Barco | R9002249 | Installation manual | Barco R9002249 Installation manual

Barco R9002249 Installation manual
VISION
1609s
R9002240
R9002249
INSTALLATION MANUAL
BARCO PROJECTION SYSTEMS
VISION
1609s
R9002240
R9002249
INSTALLATION MANUAL
Date :
220198
rev 01
Art. No. :
R5975698
Due to constant research, the information in this manual is subject to change without notice.
Produced by BARCO NV, January 1998.
All rights reserved.
Trademarks are the rights of their respective owners.
BARCO nv/Projection Systems
Noordlaan 5
B-8520 Kuurne
Belgium
Tel : +32/56/368211
Fax : +32/56/351651
E-mail : sales.bps@barco.com
Visite Barco at the web : http://www.barco.com
Printed in Belgium
Table of contents
TABLE OF CONTENTS ................................................................................................................................ I-1
SAFETY INSTRUCTIONS
On safety .............................................................................................................................................
On installation ......................................................................................................................................
On servicing .........................................................................................................................................
On cleaning ..........................................................................................................................................
On repacking .......................................................................................................................................
On illumination .....................................................................................................................................
1-1
1-2
1-2
1-2
1-2
1-2
UNPACKING AND PROJECTOR DIMENSIONS
Unpacking ............................................................................................................................................ 2-1
Projector dimensions ........................................................................................................................... 2-2
INSTALLATION GUIDELINES
Environment .........................................................................................................................................
What about ambient light ? ..................................................................................................................
Which screen type? .............................................................................................................................
What image size? How big should the image be? ..............................................................................
Where to install the projector ? ............................................................................................................
Mounting Configuration ........................................................................................................................
3-1
3-1
3-1
3-1
3-2
3-2
INSTALLATION SET-UP
Access to Controls .............................................................................................................................. 4-1
Opening the top cover ................................................................................................................................................................. 4-1
Removing the top cover .............................................................................................................................................................. 4-1
Re-installing the top cover .......................................................................................................................................................... 4-1
Scan Adaptation .................................................................................................................................. 4-2
Getting access to the scan switches ........................................................................................................................................ 4-2
Horizontal scan switches ........................................................................................................................................................... 4-3
Vertical scan switch ................................................................................................................................................................... 4-3
PROJECTOR SET-UP
Setting the projector address ............................................................................................................... 5-2
Power-up mode .................................................................................................................................... 5-3
Operational mode ........................................................................................................................................................................ 5-3
Stand-By mode ............................................................................................................................................................................ 5-3
Baud Rate for communication with a computer .................................................................................... 5-3
Password mode ................................................................................................................................... 5-4
AC POWER CONNECTION
AC Power cord connection .................................................................................................................. 6-1
Preparing your power cord ................................................................................................................... 6-1
Mains lead with CEE7 plug .......................................................................................................................................................... 6-1
Power cord with an ANSI 73.11 plug ......................................................................................................................................... 6-1
AC Power check ..................................................................................................................................
AC Input power voltage adaptation .......................................................................................................
Switching on the projector ...................................................................................................................
Starting up with a full white image .......................................................................................................
6-2
6-2
6-3
6-3
SOURCE CONNECTIONS
Signal input connection........................................................................................................................
Connecting a Composite Video source to Port 1 .................................................................................
Connecting a S-Video (or Composite Video) source to Port 2 .............................................................
Connecting a RGB Analog source to Port 3 ........................................................................................
Connecting a RGB Analog source to Port 4/5 .....................................................................................
7-1
7-1
7-2
7-2
7-3
Starting up with "warm up period" .............................................................................................................................................. 6-3
Starting up without "warm up period" ........................................................................................................................................ 6-3
5975698 BARCOGRAPHICS 1609s 220198
i-1
Table of contents
Connecting a Component Video source to Port 4/5 ............................................................................. 7-3
Connecting a RGB Analog source with Tri-level sync to Port 4/5 (option) ............................................ 7-4
Connecting a Component Video source with Tri-level sync to Port 4/5 (option) ................................... 7-4
Peripheral equipment ........................................................................................................................... 7-4
Connecting a RCVDS 05 source selector to the projector ........................................................................................................ 7-4
Connecting a VS05 source selector to the projector ................................................................................................................. 7-4
Connecting an IR Remote Receiver 800 to the projector ........................................................................................................... 7-4
INSTALLATION ADJUSTMENT MODE
Access to Installation Adjustment Mode .............................................................................................
Overview flowchart of the Installation Adjustment Mode .......................................................................
Projector Distance ...............................................................................................................................
Optical Lens Focusing .........................................................................................................................
Raster Centering ..................................................................................................................................
CRT Projection Angle Adjustment .......................................................................................................
Scheimpfug Adjustment .......................................................................................................................
8-1
8-1
8-2
8-2
8-3
8-4
8-6
Appendix A : Barco ceiling mount support
Appendix B : G2 adjustment
Appendix C : Gamma corrections
i-2
5975698 BARCOGRAPHICS 1609s 220198
Safety Instructions
1
SAFETY INSTRUCTIONS
Notice on Safety
This equipment is built in accordance with the requirements of the
international safety standards EN60950, UL 1950 and CSA C22.2
No.950, which are the safety standards of information technology
equipment including electrical business equipment.
These safety standards impose important requirements on the use of
safety critical components, materials and isolation, in order to protect
the user or operator against risk of electric shock and energy hazard,
and having access to live parts.
Safety standards also impose limits to the internal and external
temperature rises, radiation levels, mechanical stability and strength,
enclosure construction and protection against the risk of fire.
Simulated single fault condition testing ensures the safety of the
equipment to the user even when the equipment's normal operation
fails.
INSTALLATION INSTRUCTIONS
Before operating this equipment please read this manual
thoroughly, and retain it for future reference.
Installation and preliminary adjustments should be performed
by qualified BARCO personnel or by authorized BARCO
service dealers.
OWNER’S RECORD
The part number and serial number are located at the back side of the
projector. Record these numbers in the spaces provided below. Refer
to them whenever you call upon your BARCO dealer regarding this
product.
PART NUMBER :
WARNING
TO PREVENT FIRE OR ELECTRICAL SHOCK
HAZARD, DO NOT EXPOSE THIS EQUIPMENT TO
RAIN OR MOISTURE
FEDERAL COMMUNICATION COMMISSION (FCC STATEMENT)
This equipment has been tested and found to comply with the limits
of a class B digital device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against
harmful interference when the equipment is operated in a commercial
environment. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the
instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely
to cause harmful interference in which case the user will be required
to correct the interference at his own expense.
Instructions to the user :
If this equipment does cause interference to radio or television
reception, the user may try to correct the interference by one or more
of the following measures :
- Re-orientation of the receiving antenna for the radio or television.
- Relocate the equipment with respect to the receiver.
- Plug the equipment into a different outlet so that the equipment and
receiver are on different branch circuits.
- Fasten cables connectors to the equipment by mounting screws.
Note :
The use of shielded cables is required to comply within the limits of
Part 15 of FCC rules and EN55022.
* All the safety and operating instructions should be read before using
this unit.
* The safety and operating instructions manual should be retained for
future reference.
SER. NUMBER :
* All warnings on the equipment and in the documentation manuals
should be adhered to.
DEALER :
* All instructions for operating and use of this equipment must be
followed precisely.
On safety
1. This product should be operated from an AC power source.
This projector may be connected to an IT-power system.
Operating AC power voltage of the projector:
The lightning flash with an arrowhead within a
triangle is intended to tell the user that parts
inside this product may cause a risk of electrical
shock to persons.
The exclamation point within a triangle is intended to tell the user that important operating
and/or servicing instructions are included in the
technical documentation for this equipment.
5975698 BARCOVISION 1609S 220198
BARCOVISION 1609s
Art.No. R9002240 (230V AC)
Art. No R9002249 (120V AC)
Consult your dealer to switch over from 230Vac to 120 Vac or from
120Vac to 230 Vac.
If you are not sure of the type of AC power available, consult your
dealer or local power company.
2. This product is equipped with a 3-wire grounding plug, a plug
having a third (grounding) pin. This plug will only fit into a groundingtype power outlet. This is a safety feature. If you are unable to insert
the plug into the outlet, contact your electrician to replace your
obsolete outlet. Do not defeat the purpose of the grounding-type plug.
1-1
Safety Instructions
WARNING FOR THE CUSTOMERS: THIS APPARATUS MUST BE
GROUNDED (EARTHED) via the supplied 3 conductor AC power
cable. (If the supplied power cable is not the correct one, consult your
dealer.)
Refer all servicing to qualified service personnel.
Unplug this product from the wall outlet and refer servicing to
qualified service personnel under the following conditions:
A. Mains lead (Power cord) with CEE 7 plug:
The wires of the mains lead are colored in
accordance with the following code.
Green and yellow: earth (safety earth)
Blue:
neutral
Brown:
line (live)
B. Power cord with ANSI 73.11 plug:
The wires of the power cord are colored in
accordance with the following code.
Green/yellow: ground
White:
neutral
Black:
line (live)
3. Do not allow anything to rest on the power
cord. Do not locate this product where persons will walk on the cord.
To disconnect the cord, pull it out by the plug. Never pull the cord itself.
4. If an extension cord is used with this product, make sure that the
total of the ampere ratings on the products plugged into the extension
cord does not exceed the extension cord ampere rating. Also make
sure that the total of all products plugged into the wall outlet does not
exceed 15 amperes.
5. Never push objects of any kind into this product through cabinet
slots as they may touch dangerous voltage points or short out parts
that could result in a risk of fire or electrical shock.
A. When the power cord or plug is damaged or frayed.
B. If liquid has been spilled into the equipment.
C. If the product has been exposed to rain or water.
D. If the product does not operate normally when the operating
instructions are followed.
Note : Adjust only those controls that are covered by the operating
instructions since improper adjustment of the other controls may
result in damage and will often require extensive work by a qualified
technician to restore the product to normal operation.
E. If the product has been dropped or the cabinet has been damaged.
F. If the product exhibits a distinct change in performance, indicating
a need for service.
Replacement parts - When replacement parts are required, be sure
the service technician has used original BARCO replacement parts
or authorized replacement parts which have the same characteristics
as the BARCO original part. Unauthorized substitutions may result in
degraded performance and reliability, fire, electric shock or other
hazards. Unauthorized substitutions may void warranty.
Safety check - Upon completion of any service or repairs to this
projector, ask the service technician to perform safety checks to
determine that the product is in proper
operating condition.
On cleaning
Unplug this product from the wall outlet before cleaning. Do not
use liquid cleaners or aerosol cleaners. Use a damp cloth for
cleaning.
6. Lightning - For added protection for this video product during a
lightning storm, or when it is left unattended and unused for long
periods of time, unplug it from the wall outlet. This will prevent damage
to the projector due to lightning and AC power-line surges.
- To keep the cabinet looking brand-new, periodically clean it with a
soft cloth. Stubborn stains may be removed with a cloth lightly
dampened with mild detergent solution. Never use strong solvents,
such as thinner or benzine, or abrasive cleaners, since these will
damage the cabinet.
- To ensure the highest optical performance and resolution, the
projection lenses are specially treated with an anti-reflective coating, therefore, avoid touching the lens. To remove dust on the lens,
use a soft dry cloth. Do not use a damp cloth, detergent solution, or
thinner.
On installation
On repacking
1. Do not place this equipment on an unstable cart, stand, or table.
The product may fall, causing serious damage to it.
Save the original shipping carton and packing material; they will come
in handy if you ever have to ship your equipment. For maximum
protection, repack your set as it was originally packed at the factory.
Never spill liquid of any kind on the product. Should any liquid or solid
object fall into the cabinet, unplug the set and have it checked by
qualified service personnel before resuming operations.
2. Do not use this equipment near water.
On illumination
3. Slots and openings in the cabinet and the back or bottom are
provided for ventilation; to ensure reliable operation of the product
and to protect it from overheating, these openings must not be
blocked or covered. The openings should never be blocked by
placing the product on a bed, sofa, rug, or other similar surface. This
product should never be placed near or over a radiator or heat
register.
The projector should not be placed in a built-in installation or enclosure unless proper ventilation is provided.
4. Do not block the projector cooling fans or free air movement under
and around the projector. Loose papers or other objects may not be
nearer to the projector than 4" on any side.
On servicing
Do not attempt to service this product yourself, as opening or
removing covers may expose you to dangerous voltage potentials
and risk of electric shock!
1-2
In order to obtain the best quality for the projected image, it is
essential that the ambient light which is allowed to fall on the screen
be kept to an absolute minimum.
When installing the projector and screen, care must be taken to avoid
exposure to ambient light directly on the screen. Avoid adverse
illumination on the screen from direct sunlight or fluorescent lighting
fixtures.
The use of controlled ambient lighting, such as incandescent spot
light or a dimmer, is recommended for proper room illumination.
Where possible, care should also be taken to ensure that the floors
and walls of the room in which the projector is to be installed are nonreflecting, dark surfaces. Brighter surfaces will tend to reflect and
diffuse the ambient light and hence reduce the contrast of the
projected image on the screen.
5975698 BARCOVISION 1609S 220198
Unpacking and dimensions
2
UNPACKING AND PROJECTOR DIMENSIONS
Unpacking
To open the banding around the carton, pull out the clip as shown
below :
Take the projector out of its shipping carton and place it on a table.
Save the original shipping carton and packing material, which will
come in handy if you ever have to ship your projector. For maximum
protection, repack your projector as it was originally packed at the
factory.
Contents of the shipping carton :
1 BARCOVISION 1609s projector
1 Remote Control Unit plus 1 battery 9V
1 power cord with outlet plug type CEE7 or ANSI 73.11
1 Owner's Manual
1 Installation Manual
1 Adjustment Manual IRIS²
5975698 BARCOVISION 1609s 220198
2-1
Unpacking and dimensions
Projector dimensions (in mm)
W1
H5
L5
L6
L4
L3
L2
L1
H4
H3
H2
W2
H1
2-2
Dimensions
mm
inch
L1
L2
L3
L4
L5
L6
W1
W2
H1
H2
H3
H4
H5
1174
1014
1000
735
110
265
782
665
355
315
219
101
121
46.2
39.9
39.37
28.9
4.33
10.43
30.8
26.2
13.9
12.4
8.62
3.98
4.76
5975698 BARCOVISION 1609s 220198
Installation guidelines
3
INSTALLATION GUIDELINES
Installation Guidelines
Careful consideration of things such as image size, ambient light level, projector placement and type of screen to use are
critical to optimize the use of the projection system.
Environment
Do not install the projection system in a site near heat sources such
as radiators or air ducts, or in a place subject to direct sunlight,
excessive dust or humidity. Be aware that room heat rises to the
ceiling; Make sure the temperature near the installation site is not
excessive.
What about ambient light ?
The ambient light level of any room is made up of direct or indirect
sunlight and the light fixtures in the room. The amount of ambient light
will determine how bright the image will appear. So, avoid direct light
on the screen as much as possible.
Windows that face the screen should be covered by opaque drapery
while the set is being viewed. It is desirable to install the projection
system in a room whose walls and floor are of non-reflecting material.
The use of recessed ceiling lights and a method of dimming those
lights to an acceptable level is also important. Too much ambient light
results in a ‘washed out’ of the projected image. This appears as less
contrast between the darkest and lightest parts of the image. With
bigger screens, the ‘wash out’ becomes more important. As a general
rule, darken the room to the point where there is just sufficient light
to read or write comfortably. Spot lighting is desirable for illuminating
small areas so that interference with the screen is minimal.
Which screen type?
There are two major categories of screens used for projection
equipment. Those used for front projected images and those for rear
projection applications.
Screens are rated by how much light they reflect (or transmit in case
of rear projection systems) given a determined amount of light
projected toward them. The ‘GAIN’ of a screen is the term used. Front
and rear screens are both rated in terms of gain. The gain of screens
range from a white matte screen with a gain of 1 (x1) to a brushed
aluminized screen with a gain of 10 (x10) or more. Another important
consideration is the degree the screen's gain varies with the
horizontal and vertical viewing angle. The choice between higher and
lower gain screens is largely a matter of personal preference.
6FUHHQZLGWK
In considering the type of screen to choose, determine where the
viewers will be located and go for the highest gain screen possible.
A high gain screen will provide a brighter picture but reduce the
viewing angle.
For more information about screens, contact your local
screen supplier.
What image size? How big should the image
be
The projector is designed for projecting an image width from 2m (6.6')
to 3m (10') with HD120 lenses and with an aspect ratio of 4 to 3. It
leaves the BARCO factory, adjusted as a ceiling/front projector for
a screen width of 2.4m (7.8'). Changing the image size from the
factory preset size requires a realignment of the projector.
5975698 BARCOVISION 1609s 220198
3-1
Installation guidelines
Where to install the projector ?
To indicate a correct installation position it is necessary to know :
FHLOLQJ
3'
%
&'
$
The distance from projector to ceiling in case of Ceiling
mounted or the distance from projector to floor in case of Table
mounted;
SURMHFWRU
The distance from projector to screen.
VFUHHQ
To find the correct position for the projector, equipped with HD120
lenses, use the following formulas:
Optinal lenses : HD180 for SW between 3m and 4.2m and HD300
In metric :
)URQWYLHZ
PD[m] = 1.311 x SW[m] + 0.33
A[cm] = 11.3 x SW[m] - 28.188
In inch :
VFUHHQZLGWK
PD[inch] = 1.311 x SW[inch] + 13.029
6:
A[inch] = 0.113 x SW[inch] - 11.098
for SW between 2m and 8.8m
Abbreviations used in the calculations and the drawings :
B = Distance between ceiling and top of the screen (Ceiling
mounted) or distance between floor and bottom of the screen
(Table mounted).
A
7RSYLHZ
*
*
Install the projector water levelled in both directions
Install the projector perpendicular to the screen
= Correction Value, extra value to be added to B to obtain the
correct installation position (In some cases the A value can be
negative).
CD = Total distance between projector and ceiling (Ceiling mounted)
or total distance between projector and floor (Table mounted).
CD = A + B.
14.5 cm
(4.5 inch)
Ceiling Mounted : when the result is negative, enlarge the
distance between ceiling and top of the screen, mount screen
lower, until CD becomes zero or positive.
Table Mounted : when the result is negative, enlarge the
distance between floor and bottom of the screen, mount
screen higher, until CD becomes zero or positive.
SW = Screen width.
green phosphor
PD = Perpendicular distance between screen and projector's mount.
