Cardinal Detecto 6735 Owner`s manual

Cardinal Detecto 6735 Owner`s manual
758C
WEIGHT INDICATOR
With Body Mass Index Features
Owner’s Manual
8555-M210-O1 Rev R
11/12
Cardinal Scale Manufacturing Co.
PO BOX 151 WEBB CITY, MO 64870
PH (417) 673-4631 - FAX (417) 673-5001
www.detectoscale.com
Technical Support:
Ph: 866-254-8261
[email protected]
8555-M210-O1
Rev R yx 758C
Owner’s
Printed in USA
1
2
8555-M210-O1 Rev R y 758C Owner’s
TABLE OF CONTENTS
INTRODUCTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
SPECIFICATIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Standard Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Optional Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
SITE PREPARATION REQUIREMENTS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
INSTALLATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Unpacking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Mounting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
INTERCONNECTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Optional AC Power Adapter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Height Rod Option – Detecto DHR . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Load Cell . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
USB . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
USB, Serial & Ethernet Interface Specifications . . . . . . . . . . . . . . . . . . . . . . . .
Serial I/O Port . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Ethernet (758-IPOption) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
BATTERIES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Battery Status . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Low Battery Indicator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Battery Installation/Replacement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
KEYPAD FUNCTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Basic Functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Body Mass Index Functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
ANNUNCIATORS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
OPERATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Basic Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Basic Operation with ID . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Body Mass Index Operation
(Using Mechanical Height Rod or Manually Entering Height) . . . . . . . . . . . .
Body Mass Index Operation with ID
(Using Mechanical Height Rod or Manually Entering Height) . . . . . . . . . . . .
Body Mass Index Operation (Using Digital Height Rod) . . . . . . . . . . . . . . . . . .
Body Mass Index Operation with ID (Using Digital Height Rod) . . . . . . . . . . . .
SETUP AND CALIBRATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
SETUP REVIEW . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
PRINTER TICKET FORMATS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
WEIGHT ON DEMAND FORMATS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
SERIAL AND USB DEVICE PORT COMMANDS . . . . . . . . . . . . . . . . . . . . . . . .
ERROR AND STATUS DISPLAYS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
BEFORE YOU CALL SERVICE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
EVENT COUNTER . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
CARE AND CLEANING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
PARTS IDENTIFICATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
8555-M210-O1 Rev R y 758C Owner’s
Page 1
Page 1
Page 1
Page 1
Page 3
Page 4
Page 4
Page 4
Page 5
Page 5
Page 5
Page 5
Page 5
Page 5
Page 6
Page 6
Page 6
Page 7
Page 7
Page 7
Page 8
Page 8
Page 9
Page 11
Page 13
Page 13
Page 14
Page 15
Page 15
Page 16
Page 17
Page 19
Page 30
Page 31
Page 32
Page 33
Page 35
Page 35
Page 36
Page 36
Page 39
I1
FCC COMPLIANCE STATEMENT
WARNING! This equipment generates uses and can radiate radio frequency and if not
installed and used in accordance with the instruction manual, may cause interference to radio
communications. It has been tested and found to comply with the limits for a Class A
computing device pursuant to Subpart J of Part 15 of FCC rules, which are designed to provide
reasonable protection against such interference when operated in a commercial environment.
Operation of this equipment in a residential area may cause interference in which case the
user will be responsible to take whatever measures necessary to correct the interference.
You may find the booklet “How to Identify and Resolve Radio TV Interference Problems”
prepared by the Federal Communications Commission helpful. It is available from the U.S.
Government Printing Office, Washington, D.C. 20402. Request stock No. 001-000-00315-4.
PROPER DISPOSAL
When this device reaches the end of its useful life, it must be properly disposed of. It must not
be disposed of as unsorted municipal waste. Within the European Union, this device should
be returned to the distributor from where it was purchased for proper disposal. This is in
accordance with EU Directive 2002/96/EC. Within North America, the device should be
disposed of in accordance with the local laws regarding the disposal of waste electrical and
electronic equipment.
It is everyone’s responsibility to help maintain the environment and to
reduce the effects of hazardous substances contained in electrical and
electronic equipment on human health. Please do your part by making
certain that this device is properly disposed of. The symbol shown to the
right indicates that this device must not be disposed of in unsorted
municipal waste programs.
All rights reserved. Reproduction or use, without expressed written permission, of editorial or
pictorial content, in any manner, is prohibited. No patent liability is assumed with respect to
the use of the information contained herein. While every precaution has been taken in the
preparation of this manual, the Seller assumes no responsibility for errors or omissions.
Neither is any liability assumed for damages resulting from use of the information contained
herein. All instructions and diagrams have been checked for accuracy and ease of application;
however, success and safety in working with tools depend to a great extent upon the individual
accuracy, skill and caution. For this reason the Seller is not able to guarantee the result of any
procedure contained herein. Nor can they assume responsibility for any damage to property or
injury to persons occasioned from the procedures. Persons engaging the procedures do so
entirely at their own risk.
Serial Number ______________________
PRECAUTIONS
Date of Purchase ___________________
Before using this indicator, read this manual
and pay special attention to all "WARNING"
symbols:
Purchased From ____________________
___________________________________
___________________________________
___________________________________
IMPORTANT
RETAIN THIS INFORMATION FOR FUTURE USE
II
2II
8555-M210-O1 Rev R y 758C Owner’s
ELECTRICAL
WARNING
INTRODUCTION
Thank you for purchasing our Model 758C Weight Indicator. It has been manufactured with
quality and reliability at our factory in Webb City, MO USA. This Indicator has been tested
before leaving our factory to insure accuracy and dependability for years to come.
This manual is provided to guide you through installation, operation and maintenance of your
indicator. Please read it thoroughly before attempting to install or operate your 758C and keep
it handy for future reference.
SPECIFICATIONS
Power Requirements . . . . . . . . 6 “C” cell Alkaline, Ni-Cad or NiMH batteries (not included)
OR an optional 100 to 240 VAC 50/60Hz 12 VDC 1A wall
plug-in UL/CSA listed AC power adapter (Cardinal part
number 6800-1045).
Operating Temperature . . . . . . 14 to 104 ºF (-10 to +40 ºC)
Display . . . . . . . . . . . . . . . . . . . Weight: Five digit, seven segment, 1/2” (13 mm) high LCD
Height: Four digit, seven segment, 3/8" (10 mm) high LCD
Sensitivity . . . . . . . . . . . . . . . . . 1.2 uV/division (0 to 3.0 mV/V), Class III
Signal Input Range . . . . . . . . . 0 to 15mV max.
Transducer Excitation . . . . . . . 5.0 VDC
Number of Load Cells . . . . . . . up to 4 each 350:
Load Cell Cable Length . . . . . . 10 feet (3 meters) max.
Resolution . . . . . . . . . . . . . . . . 5,000 divisions
Capacities . . . . . . . . . . . . . . . . 1,000 to 5,000 divisions commercial
up to 10,000 divisions noncommercial
Division Value . . . . . . . . . . . . . 1, 2, 5 or 10 x 1, 0.1, 0.01, 0.001
Sample Rate . . . . . . . . . . . . . . 1 to 10 samples per second selectable
Auto Zero Range . . . . . . . . . . . 0.5 or 1 through 9 divisions
Weighing Units . . . . . . . . . . . . . Pounds, kilograms, ounces, grams or
Stones and pounds/kilograms
Keyboard . . . . . . . . . . . . . . . . . Membrane type with 19 keys
Enclosure Size . . . . . . . . . . . . . 9.5" W x 6.625" H x 2.125" D (24 cm W x 17 cm H x 5 cm D)
Construction . . . . . . . . . . . . . . . Painted Steel
Standard Features:
x
x
x
x
Metric Conversion
Auto Shut-Off Feature
Selectable Sleep-Mode
Selectable Filtering
x
x
x
Serial I/O (Input/Output)
USB Device Port
Height Rod Port (for Optional
Detecto Digital Height Rod)
x
x
Optional 12VDC AC Power Adapter
Optional Welch Allyn® WAConnect
Optional Features:
x
x
758-IP Ethernet Option
Detecto DHR (Digital Height Rod)
8555-M210-O1 Rev R y 758C Owner’s
1
This page intentionally left blank.
2
8555-M210-O1 Rev R y 758C Owner’s
SITE PREPARATION REQUIREMENTS
The Model 758C Weight Indicator is a precision weight indicating instrument. As with any
precision instrument, it requires an acceptable environment to operate at peak performance
and reliability. This section is provided to assist you in obtaining such an environment.
Environmental
The Model 758C Weight Indicator meets or exceeds all certification requirements within a
temperature range of 14 to 104 °F (-10 to +40 °C).
In order to keep cooling requirements to a minimum, the indicator should be placed out of
direct sunlight and to provide adequate air circulation, keep the area around the indicator clear.
Do not place the indicator directly in front of a heating or cooling vent. Such a location will
subject the indicator to sudden temperature changes, which may result in unstable weight
readings.
Insure that the indicator has good, clean AC power and is properly grounded. In areas subject
to lightning strikes, additional protection to minimize lightning damage, such as surge
suppressors, should be installed.
Electrical Power
The 758C indicator has been designed to operate from a 100 to 240 VAC 50/60Hz 12 VDC 1A
wall plug-in UL/CSA listed AC power adapter. Note that a special order is not required for
operation at 230 VAC.
ƒ
The socket-outlet supplying power to the indicator should be on a separate circuit from the
distribution panel and dedicated to the exclusive use of the indicator.
ƒ
The socket-outlet shall be installed near the equipment and shall be easily accessible.
ƒ
The wiring should conform to national and local electrical codes and ordinances and should
be approved by the local inspector to assure compliance.
ƒ
On installations requiring 230 VAC power, it is the responsibility of the customer to have
a qualified electrician install the proper power adapter plug that conforms to national
electrical codes and local codes and ordinances.
8555-M210-O1 Rev R y 758C Owner’s
3
INSTALLATION
Unpacking
Carefully remove indicator from shipping carton and inspect it for any damage that may have
taken place during shipment. Keep carton and packing material for return shipment if it should
become necessary. The purchaser is responsible for filing all claims for any damages or loss
incurred during transit.
Should your indicator come already installed on a scale, the following installation
information does not apply to you.
Bracket Mount
Screws
Latch
Release
Latch
Battery Door
Thumb Screw
Figure No. 1
Mounting
The indicator may be mounted (using an optional bracket) to a desktop, table or bench. It can
be mounted on a wall using the two (2) holes in the mounting bracket and two (2) #10 screws
placed 2.00 inches (51 mm) apart in the wall.
To install indicator on bracket, push latch release down flush with back of indicator and hold.
Next, place large end of slotted holes in bracket over screw heads on back of indicator. Pull
down to secure indicator. Release latch release to lock indicator to bracket. See Figure No. 1.
Regardless of how and where you mount indicator, it should be in a safe area where it will not
be in the way of normal traffic. The location chosen should be free of temperature extremes
and water, is not subject to direct sunlight and should be mounted where the display is easily
viewed and within easy reach of the operator.
If wall mounted, make certain the structure and mounting bolts are of sufficient strength to
support the indicator. The mounting bracket should be securely fastened to the wall so it
cannot break loose.
4
8555-M210-O1 Rev R y 758C Owner’s
INSTALLATION, CONT.
INTERCONNECTIONS
All input, output, options and power connections to the 758C are made at the rear panel of the
indicator. Connections for the Load Cell input and the Serial I/0 are made using 9-pin "D"
shaped connectors. The Height Rod option (Detecto DHR, Digital Height Rod) and Ethernet
(758-IP) options use snap-in modular connectors. The USB port is a device (or upstream) port
using an industry standard “B” connector. The optional 12VDC wall plug-in UL/CSA listed AC
power adapter is connected using a power jack. Refer to Figure No. 1.
Optional AC Power Adapter
To power the 758C using the optional 12VDC wall plug-in AC power adapter, connect the plug
from the adapter into the power jack on the back of the indicator and then plug the power
adapter into the proper electrical outlet. Refer to Figure No. 1. On models requiring 220 VAC,
it is the customer’s responsibility to obtain the correct power adapter plug.
Height Rod – Detecto DHR (Digital Height Rod) Option
The optional Detecto DHR (Digital Height Rod) connects to the 758C by a snap-in modular
connector socket. Insert the modular connector of the DHR cable into the socket on the rear of
the display it locks in place (a clicking sound will be heard when it is locked in place).
Load Cell
The load cell cable connects to the 758C via a 9-pin "D" connector on
the rear panel of the indicator. Figure No. 2 shows the pin
identification for the load cell connector. Make certain that the pins
are correctly identified before soldering a wire to them. Use the
connector retaining screws to hold the load cell cable connector
securely to the rear panel.
5
9
PIN NO.
1
2
3
4
5
FUNCTION
+EXCITATION
-SIGNAL
No Connection
No Connection
SHIELD
PIN NO.
6
7
8
9
FUNCTION
-EXCITATION
+SIGNAL
No Connection
No Connection
4
8
3
7
2
6
MATING CONNECTOR INFORMATION
DESCRIPTION
ITEM
CONNECTOR
DE9-P
CONNECTOR SHELL C883010001
1
Cardinal Part #
6610-2379
6610-1131
USB
Figure No. 2
The USB port is a device (or upstream) port and uses readily
available cables with the industry standard “B” connector.
USB, Serial and Ethernet Interface Specifications
The 758C USB, Serial and optional Ethernet interfaces can be configured during the setup and
calibration procedure or during the setup review operation. Using either method, it is possible
to select the operation of the interfaces.
The interfaces may be connected to a computer for transmission of weight and associated
data to a PC-based EMR (electronic medical record) software program. The data can be
transmitted on demand (pressing the PRINT/ENTER key) or on receipt of a command from the
computer. Note that only the serial interface can be connected to a printer to record weight
and associated data.
8555-M210-O1 Rev R y 758C Owner’s
5
INSTALLATION, CONT.
Serial I/O Port
The 758C RS-232 serial I/O port is a 9-pin "D" connector on the rear
panel of the indicator. Figure No. 3 shows the Serial I/0 connector
along with the identity of the pins used. Make certain that the pins
are correctly identified before soldering a wire to them. Use the
connector retaining screws to hold the serial cable connector securely
to the rear panel.
PIN NO.
FUNCTION
2
DATA INPUT (RXD)
3
DATA OUTPUT (TXD)
5
SIGNAL GROUND (GND)
5
9
4
8
3
Note that pins 1, 4 and 6 through 9 are not used.
The 758C RS-232 serial interface can be configured during the setup
and calibration procedure or during the setup review operation. Using
either method, it is possible to select the operation of the serial
interface as well as select the baud rate.
x
x
x
The baud rates supported are: 1200, 2400, 4800, 9600, 19.2K
and 38.4K baud.
The data format is fixed at 8 bits, No parity, and 1 stop bit.
The indicator is shipped from the factory with the baud rate set
to 9600 baud.
7
2
6
1
Figure No. 3
Ethernet (Optional)
The 758C Ethernet option requires the purchase of the optional 758-IP Ethernet Interface
Option. Once installed, connections to the 758C are by CAT 5 or equivalent cable. Consult
your network administrator for the proper procedure to terminate and connect the cable.
BATTERIES
The 758C indicator can use 6 "C" size Alkaline, Ni-Cad or NiMH batteries (not included). You
must first obtain and install batteries before operations can begin. Batteries are contained in a
battery holder inside indicator. Access is via a removable panel on back of indicator.
CAUTION! The 758C can be operated from Alkaline, Ni-Cad or NiMH batteries. All
six (6) batteries must be of the same type. They must all be Alkaline, all Ni-Cad or
all NiMH. DO NOT mix Alkaline and Ni-Cad or NiMH batteries.
IMPORTANT! The 758C does not have a battery charging circuit. Should you wish
to use Ni-Cad or NiMH batteries, they must be fully charged before installing. When
discharged, Ni-Cad or NiMH batteries must be removed and placed in an external
charger to recharge.
CAUTION: RISK OF EXPLOSION IF BATTERY IS REPLACED BY AN INCORRECT
TYPE. DISPOSE OF USED BATTERIES ACCORDING TO THE INSTRUCTIONS.
ATTENTION: RISQUE D'EXPLOSION SI LA BATTERIES EST REMPLACE'E PAR UN
TYPE INCORRECT. REJETEZ LES BATTERIES UTILISE'ES SELON LES
INSTRUCTIONS.
6
8555-M210-O1 Rev R y 758C Owner’s
INSTALLATION, CONT.
Battery Status
If batteries are used, the indicator will show battery status on power up. The display will show
battry then change to ð YY ð, where YY indicates remaining battery voltage expressed as a
percentage (%) of total battery voltage
Low Battery Indicator
When batteries are near the point they need to be replaced (Alkaline) or recharged (NiCad or
NiMH), the low battery annunciator on display will turn on. (See Figure No. 5 or 6). If the
battery voltage drops too low for accurate weighing, the indicator will automatically shut off and
you will be unable to turn it back on.
Using Alkaline Batteries
When the low battery annunciator turns on, turn the indicator off, remove the old batteries
and replace with new ones.
Using NiCad or NiMH Batteries
When the low battery annunciator turns on, turn the indicator off, remove the discharged
batteries and replace with fully charged ones. Place the discharged batteries in an external
charger to recharge.
Battery Installation/Replacement
To install or remove the batteries, the following steps should be followed:
1. Make sure the AC power adapter is unplugged.
2. Remove the indicator from the mounting bracket and turn the indicator over so that the
display is facing away from you.
3. Locate the rectangular panel on the back of indicator and remove the thumb screw.
4. Remove the panel (lift straight up and slide it out) exposing the battery holder.
5. If installing new batteries, proceed to step 6. If replacing the batteries, remove all 6
batteries from the battery holder and then proceed to step 6.
6. Install the new 6 "C" size batteries in the holder, noting the polarity markings located in
the battery holder. Refer to Figure No. 4.
7. After placing all 6 batteries in holder, replace panel on back of indicator (slide tab into
slot on rear panel) and install thumb screw.
8. Turn the indicator over (display facing up) and press the ON/OFF key.
9. If display turns on, batteries have been installed correctly. If not, remove panel and
check for one or more improperly positioned batteries.
10. Return the indicator to the mounting bracket.
11. The indicator is now ready for operation.
Figure No. 4
8555-M210-O1 Rev R y 758C Owner’s
7
KEYPAD FUNCTIONS
DO NOT operate the keypad with pointed objects (pencils, pens, etc).
Damage to keypad resulting from this practice is NOT covered under warranty.
Figure No. 5
This is the ON/OFF key. With the indicator off, pressing this key will apply
power to the indicator and turn on the display. If the indicator is already on,
pressing the key again will turn the indicator off.
Basic Functions
This is the ZERO key. It is used to reset the display to zero up to the selected
limit of either 4% or 100% of the scale capacity. The zero limit is set during
setup and calibration of the indicator.
This is the UNITS key. This key is used to change the weighing units to the
alternate units of measurement. For example, with pounds displayed, pressing
this key will change the weighting units to kilograms. NOTE: This feature
must be enabled during setup and calibration for this key to be operational.
8
8555-M210-O1 Rev R y 758C Owner’s
KEYPAD FUNCTIONS, CONT.
This is the LOCK/RELEASE key. It is used to lock and unlock the display. If
the HOLD feature was enabled during setup and calibration, pressing this key
(after obtaining a stable weight) will cause the indicator to lock onto the
weight. Pressing this key again will unlock the display and return it to zero.
If the AUTO LOCK feature was enabled, the weight display will lock after
placing a load on the scale and obtaining a stable weight value. Pressing this
key will unlock the display and return the weight display to zero, or if another
load is applied to the scale, lock onto the new weight after obtaining a stable
weight value. NOTE: The lock feature is for non-commercial (NOT "Legal for
Trade") applications.
Body Mass Index (BMI) Functions
This is the NET/GROSS key. It is used to toggle between Net and Gross
weight modes. The selected mode is indicated by turning on the appropriate
annunciator on the display. Note that if no valid tare weight has been entered,
pressing this key will cause a momentary display -Err- and the indicator will
remain in the Gross weight mode.
This is the TARE key. It is a dual function key. Pressing it and pressing the
PRINT/ENTER key (Pushbutton Tare mode) will cause the current gross
weight to be stored as the new tare weight and change the weight display to
the net weight display mode (Net annunciator will turn on). Pressing this key,
entering a numeric value (Keypad Tare) and then pressing the PRINT/ENTER
key will cause the value entered to be accepted as the new tare weight.
NOTE: Tare weights equal to or greater than scale capacity cannot be entered.
In addition, the keypad tare weight division value must be the same as the scale
division value. For example, a unit with .05 kg as the division value will display
-Err- if you attempt to enter 1.03 for the tare weight.
This is the ID/HEIGHT key. This key is used to display and enter an
identification (ID) number use in the ID Storage feature and to enter the height
(feet and inches or centimeters) for the Body Mass Index (BMI) calculation.
Pressing this key will change the display to show the currently selected
identification (ID) number and allow the entry of a new ID number.
The identification (ID) number can be up to 11 digits. When entering an ID
number, the digits start displaying on the right side of the ID display and
proceed to the left. When an ID greater than 4 digits is used, the digits will
automatically scroll off the left side of the display to show the additional digits
on the right as they are entered.
This is the CLEAR key. It is used to clear an incorrect entry from the display
without processing the data. If an incorrect entry is made, press the CLEAR
key and re-enter the correct data. When entering the ID, pressing the CLEAR
key will act as a “backspace” key (it will back up one space and delete the
character in that space). NOTE: The CLEAR key must be pressed before
the PRINT/ENTER key to ensure the data is not processed.
8555-M210-O1 Rev R y 758C Owner’s
9
KEYPAD FUNCTIONS, CONT.
This is the PRINT/ENTER key. It serves several purposes. First, when
reviewing setup parameters, pressing the PRINT/ENTER key will display the
current setting of the parameter. Second, the PRINT/ENTER key is used to
signal completion of the data entry and causes the indicator to process the
data entered. Third, the PRINT/ENTER key is used to initiate the
transmission of weight and associated data using the selected I/O port.
NOTE: The indicator will not respond to pressing the PRINT/ENTER key unless
the weight display is stable. If displaying gross weight, only the gross weight is
printed. If displaying net weight, the gross, tare, and net weights are printed. If
the ID and BMI features are used, their data is printed along with the weight data.
The 0 through 9 numeric keys are used to enter numeric data
during the setup and calibration as well as during normal
operation of the indicator.
NOTE: The 0 and 1 keys have
dual functions. They are used
to enter numeric data during
setup and calibration as well as
during normal operations and
are also used to select yes or
no to various prompts.
nControl Feature
The 758C includes support for nControl. nControl is
a PC based program that can design a ticket then
download the ticket information to the indicator. The
758C allows 1 programmable format instead of the
ASCII format default ticket.
For more information on nControl, refer to the
nControl Fast Start Guide.
Time, mm/dd/yy
ID:
BMI:
Height:
Weight:
xxxxxxxxxxx
xx.x
xx.x cm
xxx.xuu G
xxx.xuu T
xxx.xuu N
SAMPLE TICKET
NOTE: If the ID/HEIGHT key is disabled, the appropriate field will be left out when
printing a ticket.
10
8555-M210-O1 Rev R y 758C Owner’s
ANNUNCIATORS
The annunciators are turned on to indicate that the display is in the mode corresponding to the
annunciator label or that the status indicated by the label is active.
Figure No. 6
LO BAT
The LO BAT (low battery) annunciator is used with the battery operation. It will turn ON to
indicate that the batteries will soon need to be replaced. No change in operation will occur
until just before the battery voltage drops to a level where operation is affected. At this level,
the indicator will automatically turn itself off.
GROSS
The GROSS annunciator is turned on to show that the weight displayed is the gross weight.
Gross weight will be displayed when no tare weight value is stored.
TARE
The TARE annunciator is turned on to show that the indicator is in a weight mode in which a
known tare (container) weight value is stored.
NET
The NET annunciator is turned on to show that the weight displayed is the net weight. Net
weight is determined by subtracting the stored tare weight from the gross weight. The tare
weight is usually the weight of the empty container. Note that the NET annunciator is only
active when a tare weight value is stored.
[\ (STABLE)
The (Stable) annunciator is turned on when the weight display is stable. When off, it means
that the change in successive weight samples is greater than the motion limits selected during
setup and calibration of the indicator.
ZERO
The ZERO annunciator is turned on to indicate that the weight is within +/- 1/4 division of the
center of zero.
LOCK
The LOCK annunciator is turned on to show that the indicator is locked onto the weight. In
operation after obtaining a stable weight value, pressing the LOCK/RELEASE key (or
resetting the Auto Lock) will cause the indicator to lock onto the weight and turn on the
annunciator. Pressing the LOCK/RELEASE key a second time (or dropping below the Auto
Lock reset value) will unlock the display and turn off the annunciator.
NOTE: The lock feature (Hold Mode) must be enabled during setup and calibration.
8555-M210-O1 Rev R y 758C Owner’s
11
ANNUNCIATORS, CONT.
kg
The kg annunciator is turned on to indicate that the displayed weight is in kilograms.
ST
This annunciator is turned on to indicate that the displayed weight is in Stones.
lb
This annunciator is turned on to indicate that the displayed weight is in pounds.
oz
This annunciator is turned on to indicate that the displayed weight is in ounces.
FT-INCHES
This annunciator is turned on when the displayed height measurement is in feet and inches.
cm
The cm annunciator is turned on to indicate that the displayed height measurement is in
centimeters.
BODY MASS INDEX
The BODY MASS INDEX annunciator is turned on when displaying
the calculated body fat. The bar graph is used to show a graphical
representation (ranging from Low to High) of the Body Mass Index
calculation.
12
8555-M210-O1 Rev R y 758C Owner’s
OPERATION
Basic Operation
To Weigh
1. Press ON/OFF key to turn indicator on.
2. Press ZERO key to zero weight display. ZERO, GROSS and lb, oz, kg or ST
annunciator will turn on to show that the scale is ready for use.
3. Place patient on scale and read weight display.
4. If a printer is connected to scale, press PRINT/ENTER key to print a ticket.
5. Remove patient from scale.
Zero Weight Display
1. In Gross Weight mode (GROSS annunciator on), press ZERO key.
2. Weight display will return to zero. ZERO and STABLE [\ annunciators will turn on
to show a stable, center-of-zero gross weight condition.
Metric Conversion
Press UNITS key to toggle between pounds and kilograms. Note that the lb or kg
annunciator will turn on to show the weighing unit selected.
Push Button Tare (Tare weight is NOT known)
1. In Gross Weight mode (GROSS annunciator
IMPORTANT! Tare entry is not
on), place item (wheelchair, walker, etc…) to
allowed if Auto Hold is enabled.
be tared on scale.
2. Press TARE key.
3. Display will show weight of item on scale and TARE annunciator will turn on.
4. Press PRINT/ENTER key.
5. Display will change to 0.0 and NET annunciator will turn on to show that net weight
is being displayed. The item's weight has been entered as "tare weight".
6. Proceed with weighing operation.
Tare Weight Entry (Tare weight is known)
1. In Gross Weight mode (GROSS annunciator on), press TARE key.
2. Display will show zero or previously entered tare and TARE annunciator will turn on.
3. If weight displayed is acceptable, press PRINT/ENTER key to save it. Otherwise,
use the numeric keys and enter a new tare weight. Note that when entering tare
weights, a maximum of 4 digits can be entered and the numbers advance from right
to left in the display. The number of leading or trailing zeros required to obtain your
desired tare is dependent upon the DIVISION VALUE selected in the setup
procedure.
For example:
Division Value:
Desired Tare Value:
Key Sequence:
0.2
1.6 lb
16
4. After the new tare weight has been entered, press PRINT/ENTER key.
5. Display will show a minus Net weight and NET annunciator will turn on.
6. Proceed with weighing operation.
Tare Weight Recall
1. In Net Weight mode (NET annunciator on), press TARE key.
2. Display will show previously entered tare for approximately 1 second and then return
to Net Weight mode (NET annunciator on).
To Clear the Tare Weight
1. Press NET/GROSS key to return to Gross weight mode.
2. Remove all material from scale platform and press ZERO key. This will reset tare
weight to zero.
8555-M210-O1 Rev R y 758C Owner’s
13
OPERATION, CONT.
Basic Operation with ID
To Weigh
1. Press ON/OFF key to turn indicator on.
2. Press ZERO key to zero weight display. ZERO, GROSS and lb, oz, kg or ST
annunciator will turn on to show scale is ready for use.
3. Press ID/HEIGHT key.
4. Display will change to show id=.
5. Using numeric keys, key-in up to an 11 digit identification number.
6. Press PRINT/ENTER key.
7. Place patient on scale
8. Read weight display.
9. If a printer is connected to scale, press PRINT/ENTER key to print a ticket.
10. Remove patient from scale.
Push Button Tare (Tare weight is NOT known)
1. In Gross Weight mode (GROSS annunciator
IMPORTANT! Tare entry is not
on), place item (wheelchair, walker, etc…) to
allowed if Auto Hold is enabled.
be tared on scale.
2. Press TARE key.
3. Display will show weight of item on scale and TARE annunciator will turn on.
4. Press PRINT/ENTER key.
5. Display will change to zero and NET annunciator will turn on to show that net weight
is being displayed. The item's weight has been entered as "tare weight".
6. Press ID/HEIGHT key.
7. Display will change to show id=.
8. Using numeric keys, key-in up to an 11 digit identification number.
9. Press PRINT/ENTER key.
10. Proceed with weighing operation.
Tare Weight Entry (Tare weight is known)
1. In Gross Weight mode (GROSS annunciator on), press TARE key.
2. Display will show 0.0 or previously entered tare and TARE annunciator will turn on.
3. If weight displayed is acceptable, press PRINT/ENTER key to save it. Otherwise,
use the numeric keys and enter a new tare weight. Note that when entering tare
weights, a maximum of 4 digits can be entered and the numbers advance from right
to left in the display. The number of leading or trailing zeros required to obtain your
desired tare is dependent upon the DIVISION VALUE selected in the setup
procedure.
For example:
1.
2.
3.
4.
5.
6.
7.
14
Division Value:
Desired Tare Value:
Key Sequence:
0.2
1.6 lb
16
After the new tare weight has been entered, press PRINT/ENTER key.
Display will show a minus Net weight and NET annunciator will turn on.
Press ID/HEIGHT key.
Display will change to show id=.
Using numeric keys, key-in up to an 11 digit identification number.
Press PRINT/ENTER key.
Proceed with weighing operation.
8555-M210-O1 Rev R y 758C Owner’s
OPERATION, CONT.
Body Mass Index (BMI) Operation
Using Mechanical Height Rod or Manually Entering Height
1. Press ON/OFF key to turn indicator on.
2. Press ZERO key to zero weight display. ZERO, GROSS and lb, oz, kg or ST annunciator
will turn on to show scale is ready for use.
3. Perform tare operation if required. Refer to Push Button Tare or Tare Weight Entry in
previous section for instructions on using tare.
4. Place patient on the scale and then press ID/HEIGHT key.
5. If Pounds Only or Pounds/Kilograms was selected for Unit= in setup, display will change
to show FEEt=.
a. Use numeric keys to enter 1 digit for height in feet, then press PRINT/ENTER key.
b. Display will change to show inCH=.
c. Use numeric keys to enter up to 3 digits (11.9 max.) for height in inches and then
press PRINT/ENTER key or press PRINT/ENTER key if no inches are required.
6. If Kilograms Only, Kilograms/Pounds or Stones and Pounds or Kilograms was selected for
Unit= in setup, display will change to show Cn=_.
a. Use numeric keys to enter up to 4 digits (# # # . #) for height in centimeters and then
press PRINT/ENTER key.
7. Read weight and BMI displays.
8. If a printer is connected to scale, press PRINT/ENTER key to print a ticket.
9. Remove patient from scale.
10. If Tare operation was performed, press NET/GROSS key to return to Gross weight mode.
11. Press ZERO key. This will reset tare weight to zero.
12. BMI display will clear when weight returns to zero.
Body Mass Index (BMI) Operation with ID
Using Mechanical Height Rod or Manually Entering Height
1. Press ON/OFF key to turn indicator on.
2. Press ZERO key to zero weight display. ZERO, GROSS and lb, oz, kg or ST annunciator
will turn on to show scale is ready for use.
3. Press ID/HEIGHT key.
4. Display will change to show id=.
5. Using numeric keys, key-in up to an 11 digit identification number.
6. Press PRINT/ENTER key.
7. Place patient on the scale and then press ID/HEIGHT key.
8. If Pounds Only or Pounds/Kilograms was selected for Unit= in setup, display will change
to show FEEt=.
a. Use numeric keys to enter 1 digit for height in feet, then press PRINT/ENTER key.
b. Display will change to show inCH=.
c. Use numeric keys to enter up to 3 digits (11.9 max.) for height in inches and then
press PRINT/ENTER key or press PRINT/ENTER key if no inches are required.
9. If Kilograms Only, Kilograms/Pounds or Stones and Pounds or Kilograms was selected
for Unit= in setup, display will change to show Cn=_.
a. Use numeric keys to enter up to 4 digits (# # # . #) for height in centimeters and then
press PRINT/ENTER key.
10. Read weight and BMI displays.
11. If a printer is connected to scale, press PRINT/ENTER key to print a ticket.
12. Remove patient from scale.
13. If Tare operation was performed, press NET/GROSS key to return to Gross weight mode.
14. Press ZERO key. This will reset tare weight to zero.
15. BMI display and ID will clear when weight returns to zero.
8555-M210-O1 Rev R y 758C Owner’s
15
OPERATION, CONT.
Body Mass Index (BMI) Operation with DHR
Using Digital Height Rod
IMPORTANT! Before performing the operations on this page, the digital height
rod must be in its “starting position” (inner sliding tube must be down
completely inside outer stationary tube and headpiece folded flat against
stationary tube) prior to turning on the indicator. Otherwise, the error
message 999.9 will be displayed.
1. Make sure height rod is in starting position.
2. Press ON/OFF key to turn indicator on.
3. Press ZERO key to zero weight display. ZERO, GROSS and lb, oz, kg or ST
annunciator will turn on to show scale is ready for use. Note that height reading will
show 3-&3 FT-INCHES or 110.0 cm (depending on Unit= setting in Setup).
4. Perform tare operation if required. Refer to Push Button Tare or Tare Weight Entry in
previous section for instructions on using tare.
5. Place patient on the scale.
6. Grasp height rod at hinge pin (see Figure No. 7) and raise it
well above patient’s head and then lift headpiece to horizontal
position. Carefully lower height rod until headpiece rests on
top of patient’s head.
7. BMI will automatically be displayed with height.
8. Read weight, height and BMI displays.
9. If height rod was used, while holding headpiece horizontal,
raise height rod well above patient’s head.
10. Remove patient from scale and return height rod to starting
position.
11. If Tare operation was performed, press NET/GROSS key to
return to Gross weight mode.
12. Press ZERO key. This will reset tare weight to zero.
13. BMI display will clear when weight returns to zero.
16
8555-M210-O1 Rev R y 758C Owner’s
Figure No. 7
OPERATION, CONT.
Body Mass Index (BMI) Operation with ID and DHR
Using Digital Height Rod
IMPORTANT! Before performing the operations on this page, the digital height
rod must be in its “starting position” (inner sliding tube must be down
completely inside outer stationary tube and headpiece folded flat against
stationary tube) prior to turning on the indicator. Otherwise, the error
message 999.9 will be displayed.
1. Make sure height rod is in starting position.
2. Press ON/OFF key to turn indicator on.
3. Press ZERO key to zero weight display. ZERO, GROSS and lb, oz, kg or ST
annunciator will turn on to show scale is ready for use. Note that height reading will
show 3-&3 FT-INCHES or 110.0 cm (depending on Unit= setting in Setup).
4. Perform tare operation if required. Refer to Push Button Tare or Tare Weight Entry in
previous section for instructions on using tare.
5. Press ID/HEIGHT key.
6. Display will change to show id=.
7. Using numeric keys, key-in up to an 11 digit identification number.
8. Press PRINT/ENTER key.
9. Place patient on scale.
10. Grasp height rod at hinge pin (see Figure No. 7) and raise it
well above patient’s head and then lift headpiece to horizontal
position. Carefully lower height rod until headpiece rests on
top of patient’s head.
11. BMI will automatically be displayed with height.
11. Read weight, height and BMI displays.
12. If a printer is connected to scale, press PRINT/ENTER key to
print a ticket.
13. If height rod was used, while holding headpiece horizontal,
raise height rod well above patient’s head.
14. Remove patient from scale and return height rod to starting
position.
Figure No. 8
15. If Tare operation was performed, press NET/GROSS key to
return to Gross weight mode.
16. Press ZERO key. This will reset tare weight to zero.
17. BMI display and ID will clear when weight returns to zero.
8555-M210-O1 Rev R y 758C Owner’s
17
18
8555-M210-O1 Rev R y 758C Owner’s
SETUP AND CALIBRATION
Your 758C Indicator has been thoroughly tested and calibrated before being shipped to you. If
you received the indicator with a scale, calibration is not necessary. If the indicator is being
connected to a scale for the first time or recalibration is necessary for other reasons, proceed
as indicated.
Calibration and Setup of the indicator is accomplished entirely by
the keypad. To enter the setup and calibration mode:
1. With the power off, remove the 2 screws from the right
end cap (as viewed from the indicator back) and remove
the end cap.
2. Locate the calibration jumper J2 on the circuit board and
remove the jumper. See Figure No. 9.
3. With the jumper removed, press and hold the
LOCK/RELEASE key and then press the ON/OFF key.
4. The indicator will perform a display test (turn on all digits),
show the software version for a few seconds and then
change to show SETUP.
5. Release the LOCK/RELEASE key.
6. The display will change to setgC.
7. The indicator is now ready for setup and calibration
Calibration
Jumper J2
Figure No. 9
During the setup and calibration process it is necessary to enter operational parameters via the
indicator's keypad. The following keys and the numeric keypad are used to input the values.
ON/OFF
PRINT/ENTER
NO
YES
1. Pressing the PRINT/ENTER key without entering a new value will retain the current
setting and advance to the next prompt.
2. Some prompts require only a YES or NO selection.
3. Other prompts require a numeric value to be entered. Use the numeric keypad to enter
the new value.
4. In either case, pressing the PRINT/ENTER key after changing a setting will save the new
value and advance to the next prompt.
CAUTION! The membrane keypad is not to be operated with pointed
objects (pencils, pens, fingernails, etc). Damage to keypad resulting from
this practice will NOT be covered under warranty.
setgC (SET GRAVITY CONSTANT)
This indicator is equipped with an acceleration of gravity function which means that it can be
calibrated in one location and then adjusted to match the acceleration of gravity at the
location where it will used.
With display showing setgC, press PRINT/ENTER key to show current setting. If setting
displayed is acceptable, press PRINT/ENTER key to save it. Otherwise use numeric keys
0/NO or 1/YES and enter a new setting. Press PRINT/ENTER key to save it.
0 = Gravity Constant is NOT used
1 = Set Gravity Constant
NOTE: If you select 1 (Set Gravity Constant) two additional prompts will be displayed.
8555-M210-O1 Rev R y 758C Owner’s
19
SETUP AND CALIBRATION, CONT.
CALgC (CALIBRATED GRAVITY CONSTANT)
With display showing CALgC, press PRINT/ENTER key to show current setting. This is the
acceleration of gravity value of the location where the scale was calibrated.
If the value displayed is acceptable, press PRINT/ENTER key to save it. Otherwise, using
numeric keys, enter a new value and then press PRINT/ENTER key to save it. Consult the
factory Tech Support for the Acceleration of Gravity value for your location.
OPgC= (OPERATING GRAVITY CONSTANT)
With display showing OPgC=, press PRINT/ENTER key to show current setting. This is the
acceleration of gravity value for the location where the scale will be operated.
If setting displayed is acceptable, press PRINT/ENTER key to save it. Otherwise, using
numeric keys, enter a new value and then press PRINT/ENTER key to save it. Consult the
factory Tech Support for the Acceleration of Gravity value for your location.
IMPORTANT! Once the Gravity Constant has been set, both CALgC
and oPgC= must be set to the same value to disable it.
int= (INTERVAL SETTING)
Press PRINT/ENTER key to show current setting. If value displayed is acceptable, press
PRINT/ENTER key to save it. Otherwise, using numeric keys, enter a new value and then
press PRINT/ENTER key to save it. Allowable values are 1, 2, 5 or 10.
NOTE: If you select an interval value of 10 (int=10), dPP= prompt will not be shown.
Setup will proceed to CAP=, scale capacity setting prompt.
Unit= (WEIGHING UNIT)
With display showing Unit=, press PRINT/ENTER key to show current setting. If value
displayed is acceptable, press PRINT/ENTER key again to save it. Otherwise, using numeric
keys, enter a new value and then press PRINT/ENTER key to save it. Allowable values are:
0 = None
1 = Pounds Only
2 = Kilograms Only
3 = Pounds/Kilograms
4 = Kilograms/Pounds
5 = Ounces Only
6 = Grams Only
7 = Stones and Pounds
or Kilograms
IMPORTANT! If Unit=7 (7 = Stones and Pounds or Kilograms) is selected, the value
selected for int= (Scale Interval) and dPP= (Decimal Point Position) must be set to (1).
NOTE: Weight display for Stones and Pounds/Kilograms mode is XX.YY.Y,
where XX is weight in Stones and YY.Y is remainder of the weight in pounds.
Please note that in this mode, "ST" and "lb" annunciators will be turned on.
dPP= (DECIMAL POINT POSITION)
With display showing dPP=, press PRINT/ENTER key to show current setting. If value
displayed is acceptable, press PRINT/ENTER key to save it. Otherwise, using numeric keys,
enter a new value and then press PRINT/ENTER key to save it. Allowable values are:
0 = XXXXXX
20
1= XXXXX.X
2 = XXXX.XX
8555-M210-O1 Rev R y 758C Owner’s
3 = XXX.XXX
SETUP AND CALIBRATION, CONT.
CAP= (SCALE CAPACITY)
With display showing CAP=, press PRINT/ENTER key to show current setting. If value
displayed is acceptable, press PRINT/ENTER key to save it. Otherwise, using numeric keys,
enter a new value and then press PRINT/ENTER key to save it. Allowable values are 1
through 99,999.
CAL= (CALIBRATION)
With display showing CAL=, press PRINT/ENTER key. Display will change to show current
setting 0 (0=NO). If scale has been previously calibrated and you wish to skip calibration and
proceed to trA=, Zero Tracking Range, simply press PRINT/ENTER key and internal
calibration factor will be retained.
To begin calibration, press 1/YES key to select yes and then press PRINT/ENTER key. After
pressing PRINT/ENTER key display will change to LOAd=.
LOAd= (LOAD CALIBRATION WEIGHT)
Display will change to LOAd= which is a prompt for entry of calibration weight value and
placement of this amount of test weights on scale platform.
1. Make certain scale platform is empty and free of debris.
2. Place the desired amount of calibrated test weights on scale platform. A minimum of
50% of scale's capacity is required. However 70% to 100% is recommended.
3. Press PRINT/ENTER key.
4. If the value displayed is acceptable, press the PRINT/ENTER key again. Otherwise,
determine the exact amount of test weights to be placed on scale platform, then using
numeric keys, enter this value.
5. Verify that the numbers entered are the same as the amount of test weights and then
press the PRINT/ENTER key.
6. Starting at the left and proceeding right, a series of dashes will appear on the display.
The dashes will stay on the display momentarily, then disappear, after which the display
will proceed to the UnLOd prompt.
UnLOd= (UNLOAD CALIBRATION WEIGHT)
With display showing the UnLOd prompt:
1. Remove the weights from the scale platform and then press the PRINT/ENTER key.
2. Starting at the left and preceding right, a series of dashes will appear on the display.
The dashes will stay on the display momentarily, then disappear, after which the
calibration factor will be saved and the display will proceed to the trA= prompt.
trL= (FOUR PERCENT ZERO TRACKING RANGE LIMIT)
This setting determines whether a 4% limit is placed on zero tracking and push button zero
and selects the format when printing the date.
If enabled, (trL= 1) zero tracking and push button zero is limited to 4 % of scale capacity
and the date format is dd/mm/yy.
If disabled, (trL= 0) zero tracking and push button zero will operate up to full scale
capacity and the date format is mm/dd/yy.
With display showing trL=, press PRINT/ENTER key to show current setting. If setting
displayed is acceptable, press the PRINT/ENTER key to save it. Otherwise use numeric
keys 0/NO or 1/YES and enter a new setting. Press PRINT/ENTER key to save it.
8555-M210-O1 Rev R y 758C Owner’s
21
SETUP AND CALIBRATION, CONT.
UnS= (UNSTABLE RANGE)
The Unstable Range is the number of divisions of change permitted before the STABLE
annunciator turns off.
With display showing Un5=, press PRINT/ENTER key to show current setting. If value
displayed is acceptable, press PRINT/ENTER key to save it. Otherwise, using numeric keys,
enter a new value and then press PRINT/ENTER key to save it. Allowable values are 1
through 9.
FLt= (DIGITAL FILTER LEVEL SELECTION)
Display will change to show FLt= (prompt for selection of digital filtering level). Your
indicator will arrive with factory filter settings (1 = minimal) entered. Please check with your
scale service technician should you wish to change filter level and break range.
Press PRINT/ENTER key to show current setting. If value displayed is acceptable, press
PRINT/ENTER key to save it. Otherwise, using numeric keys, enter a new value and then
press PRINT/ENTER key to save it. Allowable values are 0, 1, 2 or 3. Note, that if you select
3 (Custom Filtering) two additional prompts will be displayed.
0 = Disabled – NO Filtering
1 = MINIMAL FILTERING
2 = MODERATE FILTERING
3 = CUSTOM FILTERING
NOTE: The prompts, F= (Filter Level) and br= (Break Range) will only be displayed if
you select 3 (Custom Filtering) for the FLt= Digital Filter Level.
F= (FILTER LEVEL)
With Custom Filtering selected, the display will change to show FL= (Filter Level). Filter
level is a number from 1 (least) to 16 (greatest) that corresponds to the amount of filtering.
Press PRINT/ENTER key to show current setting. If value displayed is acceptable, press
PRINT/ENTER key to save it. Otherwise, using numeric keys, enter a new value and then
press PRINT/ENTER key to save it. Allowable values are 1 through 16.
br= (BREAK RANGE)
The Break Range is a number from 1 to 64 that corresponds to the number of division
changes to break out of filtering.
With display showing br=, press PRINT/ENTER key to show current setting. If value
displayed is acceptable, press PRINT/ENTER key to save it. Otherwise, using numeric
keys, enter a new value and then press PRINT/ENTER key to save it. Allowable values are
1 through 64.
Sr= (SAMPLE RATE)
With display showing Sr=, press PRINT/ENTER key to show current setting. If value
displayed is acceptable, press PRINT/ENTER key to save it. Otherwise, using numeric keys,
enter a new value and then press PRINT/ENTER key to save it. The sample rate may be set
from a minimum of 1 sample per second to a maximum of 10 samples per second in one
sample per second intervals. Allowable values are 1 through 10.
22
8555-M210-O1 Rev R y 758C Owner’s
SETUP AND CALIBRATION, CONT.
HOLd= (HOLD MODE)
With display showing HOLd=, press PRINT/ENTER key to show current setting. If value
displayed is acceptable, press PRINT/ENTER key to save it. Otherwise, using numeric keys,
enter a new value and then press PRINT/ENTER key to save it. Allowable values are:
0 = NO (disable)
1 = YES (enable)
2 = AUTO (Automatic Hold)
x
If HOLd=0 or1 (NO or YES) is selected, proceed to type= (Type) section.
x
If HOLd= 2 (AUTO) is selected, an additional prompt bAnd= (Auto Lock Reset Band)
will be displayed and the tYPE= (Operation Mode) prompt will not be shown. The
operation mode will automatically be set to 0 (Transaction Storage Mode). Proceed to
bAnd= (Auto Lock Reset Band) to continue setup.
With Hold feature enabled (HOLd=1), the indicator will lock the displayed weight on the
display when LOCK/RELEASE key is pressed. Pressing the key again will unlock display.
If automatic hold (HOLd=2) is selected, the indicator will automatically lock the weight on the
display after obtaining a stable weight value that exceeds the Auto Lock Reset Band value.
Refer to the next prompt Auto Lock Reset Band.
IMPORTANT! HOLD mode of operation is only used in non-commercial
applications and must be set to 0 = NO (disabled) for "Legal for Trade"
applications.
bAnd= (AUTO LOCK RESET BAND)
If Automatic Lock is selected, display will change to show bAnd= (Auto Lock Reset Band
value). This is the number of division changes needed to reset the auto lock. For Automatic
Lock to function, load on scale must rise above bAnd= value (and remain stable). To release
Automatic Lock, load on scale must fall below bAnd= value. At that point, next weighing
operation can begin.
Press PRINT/ENTER key to show current setting. If value displayed is acceptable, press
PRINT/ENTER key to save it. Otherwise, using numeric keys, enter a new value and then
press PRINT/ENTER key to save it. Allowable values are: 0 through 99.
type= (STORAGE OPERATION MODE)
This setting determines whether the indicator operates in the Transaction Storage Mode (no
ID storage) or in the ID Storage Mode. Note that the ID Storage Mode allows up to 99 ID’s.
With the display showing tYPE=, press the PRINT/ENTER key to show current setting. If the
setting displayed is acceptable, press the PRINT/ENTER key to save it. Otherwise, using the
numeric keys, 0/NO or 1/YES, enter the new setting, then press the PRINT/ENTER key to
save it.
0 = Transaction Storage
1 = ID Storage Enabled
8555-M210-O1 Rev R y 758C Owner’s
23
SETUP AND CALIBRATION, CONT.
HirES= (High Resolution Mode)
The High Resolution Mode feature will display the weight at 10 times the standard resolution.
For example, a 758C configured for 400 lb x 0.2 lb will display weight in high resolution mode
at 400 lb x 0.02 lb.
With the display showing HirES=, press the PRINT/ENTER key to show current setting. If
the setting displayed is acceptable, press the PRINT/ENTER key to save it. Otherwise, using
the numeric keys, 0/NO or 1/YES, enter the new setting, then press the PRINT/ENTER key to
save it.
0 = NO (If High Resolution Weight
mode is not desired)
1 = YES (If High Resolution Weight
mode is desired)
NOTE: If HirES=1 (YES) is selected, the indicator will exit Setup and Calibration,
reset and then display weight in the High Resolution Weight mode.
To return to Setup and Calibration:
1. Press the ON/OFF key.
2. Press and hold the LOCK/RELEASE key and then press the ON/OFF key.
3. The indicator will perform a display test (turn on all digits), show the software
version for a few seconds and then change to show SETUP.
4. Release the LOCK/RELEASE key.
5. The display will change to setgC.
6. The indicator is now ready to continue setup and calibration from the beginning.
trA= (ZERO TRACKING RANGE)
Zero tracking range is a value in scale divisions that will be automatically zeroed off. With the
display showing trA=, press PRINT/ENTER key to show current setting. If value displayed
is acceptable, press PRINT/ENTER key to save it. Otherwise, using numeric keys, enter a
new value and then press PRINT/ENTER key to save it. Allowable values are 1 through 18
(1 to 9 divisions by 0.5 divisions). Enter a 0 (zero) to disable zero tracking.
allyn= (WELCH ALLYN)
This setting determines whether the USB port of the indicator is interfaced to a Welch Allyn
device (with an activated license). NOTE: Must purchase WACONNECT (which includes a
license key and USB cable) from Detecto to initiate connectivity with the Welch Allyn device.
With display showing Allyn=, press PRINT/ENTER key to show current setting. If setting
displayed is acceptable, press PRINT/ENTER key to save it. Otherwise use numeric keys
0/NO or 1/YES and enter a new setting. Press PRINT/ENTER key to save it.
0 = NO, Indicator is NOT interfaced to
Welch Allyn device
1 = YES, Indicator IS interfaced to
Welch Allyn device
nin= (MINUTES)
With display showing nin=, press PRINT/ENTER key to show current setting. If value
displayed is acceptable, press PRINT/ENTER key to save it. Otherwise, using numeric keys,
enter a new value and then press PRINT/ENTER key to save it. Allowable values are: 0
through 59.
24
8555-M210-O1 Rev R y 758C Owner’s
SETUP AND CALIBRATION, CONT.
HH= (HOURS)
With display showing hh=, press PRINT/ENTER key to show current setting. If value
displayed is acceptable, press PRINT/ENTER key to save it. Otherwise, using numeric keys,
enter a new value and then press PRINT/ENTER key to save it. Allowable values are: 0
through 23.
NOTE: Time is entered in a 24-hour format. When entering times after noon (12:00 PM),
you must add 12 to time. For example, 3:00 PM would be entered as 15.
dd= (DAY)
With display showing dd=, press PRINT/ENTER key to show current setting. If value
displayed is acceptable, press PRINT/ENTER key to save it. Otherwise, using numeric keys,
enter a new value and then press PRINT/ENTER key to save it. Allowable values are: 1
through 31.
nn= (MONTH)
With display showing nn=, press PRINT/ENTER key to show current setting. If value
displayed is acceptable, press PRINT/ENTER key to save it. Otherwise, using numeric keys,
enter a new value and then press PRINT/ENTER key to save it. Allowable values are: 1
through 12.
yy= (YEAR)
With display showing yy=, press PRINT/ENTER key to show current setting. If value
displayed is acceptable, press PRINT/ENTER key to save it. Otherwise, using numeric keys,
enter a new value and then press PRINT/ENTER key to save it. Allowable values are: 00
through 99.
iD= (ID NUMBER FEATURE)
This setting determines whether the indicator allows an ID number to be entered prior to
beginning the weighing operation. This applies to both Basic Operation and with the BMI
feature enabled.
With display showing id=, press PRINT/ENTER key to show current setting. If setting
displayed is acceptable, press PRINT/ENTER key to save it. Otherwise use numeric keys
0/NO or 1/YES and enter a new setting. Press PRINT/ENTER key to save it.
0 = ID Disabled
1 = ID Enabled
iDBAR= (ID SCANNER)
This setting determines whether the indicator allows a scanner to be used to input an ID
number to be entered prior to beginning the weighing operation. This applies to both Basic
Operation and with the BMI feature enabled.
With display showing idbar=, press PRINT/ENTER key to show current setting. If setting
displayed is acceptable, press PRINT/ENTER key to save it. Otherwise use numeric keys
0/NO or 1/YES and enter a new setting. Press PRINT/ENTER key to save it.
0 = No Scanner
1 = Yes Scanner
IMPORTANT! If the Transaction Storage Mode is set to ID Storage Enabled (type= 1)
the idbar= prompt will not be displayed.
8555-M210-O1 Rev R y 758C Owner’s
25
SETUP AND CALIBRATION, CONT.
Htr= (DIGITAL HEIGHT ROD)
This setting determines whether the height rod port is enabled for the Detecto DHR (Digital
Height Rod). With the port enable and the height rod connected, the BMI will automatically
be calculated and displayed when the height rod is raised and placed on the patient’s head.
With display showing Htr=, press PRINT/ENTER key to show current setting. If setting
displayed is acceptable, press PRINT/ENTER key to save it. Otherwise use numeric keys
0/NO or 1/YES and enter a new setting. Press PRINT/ENTER key to save it.
0 = Height Rod Port is Disabled
1 = Height Rod Port is Enabled
bni= (BMI CALCULATION FEATURE)
This setting determines whether the indicator operates as a basic (weigh calculation only)
indicator or performs the Body Mass Index (BMI) calculation.
With display showing bni=, press PRINT/ENTER key to show current setting. If setting
displayed is acceptable, press PRINT/ENTER key to save it. Otherwise use numeric keys
0/NO or 1/YES and enter a new setting. Press PRINT/ENTER key to save it.
0 = BMI Disabled
1 = BMI Enabled
P220= (P220 PRINTER)
This setting determines whether weight data sent to the serial port is formatted for a P220
printer or a P185 printer (see CRLF= prompt to select P185 printing mode).
With display showing P220=, press PRINT/ENTER key to show current setting. If setting
displayed is acceptable, press PRINT/ENTER key to save it. Otherwise, using numeric keys
0/NO or 1/YES, enter a new setting, then press PRINT/ENTER key to save it.
0 = NO (Weight Data is Formatted for
P185 printer)
1 = YES (Weight Data is Formatted for
P220 printer)
IMPORTANT! If you select P220=1 (Weight Data is Formatted for P220 printer), the
display will skip to the baUd= prompt.
CrLF= (P185 PRINTER MODE)
This setting determines whether weight data sent to the serial port is formatted for a P185
printer in Journal mode or a P185 printer in Ticket mode. NOTE: If you select CRLF= 1,
(Ticket Mode), an additional prompt (EOP=) will be displayed.
With display showing CRLF=, press the PRINT/ENTER key to show current setting. If setting
displayed is acceptable, press PRINT/ENTER key to save it. Otherwise use numeric keys
0/NO or 1/YES and enter a new setting. Press PRINT/ENTER key to save it.
0 = Set Serial Format for P185 Printer
in Journal Mode
1 = Set Serial Format for P185 Printer
in Ticket Mode
IMPORTANT! The EOP= END OF PRINT LINEFEEDS prompt will only be displayed if
you select P220=0 and CRLF=1.
26
8555-M210-O1 Rev R y 758C Owner’s
SETUP AND CALIBRATION, CONT.
EOP= (END OF PRINT LINEFEEDS)
At the end of data sent to a printer, the indicator can send a number of line feed commands
to space the paper in the printer to a desired position for withdrawal or for the next print.
With display showing EOP=, press PRINT/ENTER key to show current setting. If value
displayed is acceptable, press PRINT/ENTER key to save it. Otherwise using numeric keys,
enter a new value and then press PRINT/ENTER key to save it. Allowable values are: 00
through 99.
BAUD= (SERIAL OUTPUT BAUD RATE)
With display showing baUd=, press PRINT/ENTER key to show current setting. If value
displayed is acceptable, press PRINT/ENTER key to save it. Otherwise using numeric keys,
enter a new value and then press PRINT/ENTER key to save it. Allowable values are: 0, 1,
2, 3, 4 or 5.
0 = 1200 Baud
3 = 9600 Baud
1 = 2400 Baud
4 = 19.2k Baud
2 = 4800 Baud
5 = 38.4k Baud
PPORT (PRINTER OR DATA PORT)
With display showing PPORT, press PRINT/ENTER key to show current setting. If value
displayed is acceptable, press PRINT/ENTER key to save it. Otherwise using numeric keys,
enter a new value and then press PRINT/ENTER key to save it. Allowable values are:
1 = Serial Port
2 = Ethernet (requires 758-IP option)
3 = USB Device Port
Cont1 (CONTINUOUS OUTPUT SERIAL PORT)
With display showing COnt1, press PRINT/ENTER key to show current setting. If setting
displayed is acceptable, press PRINT/ENTER key to save it. Otherwise use numeric keys
0/NO or 1/YES and enter a new setting. Press PRINT/ENTER key to save it.
0 = Serial Port Continuous
Output is Disabled
1 = Serial Port Continuous
Output is Enabled
COnt2 (CONTINOUS OUTPUT ETHERNET PORT)
With display showing COnt2, press PRINT/ENTER key to show current setting. If setting
displayed is acceptable, press PRINT/ENTER key to save it. Otherwise use numeric keys
0/NO or 1/YES and enter a new setting. Press PRINT/ENTER key to save it.
0 = Ethernet Port Continuous
Output is Disabled
1 = Ethernet Port Continuous
Output is Enabled
COnt3 (CONTINOUS OUTPUT USB DEVICE PORT)
With display showing COnt3, press PRINT/ENTER key to show current setting. If setting
displayed is acceptable, press PRINT/ENTER key to save it. Otherwise use numeric keys
0/NO or 1/YES and enter a new setting. Press PRINT/ENTER key to save it.
0 = USB Device Port Continuous
Output is Disabled
1 = USB Device Port Continuous
Output is Enable
8555-M210-O1 Rev R y 758C Owner’s
27
SETUP AND CALIBRATION, CONT.
btn= (BUTTON OPERATION)
This setting determines which keys (NET/GROSS, TARE, and/or ID/HEIGHT) are locked out
during normal operation.
Press PRINT/ENTER key to show current setting. If value displayed is acceptable, press
PRINT/ENTER key to save it. Otherwise using numeric keys, enter a new value and then
press PRINT/ENTER key to save it. Allowable values are 0, 1, 2 or 3.
0 = No Keys Disabled
2 = ID/HEIGHT Keys Disabled
1 = NET/GROSS and TARE Keys
Disabled
3 = NET/GROSS, TARE, and
ID/HEIGHT Keys Disabled
niCAd (BATTERY TYPE SELECTION)
This setting determines whether Alkaline, NiCad (or NiMH) batteries are used for battery
operation.
With display showing niCAd=, press PRINT/ENTER key to show current setting. If setting
displayed is acceptable, press PRINT/ENTER key to save it. Otherwise use numeric keys
0/NO or 1/YES and enter a new setting. Press PRINT/ENTER key to save it.
0 = Alkaline
1 = NiCad or NiMH
PUO= (POWER UP ZERO)
With display showing PUO=, press PRINT/ENTER key to show current setting. If setting
displayed is acceptable, press PRINT/ENTER key to save it. Otherwise use numeric keys
0/NO or 1/YES and enter a new setting. Press PRINT/ENTER key to save it and proceed to
the next prompt. Allowable values are 0 or 1.
0 = NO (Weight display will not be
reset to zero)
1 = YES (Weight display will be reset
to zero automatically on power up)
ASH= (AUTOMATIC SHUTOFF)
The Automatic Shutoff feature will turn the indicator off after a period of approximately 1 to 9
minutes of inactivity to prolong battery life. You must press ON/OFF key to turn indicator
back on.
With display showing ASH=, press PRINT/ENTER key to show current setting. If setting
displayed is acceptable, press PRINT/ENTER key to save it. Otherwise use numeric keys to
enter a new setting and then press PRINT/ENTER key to save it. Allowable values are 0
through 9 with 0 disabling Automatic Shutoff.
SLP= (SLEEP MODE)
The Sleep Mode feature also conserves battery power when the indicator remains unused for
a period of approximately 1 to 9 minutes. When enabled, the load cell excitation will be
reduced and the display will show SLEEP. The Sleep feature requires the indicator to remain
at the center of zero to activate, unlike Automatic Shutoff feature which only requires no
motion. Weight placed on scale will activate indicator and return it to weight mode.
With display showing SLP=, press PRINT/ENTER key to show current setting. If setting
displayed is acceptable, press PRINT/ENTER key to save it. Otherwise using numeric keys,
enter a new setting and then press PRINT/ENTER key to save it. Allowable values are 0
through 9 with 0 disabling Sleep Mode
28
8555-M210-O1 Rev R y 758C Owner’s
SETUP AND CALIBRATION, CONT.
Setup and Calibration Is Complete
The setup and calibration process has been completed. The indicator will reset and then
display weight. Remove power from the indicator, re-install the calibration jumper J2 removed
earlier and re-assemble for use. The indicator is now ready for normal operation.
8555-M210-O1 Rev R y 758C Owner’s
29
SETUP REVIEW
The 758C indicator allows several operational parameters to be reviewed and changed as
necessary without having to remove the calibration jumper J2 and enter the setup mode.
To Enter Setup Review
1. If indicator is on, press the ON/OFF key.
2. Press and hold the ZERO key and then press the ON/OFF key.
3. The indicator will perform a display test (turn on all digits), show the software version for
a few seconds and then change to show ruie|.
4. Release the ZERO key.
5. The display will change to HirES = (prompt to enable High Resolution Mode feature).
6. Refer to instructions listed in Setup and Calibration section of manual for information on
how to change these parameters.
Parameters in Setup Review will be processed in the following sequence:
¾
x
HirES
Enable High Resolution¾ Mode feature
x
Tra=
Select the number of scale divisions automatically zeroed on power up
x
Allyn= Select whether the indicator is interfaced to a Welch Allyn device
x
Nin=
Set the minutes portion of the time
x
HH=
Set the hours portion of the time
x
Dd=
Set the day of the month
x
Nn=
Set the month of the year
x
Yy=
Set the year
x
iD=
Enable or Disable ID number input feature
x
iDbar= Enable or Disable ID Scanner
x
Htr=
Enable or Disable Digital Height Rod Port
x
Bni=
Enable or Disable BMI calculation feature
x
P220=
Select weight data format for P220 printer or P185 printer
x
CrLF=
Set P185 Printer Mode (P185 Journal Mode or P185 Ticket Mode)
x
EOP=
Set Number of End Of Print linefeeds printed
x
bAUd=
Select baud rate for serial output
x
PPORT
Select Serial or Ethernet or USB Device port for Data Port
x
COnt!
Enable or Disable Serial Port Continuous Output
x
COnt2
Enable or Disable Ethernet Port Continuous Output
x
COnt3
Enable or Disable USB Device Port Continuous Output
x
Btn=
Enable or Disable NET/GROSS, TARE and/or ID/HEIGHT keys
x
niCAd
Select to use Ni-Cad (NiMH) or Alkaline batteries
x
PUO=
Enable or Disable automatic reset of weight display to zero on power up
x
ASH=
Disable or select number of minutes for automatic shutoff timer
x
SLP=
Disable or select number of minutes of inactivity at zero for sleep mode
NOTE: If HirES= 1 (YES) is selected, the indicator will exit Setup Review and display
weight in High Resolution Weight mode. To return to Setup Review, repeat steps 1 to 4
above.
30
8555-M210-O1 Rev R y 758C Owner’s
PRINTER TICKET FORMATS
P220 Ticket
If the P220 Ticket printer was selected, P220=1 (1 = Weight Data Formatted for P220 printer)
during setup and calibration of the indicator, the data will be transmitted in the following format:
If Pounds Only or Pounds/Kilograms
was selected for Unit=
If Kilograms Only, Kilograms/Pounds or Stones
and Pounds/Kilograms was selected for Unit=
Time, mm/dd/yy
Time, dd/mm/yy
ID:
BMI:
Height:
Weight:
ID:
BMI:
Height:
Weight:
xxxxxxxxxxx
xx.x
x' xx.x”
xxx.xuu G
xxx.xuu T
xxx.xuu N
xxxxxxxxxxx
xx.x
xx.x cm
xxx.xuu G
xxx.xuu PT
xxx.xuu N
NOTE: When the P220 printer is enabled, every time the indicator is powered on, it will print a
test ticket making sure the P220 printer is in the correct mode of operation.
If the printer is in the correct mode the ticket will look like:
OEPL1
Cardinal Scale Mfg
Test Label
If the printer is not in the correct mode, the ticket will look like:
Cardinal Scale Mfg
Test Label
NOTE: After printing the test ticket, the printer will switch to the correct mode.
P185 Journal Mode
If the P220 Ticket printer was not selected, P220=0 (0 = Weight Data Formatted for P185
printer) AND CRLF=0 (0 = Set Serial Format for P185 in Journal Mode) during setup and
calibration of the indicator, the data will be transmitted in the following format:
Weight, BMI, Height, Time, Date
P185 Ticket Mode
If the P220 Ticket printer was not selected, P220=0 (0 = 0 = Weight Data Formatted for P185
printer) AND CRLF=1 (1 = Set Serial Format for P185 Printer in Ticket Mode) during setup
and calibration of the indicator, the data will be transmitted in the following format:
If Pounds Only or Pounds/Kilograms
was selected for Unit=
If Kilograms Only, Kilograms/Pounds or Stones
and Pounds/Kilograms was selected for Unit=
Time, mm/dd/yy
Time, dd/mm/yy
ID:
BMI:
Height:
Weight:
ID:
BMI:
Height:
Weight:
xxxxxxxxxxx
xx.x
x' xx.x”
xxx.xuu G
xxx.xuu T
xxx.xuu N
xxxxxxxxxxx
xx.x
xx.x cm
xxx.xuu G
xxx.xuu PT
xxx.xuu N
NOTE: The P185 printer (both modes) doesn’t print a test ticket on power-up.
IMPORTANT! If ID or BMI are disabled, the field will be left out on any three formats.
8555-M210-O1 Rev R y 758C Owner’s
31
WEIGHT ON DEMAND FORMATS
Weight On Demand
If the continuous output was not selected for the serial port, Cont1=0, the USB Device port,
Cont2=0 or the optional Ethernet port, Cont3=0 and the indicator is connected to a
computer for transmission of weight data to a PC-based EMR (electronic medical record)
software program, it will transmit a single set of weight data each time the computer sends an
weight request “ENQ” (hex 05) or a SMA weight request “W”. This is known as Weight-OnDemand. Examples and explanation of the data format transmitted are shown below.
The host device (computer) sends:
ENQ (hex 05)
The 758C will respond:
<s><xxxxxx><d><uu><m><cc><cr>
Where:
s=
xxxxxx.xxx =
d=
uu =
m=
cc =
Sign
Weight
Decimal point
Units
Mode
Weight Status
cr =
Carriage Return
"-" = negative, " " (blank) = positive
Six digits
Added to string if enabled in setup
kg
G = Gross, N = Net
OC = overcap
CZ = center of zero
MO = motion
ee = weight not currently being displayed
(hex 0D)
SMA Standard Format
The host device (computer) sends:
<lf> W <cr>
The 758C will respond:
<lf>W01,<s><r><n><m><f><xxxxxx.xxx><uuu><cr>
Where:
32
lf =
W01
,
s=
Line Feed
W01
Comma
Flags
r=
n=
M=
f=
xxxxxx.xxx =
uuu =
cr =
Range
Mode
Motion
Custom
Weight
Units
Carriage Return
The text “W01”
(hex 2C)
Z= center of Zero, O = Overcap, E = zero Error,
e = weight not currently being displayed
1, 2, 3, ...
G = Gross, T = Tare, N = Net
M = Motion, " "(blank) = no motion
Custom flag
Six digits with decimal point
None, lb, kg, oz, g, st
(hex 0D)
8555-M210-O1 Rev R y 758C Owner’s
SERIAL AND USB DEVICE PORT COMMANDS
The following commands and formats apply to both the Serial port and the USB Device port.
Both the Serial port and USB Device port on the 758C are bi-directional ports and can receive
and transmit data. However, the USB Device port can only communicate with a computer.
The Serial port can output to a printer as well as communicate to a computer.
Serial Port
Using the serial port, it is possible to control the printing operation of the 758C by
transmitting commands to the indicator. Note that the PPORT parameter in the indicator
must be set to 1 = Serial Port to allow this.
USB Device Port
In order for the computer to communicate to the indicator using the USB Device port, the
computer requires the USB driver (758C_USB_Driver.inf, available on the Detecto Dealer
Web Site) and the PPORT parameter on the indicator must be set to 3 = USB Device Port.
Remote Print Command
The host device (computer) sends:
<LF> P <CR>
This command is equivalent to pressing the PRINT/ENTER key on the 758C keypad. The
758C will respond by printing a ticket using the serial port (or transmit data using the USB
Device port). The ticket will be printed (or data transmitted) in the following format:
If Pounds Only or Pounds/Kilograms
was selected for Unit=
If Kilograms Only, Kilograms/Pounds or Stones
and Pounds/Kilograms was selected for Unit=
Time, mm/dd/yy
Time, dd/mm/yy
ID:
BMI:
Height:
Weight:
ID:
BMI:
Height:
Weight:
xxxxxxxxxxx
xx.x
x' xx.x”
xxx.xuu G
xxx.xuu T
xxx.xuu N
xxxxxxxxxxx
xx.x
xx.x cm
xxx.xuu G
xxx.xuu PT
xxx.xuu N
Journal Mode Print Command
The host device (computer) sends:
<LF> J <CR>
This command is equivalent to pressing the PRINT/ENTER key on the 758C keypad. The
758C will respond by printing a ticket using the serial port (or transmit data using the USB
Device port). The ticket will be printed (or data transmitted) in the following format:
Weight, BMI, Height, Time, Date
NOTE: This command is equivalent to pressing the PRINT/ENTER key on the 758C
keypad with the P220 Serial Format Disabled and CRLF Enabled (P220=0), and the
CRLF set for Serial Format for P185 Journal Mode (Crlf=0) parameters selected. Note
that this command will print a ticket (or transmit data) in the above format regardless of
how the P220= and CrLF= parameters are set.
IMPORTANT! If ID or BMI are disabled, the field will be left out on any three formats.
8555-M210-O1 Rev R y 758C Owner’s
33
SERIAL AND USB DEVICE PORT COMMANDS, CONT.
Data Queue Commands
The 758C has been equipped with storage for weight records. When taking a weight record,
once the PRINT/ENTER key is pressed, the weight, ID (if enabled and entered), date and time
are stored in the indicator. The indicator can store up to 250 weight records. Once the limit is
reached, the oldest record will be over written to make room for the new weight record.
Delete Data Queue Command
The host device (computer) sends:
<LF> XD <CR>
The 758C will Delete the Data Queue.
Recall Data Queue Command
The host device (computer) sends:
<LF> XS <CR>
The 758C will Recall the Data Queue. The ticket will be printed (or data transmitted) in the
following format:
ID, Date, Time, Weight, Units, Mode<cr><lf>
Where:
ID =
Date =
Time =
Weight =
Units =
m=
cr =
lf =
xxxxxxxxxxx
mm/dd/yy
hh:mm
xxxxxx.x
uu
Mode
Carriage Return
Line Feed
Up to 11 digit ID number
Month, Day, Year
Hours and Minutes
Six digits with decimal point
None, lb, kg, oz, g, st
G = Gross
(hex 0D)
(hex 0A)
NOTE: Recalling the data queue does not delete the current data. The separate delete
command must be sent to clear the queue.
34
8555-M210-O1 Rev R y 758C Owner’s
ERROR AND STATUS DISPLAYS
Display
-Err-OF-
Meaning
General error, invalid keypad entry was attempted.
Attempting to display a negative number greater than –9,999 or a
positive number greater than 99,999
-trL-
Indicates an attempt to zero a weight outside scale zero range. Refer to
the Setup and Calibration trL= (Four Percent Zero Tracking Range
Limit) parameter.
-UnS-
Motion is present when indicator is attempting to perform one of the
following operations: Power Up, Zero, or Zero Weight Display
CALib
CERR
Indicates calibration is necessary.
AdErr
ErrA
ErrAL
ErrAH
EE Err
OCAP
Attempting to enter Setup and Calibration with the calibration jumper
(J2) installed.
Consult your scale service representative.
Scale weight exceeds scale capacity
BEFORE YOU CALL FOR SERVICE
Problem
Display does not
turn on
Possible Solutions
AC Operation:
x Is AC power supply fully inserted into wall receptacle?
x Check wall receptacle for proper AC power. Try another electrical
appliance in same receptacle, does it work?
x Check circuit breaker.
x Has there been power failure?
Battery operation:
x Check if batteries are installed and correctly.
x Are batteries discharged?
If Alkaline, remove old batteries and replace with new ones.
If NI-CAD or NiMH, remove discharged batteries and replace
with fully charged ones. Place discharged batteries in an
external charger to recharge.
Incorrect weight
displayed
Insure that scale platform isn't touching an adjacent object.
Have proper operation procedures been followed?
Indicator will not
display weight
Refer to Error and Status Display section and make certain that the
O CAP message is not displayed. If so, and scale is not loaded,
perform the calibration sequence.
Indicator displays
999.9 for height
The digital height rod was not in its “starting position” prior to turning
on the indicator. Push inner sliding tube completely down inside
outer stationary tube and fold headpiece against stationary tube.
8555-M210-O1 Rev R y 758C Owner’s
35
EVENT COUNTER
The 758C weight indicator has been designed with an Event Counter type of security seal.
When selected, the 758C will display two 3-digit numbers representing the Calibration and
Configuration counters.
Calibration Counter
The calibration counter is incremented when a value in the calibration part of setup is
changed (SetGC, CALGC, OPGC, int, Unit, UnS, dPP, CAP, FLt, F, br, Sr, CAL,). The
counter is only incremented 1 time even if more than one parameter is changed each time
through setup.
Configuration Counter
The configuration counter is incremented when a value in the configuration part of setup is
changed (Hold, bAnd, trA, PUO, niCAd, SLEEP, ASH). The counter is only incremented
1 time even if more than one parameter is changed each time through setup.
To Review the Event Counter:
1. If indicator is on, press the ON/OFF key.
2. Press and hold the UNITS key and then press the ON/OFF key.
3. The indicator will perform a display test (turn on all digits), show the software version for
a few seconds and then change to show CAL1 and CHC.
4. Release the UNITS key.
5. The display will then show two 3-digit numbers.
x The left number represents the setup Calibration counter.
x The right number represents the Configuration counter.
6. To return to the normal operation, press the UNITS key.
7. Otherwise press the ON/OFF key to turn off the indicator.
CARE AND CLEANING
36
ƒ
DO NOT submerge indicator in water, pour or spray water directly on indicator.
ƒ
DO NOT use acetone, thinner or other volatile solvents for cleaning.
ƒ
DO NOT expose equipment to temperature extremes.
ƒ
DO NOT place equipment in front of heating/cooling vents.
ƒ
DO clean the indicator with a damp soft cloth and mild non-abrasive detergent.
ƒ
DO remove power before cleaning with a damp cloth.
ƒ
ƒ
DO provide clean AC power and adequate protection against lightning damage.
DO keep the surroundings clear to provide clean and adequate air circulation.
8555-M210-O1 Rev R y 758C Owner’s
This page intentionally left blank.
8555-M210-O1 Rev R y 758C Owner’s
37
This page intentionally left blank.
38
8555-M210-O1 Rev R y 758C Owner’s
PARTS IDENTIFICATION
Rear View Detail
ITEM QTY. PART NUMBER
DESCRIPTION
1
1
593GR986
SERIAL TAG ASSEMBLY
3
2
6021-0687
SCW TRUSS HEAD #6-32 X .375 THMS
4
1
6021-1032
THUMB SCRW, 6-32 X 0.25
5
4
6021-2069
SCW TRUSS HEAD SHEET METAL #6 X .50 (WHITE)
6
4
6021-6008
SCW TRUSS HEAD SHEET-METAL #6 X.375” (BLACK)
8
4
6610-2000
JACK SOCKET
11
1
6650-0087
LABEL: MADE IN THE USA
12
8
6680-0004
WASHER LOCK INT. TOOTH #6 Z/P
13
4
6680-0052
WASHER LOCK HELICAL #4 Z/P
17
2
8555-B159-08
SPACER, 758C MOUNT
18
1
8555-B166-08
BATTERY COVER
19
1
8555-B452-08
BOX, THREE CONNECTOR
20
1
8555-B453-08
BOX, TWO CONNECTOR
22
2
8555-C213-08
END CAP
23
1
8555-C448-0A
REAR PANEL ASSEMBLY
Optional AC Adapters (not shown)
6800-1045
AC ADAPTER 100-240VAC/12VDC @ 1 AMP US PLUG
6800-1047
AC ADAPTER 100-240VAC/12VDC @ 1 AMP EURO PLUG
AC230AU
AC ADAPTER 100-240VAC/12VDC @ 1 AMP, AU PLUG
AC230UK
AC ADAPTER 100-240VAC/12VDC @ 1 AMP, UK PLUG
8555-M210-O1 Rev R y 758C Owner’s
39
PARTS IDENTIFICATION, CONT.
Inside Rear View Detail
ITEM QTY.
40
PART NUMBER
DESCRIPTION
2
4
6013-0039
NUT HEX #6-32
7
2
6024-0126
WASHER FLAT FOR 5/32” POP RIVET
9
1
6610-5119
BATTERY HOLDER 6-C CELLS
12
8
6680-0004
WASHER LOCK INT. TOOTH #6 Z/P
14
4
6680-0138
SPACER #6 X .187 NYLON
15
2
6680-0214
POP RIVET BH AL 5/32 DIA
16
1
8200-B369-08
GROUND SPRING
21
1
8555-B461-0A
CABLE: BATTERY
24
1
8555-C450-0A
FRONT PANEL WELDMENT
26
1
8555-D444-0A
BOARD ASSEMBLY – 758C
8555-M210-O1 Rev R y 758C Owner’s
PARTS IDENTIFICATION, CONT.
Battery Cover Detail
ITEM QTY.
PART NUMBER
593GR986
Side View Detail
DESCRIPTION
1
1
SERIAL TAG ASSEMBLY
2
4
6013-0039
NUT HEX #6-32
3
2
6021-0687
SCW TRUSS HEAD #6-32 X .375 THMS
4
1
6021-1032
THUMB SCRW, 6-32 X 0.25
5
4
6021-2069
SCW TRUSS HEAD SHEET METAL #6 X .50 (WHITE)
9
1
6610-5119
BATTERY HOLDER 6-C CELLS
10
1
6650-0018
GASKET MATERIAL 1” X 1/2” X 5 1/4”
12
8
6680-0004
WASHER LOCK INT. TOOTH #6 Z/P
14
4
6680-0138
SPACER #6 X .187 NYLON
16
1
8200-B369-08
GROUND SPRING
17
2
8555-B159-08
SPACER, 758C MOUNT
18
1
8555-B166-08
BATTERY COVER
19
1
8555-B445-08
BOX, THREE CONNECTOR
21
1
8555-B461-0A
CABLE: BATTERY
25
1
8555-D222-08
KEYPAD: 758CSV (INTERNATIONAL VERSION)
26
1
8555-D444-0A
BOARD ASEMBLY – 758C
8555-M210-O1 Rev R y 758C Owner’s
41
STATEMENT OF LIMITED WARRANTY
Detecto Scale warrants its equipment to be free from defects in
material and workmanship as follows: Detecto warrants to the
original purchaser only that it will repair or replace any part of
equipment which is defective in material or workmanship for a
period of one (1) year from date of shipment. Detecto shall be the
sole judge of what constitutes a defect.
During the first ninety (90) days Detecto may choose to supply all
necessary replacement parts and service during normal weekday
working hours at no charge to the buyer.
After the first ninety (90) days Detecto will supply parts and
service at the job site provided the owner agrees to pay the Dealer
for all travel time, including mileage and test equipment, as well as
any expenses incurred over the direct labor of the technician at the
job site. This limited warranty honors only labor performed by
Detecto authorized dealers.
This warranty does not apply to peripheral equipment not
manufactured by Detecto; this equipment will be covered by certain
manufacturer’s warranty only.
This warranty does not include replacement of expendable or
consumable parts. This does not apply to any item which has
deteriorated or damaged due to wear, accident, misuse, abuse,
improper line voltage, overloading, theft, lightning, fire, water or acts
of God, or due to extended storage or exposure while in purchaser’s
possession. This warranty does not apply to maintenance service.
Purchased parts will have a ninety (90) day repair or replacement
warranty only.
Detecto may require components be returned to the factory; they
must be properly packed and shipping charges prepaid. A return
authorization number must be obtained for all returns and marked
on the outside of all returned packages. Detecto accepts no
responsibility for loss or damage in transit.
42
8555-M210-O1 Rev R y 758C Owner’s
STATEMENT OF LIMITED WARRANTY
Conditions Which Void Limited Warranty
This warranty shall not apply to equipment which:
A.) Has been tampered with, defaced, mishandled or have had
repairs and modifications not authorized by Detecto.
B.) Has had serial number altered, defaced, or removed.
C.) Has not been grounded according to Detecto’s recommended
procedure.
Freight Carrier Damage
Claims for equipment damaged in transit must be referred to the
freight carrier in accordance with freight carrier regulations.
This warranty sets forth the extent of our liability for breach of any
warranty or deficiency in connection with the sale or use of the
product. Detecto will not be liable for consequential damages of any
nature, including but not limited to, loss of profit, delays or expenses,
whether based on tort or contract. Detecto reserves the right to
incorporate improvements in material and design without notice and
is not obligated to incorporate improvements in equipment
previously manufactured.
The foregoing is in lieu of all other warranties, express or implied
including any warranty that extends beyond the description of the
product including any warranty of merchantability or fitness for a
particular purpose. This warranty covers only those Detecto
products installed in the forty-eight (48) contiguous continental
United States.
Ph. (800) 641-2008
E-mail: [email protected]
203 E. Daugherty
Webb City, MO 64870
8555-M210-O1 Rev R y 758C Owner’s
02/06
Printed in USA
D268-WARRANTY-DET
43
44
8555-M210-O1 Rev R y 758C Owner’s
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement