Model 379LM-10 and 379LMC-10 Fingerprint Keyless Entry Overview

Model 379LM-10 and 379LMC-10 Fingerprint Keyless Entry Overview
Model 379LM-10 and 379LMC-10
Fingerprint Keyless Entry
Overview
To prevent possible SERIOUS INJURY or DEATH from a
moving gate or garage door:
• Install Keyless Entry Control within sight of the garage door,
out of reach of children at a minimum height of 5 feet
(1.5 m), and away from ALL moving parts of door.
• ALWAYS keep remote controls out of reach of children.
NEVER permit children to operate, or play with remote
control transmitters.
• Activate gate or door ONLY when it can be seen clearly, is
properly adjusted, and there are no obstructions to door
travel.
• ALWAYS keep gate or garage door in sight until completely
closed. NEVER permit anyone to cross path of moving gate or
door.
For use with any 315 MHz SECURITY® ® garage door openers
having a purple "learn" button (refer to Step 4.)
The system uses biometric technology that enables an
authorized user to gain access by scanning their fingerprint.
The sensor strip on the unit makes a numeric template of the
fingerprint that is unique to that user. The unit’s memory can
store up to ten fingerprints.
• The term “enroll” refers to scanning the fingerprint so the
device will recognize the user.
• The term “swipe” refers to the movement of the finger across
the sensor strip.
• The term “LED” stands for Light Emitting Diode. There are 6
LEDs located on the Fingerprint Keyless Entry.
When unit is on, it is programmed to shut off after a short period
of time. The unit’s sensor strip is sensitive so it is important to
read the Tips for Success before attempting to use the
Fingerprint Keyless Entry.
NOTICE: To comply with FCC and or Industry Canada (IC) rules, adjustment or modifications of
this receiver and/or transmitter are prohibited, except for changing the code setting or replacing
the battery. THERE ARE NO OTHER USER SERVICEABLE PARTS.
Tested to Comply with FCC Standards for Home or office use. Operation is subject to the following
two conditions: (1) this device may not cause harmful interference, and (2) this device must
accept any interference received, including interference that may cause undesired operation.
Step 1 Install the Unit
Tips for Success
1. Remove cover.
2. Fasten bottom screw to mounting surface. Allow 1/8" (3 mm)
to protrude above surface. Position unit on screw head and
adjust for snug fit.
3. Fasten top screw. Replace cover.
CORRECT
1. Make sure finger is clean and dry.
Place finger flat above the sensor strip
with the top knuckle above the sensor.
2. Swipe finger straight down keeping
firm contact with the sensor. The swipe
should be a slow, constant speed.
SPECIAL NOTES: Use the same finger for
every swipe. It is important to swipe finger slowly and firmly as
this is the reason most swipes fail.
1
Start swipe with
the top knuckle
above the
sensor strip.
Sensor Strip
Swipe finger straight down
keeping firm contact with
the sensor.
Sensor Strip
The scan
should end
at the tip of
finger.
INCORRECT
3
• Do not bend finger during swipe as this will only scan the tip of
your finger.
• Swipe finger straight down, not at an angle.
• Swipe flat, not tilted or rolled to one side.
2
1
Reference
Step 3 Enroll Additional Users
NOTE: The device can store up to ten fingerprints at a time.
An enrolled user must swipe finger first to enroll new user.
Cover
1. Open cover and wait until Ready
LED is lit.
ENROLL
Resend button: When
pressed the door will stop if
moving up or reverse if
moving down.
Enroll button: When
pressed the unit will go
into Enroll mode.
Send LED (yellow): Lit
after a passed fingerprint
scan and indicates that the
Resend button is active
and can be used to stop
or reverse door travel.
Ready LED (green): Lit
when unit is ready to scan
fingerprint.
SEND
2. Press and hold Enroll button until
Enroll LED starts to flash.
Enroll LED (yellow):
Lit when the unit is in
Enroll mode.
ENROLL
PASS
FAIL
READY
RETRY
2
ENROLL
SEND
Pass LED (green): Lit when
a scanned fingerprint
matches a stored print.
1
ENROLL
PASS
FAIL
READY
RETRY
Sensor Strip
Fail LED (red): Lit when
a scanned fingerprint
does not match a
stored print.
3. While the Enroll LED is flashing an
enrolled user must slowly and
firmly swipe finger.
Retry LED (yellow): Lit
when another swipe is
required.
3
Extra directions are located
on the inside of cover.
4. The Enroll LED and Ready LED
will light when ready for new user
to swipe finger.
4
ENROLL
SEND
Step 2 Enroll Initial User
5. New user should swipe finger
slowly and firmly down the sensor
strip until three passed swipes are
made.
NOTE: The unit requires 3 passed swipes to enroll a user.
1. Open cover to turn unit on. Wait
until Enroll LED and Ready LED
are lit (not flashing).
ENROLL
PASS
FAIL
READY
RETRY
5
ENROLL
SEND
ENROLL
PASS
FAIL
READY
RETRY
6. The Enroll LED and Pass LED will
flash when new user is enrolled.
Unit will return to Ready mode.
2. Swipe finger slowly and firmly
down the sensor strip until three
passed swipes are made.
6
ENROLL
NOTE: The Pass LED will light for a
passed swipe. The Retry LED will
light if another swipe is needed.
Swipe slowly and with more pressure
if this occurs.
SEND
3. After the third passed swipe, the
Enroll and Pass LED will flash.
Enrollment is complete.
SEND
ENROLL
FAIL
READY
RETRY
FAIL
READY
RETRY
NOTE: If cover is already open, press either the Resend or
the Enroll button to turn unit on. The Pass LED will light for a
passed swipe. The Retry LED will light if another swipe is
needed.
ENROLL
PASS
ENROLL
PASS
NOTE: If cover is already open, press
either the Resend or the Enroll button to turn unit on.
If the Ready LED is lit refer to Factory Reset in the
Erase/Reset section.
2
Step 4 Program to Opener
Step 5 Operation
1. Open cover and wait until Ready
LED is lit.
1
ENROLL
SEND
2. Swipe finger slowly and firmly
down the sensor strip.
2
3. The Pass LED will flash and
garage door will either open or
close.
3
ENROLL
PASS
FAIL
READY
RETRY
NOTE: The unit must have an enrolled user before it can be
programmed to the opener. Due to the 30 second time interval,
a second person may be needed to press the “learn” button. If
there is no purple “learn” button refer to Troubleshooting.
1. Press and release the purple “learn” button on the motor unit
of the garage door opener. See illustration above.
2. Open cover and wait for Ready
LED to light.
2
SEND
ENROLL
SEND
ENROLL
PASS
FAIL
READY
RETRY
ENROLL
ENROLL
PASS
FAIL
READY
RETRY
NOTE: If cover is already open, press either the Resend or the
Enroll button to turn unit on. The Fail or Retry LED will light if
another swipe is needed. If this occurs, swipe slowly and with
more pressure. It may require multiple swipes to get a passed
swipe.
3. Within 30 seconds of pressing the
3
“learn” button, slowly and firmly
swipe enrolled finger.
NOTE: The Retry LED will light if
another swipe is needed.
While the door is traveling the Send LED will be lit. During this
time the only way to reverse or stop the door is to press the
Resend button.
4. After a passed swipe the Pass
4
LED will light followed by a lit Send
LED. The opener lights will flash.
Programming is complete.
ENROLL
SEND
ENROLL
PASS
FAIL
READY
RETRY
5. If the opener lights don’t flash,
5
press and release the Resend
button at 1 second intervals for up
to 5 seconds until the opener
lights flash or the door moves.
Programming is complete.
NOTE: If unit will not program to opener repeat the steps above
or refer to Troubleshooting.
3
• If finger is enrolled but unit will not program to
opener:
Erase/Reset
K<
• To erase users:
NOTE: Erasing a user will erase ALL stored fingerprints. User
does NOT need to reprogram to opener.
1. Open cover and wait until Ready
1
LED is lit.
ENROLL
SEND
2. Enrolled user must slowly and
firmly swipe fingerprint.
ENROLL
PASS
FAIL
READY
RETRY
— Ensure that the opener has a purple “learn” button. If
opener does not have a purple “learn” button it is not
compatible with the unit.
• If the unit is in Enroll mode at power up:
— Complete enrollment process for initial user.
— The initial enroll process failed (signalled by a lit Enroll
LED and Fail LED) and must be repeated.
• If enrolling new user and all LEDs flash and unit
returns to Ready mode:
2
— The memory is full. In order to add new user, the memory
needs to be erased. Refer to Erase User or Factory Reset.
3. Press and hold the Enroll button
for at least 6 seconds. The Pass
LED and Fail LED will flash for 15
seconds. During this time the
Resend button is active. After 15
seconds the Enroll and Ready
LEDs will light indicating
fingerprints are erased. The unit
will return to Enroll mode.
• If the unit does not wake:
— A button may be stuck. Press Enroll and Resend buttons
to ensure free movement.
3
— The batteries may need to be replaced.
• If the Fail LED flashes during use:
— The batteries need to be replaced.
NOTE: If sensor is dirty, user should wipe sensor with a clean
finger. It is recommended that the sensor be periodically
cleaned with a lint-free cloth dampened with alcohol.
The Battery
• To return to Factory Reset state:
NOTE: Factory reset state will erase ALL stored fingerprints. This
method should be used ONLY when an enrolled user is not
available as it requires user to reprogram unit to opener.
1. Open cover and wait until Ready
LED is lit.
1
To prevent possible SERIOUS INJURY or DEATH:
• NEVER allow small children near batteries.
• If battery is swallowed, immediately notify doctor.
ENROLL
2. Press and hold the Enroll button
until all LEDs turn off. Release
button.
3. Again press and hold the Enroll
button until the Ready and Enroll
LEDs are lit and not flashing.
SEND
ENROLL
PASS
FAIL
READY
RETRY
The batteries should produce power for at
least one year. Replace when the Fail LED
flashes during use. The unit requires 4
AAA batteries.
Dispose of old batteries properly.
2
1. Slide cover completely off.
2. Unscrew the two screws and remove
the battery cover.
3. Replace the batteries. Screw the
battery cover back on.
4. Slide cover back into place.
3
Cover
Battery
Cover
Screws
ENROLL
SEND
ENROLL
PASS
FAIL
READY
RETRY
Troubleshooting
• If no known enrolled users are available:
— The memory must be erased using the Factory Reset
process.
• If no known enrolled users are available:
— Ensure that the Ready LED is lit before you swipe.
— Ensure that the fingerprint is swiped correctly (See Tips
for Success).
— Ensure that fingerprint is enrolled.
— Ensure that sufficient pressure is being applied to sensor
strip (do not press too hard).
— Ensure that the sensor and finger are not wet.
© 2008, The Chamberlain Group, Inc.
114A3597
Replacement parts:
Cover ............................................................41A6481
All Rights Reserved
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement