Axminster FT-1000 Specifications

Axminster FT-1000 Specifications
Dust Extraction & Wood Waste
Air Filters
Once the dust extractor is turned off, the cutting or sanding finished, off comes the mask and in most instances we think we have been very safety conscious. In fact, until a ray of sunlight passes through
the workshop window we are unaware that a very high level of dust is still present in the air, probably just as much as when the machine or dust producer was in full swing. In order to further improve your
workshop conditions, we offer a range of workshop air filters which may be left running quietly in the background, filtering out the very fine airborne dust particles. Using a two stage filter, the polyester
pre-filter removes the larger particles whilst the multi-pocket bag filter filters out the very much finer particles. Suitable for ceiling mounting, wall mounting or just ‘stand alone’, these air filters will greatly
improve the workshop environment. In order to specify the correct size filter or number of filters for a workshop, calculate the workshop volume and look to circulate the air some six times per hour.
N.B. Air filters are to be used in conjunction with dust extraction and do not dispel the need for efficient machine extraction.
2
Charcoal filter
Electrostatic pre-filter
Position anywhere in the workshop
Jet
AFS-500 Air Filtration System
£239.95
Ex.vat: £199.96
Code: 310483
108
Dust Extraction.indd 108
This is a medium to large workshop filter unit which has the
advantage that it can be positioned anywhere in the workshop,
either on a bench, a shelf or suspended from the ceiling. The
unit is easy to operate and has three speeds simply activated by
the push of a button or by using the convenient remote control.
It should be mounted away from ventilation and heating vents
and is only suitable for non-metallic dust particles. The unit can
be positioned either vertically or horizontally to best utilise the
space available. It is fitted with a pleated cloth main filter and an
electrostatically charged pre-filter. An optional charcoal filter is
available which can (a) neutralise odours and harmful organic
fumes and (b) refresh the air by removing smoke, dust, bacteria,
pollen and other harmful microscopic particles. Supplied with
main filter, electrostatically charged pre-filter and remote
control. For best results leave the AFS-500 running for an hour
to clean the air after your machines have been switched off, or
use the built in 2,4 or 8 hour timer options to run the filter after
you leave the workshop.
Replacement Filters
Inc.vat
Ex.vatCode
AFS-500/1000B Electrostatic Filter
£15.96
£13.30708731
AFS500 Main Filter
£31.96
£26.63310484
AFS-500/1000B Charcoal Filter
£28.96
£24.13708734
Free delivery on orders over £50 (UK mainland only) Orders UNDER £50 P&P £4.95
27/11/2014 16:02
Air Filters
Air Filter Mounting Kit
Ceiling mounting kit for the JET air filtration units consisting of
four lengths of flexible stainless steel wire with screw eyes and
bolt-up crimps.
Inc.vat
Ex.vatCode
Mounting Kit
£34.96 £29.13400398
A
A Inner main pleated filter
B Electrostatic filter
2
B
Perform CCAF
Spare Filters
Original quality replacement filters for the Perform CCAF Air
Filter. Both inner and outer filters available.
Inc.vat
Ex.vatCode
Replacement Outer Filter
£19.45 £16.21100102
Replacement Inner Filter
£22.96 £19.13100103
£309.96
Ex.vat: £258.30
Code: 310481
Jet AFS-1000B Air Filtration System
With a powerful Input 200W motor the AFS-1000 B is intended
for the bigger more commercial workshop; it needs a secure
mounting capable of holding a 40kg static load, at least 2 metres
off the ground. The air passes through the electrostatic pre-filter
into the main pleated filter, filtering 98% of all particles 5 microns
in size and 85% of all particles 1 micron in size. The remote
control unit has three settings for the motor speed and three
different time settings of 2 hours, 4 hours and 8 hours, which can
be used to clear the workshop after work has finished for the
day. An optional charcoal filter is available, which will neutralise
odours and harmful organic fumes or particles including pollen.
A handy ceiling mounting kit consisting of 4 lengths of flexible
stainless steel wire with screw eyes and bolt up crimps allows
the machine to be positioned out of the way. Supplied with
electrostatic pre-filter, main filter and 4 mounting eyes.
Axminster AFS2000 Spare Filters
Original quality spare filters for the Axminster AFS2000 Air Filter.
Outer and charcoal filters available.
Inc.vat
Ex.vatCode
Outer Filter
£21.46 £17.88708722
Inc.vat
Ex.vatCode
AFS-500/1000B Electrostatic Filter
£15.96
£13.30708731
AFS1000B Main Filter
£37.45
£31.21400395
AFS-500/1000B Charcoal Filter
£28.96
£24.13708734
Comparison Chart - Air Filters
AFS-500
Model
Trade
Rating
Power
Input 100W
Noise Level dB @ 1M
Speed 1, 56dB.
Speed 2, 58dB.
Speed 3, 60dB.
Filtration
2 Stage
Air Movement
360, 480, 600m³/hr
120m³
Room Volume
Particle Size
Inner-1 Micron, Outer-5 Microns
Overall L x W x H
400 x 610 x 300mm
15kg
Weight
AFS-1000 B
Trade
Input 200W
Speed 1, 62dB.
Speed 2, 66dB.
Speed 3, 68dB.
2 Stage
720, 900, 1,200m³/hr
300m³
Inner-1 Micron, Outer-5 Microns
768 x 610 x 305mm
25kg
Axminster CT510(D)
Jet AFS-1000B Main Filters
Spare original quality inner filters for the Axminster CT510, 510D
and Jet AFS-1000B air filtration units.
Inc.vat
Ex.vatCode
AFS1000B/CT510D Main Filter
£37.45 £31.21400395
Call free 0800 371822 Mobile friendly 03332 406406 Order online axminster.co.uk/extraction
Dust Extraction.indd 109
109
27/11/2014 16:03
Chip Extraction
These extractors are powered by centrifugal fans which draw a large volume of air through the inlet hose and discharge it through the fabric filter bag situated on the top of the machine. The waste falls
into the lower bag which will either be a fabric or plastic waste sacks, where applicable. Although these machines generate a large volume of airflow the pressure rise is low which makes them unsuitable
for operating with small diameter inlet hoses. A reduction below 3” diameter is not recommended. The mesh size of the filter bag has to be relatively coarse in order to allow the high volume of air to pass
through and thus the extractor is not suitable for filtering out the very fine dust produced by sanding machines. The cartridge filters available for most of the models will improve the level of filtration and
are nowadays fitted with deep pleats to avoid any loss of air flow. Generally suitable for collecting chippings and larger particle size sawdust from machines equipped with 3”, 4” or larger diameter outlets. For
the best results we recommend using an extractor with higher airflow than is required by the machine you are connecting it to.
Wood Waste Extraction
Not only does the introduction of an efficient dust or chip extraction system reduce this potential
health hazard, but it keeps the workshop cleaner and generally makes working with wood in a
confined space a much more enjoyable activity. The choice of the correct type of extractor for
any particular application can be a bit confusing, with apparently conflicting requirements for
collecting different types of waste from a wide variety of woodworking machinery. For more
information regarding the potential risks of wood dusts, please visit:
http://www.hse.gov.uk/woodworking/index.htm
and
http://www.hse.gov.uk/coshh/industry/woodworking.htm
850m³/hr air flow,
750W, 230V 1ph motor
As an aid to selecting a suitable extractor we have introduced the following performance rating
guide to give a quick indication of the type of waste that each extractor is designed to handle. If
you are still unsure of suitability please contact our Specialist Sales Dept on 03332 406406
Extraction Performance Ratings (guidance only)
1 - Chippings only
2 - Chippings and sawdust (with fine filter option fitted)
3 - Chippings, sawdust and sanding dust
4 - Chippings, sawdust, sanding dust and MDF dust
Bag filter
efficiency 30
micron
Quiet and efficient, will not
offend your neigbhours
Axminster Hobby Series
AWDE5002 Extractor
2
Inlet diameter
is 100mm
£154.96
Ex.vat: £129.13
Code: 501262
Base fitted with castors
and grab handle for
easy mobility
Can be used suspended from a wall,
brackets are provided
This extractor can be used in small home workshops for
common wood machining tasks where a higher airflow than
provided by a vacuum extractor is required. The quiet running
induction motor provides plenty of power to extract from many
small workshop machines. The inlet diameter is 100mm(4”), the
outlet into the bag is 100mm(4”) and the airflow is sufficient to
handle the majority of waste likely to be produced in the small
home workshop. A useful feature is that it can be used either
on the floor or suspended from a sturdy wall using the two
hanging brackets provided. A useful grab handle and castors
allow easy mobility. Hose not supplied. See extraction hose
selection for further details. Please note that this is a chippings
extractor and should not be expected to collect fine dust. As
with all the high volume low pressure airflow machines, the
inlet should not be restricted to below 75mm diameter and the
bag should be emptied regularly. Spare bag provided.
Performance Rating 1
Accessory
Inc.vat
Ex.vatCode
Quick Release 100mm Hose Clip (Pair)
£9.95
£8.29210323
Bag filter
efficiency 30
micron
Axminster Hobby Series
AWEDE2 Extractor
850m3/hr air flow,
0.75kW 230V 1ph
induction motor
£184.96
Can be upgraded
with a fine filter
cartridge
Ex.vat: £154.13
Code: 501263
Uses waste sack
size - 560 x 915mm
(340068)
100mm hose fits
directly to many
saws, planers,
bandsaws etc
Wheeled base and
grab handle for
ease of movement
110
Dust Extraction.indd 110
An attachment
provided to enable
easy floor cleaning
of wood chips
A chip and coarse dust extractor for extracting from hobby
series saws, planers, bandsaws and similar machines in a small
workshop. Equipped with two cloth bags, the top one acting
as the filter and the lower one for collecting the waste. Power
comes from a 750W induction motor equipped with a no-voltrelease switch and emergency stop button. If required, the cloth
collection bag can be replaced with plastic waste sacks, which
can be more convenient for storage of waste prior to disposal.
An unusual feature of this extractor is the floor sweeping
attachment which fits to the base of the machine, allowing
the extractor to be wheeled around the workshop, collecting
waste as it goes. There is a fine filter bag available for use when
collecting medium sized dust particles, or alternatively, an
optional fine dust cartridge filter can be fitted. (N.B.You must
use plastic waste sacks with the fine filter bag or cartridge
filter) The machine is supplied with approximately 600mm
length of inlet hose; additional lengths of 100mm hose are
available separately. This machine uses waste sack size - 560
x 915mm (340068).
Accessories
Inc.vat
Ex.vatCode
560 x 915mm Waste Sack Red (Pkt 10) £11.46
£9.55340068
Quick Fit Metal Strap to 1140mm(45”)
£7.45
£6.21800425
Replacement Filters
Inc.vat
Ex.vatCode
Fine Filter Bag
£10.45
£8.71500079
Cartridge Filter
£129.96 £108.30700344
axminster.co.uk/signup for our exclusive email offers
27/11/2014 16:03
Chip Extractors
Optional pleated
filter cartridge
available to
improve filtration
Bag filter
efficiency
30 micron
£274.96
Quiet and
powerful
1.5kW 1ph
230V motor
Ex.vat: £229.13
Code: 501264
High flow efficiency
impellor and
collector housing
Plastic
collection bag
as standard
2
Large capacity with
single 125mm and
twin 100mm inlets
2,000 m³ air flow @
100mm inlet
AWEDE2 Filter Cartridge
Base castors aid
movement around
the workshop
Axminster Hobby Series FM300BC Extractor
This extractor, with its 1.5kW motor, large capacity collection
bag and twin 100mm hose inlets, will handle most single
workshop machines. Use the single 125mm inlet or the twin
100mm adaptor for two smaller machines. The top cloth bag
acts as the filter whilst the lower plastic bag collects the coarse
dust and chippings. Plastic bags allow a number of bags to be
filled and stored ready for bulk disposal. The extractor’s filtration
system can be upgraded with the addition of the cartridge filter.
The solid connection tube between the impellor housing and
Air filter cartridge for the AWEDE2 Extractor. Upgrades the
performance of this extractor, able to handle fine saw dusts
as well as chippings. Simply slots on with a stiff rubber seal.
You must use plastic waste sacks with this filter. Partical size 1
micron. Internal mounting size is 360mm diameter.
Inc.vat
Ex.vatCode
collector creates an efficient air flow system. Castors on the base
Cartridge Filter
£129.96 £108.30700344
allow for easy mobility around the workshop. This is a good,
solid, simple extractor. Lengths of suitable inlet hose are listed
under Dust Extraction Accessories. N.B. This machine uses
waste sack size 785 x 1,200mm (501187).
Inc.vat
Ex.vatCode
785 x 1,200mm Waste Sack Yellow (Pkt 10)£17.46
£14.55501187
Quick Fit Metal Strap to 1450mm(57”)
£7.45
£6.21800426
Cartridge Filter for FM300BC
£159.96 £133.30700345
Comparison Chart - Hobby Chip Extractors
AWDE5002
AWEDE2
FM300B
Model
Hobby
Hobby
Hobby
Rating
Power
750W (230V, 1ph)
750W (230V, 1ph)
1.5kW (230V, 1ph)
Air Flow
850m³/hr
840m³/hr @ 100mm
2,000m³/hr @100mm inlet
2,500m³/hr @125mm inlet
70dB(A)
73dB(A)
77dB(A)
Noise Level
Filtration
30 micron
30 micron
30 micron
Particle Size
30 micron
30 micron
30 micron
100mm
100mm
1 x 125mm or 2 x 100mm
Hose Diameter
Bag Capacity
37 litres
57 litres
150 litres
Overall L x W x H
380 x 1,100 x 410mm
790 x 370 x 1,530mm
920 x 560 x 1,960mm
22kg
24.5kg
47kg
Weight
AWEDE/FM300BC/
FM300SA Filter Cartridge
Air filter cartridge for the AWEDE, FM300BC and FM300SA chip
extractors. Upgrade the performance of these extractors, able
to handle fine saw dusts as well as chippings. Simply slots on
with a stiff rubber seal. Partical size 1 micron. Internal mounting
size is 480mm diameter. N.B. 2 Filter Cartridges required for
FM300SA
Inc.vat
Ex.vatCode
Cartridge Filter for FM300BC
£159.96 £133.30700345
Call free 0800 371822 Mobile friendly 03332 406406 Order online axminster.co.uk/extraction
Dust Extraction.indd 111
111
27/11/2014 16:03
Chip Extraction
1 micron cartridge
filter with high
airflow, internal
paddle for cleaning
1 micron cartridge
filter with high
airflow, internal
paddle for cleaning
Common sized
100mm inlet, suits
many machines
Common sized
100mm inlet, suits
many machines
Rugged build for
the trade workshop
environment
Rugged build for
the trade workshop
environment
2
Generous airflow
from the efficient
alloy impeller
Wheeled base
and handle for
easy mobility
Generous airflow
from the efficient
alloy impeller
Wheeled base
and handle for
easy mobility
Plastic waste sack
secured by quick
fit metal strap
Plastic waste sack
secured by quick
fit metal strap
Axminster Trade Series CT-90H Extractor
Axminster Trade Series CT-90HB Extractor
A thoroughly modern design of dust extractor with a cartridge filter as standard. The excellent
performance comes from careful matching of the motor, impeller and housing, resulting in a
quietly efficient machine able to extract chips and medium sized dust from almost all small and
medium sized machinery. An alloy impeller is fitted to reduce the risk of sparks and the cartridge
filter has a rating of 1 micron. A large capacity plastic waste sack and quick release straps are
included. A comfortable tubular handle, steel rear wheels and front castor wheels are provided for
easy mobility. The cartridge filter increases the potential use of this machine to include sanders
as well as the normal range of saws, planers etc. Easy to keep clean with the top mounted crank
handle, the extra surface area means that the overall airflow is not significantly reduced. Overall, a
fine, modern extractor for any trade workshop, or a quality machine for your workshop at home.
Hose not supplied.
A thoroughly modern design of mobile dust extractor with a cartridge filter included as standard.
The excellent performance comes from careful matching of the motor, impeller and housing,
resulting in a quietly efficient machine able to extract chips and medium sized dust from almost
all Trade specification machinery. An alloy impeller is fitted to reduce the risk of sparks and the
extra large cartridge filter has a rating of 1 micron. A large capacity plastic waste sack and quick
release straps are included. A comfortable tubular handle, steel rear wheels and front castor wheels
are provided for easy mobility. The cartridge filter increases the potential use of this machine to
include sanders as well as the normal range of saws, planers etc. Easy to keep clean with the top
mounted crank handle, the extra surface area means that the overall airflow is hardly reduced.
Overall, a fine, modern extractor for any trade workshop. Hose not supplied.
Specification - CT-90H
ModelCT-90H
RatingTrade
0.75kW 230V 1ph
Power
850 m³/h
Air Flow
Noise Level65dB
1 micron
Particle Size
Hose Diameter100mm
60 litre
Bag Capacity
720 x 660 x 1460mm
Overall L x W x H
Weight32kg
Specification - CT-90HB
ModelCT-90HB
RatingTrade
1.5kW 230V 1ph
Power
2,250 m³/hr at 175mm, 1,200 m³/hr at 100mm
Air Flow
Noise Level70dB
1 micron
Particle Size
1 x 175mm, 2 x 100mm
Hose Diameter
170 litre
Bag Capacity
1000 x 800 x 1,900mm
Overall L x W x H
Weight67kg
£369.96
Ex.vat: £308.30
Code: 508334
112
Dust Extraction.indd 112
£574.96
Ex.vat: £479.13
Code: 508336
Free delivery on orders over £50 (UK mainland only) Orders UNDER £50 P&P £4.95
27/11/2014 16:03
Chip Extraction
High efficiency cyclone,
99% separation of dust
and air before passing
through the filter
Manual filter
cleaning system, easy
to maintain air flow
Nice compact design,
perfect for a ducted system
1 micron filter
cartridge,
optional 0.3
micron HEPA
filter available
Manual filter
cleaning
system, easy
to maintain
air flow
Choice of
1x180mm or 2x
100mm inlets
Choice of
1x150mm or 2x
100mm inlets
High efficiency cyclone,
99% separation of dust
and air before the filter
1 micron filter
cartridge,
optional 0.3
micron HEPA
filter available
2
Nice compact design,
easy to move around
the workshop
Large waste bin with
internal waste sack
for easy emptying
Large waste bin with
internal waste sack
for easy emptying
£749.95
£1,099.96
Ex.vat: £624.96
Code: 505087
Ex.vat: £916.63
Code: 505088
Easy to empty steel drum
with castors for mobility
Axminster Trade Series
T-2000CK 1hp Cyclone Extractor
Axminster Trade Series
T-2000CK 2hp Cyclone Extractor
Easy to empty steel drum
with castors for mobility
This is a small, highly portable cyclone extractor, aimed at the smaller workshop with many
different types of machinery in use. Having a high efficiency separation system means that the air
passing through the filter is 99% clean of waste, maintaining a high airflow for top performance.
The filter has a 1 micron filtration performance and is fitted with a simple manual cleaning system.
A manometer gauge gives an easy visual performance reference. The large waste bin is 105 litres
and is easy to remove and empty. Fitted with sturdy castors, this extractor is quite mobile so is easy
to move from machine to machine. However, with a 150mm inlet it also lends itself to be fitted to a
permanent ducting system. Able to run from a standard 13A plug, it is an attractive proposition for
a small trade workshop or a keen amateur in a home workshop.
This larger “Trade” rated extractor is also compact in size and is able to extract from larger, higher
waste volume producing machines. Sharing the same high efficiency air flow system ensures
high, consistent performance. Over 99% of waste is separated from the air stream before the air
is passed through the 1 micron filter; a simple manual filter cleaning system keeps the filter clean.
There is a manometer fitted to give a quick, visual indication of the filter performance. Waste
container 155 litres is easily detached from the machine and has castors to allow easy mobility. The
machine is fitted with wheels for mobility, but we would suggest the best way to get most benefit
from this machine is to connect it to a permanent ducting system. The 180mm inlet would allow
a multiple ported system to be used. Quiet and unobtrusive in use, this would be a good choice in
many workshops. (N.B. 16A supply required)
Comparison Chart - Cyclone Extractors
HEPA Filter for T-2000CK Cyclones
T-2000CK-HR
T-2000CK
Model
Trade
Trade
Rating
1.5kW (230V, 1ph)
0.75 kW (230V, 1ph)
Power
2,300m³/hr
1,100m³/hr
Air
Flow
84dB @ 3m
80 dB @ 3m
Noise
Level
7.4m²
3.8m²
Filter
Area
1 micron
1 micron
Filtration
1 micron
1 micron
Particle
Size
150mm x 1, 100mm x 2
180mm x 1, 100mm x 2
Hose
Diameter
1,300 x 1,100 x 1,560mm
1,250 x 1,000 x 1,800mm
Overall
L x W x H
83kg
71kg
Weight
These optional HEPA cartridge filter’s for the T-2000CK 1hp and
2hp Cyclone Extractor’s gives a 0.3 micron filtering performance.
These filter’s are best suited for use when these machine’s are
mainly being used for extracting from sanders or other fine dust
producing machines. Some extra attention paid to keeping the
filter clean will pay dividends for the performance of these filter’s.
Inc.vat
Ex.vatCode
HEPA Filter for T-2000CK 1hp Cyclone £179.95 £149.96505089
HEPA Filter for T-2000CK 2hp Cyclone £259.96 £216.63505090
Call free 0800 371822 Mobile friendly 03332 406406 Order online axminster.co.uk/extraction
Dust Extraction.indd 113
113
27/11/2014 16:03
Chip Extraction
£299.95
Ex.vat: £249.96
Code: 700231
£714.96
2
Ex.vat: £595.80
Code: 700389
Jet DC1900A Extractor
Jet DC-950A Extractor
Fitted with an industrial quality motor and specially designed impellor and housing for high
extraction efficiency and quiet, vibration free running. Quick install collection bags means no
straps are required. Four castors allow easy mobility. The 100mm inlet allows connections to most
workshop machines, this extractor will easily cope with a 12” saw or 10 x 6” planer/thicknesser.
Rugged design, withstands everyday use. Perfect for a small workshop, and offers a much better
performance than lower cost machines. Supplied with a pack of five collection bags and a 30
micron filter bag. An optional Fine Filter Cartridge (700232) will filter out fine saw and sanding
machine dusts. Supplied without a hose.
N.B. This machine uses waste sack size - 560 x 915mm (340068).
A high quality chip/coarse dust extractor, for connection to multiple machines or, ideally, to a
ducted system. With an airflow of 2,400 m3/hr it will easily handle 2-3 small workshop machines or
1 large multiple outlet machine. Robustly built, quiet running and efficient in design this machine
will suit the majority of requirements found in a typical small carpenter/joinery workshop. Fitted
with a high efficiency steel fan and the unique “Vortex” cone design which maintains a high
collection performance by preventing premature clogging of the filter. This works by separating
the waste from the airflow, diverting the waste into the collecting bags. You can also upgrade
the filtration performance by the addition of two Fine Filter Cartidge’s which will have a very
noticeable effect when the extractor is used on sanding machines. The filter’s performance is
maintained by the use of the internal paddle blade, operated by a handle on the top of the filter
housing. Powered by a 2.2 kW 415V 3ph motor, this is a compact and very versatile extractor.
Supplied with a pack of five collection bags and a 30 micron filter bag. Supplied without a hose.
N.B. This machine uses waste sack size - 785 x 940mm (410241).
Accessories
Inc.vat
Ex.vatCode
560 x 915mm Waste Sack Red (Pkt 10) £11.46
£9.55340068
Fine Filter
Cartridge for
Jet DC-950A
Accessories
Inc.vat
Ex.vatCode
785 x 940mm Waste Sack Orange (Pkt 10) £13.96
£11.63410241
Comparison Chart - Jet Chip Extractors
DC-950A
DC1900A
DC-1100A
Model
Trade
Trade
Trade
Rating
Power
750W (Max Input 1,250W)
2.2kW,
(Max Input 4.25kW),
1.1kW (Max Input 1.9kW)
Fine Filter Cartridge for the Jet DC-950A
230V 1ph
415V, 3ph
230V 1ph
Extractor. Upgrades the machine to
950m³/hr
2,900m³/hr @ 200mm
1,620 m³/hr @ 150mm
Air Flow
handle fine saw and sanding machine
1,100 m³/hr @ 100mm
dusts. Simply clamps on with four hand
70dB(A)
80dB(A)
80dB(A)
Noise Level
knobs. Easily cleaned with a crank
Particle Size
30 micron
30 micron
30 micron
handle. Particle size 1 micron. Internal
100mm
3 x 100mm or 1 x 200mm
150mm, 2 x 100mm
Hose Diameter
mounting size is 360mm diameter.
Bag Capacity
58 litres
400 litres
200 litres
Inc.vat
Ex.vatCode
Overall L x W x H
670 x 355 x 1,440mm
1,500 x 760 x 2,400mm
940 x 510 x 1,830mm
Fine Filter for DC-950A
£279.96 £233.30700232
38kg
95kg
71kg
Weight
114
Dust Extraction.indd 114
axminster.co.uk/signup for our exclusive email offers
27/11/2014 16:03
Chip Extraction
Without the Vortex Cone
– filter gets clogged
reducing performance
and requiring frequent
maintenance.
£364.96
Ex.vat: £304.13
Code: 210045
With the Vortex Cone
– filter stays cleaner
preserving performance
and requiring little
maintenance.
Particle separation technology
that prevents up to 98% of
particles from entering the upper
bag or canister.
2
Performance
Only fine particles move to the filter chamber making manual
cleaning easier and decreasing health concerns.
Prevention
Prevents the central airflow from floating chips into the
filter chamber decreasing rapid performance drop due to
premature clogging.
Efficiency
Chips are better contained for increased packing density
requiring fewer collection bag changes.
Jet DC1100A Extractor
This ruggedly made extractor is designed for extended workshop use. Offering industrial quality
construction and exceptional wood chip and sawdust extraction, it is large enough for a 300mm
planer or many other workshop machines. Fitted with a high efficiency steel fan and the unique
“Vortex” cone design which maintains a high collection performance by preventing premature
clogging of the filter. This works by separating the waste from the airflow, diverting the waste
into the collecting bag. The base is fitted with castors for total mobility around the workshop. The
150mm inlet is fitted with a twin branch 100mm adaptor, allowing connection to either one or two
machines. This machine is also available already upgraded to handle finer dusts with the addition of
a 1 micron Fine Filter Cartridge (717141). This makes this already fine machine even more vesatile.
Supplied with a pack of five collection bags and a 30 micron filter bag. Supplied without a hose.
Please note this machine uses waste sack size - 785 x 940mm (410241).
N.B. May require 16A supply
Accessories
Inc.vat
Ex.vatCode
785 x 940mm Waste Sack Orange (Pkt 10) £13.96
£11.63410241
Fine Filter Cartridge for
Jet DC1100A or DC1900A
Jet DC1100A Extractor
and filter package deal
£599.95
Ex.vat: £499.96
Code: 717141
Fine filter cartridge for DC1100 and DC1900A. 1 micron fitration,
when fitted to either machine it upgrades the performance to
be able to handle fine dusts from saws and sanding machines.
Has 6 times the surface area of a standard filter bag. This
ensures no loss of air flow and maintains performance. Internal
mounting size is 515mm diameter. Note, two units are required
for the DC1900A model.
Inc.vat
Ex.vatCode
Fine Filter £274.96 £229.13700390
Call free 0800 371822 Mobile friendly 03332 406406 Order online axminster.co.uk/extraction
Dust Extraction.indd 115
115
27/11/2014 16:03
Industrial Extractors
Automatic
filter cleaning
for consistent
performance
£1,859.95
Filter cartridge
captures 99% of
dust from 0.2-2
microns in size
Ex.vat: £1,549.96
Code: 210642
Steel impellor
in close housing
gives exceptional
perfomance
£2,219.95
Ex.vat: £1,849.96
Code: 210643
Automatic
filter cleaning
for consistent
performance
Steel impellor
in close housing
gives exceptional
perfromance
2
Large 277 litre
chipping drum
Filter cartridge captures
99% of dust from 0.2-2
microns in size
Large 123 litre
chipping drum
Easy mobility thanks
to large castor wheels
Easy mobility thanks
to large castor wheels
Axminster Industrial Series
UB-2200VECK Cyclone Extractor
This is a mobile cyclone dust extractor suitable for small to medium sized trade workshops. Able
to handle most types of wood waste except for the very finest of dusts. With a 200mm inlet this
is very suitable for a ducted workshop system, or if required, you could connect to two machines
using the included 2 x 100mm adaptor. Nice and quiet in operation and features automatic filter
cleaning for consistent airflow. A
manometer gives a quick, visual
indication of performance. The
wheeled waste bin makes the
task of waste disposal easier.
This machine is a great all round
extractor, able to cope with
all but the largest machines.
Supplied with 0.2 micron
polyester cartridge filter, plastic
collection bag and steel impeller.
N.B. 16A supply required.
Axminster Industrial Series
UB-3300VECK Cyclone
Extractor
This is a mobile cyclone dust extractor suitable
for the medium to large sized trade workshops.
Able to handle most types of wood waste except
for the very finest of dusts. With a 200mm inlet
this is very suitable for a ducted workshop
system, or if required, you could connect to
three machines using the included 3 x 100mm
adaptor. Nice and quiet in operation and features
automatic filter cleaning for consistant airflow.
A manometer gives a quick, visual indication
of performance. The wheeled waste bin makes
the task of waste disposal easier. This machine
is a great all round extractor, able to cope with
even large machines. Supplied with 1 micron
polyester cartridge filter, plastic collection bag
and steel impellor. N.B. 16A supply required.
Comparison Chart - Industrial Extractors
UB-2200VECK
UB-3300VECK
Model
Industrial
Industrial
Rating
1.5kW (230V 1ph)
2.25kW (230V 1ph)
Power
2,700m³/hr
3,700m³/hr
Air Flow
74dB(A) @ 3m
78dB(A) @ 3m
Noise
Level
3.7m²
6.5m²
Filter
Area
1 micron
1 micron
Particle
Size
Hose Diameter
100mm x 2 & 200mm x1
100mm x 3 & 200mm x1
1,000 x 670 x 1,700mm
1,200 x 670 x 2,200mm
Overall
L x W x H
131kg
179kg
Weight
116
Dust Extraction.indd 116
Waste Sacks for UB-2200
and UB-3300 Cyclone
Extractors
Replacement waste sacks for the Axminster UB-2200
and UB-3300 Cyclone Extractors. Sold singly.
Inc.vat
Ex.vatCode
UB-2200 Drum Waste Sack
£3.76
£3.13950116
UB-2200/3300 Waste Sack for Filter
£2.26
£1.88950117
UB-3300 Drum Waste Sack
£5.26
£4.38950118
Free delivery on orders over £50 (UK mainland only) Orders UNDER £50 P&P £4.95
27/11/2014 16:04
Vacuum Extractors
Head secured with
quick release strap to
allow easy emptying
1,100W 230V 1ph
brush motor
35L drum capacity, 1 micron
cartidge filter
fitted
100mm x
1.5m flexible hose
supplied
Noise level 85dB(A)
Optional hose and adaptor
for power tool use available
(718910)
Axminster Hobby Series
RDC100H Vacuum Extractor
Air flow 180m³/hr,
Suction Pa 25,000
£119.95
Ex.vat: £99.96
Code: 501269
The RDC100H is a great, entry level workshop vacuum extractor,
just right for the hobby woodworker working in a small home
workshop. This machine will cope with waste shavings from most
bench top machines and the smaller floor standing machines,
especially bandsaws, circular saws, bench top surface planers
and handheld power tools (with the accessory power tool hose
kit, 718910). The power head has a grab carrying handle and is
fixed to the drum with a metal quick release strap. Fitted with
a two stage filter comprising a cartridge filter and outer paper
filter this will provide filtration of 1 micron. This machine is a
great alternative to your household vacuum cleaner!
Numatic 2.9m Hose, Stepped
Reducer & Reducer End Cap PACKAGE DEAL
Package deal comprises the Numatic 2.9m Hose, Numatic
Stepped Hose Reducer and the Numatic Reducer End Cap.
Numatic 2.9m Hose
• 2.9m hose for use when extracting from power tools when
fitted with the 610325 stepped adaptor
• Fits all Numatic/Axminster vacuum extractors fitted with a
51mm threaded cuff
Numatic Stepped Hose Reducer
• Connects extraction hoses to a variety of power tools
• Can be trimmed to suit a range of outlet diameters
Numatic Reducer End Cap
• Numatic reducer end cap 100mm - 51mm
• Allows the fitment of the 718085 pwer tool hose to a 100mm
hose or extraction duct
This kit allows almost all small bench top machines or hand held
power tools to be connected to the DC1100A Extractor. With a
2.9m hose and stepped rubber adaptor for easy connection.
2
Accessories
Inc.vat
Ex.vatCode
Inc.vat
Ex.vatCode
RDC100H Filter Cartridge
£7.96
£6.63210092
2.9m Hose, Stepped Reducer
RDC100H Filter Bags Pkt 5
£3.46
£2.88210091
& Reducer End Cap
£45.96 £38.30718910
Numatic NV750 Workshop
Vacuum Extractor
£279.96
Ex.vat: £233.30
Code: 702413
Specifications
RDC100H
Model
Hobby
Rating
Power
1,100W (230V)
180m³/hr
Air Flow
85dB(A)
Noise Level
Filtration
Particle Size
1 micron
100mm
Hose Diameter
Overall L x W x H
400 x 400 x 700mm
10kg
Weight
NV750
Trade
1,200W (230V)
150m³/hr
70dB
Permatrex filter + HEPAFLO bags
0.5 micron @ 99.97% capture rate
51mm
450mm diameter x 650mm height
11.2kg
Perfect for almost any workshop and offering unrivalled
performance, the NV 750 “L” class workshop vacuum extractor
is quiet, efficient and built to last. Specifically aimed at users
of small, bench top machines and power tools, this extractor
is light in weight and easily stored under the workbench.
The head assembly incorporates a 1,200W “TwinFlo” vacuum
motor providing ample power for all tasks and has a 10 metre
cord set. The extractor is fitted with a “Permatex” filter giving
filtration down to 0.5 micron @ 99.95%, with the option of
fitting a “HepaFlo” disposable filter bag if required for safe
waste disposal - a must when machining MDF. As standard,
this machine meets the L Class filtration standards but can be
upgraded to M Class filtration standards with the addition of the
optional HEPA module (210658). There is a blower socket for
the exhaust air which can be directed away from the work area
if required. The drum assembly incorporates a 51mm cyclonic
inlet connector for large dust/chips, and a 51mm front entry
for use with HepaFlo bags making this the perfect solution
to almost all small machinery or power tool applications. The
accessory kit includes a 2.5 metre 51mm flexible extraction
hose with a rubber expanding cuff for linking to most small
workshop machines with up to 58mm dust ports. A 51mm
stainless steel “gulper” crevice tool is provided for general
workshop cleaning. The wide range of accessories available
enable this extractor to be tailored to suit your needs.
A 2.9 metre 32mm hose and rubber step down adaptor for
connecting to hand operated power tools or small, bench top
machines are popular accessories, as are the floor cleaning kit
and mobility chassis. This machine is the ideal solution for
those requiring something portable and also to handle a large
range of extraction tasks. It is robustly built in heavy gauge
epoxy painted steel, and it’s designed and made in England!
Accessories
Inc.vat
Ex.vatCode
HEPA Module
£249.96 £208.30210657
Extraction Hose 2.9m & Adaptor
£32.95
£27.46718085
2.9m 32mm hose
£21.96
£18.30210551
Hepaflo Filter Bags NVM-4BH (Pkt 10) £19.96
£16.63211015
Floor Cleaning Kit
£89.95
£74.96600071
Clip-on Mobility Chassis
£89.95
£74.96210656
Call free 0800 371822 Mobile friendly 03332 406406 Order online axminster.co.uk/extraction
Dust Extraction.indd 117
117
27/11/2014 16:04
Vacuum Extractors
Fitted with a red “Filtrex” primary filter
and a secondary “Permatex” filter
giving filtration down to 0.5 microns @
99.95% (L Class)
All steel epoxy
coated power head
All steel epoxy
coated power head
2 x 1,200W “TwinFlo”
vacuum motors, gives
ample performance
2 x 1,200W
“TwinFlo” low
noise vacuum
motors
Can be upgraded to M
Class filtration using a
HEPA module (210657)
Cyclonic inlet,
prevents filter
blinding
WMD750 Mk2
4m high quality
smooth bore hose
with rubber end
cuffs and clips
£549.96
Fitted with a red
“Filtrex” primary
filter and a secondary
“Permatex” filter
giving filtration down
to 0.5 microns @
99.95% (L Class)
Ex.vat: £458.30
Code: 501299
Cyclonic inlet,
prevents filter
blinding
WMD750 Mk2 “M” Class
35L capacity
epoxy coated
all steel drum
2
£759.96
Ex.vat: £633.30
Code: 501300
£399.96
4m high quality smooth
bore hose with rubber
end cuffs and clips
Ex.vat: £333.30
Code: 702412
Supplied with 4m
x 100mm flexible
extraction hose, 2.9m
x 32mm hose and step
down adaptor for power
tool use
Numatic NVD750 Workshop Vacuum Extractor
Tough, easy to
empty waste
sack, holds at
least 80 litres
of waste
Accessories include wall mounting
bracket and 4m x 100mm extraction
hose
Can be upgraded to M Class
filtration using a HEPA
module (210657)
Numatic
WMD750 Mk2
Workshop Vacuum
Extractor
Supplied with 4m x 100mm
flexible extraction hose, 2.9m
x 32mm hose and step down
adaptor for power tool use
The WMD 750 wall mounted vacuum extractor is intended for permanent siting on a load bearing
wall (wall bracket included). The extractor incorporates many features including a visual flow
indicator and easy disassembly for cleaning and maintenance. Included is a heavy duty woven
waste sack, attached with a quick release strap, making waste disposal, quick, easy and clean. The
head assembly incorporates two “TwinFlo” 1,200W vacuum motors providing ample power for
all but the most demanding of tasks. The extractor is fitted with a “Filtrex” primary filter and a
“Permatrex” secondary filter as standard, giving L Class filtration of 0.5 micron @ 99.95%. The “Filtrex”
filter acts as an impact absorber for the main filter as well as providing primary filtration. The drum
assembly incorporates a 100-32mm cyclonic inlet connector, making this the perfect solution
to many workshop applications. An extra layer of filtration can be provided by using an open
HepaFlo bag supplied with the machine. Fitted to the front 51mm inlet, it is best used for power
tool extraction. The accessory kit supplied with this machine includes a 4 metre 100mm extraction
hose with soft rubber cuffs for linking to a ducted system or for direct connection to most machines.
A 32mm hose and stepped rubber reducer for extracting from handheld power tools are part of
the standard equipment supplied. This machine is ideal for those where workshop space is tight,
or where sanders are a prime machine in use. The whole machine is very ruggedly constructed in
epoxy painted steel and has a 2 year warranty. Another class leading British made product. N.B. For
those requiring an “M” Class filtration machine, we now offer this option, 501300.
As standard, this machine meets the L Class filtration standards but can be upgraded to M Class
filtration standards with the addition of the optional HEPA module (210657). When it comes to
workshop applications coupled with unrivalled performance, the NVD 750 workshop vacuum
extractor is in a class of its own. Many operational features are included within the package which
will enable the user to link the extractor to a machine or hand operated power tool as required.
The head assembly incorporates two 1,200W “TwinFlo” vacuum motors providing ample power
for all but the most demanding of tasks. A visual flow indicator is also fitted for monitoring
performance. The extractor is fitted with a red “Filtrex” primary filter and a secondary “Permatex”
filter as standard, with the option of fitting a “HepaFlo” disposable filter bag if required, a must
when machining MDF. The “Filtrex” filter also protects the filter system from impact damage from
fast moving larger chips. There is an exhaust blower socket to enable the exhaust air to be ducted
away from the workshop if required. The 10 metre cable set provides all round the workshop use
from one power point. The drum assembly incorporates a 100mm cyclonic inlet connector, this
is the best method of connection for most tasks. A 100-51mm reducer is provided to enable the
2.9 metre 32mm power tool hose to be fitted. The 51mm front entry is used when you need to
use the Hepa Flo collection bags, perfect for the safe disposal fine or MDF dusts. The accessory
kit provided with this extractor includes a 4 metre x 100mm diameter flexible extraction hose for
Comparison Chart - Trade Vacuum Extractors
linking to most small workshop machines, and a 2.9 metre 32mm hose and step down adaptor
for connecting to hand operated power tools or small, bench top machines. The wide range of NVD750
WMD750 Mk2
Model
accessories available enable this machine to be tailored to your own specific use, including a
Trade
Trade
Rating
mobility chassis and a floor cleaning kit. This machine is the best solution for those requiring
2 x 1,200W (230V)
2 x 1,200W (230V, 1ph)
Power
something portable and also to handle a large range of extraction tasks. It is ruggedly made in 300m³/hr
300m³/hr
Air Flow
epoxy painted steel, and is designed and made in England!
79dB
79dB
Noise Level
Permatrex filter
+ HEPAFLO bag
Permatrex filter + HEPAFLO bag
Filtration
Accessories
0.5
micron @ 99.97%
0.5 micron @ 99.97% capture rate
Inc.vat
Ex.vatCode
Particle Size
100mm + 51mm
100mm + 32mm
Hepaflo Filter Bags NVM-4BH (Pkt 10) £19.96
£16.63211015
Hose Diameter
70 litres
HEPA Module
£249.96 £208.30210657Bag Capacity
x 650mm height
500 x 400 x 1,110mm
Floor Cleaning Kit
£89.95
£74.96600071
Overall L x W x H 450mm diameter
26kg
Clip-on Mobility Chassis
£89.95
£74.9621065612.8kg
Weight
118
Dust Extraction.indd 118
axminster.co.uk/signup for our exclusive email offers
27/11/2014 16:04
Downdraft Tables
£169.96
Clear
Lightweight PVC
Extraction Hose
Ex.vat: £141.63
Code: 501266
Rubber grommets for
workpiece protection
100mm outlet port to connect
to your dust extractor
Internal baffles to provide equal air
flow all over the table surface
Axminster Hobby Series
DT-700U Downdraft Table
The DT-700U is very useful when hand sanding. Of all steel
construction, with a generous 903 x 473mm table size and
protective rubber grommets, quite large items can be placed
onto this downdraft table. Internal baffles ensure equal air
movement over the entire table surface. A high volume
extractor of 1000 m³/hr minimum is recommended rather than
a vacuum type machine. Usefully, it can be stored on one end
when not in use.
Axminster Downdraft Table Kit
This kit allows you to create your own downdraft table. You
just need to construct a box from 12mm ply or MDF (plans
included), add the table plates and dust port to create a small,
benchtop table. The finished size will be approximately 620
x 420 x 160mm. You could, of course, build larger tables by
purchasing multiple kits. A full set of 64 grommets and four
work supports are included with each kit. A suitable extractor is
required, either a 1,000m³ typical bag type with a fine filter or a
1,200W vacuum extractor as a minimum.
• Lightweight, double ply PVC wall, encapsulating a spring steel
wire helix
• Extremely flexible, can be used where tight curves are required
• Blockages can be easily seen, enhancing the systems
performance
• Clockwise spiral
Inc.vat
Ex.vatCode
Clear Hose 51mm x 1M
£10.96 £9.13505001
Clear Hose 63mm x 1M
£14.95 £12.46505002
Clear Hose 63mm x 2.5M
£30.96 £25.80505003
Clear Hose 76mm x 1M
£16.96 £14.13505004
Clear Hose 76mm x 2.5m
£33.96 £28.30200774
Clear Hose 102mm x 1m
£19.45 £16.21200776
Clear Hose 102mm x 2.5m
£47.95 £39.96200777
Clear Hose 102mm x 5m
£79.96 £66.63200778
Clear Hose 102mm x 10M
£149.95 £124.96505005
Clear Medium
Weight PVC
Extraction Hose
• Medium weight, double
ply clear PVC hose
• F ully encapsulated PVC coated
close pitch spring steel wire helix
• Moderately flexible, it will accommodate quite tight curves
• The inner wall is markedly smooth, aiding the flow of waste
• Also being clear any blockages are easily spotted.
Inc.vat
Ex.vatCode
• Temperature range 0°C to +70°C, withstands quite abrasive
Downdraft Table Kit
£44.95 £37.46508319
materials
• Clockwise spiral
FT-1000
£819.96
Ex.vat: £683.30
Code: 501227
2
Inc.vat
Ex.vatCode
Clear Reinforced PVC Hose 102mm x 1m £20.95 £17.46505006
Clear Reinforced PVC Hose 102mm x 2.5m £47.95 £39.96505007
Clear Reinforced PVC Hose 102mm x 5m £93.96 £78.30505008
Clear Reinforced PVC Hose 102mm x 10m £169.96 £141.63505009
Clear Reinforced PVC Hose 127mm x 1m £26.95 £22.46505010
Clear Reinforced PVC Hose 127mm x 2.5m £64.96 £54.13505011
Clear Reinforced PVC Hose 152mm x 2.5m £69.96 £58.30505012
Clear Heavy Duty
PU Extraction Hose
FT-1600
£1,399.96
Ex.vat: £1,166.63
Code: 501228
Axminster Trade Series FT-1000 & FT-1600 Downdraft Tables
Downdraft tables are an excellent method of capturing airborne
dust created when hand sanding items of furniture. Because the
air flow is downwards the dust is naturally drawn towards the
table surface which has a series of hollow rubber grommets all
it to protect other vunerable surfaces. The FT-1000 has a 375W
induction motor driving a large diameter impellor creating an
air movement of 3,060 m³/hr. This air flow is drawn through the
table surface and through a rear upstand inlet along the whole
width of the table. The rubber grommets on the surface protect
the work as well as providing an air gap under the work. Hinged
side upstands can be laid down to allow longer workpieces
to be mounted. There are two pleated filters to capture the
dust in front of the impellor, ensuring clean air returns into
the workshop, whilst a dust tray in the bottom of the cabinet
is easily drawn out for emptying. The FT-1600 model is simply
a large table, twin motored model, with twin filters as well to
allow a much higher airflow over the bigger table. Perfect for
hand sanding or power sanding all types of timbers, but you
should extract from power sanders at source. Easy to maintain
with no tools being required. Solidly built, these machines
provide a cleaner working environment and will be a boon in a
trade workshop.
• Polyester-polyurethane wall,
embedded PVC coated spring
steel wire helix
• Moderately flexible with a
very smooth inside surface
• Extremely abrasion resistant
and almost penetration proof
• Smooth bore means that the likelihood of blockages occuring are
remote
• Temperature range of -40°C to +100°C
• Perfect for high volume waste producing machines
• Clockwise spiral
Inc.vat
Ex.vatCode
Clear Reinforced PU Hose 102mm x 1m £26.95 £22.46505013
Clear Reinforced PU Hose 102mm x 2.5m £63.96 £53.30505014
Clear Reinforced PU Hose 102mm x 5m £122.95 £102.46505015
Clear Reinforced PU Hose 127mm x 1m £32.95 £27.46505016
Clear Reinforced PU Hose 127mm x 2.5m £78.96 £65.80505017
Clear Reinforced PU Hose 152mm x 1m £37.45 £31.21505018
Clear Reinforced PU Hose 152mm x 2.5m £89.95 £74.96505019
Stayput
Extraction
Hose
Accessories
• Semi-rigid hose
Inc.vat
Ex.vatCode
• Stays put when bent into shape
Filter for FT-1000/1600 £31.96
£26.63950380
• Diameter changes over a range of ±20mm when twisted
Comparison Chart - Downdraft Tables
•A
short length suitably adjusted for diameter can be used to
adapt between hoses and machine outlets of different sizes
Model
DT-700U
FT-1000
FT-1600
•A
vailable in grey with a diameter of 102mm(4”) and
Rating
Hobby
Trade
Trade
increments of one metre with the hose extended
Power
375W (230V)
750W (230V)
Air Flow
3,060m³/hr
6,100m³/hr
Inc.vat
Ex.vatCode
Noise Level dB @ 1M
70dB(A)
74dB(A)
Hose 55mm x 1m
£21.96 £18.30200795
Overall L x W x H
970 x 540 x 250mm
1,060 x 670 x 860mm
1,600 x 650 x 900mm
Hose 75mm x 1m
£26.95 £22.46200796
Weight
11.5kg
110kg
198kg
Hose 102mm x 1m
£34.96 £29.13200797
Call free 0800 371822 Mobile friendly 03332 406406 Order online axminster.co.uk/extraction
Dust Extraction.indd 119
119
27/11/2014 16:04
Extraction Accessories
Axminster Flexible
Extraction Hose Kit
• Lengths of high quality wire
reinforced 100mm hose
• Rubber end cuffs to suit
extraction outlets 100-110mm
• Ideal for mobile workshop
chip and dust extractors
Inc.vat
Ex.vatCode
Axminster 4m x 100mm Extraction Hose Kit £74.95 £62.46211597
Axminster 2m x 100mm Extraction Hose Kit £44.95 £37.46501082
Hose Hook
• Keep hoses, ropes and extension
leads stowed away and tidy
• 100mm diameter curve
• Use to support dust extractor hose
• Supplied with three wall plugs and
screws
2
100mm Dust
Extraction Kit
A 100mm ducting kit with most items a home woodworker
Inc.vat
Ex.vatCode
needs to connect machines to an extractor. Comprising 8 X
Hose Hook
£2.26 £1.88600684
910mm lengths of 100mm clear plastic duct, 2 X T junctions, 2 X
90 degree elbows, 2 X 45 degree elbows, 3 x blastgates and 16
x joiners. A pack of 10 wall brackets with screws and wallplugs
are included. All the items are available separately, enabling you
to build a system exactly how you need it. Our other accessories
such as the 990053 Y junction, 500181 Flanged Spigot and
200114 Big Mouth Dust Hood all fit this kit. Add a 410064 kit
and you will get 2 x 3m lengths of flexible hose as well as a
whole host of useful connectors and hoods. The 510412 Earth
Grounding Kit would be worth considering to protect yourself
from possible static build up. Seriously good value for money,
this kit is exactly what the home workshop requires.
100mm Dust Extraction Accessory Kit
• Kit of components
• Useful when connecting up machines to an extraction system
• 2 x 3m lengths of 100mm diameter flexible hose.
• Table saw dust hood
• 100mm Y fitting
• 10 x 100mm pipe clamps
• 4 x 100mm blast gates
• Floor sweeper
• 150mm jointer dust hood
Inc.vat
Ex.vatCode
Dust Extraction kit
£179.95 £149.96210695
100mm x 910mm clear pipe
£16.96 £14.13210697
Joining Splice
£2.95 £2.46210698
45° Elbow
£3.96 £3.30210699
Wall Clip
£1.26 £1.05210700
Numatic 63mm
Dust Extraction Kit Attachment
The Numatic vacuum attachment kit has been designed for
use with the Axminster 63mm Dust Extraction Kit. It allows any
Numatic vacuum machine from a “Henry” upwards to be used
to provide the vacuum to this 63mm system. It simply fits into
a DEK “T” junction and provides a threaded connector for the
2.5m double threaded Numatic hose which is part of the kit.
This hose has the 51mm female thread allowing it to be fitted
Inc.vat
Ex.vatCode
to any standard Numatic vacuum machine. For the purpose that
100mm Extraction Kit
£109.96 £91.63410064
the Axminster DEK is intended, even a Henry would provide
adequate air flow and, when used with HepaFlo bags, top grade
filtration as well. Simple to fit and very effective.
Inc.vat
Ex.vatCode
63mm Dust Extraction Kit Attachment £59.95 £49.96501270
63mm Dust Extraction Kit
• Especially for the smaller
workshop
• Ducting package complete
with elbows, blast gates and
adaptors
• 8 three foot lengths of tube
(63mm diameter)
• 4 x tee joints
• 3 x 45° joiners
• 2 x 90° elbows
• 16 x pipe joiners
• 5 x plastic blast gates
• 10 x wall clips
• 100mm to 63mm adaptor
• Additional parts available
separately
Workshop Metal Ducting Kit
A package of dust and chip extraction metal ducting, enough to
extract from four machines, consisting of:
2 x 2m 150mm Duct
1 x 1 00mm Fixture Joiners
1 x 150mm 90° Elbow
(pack of 5)
Inc.vat
Ex.vatCode
2 x 150-100mm 45° Branch Tee 20 x 100mm Suspension Ring
1 x 150-100mm Reducer
Fixings
Dust Extraction Kit 63mm
£104.95 £87.46410063
3 x 2m 100mm Duct
4 x 1 50mm Suspension Ring
915mm Lengths of 63mm Pipe (4 Pack) £33.46 £27.88410069
10 x 1m 100mm Duct
Fixings
90° Elbow for 63mm DEK
£4.96 £4.13410066
2 x 150mm Joiners
4 x 100mm Blast Gates
Pipe Joiner for 63mm DEK
£1.96 £1.63410070
3 x 100mm Joiners (packs of 5) 5 x 1m x 8mm Threaded Rod
45° Elbow for 63mm DEK
£2.46 £2.05410065
2 x 90° 100mm Elbow
24 x 8 mm Threaded Back
Tee Joiner for 63mm DEK
£4.96 £4.13410072
4 x 45° 100mm Elbow
Plates
Blast Gate for 63mm DEK
£4.45 £3.71410067
2 x 100-100mm 45° Branch Tee 1 x Duct Tape
Securing Clips 63mm (10)
£6.96 £5.80410068
100mm to 63mm Reducer £2.95 £2.46410071
120
Dust Extraction.indd 120
Extra or additional components are available from our Metal
Ducting selection, but this kit would be enough for many small
workshops and take the guesswork out of what you may require.
Ducting lengths may be shortened with a metal cutting hack
saw. Keep the design simple and follow these rules:
• Don’t over complicate the system
• Keep transfer duct as large as the extractor will accept
• Keep flexible duct to a minimum length or none at all if
possible
• Keep branches joining a duct to 45° maximum
• Fit blast gates to maximise efficiency and balance to the system
Inc.vat
Ex.vatCode
Metal Ducting Kit
£699.96 £583.30717045
Free delivery on orders over £50 (UK mainland only) Orders UNDER £50 P&P £4.95
27/11/2014 16:04
Extraction Accessories
Quick Release
100mm Hose
Fixing Clip
100mm x 910mm Clear Pipe for
100mm Dust Extraction kit
An extra length of 100mm x 910mm clear tube for use with the
100mm wall mounted kit to extend it if required.
These handy hose clips
allow the quick changing
Inc.vat
Ex.vatCode
of a 100mm dust extraction hose
100mm x 910mm clear pipe
£16.96 £14.13210697
from one machine to another. Acting
as a large spring and operated by one
hand it could not be easier. Ideal for the hobby woodworker
in a small workshop, now there is no excuse for not using your
extractor. Supplied in a pack of two.
100mm x 100mm
Joining Splice
for 100mm Dust
Extraction kit
Plastic Blastgates
An important accessory in the installation of any dust extraction
system. Blastgates are fitted into the ducts between the
machines and the dust extractor and can be opened or closed
to control the flow to the various machines. 100mm diameter.
Inc.vat
Ex.vatCode
Plastic Blastgate for 100mm Hose
£3.46 £2.88340921
Inc.vat
Ex.vatCode
Quick Release 100mm Hose Clip (Pair)
£9.95 £8.29210323
An extra 100mm x 100mm joining splice for use with the
100mm wall mounted ducting kit to extend it if required.
Inc.vat
Ex.vatCode
Joining Splice
£2.95 £2.46210698
Quick Fit
Hose Fixing
Clips
100mm Wall Clip
for 100mm Dust
Extraction Kit
Aluminium Blastgates
Aluminium blastgates, stronger than plastic and with a locking
A simple steel fixing clip with plastic butterfly handle for speed
screw.
and ease of use and ideal for most 100mm hose applications.
Especially useful when blockages occur; they can be rectified
Inc.vat
Ex.vatCode 2
Inc.vat
Ex.vatCode
immediately without the need for screwdriver or clipdriver.
Blastgate for 100mm Hose
£9.46 £7.88340920
Wall Clip
£1.26 £1.05210700
Blastgate for 125mm Hose
£11.46 £9.55200071
Inc.vat
Ex.vatCode
Blastgate for 150mm Hose
£12.96 £10.80200070
90 to 110mm Clip (each)
£1.75 £1.46500480
90 to 110mm Clip (Pkt 5)
£7.45 £6.21500481
70 - 90mm Clip
£1.56 £1.30211999
110 - 130mm Clip £1.96 £1.63950501
An extra 100mm wall clip for use with the 100mm wall mounted
ducting kit to extend it if required.
100mm x 45
Degree Elbow
for 100mm Dust
Extraction kit
An extra 100mm 45 degree elbow for use with the 100mm wall
mounted ducting kit to extend it if required.
Inc.vat
Ex.vatCode
45° Elbow
£3.96 £3.30210699
Elbows
Hose Fixing Clips
This elbow gives a gently rounded
curved bend which produces less
resistance to the air as well as
minimising the risk of blockage.
Used for securing hose ends and also for many other
applications. Second to none on exhaust repairs! 510405 is a
flexible driver with a hexagon socket at the end - the quick and
safe way to tighten up your clips, available separately.
Flanged Spigots
This adaptor has a whole range of uses including making the
hose connections on home-made dust extractor hoods and
cowls from thin section plywood. 100mm adaptor made from
ABS plastic and measures 205mm square.
Inc.vat
Ex.vatCode
Inc.vat
Ex.vatCode
Inc.vat
Ex.vatCode
51
to
70mm
Clip
(Pkt
3)
£3.25
£2.71510401
90° ABS Elbow for 100mm Hose
£5.46 £4.55410258
ABS Flanged Spigot for 100mm Hose
£2.46 £2.05500181
70 to 90mm Clip
£1.45 £1.21410477
95 to 115mm Clip
£1.75 £1.46410486
110 to 140mm Clip
£1.96 £1.63410487
This T Junction hose ducting
135 to 165mm Clip
£2.26 £1.88410488
accessory is manufactured from
185 to 210mm Clip
£2.26 £1.88951617
high quality ABS plastic and is
Flexible Clip Driver
£13.96 £11.63510405
strong with a smooth internal
bore. The outside diameter of the
fitting allow for a snug fit into the
appropriate size of flexible hose
and secured using fixing clips.
T Junctions
Inc.vat
Ex.vatCode
ABS T Junction for 100mm Hose
£6.46 £5.38900337
Y Junctions
Dust Extraction System
Grounding Kit
This Y Junction hose ducting
accessory is strong with a
smooth internal bore. The outside
diameters of the fitting allow for
a snug fit into the appropriate
size of flexible hose and secured
using fixing clips.
WARNING
Dust and debris moving inside the plastic extraction hose may
cause a build up of static electricity. This can cause a potential
hazard especially with fine dust. Dust extraction systems are a
great deal safer if properly grounded. This kit contains 12metres
of copper wire and all the necessary adaptors to ground a system.
Inc.vat
Ex.vatCode
ABS Y Junction for 75mm Hose
ABS Y Junction for 100mm Hose
£4.45 £3.71990052
£6.46 £5.38990053
Big Mouth
Dust Hood
A large rectangular funnel, 410 x 325mm and 270mm deep
ending in a circular spigot to fit 100mm diameter hose. The Big
Mouth Dust Hood will fit directly onto the Axminster Heavy
Duty Variable Height Dust Extraction Hood (410073), providing
a larger catchment area, or it can be used alone behind a radial
arm saw or other machine with no specific extraction port.
Inc.vat
Ex.vatCode
Inc.vat
Ex.vatCode
Dust Hood
£11.95 £9.96200114
Dust Extraction Grounding Kit
£19.96 £16.63510412
Call free 0800 371822 Mobile friendly 03332 406406 Order online axminster.co.uk/extraction
Dust Extraction.indd 121
121
27/11/2014 16:04
Extraction Accessories
Universal Dust
Port Bracket
This is a very useful device enabling
the secure positioning of a 100mm
extraction hose or dust port in many
different ways. The saddle and hose
clip have a very strong magnetic
mount which can be used alone to
attach to a ferrous metal surface whilst
the supplied clamp can be used to
position the bracket either vertically
or horizontally. Especially useful for
woodturning or bench work.
Numatic 2.9m x 32mm Hose
Inc.vat
Ex.vatCode
Dust Port Bracket
£15.96 £13.30210299
Axminster Bendi-Hoze
2
Bendi-Hoze is an articulated tube 75
mm diameter by 610mm long. It is
designed to attach to an extractor
and can be adjusted so that the
inlet is in the best position to
extract from a lathe, bench sander,
soldering station, power tool etc. The
kit includes a 75mm hose adaptor and
three extraction nozzles. The first nozzle
is a 115 x 90mm funnel, the second a
115mm round funnel and the third a
narrow vacuum nozzle. An additional
600mm extension hose is available either as an extension or to
use a number of the hose ends at the same time.
Floor Gulper Attachment
This is a 2.9 metre power tool hose with a 51mm threaded
cuff, to fit the 210616 adaptor cuff. Will also fit all Numatic
vacuum cleaners and extractors. Used with 610325 stepped
rubber reducer, this can be adapted to fit virtually all hand held
power tools with an extraction port or most small bench top
woodworking machines.
Inc.vat
Ex.vatCode
2.9m 32mm hose
£21.96 £18.30210551
Gulp up all your shavings and dust with this handy attachment.
Simply connect it to a length of 100mm flexible hose linked
into your workshop extractor and clean up! With a convenient
handle and castor wheels you will whizz round your workshop
in no time. Supplied complete with a blastgate, you can leave
this rigged up permamently. Requires an extractor size of
1,000m³/hr as a minimum to work effectively, so many small,
portable extractors are quite suitable.
Inc.vat
Ex.vatCode
Floor Gulper Attachment
£39.96 £33.30211551
Numatic Stepped Hose Reducer
Inc.vat
Ex.vatCode
Bendi-Hoze Kit
£35.95 £29.96056001
Extension 600mm £25.45 £21.21056003
Light Duty
Variable Height
Extraction Hood
This is a very useful adaptor for connecting extraction hoses to
a variety of power tools and other small machines. Can be used
as it is or trimmed to length to suit a range of outlet diameters.
Dimensions are: length 160mm, small end internal diameter
22mm, external diameter 30mm, large end internal diameter
38mm, external diameter 45mm.
A simple dust extraction hood
Inc.vat
Ex.vatCode
mounted on an adjustable
Stepped Hose Reducer
£14.46 £12.05610325
height stand. Very useful
for situations where direct
connection to a machine
is not possible, such as
woodturning. Having a robust
ABS hood fastened to a 100mm
diameter metal tube, this is
easily connected to flexible
extraction hose leading from
your extraction system. The
steel stand gives a useful height
range from 750-1,200mm and
has 3 feet, so no wobbles on
your uneven workshop floor! The
hood has an inlet of 320 x 35mm
creating a good airflow, an
A hose kit comprising 2.9m of 32mm hose and a stepped
extractor of at least 750m3/hour
rubber reducer. The hose will fit onto any Numatic vacuum
is recommended. Will not accept
cleaner or workshop extractor whilst the stepped rubber
Big mouth dust hood (200114)
reducer will allow connection onto almost any hand held power
tool and some small bench top woodworking machines. An
Inc.vat
Ex.vatCode
ideal solution for extraction in many circumstances. N.B. If
Variable Height Extraction Stand
£29.95 £24.96950030
using with the RDC100 or other 100mm vacuum extractors
the adaptor 210616 will also be required.
Numatic Power Tool
Extraction Hose
Heavy Duty Variable Height
Extraction Hood
For extracting waste from a lathe or other dust source where
direct connection to the machine is not possible or convenient.
Adjustable in height from 710mm to 1220mm with tilting
facility to enable the collection slot to be positioned at the
best possible angle. The hood is made from cast alloy and the
collection slot measures 300 x 50mm. It is easily connected
to 100mm flexible hose leading to an extractor of around
1,000m3/hr. The 200114 Big Mouth Hood can be fitted in place
of the nozzle to give a 410 x 405mm collection area. Extraction
from a woodturning lathe can present problems, using the
200797 100mm Stayput extraction hose fitted into this nozzle
and set up behind the lathe makes for very efficient extraction.
Inc.vat
Ex.vatCode
Extraction Hose & Adaptor
£32.95 £27.46718085
Axminster
Flexible
Rubber Cuffs
These rubber cuffs have several potential uses: connecting
ducting directly to static machines, joining ducting sections in
slight curves being just two. Made from heavy duty rubber and
supplied with two compression clips. Available in two sizes: 100
and 65mm internal bore.
Numatic
Reducer End Cap
100mm -51mm
Numatic reducer end cap 100mm - 51mm. Allows the fitment of
the 718085 power tool hose to a 100mm sized hose or dust tube.
Inc.vat
Ex.vatCode
Inc.vat
Ex.vatCode
Inc.vat
Ex.vatCode
Variable Height Dust Extraction Hood £84.96 £70.80410073
65mm Flexible Rubber Cuff
£6.46 £5.38508324
Big Mouth Dust Hood
£11.95 £9.96200114
100mm Flexible Rubber Cuff
£8.46 £7.05508325
100mm to 51mm Reducer
£14.95 £12.46210616
122
Dust Extraction.indd 122
axminster.co.uk/signup for our exclusive email offers
27/11/2014 16:05
Extraction Accessories
510074
510066
Rubber Adaptors
Quick Fit
Metal Straps
Two useful items for connecting small
diameter pipes into ducted systems.
The ribbed part plugs into either 4”
or 110mm ducting and either 32mm
or 50mm pipes will push directly into
the inner holes. No further fixings should be required.
Good strong metal spring clips that can be cut to size to suit the
diameter required. Join two together for larger circumferences.
Inc.vat
Ex.vatCode
Quick Fit Metal Strap to 1140mm(45”)
£7.45 £6.21800425
Quick Fit Metal Strap to 1450mm(57”)
£7.45 £6.21800426
Inc.vat
Ex.vatCode
Bung 110mm-32mm
£12.96 £10.80341102
Bung 110mm-50mm
£14.46 £12.05341103
102mm Hose Cuff
510072
Hose Reducers
510073
Axminster
Auto-Extract
Controller Unit
This is an easily fitted flexible rubber
machine cuff for attaching hose to
Used for converting one diameter of hose to another. Made
machinery. One end has a moulded
from ABS plastic, with the exception of 510074 which is made
thread that screws directly onto our
from galvanised steel.
100mm clear hose, the other end
This range of controllers enables automation of
of the cuff is a snug fit onto a 102Inc.vat
Ex.vatCode
your dust extraction system, giving more convenient
110mm diameter machine extraction
107mm OD / 102mm ID
working and saving both electricity and heat (when
port or use with quick release hose clips (210323) on 100mm ports.
to 52mm OD / 46mm ID
£8.46 £7.05510066
venting externally). Sensors are attached to each motor
Clockwise spiral. Turn the cuff inside out if it does not match your
99mm OD / 94mm ID
and then connected into the controller. The sensors detect
hose spiral. It makes for an easy connection, and re-connecting
to 75mm OD / 69mm ID £1.75 £1.46510072
the magnetic field generated when a machine’s motor is
the extractor from one to machine to another as simple as possible.
133mm OD / 127mm ID
switched on and the dust extractor is then automatically
to 101mm OD / 92mm ID
£3.25 £2.71510073
Inc.vat
Ex.vatCode
started.The controller can connect up to five machines but, by
150-125mm
£13.96 £11.63510074
102mm Hose Cuff
£19.96 £16.63610697
adding Auto-Expand units, any number of machines can be
added. Each Auto-Expand unit will accommodate an additional
five motors. The Auto-Extract controller is available in 230V
1ph 13A or 16A versions or a 415V 3ph neutral + earth version
2
allowing control of dust extractors up to 6kW. These units operate
the extractor directly; you will need to bypass the original switch
system. Sensors are available separately, depending on the
length of cable required. Additional accessories include a Sensor
A quick and neat way of joining two
Switch which allows a machine sensor to be disabled when dust
A stepped ABS hose adaptor with seven
lengths of hose together. The hose is
extraction is not always required on a particular machine. Made
different sizes that can form perhaps
secured by fixing clips. Available for 75 or
in Axminster with UK sourced components. N.B. A sensor cable
two or more adaptors. Simply cut the
100mm hoses only.
is not supplied and will need to be purchased separately.
section you require with a fine toothed
Inc.vat
Ex.vatCode
saw. Diameters are 25mm, 50mm, 63mm,
Inc.vat
Ex.vatCode
Joiner for 75mm Hose
£2.76 £2.30510028
75mm, 100mm, 125mm and 150mm
Auto Extract 13A
£189.96 £158.30310458
ABS Joiner for 100mm Hose
£2.95 £2.46510029
(sizes stated are outside diameter).
Auto Extract 16A
£209.95 £174.96310459
Inc.vat
Ex.vatCode
Auto Expand Unit
£149.95 £124.96310460
Stepped Adaptor
£4.45 £3.71990091
Sensor 3m Cable
£9.96 £8.30310464
Sensor 6m Cable
£10.96 £9.13310465
Although soil pipe is frequently utilised
Sensor 12m Cable
£12.96 £10.80310466
for dust extraction ducting, one problem
10m Extension Cable £10.96 £9.13310463
which often crops up when using it is
Sensor Switch
£39.96 £33.30310461
that the outer diameter of the soil pipe
is some 112mm or approximately 4.5”. To
get around this problem we offer a special
adaptor, 900063, to convert from the soil
pipe to a 4” hose. Duct Tape (410221) can
Router table set-ups and some
be used to produce a more secure joint.
sawbenches can sometimes present
Inc.vat
Ex.vatCode
extraction problems, with extraction
100mm Soil Pipe Adaptor £6.25 £5.21900063
often required from both above and
Gaffa Tape 50mm x 50m
£5.76 £4.80410221
below the table. This adaptor enables you to achieve this by
Multiple
Stepped Hose
Adaptor
Hose Joiners
Soil Pipe Adaptor
Axminster Dust
Extraction
Adaptor 100mm
Manual Switch for
Auto Extract units
having a 100mm flanged outlet with a 62mm inlet at the top.
A cabinet or enclosure will be required to extract from with a
hole made to accept the adaptor. When extraction is connected
using a standard 100mm hose, a separate 63mm hose can
then be attached to the top of the adaptor and connected to
either a dust port on the router table fence or the crown guard
of the saw bench. We are sure there must be many other dust
We have listed our common
extraction situations where this fitting would prove invaluable.
waste sacks, together with their
Inc.vat
Ex.vatCode
layflat size (that is the width of
Adaptor 100mm
£8.46 £7.05502568
the bag if laid flat on the floor
i.e. half the circumference).
They can be used for general
waste collection as well as for
dust extraction. Supplied as a
pack of 10.
Heavy-Duty
Dust Extractor
Waste Sacks
Hose Reducer
100mm O/D to
50mm O/D
This accessory is a manual switch control unit used where you
may wish to operate the extraction manually, rather than use
the automatic function. Supplied with 6 metres of cable with
fitted jack plug ready for use.
Inc.vat
Ex.vatCode
Manual Switch for Auto Extraction Units £59.95 £49.96950507
Axminster Controller
Unit Sensor Switch
Inc.vat
Ex.vatCode
560 x 915mm Waste Sack Red (Pkt 10) £11.46 £9.55340068
1,065 x 1,370mm Waste Sack Green (Pkt 10) £26.95£22.46900243
This switch will allow a machine to be operated when extraction is
785 x 940mm Waste Sack Orange (Pkt 10) £13.96 £11.63410241
Hose reducer 100mm OD (94mm ID) to 50mm OD (45mm ID).
not required, thus saving the extractor from running unnecessarily.
735 x 1,190mm Waste Sack Black (Pkt 10) £15.96 £13.30600223
Inc.vat
Ex.vatCode
Inc.vat
Ex.vatCode
760 x 1,065mm Waste Sack Blue (Pkt 10) £14.95 £12.46800345
785 x 1,200mm Waste Sack Yellow (Pkt 10)£17.46 £14.55501187
Hose Reducer 100mm to 50mm
£1.75 £1.46200092
Sensor Switch
£39.96 £33.30310461
Call free 0800 371822 Mobile friendly 03332 406406 Order online axminster.co.uk/extraction
Dust Extraction.indd 123
123
27/11/2014 16:05
The most common question asked is what size extractor do I need?
Many manufacturers will state the volume of air required for each
machine in their manual. If not, note the size of the extraction port
and use the chart below
outlet size
50
100
125
150
200
volume of air reqd
200 m³/hr
700 m³/hr
1100 m³/hr
1600 m³/hr
2800 m³/hr
Example: for a single machine with a 100mm port an extractor of
a minimum of 700m³/hr will be sufficient. For multiple machines
count the number of extraction ports per size, multiply the number
of each size by the volume of air required. Then add the results
per outlet size to give you a total volume of air required. This total
is for all the machines operating at the same time. You then must
decide which and how many machines will be used at the same
time. Divide the total volume of air required by this number and
add 500m³/hr. Choose an extractor that gives the airflow required
by your calculations. Look at the main inlet size of the extractor, this
is the size of the main duct to be used. In larger systems the ducting
should get larger towards the extraction unit as more machines
that are in use are added to maintain the correct air speed in the
duct. This is very important; if the airflow is too low a build up of
dust and debris will occur and is a fire and explosion risk. If the air
speed is high then the system will be noisy but there will be no
deposits in the ducting. Always use blastgates to close off airflow to
machines that are not in use.
Ducting
2
Available in a variety of diameters to suit all applications.
Sections of duct can be joined together with short joining
lengths, which fit on the inside of the duct. The perfect solution
for extraction systems.
Ducting
Steel
Reducers
Reducing adaptors are for stepping down in ducting size, i.e.
from 150mm to 125mm. Available in a variety of sizes. These fit
inside the ducting for a smooth air flow.
Basic design
• Keep it simple, don’t over complicate the system
• K eep it straight, ducting runs should all be straight with as few
bends as possible
• K eep transfer duct as big as required by the extractor, this should
get larger towards the extractor
• K eep flexible duct to a minimum. If the machine cannot be
connected to the system by solid ducting only then should flexible
ducting be used for the final connection.
• K eep branches joining the duct to a maximum of 45° When
branches join the main duct ideally they must enter at the side
or the top at an angle of a maximum of 45° towards the direction
of flow.
• Fit Blastgates to maximise efficiency and balance the system
Inc.vat
Ex.vatCode
100-80mm
£12.46 £10.38410083
125-100mm
£12.46 £10.38410084
150-100mm
£14.95 £12.46410085
150-125mm
£13.96 £11.63510074
180-150mm
£21.96 £18.30951628
200-150mm
£18.96 £15.80951629
Steel Saw Table
Adaptors
With so many saw tables now with
extraction both under the saw and over the
The negative pressure inside the ducting draws air into the system.
top on the saw guard, it is often the case
Incorrect sizing of the duct, too many bends coupled to lots of
that the top guard extraction point is never
flexible hose induces losses into the system and in badly designed
used because there is no easy means of
systems this is akin to leaving the handbrake on in a vehicle.
joining in the smaller hose. Here is a simple answer: two galvanised
adaptors which go in line with the 100mm hose and provide a
Inc.vat
Ex.vatCode
handy connection for the top guard hose, either 50mm or 38mm.
100mm X 1m Ducting
£9.96 £8.30410229
125mm X 1m Ducting
150mm X 1m Ducting
200mm x 1m Ducting
100mm X 2m Ducting
125mm x 2m Ducting
150mm x 2m Ducting
200mm x 2m Ducting
£11.95
£14.95
£20.95
£17.95
£21.96
£27.96
£41.95
£9.96951611
£12.46951612
£17.46951613
£14.96410230
£18.30951614
£23.30951615
£34.96951616
Inc.vat
Ex.vatCode
Y Junction 100-50mm
£40.96 £34.13810353
Y Junction 100-38mm
£40.96 £34.13810352
Black GP Hose 38mm x 2.5m
£22.96 £19.13200783
Suspension Rings
Simple clips to hold the ducting either
suspended from a ceiling or standing
out from a wall. A variety of diameters
A short length of tube used to join
available. The clips have an M8 threaded
A short length tube used to join two
two lengths of ducting together. It fits
hole. Use M8 threaded plated studding, available in 1m or 3m
fixtures together. It fits over the outside of
inside the duct and can be secured either
lengths. Each clip requires a M8/10 back plate (210502) and
the fixtures (bends , T or Y junctions etc.) and can
with duct tape or short self tapping screws. Pack of 5.
M8 studding (410113). By using studding the ducting can be
be secured either with duct tape, self-tapping screws or pop rivets.
suspended from the ceiling at the height required. By using short
Inc.vat
Ex.vatCode
The 100mm comes in a pack of 5, the other sizes are in packs of 1.
lengths of studding, ducting can be mounted directly onto a wall.
Duct Joiners 100mm (Pkt 5)
£14.95 £12.46410228
Inc.vat
Ex.vatCode
Duct Joiner 125mm (ea)
£3.25 £2.71951607
Inc.vat
Ex.vatCode
Fixture Joiner 100mm (Pkt 5)
£14.46 £12.05410232
Duct Joiner 150mm (ea)
£3.46 £2.88951608
100mm £5.26 £4.38211466
Fixture Joiner 125mm (ea)
£3.25 £2.71211461
Duct Joiner 200mm (ea)
£3.76 £3.13951609
125mm £5.26 £4.38211467
Fixture Joiner 150mm (ea)
£3.25 £2.71211462
Ducting Joiners
Fixture Joiners
Fixture Joiner 200mm (ea)
Steel Elbows
150mm 200mm £3.46 £2.88211463
Aluminium Blastgates
£5.46 £4.55211468
£6.46 £5.38211469
Threaded Plated Studding
Aluminium blastgates, stronger than
To provide a smooth bend within
plastic and with a locking screw.
a duct system. Fits inside the duct
Used for mounting suspension rings to ceilings or walls.
tubing. Use Fixture Joiners to
Inc.vat
Ex.vatCode
Inc.vat
Ex.vatCode
connect elbows together.
Blastgate for 100mm Hose
£9.46 £7.88340920
8mm x 1m
£2.76 £2.30410113
Inc.vat
Ex.vatCode
Blastgate for 125mm Hose
£11.46 £9.55200071
90° Elbow 100mm
£9.96 £8.30410013
Blastgate for 150mm Hose
£12.96 £10.80200070
90° Elbow 125mm
£12.46 £10.38951601
90° Elbow 150mm
£18.46 £15.38951602
90° Elbow 200mm
£24.96 £20.80951603
45° Elbow 100mm
£7.96 £6.63400499
45° Elbow 125mm
£9.46 £7.88951604
90° and 45° twin bends are used
Plated back plates for use with all suspension rings. Threaded
45° Elbow 150mm
£13.45 £11.21951605
when splitting the system off, i.e.
M8 and with 2 mounting holes. Use M8 studding to mount the
45° Elbow 200mm
£17.95 £14.96951606
to lead into another room or to the
ducting the appropriate distance from the ceiling or wall.
other side of a workshop. Offering a
Twin Bends
M8 Threaded
Back Plate
Branch Tee
smooth air flow with many advantages over the more usual 90°
Inc.vat
Ex.vatCode
Tee junction. A selection of 4 sizes and 2 angles available.
Back Plate
£3.46 £2.88210502
Branch Tees are the best way to lead off to
Inc.vat
Ex.vatCode
a machine from a duct system. Having a
100mm 90° Twin Bend
£66.96 £55.80951630
smooth inner surface and a 45° angle there
150mm 90° Twin Bend
£84.96 £70.80951632
is no obstruction to the airflow. Also, these
A simple 0-5kPa manometer, used to
100mm 45° Twin Bend
£48.96 £40.80951634
are available in a range of sizes to suit the
monitor the air flow within ducting used as
150mm 45° Twin Bend
£54.96 £45.80951636
duct and machine extraction outlet.
part of a dust/chip extractor system (LEV).
The fitting of a manometer on each “hood”,
Inc.vat
Ex.vatCode
e.g. extraction point, is recommended
100mm off 100mm at 45°
£35.95 £29.96951618
as a method of daily monitoring of the
100mm off 125mm at 45°
£36.96 £30.80951619
End caps are used to seal the end of ducting. Useful
system’s performance by the HSE in their
100mm off 150mm at 45°
£37.96 £31.63951620
to allow an extension at a later date, or to provide a
LEV checklist for employers. This unit provides an “at a glance”
100mm off 200mm at 45°
£43.96 £36.63951621
permanent seal.
monitoring of the system at each extraction point each time it is
125mm off 125mm at 45°
£37.96 £31.63951622
used, thus satisfying the requirements under the HSE’s guidance.
Inc.vat
Ex.vatCode
125mm off 150mm at 45°
£39.96 £33.30951623
These are used by our own Extraction Installation team when
125mm off 200mm at 45°
£45.96 £38.30951624
100mm £4.26 £3.55211476
fitting new systems.
150mm off 150mm at 45°
£47.95 £39.96951625
125mm £5.26 £4.38211477
Inc.vat
Ex.vatCode
150mm off 200mm at 45°
£51.96 £43.30951626
150mm £5.76 £4.80211478
200mm off 200mm at 45°
£57.96 £48.30951627
200mm £7.45 £6.21951610
Manometer, 0-5kPa
£94.96 £79.13210675
Manometer 0-5 kPa
End Cap
124
Dust Extraction.indd 124
*SAVE with a bulk discount – see online axminster.co.uk or call 03332 406406
27/11/2014 16:05
Numatic
£124.96
Numatic Easy Ride
AiroBrush
Ex.vat: £104.13
Code: 508316
The AiroBrush is an exceptional floor nozzle developed to provide
quick and efficient carpet care. The rotary action is especially
effective for the removal of threads and pet hairs. It grooms the
whole carpet and will allow power brush results where uprights
can rarely go. A truly high performance power brush suitable for
the Henry range and other machines with a 32mm pipe fitting.
Inc.vat
Ex.vatCode
Easy Ride AiroBrush
£47.95 £39.96702820
Numatic HVR-200 A2 Henry Vacuum Cleaner
Meet the new ECO Henry which complies with the new ECO
Design Regulations. The full TwinFlo two-stage professional
motor gives exceptional performance with an ‘A’ rated energy
value. The new 580W TwinFlo motor provides almost exactly the
same suction power with a 50% energy saving. All the favourite
attributes of toughness and ease of use are still there to ensure
long life and exceptional performance. This model is equally at
home in your house, workshop or carried in the van for use on
site where Henry will swallow your mess with ease. Features
include a 10m cable with re-wind, stainless steel wand with
sturdy tools and hose, and a giant Tritex filter to ensure what
goes in stays in. The HepaFlo filtration bags have a neck closure
for safe waste disposal and add a layer of filtration. The addition
of the quilted Microtex filter (610327) when used with Hepa-Flo
filter bags will upgrade these machines to the full British Allergy
Foundation standards. An odour suppression filter (610328)
Numatic 2.9m x
32mm Hose
is also available. Supplied with four HepaFlo filter bags, 2.5m
flexible hose, stainless steel floor wand, floor cleaning head for
hard and soft floors, small brush heads and a crevice tool ideal
for the car! There is a reason why these are found in hotels all
around the world - they just go on and on and on.
This is a 2.9m power tool hose with a 51mm threaded cuff, to
fit the 210616 adaptor cuff. Will also fit all Numatic vacuum
cleaners and extractors. Used with 610325 stepped rubber
reducer, this can be adapted to fit virtually all hand held
power tools with an extraction port or most small bench top
woodworking machines.
Specification - HVR-200 A2 Henry
HVR-200 A2
Model
RatingTrade
Power580W
9 litres
Container Volume
2,520 litres/min
Air Volume
Suction2,000mm
42 litres/sec
Air Flow
340 x 340 x 370mm
Overall L x W x H
Weight6.6kg
Inc.vat
Ex.vatCode
2.9m 32mm hose
£21.96 £18.30210551 2
Numatic Stepped
Hose Reducer
This is a very useful adaptor for connecting extraction hoses to
a variety of power tools and other small machines. Can be used
as it is or trimmed to length to suit a range of outlet diameters.
Dimensions are: length 160mm, small end internal diameter
22mm, external diameter 30mm, large end internal diameter
38mm, external diameter 45mm.
Inc.vat
Ex.vatCode
Stepped Hose Reducer
£14.46 £12.05610325
Numatic Power
Tool Extraction
Hose
A hose kit comprising 2.9m of 32mm hose and a stepped
rubber reducer. The hose will fit onto any Numatic vacuum
cleaner or workshop extractor whilst the stepped rubber
reducer will allow connection onto almost any hand held power
tool and some small bench top woodworking machines. An
ideal solution for extraction in many circumstances. N.B. If
using with the RDC100 or other 100mm vacuum extractors
the adaptor 210616 will also be required.
£99.96
Ex.vat: £83.30
Code: 508317
Inc.vat
Ex.vatCode
Extraction Hose & Adaptor
£32.95 £27.46718085
Numatic NSP 180 A2
Vacuum Cleaner
Numatic Filter
Bags for Henry
& Friends
This vacuum is a very clever design based on simplicity. The new
580W motor has the same suction power as before but meets
the new ECO Design Regulations with an ‘A’ rated energy value.
The HepaFlo filter bags ensure the highest efficiency suction
combined with clean and convenient emptying when full. The
unique caddy, on top, provides somewhere for the cable, tools,
duster and polish. This cheerful little vacuum cleaner will follow
you around and make light work of all your cleaning chores.
Powerful enough for industrial use and light enough for the
home user. Made in the UK and with a 2 year warranty for peace
of mind (except tools). Replacement HepaFlo Filter Bags NVM1CH available separately in packs of 10 (210628).
Genuine Numatic
Filter Bags for Henry,
friends and other
Numatic vacuums.
Specification - NSP 180 A2
Numatic NSP 180 A2
Model
RatingIndustrial
Power580W
8 litres
Container Volume
1,800 litres/min
Air Volume
Suction2,000mm
340 x 340 x 340mm
Overall L x W x H
Weight5.8kg
Inc.vat
Ex.vatCode
NVM-1CH (Pkt 10)
£9.46 £7.88210628
NVM-3AH (Pkt 10)
£16.96 £14.13211199
NVM-4BH (Pkt 10)
£19.96 £16.63211015
NVM-2BH (Pkt 10)
£11.95 £9.96211175
Std Repl Tritex Filter
£25.96 £21.63702821
“Henry” Microtex Filter
£40.96 £34.13610327
Call free 0800 371822 Mobile friendly 03332 406406 Order online axminster.co.uk/extraction
Dust Extraction.indd 125
125
27/11/2014 16:05
Vacuum Cleaners
£244.96
Ex.vat: £204.13
Code: 508330
2
£499.96
Ex.vat: £416.63
Code: 610326
Numatic NVDQ900-2
Vacuum Cleaner
Numatic NQS250B-B2
Vacuum Cleaner
£289.96
The all-steel construction of today’s NQS250B model is where
the Numatic story started. They learnt from the 250 that the
commercial cleaning business was rough and tough but, having
said that, the majority of their early machines are still working
20 or more years later. After all those years the NQS250B
is better than ever. The all-steel deep-drawn power head
incorporates the patented Microtec noise reduction system;
the new ECO high efficiency motor provides even more suction
with almost half the power.The Nucable plugged replaceable
cable system is standard as is the blower facility and diffuser
attachment. Filtration is to the Tritex standard and the container
is also a single deep-drawn steel pressing with superb fourwheel mobility and stability. The standard 32mm accessory
kit is to the same high standard, even down to stainless
steel tubes and full size combination floor nozzle. Without
doubt, yesterday’s quality standards, to which Numatic have
added many improved features, have resulted in tomorrow’s
performance standards. The best of both worlds.
Ex.vat: £241.63
Code: 508331
Numatic
NQS350B-B2 Vacuum Cleaner
The NVQS350B-22 low noise vacuum is tough - very tough. This
is the model that has proved it can outlast the rest in the most
arduous of applications. The all-steel power head is low noise,
and with the new ECO high efficiency motor, it is just about
as good as you can get, even down to the Nucable plugged
replaceable cable system and an air blower facility. Filtration
is to the Tritex standard with the added advantage of giant
HepaFlo 15 litre dust bags, and easy, clean emptying. The allsteel container is mounted on, but removable from, a rugged
wheeled tubular chassis which really does give it ‘go-anywhere’
mobility. A full range of 32mm accessories of an equally high
standard is supplied for all cleaning applications.
TThe NVDQ 900 is a Duplex (two motored) machine equipped
with 2, TwinFlo two stage industrial motors providing unrivalled
performance standards. It’s manoeuvrability makes it ideal for
numerous trades where it must frequently be moved from place
to place while still requiring a large capacity.The filtration level of
0.5 micron @ 99% gives a great level of operator protection, the
Hepa-Flo bags keeping the waste in when emptying the machine.
Structofoam is a unique material specification that has superb
strength and impact resistance allowing machines to be truly
rugged yet without a weight penalty.Giant rear wheels and front
castors provide excellent mobility and transit even over tough
ground conditions. The standard 38mm accessory kit includes
an extra long double swivel hose, stainless steel tubes, 400mm
Structofoam floor nozzle and additional cleaning tools.
The new AirFlo design improves performance some 30% when
used together with the Hepa-Flo dust bag system, providing the
ideal specification for machines expected to work extended hours
with little loss of performance. A tough cleaner for tough jobs.
Accessories
Inc.vat
Ex.vatCode
Hepaflo Filter Bags NVM-4BH (Pkt 10) £19.96
£16.63211015
Comparison Chart - Numatic Vacuum Cleaners
NQS250B-B2
NVQS350B-B2
Model
Rating
Trade
Industrial
Power
780W 230V
780W 230V
Container Volume
9 liters
14 litres
Air Volume
2,400l/min
2,400 litres/min
Noise Level
56dBa
56dB
Suction
2,600mbar
2,600mbar
Overall L x W x H
340 x 340 x 395mm
395 x 350 x 560mm
Weight
8.6kg
11.7kg
126
Dust Extraction.indd 126
NVDQ900-2
Industrial
2.2kW
40 litres
5400 litres/min
66dB
2,000 mbar
800 x 490 x 880mm
25kg
axminster.co.uk/signup for our exclusive email offers
27/11/2014 16:05
Wet & Dry Vacuum Cleaners
2
£249.96
Ex.vat: £208.30
Code: 500418
£189.96
£959.95
Ex.vat: £158.30
Code: 990003
Ex.vat: £799.96
Code: 702712
Numatic George GVE370-2
Wet or Dry Vacuum Cleaner
The true “all in one” machine that is totally at home be it in the
wet or the dry. This classic “all in one” is genuinely the family
friend, dry vacuuming, wet vacuuming, scrubbing and drying
hard floors, deep cleaning the carpet, cleaning the upholstery,
unblocking the sink, you name it, George is your man.
The combination of our highly efficient TwinFlo’ bypass vacuum
motor and our powerflo’ pump system provides you with
professional cleaning standards, any time, anywhere, ensuring
exceptional results.
The George design is in itself based entirely on our Cleantec
professional range of machines; designed to work extensively
and for long hours and functioning to a professional standard.
When it comes to dry vacuuming you have big filters, use of
HepaFlo dust bags, and you have a superb combination floor
nozzle. In the wet mode, a simple exchange of the dry filter for the
safety float valve allows any number of wet tasks to be achieved.
Numatic WV380-2
Wet or Dry Vacuum Cleaner
The WV-380s are, by design, wet or dry vacuum cleaners that
perform totally without compromise in either mode. When
you want to operate as a dry machine performance must be as
good as a dry-only machine, with big filters and the option of
giant HepaFlo disposable dust bags ensuring a high standard of
operation. Similarly, when required for wet work, a quick switch
of the dry filter for the wet float valve and a change of floor
nozzle will give you equally professional performance and a
clean, dry floor at the end of it all. Extremely ruggedly built, with
Numatic’s patented Structofoam container and amply powered
by a 1,200W “Twinflo” motor and supplied with a full wet and
dry floor cleaning kit with stainless steel tubes.
Numatic NTD 2003-2
Wet & Dry Vacuum Cleaner
With a large capacity coupled with outstanding performance
this vacuum can be used for a multitude of tasks such as
cleaning up flooded areas, spillages and large amounts of
waste debris. It incorporates two 1,200W “Twinflo” bypass
vacuum motors. A “Permatex” secondary filter is fitted above the
metal float assembly providing a wet/dry option when in use.
Filtration levels can be further enhanced by adding additional
filtration. A 76mm cyclonic entry with 51mm-32mm reducer
is fitted as standard enabling the vacuum to be used with a
multitude of accessories. The stainless steel drum is fitted with
Accessories
Accessories
a 32mm dump hose for ease of emptying, and a heavy duty
Inc.vat
Ex.vatCode
Inc.vat
Ex.vatCode
transit chassis. Each vacuum comes complete with a 38mm kit
Hepaflo Filter Bags NVM-2BH (Pkt 10) £11.95
£9.96211175
Hepaflo Filter Bags NVM-2BH (Pkt 10) £11.95
£9.96211175
BB7 as standard.
Comparison Chart - Wet & Dry Vacuum Cleaners
GVE370-2
Model
Trade
Rating
1,200W
Power
15 litres (Dry) - 6 litres (Wet)
Container
Volume
Volume
2,700 litres/min
Air
73dB
Noise Level
355 x 355 x 500mm
Overall
L x W x H
9.5kg
Weight
WV380-2
Industrial
1,200W
15 litres (Dry) - 9 litres (Wet)
2,700 litres/min
66dB
355 x 355 x 510mm
8.6kg
NTD 2003S
Industrial
2 x 1,200W
80 litres
2,500mm
80 litres/sec
560 x 660 x 1145mm
30.5kg
Call free 0800 371822 Mobile friendly 03332 406406 Order online axminster.co.uk/extraction
Compressors 01.indd 127
127
27/11/2014 16:01
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement