RT S1R Slip-On (2014
Installation Instructions
1.
Make sure the bike is completely cool before starting the
installation. Make sure the bikes parking brake is set.
2.
If applicable, remove right side saddlebag for ease of install.
3.
Remove OEM muffler joint clamp.
Can-Am
SPYDER RT
S1R Slip-On
Part # 005-3930405-S1
4.
5.
7.
Apply a thin layer of anti-seize to slip tube and attach to
muffler with supplied hook springs.
8.
Slide clamp over S1R muffler.
9.
Attach TBR exhaust assembly using OEM joint clamp and
supplied bolt, nut, and washer. Make adjustments to get
muffler alignment straight. Then tighten muffler clamp and
joint clamp.
Remove OEM muffler mounting bolt.
Remove OEM muffler assembly.
IMPORTANT - PLEASE READ CAREFULLY
Two Brothers Racing products are intended for closed course competition
purposes only.
We recommend that this performance part be installed by a qualified
motorcycle technician. If you have any doubts as to your ability to install
this performance part, please consult with your local motorcycle dealer. Read
all instructions first before starting installation. Make sure the motorcycle
and exhaust system are completely cool before starting the installation. Be
sure to save all stock components for possible use later.
**This product has not been tested with all available accessories and some
items may cause excessive heat. Excessive heat may cause damage to your
vehicle. Two Brothers Racing will not be responsible for damaged parts.
6.
Install supplied TBR muffler hanger bracket using the OEM
bolt, nut, and washer.
Installation Instructions
Care & Cleaning
Care & Cleaning
Keep system free of dirt and moisture. Store in a cool, dry place. Make sure vehicle is
completely cool before maintenance.
Stainless Header System: Polished stainless steel pipes will turn a light golden hue
after a few heat cycles, this is a normal characteristic of high quality stainless steel.
Clean using a mild water based spray cleaner. Always apply cleaner or polish with a
soft, clean cloth.
Titanium Header System: Polished titanium pipes will experience color shift ranging
from deep blue/purple through amber after a few heat cycles. This is a normal
characteristic of high quality titanium. Clean using a mild water based spray cleaner.
Always apply cleaner or polish with a soft, clean cloth.
Can-Am
SPYDER RT
S1R Slip-On
Part # 005-3930405-S1
10. Double check all your work.
11. Before you run the bike, clean off all fingerprints and dirt, as
any oily residue will etch the metal and become somewhat
permanent when the system gets hot. Run the bike and enjoy.
It is normal for some white smoke to appear the first time you
start the bike. This is packing/manufacturing oil from inside
the pipe burning off. Check for gaps or leaks. If you find a
leak, a little high temperature silicon sealant should fix it. After
50 to 100 miles, recheck all fasteners for tightness.
Polished Aluminum Canisters: Use an aluminum or mag wheel polish to restore the
bright finish to factory spec.
Brushed Aluminum Canisters: Clean using a mild water based spray cleaner. Always
apply cleaner or polish with a soft, clean cloth.
Carbon Fiber Canisters: Clean using a mild water based spray cleaner. Always apply
cleaner or polish with a soft, clean cloth. Always make sure the fiberglass packing inside
is in good condition and not burned out, as exhaust heat inside an empty canister will
deteriorate the carbon fiber sleeve.
TBR sells repack kits (Road - #005-10038, Offroad - #005-10038MX) that include
everything you need to easily do it yourself.
Titanium Mufflers: For cleaning use a mild water based spray cleaner. Always apply
cleaner or polish with a soft, clean cloth. Always make sure the fiberglass packing inside
is in good condition and not burned out, as exhaust heat inside an empty canister will
deteriorate the carbon fiber sleeve.
TBR sells repack kits (Road - #005-10038, Offroad - #005-10038MX) that include
everything you need to easily do it yourself.
Repack all road canisters every 3,000 miles. Part #005-10038
Repack all offroad canisters after every 10 hours of use. Part #005-10038MX
NEVER dyno test your bike with carbon fiber or titanium canisters installed - the
intense heat and lack of cooling air can quickly burn through the canister material. Two
Brothers Racing does not provide a warranty for burned canisters.
Warranty
Two Brothers Racing products are intended for closed course competition purposes
only, and therefore are sold “as is” without warranty. Two Brothers Racing specifically
disclaims any warranties of merchantability or fitness for a particular purpose and
disclaims all responsibility for consequential and incidental damages or any other losses
arising from the use of these products or parts.
Parts List
Qty.
Description
Part Number
1
1
1
2
1
1
1
1
1
S1R Muffler
Slip-On Tube Bracket
Springs
8mm Flange Nut
8mm Washer
8x20mm Socket Head Cap Screw
Anti-Seize
Spring Tool
005-3930405-S1
005-39304S
005-359-B
005-S45
005-FN8
005-WF8
005-SH820
031-P09175
005-SP
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement