20140516_3A81Y41100000_DDR
DDR-38
中文
GB
Version 1
"Made for iPod," "Made for iPhone," and "Made for iPad" mean that an electronic accessory has been designed to connect specifically to iPod,
iPhone, or iPad, respectively, and has been certified by the developer to meet Apple performance standards. Apple is not responsible for the
operation of this device or its compliance with safety and regulatory standards. Please note that the use of this accessory with iPod, iPhone, or iPad
may affect wireless performance.
Made for
● iPhone 5s
● iPhone 5
● iPhone 5c
● iPad Air
● iPad mini with Retina display
● iPad (4th generation)
● iPad mini
● iPod touch (5th generation)
Contents
Controls ........................................................................... 3-6
Using the radio for the first time .......................................... 7
Operating your radio ........................................................... 8
Selecting a station - DAB .................................................... 9
Secondary services - DAB .................................................. 9
Display modes – DAB ....................................................... 10
Finding new stations - DAB ............................................... 11
Manual tuning - DAB ......................................................... 12
Signal strength display - DAB ........................................... 12
Dynamic Range Control (DRC) - DAB .............................. 13
Prune stations-DAB .......................................................... 14
Operating your radio - FM auto-tune ................................ 15
Manual tuning - FM .......................................................... 16
Display modes- FM ........................................................... 17
Setting FM auto(stereo) / mono ........................................ 18
Scan sensitivity setting-FM ............................................... 19
Presetting stations-DAB/ FM ............................................ 20
Recalling a preset station-DAB/FM ................................... 21
iPod/ iPhone/ iPad docking ............................................... 22
Navigating your iPod/ iPhone/ iPad .................................. 23
Playing a file on your iPod/iPhone/ iPad ........................... 23
Search function ................................................................. 23
Listening to Bluetooth music ............................................. 24
Pairing your Bluetooth device for the first time ................. 24
Pairing with your Bluetooth device before ........................ 25
Disconnecting your Bluetooth device ............................... 26
Setting the alarm .......................................................... 27-29
To view the alarm settings ................................................ 30
GB
Cancelling alarms ............................................................. 30
Controlling alarms in standby ........................................... 31
Snooze function ................................................................ 31
Sleep function ................................................................... 32
Setting the clock manually ........................................... 33-34
Setting the clock format .................................................... 35
Display backlight dimmer .................................................. 37
EQ function ....................................................................... 38
Setting up my EQ profile ................................................... 39
Mute function .................................................................... 40
Software version ............................................................... 40
USB socket for software upgrade ..................................... 41
System reset ..................................................................... 42
Headphone socket ............................................................ 43
Auxiliary input socket ........................................................ 43
Line Out socket ................................................................. 43
Charging with USB socket ................................................ 44
Specifications .................................................................... 45
Control
1. LCD display
2. Speaker
GB
3. iPod/ iPhone/ iPad docking
4. Switch for docking cover
5. Menu button
6. Select button
7. Tuning control
8. Standby button
9. Alarm 2 button/ Fast-forward button
10. Mode button
11. Bluetooth Pair button
12. Snooze button
13. Alarm 1 button/ Play/ Pause button
14. Preset button
15. Auto tune button/ Rewind button
16. Dimmer button
17. Volume button
18. EQ button
19. Sleep button
20. Info button
21. DC power in jack
22. Socket for USB charging
23. Line out jack
24. Headphone jack
25. Aux in jack
26. Socket for software upgrade
27. Telescopic aerial for DAB+ / FM
Note:
For the sake of clarity, the instructions for the use of the controls throughout this instruction manual show the buttons on the radio. The buttons on
the remote can be used if you prefer.
Controls (remote control)
GB
A . iPod mode button
B . Standby button
C . Volume down button
D . Volume up button
E . Preset button
F . Info button
G . EQ button
H . Snooze button
I . Fast-forward button
J . Select button
K . Alarm button
L . Sleep button
M . Tuning down button
N . Play/ pause button
O . Light (Dimmer) button
P . Menu button
Q . Rewind button
R . Tuning up button
S . Bluetooth mode / pair button
T . Aux in mode
U . DAB mode
V . Mute button
W. FM mode button
Using the radio for the first time
1. Place your radio on a flat surface.
2. Fully extend the telescopic aerial located on the rear of your radio.
3. Insert the adaptor plug into the DC socket located on the rear of your radio. Plug the adaptor
into a standard mains outlet. The display will show “Welcome to Digital Radio” for a few seconds.
After s short time, the current time will appear on the display.
4. If no stations are found, “0:00” will be displayed. Press the Standby button to turn on your radio
and it will find a DAB clock radio stations. It may be necessary to relocate your radio to a
position giving better reception and carry out a scan to find stations as described in later
sections.
IMPORTANT:
The mains adaptor is used as the means of connecting the radio to the mains supply. The mains
socket used for the radio must remain accessible during normal use. In order to disconnect the
radio from the mains completely, the mains adaptor should be removed from the mains outlet
completely.
Welcome to
Digital Radio
Operating your radio
1. Press the Standby button to switch on your radio. The display will show “Scanning” for a few
seconds.
GB
Scanning...
24
When first switched on, the radio will be in DAB mode. Then the first station in the list of stations
found during scanning will be played. The display will show the station name on the display.
After each use the radio will remember the last mode used and then switch on in that mode the
next time that it is used. If the radio has been used before, the last used station will be selected.
If no signals are found then “No Service Available” will be displayed and it may be necessary to
relocate your radio to a position giving better reception. You should then carry out a scan to find
stations.
Note:
that radio station name and frequency displays shown in this user guide may differ from those
that you see on your radio. Broadcasters may change radio station names that are transmitted,
and the frequencies used for DAB and FM radio stations may not be the same in all parts of the
country.
Selecting a station - DAB
1. Press the Standby button to switch on your radio.
DAB Mode
2. Press and release the Mode button until the DAB mode is selected. The display will show the
name of the radio station currently selected.
3. Rotate the Tuning control to step through the list of available stations.
4. When the desired station name appears on the display, press and release the Select button to
select the station. The display will show 'Connecting' while your radio finds the new station.
5. Adjust the Volume control to the required setting.
Station list
<BBC Radio 2
>
BBC Radio 2
Connecting...
Note:
If after selecting a station, the station is not found it may be necessary to relocate your radio to a
position giving better reception.
Secondary services - DAB
1. Certain radio stations have one or more secondary services associated with them. If a station
has a secondary service associated with it then the secondary service will then appear
immediately after the primary service as you press the Tuning.
2. To tune to the secondary service, press and release the Select button. Most secondary services
do not broadcast continually and if the selected service is not available, the radio will re-tune
to the associated primary service.
Station list
<BBC Radio 5 Live
>
Station list
<BBC R5LiveSportX
>
Display options - DAB
GB
Your radio has a range of display options when in DAB mode:1. Press and release the Info button to cycle through the various options. All display options except
the text display will revert to the clock display after about 10 seconds.
a. Scrolling text
Displays scrolling text messages such as artist/track name,
phone in number, etc.
b. Programme type
Displays type of station being listened to e.g. Pop, Classic,
News, etc.
c. Multiplex Name
Displays the name of the DAB multiplex to which the current
station belongs.
d. Time and date
Displays the current time and date.
e. Frequency & channel
Displays frequency and channel number for the currently tuned
DAB station.
f . Bit rate & audio type
Displays the digital audio bit rate and audio type for the
currently tuned DAB station.
g. Signal strength
Displays the signal strength for the currently tuned DAB
station. The open block in the signal strength graph shows the
minimum signal strength needed for good DAB reception. The
signal blocks will go up or down showing the changing signal
strength as you adjust the aerial or the radio position.
a
BBC Radio 2
Now playing on the r
b
BBC Radio 2
Pop Music
c
BBC Radio 2
BBC National DAB
d
BBC Radio 2
10:28
8-1-2013
e
BBC Radio 2
12B 225.648MHz
f
BBC Radio 2
128kbps / DAB
g
BBC Radio 2
10
Finding new stations - DAB
From time to time, new DAB radio stations may become available. Or you may have moved to
a different part of the country. In this case you may need to cause your radio to scan for new
stations.
1. Press and release the Menu button until the Advanced DAB menu shows on the display.
2. Press the Auto tune button to scan for new stations. Your radio will perform a scan of the Band III
DAB channels. As new stations are found, the station counter on the right-hand side of the
display will increase and stations will be added to the list.
11
Scanning...
24
Manual tuning - DAB
GB
Manual tuning allows you to tune your radio to a particular DAB frequency in Band III. Any
new stations found will be added to the station list. This function can also be used to assist the
positioning of the aerial or the radio to optimize reception for a specific channel or frequency.
1. Press the Menu button until the Advanced DAB menu shows on the display and then release
the button.
2. Rotate the Tuning control until the display shows 'Manual Tune'.
3. Press and release the Select button to enter the manual tuning mode.
4. Rotate the Tuning control to select the desired DAB channel.
5. Press and release the Select button. The open block in the signal strength graph shows the
minimum signal strength needed for good DAB reception. The signal blocks will go up and
down showing the changing signal strength as you adjust the telescopic aerial or the radio
position. Any new radio stations found on the tuned DAB multiplex will be added to the list
stored in the radio.
DAB
<Manual Tune
>
Manual Tune
<12B 225.648MHz
>
12B 225.648MHz BBC
6. Press and release the Select button to return to normal tuning mode.
Signal strength display - DAB
1. Press and release the Menu button until the display shows signal strength. The open block in
the signal strength graph shows the minimum signal strength needed for good DAB reception.
BBC Radio 2
The signal blocks will go up and down showing the changing signal strength as you adjust the
aerial or the radio position.
12
Dynamic Range Control (DRC) - DAB
The DRC facility can make quieter sounds easier to hear when your radio is used in a noisy
environment.
There are three levels of compression:
DRC Off No compression applied. (default)
DRC High Maximum compression applied.
DRC Low Medium compression applied.
1. Press the Standby button to switch on your radio.
2. Press and release the Mode button until the DAB band is selected.
3. Press and release the Menu button until the Advanced DAB menu shows on the display.
4. Rotate the Tuning control until 'DRC Value' appears on the display. Press and release the
Select button. The display will show the current DRC value which will be marked with an asterisk.
