33 36 35 40 Tone 2 Tone 2 Tone 2 Tone 2 1 1 1 1 Tone 38 0 0 0 0 0 0 1 1 0 1 0 1 0 1 1 1 1 1 Motor Siren - slow rise to 1200Hz Motor Siren - slow rise to 800Hz 1200Hz Continuous Motor Siren - slow rise to 2400Hz 0 0 0 0 41 42 43 44 1KHz 1s on, 1s off Intermittent - PFEER Gen. Alarm 0 0 1 1 45 warning signals D118-00-601-IS_SHT1_ISSUE_A Beacon DC CIRCUIT WIRING DIAGRAM ON 1 2 APEMs 3 4 5 6 S2 TONE SELECTION SWITCH SHOWN DEFAULT TONE 2 (100000) SEE SOUNDER TONE SETTINGS TABLE S2 S3 - 3 4 N Beacon L E E N N L L TERMINAL ON MASTER PCB CUSTOMER SUPPLIED SWITCHES AS REQUIRED FOR STAGE 2 (S2) AND STAGE 3 (S3 ) S3 MIN VOLUME CONTROL SHOWN SET TO MAX MAX Sounder + APEMs 3 4 5 6 S2 S3 - - + + TERMINAL ON MASTER PCB 1 2 S3 ON B S2 - CUSTOMER SUPPLIED SWITCHES AS REQUIRED FOR STAGE 2 (S2) AND STAGE 3 (S3) AC CIRCUIT WIRING DIAGRAM warning signals warning signals D118-00-601-IS_SHT2_ISSUE_A 5 Sounder C 2 APEMs 145 168 1 FOR LENS REPLACEMENT REVERSE PROCEDURE 3 4 5 6 168 190 warning signals 1 2 190 Ø9.0 HOLES 2 POS'NS IP65 Gland Not Supplied Tel : +44(0)20 8743 8880 Fax : +44(0)2 8740 4200 mail : [email protected] web : www.e2s.com ON A 156.5mm SpectrAlarm AB112RTH 2x Fixings Customer Supplied Dimensions in mm
advertisement
Key Features
- 45 selectable alarm tones
- Rotating beacon
- IP65 rating
- 119 dB(A) maximum output
- 112 dB(A) nominal output
- Tone 2
- Stage 2 & 3
- Volume control
- 1.5mm² terminals
- 12V, 24V, 115V and 230V versions
Frequently Answers and Questions
What are the different voltage and current ratings for the AB112RTH sounder?
The AB112RTH sounder is available in 12V, 24V, 115V and 230V versions. Its current draw varies depending on the voltage. Refer to the document for specific current ratings at each voltage level.
How do I select the desired tone for the AB112RTH sounder?
You can select from 45 different alarm tones using the tone selection switches on the sounder unit. Refer to the document for the detailed tone settings table and instructions on how to configure the switches for your desired tone.
How do I replace the bulb on the AB112RTH sounder?
To replace the bulb, refer to the document for the detailed procedure. It includes step-by-step instructions on how to access the bulb and safely replace it. Remember to let the unit cool before removing the lens.
What are the dimensions of the AB112RTH sounder?
The AB112RTH sounder's dimensions are 168mm (w) x 318mm (h). See the document for a visual representation of the dimensions.
What is the IP rating of the AB112RTH sounder?
The AB112RTH sounder has an IP65 rating, which means it is protected against dust ingress and water jets from any direction.
What are the operating temperature ranges for the AB112RTH sounder?
The AB112RTH sounder can operate in temperatures ranging from -25°C to +50°C.
Related manuals
Download
PDF
advertisement
