Viking VE-RMB Retro-Fit Mounting Bracket Technical Information

Viking VE-RMB Retro-Fit Mounting Bracket Technical Information
TECHNICAL
Practice
TELECOM SOLUTIONS
Practice
FOR THE
VE-RMB
Retro-Fit Mounting
Bracket
2 1 S T C E N T U RY
July 9, 2004
Mount Your Viking Junction Box
into an Existing Wall
The VE-RMB attaches to the junction box supplied with Viking doorboxes and allows installation into existing walls. The bracket is screwed
to the back of the junction box and provides a
means of mounting even when no wall stud or
support beam is accessible.
Simply drill a 1/4 inch hole in the back of the
junction box, and use the screw provided to
attach the bracket to the box.
After cutting a hole in the wall, slip the assembly through the hole and tighten
the screw. No need to find a wall stud or support beam!
Phone...715.386.8861
Features
Applications
Use with the junction boxes included with these
Viking products:
Fax Back #
Model
Description
E-10/EWP
Speaker Phone
210
E-30/EWP
Stainless Speaker Phone
212
• Handles a wide range of wall thicknesses
E-1600-20A/EWP
Emergency Phone
215
E-1600-55A
Emergency Phone
215
• Holds the junction box in the wall until the
doorbox can be installed
W-1000/EWP
Doorbox
170
W-3000/EWP
Stainless Doorbox
180
• Allows mounting Viking junction boxes into
an existing wall
• Made from rust-resistant galvanized steel
Made in the U.S.A.
• Mounting screw included
• Made in the U.S.A.
Specifications
w w w. v i k i n g e l e c t r o n i c s . c o m
Shipping Weight: 0.09 kg (0.2 lbs)
Environmental: 0° C to 32° C (32° F to 90° F) with 5% to 95%
non-condensing humidity
Junction Box Requirement: Use with the Viking 102mm x
102mm x 51mm (4” x 4” x 2”) plastic box, part number: 259576
Minimum Wall Cavity Depth: 83mm (3.25”)
Minimum Wall Thickness: 3.2mm (0.125”)
Maximum Wall Thickness: 19mm (0.75”)
[email protected]
IF YOU HAVE A PROBLEM WITH A VIKING PRODUCT, PLEASE CONTACT: VIKING TECHNICAL SUPPORT AT (715) 386-8666
Our Technical Support Department is available for assistance Monday 8am - 4pm and Tuesday through Friday 8am - 5pm central time. So that we can give you better service, before you call please:
1. Know the model number, the serial number and what software version you have (see serial label).
2. Have your Technical Practice in front of you.
3. It is best if you are on site.
RETURNING PRODUCT FOR REPAIR
RETURNING PRODUCT FOR EXCHANGE
The following procedure is for equipment that needs repair:
1. Customer must contact Viking's Technical Support Department at 715-386-8666 to obtain a Return Authorization (RA) number. The customer
MUST have a complete description of the problem, with all pertinent information regarding the defect, such as options set, conditions, symptoms, methods to duplicate problem, frequency of failure, etc.
2. Packing: Return equipment in original box or in proper packing so that damage will not occur while in transit. Static sensitive equipment such
as a circuit board should be in an anti-static bag, sandwiched between foam and individually boxed. All equipment should be wrapped to avoid
packing material lodging in or sticking to the equipment. Include ALL parts of the equipment. C.O.D. or freight collect shipments cannot be
accepted. Ship cartons prepaid to: Viking Electronics, 1531 Industrial Street, Hudson, WI 54016
3. Return shipping address: Be sure to include your return shipping address inside the box. We cannot ship to a PO Box.
4. RA number on carton: In large printing, write the R.A. number on the outside of each carton being returned.
The following procedure is for equipment that has failed out-of-box (within 10 days of purchase):
1. Customer must contact Viking’s Technical Support at 715-386-8666 to determine possible causes for the problem. The customer MUST be able
to step through recommended tests for diagnosis.
2. If the Technical Support Product Specialist determines that the equipment is defective based on the customer's input and troubleshooting, a
Return Authorization (R.A.) number will be issued. This number is valid for fourteen (14) calendar days from the date of issue.
3. After obtaining the R.A. number, return the approved equipment to your distributor, referencing the R.A. number. Your distributor will then
replace the product over the counter at no charge. The distributor will then return the product to Viking using the same R.A. number.
4. The distributor will NOT exchange this product without first obtaining the R.A. number from you. If you haven't followed the steps
listed in 1, 2 and 3, be aware that you will have to pay a restocking charge.
WARRANTY
Viking warrants its products to be free from defects in the workmanship or materials, under normal use and service, for a period of one year from the date of purchase from any authorized Viking distributor or 18 months from the date manufactured, which ever is greater. If at any time during the warranty period, the product is deemed defective or malfunctions, return the product to Viking Electronics, Inc., 1531 Industrial Street, Hudson, WI., 54016. Customer must contact Viking's Technical Support Department at 715-386-8666 to obtain a Return Authorization (R.A.) number.
This warranty does not cover any damage to the product due to lightning, over voltage, under voltage, accident, misuse, abuse, negligence or any damage caused by use of the product by the purchaser or others.
Vikings sole responsibility shall be to repair or replace (at Viking's option) the material within the terms stated above. VIKING SHALL NOT BE LIABLE FOR ANY LOSS OR DAMAGE OF ANY KIND INCLUDING INCIDENTAL OR CONSEQUENTIAL DAMAGES RESULTING DIRECTLY OR
INDIRECTLY FROM ANY BREACH OF ANY WARRANTY EXPRESSED OR IMPLIED, OR FOR ANY OTHER FAILURE OF THIS PRODUCT. Some states do not allow the exclusion or limitation of incidental or consequential damages, so this limitation may not apply to you.
THIS WARRANTY IS IN LIEU OF ALL OTHER WARRANTIES, EXPRESSED OR IMPLIED, INCLUDING THE WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, WHICH ARE HEREBY EXCLUDED BEYOND THE ONE YEAR DURATION OF THIS
WARRANTY. Some states do not allow limitation on how long an implied warranty lasts, so the above limitation may not apply to you.
Installation
Diagram 1
Diagram 2
Junction Box Outline
(Wall)
Step 1: Choose a location on the wall away from any wall
studs or support beams. Cut a hole through the wall slightly
larger than the junction box. Use the junction box as a template
by placing the open side of the box against the wall (Diagram
1).
Step 2: Drill a 0.25” hole through the back of the junction box
in the center, the center is marked for accuracy. Also drill any
holes needed for wiring (Diagram 2).
Drill a 0.25" hole in
the center of the back
of the junction box.
Diagram 3
Diagram 4
Step 3: Place the bracket with the integral nut on top of the
other bracket and turn it to form a “+” (Diagram 3). Place the
junction box inside the “+”. Slide the mounting screw through
the holes in the junction box and inner bracket and thread it
into the integral nut of the back bracket until it just comes out
the other side (Diagram 4).
Integral Nut
Step 5: Tighten the screw until the box is secure. This will pull
the bracket tight against the wall (Diagram 6). The junction box
is now ready for final wiring and doorbox mounting.
Note: Once the bracket assembly is in place, it can not be
removed without losing the back bracket.
Product Support Line...715.386.8666
Diagram 5
(Wall)
Pre-Cut Hole
Use the screw to push the bracket
assembly and box into the hole.
Diagram 6
Pre-Cut Hole
(Wall)
Step 4: Pull the wiring through the junction box from the back
side and then insert the box and bracket assembly into the
hole in the wall by pressing on the head of the screw (Diagram
5). Make sure both wings of the back bracket clear the wall
completely. Important: For proper installation, use the head
of the screw to push the bracket and box into the wall.
Mounting Screw
Tighten the screw until the
back bracket is pulled tight.
Fax Back Line...715.386.4345
Due to the dynamic nature of the product design, the information contained in this document is subject to change without notice. Viking Electronics, and its affiliates and/or subsidiaries assume no responsibility for errors and omissions contained in this information. Revisions of this document or new editions of it may be issued to incorporate such changes.
Fax Back Doc 431
Printed in the U.S.A.
ZF302040 Rev A
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement