DTS NICK NRG1200 CT Specifications

Add to my manuals
32 Pages

advertisement

DTS NICK NRG1200 CT Specifications | Manualzz

CT

D.T.S. Illuminazione s.r.l.

Via Fagnano Selve 10/12/14

Made in Italy

47843 Misano Adriatico (RN) ITALIA Tel +39 0541 611131 Fax +39 0541 611111 [email protected] http://www.dts-lighting.it

2

Le informazioni contenute in questo documento sono state attentamente redatte e controllate. Tuttavia non è assunta alcuna responsabilità per eventuali inesattezze.

Tutti i diritti sono riservati e questo documento non può essere copiato, fotocopiato, riprodotto per intero o in parte senza previo consenso scritto della D.T.S .

D.T.S. si riserva il diritto di apportare senza preavviso cambiamenti e modifiche estetiche , funzionali o di design a ciascun proprio prodotto. D.T.S non assume alcuna responsabilità sull’uso o sull’applicazione dei prodotti o dei circuiti descritti.

The information contained in this publication has been carefully prepared and checked. However, no responsibility will be taken for any errors. All rights are reserved and this document cannot be copied, photocopied or reproduced, in part or completely, without prior written consent from D.T.S.

D.T.S. reserves the right to make any aesthetic, functional or design modifications to any of its products without prior notice. D.T.S. assumes no responsibility for the use or application of the products or circuits described herein.

Les informations contenues dans le présent manuel ont été rédigées et contrôlées avec le plus grand soin. Nous déclinons toutefois toute responsabilité en cas d'éventuelles inexactitudes. Tous droits réservés. Ce document ne peut être copié, photocopié ou reproduit, dans sa totalité ou partiellement, sans le consentement préalable de D.T.S.

D.T.S. se réserve le droit d'apporter toutes modifications et améliorations esthétiques, fonctionnelles ou de design, sans préavis, à chacun de ses produits. D.T.S. décline toute responsabilité sur l'utilisation ou sur l'application des produits ou des circuits décrits.

Las informaciones contenidas en este documento han sido cuidadosamente redactadas y controladas. Con todo, no se asume ninguna responsabilidad por eventuales inexactitudes. Todos los derechos han sido reservados y este documento no puede ser copiado, fotocopiado o reproducido, total o parcialmente, sin previa autorización escrita de D.T.S.

D.T.S. se reserva el derecho a aportar sin previo aviso cambios y modificaciones de carácter estético, funcional o de diseño a cada producto suyo. D.T.S. no se asume responsabilidad de ningún tipo sobre la utilización o sobre la aplicación de los productos o de los circuitos descritos.

3

INDEX:

1-SYMBOLS 4

2- GENERAL WARNING 4

3- GENERAL WARRANTY CONDITION 4

4- TECHNICAL FEATURES 5

5- TECHNICAL SPECIFICATIONS 7

6- ACCESSORIES 7

7- IMPORTANT SAFETY INFORMATION 8

7.1 Fire prevention

7.2 Prevention of electric shock

7.3 Safety

7.4 Level of protection against the penetration of solid and liquid objects

8- VOLTAGE AND FREQUENCY 9

9- INSTALLATION 9

9.1 Safety cable

9.2 Protection against liquids

9.3 Movement

9.4 Risk of fire

9.5 Forced ventilation

9.6 Ambient temperature

10- MAINS CONNECTION 11

10.1 Protection

11- DMX SIGNAL CONNECTION 12

11.1 DMX Addresses

11.2 Selecting the DMX address

12- FIRMWARE UPDATING 13

13- DISPLAY FUNCTIONS 14

14- PERIODIC CLEANING 23

15- PERIODIC CONTROLS 23

16- DMX PROTOCOL 24

4

1- SYMBOLS

Graphic symbols used on this manual

THIS SYMBOL INDICATES A HOT SURFACE

THIS SYMBOL INDICATES ELECTRIC SHOCK

RISK

!

THIS SYMBOL INDICATES GENERAL RISK

F

THIS SYMBOL MEANS “DO NOT PLACE THE

UNIT ON INFLAMMABLE SURFACES”

0,5M THIS SYMBOL INDICATES THE MINIMUM

DISTANCE TO BE KEPT BETWEEN THE DEVICE

AND THE LIT OBJECT

2- GENERAL WARNING

Read the instruction contained in this user manual carefully, as they give important information regarding safety during installation , use and maintenance.

The device is not for domestic use and must be installed by a qualified electrician or experienced person.

Always disconnect the device from the mains before maintenance.

The device must always be equipped with an efficient ground connection.

3- GENERAL WARRANTY CONDITIONS

The unit is guaranteed for 36 months from the date of purchase against manufacturing material defects.

5

4- TECHNICAL FEATURES

Overview

NICK NRG 1200 CT is the most efficient LED moving head wash light ever produced.

The exceptional brightness / consumption ratio makes NICK NRG 1200 CT a truly

“green” fixture.

NICK NRG 1200 CT is equipped with 30 high-power Full White LEDs, 5.600 °K.

NICK NRG 1200 CT features three interchangeable lens fittings: Spot, Medium Flood and Wide Flood and ultra-fast silent Pan / Tilt.

Applications:

NICK NRG 1200 CT is suitable for top professional applications, such as tours and special events.

Product codes:

03.LDR008.FW12 NICK NRG 1200 CT Full White *Spot lenses *Black finish

03.LDR008.FW25

03.LDR008.FW45

NICK NRG 1200 CT Full White *Medium flood lenses *Black finish

NICK NRG 1200 CT Full White *Wide flood lenses *Black finish

03.LDR008.FW12WS NICK NRG 1200 CT Full White *Spot lenses

*With Wireless on board *Black finish

03.LDR008.FW25WS NICK NRG 1200 CT Full White *Medium flood lenses

*With Wireless on board *Black finish

03.LDR008.FW45WS NICK NRG 1200 CT Full White *Wide flood lenses

*With Wireless on board *Black finish

LED Technology

* 30 Full White LEDs (5.600 °K)

Optical group

* Three interchangeable lenses sets: Spot, Medium Flood and Wide Flood

* Uniform projection on surfaces

Interface / Control / Programming

* Multi-function OLED graphic colour display + 4 soft keys: control / management / monitoring of the main parameters

* Controlled via DMX 512 and RDM standard digital communication protocols

* Wireless ready; Ethernet ready

* Internal operating system updatable via D.T.S.

RED BOX interface via “D.T.S. firmware upgrade utility” program on windows based PC

6

DMX

20 DMX channels

Pan & Tilt

* 16-bit movement resolution

* Ultra-fast movement: Pan 540° (2 sec.); Tilt 270° (1,2 sec.)

* Selectable speed ranges

Power supply

* Electronic full-range AC 90-260 V 50 / 60 Hz

* Power consumption: 90 V – 3,7 A – 340 W ; 120 V – 2,83 A – 340 W ;

230 V

– 1,47 A - 340 W ; 260 V – 1,3 A – 340 W

Connectors

* DMX: 4 XLR connectors (3 poles In / Out; 5 poles In / Out) by Neutrik

* Power supply: POWERCON In / Out connectors by Neutrik

Operating ambient temperature

-10° / 40°

Weight

9,5 Kg

International certifications

Certification CE; LED Class: Class 2 LED product

7

5- TECHNICAL SPECIFICATIONS

Dimensions

Packaging Dimensions (LxWxH)

530 x 430 x 414 mm

Weight: 12 Kg

Unit Dimensions (LxWxH)

369x218x497 mm

Weight: 9,5 Kg

369 mm

6- ACCESSORIES

306 mm

As standard

• 1 x POWERCON male cable connector (cod. 0520P014)

• 1 x XLR 5 Pins Male cable connector by Neutrik (cod. 0508B066)

• 1 x XLR 5 Pins Female cable connector by Neutrik (cod. 0508B065)

• “C” Clamp GQUICK with “Fast Lock” connection 1/4 turn (cod. 0521A014)

• User’s manual

218 mm

Optional (on request)

Flight case

• Professional Flight case for 4 units; compartment for accessories, swivel wheels, cover with hinges with-stay, dishes on cover for piling, 8 handles (2 eachside)

(cod. 0521C051.1)

Wireless DMX receiver retrofit

• Wireless DMX Receiver Card with INDOOR IP20 omnidirectional 2dBi antenna included (cod.03.LA.126)

Clamps / safety wires

• “C” Clamp G60 black (max. load 50Kg) (cod. 0521A004)

• “C” Clamp G60 chrome (max. load. 50Kg) (cod. 0521A004.20)

• “C” Clamp GQUICK with “Fast Lock” connection 1/4 turn (max. load. 80Kg)

(cod. 0521A014)

• “C” Clamp G100 black / professional (max. load. 200Kg) (cod. 0521A015)

• Omega clamp with “Fast Lock” connection 1⁄4 turn 1 couple (2 pieces)

(Cod. 02K00467)

• Safety wire (3mm x 60 cm), ring spring catch, max. capacity load 60Kg (cod. 0521A010)

8

7- IMPORTANT SAFETY INFORMATION

7.1 Fire prevention:

-Never locate the fixture on any flammable surface.

-Minimum distance from flammable materials: 1 MT.

F

-Minimum distance from the closest illuminable surface: 0,5 MT.

0,5M

-Replace any blown or damaged fuses only with those of identical value.

Refer to the wiring diagram if there is any doubt.

-Connect the projector to mains power via a thermal magnetic circuit breaker.

7.2 Prevention of electric shock:

-High voltage is present inside the unit. Unplug the unit prior to performing any function which involves touching the inside of the moving head.

-The level of technology inherent in the NICK NRG 1200 CT requires the assistance of specialised personnel for all servicing.

Please refer to an authorised D.T.S. service centre.

-A good earth connection is essential for proper functioning of the projector.

-Never connect the unit without proper earth connection.

-The fixture should be located in places with a good air ventilation.

7.3 Safety:

!

-The projector should always be installed with bolts, clamps and other tools that are capable of supporting the weight of the unit.

-Always use a second safety cable to sustain the weight of the unit in case of the failure of the main fixing point.

-The external surface of the unit, at various points, may exceed 70°C. Never handle the unit until at least 10 minutes have elapsed since the projector was turned off.

-Never install the fixture in an enclosed area lacking sufficient air flow.

The ambient temperature should not exceed 40°C.

7.4 Level of protection against the penetration of solid and liquid objects:

!

-The projector is classified as an ordinary appliance and its protection level against the penetration of solid and liquid objects is IP 20.

9

8- VOLTAGE AND FREQUENCY

The NICK NRG 1200 CT can operate at 90-260 VOLT 50 or 60 Hz.

9- INSTALLATION

NICK NRG 1200 CT may be either floor or ceiling mounted.

For floor mounting installations, the NICK NRG 1200 CT is supplied with four rubber mounting feet on the base.

For ceiling mounted installations, we reccomend the use of appropriate clamps to fix the unit to the mounting surface.

The supporting structure from which the unit is hung should be capable of bearing the weight of the unit, as should any clamps used to hung it. The structure should also be sufficiently rigid so as not to move or shake whilst the NICK NRG 1200 CT is moving.

Four 1/4 turn Fast Locks connections placed in the base of the unit allow to hang the

NICK NRG 1200 CT by using the Fast Lock “C” clamps provided in the box.

9.1- Safety cable

!

We recommend the use of a safety cable or chain connected to the NICK NRG 1200

CT and to the suspension truss in order to avoid the fixture accidentally falling should the main fixing point fail.

Make sure that the iron cable or chain can bear the weight of the entire unit.

You may attach the safety chain/cord to the attachment point (A) located on the base of the fixture, as shown in the picture below.

SAFETY CHAIN/CORD

ATTACHMENT POINT

A

10

9.2 Protection against liquids

!

The projector contains electric and electronic components which should under no circumstances come into contact with oil, water or any other liquid.

The proper unit functioning would be compromised should this occur.

9.3- Movement

Ultra-fast movement: Pan 540° (2,0 sec.); Tilt 270° (1,2 sec.)

270°

!

WARNING

Do not place any object in the path of the projector’s movement

540°

9.4- Risk of fire

Each fixture produces heat and must be installed in a well-ventilated place.

The minimum recommended distance from flammable material is 1 MT.

Minimum distance from the object being illuminated is 0,5 MT.

0,5M

F

9.5- Forced ventilation

You will note, on inspection, that the unit features various air inlets and cooling fans.

These should, under no circumstances, be blocked or obstructed whilst the projector is in operation. Doing so could cause the fixture to seriously overheat thereby compromising its proper operation.

9.6- Ambient temperature

The projector should never be installed in places that lack a constant air flow.

The ambient temperature should NOT exceed 40°C.

11

10- MAINS CONNECTION

NICK NRG 1200 CT operate at 90-260 VOLT 50-60 Hz.

Prior to connecting the unit to your mains supply, ensure that the model in your possession correctly matches the mains supply available.

For connection purposes, ensure that your plug is capable of supporting 2 amps at 230V, or 5 amps at 90 V.

Strict adherence to regulatory norms is strongly recommended.

MAINS AC OUTPUT 90 – 260 V 50 / 60 Hz (16A Max)

MAX 10 NICK NRG 1200 UNITS @ 230V

MAX 5 NICK NRG 1200 UNITS @ 120V

MAINS AC INPUT 90 – 260 V 50 / 60 Hz

Wireless DMX Receiver Retrofit (Cod. 03.LA.126)

Cod. 03.LDR008.FW12WS

Cod. 03.LDR008.FW25WS

Cod. 03.LDR008.FW45WS

Cod. 03.LDR008.FW12

Cod. 03.LDR008.FW25

Cod. 03.LDR008.FW45

FUSE 5A T 5X20

The use of a thermal magnetic circuit breaker is recommended for each

NICK NRG 1200 CT.

12

11- DMX SIGNAL CONNECTION

The unit operates using the digital DMX 512 (1990) signal.

Connection between the mixer and the projector or between projectors must be carried out using a two pair screened ø 0.5 mm cable and a XLR 5 or 3 pins connector.

Ensure that the conductors do not touch each other.

Do not connect the cable ground to the XLR chassy.

The plug housing must be isolated. Connect the mixer signal to the DMX IN projector plug and connect it to the next projector by connecting the DMX OUT plug on the first projector to the DMX IN plug of the second one.

This way, all the projectors are cascade connected.

NB. If the display showing the DMX address flashes, then one of the following errors has occurred:

- DMX signal not present

- DMX address not valid

- DMX reception problem

CONTROLLER

S TA N D A R D

D M X 5 1 2

5

4

1

2

1=GND

2=DATA-

3=DATA+

3

DMX OUT DMX IN DMX OUT DMX IN DMX OUT DMX IN DMX OUT DMX IN DMX OUT

For Installations where long distance DMX cable connections are needed, we suggest to use a DMX terminator.

The DMX terminator is a male XLR 3-5 pins connector with a 120 ohm resistor between pin 2 and 3.

The DMX terminator must be plugged into the last unit (DMX out panel connector) of the DMX line.

5 1

4

3

2

OUT

PLACE A 120 OHM RESISTOR BETWEEN PIN 2

AND 3 OF A MALE XRL CONNECTOR AND PLUG IT

INTO THE DMX OUT PANEL CONNECTOR OF THE

LAST UNIT CONNECTED TO THE DMX LINE

PIN 3

120 ohm

PIN 2

13

11.1-DMX Addresses

NICK NRG 1200 CT can be controlled with 20 DMX channels.

In order to use the unit in 20 channels, set the following addresses on the mixer:

Projector 1 A001

Projector 2 A021

Projector 3 A041

….. A…. projector 6 A101

If you want to select the next projector, just add “20”

11.2-Selecting the DMX address

1) Press the UP-DOWN key until you reach the required DMX channel. The numbers on the display will start to flash (but the new DMX address hasn't yet been set).

2) Press ENTER to confirm your selection. The numbers on the display will stop flashing and the projector is now setted to the new DMX address.

TRICKS:

if you keep pushed the UP or DOWN keys, the channels are calculated more quickly and you get a faster selection.

12- FIRMWARE UPDATING

Warning:

This procedure require a base knowledge of computer applications and Windows

Hyperterminal program. Please refer to an authorised D.T.S. service centre.

To update the software version of the NICK NRG 1200 you need:

D.T.S. RED BOX interface (D.T.S. Code: 03.LA.008).

USB-DMX Driver for the D.T.S. RED BOX interface.

D.T.S. Firmware upgrade utility program.

(The driver and the installation procedure are available in our web site www.dts-lighting.it)

Updating the software version.

Please follow the procedure below to perform the update:

1. Install the D.T.S. RED BOX USB-DMX driver on the PC you will use to update the unit software.

!

2. Connect the D.T.S. RED BOX interface to the PC by using a USB cable.

3. Connect the D.T.S. RED BOX interface to the fixture by using a DMX cable.

4. Download the new software version into the unit by using D.T.S. Firmware upgrade utility program.

14

13- DISPLAY FUNCTIONS

DISPLAY 2dBi IP20 omnid.

antenna

WIRELESS DMX

RECEIVER

RETROFIT

03.LA.126

MENU

ENTER

DMX OUT

DMX IN

DMX IN

DMX OUT

UP

DOWN

DMX

IN

DMX

OUT

Cod. 03.LDR008.FW12WS

Cod. 03.LDR008.FW25WS

Cod. 03.LDR008.FW45WS

MAINS AC OUTPUT

90-260V 50 / 60 Hz

(16A Max)

03.LDR008.FW12

Cod. 03.LDR008.FW12

Cod. 03.LDR008.FW25

Cod. 03.LDR008.FW45

03.LDR008.F25

MAINS AC INPUT

90-260V 50 / 60Hz

DISPLAY FUNCTIONS

The NICK NRG 1200 CT display panel shows all the available functions . Using these functions, it is possible to change some of the parameters and add some functions.

Changing the D.T.S. setting can vary the functions of the unit so that it does not respond to the DMX 512 used to control it. Carefully follow the instructions below before carrying out any variations or selections.

NOTE: the symbol shows which key has to be pushed to obtain the desired function.

15

13- DISPLAY FUNCTIONS

Software version 1.10

Menu Up-Down

Display

ENTER Up-Down

DISPLAY

POSITION

Display Position:

AA

Reverses display's reading depending on the mounting position

(on the ground or suspended).

MENU ENTER DOWN UP

Display Position

ON THE GROUND (Default)

SUSPENDED

DISPLAY

Display Standby

STANDBY

OFF disabled (Default)

ON = Display goes OFF after 5 seconds

ENTER

ENTER

MENU ENTER DOWN UP

Menu Up-Down ENTER Up-Down

DMX MODE

20 ch DMX Mode

DMX Mode

20 channels

DMX MODE / MACRO

ENTER

MENU ENTER DOWN UP

MACRO

(Colour MACROS active only on NICK

NRG 1200 FULLCOLOUR,

NICK NRG 1200 CT will show only different white light intensity )

Macro Mode:

STD = Standard (Default)

EXT = Extended; enable rainbow effects on Macro channel (DMX ch 16)

DMX SET

MENU ENTER DOWN UP

MACRO (Active only on NICK NRG

1200 FULLCOLOUR

NICK NRG 1200 CT will show only different white light intensity)

STD = Standard mode enabled

(Default)

EXT = Extended; enable rainbow effects on Macro channel

(DMX ch 16)

16

13- DISPLAY FUNCTIONS

NICK NRG 1200 FULLCOLOUR:

RGBA MINIMUM VALUES

This menu allow to select the minimum levels for Red, Green,

Blue and Amber/White

NICK NRG 1200 CT:

4 x WHITE MINIMUM VALUES

This menu allow to select the minimum levels for Red = White 1,

Green = White 2, Blue = White 3 and

Amber/White = White 4

NICK NRG 1200 FULLCOLOUR:

MENU ENTER DOWN UP

MENU ENTER DOWN UP

NICK NRG 1200

FULLCOLOUR / CT:

RED / WHITE 1

Min default = 0

RED / WHITE 1

Max default = 100

NICK NRG 1200

FULLCOLOUR / CT:

GREEN / WHITE 2

Min default = 0

GREEN / WHITE 2

Max default = 100

This menu allow to select the NICK NRG 1200 maximum levels for Red, Green, FULLCOLOUR / CT:

Blue and Amber/White

BLUE / WHITE 3

These settings have priority Min default = 0 on Master Dimmer (DMX channel 9) BLUE / WHITE 3

Max default = 100

NICK NRG 1200 CT:

MENU ENTER DOWN UP

4 x WHITE MAXIMUM VALUES

DMX SET maximum levels for Red = White 1,

LED

NICK NRG 1200

FULLCOLOUR / CT:

Green = White 2, Blue = White 3 and

AMBER / WHITE 4

Amber/White = White 4

Min default = 0

These settings have priority

AMBER / WHITE 4 on Master Dimmer (DMX channel 9)

Max default = 100

MENU ENTER DOWN UP

SMOOTH VALUE

This menu allow to select the value of the delay (in milliseconds) for

RGBA (NICK NRG 1200 FULLCOLOUR) or WHITE (NICK NRG 1200 CT) and

DMX SET

DMX MODE

SMOOTH

Range = Off – 20

Default = 4

Dimmer channels reaction to DMX or program variation.

4

4 = 25 ms delay (Fast response)

MENU ENTER DOWN UP

20 = 250 ms delay (Slow response)

ENTER

17

13- DISPLAY FUNCTIONS between Linear current output or Quadratic current output for LEDs

Default = Quadratic

QUAD

MENU ENTER DOWN UP

GAMMA CORRECTION

Linear = Linear current output

Quadratic = Linear light output

(default)

OUTPUT FREQUENCY

DMX SET the PWM frequency value (Hz) in order to reduce flickering in

DMX MODE the process of your camera

OUTPUT FREQ.

recordings

MENU ENTER DOWN UP

OUTPUT FREQUENCY

Range = 610 Hz – 10KHz

Default = 610 Hz t

BOOST DRIVING

DMX SET

BOOST

BOOST

With BOOST active, the

LEDs current is set to

500 Ma (30% more gain)

Default = Enabled

MENU ENTER DOWN UP

AUTO

AUTOMATIC MODE

Automatic demo games

DMX MODE

20 ch without DMX controller

(Colour MACROS active only on

MENU ENTER DOWN UP

NICK NRG 1200 FULLCOLOUR,

NICK NRG 1200 CT will show only different white light intensity )

STEP 01/16

Chase with 16 steps previously created in REC MODE

Speed time, Wait time, Dimmer, Pan and Tilt values selectable by user.

PERSONAL COLOURS

RGBA, Dimmer, Shutter, Pan and Tilt values selectable by user.

RAINBOW

Rainbow colours effect.

Speed time, Dimmer, Shutter, Pan and Tilt values selectable by user.

MENU ENTER DOWN UP

MENU ENTER DOWN UP

MENU ENTER DOWN UP

ENTER

By setting all the units connected to the MASTER to DMX address 1, them will be synchronized with the

Master unit following the chase selected on it including TIME, WAIT,

Pan and Tilt position of the MASTER unit.

ENTER

18

13- DISPLAY FUNCTIONS

DMX SET

Sixteen Colour Macros as o n “MACRO” channel.

Dimmer, Shutter, Pan and Tilt it, values selectable by user.

WHITE MACROS (Active only on

MENU ENTER DOWN UP

By setting all the units connected to the MASTER to DMX address 1, them will be synchronized with the

Master unit following the chase selected on it including TIME, WAIT,

Pan and Tilt position of the

MASTER unit.

ENTER

NICK NRG 1200 FULLCOLOUR)

Sixteen macros for White colour (active only on NICK NRG

1200 FULLCOLOUR);

White Macros for NICK

NRG 1200 CT: Different white light

Intensity.

Dimmer, Shutter, Pan and Tilt values selectable by user.

MENU ENTER DOWN UP

Menu Up-Down

SLAVE

ENTER Up-Down

DMX SET

DMX MODE

20 ch

The SLAVE unit receive DMX signal from the MASTER unit.

By setting all the SLAVE units

DMX address 1, them will be

ENTER unit following the chase selected on it, but running their own Pan and Tilt position. from MASTER unit (set in

AUTO MODE) in order to ran the units in SLAVE mode.

By setting all the SLAVE units

DMX SET connected to the MASTER, to

DMX address 1, them will be synchronized with the Master unit following the chase selected on it, but running their own Pan and Tilt position.

MENU ENTER DOWN UP

MENU ENTER DOWN UP

19

13- DISPLAY FUNCTIONS

DMX SET

WIRELESS DMX

Wieless DMX enabled / disabled.

By activating WDMX MODE, it will be possible to control NICK NRG

1200 CT via D.T.S. ANTENNA

Wireless DMX Transmitter (cod.

03.E1271).

Wireless DMX Receiver Kit

(Cod. 03.LA.126) on NICK NRG

MENU ENTER DOWN UP

WIRELESS DMX SYSTEM

DISABLED (Default)

WIRELESS DMX SYSTEM

ENABLED

ENTER

ENTER

MENU ENTER DOWN UP

UNLINK = LOG OUT

ENTER

MENU ENTER DOWN UP

Logging on NICK NRG 1200 CT (WIRELESS DMX must be enabled on the unit).

To log on the NICK NRG 1200 CT in the WIRELESS system simply press and quickly release the function button on the transmitter .

The transmitter will start flashing rapidly red/green scanning for new free receivers / NICK NRG 1200

CT units. When a NICK NRG 1200 CT logs on to the transmitter the LINK green light on transmitter starts to flash rapidly.

After approximately 10 seconds the transmitter will jump back to normal mode and continue transmitting data. The NICK NRG 1200 CT now try to synchronize to the transmitter.

When synchronized to the transmitter, 2 different modes are possible:

1. Antenna transmitter has detected and transmits a DMX signal, in this mode a solid green light is seen on the transmitter and solid display is seen on NICK NRG 1200 CT.

2. No DMX signal connected, the Antenna transmitter will flash red/green; display blinking on NICK

NRG 1200 CT.

To log off NICK NRG 1200 CT from a transmitter simply select UNLINK function under WIRELESS

DMX MENU and press ENTER.

When NICK NRG 1200 CT is logged off the display is blinking, meaning its available for log in on a new transmitter.

Logging out a NICK NRG 1200 CT.

Select UNLINK function under WIRELESS DMX MENU and press ENTER.

When NICK NRG 1200 CT is logged off the display is blinking, meaning its available for log in on a new transmitter.

Logging out all NICK NRG 1200 CT linked to a transmitter.

Press and hold the function button of the transmitter for about 3 seconds. When the display is blinking on NICK NRG 1200 CT, it mean that the units are logged out.

Transmitter, Status LED.

Flashing red/green, no dmx connected.

Solid green, dmx signal detected and transmitted.

Fast flashing red/green, log in mode (every free NICK NRG 1200 CT unit, not logged in to any other transmitter, will be logged on)

NICK NRG 1200 CT Status.

Display blinking, not logged on to a transmitter (free).

Solid display, logged on to a transmitter and receiving dmx data.

20

13- DISPLAY FUNCTIONS

EMERGENCY

Menu Up-Down ENTER Up-Down

DMX SET

EMERGENCY

Emergency operating mode.

By setting Emergency mode, it will be possible to select one of the

16 pre-programmed WHITE cues

(active only on NICK NRG 1200

FULLCOLOUR;

NICK NRG 1200 CT will show only different white light intensity) that

will then ran if DMX signal is missing

MENU ENTER DOWN UP

Useful for Emergency EXIT illumination on public areas. MENU ENTER DOWN UP

Dimmer level and Pan&Tilt values selectable by user.

1

MENU ENTER DOWN UP

MENU ENTER DOWN UP

128

MENU ENTER DOWN UP

128

MENU ENTER DOWN UP

EMERGENCY

Disabled = Default

EMERGENCY

Enabled

WHITE (1-16)

Default = WHITE 1

DIMMER

Default = 255

PAN

Default = 128

TILT

Default = 128

ENTER

21

13- DISPLAY FUNCTIONS

DEFAULT SET

Menu Up-Down ENTER

DEFAULT SETTINGS

Up-Down

To restore default settings

ENTER

TEMPERATURE

Unit temperature

TIME

Up-Down ENTER Up-Down

LIFE TIME

This menu show the total UNIT life time and the RGBA (NICK NRG

1200 FULLCOLOUR) or the

R = WHITE 1, G = WHITE 2,

B = WHITE 3, A = WHITE 4

(NICK NRG 1200 CT) life time

DMX MODE

20 ch

MENU ENTER DOWN UP

SURE?

20 ch

MENU ENTER DOWN UP

DMX MODE

028.7

MENU ENTER DOWN UP

MENU ENTER DOWN UP

MENU ENTER DOWN UP

MENU ENTER DOWN UP

MENU ENTER DOWN UP

ENTER

ENTER

MENU ENTER DOWN UP

22

13- DISPLAY FUNCTIONS

PAN INVERSION

Default = NORM

ENTER

PAN INVERSION / TILT INVERSION /

PAN SPEED / TILT SPEED /

FAN MAX SPEED / RESET BY DMX /

MOTORS FIRMWARE UPGRADE. MENU ENTER DOWN UP

This menu allows to set the Pan

TILT INVERSION

Default = NORM

TILT INVERTION

This menu allows to set the Tilt movement. Normal or Reversed.

MENU ENTER DOWN UP

SYSTEM

Pan Speed control (1-8)

PAN SPEED

TILT SPEED

Tilt Speed control (1-8)

20 ch

FAN MAX SPEED

This menu’ allow to select the internal fans speed.

PAN SPEED CONTROL

Default = 4

TILT SPEED CONTROL

Default = 4 disable the Motors reset control

4

MOTORS FIRMWARE UPGRADE

This menu’ allow to upgrade the

MENU ENTER DOWN UP firmware for Pan&Tilt circuit boards.

FAN MAX SPEED

50% - 100%

Default = 100%

FAN MAX SPEED

MENU ENTER DOWN UP

RESET BY DMX

Enable: Motors reset enabled via DMX

(Default)

Disabled: Motors reset disabled via DMX

Now: Instant motors reset.

MENU ENTER DOWN UP

MOTORS FIRMWARE UPGRADE

Pan&Tilt circuit boards firmware upgrade.

DMX MODE

20 ch

MENU ENTER DOWN UP

23

13- DISPLAY FUNCTIONS

SOFTWARE

Menu Up-Down ENTER Up-Down

DMX SET

SOFTWARE

LEDs circuit board software,

MOTORS circuit boards software

(Pan&Tilt)

20 ch v1.10 Jun 13 2012

MENU ENTER DOWN UP

LEDs CIRCUIT BOARD

SOFTWARE

ENTER

Motors

MOTORS CIRCUIT BOARDS

SOFTWARE

(PAN&TILT)

14- PERIODIC CLEANING

MENU ENTER DOWN UP

Front lenses Glass

The dust can reduce the luminous output substantially.

Regularly clean the front lenses glass using a soft cotton cloth, dampened with a specialist glasses cleaning solution.

Fans and air passages

The fans and air passages must be cleaned approximately every 6 weeks.

This periodic cleaning will depend of course, on the conditions in which the projector is operating.

Suitable instruments for performing this type of maintenance are a brush and a common vacuum cleaner or an air compressor.

If necessary, clean the fans and air passages more frequently.

15- PERIODIC CONTROLS !

Mechanical parts

Periodically check all mechanical parts and the gaskets, replacing them if necessary.

Electrical components

Check all electrical components for correct earthing and proper attachment of all connectors, refastening if necessary.

Attention: Disconnect mains power prior to removing the projector housing.

Fuse replacement

Locate the fuse, which protect the electronics, in the base of the

NICK NRG 1200 CT. Using a multimeter, test the condition of the fuse, replacing it with one of equivalent type if necessary.

Attention: Disconnect mains power prior to removing the projector housing.

24

16- DMX PROTOCOL

20 CHANNELS MODE

1

2

3

4

5

6

PAN msb 540°

PAN Isb

TILT msb 270°

TILT Isb

SPEED MOVEMENT

NO FUNCTION

7 NO FUNCTION

8 SHUTTER

9 DIMMER

10 RED = WHITE 1

11 GREEN = WHITE 2

12 BLUE = WHITE 3

13 WHITE = WHITE 4

14 WHITE PRE-PROGRAMMED (Not Active)

15 CTC

16 MACRO (Not Active)

17 FUNCTION (Recall, Create and Store the Custom white)

18 NO FUNCTION

19 NO FUNCTION

20 RESET

DMX CHANNEL 1 Parameter: PAN msb

DMX CHANNEL 2 Parameter: PAN lsb

DMX CHANNEL

DMX CHANNEL

DMX CHANNEL

DMX range

Value

000-010

011-025

026-127

3

4

5

Parameter: TILT msb

Parameter: TILT lsb

Parameter: SPEED MOVEMENT

Mid Point DMX value

Move Range

(degrees)

Mode Option

128-247

248-255

Function

Standard

Fast movement

Vector mode from fast to slow

Variable time reaction to

DMX signal (fast

to slow)

Slow reaction time to DMX signal

25

DMX CHANNEL 6 Parameter: NO FUNCTION

DMX range

Value

000-255

DMX CHANNEL

Mid Point

DMX value

7

Move Range

(degrees)

Mode

Parameter: NO FUNCTION

DMX range

Value

000-255

DMX CHANNEL

Mid Point

DMX value

8

Move Range

(degrees)

Mode

Parameter: SHUTTER

DMX range

Value

000-009

010-019

020-029

030-119

120-149

150-179

180-204

Mid Point

DMX value

Move Range

(degrees)

Mode

205-229

230-255

DMX CHANNEL

DMX range

Value

000-007

008-255

9 Parameter: DIMMER

Mid Point DMX value

Move Range

(degrees)

DMX CHANNEL

DMX range

Value

000-255

10 Parameter: RED = WHITE 1

Mid Point DMX value

Move Range

(degrees)

Option

Option

Option

Mode

Mode

NO FUNCTION

NO FUNCTION

Black-out

Open

Black-out

Strobe (from 3.27 s to 30 ms)

Pulse up (from 42.6 s to 120 ms)

Pulse down (from 42.6 s to 120 ms)

Random strobe (Dimmer, Red,

Green, Blue, Amber channels active)

Full independent Random Strobe

(Dimmer, Red, Green, Blue, Amber channels disabled)

Open

Option

Option

Function

Function

Function

Function

Black-out

Proportional dimmer

Function

Proportional colour

26

DMX CHANNEL

DMX range

Value

000-255

11 Parameter: GREEN = WHITE 2

Mid Point DMX value

Move Range

(degrees)

Mode Option Function

Proportional colour

DMX CHANNEL

DMX range

Value

000-255

12 Parameter: BLUE = WHITE 3

Mid Point DMX value

Move Range

(degrees)

Mode Option Function

Proportional colour

DMX CHANNEL

DMX range

Value

000-255

13 Parameter: WHITE = WHITE 4

Mid Point DMX value

Move Range

(degrees)

Mode Option Function

15 Parameter: CTC (Colour Temperature Correction)

Proportional colour

DMX CHANNEL

NICK NRG 1200 CT will show only different white light intensity

DMX range

Value

000-055

056-105

106-155

156-205

Mid Point DMX value

23

80

130

180

Move Range

(degrees)

Mode

206-255

14 Parameter: WHITE PRE-PROGRAMMED (Not Active on NICK NRG 1200 CT)

230

Option Function

No Function

Full (Red-Green-

Blue at Full)

White DTS

Custom White

Create (RGB levels selectable by DMX)

White CTC

(Channel 15

CTC enabled)

DMX CHANNEL

NICK NRG 1200 CT will show only different white light intensity

DMX range Mid Point DMX Move Range Mode Option Function

Value value (degrees)

IF CHANNEL 14 WHITE PREPROGRAMMED = WHITE CTC (DMX range value 206 – 255)

Linear control

000-255 temperature correction.

NICK NRG 1200

FULLCOLOR:

0 = 2700°K /

255 = 8000°K.

NICK NRG 1200 CT

FULLWHITE: different white light intensity

27

DMX CHANNEL 16 Parameter : MACRO (NICK NRG 1200 CT WILL SHOW ONLY DIFFERENT WHITE LIGHT INTENSITY )

IF: DMX SET MACRO STD (Please refer to page 15 for details)

000-014

015-029

No Function

Macro 1

030-044

045-059

060-074

075-089

090-104

105-119

Macro 2

Macro 3

Macro 4

Macro 5

Macro 6

Macro 7

120-134

135-149

150-164

165-179

180-194

195-209

210-225

226-239

240-255

DMX CHANNEL 16 Parameter:

Macro 8

Macro 9

Macro 10

Macro 11

Macro 12

Macro 13

Macro 14

Macro 15

Macro 16

MACRO (NICK NRG 1200 CT WILL SHOW ONLY DIFFERENT WHITE LIGHT INTENSITY )

IF: DMX SET MACRO EXT (Please refer to page 15 for details)

000-014

015-024

No Function

Macro 1

025-034

035-044

045-054

055-064

Macro 2

Macro 3

Macro 4

Macro 5

065-074

075-084

085-094

095-104

105-114

Macro 6

Macro 7

Macro 8

Macro 9

Macro 10

115-124

125-134

135-144

145-154

155-164

165-174

175-184

185-194

195-204

205-214

215-224

225-234

235-244

245-255

Macro 11

Macro 12

Macro 13

Macro 14

Macro 15

Macro 16

Rainbow Speed 1 (6 Sec.)

Rainbow Speed 2 (15 Sec.)

Rainbow Speed 3 (30 Sec.)

Rainbow Speed 4 (45 Sec.)

Rainbow Speed 5 (60 Sec.)

Rainbow Speed 6 (120 Sec.)

Rainbow Speed 7 (150 Sec.)

Rainbow Speed 8 (180 Sec.)

28

DMX CHANNEL

DMX range

Value

000-079

080-160

161-255

17 Parameter: FUNCTIONS (Recall, Create and Store the Custom white)

Mid Point DMX Move Range Mode Option value (degrees)

IF CHANNEL 14 WHITE PREPROGRAMMED = DMX range value 156 – 205)

Function

Custom White

Recall

Custom White

Create (Enable

Custom White

Creation)

Custom White

Store (Store the

Custom White created)

DMX CHANNEL

DMX range

Value

000-255

DMX CHANNEL

DMX range

Value

000-255

DMX CHANNEL

DMX range

Value

000-015

016-255

18 Parameter: NO FUNCTION

Mid Point DMX value

19 Parameter: NO FUNCTION

Mid Point DMX value

20 Parameter: RESET

Mid Point DMX value

Move Range

(degrees)

Move Range

(degrees)

Move Range

(degrees)

Mode

Mode

Mode

Option

Option

Option

Function

NO FUNCTION

Function

NO FUNCTION

Function

No Effect

Total Reset

(activation after

3 sec.)

NOTES

29

NOTES

30

NOTES

31

32

The information contained in this publication has been carefully prepared and checked. However, no responsibility will be taken for any errors. All rights are reserved and this document cannot be copied, photocopied or reproduced, in part or completely, without prior written consent from D.T.S.

D.T.S. reserves the right to make any aesthetic, functional or design modifications to any of its products without prior notice. D.T.S. assumes no responsibility for the use or application of the products or circuits described herein.

MADE IN ITALY

ISO 9001:2008

D.T.S. quality system is certified to the

ISO 9001:2008 standard

D.T.S. products are designed and manufactured at the D.T.S. plants in italy

*0517I195.CT*

0517I195.CT

D.T.S. Illuminazione s.r.l. – Via Fagnano Selve 10-12-14 47843

Misano Adriatico (RN) Italia

Tel.: +39 0541 611131. Fax + 39 0541 611111

[email protected]

www.dts-lighting.it

advertisement

Was this manual useful for you? Yes No
Thank you for your participation!

* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project

Related manuals

Download PDF

advertisement

Languages