5. Rotate the Tuning control to select the required DRC setting (default is off).
6. Press and release the Select button to confirm the setting. After several seconds the display
will return to the normal radio display.
Note:
Not all DAB broadcasts are able to use the DRC function. If the broadcast does not support
DRC, then the DRC setting in the radio will have no effect.
13
DAB
<DRC Value
DRC Value
>
*
<DRC off
>
DRC Value
<DRC high
>
DRC Value
<DRC low
>
Prune stations - DAB
GB
Over time, some DAB services may stop broadcasting, or may change location and then not be
able to receive a station. In order to remove such stations from the DAB station list, the Prune
stations function will delete the DAB stations from your station list that can no longer be received.
Stations which cannot be found or which have not been received for a very long time are shown
in the station list with a question mark.
1. Press the Standby button to switch on your radio.
2. Press and release the Mode button until the DAB mode is selected.
3. Press and release the Menu button until the Advanced DAB menu shows on the display.
4. Rotate the Tuning control until 'Prune' appears on the display. Press and release the Select
button.
5. Press the Tuning Up or Down buttons to highlight 'Yes'. Press and release the Select button to
cause the stations list to be pruned, eliminating unavailable stations.
DAB
<Prune
>
Prune?
No <Yes>
Prune?
<No> Yes
6. If you do not wish to prune stations highlight 'No' in step 5 and then press and release the
Select button. The display will revert back to the previous display.
Note:
If you have moved to a different part of the country you should also carry out a search for new
stations (please see the section 'Finding new stations' in previous section).
14
Operating your radio - FM auto-tune
1. Fully extend the telescopic aerial located on the rear of your radio.
FM Mode
2. Press the Standby button to switch on your radio.
3. Press and release the Mode button until the FM band is selected.
4. Press and release the Auto tune button to cause your radio to search from low frequency to
high frequency and to stop automatically when it finds a station of sufficient strength.
5. After a few seconds the display will update. The display will show the frequency of the signal
found. If the signal is strong enough and there is RDS data present then the radio may display
the station name.
6. To find other stations press the Auto tune button as before. When the end of the waveband is
reached, your radio will recommence tuning from the opposite end of the waveband.
7. Adjust the Volume to the required setting.
8. To switch off your radio, press the Standby button.
Note:
If you find that FM reception is poor, try repositioning the aerial. If you find that an FM broadcast
has a lot of background hiss, this may often be reduced by setting the radio into Mono reception
mode for the current FM station. Please refer to the later section "Stereo / Mono setting - FM".
15
87.50MHz
Scanning...
Manual tuning - FM
1. Fully extend the aerial located on the rear of your radio.
GB
FM Mode
2. Press the Standby button to switch on your radio.
3. Press and release the Mode button until the FM band is selected.
87.50MHz
4. Rotate the Tuning control to tune to a station. The frequency will change in steps of 50kHz. If
the radio is tuned to a station of sufficient signal strength with RDS information present, then
the display may change to show the station name.
5. When the waveband end is reached the radio will recommence tuning from the opposite waveband
end.
6. Set the Volume to the desired setting.
7. To switch off your radio press the Standby button.
16
Display options - FM
Your radio has a range of display options for FM mode:The Radio Data System (RDS) is a system in which inaudible digital information is transmitted
in addition to the normal FM radio programme. RDS offers several useful features. The following
are available on your radio. All display options except the text display will revert to the clock
display after about 10 seconds.
1. Press and release the Info button to cycle through the various options.
a. Scrolling text
Displays scrolling text messages such as artist/ track name,
phone in number, etc.
b. Programme type
Displays type of station being listened to e.g. Pop, Classic,
News, etc.
c. Multiplex name
Displays the name of the FM multiplex to which the current
stations belongs.
d. Audio type
Displays the audio type for the currently tuned FM station.
e. Time & date
Displays the current time and date.
Note:
If no RDS information is available, the radio will be unable to display the station name, scrolling
text and programme type information.
17
99.70 MHz
The best variety of
99.70 MHz
Pop Music
99.70 MHz
Mono
99.70 MHz
10:08
11-1-2013
Stereo / Mono setting - FM
GB
Your radio will play stereo FM broadcasts in stereo provided that the received signal is of
adequate strength. However, as a stereo signal becomes weaker the audio signal will become
poorer. It may be preferable to force the radio to play the station in mono in order to reduce the
level of background hiss.
1. Press the Standby button to switch on your radio.
FM
2. Tune to the required FM radio station as previously described.
<FM Aud
3. Press and release the Menu button until the Advanced FM menu shows on the display.
4. Rotate the Tuning controls until 'FM Audio' appears on the display. Press and release the
Select button.
5. To switch to mono to reduce the hiss from a weak FM signal rotate the Tuning control until
'Mono' appears on the display. Press and release the Select button to confirm the setting. The
current audio setting will be marked with an asterisk.
FM Audio
<Mono
>
*
>
FM Audio
<Auto
>
6. Alternatively to return to stereo rotate the Tuning control until 'Auto' appears on the display.
Press and release the Select button to confirm the setting.
18
Scan sensitivity setting - FM
Your radio includes a local/distant option for the auto-scan function. By setting the radio to the
'local' scan option, weaker signals from more distant transmitters can be ignored by the radio,
making stronger signals easier to find.
1. Press and release the Standby button to switch on your radio.
2. If needed, press and release the Mode button until the FM band is selected.
3. Press and release the Menu button until the Advanced FM menu shows on the display.
4. Rotate the Tuning control until 'FM Scan Zone' shows on the display. Press and release the
Select button to enter the scan sensitivity adjustment mode. The current setting will be marked
with an asterisk.
5. Rotate the Tuning control to switch between 'Local' (Strong stations only) and 'Distant' (All
stations) options on the lower line of the display. The Distant option will allow the radio to find
weaker signals when scanning.
6. Press and release the Select button to confirm your selection. The Local or Distant setting is
stored in the radio and remains in force until changed or until a System Reset.
19
FM
<FM Scan Zone
>
FM Scan Zone
<Distant
*
>
FM Scan Zone
<Local
>
Presetting stations - DAB and FM
GB
You may store your preferred DAB and FM radio stations to the preset station memories. There
are 20 memory presets in your radio 10 for DAB and 10 for FM. Presets are remembered by your
radio in the event of a power failure.
The procedure for setting presets and using them to tune stations is the same for FM and DAB
modes, and is described below.
1. Press the Standby button to switch on the radio.
2. Press the Mode button to select the DAB or FM waveband.
Preset 1
stored
3. Tune to the required station as previously described.
4. Press and hold the Preset button until the display shows ‘Preset store.’
5. Rotate the Tuning control to select your desired preset number. Press the Select button to store
the currently tune station. The display will show, for example ‘Preset 1 stored.’ Repeat this
procedure for the remaining presets.
Note:
Stations stored in preset memories may be overwritten by following the above procedure.
20
Recalling a preset station- DAB and FM
1. Press the Standby button to switch on the radio.
2. Press and release the required waveband by pressing the Mode button.
3. Press and release the Preset button and ‘Preset Recall’ shows on the display.
4. Rotate the Tuning control to select the desired preset station. Press the Select button to tune to
the chosen preset station stored in the preset memory.
Note:
The display will show 'Preset Empty' if no station has been stored to that preset.
21
BBC Radio 2
Connecting...
iPod/ iPhone/ iPad docking
GB
Your radio has an iPod/ iPhone/ iPad dock facility which allows you to play digital audio files and
video soundtracks held on your iPod / iPhone/ iPad using the radio’s loudspeakers.
Your radio uses the lightning connector developed for use with iPods/ iPhone/ iPad and is made
for the following models:
● Phone 5s
● iPhone 5
● iPhone 5c
● iPad Air
● iPad mini with Retina display
● iPad (4th generation)
● iPad mini
● iPod touch (5th generation)
Important:
To avoid possible damage to your iPod/ iPhone/ iPad, do not connect the iPod/ iPhone/ iPad
which are not listed as compatible models above.
1. Right click the iPod/ iPhone/ iPad cover switch to open the cover. 2. Carefully place your iPod/ iPhone/ iPad onto the dock connector.
3. Press the Standby button to switch on your radio.
4. To select the iPod mode press the Mode button until “IPod” shows on the display. If your iPod/
iPhone/ iPad was previously playing, it will switch on and continue playing from where it was
previously stopped.
Note:
Your radio is able to recharge your iPod/ iPhone/ iPad internal battery in all the modes. Your
iPod/ iPhone/ iPad will use its backlight settings as configured. If these need changing, use the
Settings menu on your iPod/ iPhone/ iPad.
22
Navigating your iPod/ iPhone/ iPad
You can only navigate full menus of your iPod/ iPhone/ iPad on the device itself.
Playing a file on your iPod/ iPhone/ iPad
1. If your iPod/ iPhone/ iPad was previous playing, when you connect the device to DDR-38, it will
continue playing from where was previously stopped
2. Adjust the volume to the required setting using the Volume control on your radio.
3. To pause playback press the Play / Pause button. To resume playback press the Play / Pause
button again.
4. iPod/ iPhone/ iPad do not have a Stop button (they use the Pause function).
Search function
1. While the iPod/ iPhone/ iPad is playing, press and hold the Fast-forward or Rewind buttons to
move through the current track. Release the button when the desired point in the track is reached.
2. Press and release either the Fast-forward or Rewind buttons to start playing the next or previous
track.
23
Listening to Bluetooth music
GB
You need to pair your Bluetooth device with your radio before you can auto-link to play/ stream
Bluetooth music through your DDR-38. Paring creates a `bond' so two devices can recognize
each other.
Pairing your Bluetooth device for the first time
1. Press the Mode button until the Bluetooth mode is selected. The Bluetooth icon on the panel
will flash.
Blutooth
2. Activate Bluetooth on your device according to the device's user manual to link to your DDR-38.
3. Once connected, the Bluetooth icon will remain illuminated. You can now play the music in your
Bluetooth-enabled device via DDR-38.
4. Make sure to turn down the volume from your Bluetooth device.
Note:
1) If there are 2 Bluetooth devices searching for DDR-38, it will show its availability on both devices.
However, if one device links with the DDR-38 first, then the other Bluetooth device won't find
the DDR-38 on its list.
2) If your Bluetooth-enabled device is temporarily disconnected to your DDR-38. As long as the
disconnection last within 1 minutes, your device can re-connect with your radio again
automatically. If the disconnection last more than 1 minutes, then you need to manually
reconnect your device again to the radio. Be aware that during the period of disconnection, no
other Bluetooth device can pair or link with your radio.
24
3) If ‘DDR-38’ shows in your Bluetooth device list but your device cannot connect with it, please
delete the DDR-38 item from your list and pair the device with DDR-38 again following the
steps described previously.
4) The effective operation range between the system and the paired device is approximately 10
meters (30 feet).
5) Any obstacle between the system and the device can reduce the operational range.
6) Different playback functions are available in Bluetooth mode(i.e. Play/ Pause/ next track/previous
track/ fast-forward/ rewind). However, Bluetooth-enabled devices vary in how they respond to
the playback dependent upon the model.
Pair with your Bluetooth device before
If your Bluetooth device already paired with DDR-38 previously, the unit will memorize your
Bluetooth device, but it does not support the automatic reconnection, reconnect with this product
following the steps below.
DDR-38 can memorize up to 8 sets of Bluetooth device, when the memory exceed this amount,
the earliest paired device will be over written.
1. Press and release the Pair button to enter the Bluetooth device memory. Then rotate the Tuning
control to find the desired memorized Bluetooth device and press the Select button to connect
to the required Bluetooth device.
2. Alternatively, repeatedly press and release the Pair button to have access to the stored Bluetooth
device and press the Select button to connect to the required Bluetooth device.
25
GB
Disconnecting your Bluetooth device
Press the Mode button to select any bands other than Bluetooth band or press and hold the Pair
button to disconnect the link.
If you disconnect the Bluetooth device when you are in Bluetooth mode, the LED light for
Bluetooth icon will then start to flash indicating deactivation of Bluetooth.
Alarms
Your radio has 2 separate alarms which can be set to wake you to DAB, FM radio or buzzer
alarm. Each alarm can be set to sound once, daily, on weekdays or at weekends. The alarms can
be set whether the radio is on or in standby mode. In the event of a power interruption your radio
has a built in memory chip that will maintain your alarm settings for when the power is restored.
Note:
If no buttons are pressed for 10 seconds, the radio will exit the alarm setup.
26
Setting an alarm
1. Press and release the Alarm 1 button. ‘Alarm 1 Setup’ will show on the display. Or Press and
release the Alarm 2 button. ‘Alarm 2 Setup’ will show on the display.
Alarm 1 Setup
2. Press the Select button to enter the alarm setup wizard. Alarm status will flash on the display.
3. Rotate the Tuning control to select On or Off. If Off is selected any current setting for that
alarm will be cancelled.
4. With ‘On’ selected, press and release the Select button to cause the alarm hour digits to flash
on the display.
5. Rotate the Tuning control to choose the desired hour for the alarm and then press the Select
button to cause the alarm minute digits to flash on the display. If the radio has been set to the
12 hour clock format, there will also be an option here for setting AM or PM for the alarm time.
6. Rotate the Tuning control to choose the desired minute for the alarm and then press the Select
button. The alarm duration will flash on the display.
7. Rotate the Tuning control to choose the alarm duration. Choose between 15, 30, 45, 60 or 90
minutes.
8. Press and release the Select button to enter the alarm duration. The alarm source option will
flash on the display.
27
Alarm 1 Wizard
Alarm On
Alarm 1 Wizard
On time
09:00
Alarm 1 Wizard
On time
09:30
Alarm 1 Wizard
Duration
60
GB
9. Rotate the Tuning control to choose the desired source for the alarm (DAB, FM, Buzzer or
iPod). Press the Select button when the desired source alarm is highlighted on the display.
For which ever radio mode is selected, the radio alarm may be set to any of the stations
which have been stored as presets or to the station last listened to.
10. If setting the alarm to a radio option, rotate the Tuning control to choose either last listened or
from presets 1-10.
Note:
that you can only set the alarm to use a preset which has already been stored.
11. Press and release the Select button to confirm the selection. The alarm day option will flash
on the display.
12. Your alarm can be set to sound once, daily, weekdays and weekends.
Once - Will sound at one time only.
Daily - Will sound every day.
Weekdays - Will sound only on weekdays.
Weekends - Will sound only on weekends.
Alarm 1 Wizard
Source
Buzzer
Alarm 1 Wizard
Soucre DAB
Alarm 1 Wizard
Last listened
Alarm 1 Wizard
1: BBC Radio 4
Alarm 1 Wizard
Once
13. Rotate the Tuning control to choose the day option and then press and release the Select
button to confirm the setting.
● If setting alarms to daily, weekdays or weekends proceed to point 18.
14. If selecting the alarm to once you will need to set the day, month and year options as
described below.
28
15. Rotate the Tuning control to select the correct day and then press the Select button to
confirm the setting.
16. Rotate the Tuning control to select the correct month and then press the Select button to
confirm the setting.
17. Rotate the Tuning control to select the correct year and then press the Select button to
confirm the setting.
18. Rotate the Tuning control to choose the desired volume and press the Select button to
confirm the setting. Your radio will show 'Alarm Saved' and will exit the alarm setting
procedure.
Note:
1) Active alarms are indicated in the display by the alarm 'A' symbol. If the radio cannot connect
to the radio station, the buzzer alarm will be used instead. The alarm volume will start softly
and gradually increase in level every few seconds. The alarm will sound for the selected
duration unless cancelled.
2) when you are in Bluetooth or iPod mode, you can only use remote control to set the alarm.
29
Alarm 1 Wizard
Date
9-1-2013
Alarm 1 Wizard
Date
9-1-2013
Alarm 1 Wizard
Date
9-1-2013
Alarm
Saved
A
To view the alarm settings
1. Press and release the Alarm button. 'Alarm 1 Setup' will show on the display.
GB
Alarm 1 Setup
2. Or press and release the Alarm 2 button to select alarm number 2. 'Alarm 2 Setup' will show on
the display.
3. Press and release the Select button to enter the settings for the chosen alarm. You may use
the Tuning controls to modify any particular setting if desired, using the Select button to enter
the modification.
When the alarm sounds
The alarm will sound at the selected times for up to 90 minutes unless cancelled. The alarm
duration used for the alarm will be as specified during the alarm setting procedure.
Alarm off
The alarm icon will flash on the screen and the radio will automatically switch back to standby
mode when the selected alarm time has elapsed.
To cancel an alarm, press the Standby button to return to standby mode.
30
Controlling alarms in standby
When your radio is in standby, the alarms can be controlled using the Alarm button. This avoids
the risk of disturbance to someone who is asleep.
1. To change the states of the alarms when in standby, press and release the Alarm 1 button for
alarm 1 or Alarm 2 button for alarm 2.
2. Rotate the Tuning control. The display will cycle through alarm disabled and alarm enabled.
Alarm 1 Setup
Alarm On
Alarm 1 Setup
Alarm Off
3. Press and release the Select button to confirm the alarm setting. You may use the Tuning
controls to modify any particular setting if desired, using the Select button to enter the modification.
Snooze function
1. When the radio or buzzer alarm sounds, press and release the Snooze button. This will silence
the alarm for the selected number of minutes. The Snooze duration can be adjusted between
5 and 10 minutes in 5 minute increments. The default setting is 5 minutes.
2. If you wish for longer snooze duration, press the Snooze button again to select other snooze
option. Then the Snooze symbol 'Z' will flash. Press the Snooze button again to view the
remaining snooze time.
3. To cancel the snooze function, press and release the Standby button.
31
Z
Snooze
5 minutes
Sleep function
GB
Your radio can be set to turn off after a preset time has elapsed. The sleep setting can be
adjusted between 15 and 90 minutes. Ensure your radio is switched on.
1. To set the desired sleep time, press and release the Sleep button to enter the sleep setup.
2. Repeatedly press and release the Sleep button to select the desired sleep time. The sleep
settings available are 15, 30, 45, 60 or 90 minutes. A further press will cause the sleep timer to
be set to 'off' which will cancel the sleep function. Alternatively the Tuning control may be used.
3. Press the Select button to confirm the setting. The display will exit the sleep options. The sleep
symbol 'S' will show on the display.
4. Your radio will switch off after the preset sleep time has elapsed.
5. To cancel the sleep timer and switch off your radio before the chosen sleep time has elapsed,
press the Standby button. To cancel the sleep timer without switching off your radio, repeatedly
press the Sleep button until ' Sleep off' is displayed.
Set sleep time
15 minutes
Set sleep time
30 minutes
Set sleep time
Sleep off
99.75 MHz
[No RadioText]
S
6. When the sleep time has been set you may view the remaining sleep time. Press the Sleep
button. The remaining sleep time will show on the display.
32
Setting the clock manually
Your radio will set its clock automatically using the DAB or FM radio signal. If no signal is
available and you need to set the time manually, please follow the procedure shown below.
1. Press the Standby button to switch on your radio.
2. Press and release the Menu button until the Advanced menu shows on the display.
3. Rotate the Tuning control until 'System Setting' appears on the display. Press and release the
Select button.
DAB
<System Setting
>
System Setting
<Time
>
4. Rotate the Tuning control until 'Time' appears on the display. Press and release the Select button.
5. Rotate the Tuning control until 'Set Time/Date' appears on the display.
6. Press and release the Select button. The hour digits will flash on the display.
7. Rotate the Tuning control to set the desired hour.
8. Press and release the Select button. The minute digits will flash on the display.
9. Rotate the Tuning control to set the desired minute.
● If the radio has been set to use a 12 hour format, there will be an option here for setting AM or
PM for the clock time.
33
Time
<Set Time/Date
Set time
09:00
Set time
09:30
>
GB
10. Press and release the Select button. The day will flash on the display.
11. Rotate the Tuning control to change the day as needed.
12. Press and release the Select button. The month will flash on the display.
13. Rotate the Tuning control to set the current month.
14. Press and release the Select button. The year will flash on the display.
15. Rotate the Tuning control to set the current year.
16. Press and release the Select button to confirm the clock setting. The display will show 'Time
Saved' then exit the menu.
Set date
11- 1-2013
Set date
11- 1-2013
Set date
11- 1-2013
Time
Saved
34
Setting the clock format
The display used in standby mode and when the radio is in use can be set to 12 or 24 hour
format. The selected format is then also used when setting the alarms.
1. Press the Standby button to switch on your radio.
2. Press and release the Menu button until the Advanced menu shows on the display.
3. Rotate the Tuning control until 'System Setting' appears on the display. Press and release the
Select button.
4. Rotate the Tuning control until 'Time' appears on the display. Press and release the Select button.
5. Rotate the Tuning control until 'Time 12/24 hour' appears on the display. Press and release the
Select button.
6. Rotate the Tuning control to select either 12 or 24 hour format. The current hour format will be
marked with an asterisk. Press and release the Select button.
If the 12 hour clock format is chosen, the radio will then use the 12 hour clock for setting of
alarms, and will display a 12 hour clock with an AM or PM indicator when in standby mode.
35
DAB
<System Setting
>
System Setting
<Time
>
Set 12/24 hour
<Set 12 hour
>
Set 12/24 hour
<Set 24 hour
*
>
To return to auto clock set mode
GB
1. Press the Standby button to switch on your radio.
DAB
<System Setting
>
System Setting
<Time
>
5. Rotate the Tuning control until 'Auto update' appears on the display. Press and release the
Select button.
Time
<Auto update
>
6. Rotate the Tuning control to choose an update option from 'Update from Any', 'Update from
DAB', Update from FM' or 'No update' as required. The current update option will be marked
with an asterisk. Press and release the Select button to confirm your choice. The radio will exit
to the previous menu.
Auto update
<Update from Any
*
>
Auto update
<Update from DAB
>
2. Press and release the Menu button until the Advanced menu shows on the display.
3. Rotate the Tuning control until 'System Setting' appears on the display. Press and release the
Select button.
4. Rotate the Tuning control until 'Time' appears on the display. Press and release the Select button.
Note:
If you select 'Update from Any', 'Update from DAB', Update from FM' the current time received
will be displayed. If no signal is found you should either position the radio or its aerial so that a
signal can be received, or revert to manual clock mode.
36
Language function
Your radio can be configured to a different language.
1. Press the Standby button to switch on your radio.
2. Press the Menu button until the Advanced menu shows on the display.
3. Rotate the Tuning control until 'System Setting' appears on the display. Press and release the
Select button.
4. Rotate the Tuning control until 'Language' appears on the display.
5. Press and release the Select button to enter the language adjustment menu.
6. Rotate the Tuning control until your desired language appears on the display.
7. Press and release the Select button to confirm your choice. The display will change to the
chosen language. The chosen language will be marked with an asterisk.
Display backlight dimmer
In order to adapt the intensity of the display to suit the ambient room lighting, press the Dimmer
button on the top panel of your radio to select the dimmer brightness from Off, Low, Mid or High
settings.
37
DAB
<System Setting
>
System Setting
<Language
>
Language
<English
*
>
EQ function
GB
The sound on radio can be adjusted to suit your personal taste for the material that you are
listening to. The DDR-38 has six preset equalizer modes. Alternatively, you may set the treble
and bass levels to your own preferences.
1. Press the Standby button to switch on the radio.
2. Press and release the EQ button to enter the setup menu. “Equaliser” will appear on the display.
3. Rotate the Tuning control to cycle through the 6 preset modes below until the desired mode is
displayed. Press and release the Select button.
a. Normal - no tone modification is applied
b. Jazz
c. Rock
d. Classic
e. Pop
f . News
g. My EQ (Treble - tone setting may be adjusted/ Bass - tone setting may be adjusted)
<
Equaliser
Normal
>
38
Set up my EQ profile
If you find the preset equalizer functions not to your liking, you may set up a custom treble and
bass as following:
1. Follow step1-3 in the EQ function section in order to enter EQ menu.
2. Rotate the Tuning control until ‘My EQ’ is highlighted on the display. Press the Select button to
enter the adjustment mode.
3. Rotate the Tuning control to adjust the treble level (between -5 and +5). The sound will change
as you adjust the level. Press the Select button to confirm the setting. The display will then
revert to My EQ menu.
4. Rotate the Tuning control until ‘bass’ is highlighted on the display. Press the Select button to
enter the adjustment setting. Rotate the Tuning control until the desired level (between -5 and
+5) is displayed. The sound will change as you adjust the level. Press the Select button to
confirm the setting.
Note:
To quickly cancel the effect of My EQ profile, rotate the Tuning control until ‘Normal’ is highlighted
on the display and press the Select button. The treble and bass settings will be memorized for
the next time that you wish to use the My EQ.
39
<
Equaliser
My EQ...
>
<
My EQ...
Treble
>
<
Treble
+3
>
<
My EQ...
Bass
>
<
Bass
+3
>
Mute function
GB
Press the Mute button on the remote control of your radio, it will mute the output from the
loudspeakers.
1. Press the Mute button to mute the sound output. The speaker volume symbol on the display
will disappear.
2. Press the Mute button again or one of the Volume buttons to un-mute the sound output.
Software version
The software display cannot be altered and is just for your reference.
1. Press the Standby button to switch on your radio.
DAB
2. Press the Menu button until the Advanced menu shows on the display.
3. Rotate the Tuning control until 'System Setting' appears on the display. Press and release the
Select button.
4. Rotate the Tuning control until 'SW Version' appears on the display.
5. Press and release the Select button. The software version shows on the display.
6. Press and release the Menu button to exit the software version display.
<System Setting
>
System Setting
<SW Version
>
SW Version
dab-mmi-FS2052-000040
Software upgrades
Software updates for your radio may be available in the future.
As software updates become available software and information on how to update your radio can
be found at
http://sg.sangean.com.tw/first/first.asp
http://www.sangean.eu/first/first.asp
www.sangean.com.au.
For more information, please contact our Head Office by sending an email to info@sangean.com
1. Plug the USB into the USB socket in the rear of the unit.
2. Press and the Menu button to enter the Advanced menu of the current mode.
3. Rotate the Tuning control until 'System Setting' appears on the display. Press and release the
Select button.
4. Rotate the Tuning control until 'Software Upgrade' appears on the display. Press and release
the Select button.
5. Rotate the Tuning control until 'Yes' is highlighted on the display. If you do not wish to carry out
a software upgrade, highlight 'No' and then press the Select button. The display will revert back
to the previous display.
41
System reset
GB
If your radio fails to operate correctly, or some digits on the display are missing or incomplete
carry out the following procedure.
1. Press the Standby button to switch on your radio.
2. Press the Menu button until the Advanced menu shows on the display and then release the
button.
3. Rotate the Tuning control until 'System Setting' appears on the display. Press and release the
Select button.
4. Rotate the Tuning control until 'Factory Reset' appears on the display. Press and release the
Select button.
5. Rotate the Tuning control until 'Yes' is highlighted on the display. If you do not wish to carry out
a system reset, highlight 'No' and then press the Select button. The display will revert back to
the previous display.
DAB
<System Setting
>
System Setting
<Factory Reset
>
Factory Reset?
No
<Yes>
6. With 'Yes' highlighted, press and release the Select button. A full reset will be performed. The
station list and presets will be erased. Alarms will be cancelled and sleep timer settings will be
set to their default values. The display will show 'Welcome to Digital Radio' and the unit will
behave as when first switched on.
In case of malfunction due to electrostatic discharge, reset the product (reconnection of power
source may be required) to resume normal operation.
42
Headphone socket
A 3.5mm Headphone socket located on the rear of your radio is provided for use with
headphones. Inserting a plug automatically mutes the internal loudspeaker.
Please be aware that the sensitivity of headphones can vary widely. We therefore recommend
setting the volume to a low level before connecting headphones to the radio.
IMPORTANT:
Excessive sound pressure from earphones and headphones can cause hearing loss.
Line out socket (3.5mm Jack)
A 3.5mm Line Out socket located on the rear of your radio is provided for connecting the audio
signal to an external amplifier. Inserting an audio cable into this socket will not mute the internal
loudspeaker. Set the volume control on the radio to minimum if desired.
Auxiliary input socket
A 3.5mm Auxiliary input socket is provided on the rear of your radio to permit an audio signal to
be fed into the unit from an external audio device such as an iPod, MP3 or CD player.
1. Connect a stereo or mono audio source (for example, iPod, MP3 or CD player) to the Auxiliary
input socket (marked 'Aux In').
2. Press the Standby button to switch on your radio. The display will show 'Auxiliary Input'.
3. Adjust the Volume control on your iPod, MP3 or CD player to ensure an adequate signal and
then adjust the volume on the radio for comfortable listening.
43
Charging with USB socket
The USB jack can only provide power for the USB memory stick only
with 1A 5V maximum and most of iPhone models. However, it does not
support external Hard disk drive and all of mobile phones and electronic
device.
Important:
Do not connect this USB socket with your PC USB port, as it highly
possible may cause breakdown of the units.
GB
● Your radio should not be exposed to dripping or splashing and that
no objects filled with liquids, such as vases, shall be placed on the
radio.
● It is recommended to operate the product such that there is a
minimum distance (10cm recommended) to adjacent objects in order
to ensure good ventilation.
Cautions
● The ventilation of the product should not be restricted by covering
it or its ventilation openings with items such as newspapers,
tablecloths, curtains etc.
Do not allow this radio to be exposed to water, steam or sand. Do not
leave your radio where excessive heat could cause damage such as in
a parked car where the heat from the sun can build up even though the
outside temperature may not seem too high.
● No naked flame sources such as lighted candles should be placed
on the product.
● It is recommended to avoid using or storing the product at extremes
of temperature. Avoid leaving the unit in cars, on window sills, in
direct sunlight etc.
44
Specifications
Circuit features
Power Requirements
Mains AC 100- 240V ~ 50/60Hz (Adaptor)
Loudspeaker
2.25” 8 ohm x 2 full range
Output Power
5W+5W
Headphone socket
3.5mm dia
Aux in socket
3.5mm dia
Line out socket
3.5mm dia
Aerial system
FM telescopic aerial
DAB telescopic aerial
Frequency Coverage
DAB 174.928 - 239.200MHz
FM 87.50 - 108 MHz
The Company reserves the right to amend the specification without notice.
If at any time in the future you should need to dispose of this product please note that: Waste electrical products should not be disposed of with household waste. Please recycle where facilities exist. Check with your Local Authority or retailer for recycling advice.
(Waste Electrical and Electronic Equipment Directive)
45
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising