advertisement
D E P A R T M E N T O F T H E A R M Y T E C H N I C A L M A N U A L
ORGANIZATIONAL, DS, GS, AND
DEPOT MAINTENANCE MANUAL
(INCLUDING REPAIR PARTS LIST)
LIGHT TARGET SURVEYING
U/W RANGE POLE; SELF ILLUMINATING
W/CARRYING CASE (MILITARY DESIGN)
FSN 6675-612-1187
H E A D Q U A R T E R S ,
D E P A R T M E N T O F T H E A R M Y
3 MARCH 1966
CHANGE
NO. 6
Changes in force: C2, C3, C5 and C6
TM
5-6675-243-15
C6
HEADQUARTERS
DEPARTMENT OF THE ARMY
WASHINGTON, D. C., 26 AUGUST 1992
Operator, Organizational, Direct and General Support and Depot Maintenance
Manual Including Repair Parts List
LIGHT, TARGET, SURVEYING;
U/W RANGE POLE;
SELF-ILLUMINATING; W/CARRYING CASE
(MILITARY
DESIGN NSN 6675-00-612-1187
Approved for public release; Distribution is unlimited.
TM 5-6675-243-15, March 1966, changed as follows:
Page 35, Line 0089, change source code from
PO to
X20, and delete NSN 6145-233- 7472.
By Order of the Secretary of the Army:
Official:
MILTON H. HAMILTON
Administrative Assistant to the
Secretary of the Army
02258
GORDON R. SULLIVAN
General, United States Army
Chief of Staff
-
DISTRIBUTION:
To be distributed in accordance with DA Form 12-25-E, block 1096, operator,
Unit, Direct and General Support Maintenance requirements for
TM 5-6675-243-15.
1/(2 Blank)
TM 5-6675-243-15
T
ECHNICAL
M
A N U A L
No. 5-6675-243-15
TM 5-6675-243-15
HEADQUARTERS
DEPARTMENT OF THE ARMY
W
ASHINGTON
, D. C., 3 March 1966
Organizational, DS, GS, and Depot Maintenance Manual
(Including Repair Parts List)
LIGHT, TARGET, SURVEYING: U/W RANGE POLE;
SELF ILLUMINATING; W/CARRYING CASE (MILITARY DESIGN)
FSN 6675-612-1187
Section I.
II.
Section I.
II.
III.
Section I.
II.
III.
IV.
V.
Description and data-------------------------------------------------------- 3-5
INSTALLATION AND OPERATION INSTRUCTIONS
Service upon receipt of euipment-------------------------------------------- 6-8
Controls and instruments--------------------------------------------------
Operation of equipment----------------------------------------------------------------
Paragraph
OPERATOR AND ORGANIZATIONAL MAINTENANCE INSTRUCTIONS
Operator and organizational maintenance tools and equipment -------------------
Operator’s maintence------------------------------------------------------------------------------
Troubleshooting_____________________________________________________________
Front plate assembly--------------------------------------------------------------------- 22,23
Housing assembly-----------------------------------------------------------
DEMOLITION OF ENEMY MATERIEL TO PREVENT ENEMY USE--------
Section I.
II.
SHIPMENT AND LIMITED STORAGE
Shipment within zone of intirior------------------------------------------
Limited storage-------------------------------------------------------------
Section I.
II.
III.
IV.
DIRECTANDGENERAL SUPPORT AND DEPOT MAINTENANCE
INSTRUCTIONS
General-----------------------------------------------------------------------
Description and data------------------------------------------------------------
Special tools and equipment-------------------------------------------------- 46-48
Contacts____________________________________________________________________
REFERENCES------------------------------------------------------------------------------------------ ---------
BASIC ISSUE ITEMS LIST------------------------------------------------ ------
MAINTENANCE ALLOCATION-------------------------------------------- ------
ORGANIZATIONAL, DIRECT AND GENERAL SUPPORT AND DEPOT
MAINTENANCE REPAIR PARTS LISTS --------------------------------- -------
------------------------------------------------—-----—----------—--------------
- - - - - -
1
AGO 10117A
CHAPTER 1
INTRODUCTION
a. These instructions are published for the use of the personnel to whom the Military
Design Surveying Target Light is issued.
Chapters 1 through 5 provide information on
the operation and organizational maintenance of the equipment, accessories, components,
and attachments. Chapter 6 provides infor-
mation for direct and general support and depot maintenance. This manual also provides description of the main units and their functions in relationship to other components.
b. Appendix I contains a list of publications
applicable to this manual. Appendix II con-
tains the basic issue items authorized for the
initial operation. Appendix III contains the
maintenance allocation chart, The organizational, direct and general support and depot
maintenance repair parts is listed in appendix
c. Numbers in parentheses on illustrations
Section I.
GENERAL
indicate quantity. Numbers preceding nomenclature callouts on illustrations indicate the preferred maintenance sequence.
d. The direct reporting of errors, omissions, and recommendations for improving this manual by the individual user is authorized and encouraged. DA Form 2028 (Recommended Changes to DA Publications) will be used for reporting these improvements. This form will be completed using pencil, pen, or typewriter and forwarded to Commanding General, U. S. Army Mobility Equipment Center, ATTN: SMOME-MPD, 4300 Goodfellow
Boulevard, St. Louis, Me., 63120.
e. Report all equipment improvements recommendations as prescribed by TM 38-750.
For record and report forms applicable to the operator and organizational maintenance, refer to TM 38-750.
The Military Design Surveying Target
Light (figs. 1 and 2) is issued for use at night
under all weather conditions and blackout. The light supplies a light source for surveying within certain limits. The colors are red, green, and white. Light intensity is controlled by a rheostat. The light also illuminates the circular level vial to assist in initial leveling.
Section II. DESCRIPTION AND DATA
Identification and Tabulated Data
a. Identification. The surveying target light has an identification decalcomania, located topback, which contains the FSN, nomenclature, manufacturer, model number and contract number.
b. Tabulated Data
D i m e n s i o n s a n d w e i g h t s
Length --------------------------------------------- 8½ in.
Width ----------------------------------------------- 6½ in.
Height ----------------------------------------------- 5½ in.
Weight ---------------------------------------------- 1½ lb.
This manual covers only the military design surveying target light. No known differences exist for the unit covered by this manual.
2
AGO 10117A
Figure 1. Surveying target light, front and top view, with
shippng dimensions.
3
4
Figure 2. Surveying target light, back and bottom view.
AGO 10117A
CHAPTER 2
INSTALLATION AND OPERATION INSTRUCTIONS
a. Remove the tape securing the packing carton.
Section I. SERVICE UPON
RECEIPT OF EQUIPMENT
b. Remove the metal container with the surveying target light.
c. Remove the surveying target light from the metal container.
7. Inspecting and Servicing Equipment
a. Inspect the entire unit for loose or missing hardware and accessories.
b. Make sure all items are witih the surveying target light and in serviceable condition.
c. Correct all deficiencies or report to organizational maintenance,
8. Installation or Setting-Up Instructions
a. Remove the surveying target light from its carrying case.
b. Install batteries (para 18).
c. Mount the surveying target light on the range pole.
Section II. CONTROLS
AND INSTRUMENTS
This section describes, locates, illustrates, and furnishes the operator sufficient information about the various controls for proper operation of the surveying target light.
Refer to figure 3 for the purpose
tion of all controls and instruments.
AGO 10117A
5
Controls and instruments.
Section III. OPERATION OF EQUIPMENT
b. The operator must know how to perform
a. The instructions in this section are pubevery operation of which the target light is lished for the information and guidance of the capable. This section gives instructions on the personnel responsible for the operation of the operation of the unit. Since nearly every job surveying target light.
AGO 10117A
presents a different problem, the operator may have to vary given procedures to fit the individual job.
Figure 4. Target light operating instructions.
Refer to figure 4 for the surveying target
light operating instructions.
AGO 10117A
CHAPTER 3
OPERATOR AND ORGANIZATIONAL
MAINTENANCE INSTRUCTIONS
Section I. OPERATOR AND ORGANIZATIONAL MAINTENANCE
TOOLS AND EQUIPMENT
13. Special Tools and Equipment
No special tools or equipment are required to perform maintenance target light.
- on the surveying authorized for the surveying target light are
listed in the basic issue items list, (app. II).
Organizational Maintenance
14. Basic Issue Tools and Equipment
Organizational maintenance repair parts are
Tools and repair parts issued with or
listed and illustrated in appendix IV.
Section II. OPERATOR’S MAINTENANCE
which is the responsibility of the operator.
This section contains information on the
This maintenance includes the replacement of maintenance of the surveying target light the lamps and batteries.
8
Figure 5. Lamps, removal and instalation.
AGO 10117A
Figure 6. Batteries, removed and installation.
9
17. Lamps
a. Removal.
the lamps.
Refer to figure 5 and remove
b. Cleaning
(1)
and Inspection.
Clean the lamps with a clean cloth.
(2) Inspect for cracks, breaks, and a burned-out condition.
(3)
Replace a damaged or defective lamp.
c. Installation. Refer to figure 5 and install
the lamps.
a. Removal. Refer to figure 6 and remove
the batteries.
b. Cleaning and Inspection.
(1) Clean the batteries with a clean cloth. Clean any corrosion from the contacts with a wire brush.
(2)
(3)
Inspect for cracks, leaks, and corrosion.
Replace a damaged or defective battery.
c. Installation
the batteries.
Section iii. TROUBLESHOOTING
19. General 20. No Illumination in Target Light
This section contains information useful in
Probable cause
Possible remedy
diagnosing and correcting unsatisfactory
Lamp defective-------Replace lamp (para 17).
operation or failure of the surveying target
Battery defective------Replace battery ( para 18).
light. Each trouble symptom stated is followed by a list of probable causes of the trouble.
The possible remedy recommended is described
21. Illumination Cannot Be Controlled
opposite the probable cause. Any trouble be-
Probable cause Possible remedy
yond the scope of the organizational mainte-
Rheostat defective----Replace rheostat ( para 32).
nance will be reported to direct support maintenance.
This section contains information cm the maintenance of the f rent plate assembly which is the responsibility y of organizational maintenance. This maintenance does not include the replacement of the front plate contacts.
a. Removal. Refer to figure 7 and remove the
front plate assembly.
Section iV. FRONT PLATE ASSEMBLY
b. Cleaning and Inspection.
(1) Clean all metal parts with an approved cleaning solvent and dry thoroughly.
(2) Inspect for cracks, breaks, corrosion, and other damage.
(3) Replace a damaged or defective front plate assembly.
c. Installtion. Refer to figure 7 and install
the front plate assembly.
AGO 10117A
.
Figure 7. Front plate assembly, removal and installation.
This section contains information on the maintenance of the housing assembly and its components. These include the locking wedge, rheostat, lamp bracket, contact strip, mirror, level retainer and level, filter and contact assembly, and sight.
a. Removal. Refer to figure 8 and remove the
locking wedge.
Section V. HOUSING
ASSEMBLY
b.
Cleaning and Inspection.
(1) Clean all parts with an approved cleaning solvent and dry thoroughly.
(2) Inspect for cracks, breaks, and other damage.
(3) Replace a damaged or defective lock.
ing wedge.
c.
Installation. Refer to figure 8 and install
the locking wedge.
AGO 10117A
Figure 8. Locking wedge, rheostat knob, lamp bracket, and contact
strip, removal and installation.
a. Removal. Refer to figure 8 and remove
the rheostat knob.
b. Cleaning and Inspection.
(1) Clean the knob with an approved cleaning solvent and dry thoroughly.
(2) Inspect for cracks, breaks, and other danrage.
(3) Replace a damaged rheostat knob.
c. Installation. Refer to figure 8 and install
the rheostat knob.
AGO 10117A
Figure 9. Mirror, level retainer, and level, removal and instillation.
a. Removal. Refer to figure 8 and remove the
lamp bracket.
b. Cleaning and Inspection.
(1) Clean the bracket with an approved cleaning solvent and dry thoroughly.
(2) Inspect for cracks, breaks, and other damage.
(3) Replace a damaged lamp bracket.
c. Installation. Refer to figure 8 and install
the lamp bracket.
c. Installation. Refer to figure 8 and install
the contact strip.
a. Removal. Refer to figure 9 and remove
the mirror.
b. Cleaning and Inspection.
(1) Clean the mirror with a tissue or clean, lint free cloth.
(2) Inspect for scratches and other dam.
age.
(3) Replace a damaged or defective mirror.
c. Installation. Refer to figure 9 and install
the mirror.
a. Removal. Refer the contact strip.
b. Cleaning and Inspection.
(1) Clean all parts with an approved cleaning solvent and dry thoroghly.
(2) Inspect for cracks, brinks, corrosion, and other damage.
(3) Replace a damaged or’ defective contact strip.
AGO 10I17A
a. Removal.
(1) Remove the mirror (para 29).
(2) Refertko figure 9 and remove the level
retainer and level.
Figure 10. Filter and contact assembly, removal and installation.
b. Cleaning and Inspection.
(1) Clean all parts with a clean, dry, lint free cloth.
(2) Inspect for cracks, breaks, and other damage.
(3) Replace a damaged or defective level retainer and level.
c. Installation.
(1)
Refer to figure 9 and install the level
retainer and level.
(2)
31. Filter and Contact Assembly
a. Removal. Refer to figure 10
the filter and contact assembly.
and remove
b. Cleaning and Inspection.
(1) Clean the filter and contact assembly with a soft brush or clean, dry, lint free cloth.
(2) Inspect for cracks, breaks, and other damage.
(3) Replace a damaged or defective filter and contact assembly.
AGO 10117A
c. Installation. Refer to figure 10 and install
the filter and contact assembly.
a. Removal.
(1) Remove the rheostat knob ( para 26).
(2) Refer to figure 11 and remove the
rheostat.
AGO 10117A
Removal and installation.
b. Cleaning and Inspection.
(1) Clean all parts with an approved cleaning solvent and dry thoroughl y.
(2) Inspect for cracks, breaks, broken winding, corrosion, and other damage.
(3) Replace a damaged or defective rheostat.
Figure 12. Sight, removal and installation.
c. Installation.
(1) Refer to figure 11 and install the
rheostat.
(2) Install the rheostat knob (para 26).
a. Removal. Refer to figure 12 and remove
the sight.
b. Cleaning and Inspection.
(1) Clean all parts with an approved cleaning solvent and dry thoroughly.
(2) Inspect for cracks, breaks, and other damage.
(3) Replace a damaged or defective sight.
c. Installution. Refer to figure 12 and install
the sight.
AGO 10117A
CHAPTER 4
DEMOLITION OF MATERIEL TO PREVENT ENEMY USE
When capture or abandonment of the surveying target light to an enemy is imminent, the responsible unit commander must make the decision either to destroy the equipment or render it inoperative. Based on this decision, orders are issued which cover the desired extent of destruction. Whatever method of demolition is employed, it is essential to destroy the same vital parts of all surveying target lights and all corresponding repair parts.
Equipment Inoperative
Use hammers, sledge hammers, crowbars, picks, axes, or any other tools which may be available to destroy the surveying target light.
a. Burning. Rack rags, clothing, or canvas under and around the surveying target light.
Saturate this packing with gasoline, oil, or diesel fuel and ignite.
b. Submersion. Totally submerge the surveying target light in a body of water to provide water damage and concealment. Salt water will do greater damage to metal parts than fresh water.
All operators should receive thorough training in the destruction of the surveying target light. (Refer to FM 5–25. ) Simulated destruction using all of the methods listed above should be included in the operator training program. It must be emphasized in training that demolition operations are usually necessitated by critical situations, when. time available for carrying out destruction is limited.
For this reason, it is necessary that operators be thoroughly familiar with all methods of destruction and be able to carry out demolition instructions without reference to this or any other manual.
AGO 10117A
CHAPTER 5
SHIPMENT AND LIMITED STORAGE
Section i. SHIPMENT WITHIN ZONE OF INTERlOR
38. Preparation of Equipment for Shipment
a. General. Detailed instructions for the preparation of the surveying target light for domestic shipment are outlined within this paragraph.
b: Inspection. Equipment will be inspected for any unusual conditions such as damage, accumulation of water, rushing, and pilferage.
All deficiencies will be recorded on DA Form
2404 (Equipment Inspection and Maintenance
Worksheet).
c. Cleaning and Drying. Thorough cleaning and drying by an approved technique is the first essential procedure in any effective preservation process. Approved methods of cleaning and drying, types of preservatives, and methods of application are described in TM
38-230.
d. Painting. Paint all surfaces where paint has been removed or damaged Refer to TM
9-213 for detailed cleaning and painting instructions.
e. Marking. Shall conform to MIL-STD-
129.
39. Loading Equipment for Shipment
No specific instructions are required for loading the surveying target light for shipment.
40. Preparation of Equipment for Storage
a. General. Detailed instructions for pre serving and maintaining the surveying target light in limited storage are outlined within this paragraph. Limited storage is defined as storage not to exceed 6 months.
b. Inspection. Equipment will be inspected for any unusual conditions such as damage, accumulation of water, rusting, and pilferage.
All deficiencies will be recorded on DA Form
2404 (Equipment Inspection and Maintenance
Worksheet).
41. Inspection and Maintenance of
Equipment in Storage
Section ii. LIMITED STORAGE placed in storage, all scheduled preventive maintenance services, including inspection, will be suspended and preventive maintenance inspection will be performed as specified herein.
b. Worksheet and Preventive Maintenance.
Applicable forms listed in TM 38-750 will be prepared for each major item of equipment when initially placed in limited storage and every 90 days thereafter. Perform required maintenance promptly to make sure equipment is mechanically sound and ready for immediate use.
a. Inspection.
When equipment has been
AGO 10117A
CHAPTER 6
DIRECT AND GENERAL SUPPORT AND
DEPOT MAINTENANCE INSTRUCTIONS
Section I.
GENERAL
a. The following instructions are for direct and general support and depot maintenance personnel. They contain information that is beyond the scope of the tools, equipment, personnel, or supplies normally available to organizational maintenance.
b. Appendix I includes the list of publica-
tions applicable to direct and general support
and depot maintenance. Appendix III contains
the maintenance allocation chart. The direct and general support and depot maintenance
repair parts lists are listed in appendix IV.
For record and report forms applicable to direct and general support and depot maintenance, refer to TM 38-750.
For a complete description of the surveying
target light, refer to paragraph 3.
Section II. DESCRIPTION AND DATA
a. General. Tabulated data for the surveying target light for direct and general support and depot maintenance is not required.
b. Time Standards. Table 1 lists the number
of man-hours required under normal conditions for various operations in the maintenance and repair of the surveying target light.
The man-hours listed are not intended to be rigid standards. Under adverse conditions, the operations will take longer; but under ideal conditions with highly skilled mechanics, most of the operations can be accomplished in considerably less time.
Remove and Replace-
18 BODY, CAB, HOOD AND HULL
1808 CARRYING CASES :
Case assembly, carrying-----------------------------------------------------------------------------------------
67 PRECISION INSTRUMENTS AND SYSTEMS, MECHANICAL ELECTRICAL
6700 SURVEYING TARGET LIGHT :
Light, target surveying
(includes leveling and adjusting)-----------------------------------------------------------------------------
6702 OPTICS :
Sight assembly-------------------------------------------------------------------------------------------------
Mirror assembly-------------------------------------------------------------------------------------------------
Window assembly
(includes removal and installation of filter and contact assembly)-------------------------------------
Filters
(includes removal and installation of front plate assembly)------------------------------------------
0.1
0.1
0.2
0.2
0.3
0.6
AGO 10117A
Table 1. Time
Standards (Cont’d)
Remove and Replace-
6703
6704
6705
6710
6712
6718
MECHANICAL, STRUCTURAL AND PRECISION PARTS :
Housing assembly
(includes removal and installation of f rent plate, contact strip, mirror, battery cap, rheostaat locking wedge, light bracket, sight, filter and contact, locking wedge assemblies) . -------------------------------------------------
L o c k i n g w e d g e a w e m b l y - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -
K n o b , r h e o s t a t - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -
BATTERIES:
Battery ____________________________________________________________________________
LAMPS :
Bracket aasembly, lamp _________________________________________________________________
Lamps __________________________________________________________________________________
CIRCUIT COMPONENTS:
Rheostat assembly, potentiometer _________________________________________________
MOUNTED CONNECTING DEVICES:
Contacts
(with front plate assembly removed) -----------------------------------------------------
C o n t a c t s t r i p a s s e m b l y - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -
LEVEL:
Level, circular __________________________________________________________________________
1.5
0.1
0.1
0.1
0.1
0.1
0.1
0.8
0.1
0.1
Section Ill. SPECIAL TOOLS AND EQUIPMENT
46. Special TooIs and Equipment
tenance repair parts are listed and illustrated
No special tools or equipment are required
by direct and general support and depot maintenance personnel to perform maintenance on
48. Specially Designed Tools and Equipment
the surveying target light.
No specially designed tools or equipment are
47. Direct and General Support and
Depot Maintenance Repair Parts required by direct and general support and depot maintenance personnel toperforrn main-
Direct and general support and depot maintenance on the surveying target light.
This section contains information on the maintenance of the surveying target light which is the responsibility of direct and general support and depot maintenance. This maintenance includes the replacement of the front plate contacts and the fillter and contact assembly contacts.
a. Removal.
(1) Remove the front plate assembly
Section IV. CONTACTS
(2) Refer to figure 13 and remove the
front plate contacts.
b. Cleaning, Inspection, and Repair.
(1)
Clean all parts with an approved cleaning solvent and dry thoroughly.
(2)
Inspect for cracks, breaks, bends, corrosion, and other damage.
(3) Replace a damaged or defective contact.
c. Installation.
(1) Refer to figure 13 and install the
front plate contacts.
AGO 10117A
(2) Install the front plate assembly
Figure 13. Front plate contacts, removal and installation.
(1) Remove the filter
and contact assem-
51. Filter and Contact Assembly Contacts
a. Removal.
(2) Refer to figure 14 and remove the fil-
ter and cent.aat assembly contacts.
AGO 10117A
22
Figure 14. Filter and contact aasembly contacts
removal and installation.
b. Cleaning and Inspection.
(1)
Clean all parts with an approved cleaning solvent and dry thoroughly.
(2) Inspect for cracks, breaks, corrosion, and other damage.
(3) Replace a damaged or defective filter and contact assembly contact.
c. Installation.
(1) Refer to figure 14 and install the ‘fil-
ter and contact assembly contacts.
(2) Install the filter and contact assembly
A G O 1 0 1 1 7 A
APPENDIX I
REFERENCES
1.
Dictionaries of Terms and Abbreviations
AR 320-5
AR 320-50
Dictionary of United States Army Terms
Authorized Abbreviations and Brevity Codes
2.
Painting and Preservation
TM 9-213
Painting Instructions for Field Use
3 .
Preventive Maintenance
TM 38-750
The Army Equipment Record Procedures
4.
Publication Indexes
DA Pam 108-1 Index of Army Motion Pictures, Film Strips, Slides, and Phone-Recordings
DA Pam 310-1 Index of Administrative Publications
DA Pam 310–2 Index of Blank Forms
DA Pam 310–3 Index of Doctrinal, Training, and Organizational Publications
DA Pam 310-4 Index of Technical Manuals, Technical Bulletins, Supply Manuals, (types
7, 8, and 9), Supply Bulletins, Lubrication Orders, and Modification
Work Orders
DA Pam 310–5
Index of Graphic Training Aids and Devices
DA Pam 310–6
Index of Supply Catalogs and Supply Manuals
5.
Shipment and Limited Storage
TM 38-230
Preservation, Packaging, and Packing of Military Supplies and Equipment
6.
Training Aids
FM 21-6
FM 21-30
Techniques of Military Instructions
Military Symbols
AGO 10117A
APPENDIX II
BASIC ISSUE ITEMS LIST
1. General
2. Explanation of Columns Contained in
Section II
a. Source Codes. The information provided in each column is as follows:
(1)
(2)
(3)
Materiel. This space is left blank for identification of agencies assigned supply responsibility for parts. Refer to appropriate Federal and Department of Army supply catalogs.
Source. The selection status and source of supply for each part are indicated by the following code symbol: P-applied to high mortality repair parts which are stocked in or supplied from the supply service depot system, and authorized for use at indicated maintenance level.
Maintenance. The lowest maintenance level authorized to use, stock, install or manufacture the part is indicated by the following code symbol:
O—Organizational Maintenance.
b. Federal Stock Number. When a Federal stock number is available for a part, it will be shown in this column, and will be used for requisitioning purposes.
Section I. INTRODUCTION
Section II lists the accessories, tools, and publications required for maintenance and operation by the operator, initially issued with, or authorized for the surveying target light,
c. Description.
(1) The item name and a brief description of the part are shown.
(2) A five digit Federal supply code for manufacturers and/or other supply services is shown in parentheses followed by the manufacturer’s part number. This number will be used for requisitioning purposes when no Federal stock number is indicated in the
Federal stock number column.
d. Unit of Issue. If no abbreviation is shown in this column, the unit of issue is “each.”
e. Quantitv Authorized. This column lists the quantities of repair parts, accessories, tools, or publications authorized for issue to the equipment operator or crew as required.
f. Quantity Issued With Equipment. This column lists the quantities of repair parts, accessories, tools, or publications that are initially issued with each item of equipment. Those indicated by an asterisk are to be requisitioned through normal supply channels as required.
g. Illustrations. This column is subdivided into two columns which provide the following information:
(1) Figure number. Provides identifying number of the illustration.
(2) Item number. Provides the referenced number for the parts shown in the illustration.
AGO 10117A
Section II. BASIC ISSUE ITEMS LIST
GROUP 31
6135-120-1020
6240-797-2650
TM 5-6675-243-15
AGO 10117A
25
APPENDIX III
MAINTENANCE ALLOCATION
1. General
a. Section I provides a general explanation of all maintenance and repair functions authorized at various maintenance levels.
b. Section II designates overall responsibility for the performance of maintenance operations on the identified end item or component.
The implementation of the maintenance tests upon the end item or component will be consistent with the assigned maintenance operations.
c. Section III lists the special tools and test equipment required for each maintenance operation as referenced f rom Section II.
d. Section IV contains supplemental instructions, explanatory notes and/or illustrations required for a particular maintenance function.
2.
Explanation of Columns in Section II
a. Functional Group Number. The functional group is a numerical group set up on a functional basis. The applicable functional grouping indexes (obtained from TB 750-
93-1 ) are listed on the MAC in the appropriate numerical sequence. These indexes are normally set up in accordance with their function and proximity to each other.
b. Component Assembly Nomenclature. This column containns a brief description of the components of each functional group.
c. Essentiality. The essentiality column reflects whether or not an assembly, or repair part, is combat essential to the tactical use of the end item. The letter “E” in this column indicates an item is combat essential.
d. Maintenance Operations and Maintenance
Level.s. This column list-s the various maintenance operations (A through J) and indicates
Section I. INTRODUCTION the lowest maintenance level authorized to perform these operations. The symbol designations for the various maintenance levels are as fcdlows:
O/C -Operator or crew
O
-organizational
DS -Direct Support
GS
-General Support
D -Depot
The maintenance operations are defined as follows:
A-Service. Operations required periodically to keep the item in proper operating condition, i. e., to clean, preserve, drain, paint, and replenish fuel, lubricants, hydraulic, and deicing fluids, or compressed air supplies.
B-Adjust.
Regulate periodically to prevent malfunction. Adjustments will be made commensurate with adjustment procedures and associated equipment specifications.
C-Aline. Adjust two or more components of an electrical or mechanical system so that their functions are properly synchronized or adjusted.
D-Calibmte. Determine, check, or rectify the graduation of an instrument, weapon, or weapons system or components of a weapons system.
E-Inspect. Verify serviceability and detect incipient electrical or mechanical failure by close visual examination.
F-Test. Verify serviceability and detect incipient electrical or mechanical failure by measuring the mechanical or electrical characteristics of the item and comparing those characteristics with authorized standards.
Tests will be made commensurate with test procedures and with calibrated tools and/or test equipment referenced in the MAC.
26
G-Replace. Substitute serviceable components, assemblies and subassemblies for unserviceable counterpart or remove and install the same item when required for the performance of other maintenance operations.
H-Repair. Restore to a serviceable condition by replacing unserviceable parts or by any other action required using available tools, equipment and skills-to include welding, grinding, riveting, straightening, adjusting and facing.
I-Overhuul. Restore an item to a completely serviceable condition (as prescribed by serviceability standards developed and published by the commodity command) by employing technique of “Inspect and Repair Only as
Necessary” (IROAN). Maximum use of diagnostic and test equipment is combined with minimum disassemble y during overhaul.
“Overhaul” may be assigmd to any level of maintenance except organizational, provided the time, tools, equipment, repair parts authorization, and technical skills are available at that level. Normally, overhaul as applied to end items, is limited to depot maintenance level.
J-Rebuild. Restore to a condition comparable to new by disassembling to determine the condition of each component part, and reassembling using serviceable, rebuilt, or new assemblies, subassemblies, and parts.
e. Reference Note. This column, subdivided into columns “K” and “L,” is provided for referencing the special tool and test equipment requirements (sec. III) and remarks (sec. IV) that may be associated with maintenance operations (sec. II).
3. Explanation of Columns in Section III
a. Reference Code. This column consists of a number and a letter separated by a dash.
The number references the T&TE requirements column on the MAC. The letter represents the specific maintenance operation the item is to be used with. The letter is representative of columns A through J on the MAC.
b. Maintenance Level. This column shows the lowest level of maintenance authorized to use the special tool or test equipment.
c. Nomenclature. This column lists the name or identification of the tool or test equipment.
d. Tool Number. This column lists the manufacturer’s code and part number, or Federal stock number, of tools and test equipment.
4. Explanation of Columns in Section IV
a. Reference Code. This column consists of two letters separated by a dash, both of which are references to section II. The first letter references column L arid the second letter ref erences a maintenance operation, columns A through J.
b. Remarks. This column lists information pertinent to the maintenance operation being performed, as indicated on the MAC (sec. H).
Section II. MAINTENANCE ALLOCATION CHART
Group 18
AGO 10117A
27
group 67
2 8
Reference code
Section III. TOOL AND TEST EQUIPMENT REQUIREMENTS
Maintenance l e v e l
Nomenclature
No special tools or test requipment required
Tool number
Reference code
Section IV. REMARKS
Remarks
No remarks required
—
AGO 10117A
APPENDIX IV
ORGANIZATIONAL, DIRECT AND GENERAL SUPPORT,
AND DEPOT MAINTENANCE REPAIR PARTS LISTS
1. General
a. This appendix lists repair parts for organizational, direct and general support, and depot maintenance. It indicates the quantity of repair parts required to be stocked by organizational maintenance as their prescribed load.
It indicates the guide quantity factors to be used for initial repair parts stockage by direct and general support, and recommends quantities of repair parts for depot maintenance. Information and data contained herein serve as requisitioning reference material, and as a guide to determine stockage quantities of repair parts.
b. Price informaticm for stock-type repair parts may be obtained from applicable Federal supply catalogs and/or Supply Management
Data and Price List (ML) of the Department of Defense supply agencies.
c. Repair parts lists are arranged as follows:
(1) Individual parts and major assemblies are listed alphabetically by item name within the functional groups.
(2)
(3)
Assembly components and subassemblies are indented and listed alphabetically by item name under major assemblies.
Bulk material is listed in functional group 9501.
d. Allowances are based on 350 hours operational per year.
2. Explanation of Repair Parts, Tools Lists,
and Prescribed Load Listing (Table 2)
a. Source Code. This column is subdivided into four columns. The titles and information provided in each column are as follows:
Section I. INTRODUCTION
(l.) Materiel. This column is left blank.
For identificatiom of agencies assigned supply responsibility for parts, refer to appropriate Federal and Department of Army supply catalogs.
(2)
(a)
Source. The selection status and source of supply for each part are indicated by one of the following code symbols:
P-applied to high mortality repair parts which are stocked in or supplied from the Army Supply
System, and authorized for use at indicated maintenance categories.
(b)
M-applied to repair parts which are not procured or stocked but are to be manufactured at indicated maintenance categories.
(c)
Xl-applied to repair parts which are not procured or stocked, the requirement. for which will be supplied by use of higher assembly or components.
(3)
(d)
X2-applied to repair parts which are not stocked. The indicated maintenance category requiring such repair parts will attempt to obtain them through carmibaliza,tion; if not obtainable through cannibalization, such repair parts will be requisitioned with supporting justification through normal supply channels.
Note. Source coding is not shown on common hardware items ahown to be readily available in Army supply channels and through local procurement.
Maintenance.
AGO 10117A
(4)
(a)
(b)
The lowest maintenance level authorized to manufacture, assemble, and/or install the part is indicated by one of the following code symbols:
0-Organizational Maintenance
F-Direct Support Maintenance
(DS)
This column is left blank when components of kits or sets are listed that are not applicable to the item of equipment, or when an item is source coded XI.
Recoverability.
When no code is shown in the recoverability column the part is considered expendable.
b. Federal Stock Number. When a Federal stock number is available for a part, it will be shown in this column and will be used for requisitioning purposes.
c. Description.
(1)
(2)
(3)
The item name and a brief description of the part are shown.
A five-digit Federal supply cede for manufacturers and/or other supply service is shown in parentheses, followed by the manufacturer’s part number. This number will be used for requisitioning purposes when no Federal stock number is indicated in the
Federal stock number column.
Example: (08645) 86453
Repair part quantities included in kits, sets, and assemblies, that differ from the actual quantity used in this specific end item, are listed in parentheses.
(4)
When repair parts are source coded
“C,” the manufacturer’s pant number will be used for local procurement.
Note. When a minimum stockage sufficient to repair one item and/or assembly is authorized, this quantity will be indicated to the Description column with the notation
“minimum stockage of is authorized.
d. Unit of Issue. If no abbreviation is shown in this column, the unit of issue is “each.”
e. Quantity Incorporated in Unit. The actual number of parts used in the application indicated is shown in this column. A zero (0)
30 is shown when components of kits or sets are listed that are not applicable to this specific end item.
f. 15-Day Organizational Maintenance Al-
lowance. Shown for each repair part is either a quantity or asterisk allocation which indicates the following:
( l ) A guide quantity factor is shown for each repair part authorized to be stocked by organizational maintenance. This quantity is based on past experience with similar items and the latest mortality data for 350 hours operation per year. It is the average quantity required to provide one prescribed load for 1–5 and/or 6-10 items of equipment, for a 15-day period under average combat conditions.
Note. Combat essential items which must be stocked or on order at organizational maintenance at all times, regardless of demand, will be identified in the allowance column by a quantity in parentheses.
(2)
(3)
(4)
(5)
The quantity of repair pants authorized for stockage in accordance with the number of prescribed loads authorized by the major commander
are determined by using table 2.
Table 2 is a consolidation of items
quantitatively allocated in this manual. Quantities listed are for one prescribed load for a 15-day period. A minimum stockage sufficient to repair one item and/or assembly is authorized (e. g., if 3 belts are required, then 3 belts are allocated as the minimum stockage). This quantity will be indicated in the minimum stockage authorization column.
Units and organizations authorized more than one prescribed load will multiply the quantity listed in the appropriate end item density spread column of 1-5 or 6-10 by the number of prescribed loads.
When more than 10 equipments require support, multiply the quantity listed in the 6-10 column by the number of equipments and the number of authorized prescribed loads, divide by
10, and round to the nearest whole number.
AGO 10117A
Table 2. Prescribed Load Listing
Federal stock No.
Description
6135–120–1020 BATTERY, DRY: 1.5 volts,
6240-797-2650 type D cell, BA30.
LAMP, INCANDESCENT
(24455) No. 14.
Functional group
6704
6705
Minimum stockage authorization
Unit of issues
15 days organizational maintenance allowances
1-6 6-10
1
(3)
1
(3)
The resulting fraction is 0.8 therefore the authorized stockage is 7.
Example: If the quantity listed in the
6-10 column is 4, the number of equipments is 17, and the number of authorized prescribed loads is 3, the following formula would be used:
4 x 1 7 x 3 ÷ 1 0 = 2 0 . 4
The resulting fraction is 0.4; therefore the authorized stockage is 20.
Note. An exception is made for those units and organizations required to have on hand, boxed or packaged prescribed load(s) pursuant to a special mission assignment.
Such prescribed load (s) will be computed or selected separately from quantities au-
(6) thorized for stockage at permanent station.
Repair parts required to perform organizational maintenance, which are not authorized for stockage are iden-
(7)
(a)
tified by an asterisk, and are to be requisitioned for immediate use only.
Subsequent changes to allowances will be limited as follows:
No decrease in the stated quantity of combat essential items is au-
(b)
thorized.
No change in the range of items is authorized. If exception to the prescribed load listing or revision to allowances is considered necessary,
(c)
a recommendation should be forwarded to the U. S. Army Mobility
Equipment Center.
Decreases in the stated qunatity of items other than combat essential items are authorized to a minimum
AGO 10117A
Example: If the quantity listed in the
6-10 column is 4, the number of equipments is 17, and the number of authorized prescribed loads is 1, the following formula would be used: quantity sufficient to repair one item and/or assembly and increases in the stated quantity are authorized for all items when justified by demand and usage experience.
Detailed procedures for performing these adjustments are prescribed in AR 735-35.
g. Guide Quantities per 100 Equipments.
Shown for each repair part applicable direct and general support, and/or depot maintenance is either an allowance factor or an asterisk allocation which indicates the following:
(1) A guide quantity factor is shown for each part authorized to be stocked by direct and general support maintenance and supply support activities, and the number of repair parts recommended for depot maintenance.
This factor is based on the latest mortality data for 350 hours operation per year and is the average quantity required by the various maintenance activities to provide maintenance and supply support for 100 items of equipment for a 15-day period under average combat conditions.
(2)
The quantities of repair parts authorized for stockage are determind using the following mathematical formula:
Quantity of equipment to be supported, multiplied by the listed allowance factor, divided by 100.
Fractions derived from the use of the above formula will be rounded to whole numbers as follows: If the result is 1 or more and includes a fraction that is 0.5 or more, the quantity is rounded to the next higher number.
31
Example: If the number of equipment supported is 30 and the allowance factor for 100 equipments is 5, the following formula would be used:
3 0 x 5 ÷ 1 0 0 = 1 . 5
The resulting fraction is 0.5; therefore, the stockage is 2. If the result is 1 or more and includes a fraction of less than 0.5, the quantity is rounded to the next lower number.
When the computed result is less than
0.5, no quantity is authorized for direct and general support, and depot maintenance. However, if the item is combat essential, a quantity of 1 is authorized.
Example: If the number of equipment supported is 30 and the allowance factor for 100 equipments is 28, the following formula would be used:
30 x 28 ÷ 100 = 8.4
The resulting fraction is less than
0.5; therefore, the stockage is 8.
(3)
(4)
(5)
In the guide quantity columns for direct and general support maintenance, additional repair parts authorized for use but not for initial stockage are listed without a guide quantity factor. These items are identified by an asterisk and may be added to or deleted from stock when recorded demand experience justifies a change in stockage objective.
Parts that may be required for depot maintenance, in addition to those allocated, are identified by an asterisk.
These parts are to be requisitioned, when required, if not obtainable from reclamation, fabrication, or local procurement.
Combat essential items of a critical nature which must be stocked at direct and genenal support maintenance at all times, regardless of demand are identified in the allowance column by inclosing the allowance factor in parentheses.
h. Direct and General Support Maintenance
15-Da# Level.
(1) Direct support (DS). This column
32
lists the initial guide quantity allowance factors of repair parts authorized for initial stockage by direct support maintenance activities to provide direct support maintenance for Mobility Command equipment and to provide organizational maintenance repair parts for supported unlits for a 15-day period. Additional repair parts identified by an asterisk are explained in g above. Upon establish-.
ment of supply records, recorded demand experience will be used to compute stockage objectives on authorized repair parts. Review of stockage objectives will be performed in the time cycle prescribed by major commanders.
(2) General support ( GS). This column lists initial guide quantity allocation factors of repair parts authorized for initial stockage by general support maintenance activities to provide general support maintenance for Mobility
Command equipment for a 15-day period. Additional repair parts identified by an asterisk are explained in
g above. Upon establishment of supply records, recorded demand experience will be used to compute stockage objectives on authorized repair parts.
Review of the stockage objectives will be performed in the time cycle prescribed by major commanders.
(3)
Units with TOE capability of performing partial or complete direct and general support maintenance for organic Mobility Command equip-
ment. Units with TOE capability of performing partial or complete direct and general support maintenance for organic Mobility Command equipment will be authorized to stock direct and/ or general support repair parts only when specific agreements are made between the commander of the designated parts supply activity, normally
DSU (Direct Support Units) and using unit. Parts so furnished are in addition to the prescribed load and will be adjusted as demands indicate.
AGO 10117A
(4) Units with TOE mission to provide
maintenance for Mobility Command
equipment of supported units. Units organized under TOE’s with the assigned mission to provide direct and general support maintenance for Mobility Command equipment of sup ported units are authorized to stock direct and general support repair parts. These repair parts will be issued from the appropriate parts supply activity (parts depot and/or
DSU). Such stockage is in addition to the prescribed load and will be adjusted as demands indicate.
i. Depot Maintenance. This column lists the quantity of repair parts recommended for depot maintenance shops (non-TOE) to provide depot maintenance for 100 equipments.
Additional repair parts are allocated by an asterisk, for immediate use only. Explanation of the asterisk allowance is contained in g above.
j.
into
Illustrations. This column is subdivided two columns as follows:
(1) Figure number. Indicates the num-
(2) ber of the illustration in which the part is shown.
Item number. Indicates the reference number used to point out the part in the illustration.
3. Abbreviations
AWG-American Wire Gage dia-diameter ft-foot (feet.) id-inside diameter in.-inch (es) lg-long (length) mtg-mounting (s)
No.-number od-outside diameter thk-thick (ness) thd-thread (s) (cd) w-watt (s) w-wide (width
)
4.
Index to Federal Supply Code for Manufacturers
24455-Lamp Division of Consumer Products Group GECO.
96906-Military Standards.
97403-US Army Engineer Research and
Development Laboratories.
AGO 1017A
33
3 4
LIBE
7 ne.
; : - :
. .
. .
= s
. . :
: “ f f~~;~;l ;
NIM8ER
DESCRIPTION
I
C98E
MANUFACTURER’S
?491 no.
z
3
6qJ9
?
H xl
SECTION II - REPAIR PARTS LIST
GROUP 18 - BODY, CAB, HOOD AND HULL
Oooh
DC& g
Ccno
0011
Om
2013 plh
X20
&
&
*
X20
X20
53 W993-W3
1~ - WWM2 RACNS, KsXES, STNWS,
CMNYI I@ C&IS, CMLE REELS,
NW RWLS, CTC.
CASE, CMRYINO, wsEmLY
BL12NLE:
CCU
-:
CARRYIM~
CATCN: CASC
COVER: CACC
HIN02, 2TNWTUNAL, EXTIWED
PIN, 141NOE
PAD, =R:
CAAC, rOAM RUBUR,
2 Ill. W, h @ Ill.
LO, @ [W, TICK
PAO, -I
COVCR RUBSCR, b I/b IM. v,
6 ~jh IIA.
LO, m m. mm
STRAP, CARNYINO
97h03 Dl135Jh16A g7k03 113>17-3
97h33 11352-17-1
!#iJ &v;&
%$=6 -3-flb3
01135s-96-6 ypq 1135D-1 -k
GROUP 67. PRECISION INSTRUMENTS AND
SYSTEMS, MECHANICAL ELECTRICAL,
ELECTRONIC
Ools
0016
%;
Or&
E5i
~
X20 g
Xa
% g.
6700- TNEODDLITE
LIWT, TAIRSFX SWVEYIM
~
--YILIOW c~ ~yl
BATTERY
~~ =~yl
8TR I
●
FILTER AKI ~KT ASSEIUY
~1~1
TARACT L161W
LEVEL, CINCISM
MINNON MsEmLY
PLATE ~Y: rnwr
RETAINER, LEWL
NWDSTAT ASSEI@LY:
L I mlT
Slwr ~Y
~= -~y:
LOCKINQ z s
~
Oqw
2031
~ fJz+&j g
%#
bob
670a - OPTICS
X2il b675-#w4;; 7 FILTER}. anccu
Xso&675- f 03
;i&&aiY
?
%10
,;
~ m-ws
53W+4-3971
MINNM
=, ~)~:
=~, ~Hl~l
flLW.R WC
SIwr
~Y
❑
IRROR
AACOWLY uT@
%
0 53%=-6611
SAsc: Slwlr
SIQNT
ScFm, NACANIE1
●
l*nT ACACWBLY ma
6703- tmNANICAL, SmKTuNu, Am
PRECISION PANTS c~ =~y :
8ATTCRY s
~ g g !m-@4&4
0oh8 ml
X20
~
SPNlt@, IKLICAL; CawNEsslah
COIIIAC1,
●
A1lCRY
NOUSINQ: lARAC1
LIWIT
-1 \ F! L7CR MAD COIITCCT ACSCMBLV
PIN, SPRIND:
moo RCTAI+II~
1/16 III.
OIA, Ilk III. La
%t@h WCACTAT
97kJ3 DI 135D4A
97i03 1135C-llA
97&3 ll~lOA
97403 1135D-9A
97i03 1139.13A
9743311350->1
97$0311350. 2
97b3 113
&
97kD3 l135&3A
97k)3 1135D-*5
97b3 113> A
97i03 113
&
97i03 l1350-lo.h
97b3 11350-19
97k03 113915-3
9Jg y&2
23 %$!3
$Kg %AA’ ghq 11350-8.1
97&3 1135D-&
97403 11350-18-2
97403 11350-7-3
g ~ ‘-*’* ~ PL~BIJ-&’:,c
~: MOW
●
LATY. ASSC!IDLY
Nousllw
ASS2SUYI WINCAW
CAP, MIKcXI
Nousus WINSW !
:
;
=
:
.
:
GUIEIE w(S) PER uAJ EIOIIPS
:Z
. . .
“:=
15 041S MAINTENANCE
~E,oT
Uhtur
:- 0mE4#lz&110N OS
-
1-5 6-10
Ss
100 C,u,,”c~rs
1
2
1
2
1
~
●
●
●
●
●
t
1
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
+
●
●
●
+
●
●
1
● ●
1
1 SEE IANP6
● ● ●
1 SEE GSW6
1
1
●
●
●
●
●
●
●
●
6
●
●
●
2
● ●
+
!
2
:
:E Gfw~6 ~z :
SEE CNP6 2
:
: ‘:
● ●
:
;
:
:
: :
:
1
:
1
:
:
●
:
●
’
:
:
●
●
●
:
*
9
●
●
●
●
~
●
●
●
●
●
●
,
●
●
1
1
● ● ● ● ●
● ● ● ●
●
+
● ●
:
● ● ● ●
:
●
●
●
’
AGO 10117A
W&E
llnf
Mo.
: : - i
. .
.
8
:
F~fM~:L
NU9BER
DESCRIPTION
I
CODE
MANUFACTURER’S
*kRl “D.
%
:
:
:
GUIDE QTY(S) PER MAI EllUIPS g:.
:5
-
15 01?s M1l MI ENINCE
,Cpn,
UAI”l
O*n Illlzlllom OS
1-5 6.10
6s
100 Pa”, ? BE”l S
I LLUS1
: :
:
:
:
: -
%?
0067 am m69
cop
0071
Cc&
m61
0062
~
mp
0073 oo7h xl xl
:;
0
X xl o
*
X20
X20
X20
Po
5305-57+3029
53% %3029
6135-120-1020
9ASXET
RIVET, SOLIDI 1/16 III.
D14,
97403 {1350.6-4 scl#:2djH~l#sj:l&!:, yin., “03 “’’p%’
.
.
SH I ciD
WINOOW
;%f R%32;
9743311350.5-3
PLATE :
FRONT
RI VET, ~ 10;
CONTACT PLATC I(TO
RIVET, SWIOt
llOUSINO AASCMBLY WINDOW
9740311372-3-1
97k)3 1135Q-3A5
Malmrlllo
97k03 ‘n350.3A6
SCREW, NACHINE1
SMICLO ma
~s ~cHINEI rn~’f f’LA7~ A~=~Ly
MOLWTINQ
$?$ !’?;%3?2
i ~= ~t~y! LOCKINO
SCREW, EXTERNALLY RELIEVED MOY!
WCDOE ASSEMBLY, h-b TMO sIZE,
:jc~;o:;;&
1/8
IN. TMO LO
!fOGf, LoCKlffi
97JI03 1135C-10.
97110311350-10?
670\ - BATTERIES
BATTERY, ORYX 1.5
VOLTS, TYPE
D
CELL,
BA30
2
1 k
1
:
1
1
:
4
2
k
1
●
●
●
●
●
●
●
●
S2E w 67 2
●
●
●
●
●
1
●
●
●
+
●
●
b
●
*
●
●
●
●
●
●
●
●
●
●
●
15
17 ~
IT k
:{ i
17
,1
16 lb
1613
16
2
w9
1100
,101
,102
;~
x82
1083
X18k
So85
)&8
*
w w w
~
mm
CQ76
%’g
g
)086
)087
% w
*
:2
,107
108 log
X20
%3
$!
6705- FUSES m LWS
BRACNET SS.E~LY!
L I am
COVER:
BRACKCT
GASNETt
L 10HT C. RACKCT ASSEMBLY
9740311350-1 1A
97&3 11350.12-1
97LI03 113~12-3 y“tksmcmn~, ~LD,R ma, ;%; ;i3%”-’ 62y&g*
X20
X20 no
X20 59*7354
1)8
In. d,
1/2
IN LO
SCREW, JJ)JU5TKNT! @ NF2,
7/8
IN. LC4, CRCS, FLATPOINT
TM#S.SCREWc
L IQHT nRACKCT MTO
6710. CIRCUIT comtmrs
LEAD ASSDJELY, ELECTR I CAL i
RHEOSTAT TO
COMTACT 8TR I P ASSCA!8LY AND FRONT PLATC
CONTACT
14ANUFACTURE FRON;
TEPJONAJ. LUGS 18 AK
wIRc,
NO. 8
SCREW SIZE
96906 U3356.72-21
97k03 1 135&12-4
97403 1135cb12.2
Po 61~233-7b~
Mo
$$
g
X20 g. *,+,,-%* d
~
X20 o
5--’9
53%-637-P79
a
“k%% :%1
LOD ASSEl@LY, ELECTR I CAL t
RHEOSTAT
TO FILTCR #140 CO!T&CT ASSEMBLY
MANuFACTURE FRW;
WIRE, ELECTRICAL (6 IN.
REQUIRED)
RtKOSTAT ASSEl@LY;
GASKET:
KNOB;
RHEOSTAT
nHC0STA7
L IOHT
97k13 11350-7A
97k03 11’5C-7-2
97b03 11350-7.3
ypo’ 11350-7.1
:::;&:A;o O“M 9~#5 //33~ -74 s
SETSCREW spAcERI ,“EO=,,, PLASTIC
WASHER, !uXWTJLL I C:
RIKOSTAT ma,
0.3
IN. ID, 11/16
IN. L=,
-7
97b3 11350-7.4
9740311350-7.5
WASHER, HoNKTALL I C:
RMCOSTAT mm,
RUBEW SYNTMCTIC, n/32 IN. ID,
11/16 III.
00, 1/16
IN. TIM(
~R~, ~H{NEs RH~Q~7AT @~tMBLy MTQ
$$j’j ~:~:~
6712- KJUNTEO CONWECTIHO DEvIcES m
X20
g g
m
2
5310-827-7893
CC+ATACT ASSEt.SKYa
STRIP
Bl~lffi POSTt
BLACK
BINOlffi POST; RED
~ETl
CONTACT $TR I P M’10
INSUATCR, PLASTIC!
BINDINQ POST, RED
PLATE, COWTACT STRIP bIASHER, HONKTALLIC!
BINDINU POST,
RU88CR, ~/32 IN, 10,
~8 IN.
OD,
1/16 IN.
THK
NUT, PLAIN ROLua
BINOIMa Posl
CONTACT STRIP:
FRONT PLATC
97h03 11350-9A
97k33 113G5-9A6
:$:
97k03 11350.9.1
974031 1350+4
97k03 11350-kA
:;”g~
FT
FT
1
~
2
;
2 b
:
:
:
:
1
●
●
●
:
●
●
●
●
; ( ;) ( ;) ( :)
1
:
*
●
●
*
●
●
●
4
●
*
SEE < RP WI1
1
:
1
1
:
1
SEE t RPw 1
● ●
●
X*E C w 67( 3
● ●
● ●
●
: *
●
●
●
●
●
●
+
:
●
●
:
●
●
‘
“
●
:
●
+
:
●
●
●
● ●
*
:
*
●
●
●
*
:
●
●
*
●
●
●
●
●
●
●
●
●
●
●
●
●
●
9
●
●
:
●
●
●
●
●
●
●
‘
●
●
●
●
●
●
●
lh
●
*
:
la
18 2
18 3
1812
18 k
18 5
18 6
1911
19 1
19 k
19, 5
19 2
19 3
19 7
;;,:
●
●
;
●
●
18
1810
:“ :! J
*
●
18 7
18 8
1813
1 72
AGO 1017A
3 5
36
LINE no.
m
CODE!
DESCRIPTION
I
MANUFACTURER’S
.!0,, I P&nl Ho.
u d
X20 o
0
0 xl
Xm
X20
X20
Xm
X20
“X20
xl
X29 o 5305-050-3971
5305-550-5002
5305-558-2864
5305-637-7079
5305-045-1628
X26
X20 m“ o
5330-292-0564
5305-050-3906
RIVET, !X410t
CONTACT STRIP M7a, rRONT .
PLATE
97403 11350-3a5
FILTER MAO CCtA7ACX ASSEl@lY
97403 11350-13a
CAP 97403 11350-14-2
97403 11350-15-4
FILTER:
#LAaT IC,
●
RCCN
F IL72RI
?LAST t c . Rco
GASKET:
CAP -
97403 11350-15-3
97403 113550-14-4
-ET: PLATE
97403 11350-14-3
-: rlLICR CND CONTACT MSCMBLY
PIN SPRIK+21
I(JIOB RC?AININO,
I)V6 IN.
DIA, I/b IN. LO
SPRlffi. CON7M7
PLATE, ‘CC+ATAC7
SCREW. MACHINE:
rlL’rcR mm
s-;
MACHINE:
CAP I(TO
.$ti~ ~ ~~: CONTACT A8SCICBLY
SNAFT AM) PINIcN:
CONTACT ASSCMBLY
~~,
)4ACHINE:
CCUTACT SPRINE MTO sc~,
MACHINE:
CONTACT SIR I P CSSCMBLY
97403 11350-15-5
97403 11350-18-2
97403 11350-13-2
97403 11350-14-1
96906 MS35246-1
96906 MS 35233-13
97403 11350-15-1
97403 11350-15-2
96906 MS35233-31
MOUNTt NO
=~,
NACHIHII
FILICR ANO CONTACT
@6 m35223-26
ASSCM9LY NT+ PM MO, SLOTTCO,
No.
6-32
TND,
3/8
IN.
La
SPRIM2, tKLICAl, ~SSIONl
COMIAC1,
BATTCRY
$gc% )423523348
@03 11350.lC-3
6718- C@#&l AM LEVEL
LEVEL, CIRCULAR
-E ILLWAINA7’OR:
CLEAR PLMIIC p~klffi,
PREFORMIOI
LWCL M1a
R2TAItIER, LEVEL
S~,_14AtHlNE:
RCIA I NCR MTa
97403 11350-9-2
97403 11350-4-4
96906
MS28784-12
97403 11350-9-5
GROUP 95 - GENERAL USE STANDARDIZED
PARTS
Po 6145-233-7472
9501-
EALK MATERIAL
WIRE, ELE27FcICN.: 18 Am
GUIDE IllY(S) PER NAJ EQUIPS
Biro
1A, ”
Ills
—
●
●
●
●
●
●
●
●
*
●
●
●
●
9
●
●
●
●
.
—
AGO 10117A
AGO 10117A
1
2
3
REF
NO.
FUNCT
GROUP
1808
1808
1808
INDEX TO PARTS, FIGURE 15
ITEM
NAME
REF
NO.
COVER
4
PIN
PAD
5
6
FUNCT
GROUP
1808
1808
1808
ITEM
NAME
PAO
STRAP
CASE
Figure 15. case.
37
3 8
3
4
5
2
1
REF
NO.
6
7
8
9
6703
6702
6702
6718
FuNC T
GROUP
6703
6704
6712
6712
6703
INDEX TO PARTS, FIGURE 16
ITEM
NAME
REF
NO.
HOUSING
BATTERY
SCREW
SPRING
10
11
12
GASKET
CAP
MIRROR AY
SCREW
PACKING
13
14
15
16
17
FUNCT
GROUP
6718
6718
6718
6703
6703
6702
6702
6702
ITEM
NAME
LEVEL
RETAINER sCREW
WED GE
SCREW
SCREW
BASE
SIGHT
Figure 16. Light, target surveying.
AGO 10117A
2
REF
NO.
1
FUNCT
GROUP
6712
ITEM
NAME
RIVET
2 6712
CONTACT STRIP
3 6703
GASKET
INDEX TO PARTS, FIGURE 17
REF
NO.
4
FUNCT
GROUP
6703
ITEM
NAME
PLATE
6703
SHIELD
5
6 6703
HOUSING AY
REF
NO.
7
FUNCT
GROUP
6703
ITEM
NAME sCREW
8 6703 sCREW
9
6703
RIVET
Figure 17. Plate.
AGO 10117A
39
40
5
6
2
3
4
7
REF
NO.
1
6705
6705
6705
6712
FUNCT
GROUP
6712
6705
6705
INDEX TO PARTS, FIGURE 18
ITEM
NAME
REF
NO.
GASKET
GASKET
HOLOER
PIN
8
9
10
11
SCREW
THUMBSCREW
PLATE
12
13
14
FUNCT
GROUP
6712
6712
6712
6712
6705
6712
6712
ITEM
NAME
WASHER
BINDING POST
BINDING POST
SCREW
LAMP
NuT
INSULATOR
Figure 18. Bracket.
AGO 10117A
AGO 10117A
5
6
2
3
4
REF
NO.
1
FUNCT
GROUP
6710
6710
6710
6710
6710
67IO
INDEX TO PARTS, FIGURE 19
ITEM
NAME
REF
NO.
LEAD AY
7
RESISTOR
8
SPACER
9
GASKET
10
PLATE
11
WASHER
FUNCT
GROUP
6710
6703
6703
6710
6710
ITEM
NAME
WASHER
KNOB sETSCREW sCREW
LEAO AY
Figure 19. Rheostat.
41
3
4
7
8
5
6
INDEX TO PARTS, FIGURE 20
REF
NO.
1
FUNCT
GROUP
6702
ITEM
NAME
SCREW
2 6702 FILTER
6712
SHAFT-GEAR
6712
SHAFT-PINION
6712
6712
GASKET
PLATE
6712
GASKET
6712 CAP
9
10
6712
6703
SCREW
KNOB
11 6703
PIN
12
6712
SCREW
13
6702 FILTER
4 2
Figure 20.
Filter and contact.
AGO 10117A
Basic issue tools and equipment ____
Batteries ________________________
Paragraph
Contact strip assembly ____________
Controls and instruments __________
Demolition:
General ----------------------------------
Other demolition methods --------
To render the equipment inoperative --------------------------
Training ______________________
D e s c r i p t i o n - - - - - - - - - - - - - - - - - - - - - - -
Difference in models ______________
Direct and general support and depot maintenance repair parts ________
Filter and contact assembly ________
Filter and contact assembl y contacts __
Front Plate assembly _____________
Front plate contacts ______________
Identification and tabulated data ___
Inspecting and servicing equipment __
Inspection and maintenance of equipment in storage ____________
Installation or setting-up instruction --------------------------–
Lamp bracket ____________________
Page
L a m p s - - - - - - - - - - - - - - - - - - - - - - - - - - - -
Level retainer and level ------------
Loading equipment for shipment ____
L o c k i n g w e d g e - - - - - - - - - - - - - - - - - - -
Paragraph
Mirror _________________________
Organizational maintenance repair p a r t s - - - - - - - - - - - - - - - - - - - - - - - - - -
Preparation of equipment for shipment ____________________
Preparation of equipment for storage
Record and report forms ___________
Rheostat ______________________
Rheostat knob ____________________
S c o p e - - - - - - - - - - - - - - - - - - - - - - - - - - - -
Special tools and equipment ________
Specially designed tools and equipment –-–-–--–-––––----------
S i g h t - - - - - - - - - - - - - - - - - - - - - - - - - - - -
Target light operation -------------
Troubleshooting:
G e n e r a l - - - - - - - - - - - - - - - - - - - - - - - -
Illumination cannot be controlled _.
No illumination in target light ----
Unpacking the equipment __________
Page
AGO 10117A
By Order of the Secretary of the Army:
HAROLD K. JOHNSON,
General, United States Army,
Chief of Staff.
Official:
J. C. LAMBERT,
Major General, United States Army,
The Adjutant General.
Distribution:
Active Army:
USASA (2)
ACSI (1)
DCSLOG (1)
CNGB (1)
TSG (1)
CofEngrs (3)
CC-E (1)
Dir of Trans (1)
Cofspts (1)
USAMB (1)
USA Arty Bd (2)
USA Armor Bd (2)
USAIB (2)
USARADBD (2)
USAAESWBD (2)
USAAVNTBD (2)
USCONARC (3)
OS Maj Cored (5) except
USARJ (1)
USASETAF (2)
USAMOCOM (2)
USASMC (1)
USACDCEC (10)
MDW (1)
Armies (2) corps (2)
USAC (1)
Div (2)
Engr Bde (1)
USMA (2)
Svc Colleges (2)
Br Svc Sch (2)
Gen Dep (10)
Engr Dep (10)
Army Dep (2) except
TOAD (3)
USA Tml Cored (2)
NG: State AG (3)
USAR: Same as active Army except allowance is one (1) copy for each unit.
For explanation of abbreviations used, see AR 320–50.
Army Tml (1)
Div Engr (2)
Engr Dist (2)
USA Engr R&D Lab (3)
USAMEC (46)
Engr Cen (5)
USAREUR Engr Proc Cen (2)
USAREUR Engr Sup Con Agcy (10)
Engr FLDMS (2)
Ft Knox FLDMS (10)
Fld Cored, DASA (8)
AMS (3)
USACOMZEUR (2)
MAAG (1)
JBUSMC (1)
Unts org under fol TOE: 2 ea. UNOINDC
5-48
5-237 (5)
5-262 (5)
5-267 (1)
5-278 (5)
5-279
6-101
6-315
6–316
6-317
6-327
6-328
6-405
6-406
6-425
6-426
6-545
6-555
6-556
6-557
44
AGO 10117A
THE METRIC SYSTEM AND EQUIVALENTS
PIN : 026305-006
This fine document...
Was brought to you by me:
Liberated Manuals -- free army and government manuals
Why do I do it? I am tired of sleazy CD-ROM sellers, who take publicly available information, slap “watermarks” and other junk on it, and sell it.
Those masters of search engine manipulation make sure that their sites that sell free information, come up first in search engines. They did not create it...
They did not even scan it... Why should they get your money? Why are not letting you give those free manuals to your friends?
I am setting this document FREE. This document was made by the US
Government and is NOT protected by Copyright. Feel free to share, republish, sell and so on.
I am not asking you for donations, fees or handouts. If you can, please provide a link to liberatedmanuals.com, so that free manuals come up first in search engines:
<A HREF= http://www.liberatedmanuals.com/ >Free Military and Government Manuals</A>
–
Sincerely
–
Igor Chudov http://igor.chudov.com/
Chicago Machinery Movers
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project