To obtain the right values, you can make use of the new option
included in the Installation Adjustment Mode to let the projector
calculate the parameters automatically. Please refer to Chapter 8 for
details.
Used phosphor width on the CRT faceplate (e.g. green CRT)
Mounting Configuration
Ceiling Mount
To install the projector in the Ceiling configuration, use BARCO'S
Ceiling Mount Kit (CM100) - Order Number R9827341 (with pulley)
or R9827342 (without pulley). Installation instruction is included
inside the kit.
Table Mount
BARCO offers a heavy-duty projection table with adjustable height
which allows the projector to be correctly positioned perfectly to the
installation requirements. Order Number - R9827740.
3-2
5975698 BARCOVISION 1609s 220198
Installation set-up
4
INSTALLATION SET-UP
WARNING :
Risk of electric shock !
Installation only by BARCO authorized service personeel
Access to Controls
Opening the top cover
Lock screws
During the projector set-up and installation it is necessary to open the top cover. Follow the procedure
as described below :
Turn the locking screw with a screwdriver or coin
counter clockwise;
Lift up and pivot the top cover.
WARNING :
The projector's top cover is not supported with
locking hinge. Open with care and support the cover
with your hand.
Removing the top cover
During some installations, it will be convenient to remove the top cover
from the projector totally.
Proceed as follows :
Loosen the lock screws by turning a quarter counter clockwise
with a screwdriver or coin and pull out the two hinge-joints.
Left up the top cover to remove.
Re-installing the top cover
To re-install the top cover on the projector :
Place the top cover on the projector until both hinges parts join
togheter.
Insert both hinge-joints.
Secure the locking screws by turning them clockwise with a
screwdriver or coin.
5975698 BARCOVISION 1609s 220198
4-1
Installation set-up
Scan Adaptation
The scan switches must be placed in the correct position which corresponds to the desired scanning configuration.
To change the scanning, it is necessary to remove the projector top cover and to open the protection plate.
For opening the projector's top cover, see 'Access to controls'.
WARNING !
TURN OFF PROJECTOR AND UNPLUG THE POWER
CORD BEFORE CHANGING THE SCAN DIRECTION.
Gaining access to the scan switches
Open the top cover and remove it from the
projector (see p.4-1);
Loosen the 3 lock screws;
Remove the 3 retaining screws on each
side of the cover plate;
Remove the fixation screw nearby the
fan;
Open the protection plate and pivot it forward (toward lenses).
Fixation screw
Lock screws
4-2
5975698 BARCOVISION 1609s 220198
Installation set-up
Horizontal Scan Switches
Three switches are used, one for each CRT. When changing the
horizontal scan, insure that all three switches are set in the same
position. See positions of the switches (diagram on next page) for
the corresponding projector configuration.
To set the scan switches :
Toggle the 3 horizontal scan inversion switches to
the correct positions.
+RUL]RQWDO
9HUWLFDO
GHIOHFWLRQVZLWFKHV
GHIOHFWLRQVZLWFK
5
%
*
Vertical Scan Switch
One vertical switch is used for the three CRT's.
To set the vertical scan switch :
Toggle the vertical scan inversion switch to the
correct position.
3URMHFWRUFRQILJXUDWLRQV6ZLWFKVHWWLQJV
)URQWFHLOLQJ
5
5HDUFHLOLQJ
*
5
%
*
SUHVVHG
SUHVVHG
SUHVVHG
)URQWWDEOH
5
%
QRWSUHVVHG
5HDUWDEOH
*
%
5
QRWSUHVVHG
*
%
SUHVVHG
QRWSUHVVHG
QRWSUHVVHG
After setting the scan switches, close the metal protection plate and
secure it with the retaining screws.
Close the top cover and reconnect the power cord to the wall outlet.
Note :
Switching over from Floor to Ceiling or vice versa requires a complete
re-adjustment of picture geometry and convergence.
To check the current positions of the scan switches, proceed
as follows:
Attention : This procedure can only be done after power (mains)
connection. So, first continue with the projector set-up
and the connections and then return to this procedure.
Switch on the projector. The projector starts up on the last
selected source.
Press the ADJUST.
Highlight 'SERVICE' by pushing the control disk up or down and
press the ENTER. The 'SERVICE MODE MENU' will be displayed.
ADJUSTMENT MODE
Select a path from
below:
GUIDED
RANDOM ACCESS
INSTALLATION
SERVICE
IRIS
source 1
Select with
or
then <ENTER>
<EXIT> to return
5975698 BARCOVISION 1609s 220198
4-3
Installation set-up
Highlight 'IDENTIFICATION' by pushing the control disk up or
down and press the ENTER.
SERVICE MODE
IDENTIFICATION
COPY A BLOCK
DELETEABLOCK
DELETEALL BLOCKS
CHANGEPASSWORD
CHANGE LANGUAGE
RUN TIME
DYNAMICASTIGMATISM
MORE...
Select with
or
then <ENTER>
<EXIT> to return
The projector will display the 'IDENTIFICATION SCREEN'.
This screen gives the current information about the projector configuration in the line entitled 'Config'.
VISION 1609s
Proj. address : 001
Soft. Version : 6.00
Config. : Ceiling
Front
Baudrate PC : 9600
Text : ON
Serial No. : 103589552
4-4
5975698 BARCOVISION 1609s 220198
Projector set-up
5
PROJECTOR SET-UP
The DIP switches on the controller board allow the
SET-UP of the projector :
*
8 DIP switches for the projector address setting.
*
1 DIP switch for the power up mode setting.
*
3 DIP switches for the baud rate for communication setting.
*
1 DIP switch for the password mode setting.
To gain access to the DIP switches :
*
Loosen the 3 screws on both sides (indicated on drawing below) of the frame.
*
Loosen the 3 screws on the rear side of the
metal frame.
*
Lift up the metal cover plate and pivot to the
lens side. The controller is mounted on the back
side
PASSWORD MODE
POWER UP MODE
PASSWORD REQUIRED
FOR ADJUSTMENT
ON
YES
OFF
NO
OPERATING MODE WHEN
POWER IS SWITCHED ON
ON
PLAYING
OFF
StdBY
BAUD RATE TABLE
TO COMPUTER
CODE
0
1
2
3
4
5
6
7
0 1
PROJECTOR ADDRESS
(sum)
SPEED
110
150
300
600
1200
2400
4800
9600
RESERVED
POWER UP MODE
PASSWORD MODE
BAUD RATE CODE
(sum)
128
64
32
16
8
4
2
1
1
2
3
4
2
1
1
2
3
4
5
6
7
8
1
2
3
4
5
6
7
8
StdBY
MAIN POWER
PROCESSOR CYCLES
I 2C SHORTED
BLOCK MATCH
ERROR
RCU
RCVDS
PC
PAUSE
OFF
5975698 BARCOVISION 1609s 220198
ON
5-1
Projector set-up
Setting the projector address
The projector's address may be set to any value between 0 and 255.
When the address is set, the projector can be controlled now by :
*
the RCU for addresses between 0 and 9.
*
a IBM PC (or compatible) or Apple MAC for addresses between 0
and 255.
Addressable with RCU
Addressable with PC, MAC
or workstation
Setting the address is a hardware SET-UP of your projector which
must be done during installation. Use the 8 DIP switches provided on
the controller board labelled 'Projector Address'.
Each DIP switch has its own decimal value. The sum of the values
associated to those DIP switches gives the address. As shown in
the table, if Switch No. 1 is set to ON, it represents a decimal value
of 128, Switch No.2 for 64, Switch No.3 for 32, and so forth.
In the given example, the projector address is set to 202 :
DIP switch No.
: 1 2 3 4 5 6 7 8
Position ON/OFF : 1 1 0 0 1 0 1 0
Sum : 1x128 + 1x64 + 0x32 + 0x16 + 1x8 + 0x4 + 1x2 + 0x1 = 202
Switch No
Value
1
2
128
64
3
32
4
5
6
7
8
16
8
4
2
1
2))
21
Factory preset address = 0
Note :
When the address button on the RCU is pressed, the projector will
display its own address on the screen. Once the address button is
pressed, to continue using your RCU, it is necessary to enter an
address, even when the displayed address is correct. Use the
numeric keys to enter the address.
For more information, please refer to the Owner's Manual of this
projector.
PROJECTOR
ADDRESS
001
5-2
5975698 BARCOVISION 1609s 220198
Projector set-up
Power-up mode
The projector can start up in two different modes. The start up mode
is determined by the position of DIP Switch No. 4 of another set of 8
DIP switches on the controller board (one set of 8 switches are used
for projector address setting).
Position of the DIP Switch No. 4 (power up mode) :
1
2
3
4
5
6
7
8
Power-up mode
ON : operational mode.
OFF : stand-by mode (Factory preset).
OFF ONOFF
ON
*
Operational mode
When the power switch on the rear of the projector is pressed, the
projector displays the last selected source if available, otherwise it
remains on that source number until the source becomes available.
The on screen indication is only available when the "Text" function
is set to "ON".
Source 2
Fh= 15.6 kHz
Fv= 50 Hz
*
Stand-By mode
When the power switch on the rear of the projector is pressed, the
projector starts up in the stand-by mode. The stand-by key on the RCU
is used to turn the projector ON and OFF.
Baud Rate for communication with a
computer
The communication speed between the projector and the computer
has 8 possible settings. With DIP Switch No. 6, No.7 and No.8 of the
8 DIP switches on the controller board, labelled as ‘Baud rate code
(sum)’, it is possible to select the baud rate (communication speed).
Each DIP switch has its own decimal value. The sum of the values
associated to those DIP switches gives the baud rate code. Each
baud rate code corresponds an communication speed.
0
Position of DIP switches and baud rate codes :
Binary Baud rate code
000
0
001
1
010
2
011
3
100
4
101
5
110
6
111
7
Speed
110
150
300
600
1200
2400
4800
9600
4
Baud rate
DIP switches
2
1
1
1
2
3
4
5
6
7
8
OFF ON
Factory preset baud rate = 9600
More information about computer communication with the projector
is available in the Projector Control Software manual.
Password mode
5975698 BARCOVISION 1609s 220198
5-3
Projector set-up
With DIP Switch No.5 of the second set of 8 DIP switches on the
controller board, the projector adjustments can be protected with a
password. When the password feature is enabled, the user has to
enter a password before he can enter the adjustment mode (For more
information about password setting and reprogramming the password, see Installation adjustment).
When the password menus are disabled (adjust mode is unprotected), the adjust mode can be selected by pressing the <ADJUST>
key. This position of the DIP switch is useful for qualified service
technicians because they do not need a password to enter the adjust
mode.
Position of DIP Switch No.5 :
ON
: password mode enabled.
OFF : password mode disabled.
0
Password
mode
1
1
2
3
4
5
6
7
8
OFF ON
Factory preset password mode : OFF.
5-4
5975698 BARCOVISION 1609s 220198
AC power connection
6
AC POWER CONNECTION
AC Power (mains) cord connection
Use the supplied cord to connect your projector to the wall outlet. Plug
the female power connector into the male connector at the back of
the projector.
9120
9ROW
,0 $;
$ PS
)5(4
+]
1
, 6 5
7 82
6 5
5
,
56,1
56287
,5
(7 2 0( 5
5(027(
685
This projector may be connected to an IT-power system. The ITpower system is a power distribution system having no direct
connection to earth. Instead, the exposed conductive parts of the
electrical installation are earthed.
Preparing your power cord
Mains lead (power cord) with CEE7 plug
As the colors of the wires in the mains lead of this apparatus may
not correspond with the colored markings identifying the terminals in
your plug, proceed as follows:
*
The yellow/green wire is ground and must be connected to the
terminal in the plug which is marked by the letter E or by the safety
earth symbol
or colored yellow and green.
*
The blue wire is neutral and must be connected to the terminal
marked with the letter N or colored black.
*
The brown wire is the line and must be connected to the terminal
marked with the letter L or colored red.
The wires of the delivered mains lead (power cord) are colored in
accordance with the following code :
Yellow and Green :
Ground (Earth).
Blue
:
Neutral.
Brown
:
Live.
Power cord with an ANSI 73.11 plug
The wires of the delivered mains lead (power cord) are colored in
accordance with the following code :
Yellow and Green : Ground (Earth).
White
Black
: Neutral.
:
Live.
5975698 BARCOGRAPHICS 1609s 220198
6-1
AC power connection
AC Power check
Check the power voltage which is determined by the Art. No. on the
identification label pasted on the backside of the projector.
ART.NR : RXXXXXXX
SER.NR ; RXXXXXXX
Projectors with the Art. No. R9002240 must be connected to a 230
VAC power source.
Projectors with the Art. No. R9002249 must be connected to a 120
VAC power source.
When the power voltage is different from that of the wall outlet,
proceed to AC Input power voltage adaptation of the projector.
1
, 65
5 6,1
782
65
56287
5
,
,5
(720
(5
5(027(
AC Input power (mains) voltage adaptation
Attention !
The BARCOGRAPHICS 1209s - R9002240 leaves the factory to
operate on a mains (power) input of 230 Vac.
The BARCOGRAPHICS 1209s - R9002249 leaves the factory to
operate on a mains (power) input of 120 Vac.
Adaptation of the power input of the projector between 230 Vac and
120Vac or vice versa is possible.
Follow the procedure as described below to adapt the voltage :
1 WARNING: turn off the projector and be sure the AC Power Cord
is unplugged from the wall outlet before starting the procedure !
2 Open the top cover (see 'Access to controls' on p.4-1).
3 Unscrew the retaining screws of the power input protection plate.
4 Remove the power input protection by sliding it a little backwards
and lifting it up.
Retaining screws
5 Pull out the 'Power selector plug' and re-insert it as illustrated in
drawing, depending on the AC power of the wall outlet in the room.
6 Pull out the fuses and place the correct fuses in their sockets. See
the table below for the correct fuses.
230V operation
230V
120V operation
2xT5A/250V
120V
2xT10A/250V
7 Re-install the protection plate. Insert the plate until the pins fit into
the grooves of the bottom plate. The right side of the plate must
be pushed behind the metal frame. The notch fits around the bolt.
Secure the correct position by turning in the 3 screws.
6-2
5975698 BARCOGRAPHICS 1609s 220198
AC power connection
Fuses
Warning !
For continued protection against fire hazard :
AC power
Fuses
Order Number
*
Replace with the same type of fuse.
230 Vac
T6.3A/250V (2x)
R314145
*
Refer replacement to qualified service personnel.
120 Vac
T10A/250V (2x)
R314154
Switching on the projector
The projector is switched ON and OFF using the power (mains)
switch ON/OFF.
*
If the switch is pressed in
*
If the switch is Not pressed in : OFF
: ON
The projector can be started up in the 'Operational mode' (image
displayed) or in the 'Stand-by mode', depending on the position of the
'Power-up' DIP switch on the controller board. This DIP switch is set
during installation by a qualified technician. If you want to change this
start up mode, call a qualified technician.
Power indication lamp :
OFF
: no power.
Green : projector in operational mode.
Red
: projector in stand-by mode.
When switching on the projector, with the power switch or via the
stand-by key on the RCU, the projector can start up in two ways if
the "CRT run in cycle" option is switched OFF :
*
A full white image (projector warm up) or
*
Immediately image display.
The way of starting up can be set in the service mode.
Starting up with a full white image
When the projector is set to start up with a full white image, the
"Projector warm up" menu will be displayed for 30 seconds.
Start up with "Warm up period"
If no action is taken, a white image will be displayed for 20 minutes.
This white image will be shifted on the faceplate of the CRT to avoid
a CRT burn-in.
It is also possible to adjust the dimensions for that white image to avoid
scanning on the edges of the CRT's. Push the control disk up or down
to adjust the vertical amplitude and push the control disk to the right
or to the left to adjust the horizontal amplitude.
During this warm up period, it is possible to interrupt this white image
projection by pressing EXIT. The "Projector warm up" menu will be
re-displayed for another 30 seconds but with the remaining time
indicated.
If EXIT is pressed again, the remaining warm up period will be skipped.
During the warm up period, every 30 seconds a text box with the
remaining time will be displayed on the screen for 2 seconds. This
text box will be displayed every time on another place to avoid a CRT
burn-in.
5975698 BARCOGRAPHICS 1609s 220198
PROJECTOR WARM UP
A FULL WHITE PATTERN WILL BE
GENERATED FOR 20 MINUTES.
FOR IMMEDIATE USE OF THE
PROJECTOR, PRESS
<EXIT>.
WARNING : SKIPPING THIS
PROCEDURE CAN REDUCE
THE INITIAL PICTURE
QUALITY OF THE PROJECTED
IMAGE.
THIS OPTION CAN BE
DISABLED IN THE SERVICE
MENU
REMAINNG
PROJECTOR
WARM UP
TIME
18.5MIN
PLEASE USE
<EXIT> TO
LEAVE THIS
PROCEDURE
6-3
AC power connection
If a key, other than EXIT, is pressed, a text box with the following text
will be displayed :
"Please use <EXIT> to leave this procedure."
Start up without "Warm up period"
If EXIT is pressed, the warm up period will be skipped and the projector
is immediately ready for use.
Warning : Skipping this warm up procedure can reduce the
initial picture quality of the projected image.
6-4
5975698 BARCOGRAPHICS 1609s 220198
Source connections
7
SOURCE CONNECTIONS
Signal input connection
The following signals can be connected to the projector through the
inputs on the back panel of the projector :
*
Composite Video
*
S-Video
*
RGB
*
Component Video
*
RGB with Tri-level sync
*
Component video with Tri-level sync
Port No
1
2
3257
3257
5*%+9
352-(&72502'(
32: (5 0$ ,1 6
9,'(2
*5((1RSHUDWLRQDO
&RPS+V\QF
32575(027(
&20081,&$7,21
9V\QF
5('VWDQGE\
3257
3257
69,'(2
2))
5
Projector input
21
2))
RKP
RKP
%
*
21
Numeric button
Composite Video
S-Video / Composite Video
Description of input signal
1
2
S-video : Y/C (luma/chroma).
The Composite video can also be connected to Port 2. It can be
selected inside the "Picture Tuning" menu. Please refer to the
Owner's Manual of this projector.
3
RGB
3
R, G and B with composite sync on Green, separate composite
sync or with separate Horizontal and Vertical sync.
4/5
RGB
4 or 5
R, G and B with composite sync on Green, with separate
composite sync or with separate Horizontal and Vertical sync.
R-Y, Y, B-Y with composite sync on Y, or with separate
composite sync or with separate Horizontal and Vertical sync.
4/5
Component video
6
4/5
RGB with Tri-level sync
7
R, G and B with Tri-level sync on Green or with separate Trilevel sync or with separate Horizontal and Vertical Tri-level
sync.
R-Y, Y, B-Y with Tri-level sync on Y; or with separate Trilevel sync or with separate Horizontal and Vertical Tri-level
sync.
Only available when the optional Tri-level sync module is installed.
4/5
Component video
with Tri-level sync
8
Connecting a Composite Video source to
Port 1
Composite video signals coming from e.g. a VCR, OFF air signal
decoder can be connected to Port 1.
3257
3257
5*%+9
9,'(2
352-(&72502'(
32:(50$,16
*5((1RSHUDWLRQDO
&RPS+V\QF 9V\QF
32575(027(
5('VWDQGE\
3257
3257
&20 0 81,&$7,21
69,'(2
2))
To select the video input :
5
*
%
2))
21
21
RKP
RKP
Press the digit button 1 on the RCU or the local keypad.
Composite
video
75 W Termination Switch for Video
WRQH[WSURMHFWRURU
WRDPRQLWRU
Terminate the video input of the projector using the 75Ω switch next
to the video input, when the projector operates alone or when the
projector is the last unit in a loop-through configuration.
The switch is set to "ON" : signal terminated.
The switch is set to "OFF" : signal not terminated.
TV tuner, e.g. TVDM40 stereo
Audio amplifier
9&5
5975698 BARCOVISION 1609s 220198
7-1
Source connections
Connecting a S-Video (or Composite Video)
source to Port 2
Separate Y-luma/C-chroma signals for higher quality playback of
Super VHS signals can be connected to Port 2 . A composite video
signal can also be connected to this port.
4 pin connector configurations:
For S-video:
Pin 1: earth(ground) luminance
Pin 2: earth(ground) chrominance
Pin 3: luminance signal(Y)
1Vpp ±3dB
Pin 4: chrominance signal(C)
300mVpp ±3dB
To select the S-video input :
For video:
Pin 1: earth(ground) video
Pin 2: not connected
Pin 3: video signal
Pin 4: not connected
3
1
2
4
3257
3257
5*%+9
9,'(2
Press the digit button 2 on the RCU or the local keypad.
32575(027(
&20081,&$7,21
32:(50$,16
352-(&72502'(
*5((1RSHUDWLRQDO
&RPS+V\QF 9V\QF
5('VWDQGE\
3257
3257
69,'(2
2)) 21
2)) 21
5
In case of using Port 2 for connecting the Composite Video, the
selection of this source have to be done inside the "Picture Tuning"
menu. Please refer to the Owner's Manual.
*
RKP
RKP
%
75 Ω Termination
Switch
/XPD&KURPD
75 W Termination Switch for S-video
WRQH[WSURMHFWRURU
WRDPRQLWRU
Terminate the S-video input of the projector using the 75 Ω switch next
to the S-video input when the projector operates alone or when the
projector is the last unit in a loop-through configuration.
9&569+6
$XGLRDPSOLILHU
The switch is set to "ON" : signal terminated.
The switch is set to "OFF" : signal not terminated.
Connecting a RGB Analog source to Port 3
Connect a RGB Analog signal via an interface (e.g. RGB 120MHz
interface, part number 98 26570) to Port 3. RGB analog input with
automatic sync detection (Separate H and V sync inputs, with
composite sync input or with sync signals on green) and automatic
polarity detection.
Pin configuration of the D9 (male) connector of the Analog input :
1
not connected
2
ground RGBS
3
RED
4
GREEN
5
BLUE
6
ground RGBS
7
ground RGBS
8
Horizontal /composite sync
9
Vertical sync
3257
3257
5*%+9
9,'(2
352-(&72502'(
32:(50$,16
*5((1RSHUDWLRQDO
&RPS+V\QF
32575(027(
9V\QF
5('VWDQGE\
3257
3257
&20081,&$7,21
2))
5
21
*
%
69,'(2
2)) 21
21
RKP
RKP
$1$ /2*,17(5)0+]
,1387
%
+
9
2))
5
*
,13
,13
RGB 120MHz interface
RKPWHUP LQYHU
To select the RGB analog Input :
Press the digit button 3 on the RCU or the local keypad.
361
Locations of the Termination Resistors and Switches
on the RGB Input Auto Sync Tracking Module
When changing a switch position or removing a resistor, turn off the
projector and unplug the power cord from the wall outlet.
S2 Blue in Green (ON=yes)
75 W Termination resistors
In case of chaining (loop-through) the projectors, the 75Ω line
termination resistors must be removed from the RGB Input Auto Sync
Tracking Module when the projector is NOT the last unit in the chain.
In case of a stand-alone projector, do not remove the resistors.
75 Ω resistors on the module :
line terminated.
75 Ω resistors removed
line not terminated.
:
R101
Vsync
R81
Hsync
R41
(Blue)
R21
(Green)
R1
(Red)
S1 Force Negative Sync
(ON=yes)
Line termination 75 Ω resistors
7-2
5975698 BARCOVISION 1609s 220198
Source connections
Procedure to remove the line termination resistors :
1 Turn off the projector and unplug the projector power cord.
2 Remove the top cover from the projector.
3 Remove the RGB Input Auto Sync Tracking Module from the main
frame.
4 Unsolder and remove the resistors.
To remove the RGB Input Auto Sync Tracking Module, press the
module locks and lift up the module handles
Blue in Green Switch on the RGB Input Auto Sync Tracking
Module
RGB Input Auto Sync Tracking Module
Blue characters are difficult to read, therefore the blue text will be
displayed as cyan so that the readability becomes better.
Switch in the ON position : Blue in Green active.
Switch in the OFF position : Blue in Green disabled.
WARNING : Leaving the switch in the ON position will result in
abnormal color balance of the projected image.
Force Negative Sync on the RGB Input Auto Sync
Tracking Module
Switch in the ON position : the sync pulses must be negative.
Switch in the OFF position : the sync polarity will be automatically
detected.
Connecting a RGB Analog source to Port 4/5
3257
3257
5*%+9
9,'(2
32:(50$,16
352-(&72502'(
*5((1RSHUDWLRQDO
RGB analog input terminals with separate H and V sync inputs,
composite sync input or sync signals on green can be connected to
the projector via Port 4/5. The projector automatically detects where
the sync signal is located.
&RPS+V\QF
32575(027(
&20081,&$7,21
9V\QF
5('VWDQGE\
3257
3257
69,'(2
2))
5
An interface is recommended when connecting a computer and local
monitor to the projector. BARCO provides the following interfaces
:
* Universal Analog Interface - Order no. : R9826100.
* RGB 120 MHz Analog Interface - Order no. : R9826570.
* VGA interface - Order no. : R9828070 (230V), R9828079 (120V)
* MAC interface - Order no. : R9828050 (230V), R9828059 (120V)
* MAGIK interface - Order no. : R9828129 & R9828128 (120V)
R9828120 & R9828121 (230V)
21
%
*
21
2)) 21
RKP
RKP
$1$/2*,17(5)0+]
,1387
%
+
9
2))
*
5
,13
,13
R KP WHUP
, QWHUIDFH
LQYHU
To select the RGB input :
Press the digit button 4 or 5 on the RCU or the local keypad.
363
Connecting a Component Video source to
Port 4/5
3257
9,'(2
352 -( &72 50 2' (
32:(50$,16
*5 ((1 RSH UDWL RQD O
32 57 5(027(
A component video (R-Y, Y, B-Y) with sync signals can be
connected to the projector via Port 4/5. The projector automatically
detects where the sync signal is located.
3257
5*%+9
&R P S + V\Q F 9V \Q F
5( 'VWD QGE \
3 25 7
32 57 &20081,&$7,21
6 9,' (2 2) )
5
*
%
2 ))
21
21
RKP
R KP
An HDTV interface is recommended when connecting a computer
and local monitor to the projector. The HDTV Kit Order number :
R9828040.
To select the component video input :
Press the digit button 6 on the RCU or the local keypad.
9&5 +' 79SOD\HU
$ XGLRDP SOLILHU
5975698 BARCOVISION 1609s 220198
7-3
Source connections
Connecting a RGB Analog source with Trilevel sync to Port 4/5 (option)
3257
3257
5*%+9
9,'(2
352-(&72502'(
32:(50$,16
*5((1RSHUDWLRQDO
&RPS+V\QF
32575(027(
&20081,&$7, 21
9V\QF
5('VWDQGE\
3257
3257
69,'(2
2))
5
*
%
2))
21
21
RKP
RKP
RGB analog input terminals with Tri-level sync input or with Tri-level
sync on green can be connected to the projector via Port 4/5. The
projector detects automatically where the sync signal is located. This
feature requires an optional Tri-Level Sync Module - Order No.
R9828040.
To select the input :
VCR HDTV player
Press the digit button 7 on the RCU or the local keypad.
Connecting a Component Video source with
Tri-level sync to Port 4/5 (option)
Audio amplifier
359
Component video inputs with Tri-level sync signal can be connected
to the projector via Port 4/5. The projector detects automatically
where the sync signal is located. This feature requires an optional
Tri-Level Sync Module - Order No. R9828040.
To select the input :
Press the digit button 8 on the RCU or the local keypad.
Peripheral equipment
Connecting a RCVDS 05 source selector to the
projector.
* Up to 20 inputs with a RCVDS05 and up to 90 inputs can be
accommodated when multiple RCVDS source selectors are linked
via a Expansion Module.
* Serial communication with the projector.
* Remote control buttons on the RCVDS05 to control the projector
(source selection and analog settings).
* The selected source number will be displayed on a 2-digit display
and the selected input modules will be indicated with a LED on the
rear.
The order numbers for the RCVDS05 source selector :
RCVDS05 230 V
R9827880
RCVDS05 120 V
R9827889
For more information about the use of the RCVDS05, consult the
RCVDS05 Owner's Manual - order number : R5975765.
Connecting a VS05 source selector to the projector.
The VS05 can switch up to 5 Composite Video sources, 3 S-Video
Sources and 1 RGB analog or component Video source to the
projector. In addition, the audio signal associated with the source, can
be switched to an audio amplifier.
VS05 order no. : R9827890.
For more information about the use of the VS05, consult the VS05
Owner's Manual - order number : R5975245.
Connecting an IR Remote Receiver 800 to the projector
This infra-red Remote Receiver makes it possible to control the
projector from another room. There is a communication cable between the IR Remote Receiver and the projector. The control
information from the RCU can now be sent to the IR Remote Receiver
800. The IR Remote Receiver 800 displays the selected source on a
7-segment display.
IR Remote Receiver 800 order number : R9827515.
7-4
5975698 BARCOVISION 1609s 220198
Installation adjustment mode
8
INSTALLATION ADJUSTMENT MODE
Access to Installation Adjustment Mode
It will be necessary to perform several mechanical adjustments while
in the Installation Adjustment Mode. It will be required to open and
remove the projector's top cover in order to gain access to the
adjustment points.
ADJUSTMENT MODE
Select a path from
below:
GUIDED
RANDOM ACCESS
INSTALLATION
SERVICE
IRIS
To enter into the installation adjustment mode :
1 Press ADJUST to start up the adjustment mode.
2 Push the control disk up or down to highlight the path
INSTALLATION in the "Adjustment mode" menu and then press
ENTER.
WARNING
RISK OF ELECTRICAL SHOCK
NO USER ADJUSTABLE PARTS
INSIDE
3 A warning will be displayed on the screen. If you are a qualified
and authorized service person, press ENTER to start up the
installation mode. Otherwise, press EXIT to return.
THE FOLLOWING
INSTALLATION MENUS
ARE RESERVED TO,
AND TO BE PERFORMED ONLY
BY BARCO PERSONNEL, OR
BARCO AUTHORIZED DEALERS
When entering the installation mode, the projector will automatically
switch to the internal pattern on 15 kHz/50 Hz.
4 When the password mode is active, you will be requested to enter
the 4 digit password.
IF QUALIFIED, PRESS
<ENTER> TO CONTINUE, OR
IF NOT, <EXIT> TO RETURN.
Enter the digits with the numeric keys on the RCU or the local
keypad.
Example : Password as 2 3 1 9
For each digit entered, a 'X' appears on the screen under the
displayed text 'enter password'.
enter
password
xxxx
If the entered password is correct, you get access to the
'Installation Adjustment Mode'.
197
If the entered password is wrong, The message "Wrong password!!!" will be displayed. The projector stays on the previous
selected item.
Factory programmed password :
0000
enter
password
xxxx
197
Overview flowchart of the Installation Adjustment Mode
Adjustment Mode
Installation
Projector Distance
Optical Lens Focusing
CRT Projection Angle Adjustment
5975698 BARCOVISION 1609s 220198
Raster Centering
Scheimpflug Adjustment
8-1
Installation adjustment mode
Important : Access to adjustments
The top cover of the projector should be removed in order to gain
access to the adjustments.
Projector Distance
On the screen, a drawing will be displayed together with parameters
indicating a correct installation position.
FHLOLQJ
3'
To change the screen width :
$
1 Push the control disk to the left or to the right to highlight the item
SW in the "Projector Distance 1" menu and then press TEXT.
If ENTER is pressed, the "Optical Lens Focusing" will be displayed.
SURMHFWRU
VFUHHQ
If EXIT is pressed, the projector will return to the previous menu.
2 After TEXT is pressed, the next menu "Projector Distance 2" will
be displayed on the screen. It allows the user to change the
Screen width.
3 Push the control disk to the left or to the right to highlight the digit
needed to be changed, and enter the desired digit with the numeric
keys on the RCU or the local keypad.
4 Press ENTER to confirm the changes. The projector will re-display
the "Projector Distance 1" menu with updated values for the three
parameters.
5 Press ENTER to continue with the "Optical Lens Focusing".
A = Correction value
PD= Perpendicular distance between screen and projector
SW= Screen width
SW = 2.6 m
PD= 3.64m
A=12 cm
Select with arrow keys; <TEXT> to reprogram
<ENTER> to continue; <EXIT> to return.
WARNING: ONLY FOR STANDARD PROJECTORS !!
If EXIT is pressed, the projector will return to the previous menu.
The same applies to the PD (projector distance). You can use the
above-mentioned procedure to obtain a correct updated value of SW
(screenwidth) after entering a new value of PD (projector distance).
SCREENWIDTH = 2 , 6 0 m
Select with arrow keys; reprogram with numeric keys and
then <ENTER> to confirm.
Maximum screenwidth = 6 m
Maximum proj. distance = 8,1 m.
Optical Lens Focusing
The optical focusing procedure is performed separately for each
lens. The appropriate CRT will be switched on as the user proceeds
through the optical focusing adjustment sequence.
OPTICAL LENS FOCUSING
Each lens has two focus adjustment points, one at the rear of the lens
and one at the front. The center of the projected image is focused by
loosening the wing nut at the rear end of the lens and rotating the
lens barrel until the center of the image is clearly focused. The corners
of the projected image are focused by loosening the wing nut at the
front end of the lens and rotating the lens barrel until the corners of
the image are clearly focused. Repetition of these adjustments may
be necessary to optimize optical focusing.
1. LOOSEN THE NUT ON THE
REAR OF THE XXXX LENS,
ROTATE THE LENS BARREL
TO FOCUS THE CENTER
OF THE IMAGE,
THEN TIGHTEN THE NUT
2. LOOSEN THE NUT ON THE
FRONT OF THE XXXX LENS
AND ROTATE THE FRONT
SECTION OF THE LENS TO
FOCUS THE CORNERS OF THE
IMAGE, THEN TIGHTEN THE NUT.
<ENTER> to continue
<EXIT> to return
OPTICAL LENS FOCUSING
Press ENTER to continue. After finishing focusing of the three lenses,
press ENTER to enter the Raster centering.
Press EXIT to return to operational mode.
Press ADJUST key to return to operational mode.
Center focusing
1. LOOSEN THE NUT ON THE
REAR OF THE XXXX LENS,
ROTATE THE LENS BARREL
TO FOCUS THE CENTER
OF THE IMAGE,
THEN TIGHTEN THE NUT
2. LOOSEN THE NUT ON THE
FRONT OF THE XXXX LENS
AND ROTATE THE FRONT
SECTION OF THE LENS TO
FOCUS THE CORNERS OF THE
IMAGE, THEN TIGHTEN THE NUT.
150
<ENTER> to continue
<EXIT> to return
OPTICAL LENS FOCUSING
150
1. LOOSEN THE NUT ON THE
REAR OF THE XXXX LENS,
ROTATE THE LENS BARREL
TO FOCUS THE CENTER
OF THE IMAGE,
THEN TIGHTEN THE NUT
2. LOOSEN THE NUT ON THE
FRONT OF THE XXXX LENS
AND ROTATE THE FRONT
SECTION OF THE LENS TO
FOCUS THE CORNERS OF THE
IMAGE, THEN TIGHTEN THE NUT.
<ENTER> to continue
<EXIT> to return
Corner focusing
8-2
5975698 BARCOVISION 1609s 220198
Installation adjustment mode
Raster Centering
The raster must be centered on the CRT faceplate of each tube,
therefore, it is necessary to look into the lenses.
RASTER CENTERING
Caution : To avoid eye discomfort while performing these adjustments, reduce the contrast and gradually increase the brightness
level until the raster becomes visible behind the image.
Warning : In order to ensure maximum CRT
longevity and to avoid CRT damage, do not shift
the raster outside the phosphor area of the CRT.
Press ENTER to display the raster on the green CRT.
CONTRAST LEVEL IS REDUCED
AND BRIGHTNESS INCREASED
TO MAKE THE RASTER
VISIBLE ON THE FACE PLATE
OF EACH CRT.
USE THE ARROW KEYS
TO CENTER THE RASTER
ON THE GREEN, RED AND
BLUE CRT RESPECTIVELY
<ENTER> to continue
<EXIT> to return
forbidden area
projected raster
Look into the green lens and shift the raster with the control stick until
it is centered in the middle of the CRT faceplate.
Press ENTER to activate the raster on the Red CRT faceplate.
Shift the Red raster with the control stick until the raster is centered
on the CRT faceplate.
Press ENTER to activate the raster on the Blue CRT faceplate.
Shift the Blue raster with the joy stick until the raster is centered on
the CRT faceplate.
crt faceplate border
phosphor border
234
Press ENTER to continue with the CRT projection angle adjustment.
Press EXIT to return to Optical focusing.
Press ADJUST to return to Operational mode.
FRUUHFWUDVWHUSRVLWLRQ
ZURQJUDVWHUSRVLWLRQ
233
5975698 BARCOVISION 1609s 220198
8-3
Installation adjustment mode
CRT Projection Angle Adjustment
The projection angle of the red and blue CRT's is dependent on the
desired size of the projected image. If the centers of green, blue and
red do not coincide, the CRT projection angle must be adjusted.
NOTE : Never try to correct this misalignment with the shift
correction or the static convergence controls. These controls
may only be applied to correct small errors which cannot be
corrected by the CRT angle adjustment.
Note: The Horizontal Shift and Vertical Shift for Red and Blue
should be set near 50%.
CRT PROJECTION ANGLE
ADJUSTMENT
CRT PROJECTION ANGLE IS
THE FIRST STEP OF STATIC
CONVERGENCE ADJUSTMENT.
IT IS CRITICAL THAT THE
RASTERS ARE CENTERED ON
THE CRT FACE PLATES
PRIOR TO PERFORMING
THIS STEP.
...
<ENTER> to read more
<EXIT> to return
Be sure that the rasters are centered on the CRT faceplate.
CRT PROJECTION ANGLE
ADJUSTMENT
DURING THIS PROCEDURE,
RED ON GREEN AND THEN
BLUE ON GREEN CROSSHAIRS
WILL BE DISPLAYED
TO ALLOW THE RED AND
BLUE CRTS TO BE ALIGNED
WITH THE GREEN CRT.
Press ENTER to start the CRT angle adjustment procedure.
Press ENTER to continue with the crosshairs alignment.
Press EXIT to return to the previous menu.
Press ADJUST to return to Operational mode.
LOOSEN BOLTS A AND B
TO PIVOT THE RED CRT,
AND BOLDS C AND D
TO PIVOT THE BLUE CRT.
<ENTER> to continue
<EXIT> to return
Loosen bolts A, B and C to pivot the red CRT until the center of the
Red image and the center of the Green image coincide. When the
angle of the red CRT is corrected, tighten the four bolts.
Press ENTER to continue with blue and green crosshairs.
Press EXIT to return to the CRT projection angle adjustment menu.
CRT
PROJECTION ANGLE
ADJUSTMENT
Red crosshair
Green crosshair
Align crosshairs
<ENTER> continue
<EXIT> to return
Move the red CRT towards
the green CRT
Red crosshair
Green crosshair
Move the red CRT to the
outside, away from the
green CRT
F E
9120
,0$;
)5(4
B
A
9 R OW
$ P S
+ ]
1
, 6 5
56,1
8-4
C
D
7 82
65
56287
5
,
,5
(720(5
5(027(
5975698 BARCOVISION 1609s 220198
Installation adjustment mode
Loosen bolts D, E and F to pivot the blue CRT until the center of the
Blue image and the center of the Green image coincide. When the
angle of the blue CRT is corrected, tighten the four bolts.
Press ENTER to continue with the diagonal focusing menu.
Press EXIT to return to the CRT projection angle adjustment.
CRT
PROJECTION ANGLE
ADJUSTMENT
Blue crosshair
Green crosshair
Move the blue CRT to the outside, away from the green
CRT
Align crosshairs
<ENTER> continue
<EXIT> to return
Blue crosshair
Green crosshair
Move the blue CRT towards
the green CRT
Projection angle correctly aligned for screen width SW1.
The same projection angle is mis-aligned for new screen width SW2.
Re-alignment is necessary. Each screen width change requires
readjustment of the projection angle.
SW2
SW1
5975698 BARCOVISION 1609s 220198
(SW1 > SW2)
8-5
Installation adjustment mode
Scheimpflug Adjustment (Diagonal image
focusing)
With the diagonal image focusing corrections, it is possible to obtain
uniform focus for the total projected image.
DIAGONAL IMAGE FOCUSING
These corrections must be repeated for each colour. The Diagonal
image focusing is repeated 3 times, first for green, then for red and
then for blue.
1. TURN THE SCREW MARKED;;
TO FOCUS THE IMAGE DIAGONALLY from LEFT (bottom) TO
RIGHT (top).
2. TURN THE SCREW MARKED ;;
TO FOCUS THE IMAGE DIAGONALLY from LEFT (top) TO RIGHT
(bottom)
<ENTER> to continue
<EXIT> to return
First, be sure that the CRT projection angle is correctly adjusted,
otherwise it is not possible to obtain proper overall focus of the image.
Press ENTER to start the green adjustment.
Press EXIT to return to CRT Projection Angle Adjustment.
Adjustment procedure :
:$51,1*72$'-8676&+(,03)/8*&255(&7,216$72$
),567/226(17+(&255(6321',1*6(&85,7<1876%72%
6&+(,03)/8*$'-8670(17,6/,0,7('
$
$
$
$
$
$
%
%
%
%
%
%
%/8(
*5((1
5('
352-(&725)52179,(:
:$51,1*:$51,1*
:$51,1*:$51,1*
:$51,1*:$51,1*:$51,1*
B5
B4
:$51,1*:$51,1*:$51,1*
B6
Red CRT Lens
Loosen first the security screws (see images opposite and above.)
Example : diagonal focusing of the green image.
Equalize diagonally the focus from left (bottom) to right (top) by turning
screw A3 of the projected colour.
Equalize now diagonally the focus from left (top) to right (bottom) by
turning screw A4 located under the green lens.
right
left
right
left
8-6
GREEN
A3
A4
RED
A5
A6
BLUE
A1
A2
A6
A5
A4
A3
A2
A1
5975698 BARCOVISION 1609s 220198
Installation adjustment mode
+
+
+
+
Repeat the same procedure for the red and blue image using the
corresponding screws.
To optimize the image focusing, repeat the optical lens focusing.
When the scheimpflug corrections are correctly adjusted, secure
this position by fastening the security screws on both sides of each
lens.
LENS
CORNER FOCUSING
Warning : When the security screws are tightened, it is not possible
to change the scheimpflug correction.
CENTER FOCUSING
DIAGONAL IMAGE FOCUSING
from left top to right bottom
DIAGONAL IMAGE FOCUSING
from left bottom to right top
+
+
E R OW$ E R OW$ E R OW$ +
+
E R OW$ E R OW$ E R OW$ BLUE IMAGE
RED IMAGE
GREEN IMAGE
e.g. : Turning bolt A 5 will influence the diagonal focus for Red from left bottom to right top
After finishing the Installation Adjustment Procedures, the main menu
returns on the screen. You are now able to start the alignment
procedure for the projector.
For detailed information about these adjustments, please refer to the
Owner's Manual.
ADJUSTMENT MODE
Select a path from
below:
GUIDED
RANDOM ACCESS
INSTALLATION
SERVICE
IRIS
Select with
or
then <ENTER>
<EXIT> to return
enter
password
xxxx
197
5975698 BARCOVISION 1609s 220198
8-7
Installation adjustment mode
8-8
5975698 BARCOVISION 1609s 220198
Appendix A: BARCO ceiling mount support
A
BARCO CEILING MOUNT SUPPORT
This appendix gives only an overview of the contents of the
installation guidelines and some overview drawings.
The installation guidelines for the BARCO ceiling mounting support
can be ordered from BARCO. The order number: R5975693.
Contents of the installation guidelines
Overview drawing of the total system
&(17(5XSSHUVXSSRUW
1. Mounting instructions for the upper support to the ceiling
a. Position of the upper support on the ceiling
1
2
3
b. Mounting of the 4 screwed rods on the upper support
2. Projector placement on lower support
a. Projector placement on support
b. Location of controls for projector-position correction
3. Mounting instructions of the cord to lift up the projector
0$;/(1*+7&0
a. Mounting the cord support on the upper support
b. Cord insertion between the upper and lower support
c. Cord fixation
4. Lifting up and fixing the lower support (with projector) on the
screwed rods
',67$1&(6&5((1)5217
833(56833257 3'FP
5. Alignment of the projector-support assembly
a. Projector water-level adjustment
3'
b. Adjustment "projector axis perpendicular" to the screen surface
c. Projector movement forward or backward
Exploded view of BARCO ceiling mount
support
CEILING FIXATION FOR PROJECTOR
5975698 BARCOVISION 1609s 220198
A-1
Appendix A: BARCO ceiling mount support
Projector-position corrections
* Water-level adjustment
D
* Projector axis adjustment
C
A-2
5975698 BARCOVISION 1609s 220198
Appendix B: G2 adjustment
B
G2 ADJUSTMENT
Once the on-screen menu "G2 ADJUSTMENT" is displayed, proceed
as follows :
*$'-8670(17
Use the potentiometers
on the G2-ADJ. module
to set the screen grid
voltage for Red,
Green and Blue.
Adjust until the LED
on the corresponding
output amplifier is
turned off.
<EXIT> to return
1
* Remove the top cover from the projector.
* A green LED is mounted on each of these amplifiers.
When selecting the G2 adjustment menu, these green LEDs must
be out. If not, follow the next procedure to adjust the G2 :
1 open both metal cover by loosening the retaining screws on both
sides and pivot the covers to the front side of the projector;
2 adjust the G2 potentiometers very slowly with a screwdriver until
the LED of the corresponding amplifier just stops illuminating.
Repeat the adjustment for the other colors;
3 once the three G2 potentiometers have been correctly adjusted,
close both metal covers and secure with the retaining screws.
Green LEDs
2
Retaining screws
3
Red
Green
Blue
After finishing the adjustments :
Press ENTER to continue with the "SERVICE" menu.
Press EXIT to return to the "SERVICE" menu.
Press ADJUST to return to Operational mode.
5975698 BARCOVISION 1609s 220198
B-1
Appendix B: G2 adjustment
B-2
597698 BARCOVISION 1609s 220198
Gamma corrections
C
GAMMA CORRECTIONS
When entering the gamma corrections, a warning will be displayed
:
"RISK OF INCORRECT ADJUSTMENT OF THE PROJECTOR.
THE GAMMA CORRECTIONS ARE FACTORY ADJUSTED USING
AN ACTAS COLOR ANALYSER ! THEREFORE, ONLY QUALIFIED
INSTALLATION OR SERVICE PERSONNEL SHOULD PERFORM
THESE ADJUSTMENTS ! "
If you are qualified, press the <ENTER> key to continue.
Gamma Corrections
Three items can be selected inside the "Gamma Corrections" menu:
the Blue Gamma Correction, the R & B midlights and the factory preset.
To carry out the Blue Gamma Correction :
1 Push the control disk up or down to highlight the item
BLUE GAMMA CORRECTION in the menu and then press
ENTER.
If EXIT is pressed, the projector will return to the Service menu.
2 After ENTER is pressed, a text box with message "Adjust with
arrow key" will be displayed on the screen.
WARNING
RISK OF INCORRECT
ADJUSTMENT OF THE
PROJECTOR.
THE GAMMA CORRECTIONS ARE
FACTORY ADJUSTED USING AN
ACTAS COLOUR ANALYSER !
THEREFORE, ONLY QUALIFIED
INSTALLATION OR SERVICE
PERSONNEL SHOULD PERFORM
THESE ADJUSTMENTS !
<ENTER> TO CONTINUE
<EXIT> TO RETURN.
GAMMA CORRECTIONS
BLUE GAMMA CORRECTION
Adjust slope with é or ê
Breakpoint with ç or è
R & B MIDLIGHTS
Adjust red with é or ê
blue with ç or è
FACTORY PRESET
Select with é or ê
then <ENTER>;
<EXIT> to return.
3 Push the control disk up or down to adjust the slope, a text box
with a bar scale (Min to Max) will be displayed to visualise the
magnitude of the correction.
4 Push the control disk to the left or to the right to adjust the
breakpoint, a text box with a numeric bar scale (0-99) will be
displayed to visualise the magnitude of the correction.
5 Press ENTER to return to the "Gamma Corrections" menu.
Adjust with arrow key
BLUE GAMMA
SLOPE
Min
Max
BLUE GAMMA
BREAKPOINT
50
5975698 BARCOVISION 1609s 220198
C-1
Gamma Corrections
To carry out the Red and Blue Midlights Correction :
1 Push the control disk up or down to highlight the item
R & B MIDLIGHTS in the menu and then press ENTER.
If EXIT is pressed, the projector will return to the Service menu.
2 After ENTER is pressed, a text box with message "Adjust with
arrow key" will be displayed on the screen.
3 Push the control disk up or down to adjust the Red Midlights, a text
box with a bar scale (0-16) will be displayed to visualise the
magnitude of the correction.
4 Push the control disk to the left or to the right to adjust the Blue
Midlights, a text box with a bar scale (0-16) will be displayed to
visualise the magnitude of the correction.
5 Press ENTER to return to the "Gamma Corrections" menu.
GAMMA CORRECTIONS
BLUE GAMMA CORRECTION
Adjust slope with é or ê
Breakpoint with ç or è
R & B MIDLIGHTS
Adjust red with é or ê
blue with ç or è
FACTORY PRESET
Select with é or ê
then <ENTER>;
<EXIT> TO RETURN.
Adjust with arrow key
RED
MIDLIGHTS
8
BLUE
MIDLIGHTS
8
To set the parameters back to the factory preset values :
*
*
Push the control disk up or down to highlight the item
FACTORY PRESET in the menu and then press ENTER.
Press EXIT to return to the Service menu.
GAMMA CORRECTIONS
BLUE GAMMA CORRECTION
Adjust slope with é or ê
Breakpoint with ç or è
R & B MIDLIGHTS
Adjust red with é or ê
blue with ç or è
FACTORY PRESET
Select with é or ê
then <ENTER>;
<EXIT> to return.
C-2
5975698 BARCOVISION 1609s 220198
Form Approved
Bureau Budget No. 45-R0338
MATERIAL SAFETY DATA SHEET
MANUFACTURER'S NAME AND FSCM (Federal Supply Code for Manufacturer's)
BARCO N.V.
EMERGENCY PHONE NO.
32-56-368211
SECTION I
ADDRESS (Number, Street, City, State, and ZIP Code)
Noordlaan 5 B-8520 KUURNE
CHEMICAL NAME AND SYNONYMS
Ethylenglycol & Glycerol
TRADE NAME AND SYNONYMS
Cooling liquid 512334
CHEMICAL FAMILY
Polyalcohols
FORMULA
FEDERAL STOCK NUMBER (FSN)
GROSS WEIGHT (LBS)
C2H6O2+C3H8O3
OUTSIDE PACKAGE DIMENSIONS (Inches)
MIL-STD-1341/NATIONAL FIRE PROTECTION ASSOCIATION STD 704M SIGNAL
FLAMMABILITY....................
HEALTH..................
REACTIVITY.................
SECTION III
PHYSICAL DATA
SECTION II - HAZARDOUS INGREDIENTS
PAINTS, PRESERVATIVES, AND
SOLVENTS
TRESHOLD LIMIT
VALUE (Units)
%
ALLOYS AND METALLIC COATINGS
PIGMENTS
BASE METAL
CATALYST
ALLOYS
VEHICLE
METALLIC COATINGS
SOLVENTS
FILLER METAL
PLUS COATING OR CORE FLUX
ADDITIVES
OTHERS
SPECIFIC HAZARD.............
%
TRESHOLD LIMIT
VALUE (Units)
%
TRESHOLD LIMIT
VALUE (Units)
OTHERS
HAZARDOUS MIXTURES OF OTHER LIQUIDS, SOLIDS, OR GASES
BOILING POINTS (°C.)
201°C
SPECIFIC GRAVITY (H2O=1)
VAPOR PRESSURE (mm Hg.)
3 mm Hg
PRECENT VOLATILE
BY VOLUME (%)
VAPOR DENSITY (AIR=1)
2.2
EVAPORATION RATE
(.............................=1)
1.15
SOLUBILITY IN WATER
SECTION IV - FIRE AND
EXPLOSION HAZARD DATA
APPEARANCE AND ODOR
DD
FLASH POINT (Method used)
FLAMMABLE LOWER EXPLOSIVE LIMIT
LIMITS
UPPER EXPLOSIVE LIMIT
EXTINGUISHING MEDIA
SPECIAL FIRE FIGHTING PROCEDURES
UNUSUAL FIRE AND EXPLOSION HAZARDS
FORM
1 JUN 71
1813 *
GPO 794/043/30
S/N 0102-026-1080
SECTION V
HEALT HAZARD DATA
TRESHOLD LIMIT VALUE
EFFECTS OF OVEREXPOSURE
EMERGENCY AND FIRST AID PROCEDURES
STABILITY
SECTION VI
REACTIVITY DATA
100ppm
CONDITIONS TO AVOID
UNSTABLE
STABLE
X
INCOMPATABILITY (Materials to avoid)
HAZARDOUS DECOMPOSITION PRODUCTS
HAZARDOUS
POLYMERIZATION
MAY
OCCUR
X
CONDITIONS TO AVOID
WILL NOT
OCCUR
SECTION IX
SPECIAL
PRECAUTIONS
SECTION VIII - SPECIAL
PROTECTION INFORMATION
SECTION VII
SPILL OR LEAK PROCEDURES
STEPS TO BE TAKEN IN CASE MATERIAL IS RELEASED OR SPILLED
Rinse with water
WASTE DISPOSAL METHOD
RESPIRATORY PROTECTION (Specific type)
VENTILATION
LOCAL EXHAUST
SPECIAL
MECHANICAL (General)
OTHER
PROTECTIVE GLOVES
EYE PROTECTION
OTHER PROTECTIVE EQUIPMENT
PRECAUTIONS TO BE TAKEN IN HANDLING AND STORING
Harmful if swallowed
Keep out of the reach of
children
OTHER PRECAUTIONS
To avoid from oxidants
THE INFORMATION CONTAINED HEREIN IS BASED ON DATA CONSIDERED ACCURATE. HOWEVER, NO WARRANTY IS EXPRESSED OR IMPLIED REGARDING THE ACCURACY OF THESE
DATA OR THE RESULTS TO BE OBTAINED FROM THE USE THEREOF.
VENDOR ASSUMES NO RESPONSABILITY FOR INJURY TO VENDEE OR THIRD PERSONS PROXIMATELY CAUSED BY THE MATERIAL IF REASONABLE SAFETY PROCEDURES ARE NOT ADHERED TO AS STIPULATED IN THE DATA SHEET. ADDITIONALLY, VENDOR ASSUMES NO
RESPONSABILITY FOR INJURY TO VENDEE OR THIRD PERSONS PROXIMATELY CAUSED BY
ABNORMAL USE OF THE MATERIAL EVEN REASONABLE SAFETY PROCEDURES ARE FOLLOWED. FUTHERMORE, VENDEE ASSUMES THE RISK IN HIS USE OF THE MATERIAL.
S/N 0102-026-1080
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising