BandTel SIP Trunk Setup Guide
DSX
BandTel SIP Trunk Setup
April 22, 2011
Issue 1.02
NEC Corporation of America
4 Forest Parkway, Shelton, CT 06484
BandTel SIP Trunk Setup
DSX
1.02
Copyright 2011
NEC Corporation of America
6535 N. State Highway 161
Irving, TX 75039-2402
Communications Technology Group
Revision History
Issue
Date
1.00
2/24/11
•
Initial release.
1.01
3/18/11
•
Updated the program refer to 2101-05 in paragraph 4.7.
1.02
4/22/11
•
Updated required software level, expanded RTP port forwarding
range, and added System Administrator screen shots.
•
Removed requirement for 1104-09.
NEC Corporation of America
Revisions
Page 2 of 8
April 22, 2011
DSX
BandTel SIP Trunk Setup
1.02
Contents
1 Overview................................................................................................................................................ 4 2 BandTel Setup ....................................................................................................................................... 4 3 System Router Setup............................................................................................................................. 4 3.1 NAT and SIP....................................................................................................................................... 4 3.2 Port Forwarding .................................................................................................................................. 4 4 DSX Setup ............................................................................................................................................. 4 4.1 Software Level .................................................................................................................................... 4 4.2 Assign SIP Lines................................................................................................................................. 5 4.3 Select the SIP Trunk Provider Type ................................................................................................... 6 4.4 Set Up the SIP Trunk Registration...................................................................................................... 6 4.5 Codec Setup ....................................................................................................................................... 7 4.6 Assign ANI Numbers to your SIP Lines .............................................................................................. 7 4.7 Fax Setup ........................................................................................................................................... 8 Tables
Table 1: BandTel Account Information......................................................................................................... 4 NEC Corporation of America
Page 3 of 8
April 22, 2011
DSX
1
BandTel SIP Trunk Setup
1.02
Overview
The DSX is compatible with BandTel SIP Trunking. This setup guide summarizes the account information
you will receive from BandTel and provides step-by-step instructions on how to program that information
into the DSX.
You must set up SIP trunks as DID lines. All the feature available with other types of DID lines are also
available with BandTel SIP trunk lines. For details on the features available with DID lines, refer to the online DSX Software Manual at: http://www.necdsx.com/docs/dita/dsx_v3_complete/index.html
2
BandTel Setup
To set up your SIP trunking account, contact BandTel at http://www.bandtel.com. Once your account is
set up you need the service information:
Table 1: BandTel Account Information
Option
Server Address
User
Password
3.1
The Server Address is the SIP registration domain for your
BandTel SIP trunks. When your SIP trunks initially register
they use this address.
This is the username that BandTel uses to authenticate your
registration.
This is the password required with your Login.
DID Number(s)
These are the telephone numbers that users will dial to reach
you over your BandTel SIP trunks.
ANI Number(s)
These are the outgoing telephone numbers that must be
programmed for each of your BandTel SIP trunks.
DNS #1
3
Description
BandTel uses their own DNS server. This should be the first
DNS entry in the DSX.
System Router Setup
NAT and SIP
In the router to which the DSX is connected, enable NAT and disable all special SIP management
features (such as SIP ALG).
3.2
Port Forwarding
Forward UDP ports 5060 and 1024 through 1215 to the DSX system’s IP address.
4
4.1
DSX Setup
Software Level
3.31.96 or higher.
NEC Corporation of America
Page 4 of 8
April 22, 2011
DSX
4.2
BandTel SIP Trunk Setup
1.02
Assign SIP Lines
1231-01: IP Lines [SYSTEM: PORTS: IP LINES: IP LINE ASSIGNMENT]
The first DSX SIP line is the first line beyond the last assigned line. Each SIP line uses an IP
resource (licensed VoIP port) in DSX. The maximum number of VoIP licenses is 8 in DSX-40 and
16 in DSX-80/160.
Example with DSX-40:
•
The first SIP line in a DSX-40 without a COIU expansion card is line 5. Available SIP line
numbers are 5-12.
•
With the COIU expansion card installed, the first SIP line is line 9. Available SIP line
numbers are 9-16.
•
DSX-40 supports a maximum of 8 VoIP licenses. When the total number of licenses are in
use, only Peer-to-Peer calls are available.
Example with DSX-80/160:
•
The first SIP line in a DSX-80/160 with a single 8COIU card is line 9. Available SIP lines
are 9-17.
•
The last line number in DSX-80/160 is 64. In a system with an 8COIU and two T1/PRI
cards, this will limit the available number of SIP lines.
•
DSX-80/160 supports a maximum of 16 VoIP licenses. When the total number of licenses
are in use, only Peer-to-Peer calls are available.
1232-01: IP Line Provider Number [SYSTEM: PORTS: IP LINES: IP LINE ASSIGNMENT]
Assign each SIP line in DSX to a provider number (1 or 2). DSX supports up to two providers
simultaneously.
Example: If BandTel is your only SIP trunk provider, assign all the SIP lines designated in 1231-01
to provider 1.
1232-02: IP Line Username [SYSTEM: PORTS: IP LINES: IP LINE ASSIGNMENT]
1232-03: IP Line Password [SYSTEM: PORTS: IP LINES: IP LINE ASSIGNMENT]
These options are not used with BandTel SIP trunks.
NEC Corporation of America
Page 5 of 8
April 22, 2011
DSX
4.3
BandTel SIP Trunk Setup
1.02
Select the SIP Trunk Provider Type
1831-01: Provider Number [SYSTEM: VOIP: PROVIDERS: PROVIDER (1 OR 2)]
Select the provider number you want to set up. This selection corresponds to the provider number
you assigned to the SIP lines in 1232-01.
Example: If BandTel is your only SIP trunk provider, and you have chosen provider 1 in 1232-01,
select provider 1 for this option also.
1831-02: Provider Type [SYSTEM: VOIP: PROVIDERS: PROVIDER (1 OR 2): SERVICE PROVIDER]
Dial 11 to choose BandTel as the type for the provider selected in 1831-01.
1831-03: Provider Name [SYSTEM: VOIP: PROVIDERS: PROVIDER (1 OR 2): DESCRIPTION]
The provider name is an optional 18-character entry that describes the provider. Enter any name
you like – the entry does not affect provider setup or registration.
1831-04: Profile [SYSTEM: VOIP: PROVIDERS: PROVIDER (1 OR 2): PROFILE]
Select the VoIP profile that the system will use when connecting to the SIP trunk provider. The
entry you make here corresponds to the profiles set up in programs 1811-1815. Choose profile 4.
4.4
Set Up the SIP Trunk Registration
1832-01: Provider IP Registration [SYSTEM: VOIP: PROVIDERS: PROVIDER (1 OR 2): SERVER ADDRESS]
Select the provider number you want to set up (see 1831-01) and enter the Table 1 Server Address
as it was provided to you by BandTel. This option uses the text entry method.
1832-02: Registration Type [SYSTEM: VOIP: PROVIDERS: PROVIDER (1 OR 2): REGISTRATION TYPE]
Choose the IP line registration type. DSX IP lines can share the same registration (01: Common) or
have a unique registration for each line (02: Per Line). For BandTel, choose 01: Common.
1832-03: Account Username [SYSTEM: VOIP: PROVIDERS: PROVIDER (1 OR 2): USER]
Enter the username for your BandTel SIP trunk account. This option uses the text entry method
and is the User entry in Table 1.
1832-04: Account Password [SYSTEM: VOIP: PROVIDERS: PROVIDER (1 OR 2): PASSWORD]
This option is the password associated with the Account Username assigned in 1832-03. The
password can be up to 24 characters long. This is the Password entry in Table 1.
1832-05: Proxy [SYSTEM: VOIP: PROVIDERS: PROVIDER (1 OR 2): PROXY ADDRESS]
1832-06: SIP Type or Service (ToS) [SYSTEM: VOIP: PROVIDERS: PROVIDER (1 OR 2): SIP TOS]
1832-07: RTP Type of Service (ToS) [SYSTEM: VOIP: PROVIDERS: PROVIDER (1 OR 2): RTP TOS]
These options are not used with BandTel SIP trunks.
NEC Corporation of America
Page 6 of 8
April 22, 2011
DSX
4.5
BandTel SIP Trunk Setup
1.02
Codec Setup
1812: Codecs [SYSTEM: VOIP: PROFILE 4: CODECS]
For BandTel SIP Trunks, for Profile 4 set:
- Codec 1 to G.729, 20mS Frame Size.
- Codec 2 to G.711, 20mS Frame Size
Set all other priorities to None.
4.6
Assign ANI Numbers to your SIP Lines
3101-07: Telephone Number [LINES: CONFIG: SETUP: TYPE: PHONE NUMBER]
For each of your SIP lines, enter a telephone number that corresponds to one of the ANI Numbers
in Table 1. Each line must have a unique entry.
BandTel SIP trunks ignore the settings in 2101-05: Outgoing ANI ID [STATIONS: CONFIG: SETUP: TYPE:
ANI ID] and 1011-02: Telephone Number [SYSTEM: CONFIG: SETUP: IDENTIFICATION: PHONE NUMBER].
NEC Corporation of America
Page 7 of 8
April 22, 2011
DSX
4.7
BandTel SIP Trunk Setup
1.02
Fax Setup
1812: Codecs [SYSTEM: VOIP: PROFILE X: CODECS]
1815: DTMF [SYSTEM: VOIP: PROFILE X: PAYLOAD TYPES]
SIP trunks to be used for fax must be set for G.711, 20mS Frame Size, with Inband DTMF. The fax
is transmitted in-band DTMF only.
NEC Corporation of America
Page 8 of 8
April 22, 2011
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement